Pinctrl driver updates for RZ/G2E
cover Pinctrl driver updates for RZ/G2E
Dear All,
this series backports the latest commits for the pinctrl driver for the RZ/G2E (a.k.a. r8a774c0).
This series depends on:
https://patchwork.kernel.org/project/cip-dev/list/?series=95351
Thanks,
Fab
Geert Uytterhoeven (3):
pinctrl: sh-pfc: r8a77990: Fix IOCTRL reg state after s2ram on R-Car
E3
pinctrl: sh-pfc: r8a77990: Fix MOD_SEL0 SEL_I2C1 field width
pinctrl: sh-pfc: r8a77990: GP6_9 does not have pull-down capability
Takeshi Kihara (7):
pinctrl: sh-pfc: r8a77990: Add CAN pins, groups and functions
pinctrl: sh-pfc: r8a77990: Add CAN FD pins, groups and functions
pinctrl: sh-pfc: r8a77990: Fix MOD_SEL0 bit3 when using TX0
pinctrl: sh-pfc: r8a77990: Fix MOD_SEL0 bit2 when using RX2, TX2 and
SCK2
pinctrl: sh-pfc: r8a77990: Fix MOD_SEL bit numbering
pinctrl: sh-pfc: r8a77990: Add TMU pins, groups and functions
pinctrl: sh-pfc: r8a77990: Add DRIF pins, groups and functions
drivers/pinctrl/sh-pfc/pfc-r8a77990.c | 448 ++++++++++++++++++++++++++++++++-- 1 file changed, 422 insertions(+), 26 deletions(-)
Signature · 1 line
2.7.4
PATCH 1/10 pinctrl: sh-pfc: r8a77990: Add CAN pins, groups and functions
From: Takeshi Kihara <[email protected]>
commit c1e5bd286fe501992165608551f889ec69f5901a upstream.
This patch adds CAN{0,1} pins, groups and functions to the R8A77990 SoC.
--- drivers/pinctrl/sh-pfc/pfc-r8a77990.c | 51 +++++++++++++++++++++++++++++++++-- 1 file changed, 49 insertions(+), 2 deletions(-)
drivers/pinctrl/sh-pfc/pfc-r8a77990.c +49 -2
@@ -1538,6 +1538,35 @@ static const unsigned int avb_avtp_capture_a_mux[] = { AVB_AVTP_CAPTURE_A_MARK, }; +/* - CAN ------------------------------------------------------------------ */ +static const unsigned int can0_data_pins[] = { +/* TX, RX */ +RCAR_GP_PIN (0 ,12 ),RCAR_GP_PIN (0 ,13 ), +}; + +static const unsigned int can0_data_mux[] = { +CAN0_TX_MARK ,CAN0_RX_MARK , +}; + +static const unsigned int can1_data_pins[] = { +/* TX, RX */ +RCAR_GP_PIN (0 ,4 ),RCAR_GP_PIN (0 ,7 ), +}; + +static const unsigned int can1_data_mux[] = { +CAN1_TX_MARK ,CAN1_RX_MARK , +}; + +/* - CAN Clock -------------------------------------------------------------- */ +static const unsigned int can_clk_pins[] = { +/* CLK */ +RCAR_GP_PIN (0 ,14 ), +}; + +static const unsigned int can_clk_mux[] = { +CAN_CLK_MARK , +}; +/* - DU --------------------------------------------------------------------- */ static const unsigned int du_rgb666_pins[] = {/* R[7:2], G[7:2], B[7:2] */
@@ -3475,7 +3504,7 @@ static const unsigned int vin5_clk_b_mux[] = { };static const struct { -struct sh_pfc_pin_group common[238 ]; +struct sh_pfc_pin_group common[241 ];struct sh_pfc_pin_group automotive[0 ]; } pinmux_groups = { .common = {
@@ -3504,6 +3533,9 @@ static const struct {SH_PFC_PIN_GROUP (avb_avtp_pps),SH_PFC_PIN_GROUP (avb_avtp_match_a),SH_PFC_PIN_GROUP (avb_avtp_capture_a), +SH_PFC_PIN_GROUP (can0_data), +SH_PFC_PIN_GROUP (can1_data), +SH_PFC_PIN_GROUP (can_clk),SH_PFC_PIN_GROUP (du_rgb666),SH_PFC_PIN_GROUP (du_rgb888), SH_PFC_PIN_GROUP(du_clk_in_0),
@@ -3751,6 +3783,18 @@ static const char * const avb_groups[] = { "avb_avtp_capture_a", }; +static const char *const can0_groups[] = { +"can0_data" , +}; + +static const char *const can1_groups[] = { +"can1_data" , +}; + +static const char *const can_clk_groups[] = { +"can_clk" , +}; +static const char *const du_groups[] = {"du_rgb666" ,"du_rgb888" ,
@@ -4082,12 +4126,15 @@ static const char * const vin5_groups[] = { };static const struct { -struct sh_pfc_function common[41 ]; +struct sh_pfc_function common[44 ];struct sh_pfc_function automotive[0 ]; } pinmux_functions = { .common = {SH_PFC_FUNCTION (audio_clk),SH_PFC_FUNCTION (avb), +SH_PFC_FUNCTION (can0), +SH_PFC_FUNCTION (can1), +SH_PFC_FUNCTION (can_clk),SH_PFC_FUNCTION (du),SH_PFC_FUNCTION (hscif0),SH_PFC_FUNCTION (hscif1),
Signature · 1 line
2.7.4
PATCH 1/10 pinctrl: sh-pfc: r8a77990: Add CAN pins, groups and functions
Quoted 10 lines · Fabrizio Castro
From: Takeshi Kihara <[email protected]>
commit
c1e5bd286fe501992165608551f889ec69f5901aupstream.This patch adds CAN{0,1} pins, groups and functions to the R8A77990 SoC.
Signed-off-by Takeshi Kihara <[email protected]>Signed-off-by Marek Vasut <[email protected]>Signed-off-by Geert Uytterhoeven <[email protected]>Signed-off-by Fabrizio Castro <[email protected]>
This does not apply. My kernel still has:
Quoted 1 line
- struct
sh_pfc_pin_groupcommon[117];
while this expects... way higher number. I tried to look at pending patches in patchwork, that maybe if I tried to apply everything it would work, but could not get that to work, either.
Current status of the tree is at:
https://git.kernel.org/pub/scm/linux/kernel/git/cip/linux-cip.git/log/?h=linux-4.19.y-cip
Could the patches that depend on each other go into one series? If it is hard identifying what depends on what, maybe the best way forward is to create a big series on top of 64729dc0be4847961550cdcca4ddc66adf556aaa with all patches you have pending. Your patches seem to be in good shape, so applying it should not be a big deal.
Thanks and sorry for confusion,
Pavel
Quoted 10 lines
drivers/pinctrl/sh-pfc/pfc-r8a77990.c +1
-1@@ -3475,7 +3504,7 @@ static const unsigned int vin5_clk_b_mux[] = { };static const struct { -struct sh_pfc_pin_group common[238 ]; +struct sh_pfc_pin_group common[241 ];struct sh_pfc_pin_group automotive[0 ]; } pinmux_groups = { .common = {@@ -3504,6 +3533,9 @@ static const struct {
Signature · 2 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
PATCH 1/10 pinctrl: sh-pfc: r8a77990: Add CAN pins, groups and functions
Hello Pavel,
Thank you for your feedback.
Quoted 29 lines
-----Original Message-----
From: Pavel Machek <[email protected]>
Sent: 09 April 2019 22:04
To: Fabrizio Castro <[email protected]>
Cc: cip-dev at lists.cip-project.org; Biju Das <[email protected]>
Subject: Re: [cip-dev] [PATCH 4.19y 01/10] pinctrl: sh-pfc: r8a77990: Add CAN pins, groups and functionsQuoted 10 lines · Fabrizio Castro
From: Takeshi Kihara <[email protected]>
commit
c1e5bd286fe501992165608551f889ec69f5901aupstream.This patch adds CAN{0,1} pins, groups and functions to the R8A77990 SoC.
