Skip to contentSkip to conversation

(no subject)

U-Boot New Adam Ford 2 participants 10 messages Apr 28, 2019 – Apr 30, 2019

Subsystems (5)
lore
Share & tools
lore
author
#1 lore raw

PATCH 1/4 usb: ohci: Re-enable commented out delay

There is a delay function that was commented out. This patch re-enables it, because it will be needed for da850 ohci support.

drivers/usb/host/ohci-hcd.c +0 -2
index 3b6f889f7b..2b0df88f49 100644
@@ -1545,10 +1545,8 @@ static int submit_common_msg(ohci_t *ohci, struct usb_device *dev,
 		return -1;
 	}
 
-#if 0
 	mdelay(10);
 	/* ohci_dump_status(ohci); */
-#endif
 
 	timeout = USB_TIMEOUT_MS(pipe);
 
Signature · 1 line
2.17.1
Applied
#2 lore raw

PATCH 1/4 usb: ohci: Re-enable commented out delay

Quoted 11 lines · Adam Ford

There is a delay function that was commented out. This patch re-enables it, because it will be needed for da850 ohci support.

drivers/usb/host/ohci-hcd.c +0 -0
index 3b6f889f7b..2b0df88f49 100644

drivers/usb/host/ohci-hcd.c static int submit_common_msg(ohci_t *ohci, struct usb_device *dev, · line 1552

Quoted 10 lines
drivers/usb/host/ohci-hcd.c +0 -2
@@ -1545,10 +1545,8 @@ static int submit_common_msg(ohci_t *ohci, struct usb_device *dev,
 		return -1;
 	}
 
-#if 0
 	mdelay(10);
 	/* ohci_dump_status(ohci); */
-#endif
 
 	timeout = USB_TIMEOUT_MS(pipe);
 

Applied, since this was probably broken since 2006.

Signature · 2 lines
Best regards,
Marek Vasut
author
#3 lore raw

PATCH 2/4 ARM: davinci: Remove unused functions from header

In reply to Adam Ford

There are a few functions defined in the header file, but they are not referenced by any Davinci code. In order to make a general function in the future with static function declarations, this patch will remove the references all together.

arch/arm/mach-davinci/include/mach/da8xx-usb.h +0 -3
index 42e1258225..215706e172 100644
@@ -86,7 +86,4 @@ struct da8xx_usb_regs {
 
 #define DA8XX_USB_VBUS_GPIO	(1 << 15)
 
-int usb_phy_on(void);
-void usb_phy_off(void);
-
 #endif	/* __DA8XX_MUSB_H__ */
Signature · 1 line
2.17.1
Applied
#4 lore raw

PATCH 2/4 ARM: davinci: Remove unused functions from header

Quoted 13 lines · Adam Ford

There are a few functions defined in the header file, but they are not referenced by any Davinci code. In order to make a general function in the future with static function declarations, this patch will remove the references all together.

arch/arm/mach-davinci/include/mach/da8xx-usb.h +0 -0
index 42e1258225..215706e172 100644

arch/arm/mach-davinci/include/mach/da8xx-usb.h struct da8xx_usb_regs { · line 89

Quoted 7 lines
arch/arm/mach-davinci/include/mach/da8xx-usb.h +0 -3
@@ -86,7 +86,4 @@ struct da8xx_usb_regs {
 
 #define DA8XX_USB_VBUS_GPIO	(1 << 15)
 
-int usb_phy_on(void);
-void usb_phy_off(void);
-
 #endif	/* __DA8XX_MUSB_H__ */

Applied, thanks

Signature · 2 lines
Best regards,
Marek Vasut
author
#5 lore raw

PATCH 3/4 usb: ohci: ohci-da8xx: Enable da850-ohci driver with DM support

In reply to Adam Ford

This patch reuses some former code for the hawkboard, combines it with some some similar DM_USB compatible code for the OHCI driver, and enables the use of the da850's OHCI controller with DM_USB compatibility.

drivers/usb/host/Kconfig +5 -0
index 0fbc115801..0d8ab3b651 100644
@@ -239,6 +239,11 @@ config USB_OHCI_GENERIC
 	---help---
 	  Enables support for generic OHCI controller.
 
