Skip to contentSkip to conversation

MTK NAND driver improvements and fixes

PATCH Superseded Xiaolei Li 5 participants 17 messages Apr 30, 2019 – May 6, 2019 2 messages not in the archive

Subsystems (5)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Xiaolei Li

author
#0 lore raw

v2 cover MTK NAND driver improvements and fixes

The following patch set mainly contains:
* Fix low level time calculation of read/write cycle to meet tRC_min and tWC_min requirements.
* Refine RE# pulse width calculation and data sampling to improve read performance.
* Add CS validity check.
* Fix oob buffer pointer wrongly setting and empty page threshold setting.

Changes on v2 relative to:
--------------------

tree : git://git.infradead.org/linux-mtd.git
branch : master
commit :

        'commit 3e35730dd754 ("mtd: powernv_flash: Fix device
         registration error")

Patch v2:
---------
- Fix type
- Reference correct faulty patch
- Refine code to do calculation and condition in separate steps
- Fix empty threshold calculation

Tests:
------

* ubifs and jffs2 are validated on NAND device MT29F16G08ADBCA by 'dd' command.
* all drivers/mtd/tests/* pass.
* speed test:
eraseblock write speed is 11087 KiB/s
eraseblock read speed is 19986 KiB/s
page write speed is 10689 KiB/s
page read speed is 18724 KiB/s
2 page write speed is 10611 KiB/s
2 page read speed is 18713 KiB/s
erase speed is 103696 KiB/s
2x multi-block erase speed is 354248 KiB/s
4x multi-block erase speed is 350459 KiB/s
8x multi-block erase speed is 356173 KiB/s
16x multi-block erase speed is 356173 KiB/s
32x multi-block erase speed is 358120 KiB/s
64x multi-block erase speed is 356173 KiB/s

Xiaolei Li (5):
mtd: rawnand: mtk: Correct low level time calculation of r/w cycle
mtd: rawnand: mtk: Improve data sampling timing for read cycle
mtd: rawnand: mtk: Add validity check for CE# pin setting
mtd: rawnand: mtk: Fix wrongly assigned OOB buffer pointer issue
mtd: rawnand: mtk: Setup empty page threshold correctly

 drivers/mtd/nand/raw/mtk_nand.c | 93 ++++++++++++++++++++++++++++-----
 1 file changed, 79 insertions(+), 14 deletions(-)
Signature · 7 lines
2.18.0



______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
author
#1 lore raw

PATCH v2 1/5 mtd: rawnand: mtk: Correct low level time calculation of r/w cycle

At present, the flow of calculating AC timing of read/write cycle in SDR mode is that:
At first, calculate high hold time which is valid for both read and write cycle using the max value between tREH_min and tWH_min. Secondly, calculate WE# pulse width using tWP_min.
Thridly, calculate RE# pulse width using the bigger one between tREA_max and tRP_min.

But NAND SPEC shows that Controller should also meet write/read cycle time. That is write cycle time should be more than tWC_min and read cycle should be more than tRC_min. Obviously, we do not achieve that now.

This patch corrects the low level time calculation to meet minimum read/write cycle time required. After getting the high hold time, WE# low level time will be promised to meet tWP_min and tWC_min requirement, and RE# low level time will be promised to meet tREA_max, tRP_min and tRC_min requirement.

Fixes edfee3619c49 ("mtd: nand: mtk: add ->setup_data_interface() hook")
---
 drivers/mtd/nand/raw/mtk_nand.c | 24 +++++++++++++++++++++---
 1 file changed, 21 insertions(+), 3 deletions(-)
drivers/mtd/nand/raw/mtk_nand.c +21 -3
index b6b4602f5132..4fbb0c6ecae3 100644
@@ -508,7 +508,8 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
 {
 	struct mtk_nfc *nfc = nand_get_controller_data(chip);
 	const struct nand_sdr_timings *timings;
-	u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst, trlt;
+	u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst = 0, trlt = 0;
+	u32 thold;
 
 	timings = nand_get_sdr_timings(conf);
 	if (IS_ERR(timings))
@@ -544,11 +545,28 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
 	twh = DIV_ROUND_UP(twh * rate, 1000000) - 1;
 	twh &= 0xf;
 
-	twst = timings->tWP_min / 1000;
+	/* Calculate real WE#/RE# hold time in nanosecond */
+	thold = (twh + 1) * 1000000 / rate;
+	/* nanosecond to picosecond */
+	thold *= 1000;
+
+	/**
+	 * WE# low level time should be expaned to meet WE# pulse time
+	 * and WE# cycle time at the same time.
+	 */
+	if (thold < timings->tWC_min)
+		twst = timings->tWC_min - thold;
+	twst = max(timings->tWP_min, twst) / 1000;
 	twst = DIV_ROUND_UP(twst * rate, 1000000) - 1;
 	twst &= 0xf;
 
-	trlt = max(timings->tREA_max, timings->tRP_min) / 1000;
+	/**
+	 * RE# low level time should be expaned to meet RE# pulse time,
+	 * RE# access time and RE# cycle time at the same time.
+	 */
+	if (thold < timings->tRC_min)
+		trlt = timings->tRC_min - thold;
+	trlt = max3(trlt, timings->tREA_max, timings->tRP_min) / 1000;
 	trlt = DIV_ROUND_UP(trlt * rate, 1000000) - 1;
 	trlt &= 0xf;
 
Signature · 1 line
2.18.0
maintainer
#2 lore raw

Re: [PATCH v2 1/5] mtd: rawnand: mtk: Correct low level time calculation of r/w cycle

Hi,

[This is an automated email]

This commit has been processed because it contains a "Fixes:" tag, fixing commit: edfee3619c49 mtd: nand: mtk: add ->setup_data_interface() hook.

The bot has tested the following trees: v5.0.10, v4.19.37, v4.14.114.

v5.0.10: Build OK!
v4.19.37: Build OK!
v4.14.114: Failed to apply! Possible dependencies:
Unable to calculate

How should we proceed with this patch?