Signed-off-by Takeshi Kihara <[email protected]>Signed-off-by Marek Vasut <[email protected]>Signed-off-by Geert Uytterhoeven <[email protected]>Signed-off-by Fabrizio Castro <[email protected]>This does not apply. My kernel still has:
Quoted 1 line
- struct
sh_pfc_pin_groupcommon[117];while this expects... way higher number. I tried to look at pending patches in patchwork, that maybe if I tried to apply everything it would work, but could not get that to work, either.
Current status of the tree is at:
Quoted 7 lines
https://git.kernel.org/pub/scm/linux/kernel/git/cip/linux-cip.git/log/?h=linux-4.19.y-cip
Could the patches that depend on each other go into one series? If it is hard identifying what depends on what, maybe the best way forward is to create a big series on top of
64729dc0be4847961550cdcca4ddc66adf556aaawith all patches you have pending. Your patches seem to be in good shape, so applying it should not be a big deal.
I went through the emails on the cip-dev mailing list and I could find all the necessary patches this patch depends on, this patch applies cleanly once its dependencies have been applied, so perhaps we should do what you are suggesting, which is sending you another big series to apply on top of the current branch.
Thanks,
Fab
Quoted 20 lines
Thanks and sorry for confusion,
Paveldrivers/pinctrl/sh-pfc/pfc-r8a77990.c static const struct {
Quoted 10 lines
drivers/pinctrl/sh-pfc/pfc-r8a77990.c +1
-1@@ -3475,7 +3504,7 @@ static const unsigned int vin5_clk_b_mux[] = { };static const struct { -struct sh_pfc_pin_group common[238 ]; +struct sh_pfc_pin_group common[241 ];struct sh_pfc_pin_group automotive[0 ]; } pinmux_groups = { .common = {@@ -3504,6 +3533,9 @@ static const struct {--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
PATCH 1/10 pinctrl: sh-pfc: r8a77990: Add CAN pins, groups and functions
Hello Pavel,
Quoted 48 lines
-----Original Message-----
From: cip-dev-bounces at lists.cip-project.org <[email protected]> On Behalf Of Fabrizio Castro
Sent: 10 April 2019 10:17
To: Pavel Machek <[email protected]>
Cc: cip-dev at lists.cip-project.org; Biju Das <[email protected]>
Subject: Re: [cip-dev] [PATCH 4.19y 01/10] pinctrl: sh-pfc: r8a77990: Add CAN pins, groups and functionsHello Pavel,
Thank you for your feedback.
Quoted 29 lines
-----Original Message-----
From: Pavel Machek <[email protected]>
Sent: 09 April 2019 22:04
To: Fabrizio Castro <[email protected]>
Cc: cip-dev at lists.cip-project.org; Biju Das <[email protected]>
Subject: Re: [cip-dev] [PATCH 4.19y 01/10] pinctrl: sh-pfc: r8a77990: Add CAN pins, groups and functionsQuoted 10 lines · Fabrizio Castro
From: Takeshi Kihara <[email protected]>
commit
c1e5bd286fe501992165608551f889ec69f5901aupstream.This patch adds CAN{0,1} pins, groups and functions to the R8A77990 SoC.
Signed-off-by Takeshi Kihara <[email protected]>Signed-off-by Marek Vasut <[email protected]>Signed-off-by Geert Uytterhoeven <[email protected]>Signed-off-by Fabrizio Castro <[email protected]>This does not apply. My kernel still has:
Quoted 1 line
- struct
sh_pfc_pin_groupcommon[117];while this expects... way higher number. I tried to look at pending patches in patchwork, that maybe if I tried to apply everything it would work, but could not get that to work, either.
Current status of the tree is at:
Quoted 7 lines
https://git.kernel.org/pub/scm/linux/kernel/git/cip/linux-cip.git/log/?h=linux-4.19.y-cip
Could the patches that depend on each other go into one series? If it is hard identifying what depends on what, maybe the best way forward is to create a big series on top of
64729dc0be4847961550cdcca4ddc66adf556aaawith all patches you have pending. Your patches seem to be in good shape, so applying it should not be a big deal.
Quoted 5 lines
I went through the emails on the cip-dev mailing list and I could find all the necessary patches this patch depends on, this patch applies cleanly once its dependencies have been applied, so perhaps we should do what you are suggesting, which is sending you another big series to apply on top of the current branch.
Actually, that would create an even bigger confusion at this point, so I am going to wait for you guys to work this out for now.
Thanks,
Fab
Quoted 29 lines
Thanks,
FabQuoted 7 lines
Thanks and sorry for confusion,
PavelQuoted 3 lines
(quoted diff) +0
-0@@ -3475,7 +3504,7 @@ static const unsigned int vin5_clk_b_mux[] = { };Quoted 13 lines
drivers/pinctrl/sh-pfc/pfc-r8a77990.c static const struct {
Quoted 7 lines
drivers/pinctrl/sh-pfc/pfc-r8a77990.c +1
-1static const struct { -struct sh_pfc_pin_group common[238 ]; +struct sh_pfc_pin_group common[241 ];struct sh_pfc_pin_group automotive[0 ]; } pinmux_groups = { .common = {@@ -3504,6 +3533,9 @@ static const struct {--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany_______________________________________________
cip-dev mailing list
cip-dev at lists.cip-project.org
https://lists.cip-project.org/mailman/listinfo/cip-dev
[cip-dev] Renesas patches was Re: [PATCH 4.19y 01/10] pinctrl: sh-pfc: r8a77990: Add CAN pins, groups and functions
Hi!
Quoted 10 lines
Quoted 10 lines
Quoted 9 lines
Current status of the tree is at:
https://git.kernel.org/pub/scm/linux/kernel/git/cip/linux-cip.git/log/?h=linux-4.19.y-cip
Could the patches that depend on each other go into one series? If it is hard identifying what depends on what, maybe the best way forward is to create a big series on top of
64729dc0be4847961550cdcca4ddc66adf556aaawith all patches you have pending. Your patches seem to be in good shape, so applying it should not be a big deal.
Quoted 8 lines
Quoted 5 lines
I went through the emails on the cip-dev mailing list and I could find all the necessary patches this patch depends on, this patch applies cleanly once its dependencies have been applied, so perhaps we should do what you are suggesting, which is sending you another big series to apply on top of the current branch.
Actually, that would create an even bigger confusion at this point, so I am going to wait for you guys to work this out for now.
Good news -- I believe we managed to sort it out.
Tree at
https://git.kernel.org/pub/scm/linux/kernel/git/cip/linux-cip.git/log/?h=linux-4.19.y-cip
should now be up-to-date with your patches. If you could run any tests and verify things look sane, it would be great.
Best regards,
Pavel
Signature · 9 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 181 bytes Desc: Digital signature URL: <http://lists.cip-project.org/pipermail/cip-dev/attachments/20190412/5e806e8c/attachment.sig>
[cip-dev] Renesas patches was Re: [PATCH 4.19y 01/10] pinctrl: sh-pfc: r8a77990: Add CAN pins, groups and functions
Hello Pavel,
Quoted 28 lines
-----Original Message-----
From: Pavel Machek <[email protected]>
Sent: 12 April 2019 21:29
To: Fabrizio Castro <[email protected]>
Cc: Pavel Machek <[email protected]>; cip-dev at lists.cip-project.org; Biju Das <[email protected]>
Subject: Renesas patches was Re: [cip-dev] [PATCH 4.19y 01/10] pinctrl: sh-pfc: r8a77990: Add CAN pins, groups and functionsHi!
