Skip to contentSkip to conversation

hwmon: (pmbus/isl68137): Add driver for Intersil ISL68137 PWM Controller

PATCH Applied Patrick Venture 2 participants 3 messages Apr 15, 2019

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v5 2/2 hwmon: (pmbus/isl68137): Add driver for Intersil ISL68137 PWM Controller

From: Maxim Sloyko <[email protected]>

Intersil ISL68137 is a digital output 7-phase configurable PWM controller with an AVSBus interface.

---
v5:
Drop extra parens
Drop extra parameter check
v4:
Use kstrtobool
Cleanup parens
Use rc instead of temporary int
Delete unnecessary coment
Add remove to driver structure
v3:
Added missing driver documentation
Cleaned up goto statements.
Add missing error check on pmbus_read_word_data
Transitioned to use SENSOR_DEVICE_ATTR_RW
Renamed enabled attribute to enable
Set up an attribute_group for the enable attribute and added to pmbus_info Removed the boilerplate driver remove method
v2:
Fixed bad header ordering.
v1:
Original new patchset with fixes from Rob Lippert.

---
 Documentation/hwmon/isl68137   |  72 ++++++++++++++
 drivers/hwmon/pmbus/Kconfig    |   9 ++
 drivers/hwmon/pmbus/Makefile   |   1 +
 drivers/hwmon/pmbus/isl68137.c | 172 +++++++++++++++++++++++++++++++++
 4 files changed, 254 insertions(+)
 create mode 100644 Documentation/hwmon/isl68137
 create mode 100644 drivers/hwmon/pmbus/isl68137.c
Documentation/hwmon/isl68137 new file +72 -0
new file mode 100644
index 0000000000000..92e5c5fc5b777
@@ -0,0 +1,72 @@
+Kernel driver isl68137
+======================
+
+Supported chips:
+  * Intersil ISL68137
+    Prefix: 'isl68137'
+    Addresses scanned: -
+    Datasheet: Publicly available at the Intersil website
+      https://www.intersil.com/content/dam/Intersil/documents/isl6/isl68137.pdf
+
+Authors:
+        Maxim Sloyko <[email protected]>
+        Robert Lippert <[email protected]>
+        Patrick Venture <[email protected]>
+
+Description
+-----------
+
+Intersil ISL68137 is a digital output 7-phase configurable PWM
+controller with an AVSBus interface.
+
+Usage Notes
+-----------
+
+This driver does not probe for PMBus devices. You will have to instantiate
+devices explicitly.
+
+The ISL68137 AVS operation mode must be enabled/disabled at runtime.
+
+Beyond the normal sysfs pmbus attributes, the driver exposes a control attribute.
+
+Additional Sysfs attributes
+---------------------------
+
+avs(0|1)_enable		Controls the AVS state of each rail.
+
+curr1_label		"iin"
+curr1_input		Measured input current
+curr1_crit		Critical maximum current
+curr1_crit_alarm	Current critical high alarm
+
+curr[2-3]_label		"iout[1-2]"
+curr[2-3]_input		Measured output current
+curr[2-3]_crit		Critical maximum current
+curr[2-3]_crit_alarm	Current critical high alarm
+
+in1_label		"vin"
+in1_input		Measured input voltage
+in1_lcrit		Critical minimum input voltage
+in1_lcrit_alarm		Input voltage critical low alarm
+in1_crit		Critical maximum input voltage
+in1_crit_alarm		Input voltage critical high alarm
+
+in[2-3]_label		"vout[1-2]"
+in[2-3]_input		Measured output voltage
+in[2-3]_lcrit		Critical minimum output voltage
+in[2-3]_lcrit_alarm	Output voltage critical low alarm
+in[2-3]_crit		Critical maximum output voltage
+in[2-3]_crit_alarm	Output voltage critical high alarm
+
+power1_label		"pin"
+power1_input		Measured input power
+power1_alarm		Input power high alarm
+
+power[2-3]_label	"pout[1-2]"
+power[2-3]_input	Measured output power
+
+temp[1-3]_input		Measured temperature
+temp[1-3]_crit		Critical high temperature
+temp[1-3]_crit_alarm	Chip temperature critical high alarm
+temp[1-3]_max		Maximum temperature
+temp[1-3]_max_alarm	Chip temperature high alarm
drivers/hwmon/pmbus/Kconfig +9 -0
index de87abab990e5..7edab7e30eaf9 100644
@@ -63,6 +63,15 @@ config SENSORS_IR38064
 	  This driver can also be built as a module. If so, the module will
 	  be called ir38064.
 