--
Thanks,
Sasha

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

author
#3 lore raw

Re: [PATCH v2 1/5] mtd: rawnand: mtk: Correct low level time calculation of r/w cycle

Hi Sasha,

I am not sure if it is caused by raw NAND code path change.

Raw NAND code was moved from mtd/nand to mtd/nand/raw subdirectory since kernel v4.17.

The fixing commit: edfee3619c49 mtd: nand: mtk:
add->setup_data_interface() hook exists before kernel v4.17.

@Miquel, do you know if some other raw NAND driver ever encountered this case? Thanks.

Quoted 15 lines · Sasha Levin

Hi,

[This is an automated email]

This commit has been processed because it contains a "Fixes:" tag, fixing commit: edfee3619c49 mtd: nand: mtk: add ->setup_data_interface() hook.

The bot has tested the following trees: v5.0.10, v4.19.37, v4.14.114.

v5.0.10: Build OK!
v4.19.37: Build OK!
v4.14.114: Failed to apply! Possible dependencies:
Unable to calculate

Quoted 5 lines

How should we proceed with this patch?

--
Thanks,
Sasha

Thanks,
Xiaolei

maintainer
#4 lore raw

Re: [PATCH v2 1/5] mtd: rawnand: mtk: Correct low level time calculation of r/w cycle

Hi xiaolei,

xiaolei li <[email protected]> wrote on Sun, 5 May 2019 15:06:40 +0800:

Quoted 4 lines

Hi Sasha,

I am not sure if it is caused by raw NAND code path change.

Quoted 8 lines

Raw NAND code was moved from mtd/nand to mtd/nand/raw subdirectory since kernel v4.17.

The fixing commit: edfee3619c49 mtd: nand: mtk:
add->setup_data_interface() hook exists before kernel v4.17.

@Miquel, do you know if some other raw NAND driver ever encountered this case? Thanks.

Don't know. Just checkout a 4.14.114 and try to apply the patch :)

Quoted 8 lines · Sasha Levin
Quoted 6 lines

Hi,

[This is an automated email]

This commit has been processed because it contains a "Fixes:" tag, fixing commit: edfee3619c49 mtd: nand: mtk: add ->setup_data_interface() hook.

Thanks,
Miquèl

maintainer Reviewed-by on v2 1/5
#5 lore raw

Re: [PATCH v2 1/5] mtd: rawnand: mtk: Correct low level time calculation of r/w cycle

In reply to Xiaolei Li

Hi Xiaolei,

Xiaolei Li <[email protected]> wrote on Tue, 30 Apr 2019 18:02:46 +0800:

Quoted 40 lines

At present, the flow of calculating AC timing of read/write cycle in SDR mode is that:
At first, calculate high hold time which is valid for both read and write cycle using the max value between tREH_min and tWH_min. Secondly, calculate WE# pulse width using tWP_min.
Thridly, calculate RE# pulse width using the bigger one between tREA_max and tRP_min.

But NAND SPEC shows that Controller should also meet write/read cycle time. That is write cycle time should be more than tWC_min and read cycle should be more than tRC_min. Obviously, we do not achieve that now.

This patch corrects the low level time calculation to meet minimum read/write cycle time required. After getting the high hold time, WE# low level time will be promised to meet tWP_min and tWC_min requirement, and RE# low level time will be promised to meet tREA_max, tRP_min and tRC_min requirement.

Fixes edfee3619c49 ("mtd: nand: mtk: add ->setup_data_interface() hook")
---
 drivers/mtd/nand/raw/mtk_nand.c | 24 +++++++++++++++++++++---
 1 file changed, 21 insertions(+), 3 deletions(-)
drivers/mtd/nand/raw/mtk_nand.c +2 -1
index b6b4602f5132..4fbb0c6ecae3 100644
@@ -508,7 +508,8 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
 {
 	struct mtk_nfc *nfc = nand_get_controller_data(chip);
 	const struct nand_sdr_timings *timings;
-	u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst, trlt;
+	u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst = 0, trlt = 0;
+	u32 thold;
 
 	timings = nand_get_sdr_timings(conf);
 	if (IS_ERR(timings))

drivers/mtd/nand/raw/mtk_nand.c static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline, · line 553

Quoted 10 lines
drivers/mtd/nand/raw/mtk_nand.c +6 -1
@@ -544,11 +545,28 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
 	twh = DIV_ROUND_UP(twh * rate, 1000000) - 1;
 	twh &= 0xf;
 
-	twst = timings->tWP_min / 1000;
+	/* Calculate real WE#/RE# hold time in nanosecond */
+	thold = (twh + 1) * 1000000 / rate;
+	/* nanosecond to picosecond */
+	thold *= 1000;
+
+	/**
        /*

drivers/mtd/nand/raw/mtk_nand.c static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline, · line 563

Quoted 11 lines
drivers/mtd/nand/raw/mtk_nand.c +7 -1
+	 * WE# low level time should be expaned to meet WE# pulse time
+	 * and WE# cycle time at the same time.
+	 */
+	if (thold < timings->tWC_min)
+		twst = timings->tWC_min - thold;
+	twst = max(timings->tWP_min, twst) / 1000;
 	twst = DIV_ROUND_UP(twst * rate, 1000000) - 1;
 	twst &= 0xf;
 
-	trlt = max(timings->tREA_max, timings->tRP_min) / 1000;
+	/**

Ditto

drivers/mtd/nand/raw/mtk_nand.c static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline, · line 572

Quoted 9 lines
drivers/mtd/nand/raw/mtk_nand.c +6 -0
+	 * RE# low level time should be expaned to meet RE# pulse time,
+	 * RE# access time and RE# cycle time at the same time.
+	 */
+	if (thold < timings->tRC_min)
+		trlt = timings->tRC_min - thold;
+	trlt = max3(trlt, timings->tREA_max, timings->tRP_min) / 1000;
 	trlt = DIV_ROUND_UP(trlt * rate, 1000000) - 1;
 	trlt &= 0xf;
 

With this fixed:

Thanks,
Miquèl

author
#6 lore raw

Re: [PATCH v2 1/5] mtd: rawnand: mtk: Correct low level time calculation of r/w cycle

Quoted 67 lines · Miquel Raynal

Hi Xiaolei,

Xiaolei Li <[email protected]> wrote on Tue, 30 Apr 2019 18:02:46 +0800:

Quoted 40 lines

At present, the flow of calculating AC timing of read/write cycle in SDR mode is that:
At first, calculate high hold time which is valid for both read and write cycle using the max value between tREH_min and tWH_min. Secondly, calculate WE# pulse width using tWP_min.
Thridly, calculate RE# pulse width using the bigger one between tREA_max and tRP_min.

