sunxi: Enable EMAC on A83T boards using Realtek RTL8211E PHY
Subsystems (3)
Chen-Yu Tsai
maintainercover sunxi: Enable EMAC on A83T boards using Realtek RTL8211E PHY
From: Chen-Yu Tsai <[email protected]>
(Resending yet again with correct email address now subscribed
and with proper cover letter subject. Sorry for the noise.)
Hi everyone,
This series enables EMAC (Ethernet controller) on two A83T boards, the Cubietruck Plus and Bananapi M3.
A couple of changes are required to the clock definitions to make the compiler happy, as it hasn't been coverted to use the common CLK and DM_RESET framework. These changes are not used in the A83T code path.
The other two patches enable the sun8i-emac and Realtek PHY driver in their respective defconfigs. The device trees already have the EMAC enabled.
Since these are compile time issues, all patches should go through the same tree.
Regards
ChenYu
Chen-Yu Tsai (4):
sunxi: Fix compilation of sun8i-emac for A83T
net: sun8i-emac: Fix compilation for A83T
sunxi: Enable EMAC on the Cubietruck Plus
sunxi: Enable EMAC on the Bananapi M3
arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h | 4 ++++ configs/Cubietruck_plus_defconfig | 2 ++ configs/Sinovoip_BPI_M3_defconfig | 2 ++ drivers/net/sun8i_emac.c | 3 +++ 4 files changed, 11 insertions(+)
Signature · 1 line
2.20.1
Chen-Yu Tsai
maintainerPATCH 1/4 sunxi: Fix compilation of sun8i-emac for A83T
From: Chen-Yu Tsai <[email protected]>
The A83T has its own clock header file and clock control module structure, unlike H3/A64/R40 which share a common one. As such some of the SoC specific fields or macros are undefined when building U-boot for A83T.
Add dummy entries to the clock control module structure to make the compiler happy. The code path using these fields is unused for A83T in the driver.
---
arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h | 4 ++++ 1 file changed, 4 insertions(+)
arch/arm/include/asm/arch-sunxi/clock_sun8i_a83t.h +4 -0
@@ -124,6 +124,10 @@ struct sunxi_ccm_reg {u32 ahb_reset3_cfg;/* 0x2d0 AHB1 Reset 3 config */ u32 reserved32;/* 0x2d4 */ u32 apb2_reset_cfg;/* 0x2d8 BUS Reset 4 config */ + +/* the following exist only to make sun8i-emac happy */ +u32 gmac_clk_cfg; +u32 bus_gate4; };/* apb2 bit field */
Signature · 1 line
2.20.1
Chen-Yu Tsai
maintainerPATCH 2/4 net: sun8i-emac: Fix compilation for A83T
In reply to Chen-Yu TsaiFrom: Chen-Yu Tsai <[email protected]>
The A83T has its own clock header file and clock control module structure, unlike H3/A64/R40 which share a common one. As such some of the SoC specific fields or macros are undefined when building U-boot for A83T.
Define the AHB_RESET_OFFSET_EPHY macro if it isn't already defined to make the compiler happy. The code path including this macro is unused in the driver for A83T.
---
This patch should go in with the others through the sunxi tree, not independently through the net tree.
drivers/net/sun8i_emac.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/net/sun8i_emac.c +3 -0
@@ -68,6 +68,9 @@#define CONFIG_MDIO_TIMEOUT (3 * CONFIG_SYS_HZ)#define AHB_GATE_OFFSET_EPHY 0 +#ifndef AHB_RESET_OFFSET_EPHY +#define AHB_RESET_OFFSET_EPHY 2 +#endif /* IO mux settings */ #define SUN8I_IOMUX_H3 2
Signature · 1 line
2.20.1
Chen-Yu Tsai
maintainerPATCH 3/4 sunxi: Enable EMAC on the Cubietruck Plus
In reply to Chen-Yu TsaiFrom: Chen-Yu Tsai <[email protected]>
The Cubietruck Plus has an RTL8211E PHY connected to the EMAC using RGMII. The PHY is powered by DLDO4 @ 3.3V, while the I/O pins are powered by DLDO3 @ 2.5V.
This patch enables the EMAC and Realtek PHY drivers in the defconfig. The device tree file already has the EMAC enabled.