+config SENSORS_ISL68137
+	tristate "Intersil ISL68137"
+	help
+	  If you say yes here you get hardware monitoring support for Intersil
+	  ISL68137.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called isl68137.
+
 config SENSORS_LM25066
 	tristate "National Semiconductor LM25066 and compatibles"
 	help
drivers/hwmon/pmbus/Makefile +1 -0
index 7d1fa6b3c8c93..2219b93003167 100644
@@ -9,6 +9,7 @@ obj-$(CONFIG_SENSORS_ADM1275)	+= adm1275.o
 obj-$(CONFIG_SENSORS_IBM_CFFPS)	+= ibm-cffps.o
 obj-$(CONFIG_SENSORS_IR35221)	+= ir35221.o
 obj-$(CONFIG_SENSORS_IR38064)	+= ir38064.o
+obj-$(CONFIG_SENSORS_ISL68137)	+= isl68137.o
 obj-$(CONFIG_SENSORS_LM25066)	+= lm25066.o
 obj-$(CONFIG_SENSORS_LTC2978)	+= ltc2978.o
 obj-$(CONFIG_SENSORS_LTC3815)	+= ltc3815.o
drivers/hwmon/pmbus/isl68137.c new file +169 -0

169 lines not on this page · raw message

Signature · 1 line
2.21.0.392.gf8f6787159e-goog
maintainer
#1 lore raw
Quoted 8 lines · Patrick Venture

From: Maxim Sloyko <[email protected]>

Intersil ISL68137 is a digital output 7-phase configurable PWM controller with an AVSBus interface.

For some reason I can not apply this patch - git reports that it is corrupt. Can you check what happened ? I can't figure it out.

Another comment below - makes me wonder - was that a test ?

Since we are getting close, I applied the other patch. No need to resend.

Thanks,
Guenter

Quoted 177 lines

---
v5:
Drop extra parens
Drop extra parameter check
v4:
Use kstrtobool
Cleanup parens
Use rc instead of temporary int
Delete unnecessary coment
Add remove to driver structure
v3:
Added missing driver documentation
Cleaned up goto statements.
Add missing error check on pmbus_read_word_data
Transitioned to use SENSOR_DEVICE_ATTR_RW
Renamed enabled attribute to enable
Set up an attribute_group for the enable attribute and added to pmbus_info Removed the boilerplate driver remove method
v2:
Fixed bad header ordering.
v1:
Original new patchset with fixes from Rob Lippert.

