Skip to contentSkip to conversation

Allow VINDPM to be set in the device tree

PATCH In review Angus Ainslie (Purism) 3 participants 5 messages May 20, 2019 – Jun 25, 2019

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

cover Allow VINDPM to be set in the device tree

The BQ25890 can control the input voltage limit so allow it to be set.

Angus Ainslie (Purism) (1):
dt-bindings: power: supply: Add documentation for the VINDPM
properties

Eric Kuzmenko (1):
power: supply: bq25890: Add support for setting bq25890 and bq25896's
VINDPM

 .../devicetree/bindings/power/supply/bq25890.txt    |  8 ++++++++
 drivers/power/supply/bq25890_charger.c              | 13 ++++++++++++-
 2 files changed, 20 insertions(+), 1 deletion(-)
Signature · 1 line
2.17.1
#1 lore raw

PATCH 1/2 power: supply: bq25890: Add support for setting bq25890 and bq25896's VINDPM

From: Eric Kuzmenko <[email protected]>

The bq25890 has low voltage protection on VIN. Allow the register to be set from the device tree.

---
 drivers/power/supply/bq25890_charger.c | 13 ++++++++++++-
 1 file changed, 12 insertions(+), 1 deletion(-)
drivers/power/supply/bq25890_charger.c +12 -1
index 66991e6f75d9..34fc89776994 100644
@@ -75,6 +75,8 @@ struct bq25890_init_data {
 	u8 boosti;	/* boost current limit		*/
 	u8 boostf;	/* boost frequency		*/
 	u8 ilim_en;	/* enable ILIM pin		*/
+	u8 force_vindpm;/* force vinmin threshold	*/
+	u8 vindpm;	/* vinmin threshold		*/
 	u8 treg;	/* thermal regulation threshold */
 };
 
@@ -250,6 +252,7 @@ enum bq25890_table_ids {
 	TBL_VREG,
 	TBL_BOOSTV,
 	TBL_SYSVMIN,
+	TBL_VINDPM,
 
 	/* lookup tables */
 	TBL_TREG,
@@ -289,6 +292,7 @@ static const union {
 	[TBL_VREG] =	{ .rt = {3840000, 4608000, 16000} },	 /* uV */
 	[TBL_BOOSTV] =	{ .rt = {4550000, 5510000, 64000} },	 /* uV */
 	[TBL_SYSVMIN] = { .rt = {3000000, 3700000, 100000} },	 /* uV */
+	[TBL_VINDPM] =	{ .rt = {2600000, 15300000, 100000} },	 /* uV */
 
 	/* lookup tables */
 	[TBL_TREG] =	{ .lt = {bq25890_treg_tbl, BQ25890_TREG_TBL_SIZE} },
@@ -621,6 +625,8 @@ static int bq25890_hw_init(struct bq25890_device *bq)
 		{F_BOOSTI,	 bq->init_data.boosti},
 		{F_BOOSTF,	 bq->init_data.boostf},
 		{F_EN_ILIM,	 bq->init_data.ilim_en},
+		{F_FORCE_VINDPM, bq->init_data.force_vindpm},
+		{F_VINDPM,	 bq->init_data.vindpm},
 		{F_TREG,	 bq->init_data.treg}
 	};
 
@@ -783,11 +789,14 @@ static int bq25890_fw_read_u32_props(struct bq25890_device *bq)
 		{"ti,boost-max-current", false, TBL_BOOSTI, &init->boosti},
 
 		/* optional properties */
-		{"ti,thermal-regulation-threshold", true, TBL_TREG, &init->treg}
+		{"ti,thermal-regulation-threshold",
+			true, TBL_TREG, &init->treg},
+		{"ti,vinmin-threshold", true, TBL_VINDPM, &init->vindpm}
 	};
 
 	/* initialize data for optional properties */
 	init->treg = 3; /* 120 degrees Celsius */
+	init->vindpm = 0x12; /* 4.4V */
 
 	for (i = 0; i < ARRAY_SIZE(props); i++) {
 		ret = device_property_read_u32(bq->dev, props[i].name,
@@ -820,6 +829,8 @@ static int bq25890_fw_probe(struct bq25890_device *bq)
 
 	init->ilim_en = device_property_read_bool(bq->dev, "ti,use-ilim-pin");
 	init->boostf = device_property_read_bool(bq->dev, "ti,boost-low-freq");
+	init->force_vindpm =
+		device_property_read_bool(bq->dev, "ti,use-vinmin-threshold");
 
 	return 0;
 }
Signature · 1 line
2.17.1
#2 lore raw

PATCH 2/2 dt-bindings: power: supply: Add documentation for the VINDPM properties

In reply to Angus Ainslie (Purism)

Add documentation on how to control VINDPM from the devicetree.