But NAND SPEC shows that Controller should also meet write/read cycle time. That is write cycle time should be more than tWC_min and read cycle should be more than tRC_min. Obviously, we do not achieve that now.

This patch corrects the low level time calculation to meet minimum read/write cycle time required. After getting the high hold time, WE# low level time will be promised to meet tWP_min and tWC_min requirement, and RE# low level time will be promised to meet tREA_max, tRP_min and tRC_min requirement.

Fixes edfee3619c49 ("mtd: nand: mtk: add ->setup_data_interface() hook")
---
 drivers/mtd/nand/raw/mtk_nand.c | 24 +++++++++++++++++++++---
 1 file changed, 21 insertions(+), 3 deletions(-)
drivers/mtd/nand/raw/mtk_nand.c +2 -1
index b6b4602f5132..4fbb0c6ecae3 100644
@@ -508,7 +508,8 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
 {
 	struct mtk_nfc *nfc = nand_get_controller_data(chip);
 	const struct nand_sdr_timings *timings;
-	u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst, trlt;
+	u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst = 0, trlt = 0;
+	u32 thold;
 
 	timings = nand_get_sdr_timings(conf);
 	if (IS_ERR(timings))

drivers/mtd/nand/raw/mtk_nand.c static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline, · line 553

Quoted 10 lines
drivers/mtd/nand/raw/mtk_nand.c +6 -1
@@ -544,11 +545,28 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
 	twh = DIV_ROUND_UP(twh * rate, 1000000) - 1;
 	twh &= 0xf;
 
-	twst = timings->tWP_min / 1000;
+	/* Calculate real WE#/RE# hold time in nanosecond */
+	thold = (twh + 1) * 1000000 / rate;
+	/* nanosecond to picosecond */
+	thold *= 1000;
+
+	/**
        /*
Quoted 9 lines
drivers/mtd/nand/raw/mtk_nand.c +6 -0
+	 * WE# low level time should be expaned to meet WE# pulse time
+	 * and WE# cycle time at the same time.
+	 */
+	if (thold < timings->tWC_min)
+		twst = timings->tWC_min - thold;
+	twst = max(timings->tWP_min, twst) / 1000;
 	twst = DIV_ROUND_UP(twst * rate, 1000000) - 1;
 	twst &= 0xf;
 
Quoted 4 lines

drivers/mtd/nand/raw/mtk_nand.c static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline, · line 563

Quoted 2 lines
drivers/mtd/nand/raw/mtk_nand.c +1 -1
-	trlt = max(timings->tREA_max, timings->tRP_min) / 1000;
+	/**

Ditto

OK.

Quoted 13 lines

drivers/mtd/nand/raw/mtk_nand.c static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline, · line 572

Quoted 10 lines
drivers/mtd/nand/raw/mtk_nand.c +6 -0
+	 * RE# low level time should be expaned to meet RE# pulse time,
+	 * RE# access time and RE# cycle time at the same time.
+	 */
+	if (thold < timings->tRC_min)
+		trlt = timings->tRC_min - thold;
+	trlt = max3(trlt, timings->tREA_max, timings->tRP_min) / 1000;
 	trlt = DIV_ROUND_UP(trlt * rate, 1000000) - 1;
 	trlt &= 0xf;
 

With this fixed:

Quoted 5 lines

Thanks,
Miquèl

Thanks,
Xiaolei

author
#7 lore raw

PATCH v2 2/5 mtd: rawnand: mtk: Improve data sampling timing for read cycle

In reply to Xiaolei Li

Currently, we expand RE# low level time by choosing the max value between RE# pulse width and RE# access time, and sample data at the rising edge of RE#.

Then, if RE# access time is bigger than RE# pulse width, the real read cycle time may be more than NAND SPEC required. This makes read performance be worse than that expected.

This patch improves data sampling timing by calculating RE# low level time according to RE# pulse width. If RE# access time is bigger than RE# pulse width, then delay sampling data timing.

The result of contrast test base on MT2712 evaluat board is as follow.

nand: Micron MT29F16G08ADBCAH4
nand: 2048 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224 NFI 2x clock rate: 124800000 HZ.

Read speed without this patch:
mtd_speedtest: page read speed is 14012 KiB/s
mtd_speedtest: 2 page read speed is 14860 KiB/s

Read speed with this patch:
mtd_speedtest: page read speed is 18724 KiB/s
mtd_speedtest: 2 page read speed is 18713 KiB/s