Quoted 10 lines
Quoted 10 lines
Quoted 9 lines
Current status of the tree is at:
https://git.kernel.org/pub/scm/linux/kernel/git/cip/linux-cip.git/log/?h=linux-4.19.y-cip
Could the patches that depend on each other go into one series? If it is hard identifying what depends on what, maybe the best way forward is to create a big series on top of
64729dc0be4847961550cdcca4ddc66adf556aaawith all patches you have pending. Your patches seem to be in good shape, so applying it should not be a big deal.Quoted 8 lines
Quoted 5 lines
I went through the emails on the cip-dev mailing list and I could find all the necessary patches this patch depends on, this patch applies cleanly once its dependencies have been applied, so perhaps we should do what you are suggesting, which is sending you another big series to apply on top of the current branch.
Actually, that would create an even bigger confusion at this point, so I am going to wait for you guys to work this out for now.
Quoted 8 lines
Good news -- I believe we managed to sort it out.
Tree at
https://git.kernel.org/pub/scm/linux/kernel/git/cip/linux-cip.git/log/?h=linux-4.19.y-cip
should now be up-to-date with your patches. If you could run any tests and verify things look sane, it would be great.
Thank you for your efforts! I can confirm all of the patches have been applied and things look sane.
Thanks,
Fab
Quoted 7 lines
Best regards,
Pavel--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
PATCH 1/10 pinctrl: sh-pfc: r8a77990: Add CAN pins, groups and functions
In reply to Fabrizio CastroHi, Fabrizio
Quoted 57 lines
-----Original Message-----
From: cip-dev-bounces at lists.cip-project.org [mailto:cip-dev-bounces at lists.cip-project.org] On Behalf Of Fabrizio Castro
Sent: Wednesday, April 10, 2019 6:17 PM
To: Pavel Machek <[email protected]>
Cc: cip-dev at lists.cip-project.org; Biju Das <[email protected]>
Subject: Re: [cip-dev] [PATCH 4.19y 01/10] pinctrl: sh-pfc: r8a77990:
Add CAN pins, groups and functionsHello Pavel,
Thank you for your feedback.
Quoted 8 lines
-----Original Message-----
From: Pavel Machek <[email protected]>
Sent: 09 April 2019 22:04
To: Fabrizio Castro <[email protected]>
Cc: cip-dev at lists.cip-project.org; Biju Das <[email protected]>
Subject: Re: [cip-dev] [PATCH 4.19y 01/10] pinctrl: sh-pfc: r8a77990:
Add CAN pins, groups and functionsQuoted 6 lines
Quoted 5 lines · Fabrizio Castro
From: Takeshi Kihara <[email protected]>
commit
c1e5bd286fe501992165608551f889ec69f5901aupstream.This patch adds CAN{0,1} pins, groups and functions to the R8A77990
SoC.
Quoted 8 lines
Quoted 5 lines
Signed-off-by Takeshi Kihara <[email protected]>Signed-off-by Marek Vasut <[email protected]>Signed-off-by Geert Uytterhoeven <[email protected]>Signed-off-by Fabrizio Castro <[email protected]>This does not apply. My kernel still has:
Quoted 9 lines
Quoted 1 line
- struct
sh_pfc_pin_groupcommon[117];while this expects... way higher number. I tried to look at pending patches in patchwork, that maybe if I tried to apply everything it would work, but could not get that to work, either.
Current status of the tree is at:
https://git.kernel.org/pub/scm/linux/kernel/git/cip/linux-cip.git/lo
g/Quoted 8 lines
?h=linux-4.19.y-cip
Could the patches that depend on each other go into one series? If it is hard identifying what depends on what, maybe the best way forward is to create a big series on top of
64729dc0be4847961550cdcca4ddc66adf556aaa
with all patches you have pending. Your patches seem to be in good shape, so applying it should not be a big deal.
Quoted 5 lines
I went through the emails on the cip-dev mailing list and I could find all the necessary patches this patch depends on, this patch applies cleanly once its dependencies have been applied, so perhaps we should do what you are suggesting, which is sending you another big series to apply on top of the current branch.
Pavel and I are reviewing the patch now.
Although we share patches, we have such a problem because we do not consider the dependencies of each series. The patch review by two people has just begun, so I think there are many problems. The kernel team will talk about this.
Pavel, do you have comment about this?
If possible, it would be helpful if you could write a patch series dependency on the cover letter of series.
Best regards,
Nobuhiro
Quoted 8 lines
Thanks,
FabQuoted 4 lines
Thanks and sorry for confusion,
Pavel
Best regards,
Nobuhiro
Quoted 21 lines
Quoted 1 line
Review static const unsigned int vin5_clk_b_mux[] =
Quoted 1 line
(quoted diff) +0
-0@@ -3475,7 +3504,7 @@ static const unsigned int vin5_clk_b_mux[] ={
Quoted 14 lines
drivers/pinctrl/sh-pfc/pfc-r8a77990.c static const struct {
Quoted 8 lines
drivers/pinctrl/sh-pfc/pfc-r8a77990.c +1
-1};static const struct { -struct sh_pfc_pin_group common[238 ]; +struct sh_pfc_pin_group common[241 ];struct sh_pfc_pin_group automotive[0 ]; } pinmux_groups = { .common = {@@ -3504,6 +3533,9 @@ static const struct {--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany_______________________________________________
cip-dev mailing list
cip-dev at lists.cip-project.org
https://lists.cip-project.org/mailman/listinfo/cip-dev
PATCH 1/10 pinctrl: sh-pfc: r8a77990: Add CAN pins, groups and functions
In reply to Fabrizio CastroQuoted 10 lines · Fabrizio Castro
From: Takeshi Kihara <[email protected]>
commit
c1e5bd286fe501992165608551f889ec69f5901aupstream.This patch adds CAN{0,1} pins, groups and functions to the R8A77990 SoC.
Signed-off-by Takeshi Kihara <[email protected]>Signed-off-by Marek Vasut <[email protected]>Signed-off-by Geert Uytterhoeven <[email protected]>Signed-off-by Fabrizio Castro <[email protected]>
Thanks, I applied the series.
Signature · 9 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 181 bytes Desc: Digital signature URL: <http://lists.cip-project.org/pipermail/cip-dev/attachments/20190412/4043378d/attachment.sig>
PATCH 2/10 pinctrl: sh-pfc: r8a77990: Add CAN FD pins, groups and functions
In reply to Fabrizio CastroFrom: Takeshi Kihara <[email protected]>
commit b5ff38f15c3e3f5533c530a725140e9994c6011d upstream.
This patch adds CAN FD{0,1} pins, groups and functions to the R8A77990 SoC.
--- drivers/pinctrl/sh-pfc/pfc-r8a77990.c | 39 +++++++++++++++++++++++++++++++++-- 1 file changed, 37 insertions(+), 2 deletions(-)
drivers/pinctrl/sh-pfc/pfc-r8a77990.c +37 -2
@@ -1567,6 +1567,25 @@ static const unsigned int can_clk_mux[] = { CAN_CLK_MARK, }; +/* - CAN FD --------------------------------------------------------------- */ +static const unsigned int canfd0_data_pins[] = { +/* TX, RX */ +RCAR_GP_PIN (0 ,12 ),RCAR_GP_PIN (0 ,13 ), +}; + +static const unsigned int canfd0_data_mux[] = { +CANFD0_TX_MARK ,CANFD0_RX_MARK , +}; + +static const unsigned int canfd1_data_pins[] = { +/* TX, RX */ +RCAR_GP_PIN (0 ,4 ),RCAR_GP_PIN (0 ,7 ), +}; + +static const unsigned int canfd1_data_mux[] = { +CANFD1_TX_MARK ,CANFD1_RX_MARK , +}; +/* - DU --------------------------------------------------------------------- */ static const unsigned int du_rgb666_pins[] = {/* R[7:2], G[7:2], B[7:2] */
@@ -3505,7 +3524,7 @@ static const unsigned int vin5_clk_b_mux[] = {static const struct {struct sh_pfc_pin_group common[241 ]; -struct sh_pfc_pin_group automotive[0 ]; +struct sh_pfc_pin_group automotive[2 ]; } pinmux_groups = { .common = {SH_PFC_PIN_GROUP (audio_clk_a),
@@ -3749,6 +3768,10 @@ static const struct {SH_PFC_PIN_GROUP (vin5_clkenb_a),SH_PFC_PIN_GROUP (vin5_clk_a ),SH_PFC_PIN_GROUP (vin5_clk_b ), + }, + .automotive = { +SH_PFC_PIN_GROUP (canfd0_data), +SH_PFC_PIN_GROUP (canfd1_data), } };
@@ -3795,6 +3818,14 @@ static const char * const can_clk_groups[] = { "can_clk", }; +static const char *const canfd0_groups[] = { +"canfd0_data" , +}; + +static const char *const canfd1_groups[] = { +"canfd1_data" , +}; +static const char *const du_groups[] = {"du_rgb666" ,"du_rgb888" ,
@@ -4127,7 +4158,7 @@ static const char * const vin5_groups[] = {static const struct {struct sh_pfc_function common[44 ]; -struct sh_pfc_function automotive[0 ]; +struct sh_pfc_function automotive[2 ]; } pinmux_functions = { .common = {SH_PFC_FUNCTION (audio_clk),
@@ -4174,6 +4205,10 @@ static const struct {SH_PFC_FUNCTION (usb30),SH_PFC_FUNCTION (vin4 ),SH_PFC_FUNCTION (vin5 ), + }, + .automotive = { +SH_PFC_FUNCTION (canfd0), +SH_PFC_FUNCTION (canfd1), } };
Signature · 1 line
2.7.4
PATCH 3/10 pinctrl: sh-pfc: r8a77990: Fix IOCTRL reg state after s2ram on R-Car E3
In reply to Fabrizio CastroFrom: Geert Uytterhoeven <[email protected]>
commit 117774fbe6beae3fd4f1fed5b7f596acdd90a2ed upstream.