---
 .../devicetree/bindings/power/supply/bq25890.txt          | 8 ++++++++
 1 file changed, 8 insertions(+)
Documentation/devicetree/bindings/power/supply/bq25890.txt +8 -0
index dc0568933359..fe8b709dd666 100644
@@ -26,9 +26,15 @@ Optional properties:
 - ti,use-ilim-pin: boolean, if present the ILIM resistor will be used and the
     input current will be the lower between the resistor setting and the IINLIM
     register setting;
+- ti,use-vinmin-threshold: boolean, if present the FORCE_VINDPM bit will be set
+    and the input voltage limit will be configured based on "ti,vinmin-threshold"
 - ti,thermal-regulation-threshold: integer, temperature above which the charge
     current is lowered, to avoid overheating (in degrees Celsius). If omitted,
     the default setting will be used (120 degrees);
+- ti,vinmin-threshold: integer, lower absolute threshold for VINDPM. If the
+    voltage falls below this threshold the charge current is reduced until the
+    input voltage rises above the input voltage limit. If omitted, the default
+    setting will be used (4.4V);
 
 Example:
 
@@ -46,4 +52,6 @@ bq25890 {
 
         ti,use-ilim-pin;
         ti,thermal-regulation-threshold = <120>;
+        ti,use-vinmin-threshold;
+        ti,vinmin-threshold = <3900000>;
 };
Signature · 1 line
2.17.1
maintainer
#3 lore raw

Re: [PATCH 2/2] dt-bindings: power: supply: Add documentation for the VINDPM properties

Quoted 12 lines · Angus Ainslie (Purism)

Add documentation on how to control VINDPM from the devicetree.

---
 .../devicetree/bindings/power/supply/bq25890.txt          | 8 ++++++++
 1 file changed, 8 insertions(+)
Documentation/devicetree/bindings/power/supply/bq25890.txt +0 -0
index dc0568933359..fe8b709dd666 100644

Documentation/devicetree/bindings/power/supply/bq25890.txt Optional properties: · line 30

Quoted 5 lines
Documentation/devicetree/bindings/power/supply/bq25890.txt +2 -0
@@ -26,9 +26,15 @@ Optional properties:
 - ti,use-ilim-pin: boolean, if present the ILIM resistor will be used and the
     input current will be the lower between the resistor setting and the IINLIM
     register setting;
+- ti,use-vinmin-threshold: boolean, if present the FORCE_VINDPM bit will be set
+    and the input voltage limit will be configured based on "ti,vinmin-threshold"

Isn't presence of ti,vinmin-threshold enough to determine whether to set FORCE_VINDPM or not? Just get rid of the default being 4.4V.

Quoted 20 lines
Documentation/devicetree/bindings/power/supply/bq25890.txt +6 -0
 - ti,thermal-regulation-threshold: integer, temperature above which the charge
     current is lowered, to avoid overheating (in degrees Celsius). If omitted,
     the default setting will be used (120 degrees);
+- ti,vinmin-threshold: integer, lower absolute threshold for VINDPM. If the
+    voltage falls below this threshold the charge current is reduced until the
+    input voltage rises above the input voltage limit. If omitted, the default
+    setting will be used (4.4V);
 
 Example:
 
@@ -46,4 +52,6 @@ bq25890 {
 
         ti,use-ilim-pin;
         ti,thermal-regulation-threshold = <120>;
+        ti,use-vinmin-threshold;
+        ti,vinmin-threshold = <3900000>;
 };
Signature · 1 line
2.17.1
#4 lore raw

Re: [PATCH 2/2] dt-bindings: power: supply: Add documentation for the VINDPM properties

Hi,

Quoted 8 lines · Rob Herring
Quoted 7 lines · Angus Ainslie (Purism)

Add documentation on how to control VINDPM from the devicetree.

---
 .../devicetree/bindings/power/supply/bq25890.txt          | 8 ++++++++
 1 file changed, 8 insertions(+)
Quoted 21 lines

Documentation/devicetree/bindings/power/supply/bq25890.txt Optional properties: · line 30

Quoted 10 lines
Documentation/devicetree/bindings/power/supply/bq25890.txt +2 -0
index dc0568933359..fe8b709dd666 100644
@@ -26,9 +26,15 @@ Optional properties:
 - ti,use-ilim-pin: boolean, if present the ILIM resistor will be used and the
     input current will be the lower between the resistor setting and the IINLIM
     register setting;
+- ti,use-vinmin-threshold: boolean, if present the FORCE_VINDPM bit will be set
+    and the input voltage limit will be configured based on "ti,vinmin-threshold"

Isn't presence of ti,vinmin-threshold enough to determine whether to set FORCE_VINDPM or not? Just get rid of the default being 4.4V.

Quoted 7 lines
Documentation/devicetree/bindings/power/supply/bq25890.txt +4 -0
 - ti,thermal-regulation-threshold: integer, temperature above which the charge
     current is lowered, to avoid overheating (in degrees Celsius). If omitted,
     the default setting will be used (120 degrees);
+- ti,vinmin-threshold: integer, lower absolute threshold for VINDPM. If the
+    voltage falls below this threshold the charge current is reduced until the
+    input voltage rises above the input voltage limit. If omitted, the default
+    setting will be used (4.4V);

We already have a "input-voltage-min-microvolt" property used by Maxim chargers, please resuse that for the bq25890 instead of creating a new property name.

-- Sebastian

Quoted 13 lines
Quoted 13 lines
Documentation/devicetree/bindings/power/supply/bq25890.txt +2 -0
 Example:
 
@@ -46,4 +52,6 @@ bq25890 {
 
         ti,use-ilim-pin;
         ti,thermal-regulation-threshold = <120>;
+        ti,use-vinmin-threshold;
+        ti,vinmin-threshold = <3900000>;
 };
Signature · 1 line
2.17.1