Skip to contentSkip to conversation

sysreset: switch to using SYSRESET_POWER_OFF for poweroff

PATCH New Urja Rannikko 5 participants 10 messages May 16, 2019 – Aug 15, 2019

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/3 sysreset: switch to using SYSRESET_POWER_OFF for poweroff

It seems that SYSRESET_POWER_OFF was added recently, and all previous code used SYSRESET_POWER for poweroff. SYSRESET_POWER is supposed to be a PMIC-level power cycle, not a poweroff.

---
v2: Do not change STPMIC1 driver (thats actually SYSRESET_POWER)

Note: I didnt touch the test/dm/sysreset.c code yet, mostly because I wanted to get feedback on this first and that i'd need to understand the tests properly to do that (and i havent used them before at all).

---
 arch/arm/mach-stm32mp/cmd_poweroff.c | 2 +-
 arch/sandbox/cpu/state.c             | 2 +-
 drivers/sysreset/sysreset_psci.c     | 2 +-
 drivers/sysreset/sysreset_sandbox.c  | 4 ++--
 4 files changed, 5 insertions(+), 5 deletions(-)
arch/arm/mach-stm32mp/cmd_poweroff.c +1 -1
index f54dd1daf2..62347425a0 100644
@@ -14,7 +14,7 @@ int do_poweroff(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 	puts("poweroff ...\n");
 	mdelay(100);
 
-	ret = sysreset_walk(SYSRESET_POWER);
+	ret = sysreset_walk(SYSRESET_POWER_OFF);
 
 	if (ret == -EINPROGRESS)
 		mdelay(1000);
arch/sandbox/cpu/state.c +1 -1
index d3b9c05985..dee5fde4f7 100644
@@ -355,7 +355,7 @@ void state_reset_for_test(struct sandbox_state *state)
 {
 	/* No reset yet, so mark it as such. Always allow power reset */
 	state->last_sysreset = SYSRESET_COUNT;
-	state->sysreset_allowed[SYSRESET_POWER] = true;
+	state->sysreset_allowed[SYSRESET_POWER_OFF] = true;
 
 	memset(&state->wdt, '\0', sizeof(state->wdt));
 	memset(state->spi, '\0', sizeof(state->spi));
drivers/sysreset/sysreset_psci.c +1 -1
index de2ec8aeb1..c7907b3226 100644
@@ -18,7 +18,7 @@ static int psci_sysreset_request(struct udevice *dev, enum sysreset_t type)
 	case SYSRESET_COLD:
 		function_id = PSCI_0_2_FN_SYSTEM_RESET;
 		break;
-	case SYSRESET_POWER:
+	case SYSRESET_POWER_OFF:
 		function_id = PSCI_0_2_FN_SYSTEM_OFF;
 		break;
 	default:
drivers/sysreset/sysreset_sandbox.c +2 -2
index 38e2a7e241..8bc9f4b4cc 100644
@@ -57,13 +57,13 @@ static int sandbox_sysreset_request(struct udevice *dev, enum sysreset_t type)
 	case SYSRESET_COLD:
 		state->last_sysreset = type;
 		break;
-	case SYSRESET_POWER:
+	case SYSRESET_POWER_OFF:
 		state->last_sysreset = type;
 		if (!state->sysreset_allowed[type])
 			return -EACCES;
 		sandbox_exit();
 		break;
-	case SYSRESET_POWER_OFF:
+	case SYSRESET_POWER:
 		if (!state->sysreset_allowed[type])
 			return -EACCES;
 	default:
Signature · 1 line
2.21.0
#1 lore raw

PATCH v2 2/3 sysreset: move stm32mp sysreset poweroff implementation to sysreset uclass

This is a generic implementation. Add CONFIG_SYSRESET_CMD_POWEROFF to signal when we need it. Enable it from the STPMIC1 config and in sandbox.

The config flag is transitionary, that is it can be removed after all poweroff implementations use sysreset, and just have CMD_POWEROFF depend on sysreset.

