hwmon: (pmbus/ir38064): Add driver for Infineon IR38064 Voltage Regulator
Subsystems (2)
PATCH v3 1/1 hwmon: (pmbus/ir38064): Add driver for Infineon IR38064 Voltage Regulator
From: Maxim Sloyko <[email protected]>
Add the pmbus driver for the Infineon ir38064 voltage regulator.
VOUT_MODE is not supported by the device. The driver fakes linear16 mode with exponent value -8.
The device supports VOUT_PEAK, IOUT_PEAK, and TEMPERATURE_PEAK, however this driver does not enable them.
---
v3:
- Updated commit message to indicate behaviors.
v2:
- Cleaned up weird tabbing behavior in doc.
v1:
- Initial patchset.
--- Documentation/hwmon/ir38064 | 64 +++++++++++++++++++++++++++++++++++ drivers/hwmon/pmbus/Kconfig | 9 +++++ drivers/hwmon/pmbus/Makefile | 1 + drivers/hwmon/pmbus/ir38064.c | 60 ++++++++++++++++++++++++++++++++ 4 files changed, 134 insertions(+) create mode 100644 Documentation/hwmon/ir38064 create mode 100644 drivers/hwmon/pmbus/ir38064.c
Documentation/hwmon/ir38064 new file +64 -0
@@ -0,0 +1,64 @@ +Kernel driver ir38064 +===================== + +Supported chips: + * Infineon IR38064 + Prefix: 'ir38064' + Addresses scanned: - + Datasheet: Publicly available at the Infineon webiste + https://www.infineon.com/dgdl/Infineon-IR38064MTRPBF-DS-v03_07-EN.pdf?fileId=5546d462584d1d4a0158db0d9efb67ca + +Datasheet is not publicly available. + + +Authors: + Maxim Sloyko <[email protected]> + Patrick Venture <[email protected]> + +Description +----------- + +IR38064 is a Single-input Voltage, Synchronous Buck Regulator, DC-DC Converter. + +Usage Notes +----------- + +This driver does not probe for PMBus devices. You will have to instantiate +devices explicitly. + +Sysfs attributes +---------------- + +curr1_label "iout1" +curr1_input Measured output current +curr1_crit Critical maximum current +curr1_crit_alarm Current critical high alarm +curr1_max Maximum current +curr1_max_alarm Current high alarm + +in1_label "vin" +in1_input Measured input voltage +in1_crit Critical maximum input voltage +in1_crit_alarm Input voltage critical high alarm +in1_min Minimum input voltage +in1_min_alarm Input voltage low alarm + +in2_label "vout1" +in2_input Measured output voltage +in2_lcrit Critical minimum output voltage +in2_lcrit_alarm Output voltage critical low alarm +in2_crit Critical maximum output voltage +in2_crit_alarm Output voltage critical high alarm +in2_max Maximum output voltage +in2_max_alarm Output voltage high alarm +in2_min Minimum output voltage +in2_min_alarm Output voltage low alarm + +power1_label "pout1" +power1_input Measured output power + +temp1_input Measured temperature +temp1_crit Critical high temperature +temp1_crit_alarm Chip temperature critical high alarm +temp1_max Maximum temperature +temp1_max_alarm Chip temperature high alarm
drivers/hwmon/pmbus/Kconfig +9 -0
@@ -54,6 +54,15 @@ config SENSORS_IR35221 This driver can also be built as a module. If so, the module will be called ir35521. +config SENSORS_IR38064 + tristate "Infineon IR38064" + help + If you say yes here you get hardware monitoring support for Infineon + IR38064. + + This driver can also be built as a module. If so, the module will + be called ir38064. + config SENSORS_LM25066 tristate "National Semiconductor LM25066 and compatibles" help
drivers/hwmon/pmbus/Makefile +1 -0
@@ -8,6 +8,7 @@ obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o obj-$(CONFIG_SENSORS_IR35221) += ir35221.o +obj-$(CONFIG_SENSORS_IR38064) += ir38064.o obj-$(CONFIG_SENSORS_LM25066) += lm25066.o obj-$(CONFIG_SENSORS_LTC2978) += ltc2978.o obj-$(CONFIG_SENSORS_LTC3815) += ltc3815.o
drivers/hwmon/pmbus/ir38064.c new file +60 -0
60 lines not on this page · raw message
Signature · 1 line
2.21.0.392.gf8f6787159e-goog
Guenter Roeck
maintainerQuoted 10 lines · Patrick Venture
From: Maxim Sloyko <[email protected]>
Add the pmbus driver for the Infineon ir38064 voltage regulator.
VOUT_MODEis not supported by the device. The driver fakes linear16 mode with exponent value -8.The device supports
VOUT_PEAK,IOUT_PEAK, andTEMPERATURE_PEAK, however this driver does not enable them.
I meant to add this into the driver as comment (where people can see it going forward). Never mind, I'll apply the patch and add it myself.
Guenter
Quoted 187 lines
Signed-off-by Maxim Sloyko <[email protected]>Signed-off-by Patrick Venture <[email protected]>---
v3:
- Updated commit message to indicate behaviors.
v2:
- Cleaned up weird tabbing behavior in doc.
v1:
- Initial patchset.--- Documentation/hwmon/ir38064 | 64 +++++++++++++++++++++++++++++++++++ drivers/hwmon/pmbus/Kconfig | 9 +++++ drivers/hwmon/pmbus/Makefile | 1 + drivers/hwmon/pmbus/ir38064.c | 60 ++++++++++++++++++++++++++++++++ 4 files changed, 134 insertions(+)create mode 100644
Documentation/hwmon/ir38064create mode 100644drivers/hwmon/pmbus/ir38064.cDocumentation/hwmon/ir38064 new file +64
-0@@ -0,0 +1,64 @@ +Kernel driver ir38064 +===================== + +Supported chips: + * Infineon IR38064 + Prefix: 'ir38064' + Addresses scanned: - + Datasheet: Publicly available at the Infineon webiste + https://www.infineon.com/dgdl/Infineon-IR38064MTRPBF-DS-v03_07-EN.pdf?fileId=5546d462584d1d4a0158db0d9efb67ca + +Datasheet is not publicly available. + + +Authors: + Maxim Sloyko <[email protected]> + Patrick Venture <[email protected]> + +Description +----------- + +IR38064 is a Single-input Voltage, Synchronous Buck Regulator, DC-DC Converter. + +Usage Notes +----------- + +This driver does not probe for PMBus devices. You will have to instantiate +devices explicitly. + +Sysfs attributes +---------------- + +curr1_label "iout1" +curr1_input Measured output current +curr1_crit Critical maximum current +curr1_crit_alarm Current critical high alarm +curr1_max Maximum current +curr1_max_alarm Current high alarm + +in1_label "vin" +in1_input Measured input voltage +in1_crit Critical maximum input voltage +in1_crit_alarm Input voltage critical high alarm +in1_min Minimum input voltage +in1_min_alarm Input voltage low alarm + +in2_label "vout1" +in2_input Measured output voltage +in2_lcrit Critical minimum output voltage +in2_lcrit_alarm Output voltage critical low alarm +in2_crit Critical maximum output voltage +in2_crit_alarm Output voltage critical high alarm +in2_max Maximum output voltage +in2_max_alarm Output voltage high alarm +in2_min Minimum output voltage +in2_min_alarm Output voltage low alarm + +power1_label "pout1" +power1_input Measured output power + +temp1_input Measured temperature +temp1_crit Critical high temperature +temp1_crit_alarm Chip temperature critical high alarm +temp1_max Maximum temperature +temp1_max_alarm Chip temperature high alarmdrivers/hwmon/pmbus/Kconfig +9
-0@@ -54,6 +54,15 @@ config SENSORS_IR35221 This driver can also be built as a module. If so, the module will be called ir35521. +config SENSORS_IR38064 + tristate "Infineon IR38064" + help + If you say yes here you get hardware monitoring support for Infineon + IR38064. + + This driver can also be built as a module. If so, the module will + be called ir38064. + config SENSORS_LM25066 tristate "National Semiconductor LM25066 and compatibles" helpdrivers/hwmon/pmbus/Makefile +1
-0@@ -8,6 +8,7 @@ obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o obj-$(CONFIG_SENSORS_IR35221) += ir35221.o +obj-$(CONFIG_SENSORS_IR38064) += ir38064.o obj-$(CONFIG_SENSORS_LM25066) += lm25066.o obj-$(CONFIG_SENSORS_LTC2978) += ltc2978.o obj-$(CONFIG_SENSORS_LTC3815) += ltc3815.odrivers/hwmon/pmbus/ir38064.c new file +60