---
 drivers/mtd/nand/raw/mtk_nand.c | 46 ++++++++++++++++++++++++++-------
 1 file changed, 36 insertions(+), 10 deletions(-)
drivers/mtd/nand/raw/mtk_nand.c +36 -10
index 4fbb0c6ecae3..e90c38c6f835 100644
@@ -87,6 +87,10 @@
 #define NFI_FDMM(x)		(0xA4 + (x) * sizeof(u32) * 2)
 #define NFI_FDM_MAX_SIZE	(8)
 #define NFI_FDM_MIN_SIZE	(1)
+#define NFI_DEBUG_CON1		(0x220)
+#define		STROBE_MASK		GENMASK(4, 3)
+#define		STROBE_SHIFT		(3)
+#define		MAX_STROBE_DLY		(3)
 #define NFI_MASTER_STA		(0x224)
 #define		MASTER_STA_MASK		(0x0FFF)
 #define NFI_EMPTY_THRESH	(0x23C)
@@ -509,7 +513,7 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
 	struct mtk_nfc *nfc = nand_get_controller_data(chip);
 	const struct nand_sdr_timings *timings;
 	u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst = 0, trlt = 0;
-	u32 thold;
+	u32 temp, tsel = 0;
 
 	timings = nand_get_sdr_timings(conf);
 	if (IS_ERR(timings))
@@ -546,30 +550,52 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
 	twh &= 0xf;
 
 	/* Calculate real WE#/RE# hold time in nanosecond */
-	thold = (twh + 1) * 1000000 / rate;
+	temp = (twh + 1) * 1000000 / rate;
 	/* nanosecond to picosecond */
-	thold *= 1000;
+	temp *= 1000;
 
 	/**
 	 * WE# low level time should be expaned to meet WE# pulse time
 	 * and WE# cycle time at the same time.
 	 */
-	if (thold < timings->tWC_min)
-		twst = timings->tWC_min - thold;
+	if (temp < timings->tWC_min)
+		twst = timings->tWC_min - temp;
 	twst = max(timings->tWP_min, twst) / 1000;
 	twst = DIV_ROUND_UP(twst * rate, 1000000) - 1;
 	twst &= 0xf;
 
 	/**
-	 * RE# low level time should be expaned to meet RE# pulse time,
-	 * RE# access time and RE# cycle time at the same time.
+	 * RE# low level time should be expaned to meet RE# pulse time
+	 * and RE# cycle time at the same time.
 	 */
-	if (thold < timings->tRC_min)
-		trlt = timings->tRC_min - thold;
-	trlt = max3(trlt, timings->tREA_max, timings->tRP_min) / 1000;
+	if (temp < timings->tRC_min)
+		trlt = timings->tRC_min - temp;
+	trlt = max(trlt, timings->tRP_min) / 1000;
 	trlt = DIV_ROUND_UP(trlt * rate, 1000000) - 1;
 	trlt &= 0xf;
 
+	/**
+	 * Calculate strobe select timing.
+	 * If RE# access time is bigger than RE# pulse time,
+	 * delay sampling data timing.
+	 */
+	temp = (trlt + 1) * 1000000 / rate;
+	/* nanosecond to picosecond */
+	temp *= 1000;
+	if (temp < timings->tREA_max) {
+		tsel = timings->tREA_max / 1000;
+		tsel = DIV_ROUND_UP(tsel * rate, 1000000);
+		tsel -= (trlt + 1);
+		if (tsel > MAX_STROBE_DLY) {
+			trlt += tsel - MAX_STROBE_DLY;
+			tsel = MAX_STROBE_DLY;
+		}
+	}
+	temp = nfi_readl(nfc, NFI_DEBUG_CON1);
+	temp &= ~STROBE_MASK;
+	temp |= tsel << STROBE_SHIFT;
+	nfi_writel(nfc, temp, NFI_DEBUG_CON1);
+
 	/*
 	 * ACCON: access timing control register
 	 * -------------------------------------
Signature · 6 lines
2.18.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

A message that is not in the archive (sent off-list or not yet received): 20190430100250.28083-3-xiaolei.li-NuS5LvNUpcJWk0Htik3J/[email protected]

Reviewed-by
#9 lore raw

Re: [PATCH v2 2/5] mtd: rawnand: mtk: Improve data sampling timing for read cycle

Hi Xiaolei,

Xiaolei Li <[email protected]> wrote on Tue, 30 Apr 2019 18:02:47 +0800:

Quoted 83 lines

Currently, we expand RE# low level time by choosing the max value between RE# pulse width and RE# access time, and sample data at the rising edge of RE#.

Then, if RE# access time is bigger than RE# pulse width, the real read cycle time may be more than NAND SPEC required. This makes read performance be worse than that expected.

This patch improves data sampling timing by calculating RE# low level time according to RE# pulse width. If RE# access time is bigger than RE# pulse width, then delay sampling data timing.

The result of contrast test base on MT2712 evaluat board is as follow.

nand: Micron MT29F16G08ADBCAH4
nand: 2048 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224 NFI 2x clock rate: 124800000 HZ.

Read speed without this patch:
mtd_speedtest: page read speed is 14012 KiB/s
mtd_speedtest: 2 page read speed is 14860 KiB/s

Read speed with this patch:
mtd_speedtest: page read speed is 18724 KiB/s
mtd_speedtest: 2 page read speed is 18713 KiB/s

---
 drivers/mtd/nand/raw/mtk_nand.c | 46 ++++++++++++++++++++++++++-------
 1 file changed, 36 insertions(+), 10 deletions(-)
drivers/mtd/nand/raw/mtk_nand.c +11 -7
index 4fbb0c6ecae3..e90c38c6f835 100644
@@ -87,6 +87,10 @@
 #define NFI_FDMM(x)		(0xA4 + (x) * sizeof(u32) * 2)
 #define NFI_FDM_MAX_SIZE	(8)
 #define NFI_FDM_MIN_SIZE	(1)
+#define NFI_DEBUG_CON1		(0x220)
+#define		STROBE_MASK		GENMASK(4, 3)
+#define		STROBE_SHIFT		(3)
+#define		MAX_STROBE_DLY		(3)
 #define NFI_MASTER_STA		(0x224)
 #define		MASTER_STA_MASK		(0x0FFF)
 #define NFI_EMPTY_THRESH	(0x23C)
@@ -509,7 +513,7 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
 	struct mtk_nfc *nfc = nand_get_controller_data(chip);
 	const struct nand_sdr_timings *timings;
 	u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst = 0, trlt = 0;
-	u32 thold;
+	u32 temp, tsel = 0;
 
 	timings = nand_get_sdr_timings(conf);
 	if (IS_ERR(timings))
@@ -546,30 +550,52 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
 	twh &= 0xf;
 
