arm: socfpga: clean up socfpga_common.h
v2 cover arm: socfpga: clean up socfpga_common.h
This series cleans up the include/configs/socfpga_common.h file a bit.
It removes some defines that are used nowhere and cleans up some leftovers after various subsystems have been converted to use DM.
Changes in v2:
- added patch to move socfpga_vining to DM_I2C
- remove even more outdated things
- added patch with further cleanups to the socfpga board config files
Simon Goldschmidt (4):
arm: socfpga: move vining_fpga to DM_I2C
arm: socfpga: clean up socfpga_common.h
arm: socfpga: remove CONFIG_SYS_BOOTMAPSZ
arm: socfpga: clean up board config files
configs/socfpga_vining_fpga_defconfig | 8 ++- include/configs/socfpga_arria10_socdk.h | 6 --- include/configs/socfpga_arria5_socdk.h | 2 - include/configs/socfpga_common.h | 68 ------------------------ include/configs/socfpga_cyclone5_socdk.h | 2 - include/configs/socfpga_de0_nano_soc.h | 2 - include/configs/socfpga_de10_nano.h | 2 - include/configs/socfpga_de1_soc.h | 2 - include/configs/socfpga_is1.h | 2 - include/configs/socfpga_sockit.h | 2 - include/configs/socfpga_socrates.h | 2 - include/configs/socfpga_sr1500.h | 11 ---- include/configs/socfpga_vining_fpga.h | 18 ------- 13 files changed, 7 insertions(+), 120 deletions(-)
Signature · 1 line
2.17.1
PATCH v2 1/4 arm: socfpga: move vining_fpga to DM_I2C
All socfpga boards except for vining_fpga use DM_I2C. Enable DM_I2C for this board and set the EEPROM defines via Kconfig (enabling CONFIG_I2C_EEPROM from MISC).
---
Changes in v2:
- added (this) patch to move socfpga_vining to DM_I2C
configs/socfpga_vining_fpga_defconfig | 8 +++++++- include/configs/socfpga_common.h | 26 -------------------------- include/configs/socfpga_vining_fpga.h | 9 --------- 3 files changed, 7 insertions(+), 36 deletions(-)
configs/socfpga_vining_fpga_defconfig +7 -1
@@ -16,8 +16,8 @@ CONFIG_VERSION_VARIABLE=y CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_SPI_LOAD=y CONFIG_CMD_ASKENV=y -CONFIG_CMD_GREPENV=y CONFIG_CMD_EEPROM=y +CONFIG_CMD_GREPENV=y CONFIG_CMD_DFU=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_GPIO=y
@@ -44,6 +44,7 @@ CONFIG_DFU_RAM=y CONFIG_DFU_SF=y CONFIG_DM_GPIO=y CONFIG_DWAPB_GPIO=y +CONFIG_DM_I2C=y CONFIG_LED_STATUS=y CONFIG_LED_STATUS_GPIO=y CONFIG_LED_STATUS0=y
@@ -55,6 +56,11 @@ CONFIG_LED_STATUS_BIT2=54 CONFIG_LED_STATUS3=y CONFIG_LED_STATUS_BIT3=65 CONFIG_LED_STATUS_CMD=y +CONFIG_MISC=y +CONFIG_I2C_EEPROM=y +CONFIG_SYS_I2C_EEPROM_ADDR=0x50 +CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=3 +CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=70 CONFIG_DM_MMC=y CONFIG_MMC_DW=y CONFIG_MTD_DEVICE=y
include/configs/socfpga_common.h +0 -26