+config USB_OHCI_DA8XX
+	bool "Support for da850 OHCI USB controller"
+	help
+	  Enable support for the da850 USB controller.
+
 endif # USB_OHCI_HCD
 
 config USB_UHCI_HCD
drivers/usb/host/ohci-da8xx.c +146 -1

158 lines not on this page · raw message

Signature · 1 line
2.17.1
#6 lore raw

PATCH 3/4 usb: ohci: ohci-da8xx: Enable da850-ohci driver with DM support

Quoted 58 lines · Adam Ford

This patch reuses some former code for the hawkboard, combines it with some some similar DM_USB compatible code for the OHCI driver, and enables the use of the da850's OHCI controller with DM_USB compatibility.

drivers/usb/host/Kconfig +5 -0
index 0fbc115801..0d8ab3b651 100644
@@ -239,6 +239,11 @@ config USB_OHCI_GENERIC
 	---help---
 	  Enables support for generic OHCI controller.
 
+config USB_OHCI_DA8XX
+	bool "Support for da850 OHCI USB controller"
+	help
+	  Enable support for the da850 USB controller.
+
 endif # USB_OHCI_HCD
 
 config USB_UHCI_HCD
drivers/usb/host/ohci-da8xx.c +24 -1
index 47ad3f34d5..0f38791973 100644
@@ -4,9 +4,63 @@
  */
 
 #include <common.h>
-
+#include <asm/io.h>
+#include <clk.h>
+#include <dm.h>
+#include <dm/ofnode.h>
+#include <generic-phy.h>
+#include <reset.h>
+#include "ohci.h"
 #include <asm/arch/da8xx-usb.h>
 
+struct da8xx_ohci {
+	ohci_t ohci;
+	struct clk *clocks;	/* clock list */
+	struct phy phy;
+	int clock_count;	/* number of clock in clock list */
+};
+
+static int usb_phy_on(void)
+{
+	u32 timeout;
+	u32 cfgchip2;
+
+	cfgchip2 = readl(&davinci_syscfg_regs->cfgchip2);
+
+	cfgchip2 &= ~(CFGCHIP2_RESET | CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN |
+		      CFGCHIP2_OTGMODE | CFGCHIP2_REFFREQ |
+		      CFGCHIP2_USB1PHYCLKMUX);

drivers/usb/host/ohci-da8xx.c line 42

Quoted 10 lines
drivers/usb/host/ohci-da8xx.c +10 -0
+	cfgchip2 |= CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN | CFGCHIP2_PHY_PLLON |
+		    CFGCHIP2_REFFREQ_24MHZ | CFGCHIP2_USB2PHYCLKMUX |
+		    CFGCHIP2_USB1SUSPENDM;
+
+	writel(cfgchip2, &davinci_syscfg_regs->cfgchip2);
+
+	/* wait until the usb phy pll locks */
+	timeout = 0x7FFFFFF;
+
+	while (timeout--) {

Use get_timer() for the timeout.

Quoted 9 lines
drivers/usb/host/ohci-da8xx.c +9 -0
+		if (readl(&davinci_syscfg_regs->cfgchip2) & CFGCHIP2_PHYCLKGD)
+			return 1;
+	}
+
+	/* USB phy was not turned on */
+	return 0;
+}
+
+static void usb_phy_off(void)

drivers/usb/host/ohci-da8xx.c line 61

Quoted 10 lines
drivers/usb/host/ohci-da8xx.c +10 -0
+{
+	u32 cfgchip2;
+
+	/*
+	 * Power down the on-chip PHY.
+	 */
+	cfgchip2 = readl(&davinci_syscfg_regs->cfgchip2);
+	cfgchip2 &= ~(CFGCHIP2_PHY_PLLON | CFGCHIP2_USB1SUSPENDM);
+	cfgchip2 |= CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN | CFGCHIP2_RESET;
+	writel(cfgchip2, &davinci_syscfg_regs->cfgchip2);

clrsetbits

Quoted 15 lines
drivers/usb/host/ohci-da8xx.c +8 -0
+}
+
 int usb_cpu_init(void)
 {
 	/* enable psc for usb2.0 */
@@ -37,3 +91,94 @@ int usb_cpu_init_fail(void)
 {
 	return usb_cpu_stop();
 }
+
+#if CONFIG_IS_ENABLED(DM_USB)
+static int ohci_da8xx_probe(struct udevice *dev)
+{
+	struct ohci_regs *regs = (struct ohci_regs *)devfdt_get_addr(dev);
+	struct da8xx_ohci *priv = dev_get_priv(dev);

