Skip to contentSkip to conversation

imx: mx6sabresd: fix boot hang with video

PATCH New Peng Fan 2 participants 3 messages Apr 25, 2019 – May 20, 2019

Subsystems (2)
lore
Share & tools
lore

Peng Fan

author
#0 lore raw

PATCH 1/1 imx: mx6sabresd: fix boot hang with video

Meet the following boot hang.
"
U-Boot SPL 2019.04-00661-gdc80a012e4 (Apr 25 2019 - 10:31:57 +0800) Trying to boot from MMC1

U-Boot 2019.04-00661-gdc80a012e4 (Apr 25 2019 - 10:31:57 +0800)

CPU:   Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU:   Automotive temperature grade (-40C to 125C)Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Smart Device Board
Board: MX6-SabreSD
I2C:   ready
DRAM:  1 GiB

Video device 'ipu at 2400000' cannot allocate frame buffer memory -ensure the device is set up before relocation Error binding driver 'ipuv3_video': -28
Video device 'ipu at 2800000' cannot allocate frame buffer memory -ensure the device is set up before relocation Error binding driver 'ipuv3_video': -28
Some drivers failed to bind
Error binding driver 'generic_simple_bus': -28
Some drivers failed to bind
initcall sequence 4ffe4500 failed at call 1780dfb7 (err=-28)
"

1. fdtdec_get_alias_seq will use "video" as base, however in alias node, we use ipux, so add new alias for U-Boot dts.
2. DM_VIDEO is enabled, however reserve_video is called before relocation, so to make DM_VIDEO work before relocation, need to set SYS_MALLOC_F_LEN
3. defconfig is updated with savedefconfig

Note: I do not have a video panel to test, but with this patch, U-Boot
boots up again, below log.

"
U-Boot SPL 2019.04-00662-g0b62453bff (Apr 25 2019 - 10:36:31 +0800) Trying to boot from MMC1

U-Boot 2019.04-00662-g0b62453bff (Apr 25 2019 - 10:36:31 +0800)

CPU:   Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU:   Automotive temperature grade (-40C to 125C) at 34C
Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Smart Device Board
Board: MX6-SabreSD
I2C:   ready
DRAM:  1 GiB
PMIC:  PFUZE100 ID=0x10
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 3

Loading Environment from MMC... *** Warning - bad CRC, using default environment

PCI:   pcie phy link never came up
In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0

"

---
 arch/arm/dts/imx6q.dtsi      | 1 +
 arch/arm/dts/imx6qdl.dtsi    | 1 +
 configs/mx6sabresd_defconfig | 6 +++---
 3 files changed, 5 insertions(+), 3 deletions(-)
arch/arm/dts/imx6q.dtsi +1 -0
index ab1716b6b0..bc104f7bbb 100644
@@ -9,6 +9,7 @@
 / {
 	aliases {
 		ipu1 = &ipu2;
+		video1 = &ipu2;
 		spi4 = &ecspi5;
 	};
 
arch/arm/dts/imx6qdl.dtsi +1 -0
index c0a9478008..83eeb5cc59 100644
@@ -33,6 +33,7 @@
 		i2c1 = &i2c2;
 		i2c2 = &i2c3;
 		ipu0 = &ipu1;
+		video0 = &ipu1;
 		mmc0 = &usdhc1;
 		mmc1 = &usdhc2;
 		mmc2 = &usdhc3;
configs/mx6sabresd_defconfig +3 -3
index eaf0f01004..5b527cbd5b 100644
@@ -4,13 +4,13 @@ CONFIG_SYS_TEXT_BASE=0x17800000
 CONFIG_SPL_GPIO_SUPPORT=y
 CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x4000
 CONFIG_TARGET_MX6SABRESD=y
 CONFIG_SPL_MMC_SUPPORT=y
 CONFIG_SPL_SERIAL_SUPPORT=y
 CONFIG_SPL=y
-CONFIG_SPL_LIBDISK_SUPPORT=y
 CONFIG_NR_DRAM_BANKS=1
-# CONFIG_SYS_MALLOC_F is not set
+CONFIG_SPL_LIBDISK_SUPPORT=y
 CONFIG_FIT=y
 CONFIG_SPL_FIT_PRINT=y
 CONFIG_SPL_LOAD_FIT=y
@@ -62,6 +62,7 @@ CONFIG_OF_LIST="imx6q-sabresd imx6qp-sabresd imx6dl-sabresd"
 CONFIG_MULTI_DTB_FIT=y
 CONFIG_SPL_MULTI_DTB_FIT=y
 CONFIG_SPL_OF_LIST="imx6dl-sabresd imx6q-sabresd imx6qp-sabresd"
+CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
 CONFIG_SPL_DM=y
@@ -97,4 +98,3 @@ CONFIG_USB_HOST_ETHER=y
 CONFIG_USB_ETHER_ASIX=y
 CONFIG_DM_VIDEO=y
 CONFIG_VIDEO_IPUV3=y
-# CONFIG_VIDEO_SW_CURSOR is not set
Signature · 1 line
2.16.4
#2 lore raw

PATCH 1/1 imx: mx6sabresd: fix boot hang with video

In reply to Peng Fan

On Thu, 25 Apr 2019 02:36:22 +0000
Peng Fan peng.fan at nxp.com wrote:
...

Quoted 6 lines
---
 arch/arm/dts/imx6q.dtsi      | 1 +
 arch/arm/dts/imx6qdl.dtsi    | 1 +
 configs/mx6sabresd_defconfig | 6 +++---
 3 files changed, 5 insertions(+), 3 deletions(-)

Applied to u-boot-video/master after rebasing defconfig changes. Thanks!

--
Anatolij