Due to an interaction with commit 9f2b76a2db3c4387 ("pinctrl: sh-pfc:
r8a77990: Add R8A774C0 PFC support"), the state of the I/O Control Registers is saved/restored during s2ram on RZ/G2E, but not on R-Car E3. Hence on R-Car E3, SDHI voltage state is lost after system resume.
Fix this by registering the I/O Control Registers on R-Car E3, too.
--- drivers/pinctrl/sh-pfc/pfc-r8a77990.c | 1 + 1 file changed, 1 insertion(+)
drivers/pinctrl/sh-pfc/pfc-r8a77990.c +1 -0
@@ -5004,6 +5004,7 @@ const struct sh_pfc_soc_info r8a77990_pinmux_info = { .cfg_regs = pinmux_config_regs, .bias_regs = pinmux_bias_regs, + .ioctrl_regs = pinmux_ioctrl_regs, .pinmux_data = pinmux_data, .pinmux_data_size = ARRAY_SIZE(pinmux_data),
Signature · 1 line
2.7.4
PATCH 4/10 pinctrl: sh-pfc: r8a77990: Fix MOD_SEL0 SEL_I2C1 field width
In reply to Fabrizio CastroFrom: Geert Uytterhoeven <[email protected]>
commit 755a5b805fa7ff22e2934d67501efd92109f41ea upstream.
The SEL_I2C1 (MOD_SEL0[21:20]) field in Module Select Register 0 has a width of 2 bits, i.e. it allows programming one out of 4 different configurations.
However, the MOD_SEL0_21_20 macro contains 8 values instead of 4, overflowing into the subsequent fields in the register, and thus breaking the configuration of the latter.
Fix this by dropping the bogus last 4 values, including the non-existent SEL_I2C1_4 configuration.
--- drivers/pinctrl/sh-pfc/pfc-r8a77990.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/pinctrl/sh-pfc/pfc-r8a77990.c +1 -1
@@ -399,7 +399,7 @@ FM(IP12_31_28) IP12_31_28 FM(IP13_31_28) IP13_31_28 FM(IP14_31_28) IP14_31_28 FM#define MOD_SEL0_24 FM(SEL_HSCIF0_0) FM(SEL_HSCIF0_1)#define MOD_SEL0_23 FM(SEL_HSCIF1_0) FM(SEL_HSCIF1_1)#define MOD_SEL0_22 FM(SEL_HSCIF2_0) FM(SEL_HSCIF2_1) -#define MOD_SEL0_21_20 FM(SEL_I2C1_0) FM(SEL_I2C1_1) FM(SEL_I2C1_2) FM(SEL_I2C1_3) FM(SEL_I2C1_4) F_(0, 0) F_(0, 0) F_(0, 0) +#define MOD_SEL0_21_20 FM(SEL_I2C1_0) FM(SEL_I2C1_1) FM(SEL_I2C1_2) FM(SEL_I2C1_3)#define MOD_SEL0_19_18_17 FM(SEL_I2C2_0) FM(SEL_I2C2_1) FM(SEL_I2C2_2) FM(SEL_I2C2_3) FM(SEL_I2C2_4) F_(0, 0) F_(0, 0) F_(0, 0)#define MOD_SEL0_16 FM(SEL_NDFC_0) FM(SEL_NDFC_1)#define MOD_SEL0_15 FM(SEL_PWM0_0) FM(SEL_PWM0_1)
Signature · 1 line
2.7.4
PATCH 5/10 pinctrl: sh-pfc: r8a77990: Fix MOD_SEL0 bit3 when using TX0
In reply to Fabrizio CastroFrom: Takeshi Kihara <[email protected]>
commit 699c7d1346fbef69e60ca7647c50bbebc483d1c8 upstream.
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug 24, 2018, the MOD_SEL0 bit3 is set to 0 when TX0_A pin function is selected, and the MOD_SEL0 bit3 is set to 1 when TX0_B pin function is selected.
--- drivers/pinctrl/sh-pfc/pfc-r8a77990.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/pinctrl/sh-pfc/pfc-r8a77990.c +2 -2
@@ -1060,7 +1060,7 @@ static const u16 pinmux_data[] = {PINMUX_IPSR_GPSR (IP11_11_8 ,RIF1_SYNC ),PINMUX_IPSR_GPSR (IP11_11_8 ,TS_SCK1 ), -PINMUX_IPSR_GPSR (IP11_15_12 ,TX0_A ), +PINMUX_IPSR_MSEL (IP11_15_12 ,TX0_A ,SEL_SCIF0_0 ),PINMUX_IPSR_GPSR (IP11_15_12 ,HTX1_A ),PINMUX_IPSR_MSEL (IP11_15_12 ,SSI_WS2_A ,SEL_SSI2_0 ), PINMUX_IPSR_GPSR(IP11_15_12, RIF1_D0),
@@ -1170,7 +1170,7 @@ static const u16 pinmux_data[] = {PINMUX_IPSR_MSEL (IP13_19_16 ,SIM0_D_A ,SEL_SIMCARD_0 ),PINMUX_IPSR_GPSR (IP13_23_20 ,MLB_DAT ), -PINMUX_IPSR_GPSR (IP13_23_20 ,TX0_B ), +PINMUX_IPSR_MSEL (IP13_23_20 ,TX0_B ,SEL_SCIF0_1 ),PINMUX_IPSR_MSEL (IP13_23_20 ,RIF0_SYNC_A ,SEL_DRIF0_0 ), PINMUX_IPSR_GPSR(IP13_23_20, SIM0_CLK_A),
Signature · 1 line
2.7.4
PATCH 6/10 pinctrl: sh-pfc: r8a77990: Fix MOD_SEL0 bit2 when using RX2, TX2 and SCK2
In reply to Fabrizio CastroFrom: Takeshi Kihara <[email protected]>
commit 7219a4b645208734d45b1d30a4c35b6f09a0e9e6 upstream.
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug 24, 2018, the MOD_SEL0 bit2 is set when RX2_{A,B}, TX2_{A,B} and SCK2_A pin functions are selected.