drivers/usb/host/ohci-da8xx.c int usb_cpu_init_fail(void) · line 109

Quoted 10 lines
drivers/usb/host/ohci-da8xx.c +10 -0
+	int i, err, ret, clock_nb;
+
+	err = 0;
+	priv->clock_count = 0;
+	clock_nb = dev_count_phandle_with_args(dev, "clocks", "#clock-cells");
+	if (clock_nb > 0) {
+		priv->clocks = devm_kcalloc(dev, clock_nb, sizeof(struct clk),
+					    GFP_KERNEL);
+		if (!priv->clocks)
+			return -ENOMEM;

clk_enable_bulk()

Quoted 75 lines
drivers/usb/host/ohci-da8xx.c +74 -0
+		for (i = 0; i < clock_nb; i++) {
+			err = clk_get_by_index(dev, i, &priv->clocks[i]);
+			if (err < 0)
+				break;
+
+			err = clk_enable(&priv->clocks[i]);
+			if (err) {
+				dev_err(dev, "failed to enable clock %d\n", i);
+				clk_free(&priv->clocks[i]);
+				goto clk_err;
+			}
+			priv->clock_count++;
+		}
+	} else if (clock_nb != -ENOENT) {
+		dev_err(dev, "failed to get clock phandle(%d)\n", clock_nb);
+		return clock_nb;
+	}
+
+	err = usb_cpu_init();
+
+	if (err)
+		goto clk_err;
+
+	err = ohci_register(dev, regs);
+	if (err)
+		goto phy_err;
+
+	return 0;
+
+phy_err:
+	ret = usb_cpu_stop();
+	if (ret)
+		dev_err(dev, "failed to shutdown usb phy\n");
+
+clk_err:
+	ret = clk_release_all(priv->clocks, priv->clock_count);
+	if (ret)
+		dev_err(dev, "failed to disable all clocks\n");
+
+	return err;
+}
+
+static int ohci_da8xx_remove(struct udevice *dev)
+{
+	struct da8xx_ohci *priv = dev_get_priv(dev);
+	int ret;
+
+	ret = ohci_deregister(dev);
+	if (ret)
+		return ret;
+
+	ret = usb_cpu_stop();
+	if (ret)
+		return ret;
+
+	return clk_release_all(priv->clocks, priv->clock_count);
+}
+
+static const struct udevice_id da8xx_ohci_ids[] = {
+	{ .compatible = "ti,da830-ohci" },
+	{ }
+};
+
+U_BOOT_DRIVER(ohci_generic) = {
+	.name	= "ohci-da8xx",
+	.id	= UCLASS_USB,
+	.of_match = da8xx_ohci_ids,
+	.probe = ohci_da8xx_probe,
+	.remove = ohci_da8xx_remove,
+	.ops	= &ohci_usb_ops,
+	.priv_auto_alloc_size = sizeof(struct da8xx_ohci),
+	.flags	= DM_FLAG_ALLOC_PRIV_DMA,
+};
+#endif
Signature · 2 lines
Best regards,
Marek Vasut
author
#7 lore raw

PATCH 3/4 usb: ohci: ohci-da8xx: Enable da850-ohci driver with DM support

Quoted 86 lines · Marek Vasut
Quoted 58 lines · Adam Ford

This patch reuses some former code for the hawkboard, combines it with some some similar DM_USB compatible code for the OHCI driver, and enables the use of the da850's OHCI controller with DM_USB compatibility.

drivers/usb/host/Kconfig +5 -0
index 0fbc115801..0d8ab3b651 100644
@@ -239,6 +239,11 @@ config USB_OHCI_GENERIC
      ---help---
        Enables support for generic OHCI controller.
 
