Skip to contentSkip to conversation

ARM: meson: Add G12A USB Support

PATCH Superseded Neil Armstrong 3 participants 9 messages May 7, 2019 – May 9, 2019

Subsystems (6)
lore
Share & tools
lore
#0 lore raw

v3 cover ARM: meson: Add G12A USB Support

This patchset adds support for USB on Amlogic G12A SoCs.

This patchset is composed with :
- PHY Drivers
- USB Control Glue driver
- G12A board setup for Device mode

Device Tree nodes will be added in a separate patchset when applied on a tagged Linux tree.

The Amlogic G12A USB Complex is composed of :
- 2 USB Controllers :
* DWC3 for USB2 and USB3 Host functionality
* DWC2 for USB2 Peripheral functionality
- 2 USB2 OTG PHYs, only a single one will be routed to either DWC2 to DWC3
- 1 USB3 PHY shared with PCIE funcionnality
- A Glue to control PHY routing, setup and OTG detection

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY.

This drivers supports the on-probe setup of the OTG mode, and manually via a setup function in the G12A common board code.

Changes since v2:
- rebased on u-boot master

Changes since v1:
- switch printf() to debug() in patch 1

Neil Armstrong (3):
usb: dwc3: Add Meson G12A USB Glue
phy: meson: add Amlogic G12A USB2 and USB3+PCIE PHY drivers
mach-meson: g12a: add DWC2 peripheral mode support

 arch/arm/include/asm/arch-meson/usb.h |  12 +
 arch/arm/mach-meson/board-g12a.c      | 126 +++++++
 drivers/phy/Kconfig                   |   8 +
 drivers/phy/Makefile                  |   1 +
 drivers/phy/meson-g12a-usb2.c         | 216 ++++++++++++
 drivers/phy/meson-g12a-usb3-pcie.c    | 345 +++++++++++++++++++
 drivers/usb/dwc3/Kconfig              |   8 +
 drivers/usb/dwc3/Makefile             |   1 +
 drivers/usb/dwc3/dwc3-meson-g12a.c    | 456 ++++++++++++++++++++++++++
 9 files changed, 1173 insertions(+)
 create mode 100644 arch/arm/include/asm/arch-meson/usb.h
 create mode 100644 drivers/phy/meson-g12a-usb2.c
 create mode 100644 drivers/phy/meson-g12a-usb3-pcie.c
 create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c
Signature · 1 line
2.21.0
#1 lore raw

PATCH v3 1/3 usb: dwc3: Add Meson G12A USB Glue

Adds support for Amlogic G12A USB Control Glue HW.

The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only

A glue connects these both controllers to 2 USB2 PHYs, and optionnally to an USB3+PCIE Combo PHY shared with the PCIE controller.

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY.

This driver sets the OTG capable port as Host mode by default, the switch to Device mode is to be done in a separate patch.

---
 drivers/usb/dwc3/Kconfig           |   8 +
 drivers/usb/dwc3/Makefile          |   1 +
 drivers/usb/dwc3/dwc3-meson-g12a.c | 456 +++++++++++++++++++++++++++++
 3 files changed, 465 insertions(+)
 create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c
drivers/usb/dwc3/Kconfig +8 -0
index bbd8105c06..25e1a38aee 100644
@@ -44,6 +44,14 @@ config USB_DWC3_GENERIC
 	  Select this for Xilinx ZynqMP and similar Platforms.
 	  This wrapper supports Host and Peripheral operation modes.
 
+config USB_DWC3_MESON_G12A
+	bool "Amlogic Meson G12A USB wrapper"
+	depends on DM_USB && USB_DWC3 && ARCH_MESON
+	imply PHY
+	help
+	  Select this for Amlogic Meson G12A Platforms.
+	  This wrapper supports Host and Peripheral operation modes.
+
 config USB_DWC3_UNIPHIER
 	bool "DesignWare USB3 Host Support on UniPhier Platforms"
 	depends on ARCH_UNIPHIER && USB_XHCI_DWC3
drivers/usb/dwc3/Makefile +1 -0
index 60b5515a67..0b652a6f36 100644
@@ -7,6 +7,7 @@ dwc3-y					:= core.o
 obj-$(CONFIG_USB_DWC3_GADGET)		+= gadget.o ep0.o
 
 obj-$(CONFIG_USB_DWC3_OMAP)		+= dwc3-omap.o
+obj-$(CONFIG_USB_DWC3_MESON_G12A)	+= dwc3-meson-g12a.o
 obj-$(CONFIG_USB_DWC3_GENERIC)		+= dwc3-generic.o
 obj-$(CONFIG_USB_DWC3_UNIPHIER)		+= dwc3-uniphier.o
 obj-$(CONFIG_USB_DWC3_PHY_OMAP)		+= ti_usb_phy.o
drivers/usb/dwc3/dwc3-meson-g12a.c new file +456 -0

456 lines not on this page · raw message

Signature · 1 line
2.21.0
#2 lore raw

PATCH v3 2/3 phy: meson: add Amlogic G12A USB2 and USB3+PCIE PHY drivers

In reply to Neil Armstrong

This adds support for the USB PHYs found in the Amlogic G12A SoC Family.

The USB2 PHY supports Host and/or Peripheral mode, depending on it's position. The first PHY is only used as Host, but the second supports Dual modes defined by the USB Control Glue HW in front of the USB Controllers.

The second driver supports USB3 Host mode or PCIE 2.0 mode, depending on the layout of the board.
Selection is done by the #phy-cells, making the mode static and exclusive.

---
 drivers/phy/Kconfig                |   8 +
 drivers/phy/Makefile               |   1 +
 drivers/phy/meson-g12a-usb2.c      | 216 ++++++++++++++++++
 drivers/phy/meson-g12a-usb3-pcie.c | 345 +++++++++++++++++++++++++++++
 4 files changed, 570 insertions(+)
 create mode 100644 drivers/phy/meson-g12a-usb2.c
 create mode 100644 drivers/phy/meson-g12a-usb3-pcie.c
drivers/phy/Kconfig +8 -0
index 102fb91fff..957efb3984 100644
@@ -147,6 +147,14 @@ config MESON_GXL_USB_PHY
 	  This is the generic phy driver for the Amlogic Meson GXL
 	  USB2 and USB3 PHYS.
 
+config MESON_G12A_USB_PHY
+	bool "Amlogic Meson G12A USB PHYs"
+	depends on PHY && ARCH_MESON && MESON_G12A
+	imply REGMAP
+	help
+	  This is the generic phy driver for the Amlogic Meson G12A
+	  USB2 and USB3 PHYS.
+
 config MSM8916_USB_PHY
 	bool "Qualcomm MSM8916 USB PHY support"
 	depends on PHY
drivers/phy/Makefile +1 -0
index b55917bce1..90646ca55b 100644
@@ -16,6 +16,7 @@ obj-$(CONFIG_PHY_RCAR_GEN2) += phy-rcar-gen2.o
 obj-$(CONFIG_PHY_RCAR_GEN3) += phy-rcar-gen3.o
 obj-$(CONFIG_PHY_STM32_USBPHYC) += phy-stm32-usbphyc.o
 obj-$(CONFIG_MESON_GXL_USB_PHY) += meson-gxl-usb2.o meson-gxl-usb3.o
+obj-$(CONFIG_MESON_G12A_USB_PHY) += meson-g12a-usb2.o meson-g12a-usb3-pcie.o
 obj-$(CONFIG_MSM8916_USB_PHY) += msm8916-usbh-phy.o
 obj-$(CONFIG_OMAP_USB2_PHY) += omap-usb2-phy.o
 obj-$(CONFIG_KEYSTONE_USB_PHY) += keystone-usb-phy.o
drivers/phy/meson-g12a-usb2.c new file +216 -0

216 lines not on this page · raw message

drivers/phy/meson-g12a-usb3-pcie.c new file +345 -0

345 lines not on this page · raw message

Signature · 1 line
2.21.0
#3 lore raw

PATCH v3 3/3 mach-meson: g12a: add DWC2 peripheral mode support

In reply to Neil Armstrong

Adds support for Amlogic G12A USB Device mode.

The DWC2 Controller behind the Glue can be connected to an OTG capable PHY. The Glue setups the PHY mode.

This patch implements Device mode support by adding a board_usb_init/cleanup setting up the DWC2 controller and switch the OTG capable port to Device before starting the DWC2 controller in Device mode.

---
 arch/arm/include/asm/arch-meson/usb.h |  12 +++
 arch/arm/mach-meson/board-g12a.c      | 126 ++++++++++++++++++++++++++
 2 files changed, 138 insertions(+)
 create mode 100644 arch/arm/include/asm/arch-meson/usb.h
arch/arm/include/asm/arch-meson/usb.h new file +12 -0
new file mode 100644
index 0000000000..b794b5ce77
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <[email protected]>
+ */
+
+#ifndef __MESON_USB_H__
+#define __MESON_USB_H__
+
+int dwc3_meson_g12a_force_mode(struct udevice *dev, enum usb_dr_mode mode);
+
+#endif /* __MESON_USB_H__ */
arch/arm/mach-meson/board-g12a.c +126 -0

136 lines not on this page · raw message

Signature · 1 line
2.21.0
#4 lore raw

v3 cover ARM: meson: Add G12A USB Support

In reply to Neil Armstrong
Quoted 36 lines · Neil Armstrong

This patchset adds support for USB on Amlogic G12A SoCs.

This patchset is composed with :
- PHY Drivers
- USB Control Glue driver
- G12A board setup for Device mode

Device Tree nodes will be added in a separate patchset when applied on a tagged Linux tree.

The Amlogic G12A USB Complex is composed of :
- 2 USB Controllers :
* DWC3 for USB2 and USB3 Host functionality
* DWC2 for USB2 Peripheral functionality
- 2 USB2 OTG PHYs, only a single one will be routed to either DWC2 to DWC3
- 1 USB3 PHY shared with PCIE funcionnality
- A Glue to control PHY routing, setup and OTG detection

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY.

This drivers supports the on-probe setup of the OTG mode, and manually via a setup function in the G12A common board code.

Changes since v2:
- rebased on u-boot master

Changes since v1:
- switch printf() to debug() in patch 1

Neil Armstrong (3):
usb: dwc3: Add Meson G12A USB Glue
phy: meson: add Amlogic G12A USB2 and USB3+PCIE PHY drivers
mach-meson: g12a: add DWC2 peripheral mode support

Quoted 15 lines
 arch/arm/include/asm/arch-meson/usb.h |  12 +
 arch/arm/mach-meson/board-g12a.c      | 126 +++++++
 drivers/phy/Kconfig                   |   8 +
 drivers/phy/Makefile                  |   1 +
 drivers/phy/meson-g12a-usb2.c         | 216 ++++++++++++
 drivers/phy/meson-g12a-usb3-pcie.c    | 345 +++++++++++++++++++
 drivers/usb/dwc3/Kconfig              |   8 +
 drivers/usb/dwc3/Makefile             |   1 +
 drivers/usb/dwc3/dwc3-meson-g12a.c    | 456 ++++++++++++++++++++++++++
 9 files changed, 1173 insertions(+)
 create mode 100644 arch/arm/include/asm/arch-meson/usb.h
 create mode 100644 drivers/phy/meson-g12a-usb2.c
 create mode 100644 drivers/phy/meson-g12a-usb3-pcie.c
 create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c

Looks good to me, pick this via the meson tree please.

Signature · 2 lines
Best regards,
Marek Vasut
#5 lore raw

v3 cover ARM: meson: Add G12A USB Support

Hi Marek,

Quoted 52 lines · Marek Vasut
Quoted 36 lines · Neil Armstrong

This patchset adds support for USB on Amlogic G12A SoCs.

This patchset is composed with :
- PHY Drivers
- USB Control Glue driver
- G12A board setup for Device mode

Device Tree nodes will be added in a separate patchset when applied on a tagged Linux tree.

The Amlogic G12A USB Complex is composed of :
- 2 USB Controllers :
* DWC3 for USB2 and USB3 Host functionality
* DWC2 for USB2 Peripheral functionality
- 2 USB2 OTG PHYs, only a single one will be routed to either DWC2 to DWC3
- 1 USB3 PHY shared with PCIE funcionnality
- A Glue to control PHY routing, setup and OTG detection

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY.

This drivers supports the on-probe setup of the OTG mode, and manually via a setup function in the G12A common board code.

Changes since v2:
- rebased on u-boot master

Changes since v1:
- switch printf() to debug() in patch 1

Neil Armstrong (3):
usb: dwc3: Add Meson G12A USB Glue
phy: meson: add Amlogic G12A USB2 and USB3+PCIE PHY drivers
mach-meson: g12a: add DWC2 peripheral mode support

Quoted 15 lines
 arch/arm/include/asm/arch-meson/usb.h |  12 +
 arch/arm/mach-meson/board-g12a.c      | 126 +++++++
 drivers/phy/Kconfig                   |   8 +
 drivers/phy/Makefile                  |   1 +
 drivers/phy/meson-g12a-usb2.c         | 216 ++++++++++++
 drivers/phy/meson-g12a-usb3-pcie.c    | 345 +++++++++++++++++++
 drivers/usb/dwc3/Kconfig              |   8 +
 drivers/usb/dwc3/Makefile             |   1 +
 drivers/usb/dwc3/dwc3-meson-g12a.c    | 456 ++++++++++++++++++++++++++
 9 files changed, 1173 insertions(+)
 create mode 100644 arch/arm/include/asm/arch-meson/usb.h
 create mode 100644 drivers/phy/meson-g12a-usb2.c
 create mode 100644 drivers/phy/meson-g12a-usb3-pcie.c
 create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c
Quoted 2 lines

Looks good to me, pick this via the meson tree please.