@@ -149,32 +149,6 @@#define CONFIG_SYS_NAND_DATA_BASE SOCFPGA_NANDDATA_ADDRESS#endif -/* -* I2C support -*/ -#ifndef CONFIG_DM_I2C -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_BASE SOCFPGA_I2C0_ADDRESS -#define CONFIG_SYS_I2C_BASE1 SOCFPGA_I2C1_ADDRESS -#define CONFIG_SYS_I2C_BASE2 SOCFPGA_I2C2_ADDRESS -#define CONFIG_SYS_I2C_BASE3 SOCFPGA_I2C3_ADDRESS -/* Using standard mode which the speed up to 100Kb/s */ -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SPEED1 100000 -#define CONFIG_SYS_I2C_SPEED2 100000 -#define CONFIG_SYS_I2C_SPEED3 100000 -/* Address of device when used as slave */ -#define CONFIG_SYS_I2C_SLAVE 0x02 -#define CONFIG_SYS_I2C_SLAVE1 0x02 -#define CONFIG_SYS_I2C_SLAVE2 0x02 -#define CONFIG_SYS_I2C_SLAVE3 0x02 -#ifndef __ASSEMBLY__ -/* Clock supplied to I2C controller in unit of MHz */ -unsigned int cm_get_l4_sp_clk_hz (void ); -#define IC_CLK (cm_get_l4_sp_clk_hz() / 1000000) -#endif -#endif /* CONFIG_DM_I2C */ -/* * QSPI support */
include/configs/socfpga_vining_fpga.h +0 -9
@@ -16,15 +16,6 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* I2C EEPROM */ -#ifdef CONFIG_CMD_EEPROM -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_I2C_EEPROM_BUS 0 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 -#endif -/* * Status LEDs: * 0 ... Top Green
Signature · 1 line
2.17.1
PATCH v2 1/4 arm: socfpga: move vining_fpga to DM_I2C
Quoted 7 lines · Simon Goldschmidt
All socfpga boards except for
vining_fpgauseDM_I2C. EnableDM_I2Cfor this board and set the EEPROM defines viaKconfig(enablingCONFIG_I2C_EEPROMfrom MISC).Signed-off-by Simon Goldschmidt <[email protected]>---
Quoted 7 lines
Changes in v2:
- added (this) patch to movesocfpga_viningtoDM_I2Cconfigs/socfpga_vining_fpga_defconfig | 8 +++++++- include/configs/socfpga_common.h | 26 -------------------------- include/configs/socfpga_vining_fpga.h | 9 --------- 3 files changed, 7 insertions(+), 36 deletions(-)
Isn't this missing some DT bit which would enable the I2C controller ? Or is that already in the DT for this platform ?
Signature · 2 lines
Best regards, Marek Vasut
PATCH v2 1/4 arm: socfpga: move vining_fpga to DM_I2C
Am 09.04.2019 um 21:27 schrieb Marek Vasut:
Quoted 11 lines · Simon Goldschmidt
Quoted 10 lines
All socfpga boards except for
vining_fpgauseDM_I2C. EnableDM_I2Cfor this board and set the EEPROM defines viaKconfig(enablingCONFIG_I2C_EEPROMfrom MISC).Signed-off-by Simon Goldschmidt <[email protected]>---
Changes in v2:
- added (this) patch to movesocfpga_viningtoDM_I2C
Quoted 8 lines
Quoted 4 lines
configs/socfpga_vining_fpga_defconfig | 8 +++++++- include/configs/socfpga_common.h | 26 -------------------------- include/configs/socfpga_vining_fpga.h | 9 --------- 3 files changed, 7 insertions(+), 36 deletions(-)Isn't this missing some DT bit which would enable the I2C controller ? Or is that already in the DT for this platform ?
Well, I don't have the board (I tested with socfpga_socrates + Phy1 addon board which does have an i2c eeprom but needs an FPGA config to work), but to me it seems 'socfpga_cyclone5_vining_fpga.dts' should have everything we need, or what do you think is missing?
Having this tested on a real socfpga_vining board would be great of course...
