usb: dwc2: Another attempt handling rk3288's remote wake quirk
Subsystems (4)
v2 cover usb: dwc2: Another attempt handling rk3288's remote wake quirk
This is another attempt to upstream the code to unwedge the rk3288's "host" USB port when it sees a remote wakeup. Previously I attempted this [1] and it appears that Randy Li made some attempts too [2] which resulted in at least the PHY bindings for the USB PHY landing as well as the USB PHY support. Nice!
Hopefully this addresses previous comments and could land this time?
[1] https://lkml.kernel.org/r/[email protected]
[2] https://lkml.kernel.org/r/[email protected]
Changes in v2:
- Cancel the work when dwc2 is freed (Matthias).
Douglas Anderson (4):
dt-bindings: usb: dwc2: Document quirk to reset PHY upon wakeup
usb: dwc2: optionally assert phy reset when waking up
ARM: dts: rockchip: Hook resets up to USB PHYs on rk3288.
ARM: dts: rockchip: Add quirk for resetting rk3288's dwc2 host on
wakeup
Documentation/devicetree/bindings/usb/dwc2.txt | 2 ++ arch/arm/boot/dts/rk3288.dtsi | 7 +++++++ drivers/usb/dwc2/core.h | 5 +++++ drivers/usb/dwc2/core_intr.c | 12 ++++++++++++ drivers/usb/dwc2/hcd.c | 18 +++++++++++++++--- drivers/usb/dwc2/platform.c | 9 +++++++++ 6 files changed, 50 insertions(+), 3 deletions(-)
Signature · 1 line
2.21.0.593.g511ec345e18-goog
PATCH v2 1/4 dt-bindings: usb: dwc2: Document quirk to reset PHY upon wakeup
On Rockchip rk3288 there's a hardware quirk where we need to assert the reset signal to the PHY when we get a remote wakeup on one of the two ports. Document this quirk in the bindings.
---
Changes in v2: None
Documentation/devicetree/bindings/usb/dwc2.txt | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/usb/dwc2.txt +2 -0
@@ -37,6 +37,8 @@ Refer to phy/phy-bindings.txt for generic phy consumer properties - g-rx-fifo-size: size of rx fifo size in gadget mode. - g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode. - g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode. +- snps,reset-phy-on-wake: If present indicates that we need to reset the PHY when + we detect a wakeup. This is due to a hardware errata. Deprecated properties: - g-use-dma: gadget DMA mode is automatically detected
Signature · 1 line
2.21.0.593.g511ec345e18-goog
Rob Herring
maintainerRe: [PATCH v2 1/4] dt-bindings: usb: dwc2: Document quirk to reset PHY upon wakeup
Quoted 18 lines · Douglas Anderson
On Rockchip rk3288 there's a hardware quirk where we need to assert the reset signal to the PHY when we get a remote wakeup on one of the two ports. Document this quirk in the bindings.
Signed-off-by Douglas Anderson <[email protected]>Reviewed-by Matthias Kaehlcke <[email protected]>---
Changes in v2: None
Documentation/devicetree/bindings/usb/dwc2.txt | 2 ++ 1 file changed, 2 insertions(+)Documentation/devicetree/bindings/usb/dwc2.txt +0
-0
Documentation/devicetree/bindings/usb/dwc2.txt Refer to phy/phy-bindings.txt for generic phy consumer properties · line 41
Quoted 5 lines
Documentation/devicetree/bindings/usb/dwc2.txt +2
-0@@ -37,6 +37,8 @@ Refer to phy/phy-bindings.txt for generic phy consumer properties - g-rx-fifo-size: size of rx fifo size in gadget mode. - g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode. - g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode. +- snps,reset-phy-on-wake: If present indicates that we need to reset the PHY when + we detect a wakeup. This is due to a hardware errata.
Synopsys or Rockchip errata?
Ideally, this should be implied by the controller or phy compatible.
