Skip to contentSkip to conversation

Add Beelink GS1

PATCH Applied Clément Péron 2 participants 11 messages Apr 8, 2019 – Apr 9, 2019

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

v4 cover Add Beelink GS1

Thanks to Jagan and Icenowy, most of this device-tree is taken from their works on the Orange Pi One Plus and Pine H64.

PLEASE NOTE that I don't own an OrangePi nor a Pine H64 and PIO regulators for these board has not been tested !
Please add a tested-by on these commits 5 and 6 before merging it.

Changes in v4 (Thanks to Maxime Ripard):
- fix incorrect mmc_pins label
- remove default rx/tr timing in emac
- consistency in commit titles

Changes in v3 (Thanks to Maxime Ripard):
- remove PL regulator
- separate patch for sunxi.yaml
- collect reviewed-by

Changes in v2 (Thanks to Maxime Ripard):
- move MMC pinctrl to SOC dtsi
- add board to Sunxi YAML file
- add PIO/R_PIO regulators
- remove always_on from SDIO regulators

Clément Péron (6):
arm64: dts: allwinner: h6: move MMC pinctrl to dtsi
dt-bindings: vendor-prefixes: add AZW
arm64: dts: allwinner: h6: Introduce Beelink GS1 board
dt-bindings: arm: sunxi: Add Beelink GS1 board
arm64: dts: allwinner: h6: orangepi: Add PIO regulators
arm64: dts: allwinner: h6: pine64: Add PIO regulators

 .../devicetree/bindings/arm/sunxi.yaml        |   5 +
 .../devicetree/bindings/vendor-prefixes.txt   |   1 +
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../dts/allwinner/sun50i-h6-beelink-gs1.dts   | 260 ++++++++++++++++++
 .../dts/allwinner/sun50i-h6-orangepi.dtsi     |  19 +-
 .../boot/dts/allwinner/sun50i-h6-pine-h64.dts |  21 +-
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi  |   4 +
 7 files changed, 305 insertions(+), 6 deletions(-)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
Signature · 1 line
2.17.1
#1 lore raw

PATCH v4 1/6 arm64: dts: allwinner: h6: move MMC pinctrl to dtsi

There is only one pinmuxing available for each MMC controller.

Move the pinctrl to the SOC

---
 arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi | 2 --
 arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts  | 4 ----
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi          | 4 ++++
 3 files changed, 4 insertions(+), 6 deletions(-)
arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi +0 -2
index b2526dac2fcf..62e27948a3fa 100644
@@ -56,8 +56,6 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_cldo1>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	bus-width = <4>;
arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts +0 -4
index bdb8470fc8dc..4802902e128f 100644
@@ -104,8 +104,6 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_cldo1>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	bus-width = <4>;
@@ -113,8 +111,6 @@
 };
 
 &mmc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc2_pins>;
 	vmmc-supply = <&reg_cldo1>;
 	vqmmc-supply = <&reg_bldo2>;
 	non-removable;
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +4 -0
index 3e4bb0b0de69..e0dc4a05c1ba 100644
@@ -278,6 +278,8 @@
 			resets = <&ccu RST_BUS_MMC0>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -306,6 +308,8 @@
 			resets = <&ccu RST_BUS_MMC2>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc2_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
Signature · 1 line
2.17.1
#2 lore raw

Re: [PATCH v4 1/6] arm64: dts: allwinner: h6: move MMC pinctrl to dtsi

Quoted 5 lines · Clément Péron

There is only one pinmuxing available for each MMC controller.

Move the pinctrl to the SOC

Applied, thanks

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

Signature · 3 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
For more options, visit https://groups.google.com/d/optout.
#3 lore raw

PATCH v4 2/6 dt-bindings: vendor-prefixes: add AZW

In reply to Clément Péron

Shenzhen AZW Technology Co. Ltd. is a manufacturer specialized in Android smart TV boxes, Intel mini PCs and home cloud TV boxes with NAS.

Add the vendor prefix for AZW.

---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/vendor-prefixes.txt +1 -0
index 208889476a38..4933403c4b57 100644
@@ -54,6 +54,7 @@ avic	Shanghai AVIC Optoelectronics Co., Ltd.
 avnet	Avnet, Inc.
 axentia	Axentia Technologies AB
 axis	Axis Communications AB
+azw     Shenzhen AZW Technology Co., Ltd.
 bananapi BIPAI KEJI LIMITED
 bhf	Beckhoff Automation GmbH & Co. KG
 bitmain	Bitmain Technologies
Signature · 7 lines
2.17.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#4 lore raw

Re: [PATCH v4 2/6] dt-bindings: vendor-prefixes: add AZW

Quoted 7 lines · Clément Péron

Shenzhen AZW Technology Co. Ltd. is a manufacturer specialized in Android smart TV boxes, Intel mini PCs and home cloud TV boxes with NAS.