---
 Documentation/hwmon/isl68137   |  72 ++++++++++++++
 drivers/hwmon/pmbus/Kconfig    |   9 ++
 drivers/hwmon/pmbus/Makefile   |   1 +
 drivers/hwmon/pmbus/isl68137.c | 172 +++++++++++++++++++++++++++++++++
 4 files changed, 254 insertions(+)
 create mode 100644 Documentation/hwmon/isl68137
 create mode 100644 drivers/hwmon/pmbus/isl68137.c
Documentation/hwmon/isl68137 new file +72 -0
new file mode 100644
index 0000000000000..92e5c5fc5b777
@@ -0,0 +1,72 @@
+Kernel driver isl68137
+======================
+
+Supported chips:
+  * Intersil ISL68137
+    Prefix: 'isl68137'
+    Addresses scanned: -
+    Datasheet: Publicly available at the Intersil website
+      https://www.intersil.com/content/dam/Intersil/documents/isl6/isl68137.pdf
+
+Authors:
+        Maxim Sloyko <[email protected]>
+        Robert Lippert <[email protected]>
+        Patrick Venture <[email protected]>
+
+Description
+-----------
+
+Intersil ISL68137 is a digital output 7-phase configurable PWM
+controller with an AVSBus interface.
+
+Usage Notes
+-----------
+
+This driver does not probe for PMBus devices. You will have to instantiate
+devices explicitly.
+
+The ISL68137 AVS operation mode must be enabled/disabled at runtime.
+
+Beyond the normal sysfs pmbus attributes, the driver exposes a control attribute.
+
+Additional Sysfs attributes
+---------------------------
+
+avs(0|1)_enable		Controls the AVS state of each rail.
+
+curr1_label		"iin"
+curr1_input		Measured input current
+curr1_crit		Critical maximum current
+curr1_crit_alarm	Current critical high alarm
+
+curr[2-3]_label		"iout[1-2]"
+curr[2-3]_input		Measured output current
+curr[2-3]_crit		Critical maximum current
+curr[2-3]_crit_alarm	Current critical high alarm
+
+in1_label		"vin"
+in1_input		Measured input voltage
+in1_lcrit		Critical minimum input voltage
+in1_lcrit_alarm		Input voltage critical low alarm
+in1_crit		Critical maximum input voltage
+in1_crit_alarm		Input voltage critical high alarm
+
+in[2-3]_label		"vout[1-2]"
+in[2-3]_input		Measured output voltage
+in[2-3]_lcrit		Critical minimum output voltage
+in[2-3]_lcrit_alarm	Output voltage critical low alarm
+in[2-3]_crit		Critical maximum output voltage
+in[2-3]_crit_alarm	Output voltage critical high alarm
+
+power1_label		"pin"
+power1_input		Measured input power
+power1_alarm		Input power high alarm
+
+power[2-3]_label	"pout[1-2]"
+power[2-3]_input	Measured output power
+
+temp[1-3]_input		Measured temperature
+temp[1-3]_crit		Critical high temperature
+temp[1-3]_crit_alarm	Chip temperature critical high alarm
+temp[1-3]_max		Maximum temperature
+temp[1-3]_max_alarm	Chip temperature high alarm
drivers/hwmon/pmbus/Kconfig +9 -0
index de87abab990e5..7edab7e30eaf9 100644
@@ -63,6 +63,15 @@ config SENSORS_IR38064
 	  This driver can also be built as a module. If so, the module will
 	  be called ir38064.
 
+config SENSORS_ISL68137
+	tristate "Intersil ISL68137"
+	help
+	  If you say yes here you get hardware monitoring support for Intersil
+	  ISL68137.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called isl68137.
+
 config SENSORS_LM25066
 	tristate "National Semiconductor LM25066 and compatibles"
 	help
drivers/hwmon/pmbus/Makefile +1 -0
index 7d1fa6b3c8c93..2219b93003167 100644
@@ -9,6 +9,7 @@ obj-$(CONFIG_SENSORS_ADM1275)	+= adm1275.o
 obj-$(CONFIG_SENSORS_IBM_CFFPS)	+= ibm-cffps.o
 obj-$(CONFIG_SENSORS_IR35221)	+= ir35221.o
 obj-$(CONFIG_SENSORS_IR38064)	+= ir38064.o
+obj-$(CONFIG_SENSORS_ISL68137)	+= isl68137.o
 obj-$(CONFIG_SENSORS_LM25066)	+= lm25066.o
 obj-$(CONFIG_SENSORS_LTC2978)	+= ltc2978.o
 obj-$(CONFIG_SENSORS_LTC3815)	+= ltc3815.o
drivers/hwmon/pmbus/isl68137.c new file +30 -0
new file mode 100644
index 0000000000000..4140c52d6f124
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Hardware monitoring driver for Intersil ISL68137
+ *
+ * Copyright (c) 2017 Google Inc
+ *
+ */
+
+#include <linux/err.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/string.h>
+#include <linux/sysfs.h>
+#include "pmbus.h"
+
+#define ISL68137_VOUT_AVS	0x30
+
+static ssize_t isl68137_avs_enable_show_page(struct i2c_client *client,
+					     int page,
+					     char *buf)
+{
+	int val = pmbus_read_byte_data(client, page, PMBUS_OPERATION);
+
+	return sprintf(buf, "%d\n",
+		       (val & ISL68137_VOUT_AVS) == ISL68137_VOUT_AVS ? 1 : 0);
+}
+