Rob
Re: [PATCH v2 1/4] dt-bindings: usb: dwc2: Document quirk to reset PHY upon wakeup
Hi,
Quoted 28 lines · Rob Herring
Quoted 18 lines · Douglas Anderson
On Rockchip rk3288 there's a hardware quirk where we need to assert the reset signal to the PHY when we get a remote wakeup on one of the two ports. Document this quirk in the bindings.
Signed-off-by Douglas Anderson <[email protected]>Reviewed-by Matthias Kaehlcke <[email protected]>---
Changes in v2: None
Documentation/devicetree/bindings/usb/dwc2.txt | 2 ++ 1 file changed, 2 insertions(+)Documentation/devicetree/bindings/usb/dwc2.txt +0
-0Documentation/devicetree/bindings/usb/dwc2.txt Refer to phy/phy-bindings.txt for generic phy consumer properties · line 41
Quoted 5 lines
Documentation/devicetree/bindings/usb/dwc2.txt +2
-0@@ -37,6 +37,8 @@ Refer to phy/phy-bindings.txt for generic phy consumer properties - g-rx-fifo-size: size of rx fifo size in gadget mode. - g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode. - g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode. +- snps,reset-phy-on-wake: If present indicates that we need to reset the PHY when + we detect a wakeup. This is due to a hardware errata.Synopsys or Rockchip errata?
Quoted 1 line
Ideally, this should be implied by the controller or phy compatible.
I have no idea. The errata was described to me by Rockchip but I don't know if it's common to more than one board.
You're right that we could do it on the controller compatible, but we have to be careful. The two ports on rk3288 currently have the same compatible string but the errata only applies to one of them. ...so I'd have to cue on not just the compatible string but also detect whether we're on the "OTG" port of the "host only" port. That's not too hard, though since it is probe-able.
I'm happy to spin this but I'll wait to hear from Felipe. This is already in his testing tree, so presumably I should do a follow-up patch. ...but if he wants me to re-post I can do that too.
-Doug
Rob Herring
maintainerRe: [PATCH v2 1/4] dt-bindings: usb: dwc2: Document quirk to reset PHY upon wakeup
Quoted 44 lines · Doug Anderson
Hi,
Quoted 28 lines · Rob Herring
Quoted 18 lines · Douglas Anderson
On Rockchip rk3288 there's a hardware quirk where we need to assert the reset signal to the PHY when we get a remote wakeup on one of the two ports. Document this quirk in the bindings.
Signed-off-by Douglas Anderson <[email protected]>Reviewed-by Matthias Kaehlcke <[email protected]>---
Changes in v2: None
Documentation/devicetree/bindings/usb/dwc2.txt | 2 ++ 1 file changed, 2 insertions(+)Documentation/devicetree/bindings/usb/dwc2.txt +0
-0Documentation/devicetree/bindings/usb/dwc2.txt Refer to phy/phy-bindings.txt for generic phy consumer properties · line 41
Quoted 5 lines
Documentation/devicetree/bindings/usb/dwc2.txt +2
-0@@ -37,6 +37,8 @@ Refer to phy/phy-bindings.txt for generic phy consumer properties - g-rx-fifo-size: size of rx fifo size in gadget mode. - g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode. - g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode. +- snps,reset-phy-on-wake: If present indicates that we need to reset the PHY when + we detect a wakeup. This is due to a hardware errata.Synopsys or Rockchip errata?
Quoted 1 line
Ideally, this should be implied by the controller or phy compatible.
I have no idea. The errata was described to me by Rockchip but I don't know if it's common to more than one board.
You're right that we could do it on the controller compatible, but we have to be careful. The two ports on rk3288 currently have the same compatible string but the errata only applies to one of them. ...so I'd have to cue on not just the compatible string but also detect whether we're on the "OTG" port of the "host only" port. That's not too hard, though since it is probe-able.
Quoted 3 lines
I'm happy to spin this but I'll wait to hear from Felipe. This is already in his testing tree, so presumably I should do a follow-up patch. ...but if he wants me to re-post I can do that too.
Okay, I guess it is fine as-is.