-0@@ -0,0 +1,60 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Hardware monitoring driver for Infineon IR38064 +* +* Copyright (c) 2017 Google Inc +* +*/ + +#include <linux/err.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include "pmbus.h" + +static struct pmbus_driver_info ir38064_info = { + .pages =1 , + .format[PSC_VOLTAGE_IN ] = linear, + .format[PSC_VOLTAGE_OUT ] = direct, + .format[PSC_CURRENT_OUT ] = linear, + .format[PSC_POWER ] = linear, + .format[PSC_TEMPERATURE ] = linear, + .m[PSC_VOLTAGE_OUT ] =256 , + .b[PSC_VOLTAGE_OUT ] =0 , + .R[PSC_VOLTAGE_OUT ] =0 , + .func[0 ] =PMBUS_HAVE_VIN |PMBUS_HAVE_STATUS_INPUT + |PMBUS_HAVE_TEMP |PMBUS_HAVE_STATUS_TEMP + |PMBUS_HAVE_VOUT |PMBUS_HAVE_STATUS_VOUT + |PMBUS_HAVE_IOUT |PMBUS_HAVE_STATUS_IOUT + |PMBUS_HAVE_POUT , +}; + +static int ir38064_probe (struct i2c_client *client, +const struct i2c_device_id *id) +{ +return pmbus_do_probe (client, id, &ir38064_info); +} + +static const struct i2c_device_id ir38064_id[] = { + {"ir38064" ,0 }, + {} +}; + +MODULE_DEVICE_TABLE (i2c, ir38064_id); + +/* This is the driver that will be inserted */ +static struct i2c_driver ir38064_driver = { + .driver = { + .name ="ir38064" , + }, + .probe = ir38064_probe, + .remove = pmbus_do_remove, + .id_table = ir38064_id, +}; + +module_i2c_driver (ir38064_driver); + +MODULE_AUTHOR ("Maxim Sloyko <[email protected]>" ); +MODULE_DESCRIPTION ("PMBus driver for Infineon IR38064" ); +MODULE_LICENSE ("GPL" );
Quoted 9 lines · Guenter Roeck
Quoted 7 lines · Patrick Venture
From: Maxim Sloyko <[email protected]>
Add the pmbus driver for the Infineon ir38064 voltage regulator.
VOUT_MODEis not supported by the device. The driver fakes linear16 mode with exponent value -8.
Quoted 6 lines
Quoted 3 lines
The device supports
VOUT_PEAK,IOUT_PEAK, andTEMPERATURE_PEAK, however this driver does not enable them.I meant to add this into the driver as comment (where people can see it going forward). Never mind, I'll apply the patch and add it myself.
Sorry, I definitely misunderstood your intent. Thanks for handling it.
Quoted 191 lines
Guenter
Quoted 187 lines
Signed-off-by Maxim Sloyko <[email protected]>Signed-off-by Patrick Venture <[email protected]>---
v3:
- Updated commit message to indicate behaviors.
v2:
- Cleaned up weird tabbing behavior in doc.
v1:
- Initial patchset.--- Documentation/hwmon/ir38064 | 64 +++++++++++++++++++++++++++++++++++ drivers/hwmon/pmbus/Kconfig | 9 +++++ drivers/hwmon/pmbus/Makefile | 1 + drivers/hwmon/pmbus/ir38064.c | 60 ++++++++++++++++++++++++++++++++ 4 files changed, 134 insertions(+)create mode 100644
Documentation/hwmon/ir38064create mode 100644drivers/hwmon/pmbus/ir38064.cDocumentation/hwmon/ir38064 new file +64
-0@@ -0,0 +1,64 @@ +Kernel driver ir38064 +===================== + +Supported chips: + * Infineon IR38064 + Prefix: 'ir38064' + Addresses scanned: - + Datasheet: Publicly available at the Infineon webiste + https://www.infineon.com/dgdl/Infineon-IR38064MTRPBF-DS-v03_07-EN.pdf?fileId=5546d462584d1d4a0158db0d9efb67ca + +Datasheet is not publicly available. + + +Authors: + Maxim Sloyko <[email protected]> + Patrick Venture <[email protected]> + +Description +----------- + +IR38064 is a Single-input Voltage, Synchronous Buck Regulator, DC-DC Converter. + +Usage Notes +----------- + +This driver does not probe for PMBus devices. You will have to instantiate +devices explicitly. + +Sysfs