drivers/hwmon/pmbus/isl68137.c line 40

Quoted 10 lines
drivers/hwmon/pmbus/isl68137.c new file +10 -0
+static ssize_t isl68137_avs_enable_store_page(struct i2c_client *client,
+					      int page,
+					      const char *buf, size_t count)
+{
+	int rc, op_val;
+	bool result;
+
+	rc = kstrtobool(buf, &result);
+	if (!rc)
+		return -EINVAL;
	if (rc)
		return rc;
Quoted 132 lines
drivers/hwmon/pmbus/isl68137.c new file +129 -0
+
+	op_val = result ? ISL68137_VOUT_AVS : 0;
+
+	/*
+	 * Writes to VOUT setpoint over AVSBus will persist after the VRM is
+	 * switched to PMBus control. Switching back to AVSBus control
+	 * restores this persisted setpoint rather than re-initializing to
+	 * PMBus VOUT_COMMAND. Writing VOUT_COMMAND first over PMBus before
+	 * enabling AVS control is the workaround.
+	 */
+	if (op_val == ISL68137_VOUT_AVS) {
+		rc = pmbus_read_word_data(client, page, PMBUS_VOUT_COMMAND);
+		if (rc < 0)
+			return rc;
+
+		rc = pmbus_write_word_data(client, page, PMBUS_VOUT_COMMAND,
+					   rc);
+		if (rc < 0)
+			return rc;
+	}
+
+	rc = pmbus_update_byte_data(client, page, PMBUS_OPERATION,
+				    ISL68137_VOUT_AVS, op_val);
+
+	return (rc < 0) ? rc : count;
+}
+
+static ssize_t isl68137_avs_enable_show(struct device *dev,
+					struct device_attribute *devattr,
+					char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev->parent);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+
+	return isl68137_avs_enable_show_page(client, attr->index, buf);
+}
+
+static ssize_t isl68137_avs_enable_store(struct device *dev,
+				struct device_attribute *devattr,
+				const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev->parent);
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+
+	return isl68137_avs_enable_store_page(client, attr->index, buf, count);
+}
+
+static SENSOR_DEVICE_ATTR_RW(avs0_enable, isl68137_avs_enable, 0);
+static SENSOR_DEVICE_ATTR_RW(avs1_enable, isl68137_avs_enable, 1);
+
+static struct attribute *enable_attrs[] = {
+	&sensor_dev_attr_avs0_enable.dev_attr.attr,
+	&sensor_dev_attr_avs1_enable.dev_attr.attr,
+	NULL,
+};
+
+static const struct attribute_group enable_group = {
