spi: Add Atmel QuadSPI driver
Subsystems (3)
cover spi: Add Atmel QuadSPI driver
From: Tudor Ambarus <[email protected]>
Backport the driver from linux v5.1-rc5 and adapt it for u-boot. Tested on sama5d2_xplained Rev B with mx25l25635e spi-nor flash.
=> sf probe 1:0
SF: Detected mx25l25635e with page size 256 Bytes, erase size 64 KiB, total 32 MiB => sf erase 0 100000
SF: 1048576 bytes @ 0x0 Erased: OK
=> mw.b 0x21000000 bc 100000
=> sf write 0x21000000 0 100000
device 0 offset 0x0, size 0x100000
SF: 1048576 bytes @ 0x0 Written: OK
=> sf read 0x21100000 0 100000
device 0 offset 0x0, size 0x100000
SF: 1048576 bytes @ 0x0 Read: OK
=> cmp.b 0x21000000 0x21100000 100000
Total of 1048576 byte(s) were the same
Tudor Ambarus (5):
dt-bindings: spi: add bindings for Atmel QSPI driver
spi: Add Atmel QuadSPI driver
configs: sama5d2_xplained: enable SST and MACRONIX flashes
ARM: dts: at91: sama5d2_xplained: use jedec,spi-nor compatible
ARM: dts: at91: sama5d2_xplained: describe flash bus width
arch/arm/dts/at91-sama5d2_xplained.dts | 4 +- configs/sama5d2_xplained_mmc_defconfig | 2 + doc/device-tree-bindings/spi/atmel-quadspi.txt | 37 ++ drivers/spi/Kconfig | 7 + drivers/spi/Makefile | 1 + drivers/spi/atmel-quadspi.c | 535 +++++++++++++++++++++++++ 6 files changed, 585 insertions(+), 1 deletion(-) create mode 100644 doc/device-tree-bindings/spi/atmel-quadspi.txt create mode 100644 drivers/spi/atmel-quadspi.c
Signature · 1 line
2.9.5
PATCH 1/5 dt-bindings: spi: add bindings for Atmel QSPI driver
From: Tudor Ambarus <[email protected]>
Describe the DT bindings for the driver of the Atmel QSPI controller. Taken form linux v5.1-rc5.
--- doc/device-tree-bindings/spi/atmel-quadspi.txt | 37 ++++++++++++++++++++++++++ 1 file changed, 37 insertions(+) create mode 100644 doc/device-tree-bindings/spi/atmel-quadspi.txt
doc/device-tree-bindings/spi/atmel-quadspi.txt new file +37 -0
@@ -0,0 +1,37 @@ +* Atmel Quad Serial Peripheral Interface (QSPI) + +Required properties: +- compatible: Should be one of the following: + - "atmel,sama5d2-qspi" + - "microchip,sam9x60-qspi" +- reg: Should contain the locations and lengths of the base registers + and the mapped memory. +- reg-names: Should contain the resource reg names: + - qspi_base: configuration register address space + - qspi_mmap: memory mapped address space +- interrupts: Should contain the interrupt for the device. +- clocks: Should reference the peripheral clock and the QSPI system + clock if available. +- clock-names: Should contain "pclk" for the peripheral clock and "qspick" + for the system clock when available. +- #address-cells: Should be <1>. +- #size-cells: Should be <0>. + +Example: + +spi at f0020000 { + compatible = "atmel,sama5d2-qspi"; + reg = <0xf0020000 0x100>, <0xd0000000 0x8000000>; + reg-names = "qspi_base", "qspi_mmap"; + interrupts = <52 IRQ_TYPE_LEVEL_HIGH 7>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 52>; + clock-names = "pclk"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi0_default>; + + m25p80 at 0 { + ... + }; +};
Signature · 1 line
2.9.5
PATCH 2/5 spi: Add Atmel QuadSPI driver
In reply to Tudor.Ambarus at microchip.comFrom: Tudor Ambarus <[email protected]>
Backport the driver from linux v5.1-rc5 and adapt it for u-boot. Tested on sama5d2_xplained Rev B with mx25l25635e spi-nor flash.