Rob
PATCH v2 2/4 usb: dwc2: optionally assert phy reset when waking up
In reply to Douglas AndersonOn the rk3288 USB host-only port (the one that's not the OTG-enabled port) the PHY can get into a bad state when a wakeup is asserted (not just a wakeup from full system suspend but also a wakeup from autosuspend).
We can get the PHY out of its bad state by asserting its "port reset", but unfortunately that seems to assert a reset onto the USB bus so it could confuse things if we don't actually deenumerate / reenumerate the device.
We can also get the PHY out of its bad state by fully resetting it using the reset from the CRU (clock reset unit), which does a more full reset. The CRU-based reset appears to actually cause devices on the bus to be removed and reinserted, which fixes the problem (albeit in a hacky way).
It's unfortunate that we need to do a full re-enumeration of devices at wakeup time, but this is better than alternative of letting the bus get wedged.
---
Changes in v2:
- Cancel the work when dwc2 is freed (Matthias).
drivers/usb/dwc2/core.h | 5 +++++ drivers/usb/dwc2/core_intr.c | 12 ++++++++++++ drivers/usb/dwc2/hcd.c | 18 +++++++++++++++--- drivers/usb/dwc2/platform.c | 9 +++++++++ 4 files changed, 41 insertions(+), 3 deletions(-)
drivers/usb/dwc2/core.h +5 -0
@@ -859,6 +859,8 @@ struct dwc2_hregs_backup {* @gadget_enabled: Peripheral mode sub-driver initialization indicator. * @ll_hw_enabled: Status of low-level hardware resources. * @hibernated: True if core is hibernated +* @reset_phy_on_wake: Quirk saying that we should assert PHY reset on a +* remote wakeup. * @frame_number: Frame number read from the core. For both device * and host modes. The value ranges are from 0 * to HFNUM_MAX_FRNUM.
@@ -972,6 +974,7 @@ struct dwc2_hregs_backup {* @status_buf_dma: DMA address for status_buf * @start_work: Delayed work for handling host A-cable connection * @reset_work: Delayed work for handling a port reset +* @phy_reset_work: Work structure for doing a PHY reset * @otg_port: OTG port number * @frame_list: Frame list * @frame_list_dma: Frame list DMA address
@@ -1045,6 +1048,7 @@ struct dwc2_hsotg { unsigned int gadget_enabled:1; unsigned int ll_hw_enabled:1; unsigned int hibernated:1; + unsigned int reset_phy_on_wake:1;u16 frame_number;struct phy *phy;
@@ -1147,6 +1151,7 @@ struct dwc2_hsotg {struct delayed_work start_work;struct delayed_work reset_work; +struct work_struct phy_reset_work;u8 otg_port;u32 *frame_list;dma_addr_t frame_list_dma;
drivers/usb/dwc2/core_intr.c +12 -0
@@ -435,6 +435,18 @@ static void dwc2_handle_wakeup_detected_intr(struct dwc2_hsotg *hsotg)/* Restart the Phy Clock */ pcgcctl &= ~PCGCTL_STOPPCLK ;dwc2_writel (hsotg, pcgcctl,PCGCTL ); + +/* +* If we've got this quirk then the PHY is stuck upon +* wakeup. Assert reset. This will propagate out and +* eventually we'll re-enumerate the device. Not great +* but the best we can do. We can't call phy_reset() +* at interrupt time but there's no hurry, so we'll +* schedule it for later. +*/ +if (hsotg->reset_phy_on_wake) +schedule_work (&hsotg->phy_reset_work); +mod_timer (&hsotg->wkp_timer, jiffies +msecs_to_jiffies (71 )); }else {
drivers/usb/dwc2/hcd.c +15 -3