---
v2: Fixup STPMIC1 config selection of CONFIG_SYSRESET_CMD_POWEROFF

---
 arch/Kconfig                         |  1 +
 arch/arm/mach-stm32mp/Makefile       |  3 ---
 arch/arm/mach-stm32mp/cmd_poweroff.c | 24 ------------------------
 drivers/power/pmic/Kconfig           |  1 +
 drivers/sysreset/Kconfig             | 10 ++++++++++
 drivers/sysreset/sysreset-uclass.c   | 18 ++++++++++++++++++
 6 files changed, 30 insertions(+), 27 deletions(-)
 delete mode 100644 arch/arm/mach-stm32mp/cmd_poweroff.c
arch/Kconfig +1 -0
index 239289b885..83ff21dfd7 100644
@@ -91,6 +91,7 @@ config SANDBOX
 	select LZO
 	select SPI
 	select SUPPORT_OF_CONTROL
+	select SYSRESET_CMD_POWEROFF if CMD_POWEROFF
 	imply BITREVERSE
 	select BLOBLIST
 	imply CMD_DM
arch/arm/mach-stm32mp/Makefile +0 -3
index 1493914a11..f59ced5ee1 100644
@@ -11,9 +11,6 @@ ifdef CONFIG_SPL_BUILD
 obj-y += spl.o
 else
 obj-y += bsec.o
-ifndef CONFIG_STM32MP1_TRUSTED
-obj-$(CONFIG_SYSRESET) += cmd_poweroff.o
-endif
 endif
 obj-$(CONFIG_ARMV7_PSCI) += psci.o
 obj-$(CONFIG_$(SPL_)DM_REGULATOR) += pwr_regulator.o
arch/arm/mach-stm32mp/cmd_poweroff.c deleted +0 -24
deleted file mode 100644
index 62347425a0..0000000000
@@ -1,24 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
-/*
- * Copyright (C) 2019, STMicroelectronics - All Rights Reserved
- */
-
-#include <common.h>
-#include <command.h>
-#include <sysreset.h>
-
-int do_poweroff(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-	int ret;
-
-	puts("poweroff ...\n");
-	mdelay(100);
-
-	ret = sysreset_walk(SYSRESET_POWER_OFF);
-
-	if (ret == -EINPROGRESS)
-		mdelay(1000);
-
-	/*NOTREACHED when power off*/
-	return CMD_RET_FAILURE;
-}
drivers/power/pmic/Kconfig +1 -0
index b0cd260354..52edb29b48 100644
@@ -234,6 +234,7 @@ config DM_PMIC_TPS65910
 config PMIC_STPMIC1
 	bool "Enable support for STMicroelectronics STPMIC1 PMIC"
 	depends on DM_PMIC && DM_I2C
+	select SYSRESET_CMD_POWEROFF if CMD_POWEROFF && !ARM_PSCI_FW
 	---help---
 	The STPMIC1 PMIC provides 4 BUCKs, 6 LDOs, 1 VREF and 2 power switches.
 	It is accessed via an I2C interface. The device is used with STM32MP1
drivers/sysreset/Kconfig +10 -0
index 30aed2c4c1..4c883923bf 100644
@@ -33,6 +33,16 @@ config TPL_SYSRESET
 
 if SYSRESET
 
+if CMD_POWEROFF
+
+config SYSRESET_CMD_POWEROFF
+	bool "sysreset implementation of the poweroff command"
+	help
+	  This should be selected by the appropriate PMIC driver if
+	  the poweroff command is enabled.
+
+endif
+
 config SYSRESET_GPIO
 	bool "Enable support for GPIO reset driver"
 	select DM_GPIO
drivers/sysreset/sysreset-uclass.c +18 -0
index ad831c703a..39202588ae 100644
@@ -118,6 +118,24 @@ int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 	return 0;
 }
 
+#if IS_ENABLED(CONFIG_SYSRESET_CMD_POWEROFF)
+int do_poweroff(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+	int ret;
+
+	puts("poweroff ...\n");
+	mdelay(100);
+
+	ret = sysreset_walk(SYSRESET_POWER_OFF);
+
+	if (ret == -EINPROGRESS)
+		mdelay(1000);
+
+	/*NOTREACHED when power off*/
+	return CMD_RET_FAILURE;
+}
+#endif
+
 static int sysreset_post_bind(struct udevice *dev)
 {
 #if defined(CONFIG_NEEDS_MANUAL_RELOC)
Signature · 1 line
2.21.0
#2 lore raw

PATCH v2 2/3 sysreset: move stm32mp sysreset poweroff implementation to sysreset uclass

Hi Urja

Quoted 130 lines · Urja Rannikko

This is a generic implementation. Add CONFIG_SYSRESET_CMD_POWEROFF to signal when we need it. Enable it from the STPMIC1 config and in sandbox.

The config flag is transitionary, that is it can be removed after all poweroff implementations use sysreset, and just have CMD_POWEROFF depend on sysreset.

---
v2: Fixup STPMIC1 config selection of CONFIG_SYSRESET_CMD_POWEROFF

---
 arch/Kconfig                         |  1 +
 arch/arm/mach-stm32mp/Makefile       |  3 ---
 arch/arm/mach-stm32mp/cmd_poweroff.c | 24 ------------------------
 drivers/power/pmic/Kconfig           |  1 +
 drivers/sysreset/Kconfig             | 10 ++++++++++
 drivers/sysreset/sysreset-uclass.c   | 18 ++++++++++++++++++
 6 files changed, 30 insertions(+), 27 deletions(-)
 delete mode 100644 arch/arm/mach-stm32mp/cmd_poweroff.c
arch/Kconfig +1 -0
index 239289b885..83ff21dfd7 100644
@@ -91,6 +91,7 @@ config SANDBOX
 	select LZO
 	select SPI
 	select SUPPORT_OF_CONTROL
+	select SYSRESET_CMD_POWEROFF if CMD_POWEROFF
 	imply BITREVERSE
 	select BLOBLIST
 	imply CMD_DM
arch/arm/mach-stm32mp/Makefile +0 -3
index 1493914a11..f59ced5ee1 100644
@@ -11,9 +11,6 @@ ifdef CONFIG_SPL_BUILD
 obj-y += spl.o
 else
 obj-y += bsec.o
-ifndef CONFIG_STM32MP1_TRUSTED
-obj-$(CONFIG_SYSRESET) += cmd_poweroff.o
-endif
 endif
 obj-$(CONFIG_ARMV7_PSCI) += psci.o
 obj-$(CONFIG_$(SPL_)DM_REGULATOR) += pwr_regulator.o
arch/arm/mach-stm32mp/cmd_poweroff.c deleted +0 -24
deleted file mode 100644
index 62347425a0..0000000000
@@ -1,24 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
-/*
- * Copyright (C) 2019, STMicroelectronics - All Rights Reserved
- */
-
-#include <common.h>
-#include <command.h>
-#include <sysreset.h>
-
-int do_poweroff(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-	int ret;
-
-	puts("poweroff ...\n");
-	mdelay(100);
-
-	ret = sysreset_walk(SYSRESET_POWER_OFF);
-
-	if (ret == -EINPROGRESS)
-		mdelay(1000);
-
-	/*NOTREACHED when power off*/
-	return CMD_RET_FAILURE;
-}
drivers/power/pmic/Kconfig +1 -0
index b0cd260354..52edb29b48 100644
@@ -234,6 +234,7 @@ config DM_PMIC_TPS65910
 config PMIC_STPMIC1
 	bool "Enable support for STMicroelectronics STPMIC1 PMIC"
 	depends on DM_PMIC && DM_I2C
+	select SYSRESET_CMD_POWEROFF if CMD_POWEROFF && !ARM_PSCI_FW
 	---help---
 	The STPMIC1 PMIC provides 4 BUCKs, 6 LDOs, 1 VREF and 2 power switches.
 	It is accessed via an I2C interface. The device is used with STM32MP1
drivers/sysreset/Kconfig +10 -0
index 30aed2c4c1..4c883923bf 100644
@@ -33,6 +33,16 @@ config TPL_SYSRESET
 
 if SYSRESET
 
+if CMD_POWEROFF
+
+config SYSRESET_CMD_POWEROFF
+	bool "sysreset implementation of the poweroff command"
+	help
+	  This should be selected by the appropriate PMIC driver if
+	  the poweroff command is enabled.
+
+endif
+
 config SYSRESET_GPIO
 	bool "Enable support for GPIO reset driver"
 	select DM_GPIO
drivers/sysreset/sysreset-uclass.c +11 -0
index ad831c703a..39202588ae 100644
@@ -118,6 +118,24 @@ int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 	return 0;
 }
 
+#if IS_ENABLED(CONFIG_SYSRESET_CMD_POWEROFF)
+int do_poweroff(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+	int ret;
+
+	puts("poweroff ...\n");
+	mdelay(100);
+
+	ret = sysreset_walk(SYSRESET_POWER_OFF);
+
+	if (ret == -EINPROGRESS)

drivers/sysreset/sysreset-uclass.c int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) · line 141

Quoted 10 lines
drivers/sysreset/sysreset-uclass.c +7 -0
+		mdelay(1000);
+
+	/*NOTREACHED when power off*/
+	return CMD_RET_FAILURE;
+}
+#endif
+
 static int sysreset_post_bind(struct udevice *dev)
 {
 #if defined(CONFIG_NEEDS_MANUAL_RELOC)

Thanks

#3 lore raw

PATCH v2 2/3 sysreset: move stm32mp sysreset poweroff implementation to sysreset uclass

In reply to Urja Rannikko

Hi Urja,

Quoted 9 lines

This is a generic implementation. Add CONFIG_SYSRESET_CMD_POWEROFF to signal when we need it. Enable it from the STPMIC1 config and in sandbox.

The config flag is transitionary, that is it can be removed after all poweroff implementations use sysreset, and just have CMD_POWEROFF depend on sysreset.

Tested on stm32mp1-ev1 with 2 other corrections:
[U-Boot] pmic: stpmic1: add support for SYSRESET_POWER_OFF

	http://patchwork.ozlabs.org/patch/1101856/

[U-Boot] sysreset: syscon: add support for power off

	http://patchwork.ozlabs.org/patch/1101905/
Quoted 127 lines

---
v2: Fixup STPMIC1 config selection of CONFIG_SYSRESET_CMD_POWEROFF

---
 arch/Kconfig                         |  1 +
 arch/arm/mach-stm32mp/Makefile       |  3 ---
 arch/arm/mach-stm32mp/cmd_poweroff.c | 24 ------------------------
 drivers/power/pmic/Kconfig           |  1 +
 drivers/sysreset/Kconfig             | 10 ++++++++++
 drivers/sysreset/sysreset-uclass.c   | 18 ++++++++++++++++++
 6 files changed, 30 insertions(+), 27 deletions(-)  delete mode 100644

arch/arm/mach-stm32mp/cmd_poweroff.c

arch/Kconfig +1 -0
@@ -91,6 +91,7 @@ config SANDBOX
 	select LZO
 	select SPI
 	select SUPPORT_OF_CONTROL
+	select SYSRESET_CMD_POWEROFF if CMD_POWEROFF
 	imply BITREVERSE
 	select BLOBLIST
 	imply CMD_DM
arch/arm/mach-stm32mp/Makefile +0 -0
index 1493914a11..f59ced5ee1 100644
@@ -11,9 +11,6 @@ ifdef CONFIG_SPL_BUILD  obj-y += spl.o  else  obj-y +=

bsec.o -ifndef CONFIG_STM32MP1_TRUSTED -obj-$(CONFIG_SYSRESET) += cmd_poweroff.o -endif endif
obj-$(CONFIG_ARMV7_PSCI) += psci.o obj-$(CONFIG_$(SPL_)DM_REGULATOR) += pwr_regulator.o diff --git
a/arch/arm/mach-stm32mp/cmd_poweroff.c b/arch/arm/mach- stm32mp/cmd_poweroff.c
deleted file mode 100644
index 62347425a0..0000000000

arch/arm/mach-stm32mp/cmd_poweroff.c deleted +0 -23
@@ -1,24 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
-/*
- * Copyright (C) 2019, STMicroelectronics - All Rights Reserved
- */
-
-#include <common.h>
-#include <command.h>
-#include <sysreset.h>
-
-int do_poweroff(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) -{
-	int ret;
-
-	puts("poweroff ...\n");
-	mdelay(100);
-
-	ret = sysreset_walk(SYSRESET_POWER_OFF);
-
-	if (ret == -EINPROGRESS)
-		mdelay(1000);
-
-	/*NOTREACHED when power off*/
-	return CMD_RET_FAILURE;
-}
drivers/power/pmic/Kconfig index renamed from drivers/power/pmic/Kconfig +0 -0

b0cd260354..52edb29b48 100644

drivers/power/pmic/Kconfig +1 -0
@@ -234,6 +234,7 @@ config DM_PMIC_TPS65910  config PMIC_STPMIC1
 	bool "Enable support for STMicroelectronics STPMIC1 PMIC"
 	depends on DM_PMIC && DM_I2C
+	select SYSRESET_CMD_POWEROFF if CMD_POWEROFF &&

!ARM_PSCI_FW

drivers/power/pmic/Kconfig +0 -0
 	---help---
 	The STPMIC1 PMIC provides 4 BUCKs, 6 LDOs, 1 VREF and 2 power

switches.

drivers/power/pmic/Kconfig +0 -0
 	It is accessed via an I2C interface. The device is used with STM32MP1
drivers/sysreset/Kconfig index renamed from drivers/sysreset/Kconfig +0 -0

30aed2c4c1..4c883923bf 100644

drivers/sysreset/Kconfig +10 -0
@@ -33,6 +33,16 @@ config TPL_SYSRESET
 
 if SYSRESET
 
+if CMD_POWEROFF
+
+config SYSRESET_CMD_POWEROFF
+	bool "sysreset implementation of the poweroff command"
+	help
+	  This should be selected by the appropriate PMIC driver if
+	  the poweroff command is enabled.
+
+endif
+
 config SYSRESET_GPIO
 	bool "Enable support for GPIO reset driver"
 	select DM_GPIO
drivers/sysreset/sysreset- renamed from drivers/sysreset/sysreset-uclass.c +0 -0

uclass.c
index ad831c703a..39202588ae 100644

drivers/sysreset/sysreset-uclass.c +18 -1
@@ -118,6 +118,24 @@ int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char *
 const argv[])
 	return 0;
 }
 
