Add support for ARRI FPGA configuration
Subsystems (3)
v4 cover Add support for ARRI FPGA configuration
This series adds drivers and FPGA manager support required for FT232H based ARRI FPGA configuration adapters.
Patch 1/3 adds FT232H interface driver (for ARRI USB PIDs) implementing commonly used FTDI USB transfer operations and ACBUS/MPSSE GPIO controllers. Depending on USB PIDs it creates platform devices for MPSSE SPI bus with attached SPI slaves or platform devices for ARRI FPP FPGA manager.
Patch 2/3 adds MPSSE SPI controller driver which registers an FTDI USB-SPI bus with attached SPI slaves from description in platform data, so existing SPI protocol drivers can be used for these slave devices (in our case altera-ps-spi). Via interface driver in patch 1/3 it is easily possible to add support for other slave devices using custom USB PIDs (e.g. spi-nor flash W25Q32 with m25p80 driver has beed used for testing MPSSE SPI controller driver).
Patch 3/3 adds FPGA manager driver for ARRI FPP adapters for FPGA configuration via Altera fast passive parallel interface.
Changes since v3:
Patch 1/3
- rebase on v5.0-rc7
- add depends on GPIOLIB to Kconfig to fix build errors
- fix build errors due to removed devm_gpiochip_remove() (replace by gpiochip_remove())
Patch 2/3
- rebase on v5.0-rc7
Patch 3/3
- update Date/Version in sysfs-driver-ftdi-fifo-fpp
Changes since v2:
Patch 1/3
- use unsigned type for baudrate and clk divider calculation (don't mix signed/unsigned types)
- switch to unsigned int for 'encoded_divisor'
- use DIV_ROUND_CLOSEST() in ftdi_to_clkbits()
- update error messages in ftdi_convert_baudrate()
- update return code check of ftdi_to_clkbits()
- fix boolconv coccinelle warning
- add and use macro for MPSSE GPIOs number
- update struct mpsse_spi_platform_data to drop pin description fields and add mpsse_spi_dev_data struct instead. This allows easier pin description and init for multiple SPI devices with multiple control pins. Pass pin description via platform_data of spi_bus_info for esier IO pin init code in MPSSE driver. Update spi_board_info table accordingly
- keep Makefile entry sorted
Patch 2/3
- keep Makefile entry sorted
- make the entire comment block a C++ one
- don't use magic number for the size of the lookup table
- use sizeof() instead of magic number for the buffer size
- rework gpio chip select function to use it as .set_cs()
- convert to use transfer_one instead of transfer_one_message
- update dev_*() to use MPSSE platform device prefix
- s/spi_master/spi_controller
- use u16 for chip_select vars and update dev_dbg format
- use unsigned type for index vars
- reduce arguments number for ftdi_spi_tx()/ftdi_spi_rx()
- fix ftdi_spi_tx() to send all buffer data correctly even if the USB driver signals transfer of less data than requested
- update ftdi_spi_init_io() to differentiate between platform data for devices using MPSSE I/O pins and other SPI devices (e.g. using flash_platform_data, mmc_spi_platform_data, etc.). This makes the driver more generic and allows using multiple SPI slaves on the MPSSE bus
- reduce !xfer->len checks
Patch 3/3
fix 'specified bound 8 equals destination size' gcc 8 warning
Changes since v1:
Patch 1/3
- add myself as a maintainer for these drivers
- update copyright line to include 2018
- include required linux headers
- fix gcc 7.3.0 build warnings -Wunused-const-variable=
- make ftdi functions and spi_board_info struct static
- use KBUILD_MODNAME in drivers struct
- use dev_err() for error messages instead of dev_info()
- drop not needed output about number of used MPSSE pins since it is constant (not configurable)
- remove ftdi function prototypes from header ft232h-intf.h as these are not exported anymore
- update comments (don't use kernel-doc format as we do not export symbols anymore and functions are "static")
Patch 2/3
- fix build breakage when building with ARCH=i386 allmodconfig
- add checks for ops->lock/ops->unlock presence in pdata
- update copyright line to include 2018
- remove printing numbers in parentheses (%d)
Patch 3/3
- update copyright line to include 2018
- add sysfs ABI documentation
Changes since initial version (MFD based):
- don't use MFD framework
- don't use original FT232H USB PID (it is too generic and collides with existing ftdi_sio driver)
- don't add separate CBUS GPIO driver based on FT232H MFD device
- redesign/rework the drivers as described under [4]
- add basic FT232H interface driver under drivers/usb/misc/
- use custom reserved USB PIDs in the USB driver for adapter devices
- add notes about borrowed protocol code from libftdi to commit log and header file
- add MPSSE SPI controller driver supporting USB-SPI bus with dynamically added SPI slaves from description in platform data (the initial attempt didn't include USB SPI bus support for PS- SPI FPGA configuration via USB)
- rework FPP fpga manager driver based on new FT232H interface driver and extend it according to CPLD changes for additional support of new hardware revision B.