+config USB_OHCI_DA8XX
+     bool "Support for da850 OHCI USB controller"
+     help
+       Enable support for the da850 USB controller.
+
 endif # USB_OHCI_HCD
 
 config USB_UHCI_HCD
drivers/usb/host/ohci-da8xx.c +24 -1
index 47ad3f34d5..0f38791973 100644
@@ -4,9 +4,63 @@
  */
 
 #include <common.h>
-
+#include <asm/io.h>
+#include <clk.h>
+#include <dm.h>
+#include <dm/ofnode.h>
+#include <generic-phy.h>
+#include <reset.h>
+#include "ohci.h"
 #include <asm/arch/da8xx-usb.h>
 
+struct da8xx_ohci {
+     ohci_t ohci;
+     struct clk *clocks;     /* clock list */
+     struct phy phy;
+     int clock_count;        /* number of clock in clock list */
+};
+
+static int usb_phy_on(void)
+{
+     u32 timeout;
+     u32 cfgchip2;
+
+     cfgchip2 = readl(&davinci_syscfg_regs->cfgchip2);
+
+     cfgchip2 &= ~(CFGCHIP2_RESET | CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN |
+                   CFGCHIP2_OTGMODE | CFGCHIP2_REFFREQ |
+                   CFGCHIP2_USB1PHYCLKMUX);

drivers/usb/host/ohci-da8xx.c line 42

Quoted 10 lines
drivers/usb/host/ohci-da8xx.c +10 -0
+     cfgchip2 |= CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN | CFGCHIP2_PHY_PLLON |
+                 CFGCHIP2_REFFREQ_24MHZ | CFGCHIP2_USB2PHYCLKMUX |
+                 CFGCHIP2_USB1SUSPENDM;
+
+     writel(cfgchip2, &davinci_syscfg_regs->cfgchip2);
+
+     /* wait until the usb phy pll locks */
+     timeout = 0x7FFFFFF;
+
+     while (timeout--) {

Use get_timer() for the timeout.

Quoted 13 lines
drivers/usb/host/ohci-da8xx.c +13 -0
+             if (readl(&davinci_syscfg_regs->cfgchip2) & CFGCHIP2_PHYCLKGD)
+                     return 1;
+     }
+
+     /* USB phy was not turned on */
+     return 0;
+}
+
+static void usb_phy_off(void)
+{
+     u32 cfgchip2;
+
+     /*
Quoted 8 lines

drivers/usb/host/ohci-da8xx.c line 61

Quoted 6 lines
drivers/usb/host/ohci-da8xx.c +6 -0
+      * Power down the on-chip PHY.
+      */
+     cfgchip2 = readl(&davinci_syscfg_regs->cfgchip2);
+     cfgchip2 &= ~(CFGCHIP2_PHY_PLLON | CFGCHIP2_USB1SUSPENDM);
+     cfgchip2 |= CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN | CFGCHIP2_RESET;
+     writel(cfgchip2, &davinci_syscfg_regs->cfgchip2);

clrsetbits

Marek - I will be submitting a V2 with your suggestions. It seems like some of the segments are going to be applied, do you want just do a V2 on the this one, or re-submit the whole series?

Quoted 109 lines
Quoted 16 lines
drivers/usb/host/ohci-da8xx.c +8 -0
+}
+
 int usb_cpu_init(void)
 {
      /* enable psc for usb2.0 */
@@ -37,3 +91,94 @@ int usb_cpu_init_fail(void)
 {
      return usb_cpu_stop();
 }
+
+#if CONFIG_IS_ENABLED(DM_USB)
+static int ohci_da8xx_probe(struct udevice *dev)
+{
+     struct ohci_regs *regs = (struct ohci_regs *)devfdt_get_addr(dev);
+     struct da8xx_ohci *priv = dev_get_priv(dev);

drivers/usb/host/ohci-da8xx.c int usb_cpu_init_fail(void) · line 109

Quoted 10 lines
drivers/usb/host/ohci-da8xx.c +10 -0
+     int i, err, ret, clock_nb;
+
+     err = 0;
+     priv->clock_count = 0;
+     clock_nb = dev_count_phandle_with_args(dev, "clocks", "#clock-cells");
+     if (clock_nb > 0) {
+             priv->clocks = devm_kcalloc(dev, clock_nb, sizeof(struct clk),
+                                         GFP_KERNEL);
+             if (!priv->clocks)
+                     return -ENOMEM;

clk_enable_bulk()