---
configs/Cubietruck_plus_defconfig | 2 ++ 1 file changed, 2 insertions(+)
configs/Cubietruck_plus_defconfig +2 -0
@@ -20,6 +20,8 @@ CONFIG_CONSOLE_MUX=y # CONFIG_SPL_DOS_PARTITION is not set # CONFIG_SPL_EFI_PARTITION is not set CONFIG_DEFAULT_DEVICE_TREE="sun8i-a83t-cubietruck-plus" +CONFIG_PHY_REALTEK=y +CONFIG_SUN8I_EMAC=y CONFIG_AXP_DLDO3_VOLT=2500 CONFIG_AXP_DLDO4_VOLT=3300 CONFIG_AXP_FLDO1_VOLT=1200
Signature · 1 line
2.20.1
Chen-Yu Tsai
maintainerPATCH 4/4 sunxi: Enable EMAC on the Bananapi M3
In reply to Chen-Yu TsaiFrom: Chen-Yu Tsai <[email protected]>
The Bananapi M3 has an RTL8211E PHY connected to the EMAC using RGMII. The PHY is powered by DCDC1 through SW @ 3.3V.
This patch enables the EMAC and Realtek PHY drivers in the defconfig. The device tree file already has the EMAC enabled.
---
configs/Sinovoip_BPI_M3_defconfig | 2 ++ 1 file changed, 2 insertions(+)
configs/Sinovoip_BPI_M3_defconfig +2 -0
@@ -21,6 +21,8 @@ CONFIG_CONSOLE_MUX=y # CONFIG_SPL_DOS_PARTITION is not set # CONFIG_SPL_EFI_PARTITION is not set CONFIG_DEFAULT_DEVICE_TREE="sun8i-a83t-bananapi-m3" +CONFIG_PHY_REALTEK=y +CONFIG_SUN8I_EMAC=y CONFIG_AXP_DCDC5_VOLT=1200 CONFIG_AXP_DLDO3_VOLT=2500 CONFIG_AXP_SW_ON=y
Signature · 1 line
2.20.1
cover sunxi: Enable EMAC on A83T boards using Realtek RTL8211E PHY
In reply to Chen-Yu TsaiHi,
Quoted 26 lines · Chen-Yu Tsai
From: Chen-Yu Tsai <[email protected]>
(Resending yet again with correct email address now subscribed
and with proper cover letter subject. Sorry for the noise.)Hi everyone,
This series enables EMAC (Ethernet controller) on two A83T boards, the Cubietruck Plus and Bananapi M3.
A couple of changes are required to the clock definitions to make the compiler happy, as it hasn't been coverted to use the common CLK and
DM_RESETframework. These changes are not used in the A83T code path.The other two patches enable the sun8i-emac and Realtek PHY driver in their respective defconfigs. The device trees already have the EMAC enabled.
Since these are compile time issues, all patches should go through the same tree.
Regards
ChenYu
Quoted 5 lines
Chen-Yu Tsai (4):
sunxi: Fix compilation of sun8i-emac for A83T
net: sun8i-emac: Fix compilation for A83T
sunxi: Enable EMAC on the Cubietruck Plus
sunxi: Enable EMAC on the Bananapi M3
We have EPHY clock and reset support via respective framework [1] would you rebase these changes on top this.
[1] http://git.denx.de/?p=u-boot-sunxi.git;a=commitdiff;h=6b2ccabee2368d059513a9be37c0ffaa4a47ec99
Chen-Yu Tsai
maintainercover sunxi: Enable EMAC on A83T boards using Realtek RTL8211E PHY
Quoted 36 lines · Jagan Teki
Hi,
Quoted 26 lines · Chen-Yu Tsai
From: Chen-Yu Tsai <[email protected]>
(Resending yet again with correct email address now subscribed
and with proper cover letter subject. Sorry for the noise.)Hi everyone,
This series enables EMAC (Ethernet controller) on two A83T boards, the Cubietruck Plus and Bananapi M3.
A couple of changes are required to the clock definitions to make the compiler happy, as it hasn't been coverted to use the common CLK and
DM_RESETframework. These changes are not used in the A83T code path.The other two patches enable the sun8i-emac and Realtek PHY driver in their respective defconfigs. The device trees already have the EMAC enabled.
Since these are compile time issues, all patches should go through the same tree.
Regards
ChenYuQuoted 5 lines
Chen-Yu Tsai (4):
sunxi: Fix compilation of sun8i-emac for A83T
net: sun8i-emac: Fix compilation for A83T
sunxi: Enable EMAC on the Cubietruck Plus
sunxi: Enable EMAC on the Bananapi M3
Quoted 4 lines
We have EPHY clock and reset support via respective framework [1] would you rebase these changes on top this.