+	.attrs = enable_attrs,
+};
+
+static const struct attribute_group *attribute_groups[] = {
+	&enable_group,
+	NULL,
+};
+
+static struct pmbus_driver_info isl68137_info = {
+	.pages = 2,
+	.format[PSC_VOLTAGE_IN] = direct,
+	.format[PSC_VOLTAGE_OUT] = direct,
+	.format[PSC_CURRENT_IN] = direct,
+	.format[PSC_CURRENT_OUT] = direct,
+	.format[PSC_POWER] = direct,
+	.format[PSC_TEMPERATURE] = direct,
+	.m[PSC_VOLTAGE_IN] = 1,
+	.b[PSC_VOLTAGE_IN] = 0,
+	.R[PSC_VOLTAGE_IN] = 3,
+	.m[PSC_VOLTAGE_OUT] = 1,
+	.b[PSC_VOLTAGE_OUT] = 0,
+	.R[PSC_VOLTAGE_OUT] = 3,
+	.m[PSC_CURRENT_IN] = 1,
+	.b[PSC_CURRENT_IN] = 0,
+	.R[PSC_CURRENT_IN] = 2,
+	.m[PSC_CURRENT_OUT] = 1,
+	.b[PSC_CURRENT_OUT] = 0,
+	.R[PSC_CURRENT_OUT] = 1,
+	.m[PSC_POWER] = 1,
+	.b[PSC_POWER] = 0,
+	.R[PSC_POWER] = 0,
+	.m[PSC_TEMPERATURE] = 1,
+	.b[PSC_TEMPERATURE] = 0,
+	.R[PSC_TEMPERATURE] = 0,
+	.func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_IIN | PMBUS_HAVE_PIN
+	    | PMBUS_HAVE_STATUS_INPUT | PMBUS_HAVE_TEMP | PMBUS_HAVE_TEMP2
+	    | PMBUS_HAVE_TEMP3 | PMBUS_HAVE_STATUS_TEMP
+	    | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT
+	    | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_POUT,
+	.func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT
+	    | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_POUT,
+	.groups = attribute_groups,
+};
+
+static int isl68137_probe(struct i2c_client *client,
+			  const struct i2c_device_id *id)
+{
+	return pmbus_do_probe(client, id, &isl68137_info);
+}
+
+static const struct i2c_device_id isl68137_id[] = {
+	{"isl68137", 0},
+	{}
+};
+
+MODULE_DEVICE_TABLE(i2c, isl68137_id);
+
+/* This is the driver that will be inserted */
+static struct i2c_driver isl68137_driver = {
+	.driver = {
+		   .name = "isl68137",
+		   },
+	.probe = isl68137_probe,
+	.remove = pmbus_do_remove,
+	.id_table = isl68137_id,
+};
+
+module_i2c_driver(isl68137_driver);
+
+MODULE_AUTHOR("Maxim Sloyko <[email protected]>");
+MODULE_DESCRIPTION("PMBus driver for Intersil ISL68137");
+MODULE_LICENSE("GPL");
Signature · 1 line
2.21.0.392.gf8f6787159e-goog
#2 lore raw
Quoted 7 lines · Guenter Roeck
Quoted 5 lines · Patrick Venture