Quoted 65 lines
drivers/usb/host/ohci-da8xx.c +64 -0
+             for (i = 0; i < clock_nb; i++) {
+                     err = clk_get_by_index(dev, i, &priv->clocks[i]);
+                     if (err < 0)
+                             break;
+
+                     err = clk_enable(&priv->clocks[i]);
+                     if (err) {
+                             dev_err(dev, "failed to enable clock %d\n", i);
+                             clk_free(&priv->clocks[i]);
+                             goto clk_err;
+                     }
+                     priv->clock_count++;
+             }
+     } else if (clock_nb != -ENOENT) {
+             dev_err(dev, "failed to get clock phandle(%d)\n", clock_nb);
+             return clock_nb;
+     }
+
+     err = usb_cpu_init();
+
+     if (err)
+             goto clk_err;
+
+     err = ohci_register(dev, regs);
+     if (err)
+             goto phy_err;
+
+     return 0;
+
+phy_err:
+     ret = usb_cpu_stop();
+     if (ret)
+             dev_err(dev, "failed to shutdown usb phy\n");
+
+clk_err:
+     ret = clk_release_all(priv->clocks, priv->clock_count);
+     if (ret)
+             dev_err(dev, "failed to disable all clocks\n");
+
+     return err;
+}
+
+static int ohci_da8xx_remove(struct udevice *dev)
+{
+     struct da8xx_ohci *priv = dev_get_priv(dev);
+     int ret;
+
+     ret = ohci_deregister(dev);
+     if (ret)
+             return ret;
+
+     ret = usb_cpu_stop();
+     if (ret)
+             return ret;
+
+     return clk_release_all(priv->clocks, priv->clock_count);
+}
+
+static const struct udevice_id da8xx_ohci_ids[] = {
+     { .compatible = "ti,da830-ohci" },
+     { }
+};
+
+U_BOOT_DRIVER(ohci_generic) = {

drivers/usb/host/ohci-da8xx.c int usb_cpu_init_fail(void) · line 184

Quoted 10 lines
drivers/usb/host/ohci-da8xx.c +10 -0
+     .name   = "ohci-da8xx",
+     .id     = UCLASS_USB,
+     .of_match = da8xx_ohci_ids,
+     .probe = ohci_da8xx_probe,
+     .remove = ohci_da8xx_remove,
+     .ops    = &ohci_usb_ops,
+     .priv_auto_alloc_size = sizeof(struct da8xx_ohci),
+     .flags  = DM_FLAG_ALLOC_PRIV_DMA,
+};
+#endif

--
Best regards,
Marek Vasut

#8 lore raw

PATCH 3/4 usb: ohci: ohci-da8xx: Enable da850-ohci driver with DM support

Quoted 96 lines · Adam Ford
Quoted 86 lines · Marek Vasut
Quoted 58 lines · Adam Ford

This patch reuses some former code for the hawkboard, combines it with some some similar DM_USB compatible code for the OHCI driver, and enables the use of the da850's OHCI controller with DM_USB compatibility.

drivers/usb/host/Kconfig +5 -0
index 0fbc115801..0d8ab3b651 100644
@@ -239,6 +239,11 @@ config USB_OHCI_GENERIC
      ---help---
        Enables support for generic OHCI controller.
 
+config USB_OHCI_DA8XX
+     bool "Support for da850 OHCI USB controller"
+     help
+       Enable support for the da850 USB controller.
+
 endif # USB_OHCI_HCD
 
 config USB_UHCI_HCD
drivers/usb/host/ohci-da8xx.c +24 -1
index 47ad3f34d5..0f38791973 100644
@@ -4,9 +4,63 @@
  */
 
 #include <common.h>
-
+#include <asm/io.h>
+#include <clk.h>
+#include <dm.h>
+#include <dm/ofnode.h>
+#include <generic-phy.h>
+#include <reset.h>
+#include "ohci.h"
 #include <asm/arch/da8xx-usb.h>
 