[1] http://git.denx.de/?p=u-boot-sunxi.git;a=commitdiff;h=6b2ccabee2368d059513a9be37c0ffaa4a47ec99
Lovely! I'll throw the clock register bit patches out and rework the other stuff.
Does anyone else have these boards for testing though? I'm away from my boards for the next two weeks (which is past the merge window).
ChenYu
Chen-Yu Tsai
maintainercover sunxi: Enable EMAC on A83T boards using Realtek RTL8211E PHY
Quoted 41 lines · Chen-Yu Tsai
Quoted 39 lines · Jagan Teki
Hi,
Quoted 26 lines · Chen-Yu Tsai
From: Chen-Yu Tsai <[email protected]>
(Resending yet again with correct email address now subscribed
and with proper cover letter subject. Sorry for the noise.)Hi everyone,
This series enables EMAC (Ethernet controller) on two A83T boards, the Cubietruck Plus and Bananapi M3.
A couple of changes are required to the clock definitions to make the compiler happy, as it hasn't been coverted to use the common CLK and
DM_RESETframework. These changes are not used in the A83T code path.The other two patches enable the sun8i-emac and Realtek PHY driver in their respective defconfigs. The device trees already have the EMAC enabled.
Since these are compile time issues, all patches should go through the same tree.
Regards
ChenYuQuoted 5 lines
Chen-Yu Tsai (4):
sunxi: Fix compilation of sun8i-emac for A83T
net: sun8i-emac: Fix compilation for A83T
sunxi: Enable EMAC on the Cubietruck Plus
sunxi: Enable EMAC on the Bananapi M3We have EPHY clock and reset support via respective framework [1] would you rebase these changes on top this.
Quoted 7 lines
Quoted 1 line
[1] http://git.denx.de/?p=u-boot-sunxi.git;a=commitdiff;h=6b2ccabee2368d059513a9be37c0ffaa4a47ec99
Lovely! I'll throw the clock register bit patches out and rework the other stuff.
Does anyone else have these boards for testing though? I'm away from my boards for the next two weeks (which is past the merge window).
Looks like the EPHY clock and resets weren't converted. So it still needs some sort of fix to build. Do you have anything in the works regarding EPHY?
ChenYu
Chen-Yu Tsai
maintainercover sunxi: Enable EMAC on A83T boards using Realtek RTL8211E PHY
Quoted 48 lines · Chen-Yu Tsai
Quoted 46 lines · Chen-Yu Tsai
Quoted 36 lines · Jagan Teki
Hi,
Quoted 26 lines · Chen-Yu Tsai
From: Chen-Yu Tsai <[email protected]>
(Resending yet again with correct email address now subscribed
and with proper cover letter subject. Sorry for the noise.)Hi everyone,
This series enables EMAC (Ethernet controller) on two A83T boards, the Cubietruck Plus and Bananapi M3.
A couple of changes are required to the clock definitions to make the compiler happy, as it hasn't been coverted to use the common CLK and
DM_RESETframework. These changes are not used in the A83T code path.The other two patches enable the sun8i-emac and Realtek PHY driver in their respective defconfigs. The device trees already have the EMAC enabled.
Since these are compile time issues, all patches should go through the same tree.
Regards
ChenYuQuoted 5 lines
Chen-Yu Tsai (4):
sunxi: Fix compilation of sun8i-emac for A83T
net: sun8i-emac: Fix compilation for A83T
sunxi: Enable EMAC on the Cubietruck Plus
sunxi: Enable EMAC on the Bananapi M3Quoted 4 lines
We have EPHY clock and reset support via respective framework [1] would you rebase these changes on top this.
[1] http://git.denx.de/?p=u-boot-sunxi.git;a=commitdiff;h=6b2ccabee2368d059513a9be37c0ffaa4a47ec99
Lovely! I'll throw the clock register bit patches out and rework the other stuff.
Quoted 6 lines
Quoted 2 lines
Does anyone else have these boards for testing though? I'm away from my boards for the next two weeks (which is past the merge window).
Looks like the EPHY clock and resets weren't converted. So it still needs some sort of fix to build. Do you have anything in the works regarding EPHY?
Looks like sunxi/next has the answer. And the new defconfigs build cleanly. Would you like to me respin on top with RFT? It doesn't actually matter what branch the defconfig patches are based on since they apply cleanly to either branch.