Regards,
Simon
PATCH v2 1/4 arm: socfpga: move vining_fpga to DM_I2C
Quoted 17 lines · Simon Goldschmidt
Am 09.04.2019 um 21:27 schrieb Marek Vasut:
Quoted 16 lines · Simon Goldschmidt
Quoted 14 lines
All socfpga boards except for
vining_fpgauseDM_I2C. EnableDM_I2Cfor this board and set the EEPROM defines viaKconfig(enablingCONFIG_I2C_EEPROMfrom MISC).Signed-off-by Simon Goldschmidt <[email protected]>---
Changes in v2:
- added (this) patch to movesocfpga_viningtoDM_I2Cconfigs/socfpga_vining_fpga_defconfig | 8 +++++++- include/configs/socfpga_common.h | 26 --------------------------
include/configs/socfpga_vining_fpga.h| 9 ---------3 files changed, 7 insertions(+), 36 deletions(-)
Quoted 8 lines
Quoted 3 lines
Isn't this missing some DT bit which would enable the I2C controller ? Or is that already in the DT for this platform ?
Well, I don't have the board (I tested with
socfpga_socrates+ Phy1 addon board which does have an i2c eeprom but needs an FPGA config to work), but to me it seems 'socfpga_cyclone5_vining_fpga.dts' should have everything we need, or what do you think is missing?
I was just curious whether you checked that.
Quoted 2 lines
Having this tested on a real
socfpga_viningboard would be great of course...
I'll arrange for that.
Signature · 2 lines
Best regards, Marek Vasut
PATCH v2 2/4 arm: socfpga: clean up socfpga_common.h
In reply to Simon GoldschmidtRemove outdated defines (not used any more, outdated due to DM conversion) from socfpga_common.h.
---
Changes in v2:
- remove even more outdated things
include/configs/socfpga_common.h | 40 -------------------------------- 1 file changed, 40 deletions(-)
include/configs/socfpga_common.h +0 -40
@@ -72,29 +72,12 @@#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot argument buffer size */ -#ifndef CONFIG_SYS_HOSTNAME -#define CONFIG_SYS_HOSTNAME CONFIG_SYS_BOARD -#endif -/* * Cache */ #define CONFIG_SYS_L2_PL310 #define CONFIG_SYS_PL310_BASE SOCFPGA_MPUL2_ADDRESS -/* -* EPCS/EPCQx1 Serial Flash Controller -*/ -#ifdef CONFIG_ALTERA_SPI -/* -* The base address is configurable in QSys, each board must specify the -* base address based on it's particular FPGA configuration. Please note -* that the address here is incremented by 0x400 from the Base address -* selected in QSys, since the SPI registers are at offset +0x400. -* #define CONFIG_SYS_SPI_BASE 0xff240400 -*/ -#endif -/* * Ethernet on SoC (EMAC) */
@@ -162,15 +145,6 @@ unsigned int cm_get_qspi_controller_clk_hz(void);#define CONFIG_CQSPI_REF_CLK cm_get_qspi_controller_clk_hz()#endif -/* -* Designware SPI support -*/ - -/* -* Serial Driver -*/ -#define CONFIG_SYS_NS16550_SERIAL -/* * USB */
@@ -206,20 +180,6 @@ unsigned int cm_get_qspi_controller_clk_hz(void);#define CONFIG_ENV_SECT_SIZE (64 * 1024)#endif -/* -* mtd partitioning for serial NOR flash -* -* device nor0 <ff705000.spi.0>, # parts = 6 -* #: name size offset mask_flags -* 0: u-boot 0x00100000 0x00000000 0 -* 1: env1 0x00040000 0x00100000 0 -* 2: env2 0x00040000 0x00140000 0 -* 3: UBI 0x03e80000 0x00180000 0 -* 4: boot 0x00e80000 0x00180000 0 -* 5: rootfs 0x01000000 0x01000000 0 -* -*/ -/* * SPL *
Signature · 1 line
2.17.1
PATCH v2 2/4 arm: socfpga: clean up socfpga_common.h
Quoted 2 lines · Simon Goldschmidt
Remove outdated defines (not used any more, outdated due to DM conversion) from
socfpga_common.h.