 	/* Calculate real WE#/RE# hold time in nanosecond */
-	thold = (twh + 1) * 1000000 / rate;
+	temp = (twh + 1) * 1000000 / rate;
 	/* nanosecond to picosecond */
-	thold *= 1000;
+	temp *= 1000;
 
 	/**
 	 * WE# low level time should be expaned to meet WE# pulse time
 	 * and WE# cycle time at the same time.
 	 */
-	if (thold < timings->tWC_min)
-		twst = timings->tWC_min - thold;
+	if (temp < timings->tWC_min)
+		twst = timings->tWC_min - temp;
 	twst = max(timings->tWP_min, twst) / 1000;
 	twst = DIV_ROUND_UP(twst * rate, 1000000) - 1;
 	twst &= 0xf;
 
 	/**
-	 * RE# low level time should be expaned to meet RE# pulse time,
-	 * RE# access time and RE# cycle time at the same time.
+	 * RE# low level time should be expaned to meet RE# pulse time
+	 * and RE# cycle time at the same time.
 	 */

drivers/mtd/nand/raw/mtk_nand.c static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline, · line 577

Quoted 10 lines
drivers/mtd/nand/raw/mtk_nand.c +4 -3
-	if (thold < timings->tRC_min)
-		trlt = timings->tRC_min - thold;
-	trlt = max3(trlt, timings->tREA_max, timings->tRP_min) / 1000;
+	if (temp < timings->tRC_min)
+		trlt = timings->tRC_min - temp;
+	trlt = max(trlt, timings->tRP_min) / 1000;
 	trlt = DIV_ROUND_UP(trlt * rate, 1000000) - 1;
 	trlt &= 0xf;
 
+	/**
        /*

drivers/mtd/nand/raw/mtk_nand.c static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline, · line 582

Quoted 5 lines
drivers/mtd/nand/raw/mtk_nand.c +5 -0
+	 * Calculate strobe select timing.
+	 * If RE# access time is bigger than RE# pulse time,
+	 * delay sampling data timing.
+	 */
+	temp = (trlt + 1) * 1000000 / rate;

You could precise what unit conversion you do here.

Quoted 9 lines
drivers/mtd/nand/raw/mtk_nand.c +9 -0
+	/* nanosecond to picosecond */
+	temp *= 1000;
+	if (temp < timings->tREA_max) {
+		tsel = timings->tREA_max / 1000;
+		tsel = DIV_ROUND_UP(tsel * rate, 1000000);
+		tsel -= (trlt + 1);
+		if (tsel > MAX_STROBE_DLY) {
+			trlt += tsel - MAX_STROBE_DLY;
+			tsel = MAX_STROBE_DLY;

drivers/mtd/nand/raw/mtk_nand.c static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline, · line 601

Quoted 10 lines
drivers/mtd/nand/raw/mtk_nand.c +7 -0
+		}
+	}
+	temp = nfi_readl(nfc, NFI_DEBUG_CON1);
+	temp &= ~STROBE_MASK;
+	temp |= tsel << STROBE_SHIFT;
+	nfi_writel(nfc, temp, NFI_DEBUG_CON1);
+
 	/*
 	 * ACCON: access timing control register
 	 * -------------------------------------

With this:

Thanks,
Miquèl

_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek

author
#10 lore raw

Re: [PATCH v2 2/5] mtd: rawnand: mtk: Improve data sampling timing for read cycle

Quoted 101 lines · Miquel Raynal

Hi Xiaolei,

Xiaolei Li <[email protected]> wrote on Tue, 30 Apr 2019 18:02:47 +0800:

Quoted 83 lines

Currently, we expand RE# low level time by choosing the max value between RE# pulse width and RE# access time, and sample data at the rising edge of RE#.

Then, if RE# access time is bigger than RE# pulse width, the real read cycle time may be more than NAND SPEC required. This makes read performance be worse than that expected.

This patch improves data sampling timing by calculating RE# low level time according to RE# pulse width. If RE# access time is bigger than RE# pulse width, then delay sampling data timing.

The result of contrast test base on MT2712 evaluat board is as follow.

nand: Micron MT29F16G08ADBCAH4
nand: 2048 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224 NFI 2x clock rate: 124800000 HZ.

Read speed without this patch:
mtd_speedtest: page read speed is 14012 KiB/s
mtd_speedtest: 2 page read speed is 14860 KiB/s

Read speed with this patch:
mtd_speedtest: page read speed is 18724 KiB/s
mtd_speedtest: 2 page read speed is 18713 KiB/s

---
 drivers/mtd/nand/raw/mtk_nand.c | 46 ++++++++++++++++++++++++++-------
 1 file changed, 36 insertions(+), 10 deletions(-)
drivers/mtd/nand/raw/mtk_nand.c +11 -7
index 4fbb0c6ecae3..e90c38c6f835 100644
@@ -87,6 +87,10 @@
 #define NFI_FDMM(x)		(0xA4 + (x) * sizeof(u32) * 2)
 #define NFI_FDM_MAX_SIZE	(8)
 #define NFI_FDM_MIN_SIZE	(1)
+#define NFI_DEBUG_CON1		(0x220)
+#define		STROBE_MASK		GENMASK(4, 3)
+#define		STROBE_SHIFT		(3)
+#define		MAX_STROBE_DLY		(3)
 #define NFI_MASTER_STA		(0x224)
 #define		MASTER_STA_MASK		(0x0FFF)
 #define NFI_EMPTY_THRESH	(0x23C)
@@ -509,7 +513,7 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
 	struct mtk_nfc *nfc = nand_get_controller_data(chip);
 	const struct nand_sdr_timings *timings;
 	u32 rate, tpoecs, tprecs, tc2r, tw2r, twh, twst = 0, trlt = 0;
-	u32 thold;
+	u32 temp, tsel = 0;
 
 	timings = nand_get_sdr_timings(conf);
 	if (IS_ERR(timings))
@@ -546,30 +550,52 @@ static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
 	twh &= 0xf;
 