@@ -4376,6 +4376,17 @@ static void dwc2_hcd_reset_func(struct work_struct *work)spin_unlock_irqrestore (&hsotg->lock, flags); } +static void dwc2_hcd_phy_reset_func (struct work_struct *work) +{ + struct dwc2_hsotg *hsotg = container_of(work, struct dwc2_hsotg, + phy_reset_work); +int ret; + + ret =phy_reset (hsotg->phy); +if (ret) +dev_warn (hsotg->dev,"PHY reset failed\n" ); +} +/* * ========================================================================= * Linux HC Driver Functions
@@ -5130,6 +5141,8 @@ static void dwc2_hcd_free(struct dwc2_hsotg *hsotg)destroy_workqueue (hsotg->wq_otg); } +cancel_work_sync (&hsotg->phy_reset_work); +del_timer (&hsotg->wkp_timer); }
@@ -5271,11 +5284,10 @@ int dwc2_hcd_init(struct dwc2_hsotg *hsotg) hsotg->hc_ptr_array[i] = channel; } -/* Initialize hsotg start work */ +/* Initialize work */ INIT_DELAYED_WORK (&hsotg->start_work, dwc2_hcd_start_func); - -/* Initialize port reset work */ INIT_DELAYED_WORK (&hsotg->reset_work, dwc2_hcd_reset_func); +INIT_WORK (&hsotg->phy_reset_work, dwc2_hcd_phy_reset_func);/* * Allocate space for storing data on status transactions. Normally no
drivers/usb/dwc2/platform.c +9 -0
@@ -481,6 +481,15 @@ static int dwc2_driver_probe(struct platform_device *dev) hsotg->gadget_enabled =1 ; } + hsotg->reset_phy_on_wake = +of_property_read_bool (dev->dev.of_node, +"snps,reset-phy-on-wake" ); +if (hsotg->reset_phy_on_wake && !hsotg->phy) { +dev_warn (hsotg->dev, +"Quirk reset-phy-on-wake only supports generic PHYs\n" ); + hsotg->reset_phy_on_wake = false; + } +if (hsotg->dr_mode !=USB_DR_MODE_PERIPHERAL ) { retval =dwc2_hcd_init (hsotg);if (retval) {
Signature · 1 line
2.21.0.593.g511ec345e18-goog
PATCH v2 3/4 ARM: dts: rockchip: Hook resets up to USB PHYs on rk3288.
In reply to Douglas AndersonLet's hook up the resets to the three USB PHYs on rk3288 as per the bindings. This is in preparation for a future patch that will set the "snps,reset-phy-on-wake" on the host port.
---
Changes in v2: None
arch/arm/boot/dts/rk3288.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm/boot/dts/rk3288.dtsi +6 -0
@@ -909,6 +909,8 @@ clocks = <&cru SCLK_OTGPHY0>; clock-names = "phyclk"; #clock-cells = <0>; + resets = <&cru SRST_USBOTG_PHY>; + reset-names = "phy-reset"; }; usbphy1: usb-phy@334 {
@@ -917,6 +919,8 @@ clocks = <&cru SCLK_OTGPHY1>; clock-names = "phyclk"; #clock-cells = <0>; + resets = <&cru SRST_USBHOST0_PHY>; + reset-names = "phy-reset"; }; usbphy2: usb-phy@348 {
@@ -925,6 +929,8 @@ clocks = <&cru SCLK_OTGPHY2>; clock-names = "phyclk"; #clock-cells = <0>; + resets = <&cru SRST_USBHOST1_PHY>; + reset-names = "phy-reset"; }; }; };
Signature · 1 line
2.21.0.593.g511ec345e18-goog
PATCH v2 4/4 ARM: dts: rockchip: Add quirk for resetting rk3288's dwc2 host on wakeup
In reply to Douglas AndersonThe "host" USB port on rk3288 has a hardware errata where we've got to assert a PHY reset whenever we see a remote wakeup. Add that quirk property to the device tree.
---
Changes in v2: None
arch/arm/boot/dts/rk3288.dtsi | 1 + 1 file changed, 1 insertion(+)
arch/arm/boot/dts/rk3288.dtsi +1 -0
@@ -621,6 +621,7 @@ dr_mode = "host"; phys = <&usbphy2>; phy-names = "usb2-phy"; + snps,reset-phy-on-wake; status = "disabled"; };
Signature · 1 line
2.21.0.593.g511ec345e18-goog