colibri_imx6: use UUID for rootfs
PATCH 1/1 colibri_imx6: use UUID for rootfs
Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs partition. This fixes the issue, when MMC controllers are probed in a different order in U-boot and Linux kernel.
--- configs/colibri_imx6_defconfig | 1 + include/configs/colibri_imx6.h | 55 +++++++++++++++++++++++----------- 2 files changed, 38 insertions(+), 18 deletions(-)
configs/colibri_imx6_defconfig +1 -0
@@ -40,6 +40,7 @@ CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y +CONFIG_CMD_UUID=y CONFIG_CMD_USB=y CONFIG_CMD_USB_SDP=y CONFIG_CMD_USB_MASS_STORAGE=y
include/configs/colibri_imx6.h +37 -18
85 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH 1/1 colibri_imx6: use UUID for rootfs
Hi Igor
Thanks for cleaning that up.
Quoted 5 lines · Igor Opaniuk
Replace usage of "
/dev/mmcblk*p*" with a proper UUID of rootfs partition.
This fixes the issue, when MMC controllers are probed in a different order
in U-boot and Linux kernel.
Basically a dream come true (;-p). Looks fine and works with latest 2.8b6 as well as today's linux-next. Just a few minor comments below.
Quoted 1 line
Signed-off-by Igor Opaniuk <[email protected]>
With that addressed you may add my
And tackle all the other boards as well.
Quoted 54 lines
--- configs/colibri_imx6_defconfig | 1 + include/configs/colibri_imx6.h | 55 +++++++++++++++++++++++--------- -- 2 files changed, 38 insertions(+), 18 deletions(-)configs/colibri_imx6_defconfig +1
-0@@ -40,6 +40,7 @@ CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y +CONFIG_CMD_UUID=y CONFIG_CMD_USB=y CONFIG_CMD_USB_SDP=y CONFIG_CMD_USB_MASS_STORAGE=yinclude/configs/colibri_imx6.h +9
-6@@ -115,16 +115,22 @@ "imx6dl-colibri-cam-eval-v3.dtb fat 0 1"#define EMMC_BOOTCMD \ -"emmcargs=ip=off root=/dev/mmcblk0p2 rw,noatime rootfstype=ext4 " \ + "emmcdev=0\0" \ + "emmcbootpart=1\0" \ + "emmcrootpart=2\0" \ + "emmcfinduuid=part uuid mmc ${mmcdev}:${emmcrootpart} uuid\0" \ + "set_emmcargs=setenv emmcargs ip=off root=PARTUUID=${uuid} "\ + "rw,noatime rootfstype=ext4 " \ "rootwait\0" \ -"emmcboot=run setup; " \ + "emmcboot=run setup; run emmcfinduuid; run set_emmcargs; " \ "setenv bootargs ${defargs} ${emmcargs} ${setupargs} " \"${vidargs}; echo Booting from internal eMMC chip...; " \ -"run emmcdtbload; load mmc 0:1 ${kernel_addr_r} " \ -"${boot_file} && run fdt_fixup && " \ +"run emmcdtbload; load mmc ${emmcdev}:${emmcbootpart} " \ +"${kernel_addr_r} ${boot_file} && run fdt_fixup && " \"bootz ${kernel_addr_r} ${dtbparam}\0" \ -"emmcdtbload=setenv dtbparam; load mmc 0:1 ${fdt_addr_r} " \ - "${fdt_file} && setenv dtbparam \" - ${fdt_addr_r}\" &&true\0"
include/configs/colibri_imx6.h +1
-0+ "emmcdtbload=setenv dtbparam; load mmc${emmcdev}:${emmcbootpart} " \
include/configs/colibri_imx6.h line 136
Quoted 5 lines
include/configs/colibri_imx6.h +2
-0+"${fdt_addr_r} ${fdt_file} && " \ +"setenv dtbparam \" - ${fdt_addr_r}\" && true\0" #define MEM_LAYOUT_ENV_SETTINGS \"bootm_size=0x10000000\0" \
Looks great, except I would sort that stuff alphabetically again (applies to sdboot and usbboot as well). Just makes comparing things so much easier.