s/defines/macros and comments/
Quoted 45 lines
Signed-off-by Simon Goldschmidt <[email protected]>---
Changes in v2:
- remove even more outdated thingsinclude/configs/socfpga_common.h | 40 -------------------------------- 1 file changed, 40 deletions(-)include/configs/socfpga_common.h +0
-17@@ -72,29 +72,12 @@#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot argument buffer size */ -#ifndef CONFIG_SYS_HOSTNAME -#define CONFIG_SYS_HOSTNAME CONFIG_SYS_BOARD -#endif -/* * Cache */ #define CONFIG_SYS_L2_PL310 #define CONFIG_SYS_PL310_BASE SOCFPGA_MPUL2_ADDRESS -/* -* EPCS/EPCQx1 Serial Flash Controller -*/ -#ifdef CONFIG_ALTERA_SPI -/* -* The base address is configurable in QSys, each board must specify the -* base address based on it's particular FPGA configuration. Please note -* that the address here is incremented by 0x400 from the Base address -* selected in QSys, since the SPI registers are at offset +0x400. -* #define CONFIG_SYS_SPI_BASE 0xff240400 -*/ -#endif -/* * Ethernet on SoC (EMAC) */ @@ -162,15 +145,6 @@ unsigned int cm_get_qspi_controller_clk_hz(void);#define CONFIG_CQSPI_REF_CLK cm_get_qspi_controller_clk_hz()
include/configs/socfpga_common.h unsigned int cm_get_qspi_controller_clk_hz(void); · line 172
Quoted 10 lines
include/configs/socfpga_common.h +0
-8#endif -/* -* Designware SPI support -*/ - -/* -* Serial Driver -*/ -#define CONFIG_SYS_NS16550_SERIAL
Are you sure about this one ?
Quoted 25 lines
include/configs/socfpga_common.h +0
-14/* * USB */ @@ -206,20 +180,6 @@ unsigned int cm_get_qspi_controller_clk_hz(void);#define CONFIG_ENV_SECT_SIZE (64 * 1024)#endif -/* -* mtd partitioning for serial NOR flash -* -* device nor0 <ff705000.spi.0>, # parts = 6 -* #: name size offset mask_flags -* 0: u-boot 0x00100000 0x00000000 0 -* 1: env1 0x00040000 0x00100000 0 -* 2: env2 0x00040000 0x00140000 0 -* 3: UBI 0x03e80000 0x00180000 0 -* 4: boot 0x00e80000 0x00180000 0 -* 5: rootfs 0x01000000 0x01000000 0 -* -*/ -/* * SPL *
Signature · 2 lines
Best regards, Marek Vasut
PATCH v2 2/4 arm: socfpga: clean up socfpga_common.h
Am 09.04.2019 um 21:28 schrieb Marek Vasut:
Quoted 52 lines · Simon Goldschmidt
Quoted 2 lines
Remove outdated defines (not used any more, outdated due to DM conversion) from
socfpga_common.h.s/defines/macros and comments/ >
Quoted 47 lines
Signed-off-by Simon Goldschmidt <[email protected]>---
Changes in v2:
- remove even more outdated thingsinclude/configs/socfpga_common.h | 40 -------------------------------- 1 file changed, 40 deletions(-)include/configs/socfpga_common.h +0
-17@@ -72,29 +72,12 @@#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot argument buffer size */ -#ifndef CONFIG_SYS_HOSTNAME -#define CONFIG_SYS_HOSTNAME CONFIG_SYS_BOARD -#endif -/* * Cache */ #define CONFIG_SYS_L2_PL310 #define CONFIG_SYS_PL310_BASE SOCFPGA_MPUL2_ADDRESS -/* -* EPCS/EPCQx1 Serial Flash Controller -*/ -#ifdef CONFIG_ALTERA_SPI -/* -* The base address is configurable in QSys, each board must specify the -* base address based on it's particular FPGA configuration. Please note -* that the address here is incremented by 0x400 from the Base address -* selected in QSys, since the SPI registers are at offset +0x400. -* #define CONFIG_SYS_SPI_BASE 0xff240400 -*/ -#endif -/* * Ethernet on SoC (EMAC) */ @@ -162,15 +145,6 @@ unsigned int cm_get_qspi_controller_clk_hz(void);#define CONFIG_CQSPI_REF_CLK cm_get_qspi_controller_clk_hz()#endif
Quoted 10 lines
include/configs/socfpga_common.h unsigned int cm_get_qspi_controller_clk_hz(void); · line 172
Quoted 8 lines
include/configs/socfpga_common.h +0
-8-/* -* Designware SPI support -*/ - -/* -* Serial Driver -*/ -#define CONFIG_SYS_NS16550_SERIAL Are you sure about this one ?