--- drivers/pinctrl/sh-pfc/pfc-r8a77990.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-)
drivers/pinctrl/sh-pfc/pfc-r8a77990.c +5 -5
@@ -1099,7 +1099,7 @@ static const u16 pinmux_data[] = {PINMUX_IPSR_MSEL (IP12_3_0 ,SSI_WS9_B ,SEL_SSI9_1 ),PINMUX_IPSR_GPSR (IP12_3_0 ,AUDIO_CLKOUT3_B ), -PINMUX_IPSR_GPSR (IP12_7_4 ,SCK2_A ), +PINMUX_IPSR_MSEL (IP12_7_4 ,SCK2_A ,SEL_SCIF2_0 ),PINMUX_IPSR_MSEL (IP12_7_4 ,HSCK0_A ,SEL_HSCIF0_0 ),PINMUX_IPSR_MSEL (IP12_7_4 ,AUDIO_CLKB_A ,SEL_ADGB_0 ), PINMUX_IPSR_GPSR(IP12_7_4, CTS1_N),
@@ -1107,14 +1107,14 @@ static const u16 pinmux_data[] = {PINMUX_IPSR_MSEL (IP12_7_4 ,REMOCON_A ,SEL_REMOCON_0 ),PINMUX_IPSR_MSEL (IP12_7_4 ,SCIF_CLK_B ,SEL_SCIF_1 ), -PINMUX_IPSR_GPSR (IP12_11_8 ,TX2_A ), +PINMUX_IPSR_MSEL (IP12_11_8 ,TX2_A ,SEL_SCIF2_0 ),PINMUX_IPSR_MSEL (IP12_11_8 ,HRX0_A ,SEL_HSCIF0_0 ),PINMUX_IPSR_GPSR (IP12_11_8 ,AUDIO_CLKOUT2_A ),PINMUX_IPSR_MSEL (IP12_11_8 ,SCL1_A ,SEL_I2C1_0 ),PINMUX_IPSR_MSEL (IP12_11_8 ,FSO_CFE_0_N_A ,SEL_FSO_0 ),PINMUX_IPSR_GPSR (IP12_11_8 ,TS_SDEN1 ), -PINMUX_IPSR_GPSR (IP12_15_12 ,RX2_A ), +PINMUX_IPSR_MSEL (IP12_15_12 ,RX2_A ,SEL_SCIF2_0 ),PINMUX_IPSR_GPSR (IP12_15_12 ,HTX0_A ),PINMUX_IPSR_GPSR (IP12_15_12 ,AUDIO_CLKOUT3_A ), PINMUX_IPSR_MSEL(IP12_15_12, SDA1_A, SEL_I2C1_0),
@@ -1126,11 +1126,11 @@ static const u16 pinmux_data[] = {PINMUX_IPSR_GPSR (IP12_23_20 ,MSIOF0_RXD ),PINMUX_IPSR_GPSR (IP12_23_20 ,SSI_WS78 ), -PINMUX_IPSR_GPSR (IP12_23_20 ,TX2_B ), +PINMUX_IPSR_MSEL (IP12_23_20 ,TX2_B ,SEL_SCIF2_1 ),PINMUX_IPSR_GPSR (IP12_27_24 ,MSIOF0_TXD ),PINMUX_IPSR_GPSR (IP12_27_24 ,SSI_SDATA7 ), -PINMUX_IPSR_GPSR (IP12_27_24 ,RX2_B ), +PINMUX_IPSR_MSEL (IP12_27_24 ,RX2_B ,SEL_SCIF2_1 ),PINMUX_IPSR_GPSR (IP12_31_28 ,MSIOF0_SYNC ), PINMUX_IPSR_GPSR(IP12_31_28, AUDIO_CLKOUT_B),
Signature · 1 line
2.7.4
PATCH 7/10 pinctrl: sh-pfc: r8a77990: Fix MOD_SEL bit numbering
In reply to Fabrizio CastroFrom: Takeshi Kihara <[email protected]>
commit 3e3eebeacad79bda8a9664c86c04f5201e86fece upstream.
MOD_SEL register bit numbering was different from R-Car E3 SoC and R-Car H3/M3-[WN] SoCs.
MOD_SEL 1-bit H3/M3-[WN] E3 =============== ========== ===== Set Value = H'0 b'0 b'0 Set Value = H'1 b'1 b'1
MOD_SEL 2-bits H3/M3-[WN] E3 =============== ========== ===== Set Value = H'0 b'00 b'00 Set Value = H'1 b'01 b'10 Set Value = H'2 b'10 b'01 Set Value = H'3 b'11 b'11
MOD_SEL 3-bits H3/M3-[WN] E3 =============== ========== ===== Set Value = H'0 b'000 b'000 Set Value = H'1 b'001 b'100 Set Value = H'2 b'010 b'010 Set Value = H'3 b'011 b'110 Set Value = H'4 b'100 b'001 Set Value = H'5 b'101 b'101 Set Value = H'6 b'110 b'011 Set Value = H'7 b'111 b'111
This patch replaces the #define name and value of MOD_SEL.
--- drivers/pinctrl/sh-pfc/pfc-r8a77990.c | 32 ++++++++++++++++++-------------- 1 file changed, 18 insertions(+), 14 deletions(-)
drivers/pinctrl/sh-pfc/pfc-r8a77990.c +18 -14
@@ -391,29 +391,33 @@ FM(IP12_23_20) IP12_23_20 FM(IP13_23_20) IP13_23_20 FM(IP14_23_20) IP14_23_20 FM FM(IP12_27_24) IP12_27_24 FM(IP13_27_24) IP13_27_24 FM(IP14_27_24) IP14_27_24 FM(IP15_27_24) IP15_27_24 \ FM(IP12_31_28) IP12_31_28 FM(IP13_31_28) IP13_31_28 FM(IP14_31_28) IP14_31_28 FM(IP15_31_28) IP15_31_28 +/* The bit numbering in MOD_SEL fields is reversed */ +#define REV4(f0, f1, f2, f3) f0 f2 f1 f3 +#define REV8(f0, f1, f2, f3, f4, f5, f6, f7) f0 f4 f2 f6 f1 f5 f3 f7 + /* MOD_SEL0 */ /* 0 */ /* 1 */ /* 2 */ /* 3 */ /* 4 */ /* 5 */ /* 6 */ /* 7 */ -#define MOD_SEL0_30_29 FM(SEL_ADGB_0) FM(SEL_ADGB_1) FM(SEL_ADGB_2) F_(0, 0) +#define MOD_SEL0_30_29 REV4(FM(SEL_ADGB_0), FM(SEL_ADGB_1), FM(SEL_ADGB_2), F_(0, 0)) #define MOD_SEL0_28 FM(SEL_DRIF0_0) FM(SEL_DRIF0_1) -#define MOD_SEL0_27_26 FM(SEL_FM_0) FM(SEL_FM_1) FM(SEL_FM_2) F_(0, 0) +#define MOD_SEL0_27_26 REV4(FM(SEL_FM_0), FM(SEL_FM_1), FM(SEL_FM_2), F_(0, 0)) #define MOD_SEL0_25 FM(SEL_FSO_0) FM(SEL_FSO_1) #define MOD_SEL0_24 FM(SEL_HSCIF0_0) FM(SEL_HSCIF0_1) #define MOD_SEL0_23 FM(SEL_HSCIF1_0) FM(SEL_HSCIF1_1) #define MOD_SEL0_22 FM(SEL_HSCIF2_0) FM(SEL_HSCIF2_1) -#define MOD_SEL0_21_20 FM(SEL_I2C1_0) FM(SEL_I2C1_1) FM(SEL_I2C1_2) FM(SEL_I2C1_3) -#define MOD_SEL0_19_18_17 FM(SEL_I2C2_0) FM(SEL_I2C2_1) FM(SEL_I2C2_2) FM(SEL_I2C2_3) FM(SEL_I2C2_4) F_(0, 0) F_(0, 0) F_(0, 0) +#define MOD_SEL0_21_20 REV4(FM(SEL_I2C1_0), FM(SEL_I2C1_1), FM(SEL_I2C1_2), FM(SEL_I2C1_3)) +#define MOD_SEL0_19_18_17 REV8(FM(SEL_I2C2_0), FM(SEL_I2C2_1), FM(SEL_I2C2_2), FM(SEL_I2C2_3), FM(SEL_I2C2_4), F_(0, 0), F_(0, 0), F_(0, 0)) #define MOD_SEL0_16 FM(SEL_NDFC_0) FM(SEL_NDFC_1) #define MOD_SEL0_15 FM(SEL_PWM0_0) FM(SEL_PWM0_1) #define MOD_SEL0_14 FM(SEL_PWM1_0) FM(SEL_PWM1_1) -#define MOD_SEL0_13_12 FM(SEL_PWM2_0) FM(SEL_PWM2_1) FM(SEL_PWM2_2) F_(0, 0) -#define MOD_SEL0_11_10 FM(SEL_PWM3_0) FM(SEL_PWM3_1) FM(SEL_PWM3_2) F_(0, 0) +#define MOD_SEL0_13_12 REV4(FM(SEL_PWM2_0), FM(SEL_PWM2_1), FM(SEL_PWM2_2), F_(0, 0)) +#define MOD_SEL0_11_10 REV4(FM(SEL_PWM3_0), FM(SEL_PWM3_1), FM(SEL_PWM3_2), F_(0, 0)) #define MOD_SEL0_9 FM(SEL_PWM4_0) FM(SEL_PWM4_1) #define MOD_SEL0_8 FM(SEL_PWM5_0) FM(SEL_PWM5_1) #define MOD_SEL0_7 FM(SEL_PWM6_0) FM(SEL_PWM6_1) -#define MOD_SEL0_6_5 FM(SEL_REMOCON_0) FM(SEL_REMOCON_1) FM(SEL_REMOCON_2) F_(0, 0) +#define MOD_SEL0_6_5 REV4(FM(SEL_REMOCON_0), FM(SEL_REMOCON_1), FM(SEL_REMOCON_2), F_(0, 0)) #define MOD_SEL0_4 FM(SEL_SCIF_0) FM(SEL_SCIF_1) #define MOD_SEL0_3 FM(SEL_SCIF0_0) FM(SEL_SCIF0_1) #define MOD_SEL0_2 FM(SEL_SCIF2_0) FM(SEL_SCIF2_1) -#define MOD_SEL0_1_0 FM(SEL_SPEED_PULSE_IF_0) FM(SEL_SPEED_PULSE_IF_1) FM(SEL_SPEED_PULSE_IF_2) F_(0, 0) +#define MOD_SEL0_1_0 REV4(FM(SEL_SPEED_PULSE_IF_0), FM(SEL_SPEED_PULSE_IF_1), FM(SEL_SPEED_PULSE_IF_2), F_(0, 0)) /* MOD_SEL1 */ /* 0 */ /* 1 */ /* 2 */ /* 3 */ /* 4 */ /* 5 */ /* 6 */ /* 7 */ #define MOD_SEL1_31 FM(SEL_SIMCARD_0) FM(SEL_SIMCARD_1)
@@ -422,18 +426,18 @@ FM(IP12_31_28) IP12_31_28 FM(IP13_31_28) IP13_31_28 FM(IP14_31_28) IP14_31_28 FM#define MOD_SEL1_28 FM(SEL_USB_20_CH0_0) FM(SEL_USB_20_CH0_1)#define MOD_SEL1_26 FM(SEL_DRIF2_0) FM(SEL_DRIF2_1)#define MOD_SEL1_25 FM(SEL_DRIF3_0) FM(SEL_DRIF3_1) -#define MOD_SEL1_24_23_22 FM(SEL_HSCIF3_0) FM(SEL_HSCIF3_1) FM(SEL_HSCIF3_2) FM(SEL_HSCIF3_3) FM(SEL_HSCIF3_4) F_(0, 0) F_(0, 0) F_(0, 0) -#define MOD_SEL1_21_20_19 FM(SEL_HSCIF4_0) FM(SEL_HSCIF4_1) FM(SEL_HSCIF4_2) FM(SEL_HSCIF4_3) FM(SEL_HSCIF4_4) F_(0, 0) F_(0, 0) F_(0, 0) +#define MOD_SEL1_24_23_22 REV8(FM(SEL_HSCIF3_0), FM(SEL_HSCIF3_1), FM(SEL_HSCIF3_2), FM(SEL_HSCIF3_3), FM(SEL_HSCIF3_4), F_(0, 0), F_(0, 0), F_(0, 0)) +#define MOD_SEL1_21_20_19 REV8(FM(SEL_HSCIF4_0), FM(SEL_HSCIF4_1), FM(SEL_HSCIF4_2), FM(SEL_HSCIF4_3), FM(SEL_HSCIF4_4), F_(0, 0), F_(0, 0), F_(0, 0))#define MOD_SEL1_18 FM(SEL_I2C6_0) FM(SEL_I2C6_1)#define MOD_SEL1_17 FM(SEL_I2C7_0) FM(SEL_I2C7_1)#define MOD_SEL1_16 FM(SEL_MSIOF2_0) FM(SEL_MSIOF2_1)#define MOD_SEL1_15 FM(SEL_MSIOF3_0) FM(SEL_MSIOF3_1) -#define MOD_SEL1_14_13 FM(SEL_SCIF3_0) FM(SEL_SCIF3_1) FM(SEL_SCIF3_2) F_(0, 0) -#define MOD_SEL1_12_11 FM(SEL_SCIF4_0) FM(SEL_SCIF4_1) FM(SEL_SCIF4_2) F_(0, 0) -#define MOD_SEL1_10_9 FM(SEL_SCIF5_0) FM(SEL_SCIF5_1) FM(SEL_SCIF5_2) F_(0, 0) +#define MOD_SEL1_14_13 REV4(FM(SEL_SCIF3_0), FM(SEL_SCIF3_1), FM(SEL_SCIF3_2), F_(0, 0)) +#define MOD_SEL1_12_11 REV4(FM(SEL_SCIF4_0), FM(SEL_SCIF4_1), FM(SEL_SCIF4_2), F_(0, 0)) +#define MOD_SEL1_10_9 REV4(FM(SEL_SCIF5_0), FM(SEL_SCIF5_1), FM(SEL_SCIF5_2), F_(0, 0))#define MOD_SEL1_8 FM(SEL_VIN4_0) FM(SEL_VIN4_1)#define MOD_SEL1_7 FM(SEL_VIN5_0) FM(SEL_VIN5_1) -#define MOD_SEL1_6_5 FM(SEL_ADGC_0) FM(SEL_ADGC_1) FM(SEL_ADGC_2) F_(0, 0) +#define MOD_SEL1_6_5 REV4(FM(SEL_ADGC_0), FM(SEL_ADGC_1), FM(SEL_ADGC_2), F_(0, 0))#define MOD_SEL1_4 FM(SEL_SSI9_0) FM(SEL_SSI9_1)#define PINMUX_MOD_SELS \
Signature · 1 line
2.7.4
PATCH 8/10 pinctrl: sh-pfc: r8a77990: GP6_9 does not have pull-down capability
In reply to Fabrizio CastroFrom: Geert Uytterhoeven <[email protected]>
commit f7d8b568e204d295bf0e780cea10cab1f84be31e upstream.
Hence remove the SH_PFC_PIN_CFG_PULL_DOWN flag from the GP6_9 GPIO description.