attributes +---------------- + +curr1_label "iout1" +curr1_input Measured output current +curr1_crit Critical maximum current +curr1_crit_alarm Current critical high alarm +curr1_max Maximum current +curr1_max_alarm Current high alarm + +in1_label "vin" +in1_input Measured input voltage +in1_crit Critical maximum input voltage +in1_crit_alarm Input voltage critical high alarm +in1_min Minimum input voltage +in1_min_alarm Input voltage low alarm + +in2_label "vout1" +in2_input Measured output voltage +in2_lcrit Critical minimum output voltage +in2_lcrit_alarm Output voltage critical low alarm +in2_crit Critical maximum output voltage +in2_crit_alarm Output voltage critical high alarm +in2_max Maximum output voltage +in2_max_alarm Output voltage high alarm +in2_min Minimum output voltage +in2_min_alarm Output voltage low alarm + +power1_label "pout1" +power1_input Measured output power + +temp1_input Measured temperature +temp1_crit Critical high temperature +temp1_crit_alarm Chip temperature critical high alarm +temp1_max Maximum temperature +temp1_max_alarm Chip temperature high alarmdrivers/hwmon/pmbus/Kconfig +9
-0@@ -54,6 +54,15 @@ config SENSORS_IR35221 This driver can also be built as a module. If so, the module will be called ir35521. +config SENSORS_IR38064 + tristate "Infineon IR38064" + help + If you say yes here you get hardware monitoring support for Infineon + IR38064. + + This driver can also be built as a module. If so, the module will + be called ir38064. + config SENSORS_LM25066 tristate "National Semiconductor LM25066 and compatibles" helpdrivers/hwmon/pmbus/Makefile +1
-0@@ -8,6 +8,7 @@ obj-$(CONFIG_SENSORS_PMBUS) += pmbus.o obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o obj-$(CONFIG_SENSORS_IBM_CFFPS) += ibm-cffps.o obj-$(CONFIG_SENSORS_IR35221) += ir35221.o +obj-$(CONFIG_SENSORS_IR38064) += ir38064.o obj-$(CONFIG_SENSORS_LM25066) += lm25066.o obj-$(CONFIG_SENSORS_LTC2978) += ltc2978.o obj-$(CONFIG_SENSORS_LTC3815) += ltc3815.odrivers/hwmon/pmbus/ir38064.c new file +60
-0@@ -0,0 +1,60 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Hardware monitoring driver for Infineon IR38064 +* +* Copyright (c) 2017 Google Inc +* +*/ + +#include <linux/err.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include "pmbus.h" + +static struct pmbus_driver_info ir38064_info = { + .pages =1 , + .format[PSC_VOLTAGE_IN ] = linear, + .format[PSC_VOLTAGE_OUT ] = direct, + .format[PSC_CURRENT_OUT ] = linear, + .format[PSC_POWER ] = linear, + .format[PSC_TEMPERATURE ] = linear, + .m[PSC_VOLTAGE_OUT ] =256 , + .b[PSC_VOLTAGE_OUT ] =0 , + .R[PSC_VOLTAGE_OUT ] =0 , + .func[0 ] =PMBUS_HAVE_VIN |PMBUS_HAVE_STATUS_INPUT + |PMBUS_HAVE_TEMP |PMBUS_HAVE_STATUS_TEMP + |PMBUS_HAVE_VOUT |PMBUS_HAVE_STATUS_VOUT + |PMBUS_HAVE_IOUT |PMBUS_HAVE_STATUS_IOUT + |PMBUS_HAVE_POUT , +}; + +static int ir38064_probe (struct i2c_client *client, +const struct i2c_device_id *id) +{ +return pmbus_do_probe (client, id, &ir38064_info); +} + +static const struct i2c_device_id ir38064_id[] = { + {"ir38064" ,0 }, + {} +}; + +MODULE_DEVICE_TABLE (i2c, ir38064_id); + +/* This is the driver that will be inserted */ +static struct i2c_driver ir38064_driver = { + .driver = { + .name ="ir38064" , + }, + .probe = ir38064_probe, + .remove = pmbus_do_remove, + .id_table = ir38064_id, +}; + +module_i2c_driver (ir38064_driver); + +MODULE_AUTHOR ("Maxim Sloyko <[email protected]>" ); +MODULE_DESCRIPTION ("PMBus driver for Infineon IR38064" ); +MODULE_LICENSE ("GPL" );