Yes. This is only used in 'drivers/serial/Makefile' if CONFIG_DM_SERIAL is not defined. No need to keep it.
Should I still send a v3 for the commit message?
Regards,
Simon
Quoted 28 lines
Quoted 26 lines
include/configs/socfpga_common.h +0
-14/* * USB */ @@ -206,20 +180,6 @@ unsigned int cm_get_qspi_controller_clk_hz(void);#define CONFIG_ENV_SECT_SIZE (64 * 1024)#endif -/* -* mtd partitioning for serial NOR flash -* -* device nor0 <ff705000.spi.0>, # parts = 6 -* #: name size offset mask_flags -* 0: u-boot 0x00100000 0x00000000 0 -* 1: env1 0x00040000 0x00100000 0 -* 2: env2 0x00040000 0x00140000 0 -* 3: UBI 0x03e80000 0x00180000 0 -* 4: boot 0x00e80000 0x00180000 0 -* 5: rootfs 0x01000000 0x01000000 0 -* -*/ -/* * SPL *
PATCH v2 2/4 arm: socfpga: clean up socfpga_common.h
Quoted 65 lines · Simon Goldschmidt
Am 09.04.2019 um 21:28 schrieb Marek Vasut:
Quoted 55 lines · Simon Goldschmidt
Quoted 2 lines
Remove outdated defines (not used any more, outdated due to DM conversion) from
socfpga_common.h.s/defines/macros and comments/ >
Quoted 50 lines
Signed-off-by Simon Goldschmidt <[email protected]>---
Changes in v2:
- remove even more outdated things
include/configs/socfpga_common.h| 40 --------------------------------1 file changed, 40 deletions(-)include/configs/socfpga_common.h +0
-0@@ -72,29 +72,12 @@ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot argument buffer size */-#ifndef
CONFIG_SYS_HOSTNAMEinclude/configs/socfpga_common.h +0
-3-#define CONFIG_SYS_HOSTNAME CONFIG_SYS_BOARD -#endif -/*
* Cache
*/
#defineCONFIG_SYS_L2_PL310
#define CONFIG_SYS_PL310_BASESOCFPGA_MPUL2_ADDRESS-/*
- * EPCS/EPCQx1 Serial Flash Controller
- */include/configs/socfpga_common.h +0
-3-#ifdef CONFIG_ALTERA_SPI -/* -* The base address is configurable in QSys, each board must specify the
- * base address based on it's particular FPGA configuration. Please note
- * that the address here is incremented by 0x400 from the Base address
- * selected in QSys, since the SPI registers are at offset +0x400.
- * #define CONFIG_SYS_SPI_BASE0xff240400
- */include/configs/socfpga_common.h +0
-2-#endif -/*
* Ethernet on SoC (EMAC)
*/include/configs/socfpga_common.h +0
-0@@ -162,15 +145,6 @@ unsigned int cm_get_qspi_controller_clk_hz(void); #define CONFIG_CQSPI_REF_CLK cm_get_qspi_controller_clk_hz() #endif-/*
- * Designware SPI supportQuoted 8 lines
include/configs/socfpga_common.h unsigned int cm_get_qspi_controller_clk_hz(void); · line 172
Quoted 6 lines
- */
include/configs/socfpga_common.h +0
-5- -/* -* Serial Driver -*/ -#define CONFIG_SYS_NS16550_SERIAL Are you sure about this one ?