+#if IS_ENABLED(CONFIG_SYSRESET_CMD_POWEROFF)
+int do_poweroff(cmd_tbl_t *cmdtp, int flag, int argc, char * const
+argv[]) {
+	int ret;
+
+	puts("poweroff ...\n");
+	mdelay(100);
+
+	ret = sysreset_walk(SYSRESET_POWER_OFF);
+
+	if (ret == -EINPROGRESS)
+		mdelay(1000);
+
+	/*NOTREACHED when power off*/
+	return CMD_RET_FAILURE;
+}
+#endif
+
 static int sysreset_post_bind(struct udevice *dev)  {  #if
 defined(CONFIG_NEEDS_MANUAL_RELOC)
--
Quoted 1 line

2.21.0

Regards

Patrick Delaunay

#4 lore raw

PATCH v2 3/3 rk8xx: add a sysreset driver for poweroff

In reply to Urja Rannikko

Based on snooping around the linux kernel rk8xx driver. Tested on an ASUS C201.

---
 drivers/power/pmic/Kconfig |  1 +
 drivers/power/pmic/rk8xx.c | 62 +++++++++++++++++++++++++++++++++++---
 include/power/rk8xx_pmic.h |  4 +++
 3 files changed, 63 insertions(+), 4 deletions(-)
drivers/power/pmic/Kconfig +1 -0
index 52edb29b48..3f6e30d503 100644
@@ -124,6 +124,7 @@ config PMIC_PM8916
 config PMIC_RK8XX
 	bool "Enable support for Rockchip PMIC RK8XX"
 	depends on DM_PMIC
+	select SYSRESET_CMD_POWEROFF if CMD_POWEROFF
 	---help---
 	The Rockchip RK808 PMIC provides four buck DC-DC convertors, 8 LDOs,
 	an RTC and two low Rds (resistance (drain to source)) switches. It is
drivers/power/pmic/rk8xx.c +58 -4

93 lines not on this page · raw message

include/power/rk8xx_pmic.h +4 -0
index c06248f751..565b35985e 100644
@@ -177,6 +177,10 @@ enum {
 
 #define RK8XX_ID_MSK	0xfff0
 
+/* DEVCTRL bits for poweroff */
+#define DEV_OFF_RST	BIT(3)
+#define DEV_OFF		BIT(0)
+
 struct rk8xx_reg_table {
 	char *name;
 	u8 reg_ctl;
Signature · 1 line
2.21.0
#5 lore raw

PATCH v2 3/3 rk8xx: add a sysreset driver for poweroff

Hi Urja, Simon,

This patch is not able to pass the sandbox_spl test, it reports:
[1] 26463 segmentation fault (core dumped) ./u-boot

The driver looks good to me, no idea what cause the issue.

Thanks,
- Kever

Quoted 153 lines · Urja Rannikko <[email protected]> 于2019年5月17日周五 上午5:49写道:

Based on snooping around the linux kernel rk8xx driver. Tested on an ASUS C201.

---
 drivers/power/pmic/Kconfig |  1 +
 drivers/power/pmic/rk8xx.c | 62 +++++++++++++++++++++++++++++++++++---
 include/power/rk8xx_pmic.h |  4 +++
 3 files changed, 63 insertions(+), 4 deletions(-)
drivers/power/pmic/Kconfig +1 -0
index 52edb29b48..3f6e30d503 100644
@@ -124,6 +124,7 @@ config PMIC_PM8916
 config PMIC_RK8XX
        bool "Enable support for Rockchip PMIC RK8XX"
        depends on DM_PMIC
+       select SYSRESET_CMD_POWEROFF if CMD_POWEROFF
        ---help---
        The Rockchip RK808 PMIC provides four buck DC-DC convertors, 8
 LDOs,

an RTC and two low Rds (resistance (drain to source)) switches. It
is

drivers/power/pmic/rk8xx.c +13 -4
index 25c339ab12..52e41051ae 100644
@@ -6,6 +6,9 @@
 
 #include <common.h>
 #include <dm.h>
+#include <sysreset.h>
+#include <dm/device.h>
+#include <dm/lists.h>
 #include <errno.h>
 #include <power/rk8xx_pmic.h>
 #include <power/pmic.h>
@@ -49,9 +52,9 @@ static int rk8xx_read(struct udevice *dev, uint reg,
 uint8_t *buff, int len)
        return 0;
 }
 
-#if CONFIG_IS_ENABLED(PMIC_CHILDREN)
 static int rk8xx_bind(struct udevice *dev)
 {
+#if CONFIG_IS_ENABLED(PMIC_CHILDREN)
        ofnode regulators_node;
        int children;
@@ -68,10 +71,15 @@ static int rk8xx_bind(struct udevice *dev)
        if (!children)
                debug("%s: %s - no child found\n", __func__, dev->name);
 