From: Maxim Sloyko <[email protected]>

Intersil ISL68137 is a digital output 7-phase configurable PWM controller with an AVSBus interface.

Quoted 6 lines
Quoted 3 lines

For some reason I can not apply this patch - git reports that it is corrupt. Can you check what happened ? I can't figure it out.

Weird, I'll update the repo and try again once the other patch goes publicly applied (versus email list).

Quoted 190 lines

Another comment below - makes me wonder - was that a test ?

Since we are getting close, I applied the other patch. No need to resend.

Thanks,
Guenter

Quoted 182 lines

---
v5:
Drop extra parens
Drop extra parameter check
v4:
Use kstrtobool
Cleanup parens
Use rc instead of temporary int
Delete unnecessary coment
Add remove to driver structure
v3:
Added missing driver documentation
Cleaned up goto statements.
Add missing error check on pmbus_read_word_data
Transitioned to use SENSOR_DEVICE_ATTR_RW
Renamed enabled attribute to enable
Set up an attribute_group for the enable attribute and added to pmbus_info Removed the boilerplate driver remove method
v2:
Fixed bad header ordering.
v1:
Original new patchset with fixes from Rob Lippert.

---
 Documentation/hwmon/isl68137   |  72 ++++++++++++++
 drivers/hwmon/pmbus/Kconfig    |   9 ++
 drivers/hwmon/pmbus/Makefile   |   1 +
 drivers/hwmon/pmbus/isl68137.c | 172 +++++++++++++++++++++++++++++++++
 4 files changed, 254 insertions(+)
 create mode 100644 Documentation/hwmon/isl68137
 create mode 100644 drivers/hwmon/pmbus/isl68137.c
Documentation/hwmon/isl68137 new file +72 -0
new file mode 100644
index 0000000000000..92e5c5fc5b777
@@ -0,0 +1,72 @@
+Kernel driver isl68137
+======================
+
+Supported chips:
+  * Intersil ISL68137
+    Prefix: 'isl68137'
+    Addresses scanned: -
+    Datasheet: Publicly available at the Intersil website
+      https://www.intersil.com/content/dam/Intersil/documents/isl6/isl68137.pdf
+
+Authors:
+        Maxim Sloyko <[email protected]>
+        Robert Lippert <[email protected]>
+        Patrick Venture <[email protected]>
+
+Description
+-----------
+
+Intersil ISL68137 is a digital output 7-phase configurable PWM
+controller with an AVSBus interface.
+
+Usage Notes
+-----------
+
+This driver does not probe for PMBus devices. You will have to instantiate
+devices explicitly.
+
+The ISL68137 AVS operation mode must be enabled/disabled at runtime.
+
+Beyond the normal sysfs pmbus attributes, the driver exposes a control attribute.
+
+Additional Sysfs attributes
+---------------------------
+
+avs(0|1)_enable              Controls the AVS state of each rail.
+
+curr1_label          "iin"
+curr1_input          Measured input current
+curr1_crit           Critical maximum current
+curr1_crit_alarm     Current critical high alarm
+
+curr[2-3]_label              "iout[1-2]"
+curr[2-3]_input              Measured output current
+curr[2-3]_crit               Critical maximum current
+curr[2-3]_crit_alarm Current critical high alarm
+
+in1_label            "vin"
+in1_input            Measured input voltage
+in1_lcrit            Critical minimum input voltage
+in1_lcrit_alarm              Input voltage critical low alarm
+in1_crit             Critical maximum input voltage
+in1_crit_alarm               Input voltage critical high alarm
+
+in[2-3]_label                "vout[1-2]"
+in[2-3]_input                Measured output voltage
+in[2-3]_lcrit                Critical minimum output voltage
+in[2-3]_lcrit_alarm  Output voltage critical low alarm
+in[2-3]_crit         Critical maximum output voltage
+in[2-3]_crit_alarm   Output voltage critical high alarm
+
+power1_label         "pin"
+power1_input         Measured input power
+power1_alarm         Input power high alarm
+
+power[2-3]_label     "pout[1-2]"
+power[2-3]_input     Measured output power
+
+temp[1-3]_input              Measured temperature
+temp[1-3]_crit               Critical high temperature
+temp[1-3]_crit_alarm Chip temperature critical high alarm
+temp[1-3]_max                Maximum temperature
+temp[1-3]_max_alarm  Chip temperature high alarm
drivers/hwmon/pmbus/Kconfig +9 -0
index de87abab990e5..7edab7e30eaf9 100644
@@ -63,6 +63,15 @@ config SENSORS_IR38064
        This driver can also be built as a module. If so, the module will
        be called ir38064.
 