--- drivers/spi/Kconfig | 7 + drivers/spi/Makefile | 1 + drivers/spi/atmel-quadspi.c | 535 ++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 543 insertions(+) create mode 100644 drivers/spi/atmel-quadspi.c
drivers/spi/Kconfig +7 -0
@@ -49,6 +49,13 @@ config ATH79_SPI uses driver model and requires a device tree binding to operate. please refer to doc/device-tree-bindings/spi/spi-ath79.txt. +config ATMEL_QSPI + bool "Atmel QSPI driver" + depends on ARCH_AT91 + help + Enable the Ateml Quad-SPI (QSPI) driver. This driver can only be + used to access SPI NOR flashes. + config ATMEL_SPI bool "Atmel SPI driver" default y if ARCH_AT91
drivers/spi/Makefile +1 -0
@@ -18,6 +18,7 @@ endif obj-$(CONFIG_ALTERA_SPI) += altera_spi.o obj-$(CONFIG_ATH79_SPI) += ath79_spi.o +obj-$(CONFIG_ATMEL_QSPI) += atmel-quadspi.o obj-$(CONFIG_ATMEL_SPI) += atmel_spi.o obj-$(CONFIG_BCM63XX_HSSPI) += bcm63xx_hsspi.o obj-$(CONFIG_BCM63XX_SPI) += bcm63xx_spi.o
drivers/spi/atmel-quadspi.c new file +535 -0
535 lines not on this page · raw message
Signature · 1 line
2.9.5
PATCH 3/5 configs: sama5d2_xplained: enable SST and MACRONIX flashes
In reply to Tudor.Ambarus at microchip.comFrom: Tudor Ambarus <[email protected]>
We have a macronix spi-nor flash on sama5d2_xplained RevB and a sst spi-nor flash on RevC.
--- configs/sama5d2_xplained_mmc_defconfig | 2 ++ 1 file changed, 2 insertions(+)
configs/sama5d2_xplained_mmc_defconfig +2 -0
@@ -67,6 +67,8 @@ CONFIG_DM_SPI_FLASH=y CONFIG_SPI_FLASH=y CONFIG_SF_DEFAULT_SPEED=30000000 CONFIG_SPI_FLASH_ATMEL=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SST=y CONFIG_DM_ETH=y CONFIG_MACB=y CONFIG_PINCTRL=y
Signature · 1 line
2.9.5
PATCH 4/5 ARM: dts: at91: sama5d2_xplained: use jedec, spi-nor compatible
In reply to Tudor.Ambarus at microchip.comFrom: Tudor Ambarus <[email protected]>
The flashes present on sama5d2_xplained, mx25l25635e and sst26vf064b, are jedec compatible. Use "jedec,spi-nor" binding.
--- arch/arm/dts/at91-sama5d2_xplained.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/dts/at91-sama5d2_xplained.dts +1 -1
@@ -82,7 +82,7 @@ status = "okay"; flash at 0 { - compatible = "atmel,sama5d2-qspi-flash"; + compatible = "jedec,spi-nor"; reg = <0>; #address-cells = <1>; #size-cells = <1>;
Signature · 1 line
2.9.5
PATCH 5/5 ARM: dts: at91: sama5d2_xplained: describe flash bus width
In reply to Tudor.Ambarus at microchip.comFrom: Tudor Ambarus <[email protected]>
sama5d2_xplained advertises quad capable flashes.
Set bus with to 4.
--- arch/arm/dts/at91-sama5d2_xplained.dts | 2 ++ 1 file changed, 2 insertions(+)
arch/arm/dts/at91-sama5d2_xplained.dts +2 -0
@@ -89,6 +89,8 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_qspi0_default>; spi-max-frequency = <83000000>; + spi-rx-bus-width = <4>; + spi-tx-bus-width = <4>; partition at 00000000 { label = "boot";
Signature · 1 line
2.9.5