Anatolij Gustschin (3):
usb: misc: add driver for FT232H based FPGA configuration devices
spi: add FTDI MPSSE SPI controller driver
fpga: Add fpga manager driver for ARRI Altera FPP
.../ABI/testing/sysfs-driver-ftdi-fifo-fpp | 7 + MAINTAINERS | 8 + drivers/fpga/Kconfig | 7 + drivers/fpga/Makefile | 1 + drivers/fpga/ftdi-fifo-fpp.c | 594 +++++++ drivers/spi/Kconfig | 7 + drivers/spi/Makefile | 1 + drivers/spi/spi-ftdi-mpsse.c | 651 ++++++++ drivers/usb/misc/Kconfig | 10 + drivers/usb/misc/Makefile | 1 + drivers/usb/misc/ft232h-intf.c | 1467 +++++++++++++++++ include/linux/usb/ft232h-intf.h | 206 +++ 12 files changed, 2960 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-driver-ftdi-fifo-fpp create mode 100644 drivers/fpga/ftdi-fifo-fpp.c create mode 100644 drivers/spi/spi-ftdi-mpsse.c create mode 100644 drivers/usb/misc/ft232h-intf.c create mode 100644 include/linux/usb/ft232h-intf.h
Signature · 1 line
2.17.1
PATCH v4 1/3 usb: misc: add driver for FT232H based FPGA configuration devices
Add USB interface driver for ARRI FPGA configuration devices based on FTDI FT232H chip. Depending on USB PID the driver registers different platform devices describing an FPGA configuration interface.
One FPGA configuration interface type is the usual SPI bus with additional control and status GPIOs. For this interface type the FTDI MPSSE mode is utilized to support SPI bus and GPIO-L/H pins for SPI bus chipselect and SPI slave device I/O. Subsequent patch adds an MPSSE SPI controller driver for USB-SPI bus support. The actual FPGA configuration driver for SPI bus is already available in the FPGA manager framework (altera-ps-spi module).
Another FPGA configuration interface type is the FT245 FIFO (connected via CPLD) with additional control and status GPIOs on FT232H ACBUS. This interface is used to configure FPGAs using Altera fast passive parallel (FPP) interface. Subsequent patch will add an FPP FPGA manager driver for it.
The FTDI protocol code and prototypes was borrowed from libftdi.
--- MAINTAINERS | 8 + drivers/usb/misc/Kconfig | 10 + drivers/usb/misc/Makefile | 1 + drivers/usb/misc/ft232h-intf.c | 1467 +++++++++++++++++++++++++++++++ include/linux/usb/ft232h-intf.h | 206 +++++ 5 files changed, 1692 insertions(+) create mode 100644 drivers/usb/misc/ft232h-intf.c create mode 100644 include/linux/usb/ft232h-intf.h
MAINTAINERS +8 -0
@@ -15968,6 +15968,14 @@ S: Maintained F: Documentation/usb/acm.txt F: drivers/usb/class/cdc-acm.* +USB ARRI FPGA CONFIGURATION ADAPTER DRIVER +M: Anatolij Gustschin <[email protected]> +L: [email protected] +S: Maintained +F: drivers/usb/misc/ft232h-intf.c +F: drivers/spi/spi-ftdi-mpsse.c +F: include/linux/usb/ft232h-intf.h + USB AR5523 WIRELESS DRIVER M: Pontus Fuchs <[email protected]> L: [email protected]
drivers/usb/misc/Kconfig +10 -0
@@ -276,3 +276,13 @@ config USB_CHAOSKEY To compile this driver as a module, choose M here: the module will be called chaoskey. + +config USB_FT232H_INTF + tristate "FTDI FT232H FPGA configuration interface driver" + depends on GPIOLIB + help + Enable driver support for the FT232H based USB-GPIO/SPI/FIFO + interface adapter for FPGA configuration. Additional drivers + such as spi-ftdi-mpsse, altera-ps-spi, ftdi-fifo-fpp and + fpga-mgr must be enabled in order to use the functionality of + the device.
drivers/usb/misc/Makefile +1 -0
@@ -10,6 +10,7 @@ obj-$(CONFIG_USB_CYTHERM) += cytherm.o obj-$(CONFIG_USB_EMI26) += emi26.o obj-$(CONFIG_USB_EMI62) += emi62.o obj-$(CONFIG_USB_EZUSB_FX2) += ezusb.o +obj-$(CONFIG_USB_FT232H_INTF) += ft232h-intf.o obj-$(CONFIG_USB_FTDI_ELAN) += ftdi-elan.o obj-$(CONFIG_USB_IDMOUSE) += idmouse.o obj-$(CONFIG_USB_IOWARRIOR) += iowarrior.o
drivers/usb/misc/ft232h-intf.c new file +1467 -0
1,467 lines not on this page · raw message
include/linux/usb/ft232h-intf.h new file +206 -0
206 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v4 2/3 spi: add FTDI MPSSE SPI controller driver
In reply to Anatolij GustschinAdd SPI bus controller driver for FTDI MPSSE mode. This driver is supposed to be used together with the FT232H interface driver for FPGA configuration in drivers/usb/misc/ft232h-intf.c which adds an mpsse spi platform device describing USB SPI bus with attached SPI slave devices.
