Skip to contentSkip to conversation

clk: meson: add support for Amlogic G12B

PATCH Applied Neil Armstrong 3 participants 7 messages May 28, 2019 – Jun 11, 2019

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

v2 cover clk: meson: add support for Amlogic G12B

The Amlogic G12B SoC is very similar with the G12A SoC, sharing most of the features and architecture.
G12B clock tree is very close, the main differences are :
- SYS_PLL is used for the second cluster (otherwise used fir the first on G12a)
- SYS_PLL1 is used for the first cluster (instead of SYS_PLL on G12a)
- A duplicate CPU tree is added for the second cluster
- G12B has additional clocks like for CSI an other components, not handled yet

Dependencies :
- Patch 1, 3 : None
- Patch 2 : Depends on Guillaume's Temperature sensor Clock patches at [1]

This patchset is a spinoff of the v2 Odroid-N2 megapatchset at [2]

Changes since v1 at [3]:
- Added the cpub_clk div2..8 and replaces the ahb/atb/axi/trace divs by muxes
- Added the CLK_GATE_SET_TO_DISABLE flag to ahb/atb/axi/trace gates
- Fixed all the G12A typos
- Added martin's reviewed by on patch 1

Changes since original patchset :
- Added missing sys1_pll div16, cpub div16 and cpub atb/axi/ahb/trace clocks
- Rewrote "This patch .." in commit messages

[1] https://lkml.kernel.org/r/[email protected]
[2] https://lkml.kernel.org/r/[email protected]
[3] https://lkml.kernel.org/r/[email protected]

Neil Armstrong (3):
dt-bindings: clk: meson: add g12b periph clock controller bindings
clk: meson: g12a: Add support for G12B CPUB clocks
clk: meson: g12a: mark fclk_div3 as critical

 .../bindings/clock/amlogic,gxbb-clkc.txt      |   1 +
 drivers/clk/meson/g12a.c                      | 772 ++++++++++++++++++
 drivers/clk/meson/g12a.h                      |  40 +-
 3 files changed, 812 insertions(+), 1 deletion(-)
Signature · 1 line
2.21.0
#1 lore raw

PATCH v2 1/3 dt-bindings: clk: meson: add g12b periph clock controller bindings

Update the documentation to support clock driver for the Amlogic G12B SoC.

G12B clock driver is very close, the main differences are :
- the clock tree is duplicated for the both clusters, and the SYS_PLL are swapped between the clusters
- G12B has additional clocks like for CSI an other components

---
 Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt +1 -0
index 5c8b105be4d6..6eaa52092313 100644
@@ -10,6 +10,7 @@ Required Properties:
 		"amlogic,gxl-clkc" for GXL and GXM SoC,
 		"amlogic,axg-clkc" for AXG SoC.
 		"amlogic,g12a-clkc" for G12A SoC.
+		"amlogic,g12b-clkc" for G12B SoC.
 - clocks : list of clock phandle, one for each entry clock-names.
 - clock-names : should contain the following:
   * "xtal": the platform xtal
Signature · 1 line
2.21.0
#2 lore raw

PATCH v2 2/3 clk: meson: g12a: Add support for G12B CPUB clocks

In reply to Neil Armstrong

Update the Meson G12A Clock driver to support the Amlogic G12B SoC.

G12B clock driver is very close, the main differences are :
- the clock tree is duplicated for the both clusters, and the SYS_PLL are swapped between the clusters
- G12B has additional clocks like for CSI an other components

Here only the cpu clock tree is handled.

---
 drivers/clk/meson/g12a.c | 762 +++++++++++++++++++++++++++++++++++++++
 drivers/clk/meson/g12a.h |  40 +-
 2 files changed, 801 insertions(+), 1 deletion(-)
drivers/clk/meson/g12a.c +762 -0
index a7b621bebb7e..1abe46a95dc1 100644
@@ -150,6 +150,57 @@ static struct clk_regmap g12a_sys_pll = {
 	},
 };
 
+static struct clk_regmap g12b_sys1_pll_dco = {
+	.data = &(struct meson_clk_pll_data){
+		.en = {
+			.reg_off = HHI_SYS1_PLL_CNTL0,
+			.shift   = 28,
+			.width   = 1,
+		},
+		.m = {
+			.reg_off = HHI_SYS1_PLL_CNTL0,
+			.shift   = 0,
+			.width   = 8,
+		},
+		.n = {
+			.reg_off = HHI_SYS1_PLL_CNTL0,
+			.shift   = 10,
+			.width   = 5,
+		},
+		.l = {
+			.reg_off = HHI_SYS1_PLL_CNTL0,
+			.shift   = 31,
+			.width   = 1,
+		},
+		.rst = {
+			.reg_off = HHI_SYS1_PLL_CNTL0,
+			.shift   = 29,
+			.width   = 1,
+		},
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "sys1_pll_dco",
+		.ops = &meson_clk_pll_ro_ops,
+		.parent_names = (const char *[]){ IN_PREFIX "xtal" },
+		.num_parents = 1,
+	},
+};
+
+static struct clk_regmap g12b_sys1_pll = {
+	.data = &(struct clk_regmap_div_data){
+		.offset = HHI_SYS1_PLL_CNTL0,
+		.shift = 16,
+		.width = 3,
+		.flags = CLK_DIVIDER_POWER_OF_TWO,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "sys1_pll",
+		.ops = &clk_regmap_divider_ro_ops,
+		.parent_names = (const char *[]){ "sys1_pll_dco" },
+		.num_parents = 1,
+	},
+};
+
 static struct clk_regmap g12a_sys_pll_div16_en = {
 	.data = &(struct clk_regmap_gate_data){
 		.offset = HHI_SYS_CPU_CLK_CNTL1,
@@ -167,6 +218,23 @@ static struct clk_regmap g12a_sys_pll_div16_en = {
 	},
 };
 