ChenYu
cover sunxi: Enable EMAC on A83T boards using Realtek RTL8211E PHY
Quoted 53 lines · Chen-Yu Tsai
Quoted 51 lines · Chen-Yu Tsai
Quoted 48 lines · Chen-Yu Tsai
Quoted 36 lines · Jagan Teki
Hi,
Quoted 26 lines · Chen-Yu Tsai
From: Chen-Yu Tsai <[email protected]>
(Resending yet again with correct email address now subscribed
and with proper cover letter subject. Sorry for the noise.)Hi everyone,
This series enables EMAC (Ethernet controller) on two A83T boards, the Cubietruck Plus and Bananapi M3.
A couple of changes are required to the clock definitions to make the compiler happy, as it hasn't been coverted to use the common CLK and
DM_RESETframework. These changes are not used in the A83T code path.The other two patches enable the sun8i-emac and Realtek PHY driver in their respective defconfigs. The device trees already have the EMAC enabled.
Since these are compile time issues, all patches should go through the same tree.
Regards
ChenYuQuoted 5 lines
Chen-Yu Tsai (4):
sunxi: Fix compilation of sun8i-emac for A83T
net: sun8i-emac: Fix compilation for A83T
sunxi: Enable EMAC on the Cubietruck Plus
sunxi: Enable EMAC on the Bananapi M3Quoted 4 lines
We have EPHY clock and reset support via respective framework [1] would you rebase these changes on top this.
[1] http://git.denx.de/?p=u-boot-sunxi.git;a=commitdiff;h=6b2ccabee2368d059513a9be37c0ffaa4a47ec99
Lovely! I'll throw the clock register bit patches out and rework the other stuff.
Does anyone else have these boards for testing though? I'm away from my boards for the next two weeks (which is past the merge window).
Quoted 8 lines
Quoted 3 lines
Looks like the EPHY clock and resets weren't converted. So it still needs some sort of fix to build. Do you have anything in the works regarding EPHY?
Looks like sunxi/next has the answer. And the new defconfigs build cleanly. Would you like to me respin on top with RFT? It doesn't actually matter what branch the defconfig patches are based on since they apply cleanly to either branch.
Yes, ie what I'm thinking.
BTW: the existing code doesn't enable the use_internal_phy for H3_EMAC, any idea? ie what I was thought and prepared this EPHY CLK and RESET support enabled it which indeed enabling use_internal_phy
Chen-Yu Tsai
maintainercover sunxi: Enable EMAC on A83T boards using Realtek RTL8211E PHY
Quoted 64 lines · Jagan Teki
Quoted 53 lines · Chen-Yu Tsai
Quoted 51 lines · Chen-Yu Tsai
Quoted 48 lines · Chen-Yu Tsai
Quoted 36 lines · Jagan Teki
Hi,
Quoted 26 lines · Chen-Yu Tsai
From: Chen-Yu Tsai <[email protected]>
(Resending yet again with correct email address now subscribed
and with proper cover letter subject. Sorry for the noise.)Hi everyone,
This series enables EMAC (Ethernet controller) on two A83T boards, the Cubietruck Plus and Bananapi M3.
A couple of changes are required to the clock definitions to make the compiler happy, as it hasn't been coverted to use the common CLK and
DM_RESETframework. These changes are not used in the A83T code path.The other two patches enable the sun8i-emac and Realtek PHY driver in their respective defconfigs. The device trees already have the EMAC enabled.
Since these are compile time issues, all patches should go through the same tree.
Regards
ChenYuQuoted 5 lines
Chen-Yu Tsai (4):
sunxi: Fix compilation of sun8i-emac for A83T
net: sun8i-emac: Fix compilation for A83T
sunxi: Enable EMAC on the Cubietruck Plus
sunxi: Enable EMAC on the Bananapi M3Quoted 4 lines
We have EPHY clock and reset support via respective framework [1] would you rebase these changes on top this.
[1] http://git.denx.de/?p=u-boot-sunxi.git;a=commitdiff;h=6b2ccabee2368d059513a9be37c0ffaa4a47ec99
Lovely! I'll throw the clock register bit patches out and rework the other stuff.
Does anyone else have these boards for testing though? I'm away from my boards for the next two weeks (which is past the merge window).
Quoted 8 lines
Quoted 3 lines
Looks like the EPHY clock and resets weren't converted. So it still needs some sort of fix to build. Do you have anything in the works regarding EPHY?
Looks like sunxi/next has the answer. And the new defconfigs build cleanly. Would you like to me respin on top with RFT? It doesn't actually matter what branch the defconfig patches are based on since they apply cleanly to either branch.
Quoted 5 lines
Yes, ie what I'm thinking.