+config SENSORS_ISL68137
+     tristate "Intersil ISL68137"
+     help
+       If you say yes here you get hardware monitoring support for Intersil
+       ISL68137.
+
+       This driver can also be built as a module. If so, the module will
+       be called isl68137.
+
 config SENSORS_LM25066
      tristate "National Semiconductor LM25066 and compatibles"
      help
drivers/hwmon/pmbus/Makefile +1 -0
index 7d1fa6b3c8c93..2219b93003167 100644
@@ -9,6 +9,7 @@ obj-$(CONFIG_SENSORS_ADM1275) += adm1275.o
 obj-$(CONFIG_SENSORS_IBM_CFFPS)      += ibm-cffps.o
 obj-$(CONFIG_SENSORS_IR35221)        += ir35221.o
 obj-$(CONFIG_SENSORS_IR38064)        += ir38064.o
+obj-$(CONFIG_SENSORS_ISL68137)       += isl68137.o
 obj-$(CONFIG_SENSORS_LM25066)        += lm25066.o
 obj-$(CONFIG_SENSORS_LTC2978)        += ltc2978.o
 obj-$(CONFIG_SENSORS_LTC3815)        += ltc3815.o
drivers/hwmon/pmbus/isl68137.c new file +35 -0
new file mode 100644
index 0000000000000..4140c52d6f124
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Hardware monitoring driver for Intersil ISL68137
+ *
+ * Copyright (c) 2017 Google Inc
+ *
+ */
+
+#include <linux/err.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/string.h>
+#include <linux/sysfs.h>
+#include "pmbus.h"
+
+#define ISL68137_VOUT_AVS    0x30
+
+static ssize_t isl68137_avs_enable_show_page(struct i2c_client *client,
+                                          int page,
+                                          char *buf)
+{
+     int val = pmbus_read_byte_data(client, page, PMBUS_OPERATION);
+
+     return sprintf(buf, "%d\n",
+                    (val & ISL68137_VOUT_AVS) == ISL68137_VOUT_AVS ? 1 : 0);
+}
+
+static ssize_t isl68137_avs_enable_store_page(struct i2c_client *client,
+                                           int page,
+                                           const char *buf, size_t count)
+{
+     int rc, op_val;
Quoted 8 lines

drivers/hwmon/pmbus/isl68137.c line 40

Quoted 5 lines
drivers/hwmon/pmbus/isl68137.c new file +5 -0
+     bool result;
+
+     rc = kstrtobool(buf, &result);
+     if (!rc)
+             return -EINVAL;
        if (rc)
                return rc;

That was a normal patchset fatigue mistake, not a test. The pattern of "if (rc) return rc" is common enough, is there a macro I should be using?

