Skip to contentSkip to conversation

dt-bindings: arm: fsl: Add devicetree binding for M53 Menlo board.

PATCH Applied Marek Vasut 2 participants 4 messages Apr 12, 2019 – Apr 21, 2019

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v5 1/3 dt-bindings: arm: fsl: Add devicetree binding for M53 Menlo board.

Add devicetree binding for iMX53 SoC based M53 Menlo board.

Cc Rob Herring <[email protected]>
Cc Shawn Guo <[email protected]>
Cc Fabio Estevam <[email protected]>
Cc NXP Linux Team <[email protected]>

To: [email protected]
---
V5: New patch

---
 Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/fsl.yaml +1 -0
index 3c7ad36ebd35..597bff7b6d0e 100644
@@ -67,6 +67,7 @@ properties:
               - fsl,imx53-evk
               - fsl,imx53-qsb
               - fsl,imx53-smd
+              - menlo,m53menlo
           - const: fsl,imx53
 
       - description: i.MX6Q based Boards
Signature · 1 line
2.20.1
#1 lore raw

PATCH v5 2/3 ARM: dts: imx53: Rename M53 SoM touchscreen node

Rename the touchscreen node to match contemporary design.

Cc Shawn Guo <[email protected]>
Cc Fabio Estevam <[email protected]>
Cc NXP Linux Team <[email protected]>

To: [email protected]
---
V4: - New patch
V5: - No change

---
 arch/arm/boot/dts/imx53-m53.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/imx53-m53.dtsi +1 -1
index db2e5bce9b6a..d1770e1d5e50 100644
@@ -52,7 +52,7 @@
 	clock-frequency = <400000>;
 	status = "okay";
 
-	stmpe610@41 {
+	touchscreen@41 {
 		compatible = "st,stmpe610";
 		reg = <0x41>;
 		id = <0>;
Signature · 7 lines
2.20.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#2 lore raw

PATCH v5 3/3 ARM: dts: imx53: Add Menlosystems M53 board

In reply to Marek Vasut

Add device tree for the Menlosystems board based on i.MX53 M53 SoM.

Cc Shawn Guo <[email protected]>
Cc Fabio Estevam <[email protected]>
Cc NXP Linux Team <[email protected]>

To: [email protected]
---
V2: - Rebase on latest next/master
V3: - Add vendor specific compatible for the platform
- Rename ledgrp and touchscreen nodes to follow DT spec
- Update pinmux (LVDS has no pin config, so use default settings)
V4: - Add fsl.yaml entry
- Pull regulator out of simple bus
- Rename touchscreen@ node
- Add reg entry to lvds-channel@0
- Fix touchscreen interrupt polarity
V5: - Separate out the one-line change to fsl.yaml
- Add special comment about the LVDS pin config

---
 arch/arm/boot/dts/Makefile           |   1 +
 arch/arm/boot/dts/imx53-m53menlo.dts | 311 +++++++++++++++++++++++++++
 2 files changed, 312 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx53-m53menlo.dts
arch/arm/boot/dts/Makefile +1 -0
index a969ca820d41..68639c8ddc11 100644
@@ -380,6 +380,7 @@ dtb-$(CONFIG_SOC_IMX53) += \
 	imx53-kp-ddc.dtb \
 	imx53-kp-hsc.dtb \
 	imx53-m53evk.dtb \
+	imx53-m53menlo.dtb \
 	imx53-mba53.dtb \
 	imx53-ppd.dtb \
 	imx53-qsb.dtb \
arch/arm/boot/dts/imx53-m53menlo.dts new file +311 -0

311 lines not on this page · raw message

Signature · 7 lines
2.20.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel