Skip to contentSkip to conversation

ixgbe: Check DDM existence in transceiver before access

PATCH New Mauro S. M. Rodrigues 3 participants 3 messages May 23, 2019 – Jun 13, 2019

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ixgbe: Check DDM existence in transceiver before access

Some transceivers may comply with SFF-8472 but not implement the Digital Diagnostic Monitoring (DDM) interface described in it. The existence of such area is specified by bit 6 of byte 92, set to 1 if implemented.

Currently, due to not checking this bit ixgbe fails trying to read sfp module's eeprom with the follow message:

ethtool -m enP51p1s0f0
Cannot get Module EEPROM data: Input/output error

Because it fails to read the additional 256 bytes in which it was assumed to exist the DDM data.

This issue was noticed using a Mellanox Passive DAC PN 01FT738. The eeprom data was confirmed by Mellanox as correct and present in other Passive DACs in from other manufacturers.

---
 drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c | 3 ++-
 drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h     | 1 +
 2 files changed, 3 insertions(+), 1 deletion(-)
drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c +2 -1
index acba067cc15a..7c52ae8ac005 100644
@@ -3226,7 +3226,8 @@ static int ixgbe_get_module_info(struct net_device *dev,
 		page_swap = true;
 	}
 
-	if (sff8472_rev == IXGBE_SFF_SFF_8472_UNSUP || page_swap) {
+	if (sff8472_rev == IXGBE_SFF_SFF_8472_UNSUP || page_swap ||
+	    !(addr_mode & IXGBE_SFF_DDM_IMPLEMENTED)) {
 		/* We have a SFP, but it does not support SFF-8472 */
 		modinfo->type = ETH_MODULE_SFF_8079;
 		modinfo->eeprom_len = ETH_MODULE_SFF_8079_LEN;
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h +1 -0
index 214b01085718..693c615017cc 100644
@@ -45,6 +45,7 @@
 #define IXGBE_SFF_SOFT_RS_SELECT_10G		0x8
 #define IXGBE_SFF_SOFT_RS_SELECT_1G		0x0
 #define IXGBE_SFF_ADDRESSING_MODE		0x4
+#define IXGBE_SFF_DDM_IMPLEMENTED              0x40
 #define IXGBE_SFF_QSFP_DA_ACTIVE_CABLE		0x1
 #define IXGBE_SFF_QSFP_DA_PASSIVE_CABLE		0x8
 #define IXGBE_SFF_QSFP_CONNECTOR_NOT_SEPARABLE	0x23
Signature · 1 line
2.21.0
#1 lore raw

PATCH 1/1 ixgbe: Check DDM existence in transceiver before access

Quoted 10 lines · On Thu, 23 May 2019 16:11:12 -0300 Mauro wrote:

Some transceivers may comply with SFF-8472 but not implement the Digital Diagnostic Monitoring (DDM) interface described in it. The existence of such area is specified by bit 6 of byte 92, set to 1 if implemented.

Currently, due to not checking this bit ixgbe fails trying to read sfp module's eeprom with the follow message:

ethtool -m enP51p1s0f0
Cannot get Module EEPROM data: Input/output error

Quoted 8 lines

Because it fails to read the additional 256 bytes in which it was assumed to exist the DDM data.

This issue was noticed using a Mellanox Passive DAC PN 01FT738. The eeprom data was confirmed by Mellanox as correct and present in other Passive DACs in from other manufacturers.

Looks reasonable, thanks for the patch!

#2 lore raw

PATCH 1/1 ixgbe: Check DDM existence in transceiver before access

In reply to Mauro S. M. Rodrigues
Quoted 27 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On Behalf Of Mauro S. M. Rodrigues
Sent: Thursday, May 23, 2019 12:11 PM
To: intel-wired-lan at lists.osuosl.org; Kirsher, Jeffrey T <[email protected]>
Cc: gromero at linux.vnet.ibm.com
Subject: [Intel-wired-lan] [PATCH] ixgbe: Check DDM existence in transceiver before access

Some transceivers may comply with SFF-8472 but not implement the Digital Diagnostic Monitoring (DDM) interface described in it. The existence of such area is specified by bit 6 of byte 92, set to 1 if implemented.

Currently, due to not checking this bit ixgbe fails trying to read sfp module's eeprom with the follow message:

ethtool -m enP51p1s0f0
Cannot get Module EEPROM data: Input/output error

Because it fails to read the additional 256 bytes in which it was assumed to exist the DDM data.

This issue was noticed using a Mellanox Passive DAC PN 01FT738. The eeprom data was confirmed by Mellanox as correct and present in other Passive DACs in from other manufacturers.

Quoted 5 lines
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c | 3 ++-
 drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h     | 1 +
 2 files changed, 3 insertions(+), 1 deletion(-)