Quoted 61 lines
include/configs/colibri_imx6.h +9
-7@@ -147,26 +153,38 @@ "&& setenv dtbparam \" - ${fdt_addr_r}\" && true\0"#define SD_BOOTCMD \ -"sdargs=ip=off root=/dev/mmcblk1p2 rw,noatime rootfstype=ext4 " \ -"rootwait\0" \ -"sdboot=run setup; " \ + "sddev=1\0" \ + "sdbootpart=1\0" \ + "sdrootpart=2\0" \ + "sdfinduuid=part uuid mmc ${sddev}:${sdrootpart} uuid\0" \ + "set_sdargs=setenv sdargs ip=off root=PARTUUID=${uuid} rw,noatime " \ + "rootfstype=ext4 rootwait\0" \ +"sdboot=run setup; run sdfinduuid; run set_sdargs; " \"setenv bootargs ${defargs} ${sdargs} ${setupargs} " \"${vidargs}; echo Booting from SD card; " \ - "run sddtbload; load mmc 1:1 ${kernel_addr_r} " \ - "${boot_file} && run fdt_fixup && " \ +"run sddtbload; load mmc ${sddev}:${sdbootpart} " \ +"${kernel_addr_r} ${boot_file} && run fdt_fixup && " \"bootz ${kernel_addr_r} ${dtbparam}\0" \ -"sddtbload=setenv dtbparam; load mmc 1:1 ${fdt_addr_r} " \ - "${fdt_file} && setenv dtbparam \" - ${fdt_addr_r}\" &&true\0"
include/configs/colibri_imx6.h +8
-3+"sddtbload=setenv dtbparam; load mmc ${sddev}:${sdbootpart} " \ +"${fdt_addr_r} ${fdt_file} && setenv dtbparam \" - " \ + "${fdt_addr_r}\" && true\0"#define USB_BOOTCMD \ - "usbargs=ip=off root=/dev/sda2 rw,noatime rootfstype=ext4 " \ - "rootwait\0" \ - "usbboot=run setup; setenv bootargs ${defargs} ${setupargs} " \ + "usbdev=0\0" \ + "usbbootpart=1\0" \ + "usbrootpart=2\0" \ + "usbfinduuid=part uuid usb ${usbdev}:${usbrootpart} uuid\0" \ + "set_usbargs=setenv usbargs ip=off root=PARTUUID=${uuid}rw,noatime " \
include/configs/colibri_imx6.h +2
-0+"rootfstype=ext4 rootwait\0" \ + "usbboot=run setup; usb start; run usbfinduuid; run
set_usbargs; " \include/configs/colibri_imx6.h +1
-0+"setenv bootargs ${defargs} ${setupargs} " \ "${usbargs} ${vidargs}; echo Booting from USB stick...;" \
include/configs/colibri_imx6.h +0
-1- "usb start && run usbdtbload; load usb 0:1${kernel_addr_r} " \
include/configs/colibri_imx6.h +3
-1+"run usbdtbload; " \ +"load usb ${usbdev}:${usbbootpart} ${kernel_addr_r} " \"${boot_file} && run fdt_fixup && " \"bootz ${kernel_addr_r} ${dtbparam}\0" \ -"usbdtbload=setenv dtbparam; load usb 0:1 ${fdt_addr_r} " \ + "usbdtbload=setenv dtbparam; load usb ${usbdev}:${usbbootpart}" \
include/configs/colibri_imx6.h +1
-0+"${fdt_addr_r} " \ "${fdt_file} && setenv dtbparam \" - ${fdt_addr_r}\" &&true\0"
#define
FDT_FILE"imx6dl-colibri-eval-v3.dtb"
include/configs/colibri_imx6.h line 207
Quoted 4 lines
include/configs/colibri_imx6.h +1
-0@@ -186,6 +204,7 @@MEM_LAYOUT_ENV_SETTINGS \ NFS_BOOTCMD \SD_BOOTCMD \ +USB_BOOTCMD \
Yeah, that is a good one (;-p). Maybe you could add a note to the commit message that this indeed also fixes the legacy usbboot command. Actually, the commit message probably should mention sdboot and usbboot as well anyway.
Quoted 4 lines
include/configs/colibri_imx6.h +0
-0"setethupdate=if env exists ethaddr; then; else setenv ethaddr " \"00:14:2d:00:00:00; fi; tftpboot ${loadaddr} " \"flash_eth.img && source ${loadaddr}\0" \
Cheers
Marcel
PATCH 1/1 colibri_imx6: use UUID for rootfs
Hi Marcel,
Thanks for your comments.
Quoted 80 lines · Marcel Ziswiler
Hi Igor
Thanks for cleaning that up.