--- drivers/spi/Kconfig | 7 + drivers/spi/Makefile | 1 + drivers/spi/spi-ftdi-mpsse.c | 651 +++++++++++++++++++++++++++++++++++ 3 files changed, 659 insertions(+) create mode 100644 drivers/spi/spi-ftdi-mpsse.c
drivers/spi/Kconfig +7 -0
@@ -289,6 +289,13 @@ config SPI_NXP_FLEXSPI This controller does not support generic SPI messages and only supports the high-level SPI memory interface. +config SPI_FTDI_MPSSE + tristate "FTDI MPSSE SPI controller" + depends on USB_FT232H_INTF || COMPILE_TEST + help + FT232H supports SPI in MPSSE mode. This driver provides MPSSE + SPI controller in master mode. + config SPI_GPIO tristate "GPIO-based bitbanging SPI Master" depends on GPIOLIB || COMPILE_TEST
drivers/spi/Makefile +1 -0
@@ -47,6 +47,7 @@ obj-$(CONFIG_SPI_FSL_ESPI) += spi-fsl-espi.o obj-$(CONFIG_SPI_FSL_LPSPI) += spi-fsl-lpspi.o obj-$(CONFIG_SPI_FSL_QUADSPI) += spi-fsl-qspi.o obj-$(CONFIG_SPI_FSL_SPI) += spi-fsl-spi.o +obj-$(CONFIG_SPI_FTDI_MPSSE) += spi-ftdi-mpsse.o obj-$(CONFIG_SPI_GPIO) += spi-gpio.o obj-$(CONFIG_SPI_IMG_SPFI) += spi-img-spfi.o obj-$(CONFIG_SPI_IMX) += spi-imx.o
drivers/spi/spi-ftdi-mpsse.c new file +651 -0
651 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v4 3/3 fpga: Add fpga manager driver for ARRI Altera FPP
In reply to Anatolij GustschinAdd FPGA manager driver for loading ARRI Altera FPGAs via fast passive parallel (FPP) interface using FTDI FT232H chip.
--- .../ABI/testing/sysfs-driver-ftdi-fifo-fpp | 7 + drivers/fpga/Kconfig | 7 + drivers/fpga/Makefile | 1 + drivers/fpga/ftdi-fifo-fpp.c | 594 ++++++++++++++++++ 4 files changed, 609 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-driver-ftdi-fifo-fpp create mode 100644 drivers/fpga/ftdi-fifo-fpp.c
Documentation/ABI/testing/sysfs-driver-ftdi-fifo-fpp new file +7 -0
@@ -0,0 +1,7 @@ +What: /sys/bus/platform/devices/ftdi-fifo-fpp-mgr.N/cfg_mode +Date: Feb 2019 +Kernel Version: 5.2 +Contact: Anatolij Gustschin <[email protected]> +Description: + Contains either "fifo" or "bitbang" and controls if fifo + of bitbang configuration mode is used in the driver.
drivers/fpga/Kconfig +7 -0
@@ -50,6 +50,13 @@ config FPGA_MGR_ALTERA_CVP FPGA manager driver support for Arria-V, Cyclone-V, Stratix-V and Arria 10 Altera FPGAs using the CvP interface over PCIe. +config FPGA_MGR_FTDI_FIFO_FPP + tristate "Altera FPP over FT232H FIFO" + depends on USB_FT232H_INTF + help + FPGA manager driver support for Altera fast passive parallel + interface (FPP) over FT232H FT245 FIFO. + config FPGA_MGR_ZYNQ_FPGA tristate "Xilinx Zynq FPGA" depends on ARCH_ZYNQ || COMPILE_TEST
drivers/fpga/Makefile +1 -0
@@ -9,6 +9,7 @@ obj-$(CONFIG_FPGA) += fpga-mgr.o # FPGA Manager Drivers obj-$(CONFIG_FPGA_MGR_ALTERA_CVP) += altera-cvp.o obj-$(CONFIG_FPGA_MGR_ALTERA_PS_SPI) += altera-ps-spi.o +obj-$(CONFIG_FPGA_MGR_FTDI_FIFO_FPP) += ftdi-fifo-fpp.o obj-$(CONFIG_FPGA_MGR_ICE40_SPI) += ice40-spi.o obj-$(CONFIG_FPGA_MGR_MACHXO2_SPI) += machxo2-spi.o obj-$(CONFIG_FPGA_MGR_SOCFPGA) += socfpga.o
drivers/fpga/ftdi-fifo-fpp.c new file +594 -0
594 lines not on this page · raw message
Signature · 1 line
2.17.1
Re: [PATCH v4 3/3] fpga: Add fpga manager driver for ARRI Altera FPP
Hi,
On Thu, 21 Feb 2019 21:25:06 +0100
Anatolij Gustschin [email protected] wrote:
...
Quoted 7 lines
.../ABI/testing/sysfs-driver-ftdi-fifo-fpp | 7 + drivers/fpga/Kconfig | 7 + drivers/fpga/Makefile | 1 + drivers/fpga/ftdi-fifo-fpp.c | 594 ++++++++++++++++++ 4 files changed, 609 insertions(+)create mode 100644
Documentation/ABI/testing/sysfs-driver-ftdi-fifo-fppcreate mode 100644drivers/fpga/ftdi-fifo-fpp.c
Ping. Any comments to this driver?
Thanks,
Anatolij
Moritz Fischer
maintainerRe: [PATCH v4 3/3] fpga: Add fpga manager driver for ARRI Altera FPP
In reply to Anatolij GustschinHi Anatolij,
looks mostly good, a couple of nits inline.
Quoted 62 lines · Anatolij Gustschin
Add FPGA manager driver for loading ARRI Altera FPGAs via fast passive parallel (FPP) interface using FTDI FT232H chip.