No problem, but Lukasz wanted to pick it up.

Lukasz, I can push it through u-boot-amlogic tree, is it ok for you ?

Thanks,
Neil

#6 lore raw

v3 cover ARM: meson: Add G12A USB Support

Quoted 55 lines · Neil Armstrong

Hi Marek,

Quoted 52 lines · Marek Vasut
Quoted 51 lines · Neil Armstrong

This patchset adds support for USB on Amlogic G12A SoCs.

This patchset is composed with :
- PHY Drivers
- USB Control Glue driver
- G12A board setup for Device mode

Device Tree nodes will be added in a separate patchset when applied on a tagged Linux tree.

The Amlogic G12A USB Complex is composed of :
- 2 USB Controllers :
* DWC3 for USB2 and USB3 Host functionality
* DWC2 for USB2 Peripheral functionality
- 2 USB2 OTG PHYs, only a single one will be routed to either DWC2 to DWC3
- 1 USB3 PHY shared with PCIE funcionnality
- A Glue to control PHY routing, setup and OTG detection

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY.

This drivers supports the on-probe setup of the OTG mode, and manually via a setup function in the G12A common board code.

Changes since v2:
- rebased on u-boot master

Changes since v1:
- switch printf() to debug() in patch 1

Neil Armstrong (3):
usb: dwc3: Add Meson G12A USB Glue
phy: meson: add Amlogic G12A USB2 and USB3+PCIE PHY drivers
mach-meson: g12a: add DWC2 peripheral mode support

 arch/arm/include/asm/arch-meson/usb.h |  12 +
 arch/arm/mach-meson/board-g12a.c      | 126 +++++++
 drivers/phy/Kconfig                   |   8 +
 drivers/phy/Makefile                  |   1 +
 drivers/phy/meson-g12a-usb2.c         | 216 ++++++++++++
 drivers/phy/meson-g12a-usb3-pcie.c    | 345 +++++++++++++++++++
 drivers/usb/dwc3/Kconfig              |   8 +
 drivers/usb/dwc3/Makefile             |   1 +
 drivers/usb/dwc3/dwc3-meson-g12a.c    | 456 ++++++++++++++++++++++++++
 9 files changed, 1173 insertions(+)
 create mode 100644 arch/arm/include/asm/arch-meson/usb.h
 create mode 100644 drivers/phy/meson-g12a-usb2.c
 create mode 100644 drivers/phy/meson-g12a-usb3-pcie.c
 create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c
Quoted 6 lines
Quoted 2 lines

Looks good to me, pick this via the meson tree please.

No problem, but Lukasz wanted to pick it up.

Lukasz, I can push it through u-boot-amlogic tree, is it ok for you ?

I don't care either way, whatever is comfortable for you two.

Signature · 2 lines
Best regards,
Marek Vasut
#7 lore raw

v3 cover ARM: meson: Add G12A USB Support

Quoted 61 lines · On Tue, 7 May 2019 17:16:52 +0200 Marek Vasut <[email protected]> wrote:
Quoted 60 lines · Neil Armstrong

Hi Marek,

Quoted 56 lines · Marek Vasut
Quoted 38 lines · Neil Armstrong

This patchset adds support for USB on Amlogic G12A SoCs.

This patchset is composed with :
- PHY Drivers
- USB Control Glue driver
- G12A board setup for Device mode

Device Tree nodes will be added in a separate patchset when applied on a tagged Linux tree.

The Amlogic G12A USB Complex is composed of :
- 2 USB Controllers :
* DWC3 for USB2 and USB3 Host functionality
* DWC2 for USB2 Peripheral functionality
- 2 USB2 OTG PHYs, only a single one will be routed to either DWC2 to DWC3
- 1 USB3 PHY shared with PCIE funcionnality
- A Glue to control PHY routing, setup and OTG detection

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY.

This drivers supports the on-probe setup of the OTG mode, and manually via a setup function in the G12A common board code.