 	/* Calculate real WE#/RE# hold time in nanosecond */
-	thold = (twh + 1) * 1000000 / rate;
+	temp = (twh + 1) * 1000000 / rate;
 	/* nanosecond to picosecond */
-	thold *= 1000;
+	temp *= 1000;
 
 	/**
 	 * WE# low level time should be expaned to meet WE# pulse time
 	 * and WE# cycle time at the same time.
 	 */
-	if (thold < timings->tWC_min)
-		twst = timings->tWC_min - thold;
+	if (temp < timings->tWC_min)
+		twst = timings->tWC_min - temp;
 	twst = max(timings->tWP_min, twst) / 1000;
 	twst = DIV_ROUND_UP(twst * rate, 1000000) - 1;
 	twst &= 0xf;
 
 	/**
-	 * RE# low level time should be expaned to meet RE# pulse time,
-	 * RE# access time and RE# cycle time at the same time.
+	 * RE# low level time should be expaned to meet RE# pulse time
+	 * and RE# cycle time at the same time.
 	 */

drivers/mtd/nand/raw/mtk_nand.c static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline, · line 577

Quoted 10 lines
drivers/mtd/nand/raw/mtk_nand.c +4 -3
-	if (thold < timings->tRC_min)
-		trlt = timings->tRC_min - thold;
-	trlt = max3(trlt, timings->tREA_max, timings->tRP_min) / 1000;
+	if (temp < timings->tRC_min)
+		trlt = timings->tRC_min - temp;
+	trlt = max(trlt, timings->tRP_min) / 1000;
 	trlt = DIV_ROUND_UP(trlt * rate, 1000000) - 1;
 	trlt &= 0xf;
 
+	/**
        /*
Quoted 7 lines

drivers/mtd/nand/raw/mtk_nand.c static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline, · line 582

Quoted 5 lines
drivers/mtd/nand/raw/mtk_nand.c +5 -0
+	 * Calculate strobe select timing.
+	 * If RE# access time is bigger than RE# pulse time,
+	 * delay sampling data timing.
+	 */
+	temp = (trlt + 1) * 1000000 / rate;

You could precise what unit conversion you do here.

OK. Unit here is nanosecond. I will describe it in next patch version.

Quoted 23 lines
Quoted 10 lines
drivers/mtd/nand/raw/mtk_nand.c +9 -0
+	/* nanosecond to picosecond */
+	temp *= 1000;
+	if (temp < timings->tREA_max) {
+		tsel = timings->tREA_max / 1000;
+		tsel = DIV_ROUND_UP(tsel * rate, 1000000);
+		tsel -= (trlt + 1);
+		if (tsel > MAX_STROBE_DLY) {
+			trlt += tsel - MAX_STROBE_DLY;
+			tsel = MAX_STROBE_DLY;

drivers/mtd/nand/raw/mtk_nand.c static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline, · line 601

Quoted 10 lines
drivers/mtd/nand/raw/mtk_nand.c +7 -0
+		}
+	}
+	temp = nfi_readl(nfc, NFI_DEBUG_CON1);
+	temp &= ~STROBE_MASK;
+	temp |= tsel << STROBE_SHIFT;
+	nfi_writel(nfc, temp, NFI_DEBUG_CON1);
+
 	/*
 	 * ACCON: access timing control register
 	 * -------------------------------------

With this:

Quoted 5 lines

Thanks,
Miquèl

Thanks,
Xiaolei

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

A message that is not in the archive (sent off-list or not yet received): 20190430100250.28083-1-xiaolei.li-NuS5LvNUpcJWk0Htik3J/[email protected]

#12 lore raw

PATCH v2 3/5 mtd: rawnand: mtk: Add validity check for CE# pin setting

Currently, we only check how many CE# pins are set in device tree. But it should be necessary to check whether CE# pin setting is duplicated or if CE# pin index exceeds the maximum CE# number that controller supports.

So, add validity check to avoid these invalid settings.

---
 drivers/mtd/nand/raw/mtk_nand.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)
drivers/mtd/nand/raw/mtk_nand.c +13 -0
index e90c38c6f835..23ebd668bbcd 100644
@@ -162,6 +162,8 @@ struct mtk_nfc {
 	struct list_head chips;
 
 	u8 *buffer;
+
+	unsigned long assigned_cs;
 };
 
 /*
@@ -1367,6 +1369,17 @@ static int mtk_nfc_nand_chip_init(struct device *dev, struct mtk_nfc *nfc,
 			dev_err(dev, "reg property failure : %d\n", ret);
 			return ret;
 		}
+
+		if (tmp >= MTK_NAND_MAX_NSELS) {
+			dev_err(dev, "invalid CS: %u\n", tmp);
+			return -EINVAL;
+		}
+
+		if (test_and_set_bit(tmp, &nfc->assigned_cs)) {
+			dev_err(dev, "CS %u already assigned\n", tmp);
+			return -EINVAL;
+		}
+
 		chip->sels[i] = tmp;
 	}
 
Signature · 1 line
2.18.0
#13 lore raw
In reply to a message not in the archive

Hi Xiaolei,

Xiaolei Li <[email protected]> wrote on Tue, 30 Apr 2019 18:02:45 +0800:

Quoted 8 lines

The following patch set mainly contains:
* Fix low level time calculation of read/write cycle to meet tRC_min and tWC_min requirements.
* Refine RE# pulse width calculation and data sampling to improve read performance.
* Add CS validity check.
* Fix oob buffer pointer wrongly setting and empty page threshold setting.

Quoted 5 lines

Changes on v2 relative to:
--------------------

tree : git://git.infradead.org/linux-mtd.git
branch : master

We just switched to a repository hosted on kernel.org:
https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/
nand/next is the branch for this kind of series.

Thanks,
Miquèl

_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek

author
#14 lore raw

Hi Miquel,

Quoted 16 lines · Miquel Raynal

Hi Xiaolei,

Xiaolei Li <[email protected]> wrote on Tue, 30 Apr 2019 18:02:45 +0800:

Quoted 11 lines

The following patch set mainly contains:
* Fix low level time calculation of read/write cycle to meet tRC_min and tWC_min requirements.
* Refine RE# pulse width calculation and data sampling to improve read performance.
* Add CS validity check.
* Fix oob buffer pointer wrongly setting and empty page threshold setting.

Changes on v2 relative to:
--------------------

Quoted 6 lines
Quoted 2 lines

tree : git://git.infradead.org/linux-mtd.git
branch : master

We just switched to a repository hosted on kernel.org:
https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/
nand/next is the branch for this kind of series.

OK. Good.
Thanks for your sharing.

Quoted 3 lines

Thanks,
Miquèl

Thanks,
Xiaolei

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

author
#15 lore raw

PATCH v2 4/5 mtd: rawnand: mtk: Fix wrongly assigned OOB buffer pointer issue

In reply to Xiaolei Li

One main goal of the function mtk_nfc_update_ecc_stats is to check whether sectors are all empty. If they are empty, set these sectors's data buffer and OOB buffer as 0xff.

But now, the sector OOB buffer pointer is wrongly assigned. We always do memset from sector 0.

To fix this issue, pass start sector number to make OOB buffer pointer be properly assigned.

Fixes 1d6b1e464950 ("mtd: mediatek: driver for MTK Smart Device")
---
 drivers/mtd/nand/raw/mtk_nand.c | 21 ++++++++++-----------
 1 file changed, 10 insertions(+), 11 deletions(-)
drivers/mtd/nand/raw/mtk_nand.c +10 -11
index 23ebd668bbcd..48759af5c058 100644
@@ -889,19 +889,21 @@ static int mtk_nfc_write_oob_std(struct nand_chip *chip, int page)
 	return mtk_nfc_write_page_raw(chip, NULL, 1, page);
 }
 
-static int mtk_nfc_update_ecc_stats(struct mtd_info *mtd, u8 *buf, u32 sectors)
+static int mtk_nfc_update_ecc_stats(struct mtd_info *mtd, u8 *buf, u32 start,
+				    u32 sectors)
 {
 	struct nand_chip *chip = mtd_to_nand(mtd);
 	struct mtk_nfc *nfc = nand_get_controller_data(chip);
 	struct mtk_nfc_nand_chip *mtk_nand = to_mtk_nand(chip);
 	struct mtk_ecc_stats stats;
+	u32 reg_size = mtk_nand->fdm.reg_size;
 	int rc, i;
 
 	rc = nfi_readl(nfc, NFI_STA) & STA_EMP_PAGE;
 	if (rc) {
 		memset(buf, 0xff, sectors * chip->ecc.size);
 		for (i = 0; i < sectors; i++)
-			memset(oob_ptr(chip, i), 0xff, mtk_nand->fdm.reg_size);
+			memset(oob_ptr(chip, start + i), 0xff, reg_size);
 		return 0;
 	}
 
@@ -921,7 +923,7 @@ static int mtk_nfc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip,
 	u32 spare = mtk_nand->spare_per_sector;
 	u32 column, sectors, start, end, reg;
 	dma_addr_t addr;
-	int bitflips;
+	int bitflips = 0;
 	size_t len;
 	u8 *buf;
 	int rc;
@@ -988,14 +990,11 @@ static int mtk_nfc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip,
 	if (rc < 0) {
 		dev_err(nfc->dev, "subpage done timeout\n");
 		bitflips = -EIO;
-	} else {
-		bitflips = 0;
-		if (!raw) {
-			rc = mtk_ecc_wait_done(nfc->ecc, ECC_DECODE);
-			bitflips = rc < 0 ? -ETIMEDOUT :
-				mtk_nfc_update_ecc_stats(mtd, buf, sectors);
-			mtk_nfc_read_fdm(chip, start, sectors);
-		}
+	} else if (!raw) {
+		rc = mtk_ecc_wait_done(nfc->ecc, ECC_DECODE);
+		bitflips = rc < 0 ? -ETIMEDOUT :
+			mtk_nfc_update_ecc_stats(mtd, buf, start, sectors);
+		mtk_nfc_read_fdm(chip, start, sectors);
 	}
 
 	dma_unmap_single(nfc->dev, addr, len, DMA_FROM_DEVICE);
Signature · 6 lines
2.18.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
author
#16 lore raw

PATCH v2 5/5 mtd: rawnand: mtk: Setup empty page threshold correctly

In reply to Xiaolei Li

MTK NAND Controller has the ability to check whether read data are mostly 0xff by comparing zero bit count of read data with empty threshold automatically.

But now we never set this threshold and always make it be default value which is 10.

This patch fixes this problem by setting empty threshold as the product of read sector count and ECC strength.

Fixes 1d6b1e464950 ("mtd: mediatek: driver for MTK Smart Device")
---
 drivers/mtd/nand/raw/mtk_nand.c | 9 +++++++++
 1 file changed, 9 insertions(+)
drivers/mtd/nand/raw/mtk_nand.c +9 -0
index 48759af5c058..b56965328771 100644
@@ -94,6 +94,7 @@
 #define NFI_MASTER_STA		(0x224)
 #define		MASTER_STA_MASK		(0x0FFF)
 #define NFI_EMPTY_THRESH	(0x23C)
+#define		EMPTY_THRESH_MASK	GENMASK(7, 0)
 
 #define MTK_NAME		"mtk-nand"
 #define KB(x)			((x) * 1024UL)
@@ -947,6 +948,14 @@ static int mtk_nfc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip,
 		return -EINVAL;
 	}
 