--- drivers/pinctrl/sh-pfc/pfc-r8a77990.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-)
drivers/pinctrl/sh-pfc/pfc-r8a77990.c +10 -1
@@ -30,7 +30,16 @@PORT_GP_CFG_1 (3 ,15 , fn, sfx,CFG_FLAGS ), \PORT_GP_CFG_11 (4 , fn, sfx,CFG_FLAGS |SH_PFC_PIN_CFG_IO_VOLTAGE ), \PORT_GP_CFG_20 (5 , fn, sfx,CFG_FLAGS ), \ -PORT_GP_CFG_18 (6 , fn, sfx,CFG_FLAGS ) +PORT_GP_CFG_9 (6 , fn, sfx,CFG_FLAGS ), \ +PORT_GP_CFG_1 (6 ,9 , fn, sfx,SH_PFC_PIN_CFG_PULL_UP ), \ +PORT_GP_CFG_1 (6 ,10 , fn, sfx,CFG_FLAGS ), \ +PORT_GP_CFG_1 (6 ,11 , fn, sfx,CFG_FLAGS ), \ +PORT_GP_CFG_1 (6 ,12 , fn, sfx,CFG_FLAGS ), \ +PORT_GP_CFG_1 (6 ,13 , fn, sfx,CFG_FLAGS ), \ +PORT_GP_CFG_1 (6 ,14 , fn, sfx,CFG_FLAGS ), \ +PORT_GP_CFG_1 (6 ,15 , fn, sfx,CFG_FLAGS ), \ +PORT_GP_CFG_1 (6 ,16 , fn, sfx,CFG_FLAGS ), \ +PORT_GP_CFG_1 (6 ,17 , fn, sfx,CFG_FLAGS )/* * F_() : just information * FM() : macro for FN_xxx / xxx_MARK
Signature · 1 line
2.7.4
PATCH 9/10 pinctrl: sh-pfc: r8a77990: Add TMU pins, groups and functions
In reply to Fabrizio CastroFrom: Takeshi Kihara <[email protected]>
commit 16978e7d40f73bed462ca991ce3565d133b0c6cd upstream.
This patch adds TMU TCLK{1,2} pins, groups and functions to the R8A77990 SoC.
--- drivers/pinctrl/sh-pfc/pfc-r8a77990.c | 53 +++++++++++++++++++++++++++++++++-- 1 file changed, 51 insertions(+), 2 deletions(-)
drivers/pinctrl/sh-pfc/pfc-r8a77990.c +51 -2
@@ -3256,6 +3256,43 @@ static const unsigned int ssi9_ctrl_b_mux[] = { SSI_SCK9_B_MARK, SSI_WS9_B_MARK, }; +/* - TMU -------------------------------------------------------------------- */ +static const unsigned int tmu_tclk1_a_pins[] = { +/* TCLK */ +RCAR_GP_PIN (3 ,12 ), +}; + +static const unsigned int tmu_tclk1_a_mux[] = { +TCLK1_A_MARK , +}; + +static const unsigned int tmu_tclk1_b_pins[] = { +/* TCLK */ +RCAR_GP_PIN (5 ,17 ), +}; + +static const unsigned int tmu_tclk1_b_mux[] = { +TCLK1_B_MARK , +}; + +static const unsigned int tmu_tclk2_a_pins[] = { +/* TCLK */ +RCAR_GP_PIN (3 ,13 ), +}; + +static const unsigned int tmu_tclk2_a_mux[] = { +TCLK2_A_MARK , +}; + +static const unsigned int tmu_tclk2_b_pins[] = { +/* TCLK */ +RCAR_GP_PIN (5 ,18 ), +}; + +static const unsigned int tmu_tclk2_b_mux[] = { +TCLK2_B_MARK , +}; +/* - USB0 ------------------------------------------------------------------- */ static const unsigned int usb0_a_pins[] = {/* PWEN, OVC */
@@ -3536,7 +3573,7 @@ static const unsigned int vin5_clk_b_mux[] = { };static const struct { -struct sh_pfc_pin_group common[241 ]; +struct sh_pfc_pin_group common[245 ];struct sh_pfc_pin_group automotive[2 ]; } pinmux_groups = { .common = {
@@ -3748,6 +3785,10 @@ static const struct {SH_PFC_PIN_GROUP (ssi9_data),SH_PFC_PIN_GROUP (ssi9_ctrl_a),SH_PFC_PIN_GROUP (ssi9_ctrl_b), +SH_PFC_PIN_GROUP (tmu_tclk1_a), +SH_PFC_PIN_GROUP (tmu_tclk1_b), +SH_PFC_PIN_GROUP (tmu_tclk2_a), +SH_PFC_PIN_GROUP (tmu_tclk2_b),SH_PFC_PIN_GROUP (usb0_a),SH_PFC_PIN_GROUP (usb0_b), SH_PFC_PIN_GROUP(usb0_id),
@@ -4124,6 +4165,13 @@ static const char * const ssi_groups[] = { "ssi9_ctrl_b", }; +static const char *const tmu_groups[] = { +"tmu_tclk1_a" , +"tmu_tclk1_b" , +"tmu_tclk2_a" , +"tmu_tclk2_b" , +}; +static const char *const usb0_groups[] = {"usb0_a" ,"usb0_b" ,
@@ -4170,7 +4218,7 @@ static const char * const vin5_groups[] = { };static const struct { -struct sh_pfc_function common[44 ]; +struct sh_pfc_function common[45 ];struct sh_pfc_function automotive[2 ]; } pinmux_functions = { .common = {
@@ -4214,6 +4262,7 @@ static const struct {SH_PFC_FUNCTION (sdhi1),SH_PFC_FUNCTION (sdhi3),SH_PFC_FUNCTION (ssi), +SH_PFC_FUNCTION (tmu),SH_PFC_FUNCTION (usb0),SH_PFC_FUNCTION (usb30), SH_PFC_FUNCTION(vin4),
Signature · 1 line
2.7.4
PATCH 10/10 pinctrl: sh-pfc: r8a77990: Add DRIF pins, groups and functions
In reply to Fabrizio CastroFrom: Takeshi Kihara <[email protected]>
commit fdbbd6b74c9278f65302af113e73cf61d36d3037 upstream.
This patch adds DRIF{0,1,2,3} pins, groups and functions to the R8A77990 SoC.
--- drivers/pinctrl/sh-pfc/pfc-r8a77990.c | 255 +++++++++++++++++++++++++++++++++- 1 file changed, 253 insertions(+), 2 deletions(-)
drivers/pinctrl/sh-pfc/pfc-r8a77990.c +253 -2
@@ -1599,6 +1599,199 @@ static const unsigned int canfd1_data_mux[] = { CANFD1_TX_MARK, CANFD1_RX_MARK, }; +/* - DRIF0 --------------------------------------------------------------- */ +static const unsigned int drif0_ctrl_a_pins[] = { +/* CLK, SYNC */ +RCAR_GP_PIN (5 ,7 ),RCAR_GP_PIN (5 ,19 ), +}; + +static const unsigned int drif0_ctrl_a_mux[] = { +RIF0_CLK_A_MARK ,RIF0_SYNC_A_MARK , +}; + +static const unsigned int drif0_data0_a_pins[] = { +/* D0 */ +RCAR_GP_PIN (5 ,17 ), +}; + +static const unsigned int drif0_data0_a_mux[] = { +RIF0_D0_A_MARK , +}; + +static const unsigned int drif0_data1_a_pins[] = { +/* D1 */ +RCAR_GP_PIN (5 ,18 ), +}; + +static const unsigned int drif0_data1_a_mux[] = { +RIF0_D1_A_MARK , +}; + +static const unsigned int drif0_ctrl_b_pins[] = { +/* CLK, SYNC */ +RCAR_GP_PIN (3 ,12 ),RCAR_GP_PIN (3 ,15 ), +}; + +static const unsigned int drif0_ctrl_b_mux[] = { +RIF0_CLK_B_MARK ,RIF0_SYNC_B_MARK , +}; + +static const unsigned int drif0_data0_b_pins[] = { +/* D0 */ +RCAR_GP_PIN (3 ,13 ), +}; + +static const unsigned int drif0_data0_b_mux[] = { +RIF0_D0_B_MARK , +}; + +static const unsigned int drif0_data1_b_pins[] = { +/* D1 */ +RCAR_GP_PIN (3 ,14 ), +}; + +static const unsigned int drif0_data1_b_mux[] = { +RIF0_D1_B_MARK , +}; + +/* - DRIF1 --------------------------------------------------------------- */ +static const unsigned int drif1_ctrl_pins[] = { +/* CLK, SYNC */ +RCAR_GP_PIN (5 ,4 ),RCAR_GP_PIN (5 ,1 ), +}; + +static const unsigned int drif1_ctrl_mux[] = { +RIF1_CLK_MARK ,RIF1_SYNC_MARK , +}; + +static const unsigned int drif1_data0_pins[] = { +/* D0 */ +RCAR_GP_PIN (5 ,2 ), +}; + +static const unsigned int drif1_data0_mux[] = { +RIF1_D0_MARK , +}; + +static const unsigned int drif1_data1_pins[] = { +/* D1 */ +RCAR_GP_PIN (5 ,3 ), +}; + +static const unsigned int drif1_data1_mux[] = { +RIF1_D1_MARK , +}; + +/* - DRIF2 --------------------------------------------------------------- */ +static const unsigned int drif2_ctrl_a_pins[] = { +/* CLK, SYNC */ +RCAR_GP_PIN (2 ,6 ),RCAR_GP_PIN (2 ,7 ), +}; + +static const unsigned int drif2_ctrl_a_mux[] = { +RIF2_CLK_A_MARK ,RIF2_SYNC_A_MARK , +}; + +static const unsigned int drif2_data0_a_pins[] = { +/* D0 */ +RCAR_GP_PIN (2 ,8 ), +}; + +static const unsigned int drif2_data0_a_mux[] = { +RIF2_D0_A_MARK , +}; + +static const unsigned int drif2_data1_a_pins[] = { +/* D1 */ +RCAR_GP_PIN (2 ,9 ), +}; + +static const unsigned int drif2_data1_a_mux[] = { +RIF2_D1_A_MARK , +}; + +static const unsigned int drif2_ctrl_b_pins[] = { +/* CLK, SYNC */ +RCAR_GP_PIN (1 ,4 ),RCAR_GP_PIN (1 ,5 ), +}; + +static const unsigned int drif2_ctrl_b_mux[] = { +RIF2_CLK_B_MARK ,RIF2_SYNC_B_MARK , +}; + +static const unsigned int drif2_data0_b_pins[] = { +/* D0 */ +RCAR_GP_PIN (1 ,6 ), +}; + +static const unsigned int drif2_data0_b_mux[] = { +RIF2_D0_B_MARK , +}; + +static const unsigned int drif2_data1_b_pins[] = { +/* D1 */ +RCAR_GP_PIN (1 ,7 ), +}; + +static const unsigned int drif2_data1_b_mux[] = { +RIF2_D1_B_MARK , +}; + +/* - DRIF3 --------------------------------------------------------------- */ +static const unsigned int drif3_ctrl_a_pins[] = { +/* CLK, SYNC */ +RCAR_GP_PIN (2 ,10 ),RCAR_GP_PIN (2 ,11 ), +}; + +static const unsigned int drif3_ctrl_a_mux[] = { +RIF3_CLK_A_MARK ,RIF3_SYNC_A_MARK , +}; + +static const unsigned int drif3_data0_a_pins[] = { +/* D0 */ +RCAR_GP_PIN (2 ,12 ), +}; + +static const unsigned int drif3_data0_a_mux[] = { +RIF3_D0_A_MARK , +}; + +static const unsigned int drif3_data1_a_pins[] = { +/* D1 */ +RCAR_GP_PIN (2 ,13 ), +}; + +static const unsigned int drif3_data1_a_mux[] = { +RIF3_D1_A_MARK , +}; + +static const unsigned int drif3_ctrl_b_pins[] = { +/* CLK, SYNC */ +RCAR_GP_PIN (0 ,8 ),RCAR_GP_PIN (0 ,9 ), +}; + +static const unsigned int drif3_ctrl_b_mux[] = { +RIF3_CLK_B_MARK ,RIF3_SYNC_B_MARK , +}; + +static const unsigned int drif3_data0_b_pins[] = { +/* D0 */ +RCAR_GP_PIN (0 ,10 ), +}; + +static const unsigned int drif3_data0_b_mux[] = { +RIF3_D0_B_MARK , +}; + +static const unsigned int drif3_data1_b_pins[] = { +/* D1 */ +RCAR_GP_PIN (0 ,11 ), +}; + +static const unsigned int drif3_data1_b_mux[] = { +RIF3_D1_B_MARK , +}; +/* - DU --------------------------------------------------------------------- */ static const unsigned int du_rgb666_pins[] = {/* R[7:2], G[7:2], B[7:2] */
@@ -3574,7 +3767,7 @@ static const unsigned int vin5_clk_b_mux[] = {static const struct {struct sh_pfc_pin_group common[245 ]; -struct sh_pfc_pin_group automotive[2 ]; +struct sh_pfc_pin_group automotive[23 ]; } pinmux_groups = { .common = {SH_PFC_PIN_GROUP (audio_clk_a),
@@ -3826,6 +4019,27 @@ static const struct { .automotive = {SH_PFC_PIN_GROUP (canfd0_data),SH_PFC_PIN_GROUP (canfd1_data), +SH_PFC_PIN_GROUP (drif0_ctrl_a), +SH_PFC_PIN_GROUP (drif0_data0_a), +SH_PFC_PIN_GROUP (drif0_data1_a), +SH_PFC_PIN_GROUP (drif0_ctrl_b), +SH_PFC_PIN_GROUP (drif0_data0_b), +SH_PFC_PIN_GROUP (drif0_data1_b), +SH_PFC_PIN_GROUP (drif1_ctrl), +SH_PFC_PIN_GROUP (drif1_data0), +SH_PFC_PIN_GROUP (drif1_data1), +SH_PFC_PIN_GROUP (drif2_ctrl_a), +SH_PFC_PIN_GROUP (drif2_data0_a), +SH_PFC_PIN_GROUP (drif2_data1_a), +SH_PFC_PIN_GROUP (drif2_ctrl_b), +SH_PFC_PIN_GROUP (drif2_data0_b), +SH_PFC_PIN_GROUP (drif2_data1_b), +SH_PFC_PIN_GROUP (drif3_ctrl_a), +SH_PFC_PIN_GROUP (drif3_data0_a), +SH_PFC_PIN_GROUP (drif3_data1_a), +SH_PFC_PIN_GROUP (drif3_ctrl_b), +SH_PFC_PIN_GROUP (drif3_data0_b), + SH_PFC_PIN_GROUP(drif3_data1_b), } };
@@ -3880,6 +4094,39 @@ static const char * const canfd1_groups[] = { "canfd1_data", }; +static const char *const drif0_groups[] = { +"drif0_ctrl_a" , +"drif0_data0_a" , +"drif0_data1_a" , +"drif0_ctrl_b" , +"drif0_data0_b" , +"drif0_data1_b" , +}; + +static const char *const drif1_groups[] = { +"drif1_ctrl" , +"drif1_data0" , +"drif1_data1" , +}; + +static const char *const drif2_groups[] = { +"drif2_ctrl_a" , +"drif2_data0_a" , +"drif2_data1_a" , +"drif2_ctrl_b" , +"drif2_data0_b" , +"drif2_data1_b" , +}; + +static const char *const drif3_groups[] = { +"drif3_ctrl_a" , +"drif3_data0_a" , +"drif3_data1_a" , +"drif3_ctrl_b" , +"drif3_data0_b" , +"drif3_data1_b" , +}; +static const char *const du_groups[] = {"du_rgb666" ,"du_rgb888" ,
@@ -4219,7 +4466,7 @@ static const char * const vin5_groups[] = {static const struct {struct sh_pfc_function common[45 ]; -struct sh_pfc_function automotive[2 ]; +struct sh_pfc_function automotive[6 ]; } pinmux_functions = { .common = {SH_PFC_FUNCTION (audio_clk),
@@ -4271,6 +4518,10 @@ static const struct { .automotive = {SH_PFC_FUNCTION (canfd0),SH_PFC_FUNCTION (canfd1), +SH_PFC_FUNCTION (drif0), +SH_PFC_FUNCTION (drif1), +SH_PFC_FUNCTION (drif2), + SH_PFC_FUNCTION(drif3), } };
Signature · 1 line
2.7.4