Quoted 133 lines
Quoted 133 lines
drivers/hwmon/pmbus/isl68137.c new file +129 -1
+
+     op_val = result ? ISL68137_VOUT_AVS : 0;
+
+     /*
+      * Writes to VOUT setpoint over AVSBus will persist after the VRM is
+      * switched to PMBus control. Switching back to AVSBus control
+      * restores this persisted setpoint rather than re-initializing to
+      * PMBus VOUT_COMMAND. Writing VOUT_COMMAND first over PMBus before
+      * enabling AVS control is the workaround.
+      */
+     if (op_val == ISL68137_VOUT_AVS) {
+             rc = pmbus_read_word_data(client, page, PMBUS_VOUT_COMMAND);
+             if (rc < 0)
+                     return rc;
+
+             rc = pmbus_write_word_data(client, page, PMBUS_VOUT_COMMAND,
+                                        rc);
+             if (rc < 0)
+                     return rc;
+     }
+
+     rc = pmbus_update_byte_data(client, page, PMBUS_OPERATION,
+                                 ISL68137_VOUT_AVS, op_val);
+
+     return (rc < 0) ? rc : count;
+}
+
+static ssize_t isl68137_avs_enable_show(struct device *dev,
+                                     struct device_attribute *devattr,
+                                     char *buf)
+{
+     struct i2c_client *client = to_i2c_client(dev->parent);
+     struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+
+     return isl68137_avs_enable_show_page(client, attr->index, buf);
+}
+
+static ssize_t isl68137_avs_enable_store(struct device *dev,
+                             struct device_attribute *devattr,
+                             const char *buf, size_t count)
+{
+     struct i2c_client *client = to_i2c_client(dev->parent);
+     struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+
+     return isl68137_avs_enable_store_page(client, attr->index, buf, count);
+}
+
+static SENSOR_DEVICE_ATTR_RW(avs0_enable, isl68137_avs_enable, 0);
+static SENSOR_DEVICE_ATTR_RW(avs1_enable, isl68137_avs_enable, 1);
+
+static struct attribute *enable_attrs[] = {
+     &sensor_dev_attr_avs0_enable.dev_attr.attr,
+     &sensor_dev_attr_avs1_enable.dev_attr.attr,
+     NULL,
+};
+
+static const struct attribute_group enable_group = {
+     .attrs = enable_attrs,
+};
+
+static const struct attribute_group *attribute_groups[] = {
+     &enable_group,
+     NULL,
+};
+
+static struct pmbus_driver_info isl68137_info = {
+     .pages = 2,
+     .format[PSC_VOLTAGE_IN] = direct,
+     .format[PSC_VOLTAGE_OUT] = direct,
+     .format[PSC_CURRENT_IN] = direct,
+     .format[PSC_CURRENT_OUT] = direct,
+     .format[PSC_POWER] = direct,
+     .format[PSC_TEMPERATURE] = direct,
+     .m[PSC_VOLTAGE_IN] = 1,
+     .b[PSC_VOLTAGE_IN] = 0,
+     .R[PSC_VOLTAGE_IN] = 3,
+     .m[PSC_VOLTAGE_OUT] = 1,
+     .b[PSC_VOLTAGE_OUT] = 0,
+     .R[PSC_VOLTAGE_OUT] = 3,
+     .m[PSC_CURRENT_IN] = 1,
+     .b[PSC_CURRENT_IN] = 0,
+     .R[PSC_CURRENT_IN] = 2,
+     .m[PSC_CURRENT_OUT] = 1,
+     .b[PSC_CURRENT_OUT] = 0,
+     .R[PSC_CURRENT_OUT] = 1,
+     .m[PSC_POWER] = 1,
+     .b[PSC_POWER] = 0,
+     .R[PSC_POWER] = 0,
+     .m[PSC_TEMPERATURE] = 1,
+     .b[PSC_TEMPERATURE] = 0,
+     .R[PSC_TEMPERATURE] = 0,
+     .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_IIN | PMBUS_HAVE_PIN
+         | PMBUS_HAVE_STATUS_INPUT | PMBUS_HAVE_TEMP | PMBUS_HAVE_TEMP2
+         | PMBUS_HAVE_TEMP3 | PMBUS_HAVE_STATUS_TEMP
+         | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT
+         | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_POUT,
+     .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT
+         | PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_POUT,
+     .groups = attribute_groups,
+};
+
+static int isl68137_probe(struct i2c_client *client,
+                       const struct i2c_device_id *id)
+{
+     return pmbus_do_probe(client, id, &isl68137_info);
+}
+
+static const struct i2c_device_id isl68137_id[] = {
+     {"isl68137", 0},
+     {}
+};
+
+MODULE_DEVICE_TABLE(i2c, isl68137_id);
+
+/* This is the driver that will be inserted */
+static struct i2c_driver isl68137_driver = {
+     .driver = {
+                .name = "isl68137",
+                },
+     .probe = isl68137_probe,
+     .remove = pmbus_do_remove,
+     .id_table = isl68137_id,
+};
+
+module_i2c_driver(isl68137_driver);
+
+MODULE_AUTHOR("Maxim Sloyko <[email protected]>");
+MODULE_DESCRIPTION("PMBus driver for Intersil ISL68137");
+MODULE_LICENSE("GPL");
--

2.21.0.392.gf8f6787159e-goog