Quoted 4 lines
Yes. This is only used in '
drivers/serial/Makefile' ifCONFIG_DM_SERIALis not defined. No need to keep it.Should I still send a v3 for the commit message?
Would be nice. Can you prep me a PR with the patches for current release?
Signature · 2 lines
Best regards, Marek Vasut
PATCH v2 3/4 arm: socfpga: remove CONFIG_SYS_BOOTMAPSZ
In reply to Simon Goldschmidtsocfpga_common.h defines CONFIG_SYS_BOOTMAPSZ to 64 MiB.
Since having this define overrides the 'bootm_size' env variable for the whole socfpga platform, let's remove this define from socfpga_common.h and instead rely on the 'bootm_size' env variable (which is initialized to 160 MiB in the same file's default env). This gives users the chance to override it in their own environment.
---
Changes in v2: None
include/configs/socfpga_common.h | 2 -- 1 file changed, 2 deletions(-)
include/configs/socfpga_common.h +0 -2
@@ -10,8 +10,6 @@*/ #define CONFIG_CLOCKS -#define CONFIG_SYS_BOOTMAPSZ (64 * 1024 * 1024) -#define CONFIG_TIMESTAMP /* Print image info with timestamp */ /*
Signature · 1 line
2.17.1
PATCH v2 3/4 arm: socfpga: remove CONFIG_SYS_BOOTMAPSZ
Quoted 22 lines · Simon Goldschmidt
socfpga_common.hdefinesCONFIG_SYS_BOOTMAPSZto 64 MiB.Since having this define overrides the '
bootm_size' env variable for the whole socfpga platform, let's remove this define fromsocfpga_common.hand instead rely on the 'bootm_size' env variable (which is initialized to 160 MiB in the same file's default env). This gives users the chance to override it in their own environment.Signed-off-by Simon Goldschmidt <[email protected]>---
Changes in v2: None
include/configs/socfpga_common.h | 2 -- 1 file changed, 2 deletions(-)include/configs/socfpga_common.h +0
-0
include/configs/socfpga_common.h line 15
Quoted 8 lines
include/configs/socfpga_common.h +0
-2@@ -10,8 +10,6 @@*/ #define CONFIG_CLOCKS -#define CONFIG_SYS_BOOTMAPSZ (64 * 1024 * 1024) -#define CONFIG_TIMESTAMP /* Print image info with timestamp */ /*
Signature · 2 lines
Best regards, Marek Vasut
PATCH v2 4/4 arm: socfpga: clean up board config files
In reply to Simon GoldschmidtRemove outdated defines (not used any more, outdated due to DM conversion) from various socfpga files in include/config.