BTW: the existing code doesn't enable the
use_internal_phyforH3_EMAC, any idea? ie what I was thought and prepared this EPHY CLK and RESET support enabled it which indeed enablinguse_internal_phy
The original code had:
if (priv->variant == H3_EMAC) {
int parent = fdt_parent_offset(gd->fdt_blob, offset);
if (parent >= 0 &&
!fdt_node_check_compatible(gd->fdt_blob, parent,
"allwinner,sun8i-h3-mdio-internal"))
priv->use_internal_phy = true;
}in sun8i_emac_eth_ofdata_to_platdata(), which I think is what you're asking about?
ChenYu
cover sunxi: Enable EMAC on A83T boards using Realtek RTL8211E PHY
Quoted 83 lines · Chen-Yu Tsai
Quoted 64 lines · Jagan Teki
Quoted 53 lines · Chen-Yu Tsai
Quoted 51 lines · Chen-Yu Tsai
Quoted 48 lines · Chen-Yu Tsai
Quoted 36 lines · Jagan Teki
Hi,
Quoted 26 lines · Chen-Yu Tsai
From: Chen-Yu Tsai <[email protected]>
(Resending yet again with correct email address now subscribed
and with proper cover letter subject. Sorry for the noise.)Hi everyone,
This series enables EMAC (Ethernet controller) on two A83T boards, the Cubietruck Plus and Bananapi M3.
A couple of changes are required to the clock definitions to make the compiler happy, as it hasn't been coverted to use the common CLK and
DM_RESETframework. These changes are not used in the A83T code path.The other two patches enable the sun8i-emac and Realtek PHY driver in their respective defconfigs. The device trees already have the EMAC enabled.
Since these are compile time issues, all patches should go through the same tree.
Regards
ChenYuQuoted 5 lines
Chen-Yu Tsai (4):
sunxi: Fix compilation of sun8i-emac for A83T
net: sun8i-emac: Fix compilation for A83T
sunxi: Enable EMAC on the Cubietruck Plus
sunxi: Enable EMAC on the Bananapi M3Quoted 4 lines
We have EPHY clock and reset support via respective framework [1] would you rebase these changes on top this.
[1] http://git.denx.de/?p=u-boot-sunxi.git;a=commitdiff;h=6b2ccabee2368d059513a9be37c0ffaa4a47ec99
Lovely! I'll throw the clock register bit patches out and rework the other stuff.
Does anyone else have these boards for testing though? I'm away from my boards for the next two weeks (which is past the merge window).
Quoted 8 lines
Quoted 3 lines
Looks like the EPHY clock and resets weren't converted. So it still needs some sort of fix to build. Do you have anything in the works regarding EPHY?
Looks like sunxi/next has the answer. And the new defconfigs build cleanly. Would you like to me respin on top with RFT? It doesn't actually matter what branch the defconfig patches are based on since they apply cleanly to either branch.
Quoted 5 lines
Yes, ie what I'm thinking.
BTW: the existing code doesn't enable the
use_internal_phyforH3_EMAC, any idea? ie what I was thought and prepared this EPHY CLK and RESET support enabled it which indeed enablinguse_internal_phyThe original code had:
if (priv->variant == H3_EMAC) { int parent = fdt_parent_offset(gd->fdt_blob, offset); if (parent >= 0 && !fdt_node_check_compatible(gd->fdt_blob, parent, "allwinner,sun8i-h3-mdio-internal")) priv->use_internal_phy = true; }
Quoted 2 lines
in
sun8i_emac_eth_ofdata_to_platdata(), which I think is what you're asking about?
Yes, the same but priv->use_internal_phy not assign to true at the end.
Chen-Yu Tsai
maintainercover sunxi: Enable EMAC on A83T boards using Realtek RTL8211E PHY
Quoted 85 lines · Jagan Teki
Quoted 83 lines · Chen-Yu Tsai
Quoted 64 lines · Jagan Teki
Quoted 53 lines · Chen-Yu Tsai
Quoted 51 lines · Chen-Yu Tsai
Quoted 48 lines · Chen-Yu Tsai
Quoted 36 lines · Jagan Teki
Hi,
Quoted 26 lines · Chen-Yu Tsai
From: Chen-Yu Tsai <[email protected]>
(Resending yet again with correct email address now subscribed
and with proper cover letter subject. Sorry for the noise.)Hi everyone,
This series enables EMAC (Ethernet controller) on two A83T boards, the Cubietruck Plus and Bananapi M3.