+struct da8xx_ohci {
+     ohci_t ohci;
+     struct clk *clocks;     /* clock list */
+     struct phy phy;
+     int clock_count;        /* number of clock in clock list */
+};
+
+static int usb_phy_on(void)
+{
+     u32 timeout;
+     u32 cfgchip2;
+
+     cfgchip2 = readl(&davinci_syscfg_regs->cfgchip2);
+
+     cfgchip2 &= ~(CFGCHIP2_RESET | CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN |
+                   CFGCHIP2_OTGMODE | CFGCHIP2_REFFREQ |
+                   CFGCHIP2_USB1PHYCLKMUX);

drivers/usb/host/ohci-da8xx.c line 42

Quoted 10 lines
drivers/usb/host/ohci-da8xx.c +10 -0
+     cfgchip2 |= CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN | CFGCHIP2_PHY_PLLON |
+                 CFGCHIP2_REFFREQ_24MHZ | CFGCHIP2_USB2PHYCLKMUX |
+                 CFGCHIP2_USB1SUSPENDM;
+
+     writel(cfgchip2, &davinci_syscfg_regs->cfgchip2);
+
+     /* wait until the usb phy pll locks */
+     timeout = 0x7FFFFFF;
+
+     while (timeout--) {

Use get_timer() for the timeout.

Quoted 13 lines
drivers/usb/host/ohci-da8xx.c +13 -0
+             if (readl(&davinci_syscfg_regs->cfgchip2) & CFGCHIP2_PHYCLKGD)
+                     return 1;
+     }
+
+     /* USB phy was not turned on */
+     return 0;
+}
+
+static void usb_phy_off(void)
+{
+     u32 cfgchip2;
+
+     /*
Quoted 8 lines

drivers/usb/host/ohci-da8xx.c line 61

Quoted 6 lines
drivers/usb/host/ohci-da8xx.c +6 -0
+      * Power down the on-chip PHY.
+      */
+     cfgchip2 = readl(&davinci_syscfg_regs->cfgchip2);
+     cfgchip2 &= ~(CFGCHIP2_PHY_PLLON | CFGCHIP2_USB1SUSPENDM);
+     cfgchip2 |= CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN | CFGCHIP2_RESET;
+     writel(cfgchip2, &davinci_syscfg_regs->cfgchip2);

clrsetbits

Quoted 3 lines

Marek - I will be submitting a V2 with your suggestions. It seems like some of the segments are going to be applied, do you want just do a V2 on the this one, or re-submit the whole series?

Just 3/4 and 4/4 is enough. Rebase on u-boot-usb/master and make sure not to drop $subject from the cover letter (this series has it empty, which made me almost miss it)

Signature · 2 lines
Best regards,
Marek Vasut
author
#9 lore raw

PATCH 4/4 ARM: da850evm: Enable da850-ohci USB host controller

In reply to Adam Ford

The DA850 EVM has one USB 1.1 OHCI Host controller. With the host controller now support DM_USB, this patch enables the respective functions for the da850evm.

configs/da850evm_defconfig +6 -1
index ee39b0b1bc..1845813b2e 100644
@@ -8,8 +8,8 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SYS_MALLOC_F_LEN=0x800
 CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
 CONFIG_NR_DRAM_BANKS=1
+CONFIG_SPL=y
 CONFIG_SPL_SPI_FLASH_SUPPORT=y
 CONFIG_SPL_SPI_SUPPORT=y
 CONFIG_SYS_EXTRA_OPTIONS="MAC_ADDR_IN_SPIFLASH"
@@ -67,5 +67,10 @@ CONFIG_SYS_NS16550=y
 CONFIG_SPI=y
 CONFIG_DM_SPI=y
 CONFIG_DAVINCI_SPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+# CONFIG_SPL_DM_USB is not set
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_DA8XX=y
 # CONFIG_FAT_WRITE is not set
 CONFIG_USE_TINY_PRINTF=y
include/configs/da850evm.h +8 -0
index 94848f5128..9aaecdd1d5 100644
@@ -267,6 +267,14 @@
 #define CONFIG_ENV_SIZE		(16 << 10)
 #endif
 
+/* USB Configs */
+#define CONFIG_SYS_USB_OHCI_CPU_INIT
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_USB_STORAGE
+#define CONFIG_SYS_USB_OHCI_REGS_BASE		0x01E25000
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	15
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME		"da850evm"
+
 #ifndef CONFIG_DIRECT_NOR_BOOT
 /* defines for SPL */
 #define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SYS_TEXT_BASE - \
Signature · 1 line
2.17.1