+	/**
+	 * Setup empty threshold as the product of sector count
+	 * and ECC strength
+	 */
+	reg = sectors * chip->ecc.strength;
+	reg = min_t(unsigned int, reg, EMPTY_THRESH_MASK);
+	nfi_writel(nfc, reg, NFI_EMPTY_THRESH);
+
 	reg = nfi_readw(nfc, NFI_CNFG);
 	reg |= CNFG_READ_EN | CNFG_DMA_BURST_EN | CNFG_AHB;
 	if (!raw) {
Signature · 6 lines
2.18.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
maintainer
#17 lore raw

Re: [PATCH v2 5/5] mtd: rawnand: mtk: Setup empty page threshold correctly

Hi Xiaolei,

Xiaolei Li <[email protected]> wrote on Tue, 30 Apr 2019 18:02:50 +0800:

Quoted 9 lines

MTK NAND Controller has the ability to check whether read data are mostly 0xff by comparing zero bit count of read data with empty threshold automatically.

But now we never set this threshold and always make it be default value which is 10.

This patch fixes this problem by setting empty threshold as the product of read sector count and ECC strength.

Are you sure it is not a per-sector value?

Did you use nandbiterrs to validate?

Quoted 20 lines
Fixes 1d6b1e464950 ("mtd: mediatek: driver for MTK Smart Device")
---
 drivers/mtd/nand/raw/mtk_nand.c | 9 +++++++++
 1 file changed, 9 insertions(+)
drivers/mtd/nand/raw/mtk_nand.c +1 -0
index 48759af5c058..b56965328771 100644
@@ -94,6 +94,7 @@
 #define NFI_MASTER_STA		(0x224)
 #define		MASTER_STA_MASK		(0x0FFF)
 #define NFI_EMPTY_THRESH	(0x23C)
+#define		EMPTY_THRESH_MASK	GENMASK(7, 0)
 
 #define MTK_NAME		"mtk-nand"
 #define KB(x)			((x) * 1024UL)

drivers/mtd/nand/raw/mtk_nand.c static int mtk_nfc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, · line 951

Quoted 4 lines
drivers/mtd/nand/raw/mtk_nand.c +1 -0
@@ -947,6 +948,14 @@ static int mtk_nfc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip,
 		return -EINVAL;
 	}
 
+	/**
        /*

drivers/mtd/nand/raw/mtk_nand.c static int mtk_nfc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, · line 961

Quoted 10 lines
drivers/mtd/nand/raw/mtk_nand.c +7 -0
+	 * Setup empty threshold as the product of sector count
+	 * and ECC strength
+	 */
+	reg = sectors * chip->ecc.strength;
+	reg = min_t(unsigned int, reg, EMPTY_THRESH_MASK);
+	nfi_writel(nfc, reg, NFI_EMPTY_THRESH);
+
 	reg = nfi_readw(nfc, NFI_CNFG);
 	reg |= CNFG_READ_EN | CNFG_DMA_BURST_EN | CNFG_AHB;
 	if (!raw) {

Thanks,
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

#18 lore raw

Re: [PATCH v2 5/5] mtd: rawnand: mtk: Setup empty page threshold correctly

Hi Miquel,

Quoted 9 lines · Miquel Raynal

Hi Xiaolei,

Xiaolei Li <[email protected]> wrote on Tue, 30 Apr 2019 18:02:50 +0800:

Quoted 4 lines

MTK NAND Controller has the ability to check whether read data are mostly 0xff by comparing zero bit count of read data with empty threshold automatically.

Quoted 7 lines
Quoted 5 lines

But now we never set this threshold and always make it be default value which is 10.

This patch fixes this problem by setting empty threshold as the product of read sector count and ECC strength.

Are you sure it is not a per-sector value?

Frankly, I also think it should be a per-sector value.

But MTK NAND Controller cannot check 0xff by sector. It counts zero bit through all read data. So, I set the empty threshold as the product of read sector count and ECC strength.

Quoted 2 lines

Did you use nandbiterrs to validate?

Yes. I ever did nandbiterrs test, and it passed.

Quoted 28 lines
Quoted 21 lines
Fixes 1d6b1e464950 ("mtd: mediatek: driver for MTK Smart Device")
---
 drivers/mtd/nand/raw/mtk_nand.c | 9 +++++++++
 1 file changed, 9 insertions(+)
drivers/mtd/nand/raw/mtk_nand.c +1 -0
index 48759af5c058..b56965328771 100644
@@ -94,6 +94,7 @@
 #define NFI_MASTER_STA		(0x224)
 #define		MASTER_STA_MASK		(0x0FFF)
 #define NFI_EMPTY_THRESH	(0x23C)
+#define		EMPTY_THRESH_MASK	GENMASK(7, 0)
 
 #define MTK_NAME		"mtk-nand"
 #define KB(x)			((x) * 1024UL)

drivers/mtd/nand/raw/mtk_nand.c static int mtk_nfc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, · line 951

Quoted 4 lines
drivers/mtd/nand/raw/mtk_nand.c +1 -0
@@ -947,6 +948,14 @@ static int mtk_nfc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip,
 		return -EINVAL;
 	}
 
+	/**
        /*
Quoted 14 lines

drivers/mtd/nand/raw/mtk_nand.c static int mtk_nfc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, · line 961

Quoted 10 lines
drivers/mtd/nand/raw/mtk_nand.c +7 -0
+	 * Setup empty threshold as the product of sector count
+	 * and ECC strength
+	 */
+	reg = sectors * chip->ecc.strength;
+	reg = min_t(unsigned int, reg, EMPTY_THRESH_MASK);
+	nfi_writel(nfc, reg, NFI_EMPTY_THRESH);
+
 	reg = nfi_readw(nfc, NFI_CNFG);
 	reg |= CNFG_READ_EN | CNFG_DMA_BURST_EN | CNFG_AHB;
 	if (!raw) {

Thanks,
Miquèl

Thanks,
Xiaolei

_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek