ARM: imx6: DHCOM i.MX6 PDK: use Kconfig for inclusion of DDR calibration
PATCH v2 1/2 ARM: imx6: DHCOM i.MX6 PDK: use Kconfig for inclusion of DDR calibration
From: Ludwig Zenz <[email protected]>
The four x16 DDR3 are wired in T-topology. From NXP AN4467:
'Although not required, T-Topologies may also benefit from performing Write Leveling as there are package delays on both the processor and DDR devices that can be de-skewed by performing Write Leveling. Therefore, Freescale recommends determining Write Leveling calibration parameters for all boards, regardless of topology used.'
That is why write level calibration is also done.
--- board/dhelectronics/dh_imx6/dh_imx6_spl.c | 32 +++++++++++++++++++++++++------ 1 file changed, 26 insertions(+), 6 deletions(-)
board/dhelectronics/dh_imx6/dh_imx6_spl.c +26 -6
@@ -482,6 +482,29 @@ static void setup_iomux_usb(void)SETUP_IOMUX_PADS (usb_pads); } +/* Perform DDR DRAM calibration */ +static int spl_dram_perform_cal (struct mx6_ddr_sysinfo const *sysinfo) +{ +int ret =0 ; + +#ifdef CONFIG_MX6_DDRCAL +udelay (100 ); + ret =mmdc_do_write_level_calibration (sysinfo); +if (ret) { +printf ("DDR3: Write level calibration error [%d]\n" , ret); +return ret; + } + + ret =mmdc_do_dqs_calibration (sysinfo); +if (ret) { +printf ("DDR3: DQS calibration error [%d]\n" , ret); +return ret; + } +#endif /* CONFIG_MX6_DDRCAL */ + +return ret; +} +/* DRAM */ static void dhcom_spl_dram_init (void )
@@ -509,8 +532,7 @@ static void dhcom_spl_dram_init(void) }/* Perform DDR DRAM calibration */ -udelay (100 ); -mmdc_do_dqs_calibration (&dhcom_ddr_64bit); +spl_dram_perform_cal (&dhcom_ddr_64bit); }else if (is_cpu_type (MXC_CPU_MX6DL )) { mx6sdl_dram_iocfg(64, &dhcom6sdl_ddr_ioregs,
@@ -528,8 +550,7 @@ static void dhcom_spl_dram_init(void) }/* Perform DDR DRAM calibration */ -udelay (100 ); -mmdc_do_dqs_calibration (&dhcom_ddr_64bit); +spl_dram_perform_cal (&dhcom_ddr_64bit); }else if (is_cpu_type (MXC_CPU_MX6SOLO )) { mx6sdl_dram_iocfg(32, &dhcom6sdl_ddr_ioregs,
@@ -552,8 +573,7 @@ static void dhcom_spl_dram_init(void) }/* Perform DDR DRAM calibration */ -udelay (100 ); -mmdc_do_dqs_calibration (&dhcom_ddr_32bit); +spl_dram_perform_cal (&dhcom_ddr_32bit); } }
Signature · 1 line
2.11.0
PATCH v2 1/2 ARM: imx6: DHCOM i.MX6 PDK: use Kconfig for inclusion of DDR calibration
Quoted 9 lines
From: Ludwig Zenz <[email protected]>
The four x16 DDR3 are wired in T-topology. From NXP AN4467:
'Although not required, T-Topologies may also benefit from performing Write Leveling as there are package delays on both the processor and DDR devices that can be de-skewed by performing Write Leveling. Therefore, Freescale recommends determining Write Leveling calibration parameters for all boards, regardless of topology used.'
That is why write level calibration is also done.Signed-off-by Ludwig Zenz <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================