Add the vendor prefix for AZW.

Applied, thanks!
Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

Signature · 3 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
For more options, visit https://groups.google.com/d/optout.
#5 lore raw

PATCH v4 3/6 arm64: dts: allwinner: h6: Introduce Beelink GS1 board

In reply to Clément Péron

Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supply

---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../dts/allwinner/sun50i-h6-beelink-gs1.dts   | 260 ++++++++++++++++++
 2 files changed, 261 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
arch/arm64/boot/dts/allwinner/Makefile +1 -0
index e4dce2f6fa3a..2dd806a3d5c9 100644
@@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-beelink-gs1.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts new file +260 -0

260 lines not on this page · raw message

Signature · 1 line
2.17.1
#6 lore raw

Re: [PATCH v4 3/6] arm64: dts: allwinner: h6: Introduce Beelink GS1 board

Quoted 14 lines · Clément Péron

Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supply

Quoted 1 line

Applied, thanks

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

Signature · 3 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
For more options, visit https://groups.google.com/d/optout.
#7 lore raw

PATCH v4 4/6 dt-bindings: arm: sunxi: Add Beelink GS1 board

In reply to Clément Péron

Beelink GS1 device-tree has been introduced.

Add it to the sunxi yaml documentation.

---
 Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
 1 file changed, 5 insertions(+)
Documentation/devicetree/bindings/arm/sunxi.yaml +5 -0
index 11563d3f7c65..9ab9b266881d 100644
@@ -136,6 +136,11 @@ properties:
           - const: lemaker,bananapro
           - const: allwinner,sun7i-a20
 
+      - description: Beelink GS1
+        items:
+          - const: azw,beelink-gs1
+          - const: allwinner,sun50i-h6
+
       - description: Beelink X2
         items:
           - const: roofull,beelink-x2
Signature · 1 line
2.17.1
#8 lore raw

Re: [PATCH v4 4/6] dt-bindings: arm: sunxi: Add Beelink GS1 board

Quoted 5 lines · Clément Péron

Beelink GS1 device-tree has been introduced.

Add it to the sunxi yaml documentation.

Applied, thanks!
Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

Signature · 3 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
For more options, visit https://groups.google.com/d/optout.
#9 lore raw

PATCH v4 5/6 arm64: dts: allwinner: h6: orangepi: Add PIO regulators

In reply to Clément Péron

OrangePi One Plus and OrangePi Lite2 use the same PIO regulators.

Add this in the common device tree.

---
 .../boot/dts/allwinner/sun50i-h6-orangepi.dtsi  | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi +17 -0
index 62e27948a3fa..4044f2dc66ac 100644
@@ -70,6 +70,12 @@
 	status = "okay";
 };
 
+&pio {
+	vcc-pc-supply = <&reg_bldo2>;
+	vcc-pd-supply = <&reg_cldo1>;
+	vcc-pg-supply = <&reg_bldo3>;
+};
+
 &r_i2c {
 	status = "okay";
 
@@ -189,6 +195,17 @@
 	};
 };
 
+&r_pio {
+	/*
+	 * PL0 and PL1 are used for PMIC I2C
+	 * don't enable the pl-supply else
+	 * it will fail at boot
+	 *
+	 * vcc-pl-supply = <&reg_aldo1>;
+	 */
+	vcc-pm-supply = <&reg_bldo3>;
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_ph_pins>;
Signature · 1 line
2.17.1
#10 lore raw

PATCH v4 6/6 arm64: dts: allwinner: h6: pine64: Add PIO regulators

In reply to Clément Péron

Add PIO regulators for Pine64 board.

---
 .../boot/dts/allwinner/sun50i-h6-pine-h64.dts   | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts +17 -0
index 4802902e128f..6f2d9adf4f10 100644
@@ -127,6 +127,12 @@
 	status = "okay";
 };
 
+&pio {
+	vcc-pc-supply = <&reg_bldo2>;
+	vcc-pd-supply = <&reg_cldo1>;
+	vcc-pg-supply = <&reg_bldo2>;
+};
+
 &r_i2c {
 	status = "okay";
 
@@ -247,6 +253,17 @@
 	};
 };
 
+&r_pio {
+	/*
+	 * PL0 and PL1 are used for PMIC I2C
+	 * don't enable the pl-supply else
+	 * it will fail at boot
+	 *
+	 * vcc-pl-supply = <&reg_aldo1>;
+	 */
+	vcc-pm-supply = <&reg_bldo2>;
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_ph_pins>;
Signature · 1 line
2.17.1