ARM: omap3: evm: Enable DM_USB in defconfig
PATCH 2/3 ARM: omap3: evm: Enable DM_USB in defconfig
This addresses the following warning message:
===================== WARNING ====================== This board does not use CONFIG_DM_USB. Please update the board to use CONFIG_DM_USB before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info.
====================================================
As USB support for older OMAP3 SoC's improves, OMAP3 EVM can be readily adapted. There is some additional 'gpio-hog' support needed to fully setup USB in a similar manner to Linux.
--- board/ti/evm/evm.c | 31 ------------------------------- configs/omap3_evm_defconfig | 3 +++ include/configs/omap3_evm.h | 2 -- 3 files changed, 3 insertions(+), 33 deletions(-)
board/ti/evm/evm.c +0 -31
@@ -30,11 +30,6 @@#include <linux/usb/musb.h> #include "evm.h" -#ifdef CONFIG_USB_EHCI_HCD -#include <usb.h> -#include <asm/ehci-omap.h> -#endif -#define OMAP3EVM_GPIO_ETH_RST_GEN1 64#define OMAP3EVM_GPIO_ETH_RST_GEN2 7
@@ -307,32 +302,6 @@ void board_mmc_power_init(void) }#endif /* CONFIG_MMC */ -#if defined(CONFIG_USB_EHCI_HCD ) && !defined(CONFIG_SPL_BUILD ) -/* Call usb_stop() before starting the kernel */ -void show_boot_progress (int val) -{ -if (val ==BOOTSTAGE_ID_RUN_OS ) -usb_stop (); -} - -static struct omap_usbhs_board_data usbhs_bdata = { - .port_mode[0 ] =OMAP_USBHS_PORT_MODE_UNUSED , - .port_mode[1 ] =OMAP_EHCI_PORT_MODE_PHY , - .port_mode[2 ] =OMAP_USBHS_PORT_MODE_UNUSED -}; - -int ehci_hcd_init (int index,enum usb_init_type init, -struct ehci_hccr **hccr,struct ehci_hcor **hcor) -{ -return omap_ehci_hcd_init (index, &usbhs_bdata, hccr, hcor); -} - -int ehci_hcd_stop (int index) -{ -return omap_ehci_hcd_stop (); -} -#endif /* CONFIG_USB_EHCI_HCD */ -#if defined(CONFIG_USB_ETHER ) && defined(CONFIG_USB_MUSB_GADGET ) && !defined(CONFIG_CMD_NET )int board_eth_init (bd_t *bis) {
configs/omap3_evm_defconfig +3 -0
@@ -66,7 +66,10 @@ CONFIG_SPI=y CONFIG_DM_SPI=y CONFIG_OMAP3_SPI=y CONFIG_USB=y +CONFIG_DM_USB=y +# CONFIG_SPL_DM_USB is not set CONFIG_USB_EHCI_HCD=y +CONFIG_USB_OMAP3=y CONFIG_USB_MUSB_GADGET=y CONFIG_USB_MUSB_OMAP2PLUS=y CONFIG_USB_GADGET=y
include/configs/omap3_evm.h +0 -2
@@ -56,8 +56,6 @@/* Environment */ #define CONFIG_ENV_SIZE SZ_128K -#define CONFIG_PREBOOT "usb start" -#define MEM_LAYOUT_ENV_SETTINGS \ DEFAULT_LINUX_BOOT_ENV
Signature · 1 line
2.21.0
PATCH 2/3 ARM: omap3: evm: Enable DM_USB in defconfig
Quoted 9 lines · Derald D. Woods
This addresses the following warning message:
===================== WARNING ====================== This board does not use
CONFIG_DM_USB. Please update the board to useCONFIG_DM_USBbefore the v2019.07 release. Failure to update by the deadline may result in board removal. Seedoc/driver-model/MIGRATION.txtfor more info.
====================================================
Quoted 5 lines
As USB support for older OMAP3 SoC's improves, OMAP3 EVM can be readily adapted. There is some additional 'gpio-hog' support needed to fully setup USB in a similar manner to Linux.
Signed-off-by Derald D. Woods <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190714/27781ade/attachment.sig>