configs: sama5d2_ptc_ek: fix NAND PMECC_CAP
PATCH 1/1 configs: sama5d2_ptc_ek: fix NAND PMECC_CAP
From: Tudor Ambarus <[email protected]>
CONFIG_PMECC_CAP has a higher priority than its ONFI detected parameter and will overwrite it when defined. As per commit 49ad40298cc5, CONFIG_PMECC_CAP has a default value of 2 if not otherwise stated. This results in the overwriting of the ONFI ECC bits value. The following errors are seen when booting the kernel from the nand flash:
Loading Environment from NAND... PMECC: Too many errors
NAND read from offset 140000 failed -74
*** Warning - some problems detected reading environment; recovered successfully *** Warning - bad CRC, using default environment
In: serial Out: serial Err: serial Net: eth0: ethernet at f8008000 Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x180000, size 0x80000
PMECC: Too many errors
NAND read from offset 180000 failed -74
0 bytes read: ERROR
NAND read: device 0 offset 0x200000, size 0x600000
PMECC: Too many errors
NAND read from offset 200000 failed -74
0 bytes read: ERROR
Bad Linux ARM zImage magic!
Fix it by setting the right value for ECC bits.
--- configs/sama5d2_ptc_ek_mmc_defconfig | 1 + configs/sama5d2_ptc_ek_nandflash_defconfig | 1 + 2 files changed, 2 insertions(+)
configs/sama5d2_ptc_ek_mmc_defconfig +1 -0
@@ -51,6 +51,7 @@ CONFIG_MMC_SDHCI_ATMEL=y CONFIG_NAND=y CONFIG_NAND_ATMEL=y CONFIG_ATMEL_NAND_HW_PMECC=y +CONFIG_PMECC_CAP=4 CONFIG_DM_ETH=y CONFIG_MACB=y CONFIG_PINCTRL=y
configs/sama5d2_ptc_ek_nandflash_defconfig +1 -0
@@ -50,6 +50,7 @@ CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ATMEL=y CONFIG_NAND_ATMEL=y CONFIG_ATMEL_NAND_HW_PMECC=y +CONFIG_PMECC_CAP=4 CONFIG_DM_ETH=y CONFIG_MACB=y CONFIG_PINCTRL=y
Signature · 1 line
2.9.5
PATCH 1/1 configs: sama5d2_ptc_ek: fix NAND PMECC_CAP
Quoted 31 lines · On 15.05.2019 12:12, Tudor Ambarus - M18064 wrote:
From: Tudor Ambarus <[email protected]>
CONFIG_PMECC_CAPhas a higher priority than its ONFI detected parameter and will overwrite it when defined. As per commit49ad40298cc5,CONFIG_PMECC_CAPhas a default value of 2 if not otherwise stated. This results in the overwriting of the ONFI ECC bits value. The following errors are seen when booting the kernel from the nand flash:Loading Environment from NAND... PMECC: Too many errors
NAND read from offset 140000 failed -74
*** Warning - some problems detected reading environment; recovered successfully *** Warning - bad CRC, using default environmentIn: serial Out: serial Err: serial Net: eth0: ethernet at f8008000 Hit any key to stop autoboot: 0NAND read: device 0 offset
0x180000, size0x80000
PMECC: Too many errors
NAND read from offset 180000 failed -74
0 bytes read: ERRORNAND read: device 0 offset
0x200000, size0x600000
PMECC: Too many errors
NAND read from offset 200000 failed -74
0 bytes read: ERROR
Bad Linux ARM zImage magic!
Quoted 4 lines
Fix it by setting the right value for ECC bits.
Fixes 49ad40298cc5 ("ARM: at91: Convert SPL_GENERATE_ATMEL_PMECC_HEADER to Kconfig")Signed-off-by Tudor Ambarus <[email protected]>
Applied to u-boot-atmel/master, thanks !