A couple of changes are required to the clock definitions to make the compiler happy, as it hasn't been coverted to use the common CLK and
DM_RESETframework. These changes are not used in the A83T code path.The other two patches enable the sun8i-emac and Realtek PHY driver in their respective defconfigs. The device trees already have the EMAC enabled.
Since these are compile time issues, all patches should go through the same tree.
Regards
ChenYuQuoted 5 lines
Chen-Yu Tsai (4):
sunxi: Fix compilation of sun8i-emac for A83T
net: sun8i-emac: Fix compilation for A83T
sunxi: Enable EMAC on the Cubietruck Plus
sunxi: Enable EMAC on the Bananapi M3Quoted 4 lines
We have EPHY clock and reset support via respective framework [1] would you rebase these changes on top this.
[1] http://git.denx.de/?p=u-boot-sunxi.git;a=commitdiff;h=6b2ccabee2368d059513a9be37c0ffaa4a47ec99
Lovely! I'll throw the clock register bit patches out and rework the other stuff.
Does anyone else have these boards for testing though? I'm away from my boards for the next two weeks (which is past the merge window).
Quoted 8 lines
Quoted 3 lines
Looks like the EPHY clock and resets weren't converted. So it still needs some sort of fix to build. Do you have anything in the works regarding EPHY?
Looks like sunxi/next has the answer. And the new defconfigs build cleanly. Would you like to me respin on top with RFT? It doesn't actually matter what branch the defconfig patches are based on since they apply cleanly to either branch.
Quoted 5 lines
Yes, ie what I'm thinking.
BTW: the existing code doesn't enable the
use_internal_phyforH3_EMAC, any idea? ie what I was thought and prepared this EPHY CLK and RESET support enabled it which indeed enablinguse_internal_phyThe original code had:
if (priv->variant == H3_EMAC) { int parent = fdt_parent_offset(gd->fdt_blob, offset); if (parent >= 0 && !fdt_node_check_compatible(gd->fdt_blob, parent, "allwinner,sun8i-h3-mdio-internal")) priv->use_internal_phy = true; }
Quoted 4 lines
Quoted 2 lines
in
sun8i_emac_eth_ofdata_to_platdata(), which I think is what you're asking about?Yes, the same but
priv->use_internal_phynot assign to true at the end.
Doesn't the last line set it to true?
I'm not sure what you're asking. Are you asking when you should set priv->use_internal_phy?
ChenYu
cover sunxi: Enable EMAC on A83T boards using Realtek RTL8211E PHY
Quoted 90 lines · Chen-Yu Tsai
Quoted 88 lines · Jagan Teki
Quoted 85 lines · Chen-Yu Tsai
Quoted 64 lines · Jagan Teki
Quoted 53 lines · Chen-Yu Tsai
Quoted 51 lines · Chen-Yu Tsai
Quoted 48 lines · Chen-Yu Tsai
Quoted 36 lines · Jagan Teki
Hi,
Quoted 26 lines · Chen-Yu Tsai
From: Chen-Yu Tsai <[email protected]>
(Resending yet again with correct email address now subscribed
and with proper cover letter subject. Sorry for the noise.)Hi everyone,
This series enables EMAC (Ethernet controller) on two A83T boards, the Cubietruck Plus and Bananapi M3.
A couple of changes are required to the clock definitions to make the compiler happy, as it hasn't been coverted to use the common CLK and
DM_RESETframework. These changes are not used in the A83T code path.The other two patches enable the sun8i-emac and Realtek PHY driver in their respective defconfigs. The device trees already have the EMAC enabled.
Since these are compile time issues, all patches should go through the same tree.
Regards
ChenYuQuoted 5 lines
Chen-Yu Tsai (4):
sunxi: Fix compilation of sun8i-emac for A83T
net: sun8i-emac: Fix compilation for A83T
sunxi: Enable EMAC on the Cubietruck Plus
sunxi: Enable EMAC on the Bananapi M3Quoted 4 lines
We have EPHY clock and reset support via respective framework [1] would you rebase these changes on top this.
[1] http://git.denx.de/?p=u-boot-sunxi.git;a=commitdiff;h=6b2ccabee2368d059513a9be37c0ffaa4a47ec99
Lovely! I'll throw the clock register bit patches out and rework the other stuff.
Does anyone else have these boards for testing though? I'm away from my boards for the next two weeks (which is past the merge window).
Quoted 8 lines
Quoted 3 lines
Looks like the EPHY clock and resets weren't converted. So it still needs some sort of fix to build. Do you have anything in the works regarding EPHY?