Signed-off-by Anatolij Gustschin <[email protected]>--- .../ABI/testing/sysfs-driver-ftdi-fifo-fpp | 7 + drivers/fpga/Kconfig | 7 + drivers/fpga/Makefile | 1 + drivers/fpga/ftdi-fifo-fpp.c | 594 ++++++++++++++++++ 4 files changed, 609 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-driver-ftdi-fifo-fpp create mode 100644 drivers/fpga/ftdi-fifo-fpp.cDocumentation/ABI/testing/sysfs-driver-ftdi-fifo-fpp new file +7
-0@@ -0,0 +1,7 @@ +What: /sys/bus/platform/devices/ftdi-fifo-fpp-mgr.N/cfg_mode +Date: Feb 2019 +Kernel Version: 5.2 +Contact: Anatolij Gustschin <[email protected]> +Description: + Contains either "fifo" or "bitbang" and controls if fifo + of bitbang configuration mode is used in the driver.drivers/fpga/Kconfig +7
-0@@ -50,6 +50,13 @@ config FPGA_MGR_ALTERA_CVP FPGA manager driver support for Arria-V, Cyclone-V, Stratix-V and Arria 10 Altera FPGAs using the CvP interface over PCIe. +config FPGA_MGR_FTDI_FIFO_FPP + tristate "Altera FPP over FT232H FIFO" + depends on USB_FT232H_INTF + help + FPGA manager driver support for Altera fast passive parallel + interface (FPP) over FT232H FT245 FIFO. + config FPGA_MGR_ZYNQ_FPGA tristate "Xilinx Zynq FPGA" depends on ARCH_ZYNQ || COMPILE_TESTdrivers/fpga/Makefile +1
-0@@ -9,6 +9,7 @@ obj-$(CONFIG_FPGA) += fpga-mgr.o # FPGA Manager Drivers obj-$(CONFIG_FPGA_MGR_ALTERA_CVP) += altera-cvp.o obj-$(CONFIG_FPGA_MGR_ALTERA_PS_SPI) += altera-ps-spi.o +obj-$(CONFIG_FPGA_MGR_FTDI_FIFO_FPP) += ftdi-fifo-fpp.o obj-$(CONFIG_FPGA_MGR_ICE40_SPI) += ice40-spi.o obj-$(CONFIG_FPGA_MGR_MACHXO2_SPI) += machxo2-spi.o obj-$(CONFIG_FPGA_MGR_SOCFPGA) += socfpga.odrivers/fpga/ftdi-fifo-fpp.c new file +0
-0
drivers/fpga/ftdi-fifo-fpp.c line 5
Quoted 5 lines
drivers/fpga/ftdi-fifo-fpp.c new file +5
-0@@ -0,0 +1,594 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* Altera FPGA firmware upload via FPP using FT232H Bitbang/FT245-FIFO. +* +* Copyright (C) 2017 - 2018 DENX Software Engineering
Maybe bump that to 2019 ;-)
Quoted 77 lines
drivers/fpga/ftdi-fifo-fpp.c new file +77
-0+* Anatolij Gustschin <[email protected]> +*/ + +#include <linux/bitops.h> +#include <linux/delay.h> +#include <linux/fpga/fpga-mgr.h> +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/sizes.h> +#include <linux/slab.h> +#include <linux/gpio/consumer.h> +#include <linux/platform_device.h> +#include <linux/usb.h> +#include <linux/usb/ft232h-intf.h> + +#define BULK_OUT_BUF_SZ SZ_1M +#define MAX_RETRIES 10 + +/* +* With logic of CPLD we can write the state of nConfig pin and +* read back the state of some pins (conf_done, init_done, nStatus). +* Status header and bit assignment in data register on CPLD. +*/ +#define INPUT_HEADER_0 0xA5 +#define INPUT_HEADER_1 0x5A +#define IN_CONF_DONE BIT(0) +#define IN_INIT_DONE BIT(1) +#define IN_ADDR_SELECT BIT(4) +#define IN_BOARD_REV BIT(5) +#define OUT_NCONFIG BIT(0) +#define OUT_RESET_N BIT(1) + +enum fpp_board_rev { +BOARD_REVA =1 , +BOARD_REVB =2 , +}; + +enum fpp_addr_sel { +ADDR_SELECT_INVALID , +ADDR_SELECT_GND , +ADDR_SELECT_NC +}; + +struct fpp_mgr_ops { +int (*write_init)(struct fpga_manager *mgr, +struct fpga_image_info *info, +const char *buf,size_t count); +int (*write)(struct fpga_manager *mgr,const char *buf,size_t count); +int (*write_complete)(struct fpga_manager *mgr, +struct fpga_image_info *info); +}; + +struct fpp_fpga_mgr_priv { +struct platform_device *pdev; +struct usb_interface *intf; +const struct ft232h_intf_ops *iops; +struct fpga_manager *mgr; +struct fpp_mgr_ops *ops; +struct gpio_desc *nconfig; +struct gpio_desc *conf_done; +char cfg_mode[8 ]; +u8 out_data_port; +int index; +void *bulk_buf; +char usb_dev_id[32 ]; +char fpga_mgr_name[64 ]; +enum fpp_board_rev rev; +enum fpp_addr_sel addr_sel; +}; + +static int fpp_fpga_mgr_set_data_port (struct fpp_fpga_mgr_priv *priv, +u8 bitmask,u8 value) +{ +struct device *dev = &priv->pdev->dev; +struct bulk_desc desc; +u8 *data; +int ret;
drivers/fpga/ftdi-fifo-fpp.c line 92
Quoted 10 lines
drivers/fpga/ftdi-fifo-fpp.c new file +10
-0+ +/* +* With CPLD connected (in FT245 FIFO mode) we use ACBUS8&9 +* pins to switch between data and command mode: +* ACBUS8&9 == 0, 0 --> normal mode (data communication) +* ACBUS8&9 == 1, 0 --> command mode +*/ +gpiod_set_raw_value_cansleep (priv->nconfig,1 ); +gpiod_set_raw_value_cansleep (priv->conf_done,0 ); +msleep (50 );
You could use a constant here for the 50 ...