+#endif
+
+       if (CONFIG_IS_ENABLED(SYSRESET))
+               return device_bind_driver(dev, "rk8xx-sysreset",
+                                         "rk8xx-sysreset", NULL);
+
        /* Always return success for this device */
        return 0;
 }
-#endif
 
 static int rk8xx_probe(struct udevice *dev)
 {
@@ -103,10 +111,56 @@ U_BOOT_DRIVER(pmic_rk8xx) = {
        .name = "rk8xx pmic",
        .id = UCLASS_PMIC,
        .of_match = rk8xx_ids,
-#if CONFIG_IS_ENABLED(PMIC_CHILDREN)
        .bind = rk8xx_bind,
-#endif
        .priv_auto_alloc_size   = sizeof(struct rk8xx_priv),
        .probe = rk8xx_probe,
        .ops = &rk8xx_ops,
 };
+
+#if IS_ENABLED(CONFIG_SYSRESET)
+/* NOTE: Should only enable this function if the

rockchip,system-power-manager
+ * property is in the device tree node, but it is there in every board that has
+ * an rk8xx in u-boot currently, so this is left as an excercise for later.
+ */
+static int rk8xx_sysreset_request(struct udevice *dev, enum sysreset_t type)

drivers/power/pmic/rk8xx.c +41 -0
+{
+       struct udevice *pmic_dev;
+       struct rk8xx_priv *priv;
+       int ret;
+       u8 bits;
+
+       if (type != SYSRESET_POWER_OFF)
+               return -EPROTONOSUPPORT;
+
+       ret = uclass_get_device_by_driver(UCLASS_PMIC,
+                                         DM_GET_DRIVER(pmic_rk8xx),
+                                         &pmic_dev);
+
+       if (ret)
+               return -EOPNOTSUPP;
+
+       priv = dev_get_priv(pmic_dev);
+
+       if (priv->variant == RK818_ID)
+               bits = DEV_OFF;
+       else
+               bits = DEV_OFF_RST;
+
+       ret = pmic_clrsetbits(pmic_dev, REG_DEVCTRL, 0, bits);
+
+       if (ret < 0)
+               return ret;
+
+       return -EINPROGRESS;
+}
+
+static struct sysreset_ops rk8xx_sysreset_ops = {
+       .request = rk8xx_sysreset_request,
+};
+
+U_BOOT_DRIVER(rk8xx_sysreset) = {
+       .name = "rk8xx-sysreset",
+       .id = UCLASS_SYSRESET,
+       .ops = &rk8xx_sysreset_ops,
+};
+#endif
include/power/rk8xx_pmic.h +4 -1
index c06248f751..565b35985e 100644
@@ -177,6 +177,10 @@ enum {
 
 #define RK8XX_ID_MSK   0xfff0
 
+/* DEVCTRL bits for poweroff */
+#define DEV_OFF_RST    BIT(3)
+#define DEV_OFF                BIT(0)
+
 struct rk8xx_reg_table {
        char *name;
        u8 reg_ctl;
--

2.21.0

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

#6 lore raw

PATCH v2 3/3 rk8xx: add a sysreset driver for poweroff

Hi Kever,

Quoted 6 lines · Kever Yang

Hi Urja, Simon,

This patch is not able to pass the sandbox_spl test, it reports:
[1] 26463 segmentation fault (core dumped) ./u-boot

Quoted 17 lines

The driver looks good to me, no idea what cause the issue.

Thanks,
- Kever

Quoted 11 lines · Urja Rannikko <[email protected]> 于2019年5月17日周五 上午5:49写道:

Based on snooping around the linux kernel rk8xx driver. Tested on an ASUS C201.

---
 drivers/power/pmic/Kconfig |  1 +
 drivers/power/pmic/rk8xx.c | 62 +++++++++++++++++++++++++++++++++++---
 include/power/rk8xx_pmic.h |  4 +++
 3 files changed, 63 insertions(+), 4 deletions(-)

This driver is enabled for sandbox, although I doubt it is in the device tree, so I'm not sure why it would be called. But if it is, and it directly accesses memory, then it might be the reason.

You should run the test under gdb to see where it is crashing.

Regards,
Simon

#7 lore raw

PATCH v2 3/3 rk8xx: add a sysreset driver for poweroff【请注意,邮件由[email protected]代发】

Simon, Stephen,

Quoted 24 lines · Simon Glass

Hi Kever,

Quoted 5 lines · Kever Yang

Hi Urja, Simon,

This patch is not able to pass the sandbox_spl test, it reports:
[1] 26463 segmentation fault (core dumped) ./u-boot

Quoted 16 lines

The driver looks good to me, no idea what cause the issue.

Thanks,
- Kever

Quoted 10 lines · Urja Rannikko <[email protected]> 于2019年5月17日周五 上午5:49写道:

Based on snooping around the linux kernel rk8xx driver. Tested on an ASUS C201.