---
Changes in v2:
- added (this) patch with further cleanups to the socfpga board config files
include/configs/socfpga_arria10_socdk.h | 6 ------ include/configs/socfpga_arria5_socdk.h | 2 -- include/configs/socfpga_cyclone5_socdk.h | 2 -- include/configs/socfpga_de0_nano_soc.h | 2 -- include/configs/socfpga_de10_nano.h | 2 -- include/configs/socfpga_de1_soc.h | 2 -- include/configs/socfpga_is1.h | 2 -- include/configs/socfpga_sockit.h | 2 -- include/configs/socfpga_socrates.h | 2 -- include/configs/socfpga_sr1500.h | 11 ----------- include/configs/socfpga_vining_fpga.h | 9 --------- 11 files changed, 42 deletions(-)
include/configs/socfpga_arria10_socdk.h +0 -6
@@ -19,12 +19,6 @@/* Memory configurations */ #define PHYS_SDRAM_1_SIZE 0x40000000 -/* Ethernet on SoC (EMAC) */ - -/* -* U-Boot environment configurations -*/ -/* * Serial / UART configurations */
include/configs/socfpga_arria5_socdk.h +0 -2
@@ -14,8 +14,6 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* Ethernet on SoC (EMAC) */ -/* The rest of the configuration is shared */ #include <configs/socfpga_common.h>
include/configs/socfpga_cyclone5_socdk.h +0 -2
@@ -14,8 +14,6 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* Ethernet on SoC (EMAC) */ -/* The rest of the configuration is shared */ #include <configs/socfpga_common.h>
include/configs/socfpga_de0_nano_soc.h +0 -2
@@ -14,8 +14,6 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* Ethernet on SoC (EMAC) */ -/* The rest of the configuration is shared */ #include <configs/socfpga_common.h>
include/configs/socfpga_de10_nano.h +0 -2
@@ -14,8 +14,6 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* Ethernet on SoC (EMAC) */ -/* The rest of the configuration is shared */ #include <configs/socfpga_common.h>
include/configs/socfpga_de1_soc.h +0 -2
@@ -14,8 +14,6 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* Ethernet on SoC (EMAC) */ -/* The rest of the configuration is shared */ #include <configs/socfpga_common.h>
include/configs/socfpga_is1.h +0 -2
@@ -19,8 +19,6 @@/* Ethernet on SoC (EMAC) */ #if defined(CONFIG_CMD_NET )#define CONFIG_ARP_TIMEOUT 500UL - -/* PHY */ #endif /* The rest of the configuration is shared */
include/configs/socfpga_sockit.h +0 -2
@@ -14,8 +14,6 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* Ethernet on SoC (EMAC) */ -/* The rest of the configuration is shared */ #include <configs/socfpga_common.h>
include/configs/socfpga_socrates.h +0 -2
@@ -14,8 +14,6 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* Ethernet on SoC (EMAC) */ -/* The rest of the configuration is shared */ #include <configs/socfpga_common.h>
include/configs/socfpga_sr1500.h +0 -11
@@ -19,8 +19,6 @@/* The PHY is autodetected, so no MII PHY address is needed here */ #define PHY_ANEG_TIMEOUT 8000 -/* Environment */ -/* Enable SPI NOR flash reset, needed for SPI booting */ #define CONFIG_SPI_N25Q256A_RESET
@@ -36,15 +34,6 @@#define CONFIG_ENV_OFFSET 0x000e0000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE) -/* -* The QSPI NOR flash layout on SR1500: -* -* 0000.0000 - 0003.ffff: SPL (4 times) -* 0004.0000 - 000d.ffff: U-Boot -* 000e.0000 - 000e.ffff: env1 -* 000f.0000 - 000f.ffff: env2 -*/ -/* The rest of the configuration is shared */ #include <configs/socfpga_common.h>
include/configs/socfpga_vining_fpga.h +0 -9
@@ -16,18 +16,9 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* -* Status LEDs: -* 0 ... Top Green -* 1 ... Top Red -* 2 ... Bottom Green -* 3 ... Bottom Red -*/ -/* Ethernet on SoC (EMAC) */ #if defined(CONFIG_CMD_NET )#define CONFIG_BOOTP_SEND_HOSTNAME -/* PHY */ #endif /* Extra Environment */
Signature · 1 line
2.17.1
PATCH v2 4/4 arm: socfpga: clean up board config files
Quoted 187 lines · Simon Goldschmidt
Remove outdated defines (not used any more, outdated due to DM conversion) from various socfpga files in