Quoted 17 lines
drivers/fpga/ftdi-fifo-fpp.c new file +17
-0+ +/* Write commands to CPLD */ + ret = priv->iops->set_bitmode (priv->intf,0x00 ,BITMODE_SYNCFF ); +if (ret) +return ret; + +if (value) + priv->out_data_port |= bitmask; +else + priv->out_data_port &= ~bitmask; + + data = priv->bulk_buf; + *data = priv->out_data_port; + + desc.dir_out = true; + desc.act_len =0 ; + desc.len =1 ;
drivers/fpga/ftdi-fifo-fpp.c line 119
Quoted 10 lines
drivers/fpga/ftdi-fifo-fpp.c new file +10
-0+ desc.data = data; + desc.timeout =FTDI_USB_WRITE_TIMEOUT ; + + ret = priv->iops->bulk_xfer (priv->intf, &desc); +if (ret) { +dev_err (dev,"Writing in SYNCFF mode failed: %d\n" , ret); +return ret; + } + +msleep (50 );
and here ...
drivers/fpga/ftdi-fifo-fpp.c line 123
Quoted 4 lines
drivers/fpga/ftdi-fifo-fpp.c new file +4
-0+/* Switch back to data mode with ACBUS8&9 back to low */ +gpiod_set_raw_value_cansleep (priv->nconfig,0 ); +gpiod_set_raw_value_cansleep (priv->conf_done,0 ); +msleep (50 );
and here ...
Quoted 5 lines
drivers/fpga/ftdi-fifo-fpp.c new file +5
-0+ +return 0 ; +} + +static int fpp_fpga_mgr_bitbang_write_init(struct fpga_manager *mgr,
drivers/fpga/ftdi-fifo-fpp.c line 138
Quoted 10 lines
drivers/fpga/ftdi-fifo-fpp.c new file +10
-0+struct fpga_image_info *info, + const char *buf, size_t count) +{ + struct fpp_fpga_mgr_priv *priv = mgr->priv; +struct device *dev = &priv->pdev->dev; +int retries =MAX_RETRIES ; +int ret; + +gpiod_set_value_cansleep (priv->nconfig,0 ); +msleep (50 );
and here ...
drivers/fpga/ftdi-fifo-fpp.c line 140
Quoted 2 lines
drivers/fpga/ftdi-fifo-fpp.c new file +2
-0+gpiod_set_value_cansleep (priv->nconfig,1 ); +msleep (50 );
and here ...
drivers/fpga/ftdi-fifo-fpp.c line 143
Quoted 3 lines
drivers/fpga/ftdi-fifo-fpp.c new file +3
-0+gpiod_set_value_cansleep (priv->nconfig,0 ); + +/* Wait for CONF_DONE to get low */
Does the retry number come from datasheet?
Quoted 66 lines
drivers/fpga/ftdi-fifo-fpp.c new file +66
-0+do { +msleep (50 ); + + ret =gpiod_get_value_cansleep (priv->conf_done); +if (ret <0 ) { +dev_err (dev,"Failed to get CONF_DONE pin: %d\n" , ret); +return ret; + } + +if (!ret) +break ; + }while (--retries >0 ); + +if (!retries) { +dev_warn (dev,"CONF_DONE low wait timeout\n" ); +return -ETIMEDOUT ; + } + + ret = priv->iops->set_bitmode (priv->intf,0xff ,BITMODE_BITBANG ); +if (ret <0 ) +return ret; + +/* Set max. working baud rate (for hardware without CPLD) */ +return priv->iops->set_baudrate (priv->intf,700000 ); +} + +static int fpp_fpga_mgr_bitbang_write (struct fpga_manager *mgr, +const char *buf,size_t count) +{ +struct fpp_fpga_mgr_priv *priv = mgr->priv; +struct bulk_desc desc; +size_t blk_sz; +int ret; + + desc.data = priv->bulk_buf; + desc.dir_out = true; + desc.timeout =FTDI_USB_WRITE_TIMEOUT ; + +while (count) { + blk_sz =min_t (size_t, count,BULK_OUT_BUF_SZ ); +memcpy (priv->bulk_buf, buf, blk_sz); + desc.act_len =0 ; + desc.len = blk_sz; + ret = priv->iops->bulk_xfer (priv->intf, &desc); +if (ret <0 ) +return ret; + + buf += desc.act_len; + count -= desc.act_len; + } + +return 0 ; +} + +static int fpp_fpga_mgr_bitbang_write_complete (struct fpga_manager *mgr, +struct fpga_image_info *info) +{ +struct fpp_fpga_mgr_priv *priv = mgr->priv; +struct device *dev = &priv->pdev->dev; +int retries =MAX_RETRIES ; +int ret; + +/* Wait for CONF_DONE to get high */ + do { + msleep(50); +
drivers/fpga/ftdi-fifo-fpp.c line 219
Quoted 10 lines
drivers/fpga/ftdi-fifo-fpp.c new file +10
-0+ ret =gpiod_get_value_cansleep (priv->conf_done); +if (ret <0 ) +return ret; + +if (ret) +break ; + }while (--retries >0 ); + +if (!retries) { +dev_warn (dev,"CONF_DONE wait timeout\n" );
warn or err?