---
  drivers/power/pmic/Kconfig |  1 +
  drivers/power/pmic/rk8xx.c | 62 +++++++++++++++++++++++++++++++++++---
  include/power/rk8xx_pmic.h |  4 +++
  3 files changed, 63 insertions(+), 4 deletions(-)
Quoted 5 lines

This driver is enabled for sandbox, although I doubt it is in the device tree, so I'm not sure why it would be called. But if it is, and it directly accesses memory, then it might be the reason.

You should run the test under gdb to see where it is crashing.

gdb output is:
Program received signal SIGSEGV, Segmentation fault. 0x00005555556182c6 in strcmp (cs=cs at entry=0x55555566023b "root_driver", ct=0x1 <error: Cannot access memory@address 0x1>)
    at lib/string.c:190
190            if ((__res = *cs - *ct++) != 0 || !*cs++)

This does not help much for crashing reason, and I have narrow down the cause, I believe the
crash related to "DM_GET_DRIVER(pmic_rk8xx)",
- if I replace the 'pmic_rk8xx' in DM_GET_DRIVER() to any of other available driver, u-boot does not crash;
- if I move the new 'rk8xx_sysreset' driver to other files, eg. pmic/sandbox.c, u-boot does not crash;
Any more suggestion, or could you help to cherry pick this patch, and you should reproduce
this issue:
    make sandbox_spl_defconfig all
    ./u-boot

Thanks,
- Kever

Quoted 4 lines

Regards,
Simon

#8 lore raw

PATCH v2 1/3 sysreset: switch to using SYSRESET_POWER_OFF for poweroff

In reply to Urja Rannikko
Quoted 4 lines · Urja Rannikko

It seems that SYSRESET_POWER_OFF was added recently, and all previous code used SYSRESET_POWER for poweroff. SYSRESET_POWER is supposed to be a PMIC-level power cycle, not a poweroff.

SYSRESET_POWER means to do a power reset (removing and reinstating all power) SYSRESET_POWER_OFF means to turn the device off and leave it off

Quoted 75 lines

---
v2: Do not change STPMIC1 driver (thats actually SYSRESET_POWER)

Note: I didnt touch the test/dm/sysreset.c code yet, mostly because I wanted to get feedback on this first and that i'd need to understand the tests properly to do that (and i havent used them before at all).

---
 arch/arm/mach-stm32mp/cmd_poweroff.c | 2 +-
 arch/sandbox/cpu/state.c             | 2 +-
 drivers/sysreset/sysreset_psci.c     | 2 +-
 drivers/sysreset/sysreset_sandbox.c  | 4 ++--
 4 files changed, 5 insertions(+), 5 deletions(-)
arch/arm/mach-stm32mp/cmd_poweroff.c +1 -1
index f54dd1daf2..62347425a0 100644
@@ -14,7 +14,7 @@ int do_poweroff(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
        puts("poweroff ...\n");
        mdelay(100);
 
-       ret = sysreset_walk(SYSRESET_POWER);
+       ret = sysreset_walk(SYSRESET_POWER_OFF);
 
        if (ret == -EINPROGRESS)
                mdelay(1000);
arch/sandbox/cpu/state.c +1 -1
index d3b9c05985..dee5fde4f7 100644
@@ -355,7 +355,7 @@ void state_reset_for_test(struct sandbox_state *state)
 {
        /* No reset yet, so mark it as such. Always allow power reset */
        state->last_sysreset = SYSRESET_COUNT;
-       state->sysreset_allowed[SYSRESET_POWER] = true;
+       state->sysreset_allowed[SYSRESET_POWER_OFF] = true;
 
        memset(&state->wdt, '\0', sizeof(state->wdt));
        memset(state->spi, '\0', sizeof(state->spi));
drivers/sysreset/sysreset_psci.c +1 -1
index de2ec8aeb1..c7907b3226 100644
@@ -18,7 +18,7 @@ static int psci_sysreset_request(struct udevice *dev, enum sysreset_t type)
        case SYSRESET_COLD:
                function_id = PSCI_0_2_FN_SYSTEM_RESET;
                break;
-       case SYSRESET_POWER:
+       case SYSRESET_POWER_OFF:
                function_id = PSCI_0_2_FN_SYSTEM_OFF;
                break;
        default:
drivers/sysreset/sysreset_sandbox.c +2 -3
index 38e2a7e241..8bc9f4b4cc 100644
@@ -57,13 +57,13 @@ static int sandbox_sysreset_request(struct udevice *dev, enum sysreset_t type)
        case SYSRESET_COLD:
                state->last_sysreset = type;
                break;
-       case SYSRESET_POWER:
+       case SYSRESET_POWER_OFF:
                state->last_sysreset = type;
                if (!state->sysreset_allowed[type])
                        return -EACCES;
                sandbox_exit();
                break;
-       case SYSRESET_POWER_OFF:
+       case SYSRESET_POWER:
                if (!state->sysreset_allowed[type])
                        return -EACCES;
        default:
--
Quoted 2 lines

2.21.0

I actually sent a patch to the sandbox driver...er no I didn't, oops. I'll dig up the series and send it.