Changes since v2:
- rebased on u-boot master

Changes since v1:
- switch printf() to debug() in patch 1

Neil Armstrong (3):
usb: dwc3: Add Meson G12A USB Glue
phy: meson: add Amlogic G12A USB2 and USB3+PCIE PHY drivers
mach-meson: g12a: add DWC2 peripheral mode support

Quoted 15 lines
 arch/arm/include/asm/arch-meson/usb.h |  12 +
 arch/arm/mach-meson/board-g12a.c      | 126 +++++++
 drivers/phy/Kconfig                   |   8 +
 drivers/phy/Makefile                  |   1 +
 drivers/phy/meson-g12a-usb2.c         | 216 ++++++++++++
 drivers/phy/meson-g12a-usb3-pcie.c    | 345 +++++++++++++++++++
 drivers/usb/dwc3/Kconfig              |   8 +
 drivers/usb/dwc3/Makefile             |   1 +
 drivers/usb/dwc3/dwc3-meson-g12a.c    | 456
++++++++++++++++++++++++++ 9 files changed, 1173 insertions(+)
 create mode 100644 arch/arm/include/asm/arch-meson/usb.h
 create mode 100644 drivers/phy/meson-g12a-usb2.c
 create mode 100644 drivers/phy/meson-g12a-usb3-pcie.c
 create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c

Looks good to me, pick this via the meson tree please.

Quoted 7 lines
Quoted 4 lines

No problem, but Lukasz wanted to pick it up.

Lukasz, I can push it through u-boot-amlogic tree, is it ok for you ?

I don't care either way, whatever is comfortable for you two.

Yes, please - use the u-boot-amlogic tree. Thanks in advance.

Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de -------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190507/1e2c1d9a/attachment.sig>

#8 lore raw

v3 cover ARM: meson: Add G12A USB Support

Lukasz, Marek,

Quoted 66 lines · Lukasz Majewski
Quoted 63 lines · On Tue, 7 May 2019 17:16:52 +0200 Marek Vasut <[email protected]> wrote:
Quoted 62 lines · Neil Armstrong

Hi Marek,

Quoted 54 lines · Marek Vasut
Quoted 38 lines · Neil Armstrong

This patchset adds support for USB on Amlogic G12A SoCs.

This patchset is composed with :
- PHY Drivers
- USB Control Glue driver
- G12A board setup for Device mode

Device Tree nodes will be added in a separate patchset when applied on a tagged Linux tree.

The Amlogic G12A USB Complex is composed of :
- 2 USB Controllers :
* DWC3 for USB2 and USB3 Host functionality
* DWC2 for USB2 Peripheral functionality
- 2 USB2 OTG PHYs, only a single one will be routed to either DWC2 to DWC3
- 1 USB3 PHY shared with PCIE funcionnality
- A Glue to control PHY routing, setup and OTG detection

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including routing of the OTG PHY between the DWC3 and DWC2 controllers, and setups the on-chip OTG mode selection for this PHY.

This drivers supports the on-probe setup of the OTG mode, and manually via a setup function in the G12A common board code.

Changes since v2:
- rebased on u-boot master

Changes since v1:
- switch printf() to debug() in patch 1

Neil Armstrong (3):
usb: dwc3: Add Meson G12A USB Glue
phy: meson: add Amlogic G12A USB2 and USB3+PCIE PHY drivers
mach-meson: g12a: add DWC2 peripheral mode support

Quoted 15 lines
 arch/arm/include/asm/arch-meson/usb.h |  12 +
 arch/arm/mach-meson/board-g12a.c      | 126 +++++++
 drivers/phy/Kconfig                   |   8 +
 drivers/phy/Makefile                  |   1 +
 drivers/phy/meson-g12a-usb2.c         | 216 ++++++++++++
 drivers/phy/meson-g12a-usb3-pcie.c    | 345 +++++++++++++++++++
 drivers/usb/dwc3/Kconfig              |   8 +
 drivers/usb/dwc3/Makefile             |   1 +
 drivers/usb/dwc3/dwc3-meson-g12a.c    | 456
++++++++++++++++++++++++++ 9 files changed, 1173 insertions(+)
 create mode 100644 arch/arm/include/asm/arch-meson/usb.h
 create mode 100644 drivers/phy/meson-g12a-usb2.c
 create mode 100644 drivers/phy/meson-g12a-usb3-pcie.c
 create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c
Quoted 2 lines

Looks good to me, pick this via the meson tree please.

No problem, but Lukasz wanted to pick it up.

Quoted 7 lines
Quoted 5 lines
Quoted 2 lines

Lukasz, I can push it through u-boot-amlogic tree, is it ok for you ?

I don't care either way, whatever is comfortable for you two.

Yes, please - use the u-boot-amlogic tree. Thanks in advance.

Done, thanks.

Neil

Quoted 4 lines

Best regards,

Quoted 8 lines

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190509/422f5401/attachment.sig>