Quoted 5 lines · Igor Opaniuk
Replace usage of "
/dev/mmcblk*p*" with a proper UUID of rootfs partition.
This fixes the issue, when MMC controllers are probed in a different order
in U-boot and Linux kernel.Basically a dream come true (;-p). Looks fine and works with latest 2.8b6 as well as today's linux-next. Just a few minor comments below.
Quoted 1 line
Signed-off-by Igor Opaniuk <[email protected]>With that addressed you may add my
Tested-by Marcel Ziswiler <[email protected]>And tackle all the other boards as well.
Quoted 57 lines
--- configs/colibri_imx6_defconfig | 1 + include/configs/colibri_imx6.h | 55 +++++++++++++++++++++++--------- -- 2 files changed, 38 insertions(+), 18 deletions(-)configs/colibri_imx6_defconfig +1
-0@@ -40,6 +40,7 @@ CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y +CONFIG_CMD_UUID=y CONFIG_CMD_USB=y CONFIG_CMD_USB_SDP=y CONFIG_CMD_USB_MASS_STORAGE=yinclude/configs/colibri_imx6.h +9
-6@@ -115,16 +115,22 @@ "imx6dl-colibri-cam-eval-v3.dtb fat 0 1"#define EMMC_BOOTCMD \ -"emmcargs=ip=off root=/dev/mmcblk0p2 rw,noatime rootfstype=ext4 " \ + "emmcdev=0\0" \ + "emmcbootpart=1\0" \ + "emmcrootpart=2\0" \ + "emmcfinduuid=part uuid mmc ${mmcdev}:${emmcrootpart} uuid\0" \ + "set_emmcargs=setenv emmcargs ip=off root=PARTUUID=${uuid} "\ + "rw,noatime rootfstype=ext4 " \ "rootwait\0" \ -"emmcboot=run setup; " \ + "emmcboot=run setup; run emmcfinduuid; run set_emmcargs; " \ "setenv bootargs ${defargs} ${emmcargs} ${setupargs} " \"${vidargs}; echo Booting from internal eMMC chip...; " \ -"run emmcdtbload; load mmc 0:1 ${kernel_addr_r} " \ -"${boot_file} && run fdt_fixup && " \ +"run emmcdtbload; load mmc ${emmcdev}:${emmcbootpart} " \ +"${kernel_addr_r} ${boot_file} && run fdt_fixup && " \"bootz ${kernel_addr_r} ${dtbparam}\0" \ -"emmcdtbload=setenv dtbparam; load mmc 0:1 ${fdt_addr_r} " \ - "${fdt_file} && setenv dtbparam \" - ${fdt_addr_r}\" &&true\0"
+ "emmcdtbload=setenv dtbparam; load mmc
${emmcdev}:${emmcbootpart} " \include/configs/colibri_imx6.h +2
-0+"${fdt_addr_r} ${fdt_file} && " \ +"setenv dtbparam \" - ${fdt_addr_r}\" && true\0"
Quoted 6 lines
Quoted 2 lines
#define MEM_LAYOUT_ENV_SETTINGS \ "bootm_size=0x10000000\0" \Looks great, except I would sort that stuff alphabetically again (applies to sdboot and usbboot as well). Just makes comparing things so much easier.
This is what I actually didn't get, which particular stuff did you mean? defines?
Quoted 60 lines
Quoted 60 lines
include/configs/colibri_imx6.h +9
-7@@ -147,26 +153,38 @@ "&& setenv dtbparam \" - ${fdt_addr_r}\" && true\0"#define SD_BOOTCMD \ -"sdargs=ip=off root=/dev/mmcblk1p2 rw,noatime rootfstype=ext4 " \ -"rootwait\0" \ -"sdboot=run setup; " \ + "sddev=1\0" \ + "sdbootpart=1\0" \ + "sdrootpart=2\0" \ + "sdfinduuid=part uuid mmc ${sddev}:${sdrootpart} uuid\0" \ + "set_sdargs=setenv sdargs ip=off root=PARTUUID=${uuid} rw,noatime " \ + "rootfstype=ext4 rootwait\0" \ +"sdboot=run setup; run sdfinduuid; run set_sdargs; " \"setenv bootargs ${defargs} ${sdargs} ${setupargs} " \"${vidargs}; echo Booting from SD card; " \ - "run sddtbload; load mmc 1:1 ${kernel_addr_r} " \ - "${boot_file} && run fdt_fixup && " \ +"run sddtbload; load mmc ${sddev}:${sdbootpart} " \ +"${kernel_addr_r} ${boot_file} && run fdt_fixup && " \"bootz ${kernel_addr_r} ${dtbparam}\0" \ -"sddtbload=setenv dtbparam; load mmc 1:1 ${fdt_addr_r} " \ - "${fdt_file} && setenv dtbparam \" - ${fdt_addr_r}\" &&true\0"
include/configs/colibri_imx6.h +8
-3+"sddtbload=setenv dtbparam; load mmc ${sddev}:${sdbootpart} " \ +"${fdt_addr_r} ${fdt_file} && setenv dtbparam \" - " \ + "${fdt_addr_r}\" && true\0"#define USB_BOOTCMD \ - "usbargs=ip=off root=/dev/sda2 rw,noatime rootfstype=ext4 " \ - "rootwait\0" \ - "usbboot=run setup; setenv bootargs ${defargs} ${setupargs} " \ + "usbdev=0\0" \ + "usbbootpart=1\0" \ + "usbrootpart=2\0" \ + "usbfinduuid=part uuid usb ${usbdev}:${usbrootpart} uuid\0" \ + "set_usbargs=setenv usbargs ip=off root=PARTUUID=${uuid}rw,noatime " \
include/configs/colibri_imx6.h +2
-0+"rootfstype=ext4 rootwait\0" \ + "usbboot=run setup; usb start; run usbfinduuid; run
set_usbargs; " \+ "setenv bootargs ${defargs} ${setupargs} " \ "${usbargs} ${vidargs}; echo Booting from USB stick...;" \
- "usb start && run usbdtbload; load usb 0:1
${kernel_addr_r} " \include/configs/colibri_imx6.h +3
-1+"run usbdtbload; " \ +"load usb ${usbdev}:${usbbootpart} ${kernel_addr_r} " \"${boot_file} && run fdt_fixup && " \"bootz ${kernel_addr_r} ${dtbparam}\0" \ -"usbdtbload=setenv dtbparam; load usb 0:1 ${fdt_addr_r} " \ + "usbdtbload=setenv dtbparam; load usb ${usbdev}:${usbbootpart}" \
+ "${fdt_addr_r} " \ "${fdt_file} && setenv dtbparam \" - ${fdt_addr_r}\" &&true\0"
Quoted 11 lines
include/configs/colibri_imx6.h line 207
Quoted 6 lines
#define
FDT_FILE"imx6dl-colibri-eval-v3.dtb"include/configs/colibri_imx6.h +1
-0@@ -186,6 +204,7 @@MEM_LAYOUT_ENV_SETTINGS \ NFS_BOOTCMD \SD_BOOTCMD \ +USB_BOOTCMD \Yeah, that is a good one (;-p). Maybe you could add a note to the commit message that this indeed also fixes the legacy usbboot command. Actually, the commit message probably should mention sdboot and usbboot as well anyway.
I'll also check it with the fix from Heinrich [1], which fixes the data abort in the load command.
Quoted 6 lines
Quoted 5 lines
include/configs/colibri_imx6.h +0
-0"setethupdate=if env exists ethaddr; then; else setenv ethaddr " \"00:14:2d:00:00:00; fi; tftpboot ${loadaddr} " \"flash_eth.img && source ${loadaddr}\0" \
Quoted 7 lines
Cheers
Marcel
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
[1]: https://patchwork.ozlabs.org/patch/1082249/
Signature · 8 lines
Best regards - Freundliche Grüsse - Meilleures salutations Senior Development Engineer, Igor Opaniuk Toradex AG Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500 48 00 (main line)
PATCH 1/1 colibri_imx6: use UUID for rootfs
Hi Igor
Quoted 106 lines · Igor Opaniuk
Hi Marcel,
Thanks for your comments.
Quoted 92 lines · Marcel Ziswiler
Hi Igor
Thanks for cleaning that up.
Quoted 6 lines · Igor Opaniuk
Replace usage of "
/dev/mmcblk*p*" with a proper UUID of rootfs partition.
This fixes the issue, when MMC controllers are probed in a different
order
in U-boot and Linux kernel.Basically a dream come true (;-p). Looks fine and works with latest 2.8b6 as well as today's linux-next. Just a few minor comments below.
Quoted 1 line
Signed-off-by Igor Opaniuk <[email protected]>With that addressed you may add my
Tested-by Marcel Ziswiler <[email protected]>And tackle all the other boards as well.
Quoted 68 lines
--- configs/colibri_imx6_defconfig | 1 + include/configs/colibri_imx6.h | 55 +++++++++++++++++++++++----- ---- -- 2 files changed, 38 insertions(+), 18 deletions(-)configs/colibri_imx6_defconfig +1
-0@@ -40,6 +40,7 @@ CONFIG_CMD_GPIO=y CONFIG_CMD_GPT=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y +CONFIG_CMD_UUID=y CONFIG_CMD_USB=y CONFIG_CMD_USB_SDP=y CONFIG_CMD_USB_MASS_STORAGE=yinclude/configs/colibri_imx6.h +0
-1@@ -115,16 +115,22 @@"imx6dl-colibri-cam-eval-v3.dtb fat 0 1" #define EMMC_BOOTCMD \ - "emmcargs=ip=off root=/dev/mmcblk0p2 rw,noatimerootfstype=ext4
" \include/configs/colibri_imx6.h +4
-0+"emmcdev=0\0" \ +"emmcbootpart=1\0" \ +"emmcrootpart=2\0" \ + "emmcfinduuid=part uuid mmc ${mmcdev}:${emmcrootpart}uuid\0" \
+ "set_emmcargs=setenv emmcargs ip=off root=PARTUUID=${uuid}
"\include/configs/colibri_imx6.h +2
-1+"rw,noatime rootfstype=ext4 " \"rootwait\0" \ -"emmcboot=run setup; " \ +"emmcboot=run setup; run emmcfinduuid; run set_emmcargs; " \ "setenv bootargs ${defargs} ${emmcargs} ${setupargs} " \ "${vidargs}; echo Booting from internal eMMC chip...; " \include/configs/colibri_imx6.h +1
-2-"run emmcdtbload; load mmc 0:1 ${kernel_addr_r} " \ -"${boot_file} && run fdt_fixup && " \ + "run emmcdtbload; load mmc${emmcdev}:${emmcbootpart} "
\
+ "${kernel_addr_r} ${boot_file} && runfdt_fixup&&" \ "bootz ${kernel_addr_r} ${dtbparam}\0" \- "emmcdtbload=setenv dtbparam; load mmc 0:1 ${fdt_addr_r} "
\
- "${fdt_file} && setenv dtbparam \" -
${fdt_addr_r}\" &&
true\0"
+ "emmcdtbload=setenv dtbparam; load mmc
${emmcdev}:${emmcbootpart} " \include/configs/colibri_imx6.h +2
-0+"${fdt_addr_r} ${fdt_file} && " \ +"setenv dtbparam \" - ${fdt_addr_r}\" && true\0" Quoted 7 lines
Quoted 2 lines
#define MEM_LAYOUT_ENV_SETTINGS \ "bootm_size=0x10000000\0" \Looks great, except I would sort that stuff alphabetically again (applies to sdboot and usbboot as well). Just makes comparing things so
much easier.
Quoted 2 lines
This is what I actually didn't get, which particular stuff did you mean? defines?
Well, yes. But also e.g. emmcbootpart coming before emmcdev etc.
Quoted 86 lines
Quoted 72 lines
Quoted 72 lines
include/configs/colibri_imx6.h +0
-1@@ -147,26 +153,38 @@"&& setenv dtbparam \" - ${fdt_addr_r}\" && true\0" #define SD_BOOTCMD \ - "sdargs=ip=off root=/dev/mmcblk1p2 rw,noatimerootfstype=ext4 "
\include/configs/colibri_imx6.h +5
-2-"rootwait\0" \ -"sdboot=run setup; " \ +"sddev=1\0" \ +"sdbootpart=1\0" \ +"sdrootpart=2\0" \ +"sdfinduuid=part uuid mmc ${sddev}:${sdrootpart} uuid\0" \ + "set_sdargs=setenv sdargs ip=off root=PARTUUID=${uuid}rw,noatime " \
include/configs/colibri_imx6.h +2
-0+"rootfstype=ext4 rootwait\0" \ +"sdboot=run setup; run sdfinduuid; run set_sdargs; " \ "setenv bootargs ${defargs} ${sdargs} ${setupargs}" \ "${vidargs}; echo Booting from SD card; " \include/configs/colibri_imx6.h +2
-2-"run sddtbload; load mmc 1:1 ${kernel_addr_r} " \ -"${boot_file} && run fdt_fixup && " \ +"run sddtbload; load mmc ${sddev}:${sdbootpart} " \ + "${kernel_addr_r} ${boot_file} && run fdt_fixup &&" \ "bootz ${kernel_addr_r} ${dtbparam}\0" \include/configs/colibri_imx6.h +0
-2-"sddtbload=setenv dtbparam; load mmc 1:1 ${fdt_addr_r} " \ - "${fdt_file} && setenv dtbparam \" -${fdt_addr_r}\" &&
true\0"
+ "sddtbload=setenv dtbparam; load mmc ${sddev}:${sdbootpart}
" \
+ "${fdt_addr_r} ${fdt_file} && setenv dtbparam \" -
" \include/configs/colibri_imx6.h +1
-1+"${fdt_addr_r}\" && true\0" #define USB_BOOTCMD \ - "usbargs=ip=off root=/dev/sda2 rw,noatime rootfstype=ext4 "\
include/configs/colibri_imx6.h +0
-2-"rootwait\0" \ - "usbboot=run setup; setenv bootargs ${defargs} ${setupargs}" \
include/configs/colibri_imx6.h +4
-0+"usbdev=0\0" \ +"usbbootpart=1\0" \ +"usbrootpart=2\0" \ +"usbfinduuid=part uuid usb ${usbdev}:${usbrootpart} uuid\0" \
+ "set_usbargs=setenv usbargs ip=off root=PARTUUID=${uuid}
rw,noatime " \include/configs/colibri_imx6.h +2
-0+"rootfstype=ext4 rootwait\0" \ + "usbboot=run setup; usb start; run usbfinduuid; run
set_usbargs; " \+ "setenv bootargs ${defargs} ${setupargs} " \ "${usbargs} ${vidargs}; echo Booting from USBstick...;
" \
- "usb start && run usbdtbload; load usb 0:1
${kernel_addr_r} " \include/configs/colibri_imx6.h +2
-0+"run usbdtbload; " \ + "load usb ${usbdev}:${usbbootpart} ${kernel_addr_r}" \ "${boot_file} && run fdt_fixup && " \ "bootz ${kernel_addr_r} ${dtbparam}\0" \include/configs/colibri_imx6.h +1
-1-"usbdtbload=setenv dtbparam; load usb 0:1 ${fdt_addr_r} " \ + "usbdtbload=setenv dtbparam; load usb${usbdev}:${usbbootpart}
" \+ "${fdt_addr_r} " \ "${fdt_file} && setenv dtbparam \" -${fdt_addr_r}\" &&
true\0"Quoted 13 lines
include/configs/colibri_imx6.h line 207
Quoted 6 lines
#define
FDT_FILE"imx6dl-colibri-eval-v3.dtb"include/configs/colibri_imx6.h +1
-0@@ -186,6 +204,7 @@MEM_LAYOUT_ENV_SETTINGS \ NFS_BOOTCMD \SD_BOOTCMD \ +USB_BOOTCMD \Yeah, that is a good one (;-p). Maybe you could add a note to the commit message that this indeed also fixes the legacy usbboot command.
Actually, the commit message probably should mention sdboot and usbboot
as well anyway.
Quoted 2 lines
I'll also check it with the fix from Heinrich [1], which fixes the data abort in the load command.
Yeah, I manually just used fatload but that would not work e.g. if the media is formatted with a file system other than FAT.
Quoted 8 lines
Quoted 8 lines
Quoted 5 lines
include/configs/colibri_imx6.h +0
-0"setethupdate=if env exists ethaddr; then; else setenvethaddr
" \ "00:14:2d:00:00:00; fi; tftpboot ${loadaddr} " \ "flash_eth.img && source ${loadaddr}\0" \Cheers
Quoted 13 lines
Quoted 5 lines
Marcel
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot[1]: https://patchwork.ozlabs.org/patch/1082249/
Signature · 4 lines
Best regards - Freundliche Grüsse - Meilleures salutations Senior Development Engineer, Igor Opaniuk
Best regards - Mit freundlichen Grüssen - Meilleures salutations
Marcel Ziswiler
Platform Manager Embedded Linux
Toradex AG
Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500 48 00 (main line) | Direct: +41 41 500 48 10