Quoted 95 lines
drivers/fpga/ftdi-fifo-fpp.c new file +95
-0+return -ETIMEDOUT ; + } + + priv->iops->disable_bitbang (priv->intf); +return 0 ; +} + +static inline bool status_hdr_is_valid (u8 *buf) +{ +return buf[0 ] ==INPUT_HEADER_0 && buf[1 ] ==INPUT_HEADER_1 ; +} + +static int fpp_fpga_mgr_read_status (struct fpp_fpga_mgr_priv *priv,u8 *status) +{ +struct device *dev = &priv->pdev->dev; +u8 *inbuf = priv->bulk_buf; +int retries =MAX_RETRIES ; +int ret; + +if (!status) +return -EINVAL ; + +/* Wait until CPLD sends valid header and status register */ +do { + ret = priv->iops->read_data (priv->intf, inbuf,64 ); +if (ret <0 ) { +dev_err (dev,"Can't read status data: %d\n" , ret); +return ret; + } + +/* Check input buffer header */ +if (ret >=4 &&status_hdr_is_valid (inbuf)) { + *status = inbuf[2 ]; +return 0 ; + } + +/* Wait and read back status again */ +msleep (100 );/* CPLD sends status every 100ms */ + }while (--retries >0 ); + +dev_warn (dev,"Timeout when reading status\n" ); +return -ETIMEDOUT ; +} + +static int fpp_fpga_mgr_ft245_fifo_write_init (struct fpga_manager *mgr, +struct fpga_image_info *info, +const char *buf,size_t count) +{ +struct fpp_fpga_mgr_priv *priv = mgr->priv; +struct device *dev = &priv->pdev->dev; +int retries =MAX_RETRIES ; +int ret; +u8 status; + +gpiod_direction_output_raw (priv->conf_done,0 ); + +/* Set/reset nConfig via commands to CPLD */ + ret =fpp_fpga_mgr_set_data_port (priv,OUT_NCONFIG ,1 ); +if (ret) +return ret; + ret =fpp_fpga_mgr_set_data_port (priv,OUT_NCONFIG ,0 ); +if (ret) +return ret; + ret =fpp_fpga_mgr_set_data_port (priv,OUT_NCONFIG ,1 ); +if (ret) +return ret; + +/* In FT245 FIFO mode we need sync FIFO mode to talk to FPGA */ + ret = priv->iops->set_bitmode (priv->intf,0xff ,BITMODE_SYNCFF ); +if (ret) +return ret; + +/* Wait until FPGA is ready for loading (conf_done zero) or timeout */ +do { + ret =fpp_fpga_mgr_read_status (priv, &status); +if (!ret) { +/* Check conf_done status */ +if ((status &IN_CONF_DONE ) ==0 ) +break ; + } + }while (--retries >0 ); + +if (!retries) { +dev_warn (dev,"CONF_DONE wait timeout\n" ); +return -ETIMEDOUT ; + } + +/* Configure for max. baud rate (3MHz * 4 in bitbang mode) */ +return priv->iops->set_baudrate (priv->intf,3000000 ); +} + +static int fpp_fpga_mgr_ft245_fifo_write (struct fpga_manager *mgr, +const char *buf,size_t count) +{ +return fpp_fpga_mgr_bitbang_write (mgr, buf, count);
drivers/fpga/ftdi-fifo-fpp.c line 324
Quoted 10 lines
drivers/fpga/ftdi-fifo-fpp.c new file +10
-0+} + +static int fpp_fpga_mgr_ft245_fifo_write_complete (struct fpga_manager *mgr, +struct fpga_image_info *info) +{ +struct fpp_fpga_mgr_priv *priv = mgr->priv; +struct device *dev = &priv->pdev->dev; +int retries =MAX_RETRIES ; +int ret; +u8 mask, status;
Can you swap the two lines, reverse xmas-tree please.
Quoted 273 lines
drivers/fpga/ftdi-fifo-fpp.c new file +270
-0+ + mask =IN_CONF_DONE |IN_INIT_DONE ; + +do { + ret =fpp_fpga_mgr_read_status (priv, &status); +if (!ret) { +/* Check conf_done/init_done status */ +if ((status & mask) == mask) +break ; + } + }while (--retries >0 ); + +if (!retries) { +dev_warn (dev,"INIT_DONE wait timeout\n" ); +return -ETIMEDOUT ; + } + +/* Release Reset_n, keep nCONFIG high, too! */ +return fpp_fpga_mgr_set_data_port (priv,OUT_NCONFIG |OUT_RESET_N ,1 ); +} + +static enum fpga_mgr_states fpp_fpga_mgr_state (struct fpga_manager *mgr) +{ +return FPGA_MGR_STATE_UNKNOWN ; +} + +static int fpp_fpga_mgr_write_init (struct fpga_manager *mgr, +struct fpga_image_info *info, +const char *buf,size_t count) +{ +struct fpp_fpga_mgr_priv *priv = mgr->priv; + +if (info && info->flags &FPGA_MGR_PARTIAL_RECONFIG ) { +dev_err (&mgr->dev,"Partial reconfiguration not supported.