Looks like sunxi/next has the answer. And the new defconfigs build cleanly. Would you like to me respin on top with RFT? It doesn't actually matter what branch the defconfig patches are based on since they apply cleanly to either branch.
Quoted 5 lines
Yes, ie what I'm thinking.
BTW: the existing code doesn't enable the
use_internal_phyforH3_EMAC, any idea? ie what I was thought and prepared this EPHY CLK and RESET support enabled it which indeed enablinguse_internal_phyThe original code had:
if (priv->variant == H3_EMAC) { int parent = fdt_parent_offset(gd->fdt_blob, offset); if (parent >= 0 && !fdt_node_check_compatible(gd->fdt_blob, parent, "allwinner,sun8i-h3-mdio-internal")) priv->use_internal_phy = true; }in
sun8i_emac_eth_ofdata_to_platdata(), which I think is what you're asking about?
Quoted 6 lines
Quoted 1 line
Yes, the same but
priv->use_internal_phynot assign to true at the end.Doesn't the last line set it to true?
I'm not sure what you're asking. Are you asking when you should set
priv->use_internal_phy?
Inside if statement seems to failed and which intern not setting use_internal_phy to true. so at the end priv->use_internal_phy is false (as default) is it the proper behavior, I thought it is wrong.
Chen-Yu Tsai
maintainercover sunxi: Enable EMAC on A83T boards using Realtek RTL8211E PHY
Quoted 94 lines · Jagan Teki
Quoted 92 lines · Chen-Yu Tsai
Quoted 89 lines · Jagan Teki
Quoted 83 lines · Chen-Yu Tsai
Quoted 64 lines · Jagan Teki
Quoted 53 lines · Chen-Yu Tsai
Quoted 51 lines · Chen-Yu Tsai
Quoted 48 lines · Chen-Yu Tsai
Quoted 36 lines · Jagan Teki
Hi,
Quoted 26 lines · Chen-Yu Tsai
From: Chen-Yu Tsai <[email protected]>
(Resending yet again with correct email address now subscribed
and with proper cover letter subject. Sorry for the noise.)Hi everyone,
This series enables EMAC (Ethernet controller) on two A83T boards, the Cubietruck Plus and Bananapi M3.
A couple of changes are required to the clock definitions to make the compiler happy, as it hasn't been coverted to use the common CLK and
DM_RESETframework. These changes are not used in the A83T code path.The other two patches enable the sun8i-emac and Realtek PHY driver in their respective defconfigs. The device trees already have the EMAC enabled.
Since these are compile time issues, all patches should go through the same tree.
Regards
ChenYuQuoted 5 lines
Chen-Yu Tsai (4):
sunxi: Fix compilation of sun8i-emac for A83T
net: sun8i-emac: Fix compilation for A83T
sunxi: Enable EMAC on the Cubietruck Plus
sunxi: Enable EMAC on the Bananapi M3Quoted 4 lines
We have EPHY clock and reset support via respective framework [1] would you rebase these changes on top this.
[1] http://git.denx.de/?p=u-boot-sunxi.git;a=commitdiff;h=6b2ccabee2368d059513a9be37c0ffaa4a47ec99
Lovely! I'll throw the clock register bit patches out and rework the other stuff.
Does anyone else have these boards for testing though? I'm away from my boards for the next two weeks (which is past the merge window).
Quoted 8 lines
Quoted 3 lines
Looks like the EPHY clock and resets weren't converted. So it still needs some sort of fix to build. Do you have anything in the works regarding EPHY?
Looks like sunxi/next has the answer. And the new defconfigs build cleanly. Would you like to me respin on top with RFT? It doesn't actually matter what branch the defconfig patches are based on since they apply cleanly to either branch.
Quoted 5 lines
Yes, ie what I'm thinking.
BTW: the existing code doesn't enable the
use_internal_phyforH3_EMAC, any idea? ie what I was thought and prepared this EPHY CLK and RESET support enabled it which indeed enablinguse_internal_phyThe original code had:
if (priv->variant == H3_EMAC) { int parent = fdt_parent_offset(gd->fdt_blob, offset); if (parent >= 0 && !fdt_node_check_compatible(gd->fdt_blob, parent, "allwinner,sun8i-h3-mdio-internal")) priv->use_internal_phy = true; }Quoted 2 lines
in
sun8i_emac_eth_ofdata_to_platdata(), which I think is what you're asking about?Yes, the same but
priv->use_internal_phynot assign to true at the end.
Quoted 8 lines
Quoted 4 lines
Doesn't the last line set it to true?