Regards,
Simopn

#9 lore raw

PATCH v2 1/3 sysreset: switch to using SYSRESET_POWER_OFF for poweroff

In reply to Urja Rannikko

Hi Urja,

Quoted 6 lines

It seems that SYSRESET_POWER_OFF was added recently, and all previous code used SYSRESET_POWER for poweroff. SYSRESET_POWER is supposed to be a PMIC-level power cycle, not a poweroff.

For information: complete support of booth POWER sysreset case for stmpic1 is added by

                          http://patchwork.ozlabs.org/project/uboot/list/?series=108685
Quoted 75 lines

---
v2: Do not change STPMIC1 driver (thats actually SYSRESET_POWER)

Note: I didnt touch the test/dm/sysreset.c code yet, mostly because I wanted to get feedback on this first and that i'd need to understand the tests properly to do that (and i havent used them before at all).

---
 arch/arm/mach-stm32mp/cmd_poweroff.c | 2 +-
 arch/sandbox/cpu/state.c             | 2 +-
 drivers/sysreset/sysreset_psci.c     | 2 +-
 drivers/sysreset/sysreset_sandbox.c  | 4 ++--
 4 files changed, 5 insertions(+), 5 deletions(-)
arch/arm/mach- renamed from arch/arm/mach-stm32mp/cmd_poweroff.c +0 -0

stm32mp/cmd_poweroff.c
index f54dd1daf2..62347425a0 100644

arch/arm/mach-stm32mp/cmd_poweroff.c +1 -1
@@ -14,7 +14,7 @@ int do_poweroff(cmd_tbl_t *cmdtp, int flag, int argc, char *
 const argv[])
 	puts("poweroff ...\n");
 	mdelay(100);
 
-	ret = sysreset_walk(SYSRESET_POWER);
+	ret = sysreset_walk(SYSRESET_POWER_OFF);
 
 	if (ret == -EINPROGRESS)
arch/arm/mach-stm32mp/cmd_poweroff.c +0 -0
 		mdelay(1000);
arch/sandbox/cpu/state.c index renamed from arch/sandbox/cpu/state.c +0 -0

d3b9c05985..dee5fde4f7 100644

arch/sandbox/cpu/state.c +1 -1
@@ -355,7 +355,7 @@ void state_reset_for_test(struct sandbox_state *state)  {
 	/* No reset yet, so mark it as such. Always allow power reset */
 	state->last_sysreset = SYSRESET_COUNT;
-	state->sysreset_allowed[SYSRESET_POWER] = true;
+	state->sysreset_allowed[SYSRESET_POWER_OFF] = true;
 
 	memset(&state->wdt, '\0', sizeof(state->wdt));
 	memset(state->spi, '\0', sizeof(state->spi)); diff --git

a/drivers/sysreset/sysreset_psci.c b/drivers/sysreset/sysreset_psci.c index de2ec8aeb1..c7907b3226 100644

drivers/sysreset/sysreset_psci.c +1 -1
@@ -18,7 +18,7 @@ static int psci_sysreset_request(struct udevice *dev, enum
 sysreset_t type)
 	case SYSRESET_COLD:
 		function_id = PSCI_0_2_FN_SYSTEM_RESET;
 		break;
-	case SYSRESET_POWER:
+	case SYSRESET_POWER_OFF:
 		function_id = PSCI_0_2_FN_SYSTEM_OFF;
 		break;
drivers/sysreset/sysreset_psci.c +0 -0
 	default:
drivers/sysreset/sysreset_sandbox.c +2 -2
index 38e2a7e241..8bc9f4b4cc 100644
@@ -57,13 +57,13 @@ static int sandbox_sysreset_request(struct udevice *dev,
 enum sysreset_t type)
 	case SYSRESET_COLD:
 		state->last_sysreset = type;
 		break;
-	case SYSRESET_POWER:
+	case SYSRESET_POWER_OFF:
 		state->last_sysreset = type;
 		if (!state->sysreset_allowed[type])
 			return -EACCES;
 		sandbox_exit();
 		break;
-	case SYSRESET_POWER_OFF:
+	case SYSRESET_POWER:
 		if (!state->sysreset_allowed[type])
 			return -EACCES;
Quoted 3 lines

default:
--
2.21.0

Regards

Patrick