include/config.Signed-off-by Simon Goldschmidt <[email protected]>---
Changes in v2:
- added (this) patch with further cleanups to the socfpga board config filesinclude/configs/socfpga_arria10_socdk.h | 6 ------ include/configs/socfpga_arria5_socdk.h | 2 -- include/configs/socfpga_cyclone5_socdk.h | 2 -- include/configs/socfpga_de0_nano_soc.h | 2 -- include/configs/socfpga_de10_nano.h | 2 -- include/configs/socfpga_de1_soc.h | 2 -- include/configs/socfpga_is1.h | 2 -- include/configs/socfpga_sockit.h | 2 -- include/configs/socfpga_socrates.h | 2 -- include/configs/socfpga_sr1500.h | 11 ----------- include/configs/socfpga_vining_fpga.h | 9 --------- 11 files changed, 42 deletions(-)include/configs/socfpga_arria10_socdk.h +0
-6@@ -19,12 +19,6 @@/* Memory configurations */ #define PHYS_SDRAM_1_SIZE 0x40000000 -/* Ethernet on SoC (EMAC) */ - -/* -* U-Boot environment configurations -*/ -/* * Serial / UART configurations */ include/configs/socfpga_arria5_socdk.h +0
-2@@ -14,8 +14,6 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* Ethernet on SoC (EMAC) */ -/* The rest of the configuration is shared */ #include <configs/socfpga_common.h> include/configs/socfpga_cyclone5_socdk.h +0
-2@@ -14,8 +14,6 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* Ethernet on SoC (EMAC) */ -/* The rest of the configuration is shared */ #include <configs/socfpga_common.h> include/configs/socfpga_de0_nano_soc.h +0
-2@@ -14,8 +14,6 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* Ethernet on SoC (EMAC) */ -/* The rest of the configuration is shared */ #include <configs/socfpga_common.h> include/configs/socfpga_de10_nano.h +0
-2@@ -14,8 +14,6 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* Ethernet on SoC (EMAC) */ -/* The rest of the configuration is shared */ #include <configs/socfpga_common.h> include/configs/socfpga_de1_soc.h +0
-2@@ -14,8 +14,6 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* Ethernet on SoC (EMAC) */ -/* The rest of the configuration is shared */ #include <configs/socfpga_common.h> include/configs/socfpga_is1.h +0
-2@@ -19,8 +19,6 @@/* Ethernet on SoC (EMAC) */ #if defined(CONFIG_CMD_NET )#define CONFIG_ARP_TIMEOUT 500UL - -/* PHY */ #endif /* The rest of the configuration is shared */ include/configs/socfpga_sockit.h +0
-2@@ -14,8 +14,6 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* Ethernet on SoC (EMAC) */ -/* The rest of the configuration is shared */ #include <configs/socfpga_common.h> include/configs/socfpga_socrates.h +0
-2@@ -14,8 +14,6 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* Ethernet on SoC (EMAC) */ -/* The rest of the configuration is shared */ #include <configs/socfpga_common.h> include/configs/socfpga_sr1500.h +0
-11@@ -19,8 +19,6 @@/* The PHY is autodetected, so no MII PHY address is needed here */ #define PHY_ANEG_TIMEOUT 8000 -/* Environment */ -/* Enable SPI NOR flash reset, needed for SPI booting */ #define CONFIG_SPI_N25Q256A_RESET @@ -36,15 +34,6 @@#define CONFIG_ENV_OFFSET 0x000e0000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE) -/* -* The QSPI NOR flash layout on SR1500: -* -* 0000.0000 - 0003.ffff: SPL (4 times) -* 0004.0000 - 000d.ffff: U-Boot -* 000e.0000 - 000e.ffff: env1 -* 000f.0000 - 000f.ffff: env2 -*/ -/* The rest of the configuration is shared */ #include <configs/socfpga_common.h> include/configs/socfpga_vining_fpga.h +0
-5@@ -16,18 +16,9 @@#define CONFIG_LOADADDR 0x01000000#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* -* Status LEDs: -* 0 ... Top Green -* 1 ... Top Red -* 2 ... Bottom Green
include/configs/socfpga_vining_fpga.h line 24
Quoted 10 lines
include/configs/socfpga_vining_fpga.h +0
-4-* 3 ... Bottom Red -*/ -/* Ethernet on SoC (EMAC) */ #if defined(CONFIG_CMD_NET )#define CONFIG_BOOTP_SEND_HOSTNAME -/* PHY */ #endif /* Extra Environment */
Signature · 2 lines
Best regards, Marek Vasut