I'm not sure what you're asking. Are you asking when you should set
priv->use_internal_phy?Inside if statement seems to failed and which intern not setting
use_internal_phyto true. so at the endpriv->use_internal_phyis false (as default) is it the proper behavior, I thought it is wrong.
Not sure why it fails. fdt_node_check_compatible will return 0 if the node lists the given compatible string. And fdt_parent_offset returns >= 0 for a valid offset. The logic looks correct:
If the PHY node's parent is compatible with "allwinner,sun8i-h3-mdio-internal", set priv->use_internal_phy = true.
ChenYu
cover sunxi: Enable EMAC on A83T boards using Realtek RTL8211E PHY
Quoted 105 lines · Chen-Yu Tsai
Quoted 94 lines · Jagan Teki
Quoted 92 lines · Chen-Yu Tsai
Quoted 89 lines · Jagan Teki
Quoted 83 lines · Chen-Yu Tsai
Quoted 64 lines · Jagan Teki
Quoted 53 lines · Chen-Yu Tsai
Quoted 51 lines · Chen-Yu Tsai
Quoted 48 lines · Chen-Yu Tsai
Quoted 36 lines · Jagan Teki
Hi,
Quoted 26 lines · Chen-Yu Tsai
From: Chen-Yu Tsai <[email protected]>
(Resending yet again with correct email address now subscribed
and with proper cover letter subject. Sorry for the noise.)Hi everyone,
This series enables EMAC (Ethernet controller) on two A83T boards, the Cubietruck Plus and Bananapi M3.
A couple of changes are required to the clock definitions to make the compiler happy, as it hasn't been coverted to use the common CLK and
DM_RESETframework. These changes are not used in the A83T code path.The other two patches enable the sun8i-emac and Realtek PHY driver in their respective defconfigs. The device trees already have the EMAC enabled.
Since these are compile time issues, all patches should go through the same tree.
Regards
ChenYuQuoted 5 lines
Chen-Yu Tsai (4):
sunxi: Fix compilation of sun8i-emac for A83T
net: sun8i-emac: Fix compilation for A83T
sunxi: Enable EMAC on the Cubietruck Plus
sunxi: Enable EMAC on the Bananapi M3Quoted 4 lines
We have EPHY clock and reset support via respective framework [1] would you rebase these changes on top this.
[1] http://git.denx.de/?p=u-boot-sunxi.git;a=commitdiff;h=6b2ccabee2368d059513a9be37c0ffaa4a47ec99
Lovely! I'll throw the clock register bit patches out and rework the other stuff.
Does anyone else have these boards for testing though? I'm away from my boards for the next two weeks (which is past the merge window).
Quoted 8 lines
Quoted 3 lines
Looks like the EPHY clock and resets weren't converted. So it still needs some sort of fix to build. Do you have anything in the works regarding EPHY?
Looks like sunxi/next has the answer. And the new defconfigs build cleanly. Would you like to me respin on top with RFT? It doesn't actually matter what branch the defconfig patches are based on since they apply cleanly to either branch.
Quoted 5 lines
Yes, ie what I'm thinking.
BTW: the existing code doesn't enable the
use_internal_phyforH3_EMAC, any idea? ie what I was thought and prepared this EPHY CLK and RESET support enabled it which indeed enablinguse_internal_phyThe original code had:
if (priv->variant == H3_EMAC) { int parent = fdt_parent_offset(gd->fdt_blob, offset); if (parent >= 0 && !fdt_node_check_compatible(gd->fdt_blob, parent, "allwinner,sun8i-h3-mdio-internal")) priv->use_internal_phy = true; }Quoted 2 lines
in
sun8i_emac_eth_ofdata_to_platdata(), which I think is what you're asking about?Yes, the same but
priv->use_internal_phynot assign to true at the end.Quoted 8 lines
Quoted 4 lines
Doesn't the last line set it to true?
I'm not sure what you're asking. Are you asking when you should set
priv->use_internal_phy?Inside if statement seems to failed and which intern not setting
use_internal_phyto true. so at the endpriv->use_internal_phyis false (as default) is it the proper behavior, I thought it is wrong.
Quoted 6 lines
Not sure why it fails.
fdt_node_check_compatiblewill return 0 if the node lists the given compatible string. Andfdt_parent_offsetreturns >= 0 for a valid offset. The logic looks correct:If the PHY node's parent is compatible with "allwinner,sun8i-h3-mdio-internal", set
priv->use_internal_phy= true.
Yes, ie what I thought off. anyway the sunxi/next change has proper logic to traverse the child and set it to true. please make your changes on top, thanks!