\n" ); +return -EINVAL ; + } + +if (priv->ops->write_init) +return priv->ops->write_init (mgr, info, buf, count); + +return -ENODEV ; +} + +static int fpp_fpga_mgr_write (struct fpga_manager *mgr,const char *buf, +size_t count) +{ +struct fpp_fpga_mgr_priv *priv = mgr->priv; + +if (priv->ops->write) +return priv->ops->write (mgr, buf, count); + +return -ENODEV ; +} + +static int fpp_fpga_mgr_write_complete (struct fpga_manager *mgr, +struct fpga_image_info *info) +{ +struct fpp_fpga_mgr_priv *priv = mgr->priv; + +if (priv->ops->write_complete) +return priv->ops->write_complete (mgr, info); + +return -ENODEV ; +} + +static struct fpp_mgr_ops fpp_mgr_bitbang_ops = { + .write_init = fpp_fpga_mgr_bitbang_write_init, + .write = fpp_fpga_mgr_bitbang_write, + .write_complete = fpp_fpga_mgr_bitbang_write_complete, +}; + +static struct fpp_mgr_ops fpp_mgr_ft245_fifo_ops = { + .write_init = fpp_fpga_mgr_ft245_fifo_write_init, + .write = fpp_fpga_mgr_ft245_fifo_write, + .write_complete = fpp_fpga_mgr_ft245_fifo_write_complete, +}; + +static const struct fpga_manager_ops fpp_fpga_mgr_ops = { + .state = fpp_fpga_mgr_state, + .write_init = fpp_fpga_mgr_write_init, + .write = fpp_fpga_mgr_write, + .write_complete = fpp_fpga_mgr_write_complete, +}; + +static ssize_t cfg_mode_show (struct device *dev,struct device_attribute *attr, +char *buf) +{ +struct platform_device *pdev =to_platform_device (dev); +struct fpga_manager *mgr =platform_get_drvdata (pdev); +struct fpp_fpga_mgr_priv *priv = mgr->priv; + +return snprintf (buf,PAGE_SIZE ,"%s\n" , priv->cfg_mode); +} + +static ssize_t cfg_mode_store (struct device *dev,struct device_attribute *attr, +const char *buf,size_t count) +{ +struct platform_device *pdev =to_platform_device (dev); +struct fpga_manager *mgr =platform_get_drvdata (pdev); +struct fpp_fpga_mgr_priv *priv = mgr->priv; + +if (!count || count >sizeof (priv->cfg_mode)) +return -EINVAL ; + +if (!strncmp (buf,"fifo" ,4 )) { +strncpy (priv->cfg_mode, buf,sizeof (priv->cfg_mode) -1 ); + priv->cfg_mode[4 ] =0 ; + priv->ops = &fpp_mgr_ft245_fifo_ops; +gpiod_direction_output_raw (priv->conf_done,0 ); + }else if (!strncmp (buf,"bitbang" ,7 )) { +strncpy (priv->cfg_mode, buf,sizeof (priv->cfg_mode) -1 ); + priv->cfg_mode[7 ] =0 ; + priv->ops = &fpp_mgr_bitbang_ops; +gpiod_direction_input (priv->conf_done); + }else { +return -EINVAL ; + } + +return count; +} + +static DEVICE_ATTR_RW (cfg_mode); + +static int fpp_fpga_mgr_probe (struct platform_device *pdev) +{ +struct device *dev = &pdev->dev; +struct fpp_fpga_mgr_priv *priv; +struct fpga_manager *mgr; +struct fifo_fpp_mgr_platform_data *pd; +int ret, retries =MAX_RETRIES ; +char id_string[8 ]; +u8 status =0 ; + + pd = dev->platform_data; +if (!pd) { +dev_err (dev,"Missing platform data.\n" ); +return -EINVAL ; + } + +if (!pd->ops || + !pd->ops->bulk_xfer || !pd->ops->ctrl_xfer || + !pd->ops->read_data || !pd->ops->write_data || + !pd->ops->set_bitmode || !pd->ops->set_baudrate || + !pd->ops->disable_bitbang) +return -EINVAL ; + + priv =devm_kzalloc (dev,sizeof (*priv),GFP_KERNEL ); +if (!priv) +return -ENOMEM ; + + priv->intf =to_usb_interface (dev->parent); + priv->iops = pd->ops; + + ret =sscanf (dev_name (dev->parent),"%s" , priv->usb_dev_id); +if (ret !=1 ) { +dev_err (dev,"Can't get parent device name: %d\n" , ret); +return -ENODEV ; + } + + priv->pdev = pdev; + priv->ops = &fpp_mgr_ft245_fifo_ops; +strncpy (priv->cfg_mode,"fifo" ,sizeof (priv->cfg_mode)); + + priv->nconfig =devm_gpiod_get (dev,"nconfig" ,GPIOD_OUT_LOW ); +if (IS_ERR (priv->nconfig)) { + ret =PTR_ERR (priv->nconfig); +dev_err (dev,"Failed to get nconfig gpio: %d\n" , ret); +return ret; + } + + priv->conf_done =devm_gpiod_get (dev,"conf_done" ,GPIOD_OUT_LOW ); +if (IS_ERR (priv->conf_done)) { + ret =PTR_ERR (priv->conf_done); +dev_err (dev,"Failed to get conf_done gpio: %d\n" , ret); + goto err_cfg1; + } + + priv->bulk_buf =devm_kmalloc (dev,BULK_OUT_BUF_SZ , +GFP_KERNEL |GFP_DMA32 ); +if (!priv->bulk_buf) { + ret = -ENOMEM ; + goto err_cfg2; + } + + ret = priv->iops->set_bitmode (priv->intf,0xff ,BITMODE_SYNCFF ); +if (ret) + goto err_cfg2; + +/* Read status register from CPLD */ +do { + ret =fpp_fpga_mgr_read_status (priv, &status); +if (!ret) +break ; + }while (--retries >0 ); + +if (!retries) { + ret = -ETIMEDOUT ; + goto err_cfg2; + } + + priv->rev = (status &IN_BOARD_REV ) ?BOARD_REVB :BOARD_REVA ; + +if (priv->rev ==BOARD_REVB ) { + priv->addr_sel = (status &IN_ADDR_SELECT ) ? +ADDR_SELECT_NC :ADDR_SELECT_GND ; +if (priv->addr_sel ==ADDR_SELECT_NC ) +strncpy (id_string,"right" ,sizeof (id_string)); +else +strncpy (id_string,"left" ,sizeof (id_string)); + }else { + priv->addr_sel =ADDR_SELECT_INVALID ; +strncpy (id_string,"single" ,sizeof (id_string)); + } + +dev_info (dev,"Board Rev %d, Addr Sel %d\n" , priv->rev, priv->addr_sel); + +/* Use unique board ID and USB bus/port in FPGA manager name */ +snprintf (priv->fpga_mgr_name,sizeof (priv->fpga_mgr_name), +"ftdi-fpp-fpga-mgr %s %s" , id_string, priv->usb_dev_id); + + mgr =devm_fpga_mgr_create (dev, priv->fpga_mgr_name, + &fpp_fpga_mgr_ops, priv); +if (!mgr) + goto err_cfg2; + +platform_set_drvdata (pdev, mgr); + + ret =fpga_mgr_register (mgr); +if (ret) { +dev_err (dev,"unable to register FPGA manager\n" ); + goto err_cfg2; + } + + ret =device_create_file (dev, &dev_attr_cfg_mode); +if (ret) +dev_warn (dev,"Can't create cfg_mode interface %d\n" , ret); + +return 0 ; + +err_cfg2: +devm_gpiod_put (dev, priv->conf_done); +err_cfg1: +devm_gpiod_put (dev, priv->nconfig); +return ret; +} + +static int fpp_fpga_mgr_remove (struct platform_device *pdev) +{ +struct fpga_manager *mgr =platform_get_drvdata (pdev); +struct fpp_fpga_mgr_priv *priv = mgr->priv; + +device_remove_file (&pdev->dev, &dev_attr_cfg_mode); +fpga_mgr_unregister (mgr); +devm_gpiod_put (&pdev->dev, priv->conf_done); +devm_gpiod_put (&pdev->dev, priv->nconfig); +return 0 ; +} + +static struct platform_driver fpp_fpga_mgr_driver = { + .driver.name ="ftdi-fifo-fpp-mgr" , + .probe = fpp_fpga_mgr_probe, + .remove = fpp_fpga_mgr_remove, +}; + +module_platform_driver (fpp_fpga_mgr_driver); + +MODULE_ALIAS ("platform:ftdi-fifo-fpp-mgr" ); +MODULE_AUTHOR ("Anatolij Gustschin <[email protected]>" ); +MODULE_DESCRIPTION ("FT232H Bitbang/FT245-FIFO FPP FPGA Manager Driver" ); +MODULE_LICENSE ("GPL v2" );Signature · 1 line
2.17.1
Thanks,
Moritz
Re: [PATCH v4 3/3] fpga: Add fpga manager driver for ARRI Altera FPP
Hi Moritz,
Quoted 3 lines · On Mon, 8 Apr 2019 11:05:49 -0700 Moritz Fischer [email protected] wrote:
Hi Anatolij,
looks mostly good, a couple of nits inline.
Thanks for review.
...
Quoted 8 lines
drivers/fpga/ftdi-fifo-fpp.c line 5
Quoted 7 lines
+++
b/drivers/fpga/ftdi-fifo-fpp.cdrivers/fpga/ftdi-fifo-fpp.c new file +5
-0@@ -0,0 +1,594 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* Altera FPGA firmware upload via FPP using FT232H Bitbang/FT245-FIFO. +* +* Copyright (C) 2017 - 2018 DENX Software Engineering Maybe bump that to 2019 ;-)
I'll update it in next version.
...
Quoted 5 lines
drivers/fpga/ftdi-fifo-fpp.c line 92
Quoted 3 lines
drivers/fpga/ftdi-fifo-fpp.c new file +3
-0+gpiod_set_raw_value_cansleep (priv->nconfig,1 ); +gpiod_set_raw_value_cansleep (priv->conf_done,0 ); +msleep (50 );You could use a constant here for the 50 ...
Do you mean something like below?
const unsigned int wait_50ms = 50; ... msleep(wait_50ms);
...
Quoted 8 lines
and here ...
Review
Quoted 2 lines
(quoted diff) +2
-0+ gpiod_set_value_cansleep(priv->nconfig, 1); + msleep(50);and here ...
drivers/fpga/ftdi-fifo-fpp.c line 143
Quoted 3 lines
drivers/fpga/ftdi-fifo-fpp.c new file +3
-0+gpiod_set_value_cansleep (priv->nconfig,0 ); + +/* Wait for CONF_DONE to get low */ Does the retry number come from datasheet?
No, it is an empirical value.
...
Quoted 4 lines
Review
Quoted 2 lines
(quoted diff) +2
-0+ if (!retries) { + dev_warn(dev, "CONF_DONE wait timeout\n");warn or err?
err fits better here, I'll update to dev_err().
...
Quoted 7 lines
drivers/fpga/ftdi-fifo-fpp.c line 324
Quoted 5 lines
drivers/fpga/ftdi-fifo-fpp.c new file +5
-0+struct fpp_fpga_mgr_priv *priv = mgr->priv; +struct device *dev = &priv->pdev->dev; +int retries =MAX_RETRIES ; +int ret; +u8 mask, status;Can you swap the two lines, reverse xmas-tree please.
Will do in v5.
Thanks,
Anatolij