+static struct clk_regmap g12b_sys1_pll_div16_en = {
+	.data = &(struct clk_regmap_gate_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL1,
+		.bit_idx = 24,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "sys1_pll_div16_en",
+		.ops = &clk_regmap_gate_ro_ops,
+		.parent_names = (const char *[]){ "sys1_pll" },
+		.num_parents = 1,
+		/*
+		 * This clock is used to debug the sys_pll range
+		 * Linux should not change it at runtime
+		 */
+	},
+};
+
 static struct clk_fixed_factor g12a_sys_pll_div16 = {
 	.mult = 1,
 	.div = 16,
@@ -178,6 +246,17 @@ static struct clk_fixed_factor g12a_sys_pll_div16 = {
 	},
 };
 
+static struct clk_fixed_factor g12b_sys1_pll_div16 = {
+	.mult = 1,
+	.div = 16,
+	.hw.init = &(struct clk_init_data){
+		.name = "sys1_pll_div16",
+		.ops = &clk_fixed_factor_ops,
+		.parent_names = (const char *[]){ "sys1_pll_div16_en" },
+		.num_parents = 1,
+	},
+};
+
 /* Datasheet names this field as "premux0" */
 static struct clk_regmap g12a_cpu_clk_premux0 = {
 	.data = &(struct clk_regmap_mux_data){
@@ -306,6 +385,150 @@ static struct clk_regmap g12a_cpu_clk = {
 	},
 };
 
+/* Datasheet names this field as "Final_mux_sel" */
+static struct clk_regmap g12b_cpu_clk = {
+	.data = &(struct clk_regmap_mux_data){
+		.offset = HHI_SYS_CPU_CLK_CNTL0,
+		.mask = 0x1,
+		.shift = 11,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "cpu_clk",
+		.ops = &clk_regmap_mux_ro_ops,
+		.parent_names = (const char *[]){ "cpu_clk_dyn",
+						  "sys1_pll" },
+		.num_parents = 2,
+	},
+};
+
+/* Datasheet names this field as "premux0" */
+static struct clk_regmap g12b_cpub_clk_premux0 = {
+	.data = &(struct clk_regmap_mux_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL,
+		.mask = 0x3,
+		.shift = 0,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_dyn0_sel",
+		.ops = &clk_regmap_mux_ro_ops,
+		.parent_names = (const char *[]){ IN_PREFIX "xtal",
+						  "fclk_div2",
+						  "fclk_div3" },
+		.num_parents = 3,
+	},
+};
+
+/* Datasheet names this field as "mux0_divn_tcnt" */
+static struct clk_regmap g12b_cpub_clk_mux0_div = {
+	.data = &(struct clk_regmap_div_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL,
+		.shift = 4,
+		.width = 6,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_dyn0_div",
+		.ops = &clk_regmap_divider_ro_ops,
+		.parent_names = (const char *[]){ "cpub_clk_dyn0_sel" },
+		.num_parents = 1,
+	},
+};
+
+/* Datasheet names this field as "postmux0" */
+static struct clk_regmap g12b_cpub_clk_postmux0 = {
+	.data = &(struct clk_regmap_mux_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL,
+		.mask = 0x1,
+		.shift = 2,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_dyn0",
+		.ops = &clk_regmap_mux_ro_ops,
+		.parent_names = (const char *[]){ "cpub_clk_dyn0_sel",
+						  "cpub_clk_dyn0_div" },
+		.num_parents = 2,
+	},
+};
+
+/* Datasheet names this field as "premux1" */
+static struct clk_regmap g12b_cpub_clk_premux1 = {
+	.data = &(struct clk_regmap_mux_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL,
+		.mask = 0x3,
+		.shift = 16,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_dyn1_sel",
+		.ops = &clk_regmap_mux_ro_ops,
+		.parent_names = (const char *[]){ IN_PREFIX "xtal",
+						  "fclk_div2",
+						  "fclk_div3" },
+		.num_parents = 3,
+	},
+};
+
+/* Datasheet names this field as "Mux1_divn_tcnt" */
+static struct clk_regmap g12b_cpub_clk_mux1_div = {
+	.data = &(struct clk_regmap_div_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL,
+		.shift = 20,
+		.width = 6,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_dyn1_div",
+		.ops = &clk_regmap_divider_ro_ops,
+		.parent_names = (const char *[]){ "cpub_clk_dyn1_sel" },
+		.num_parents = 1,
+	},
+};
+
+/* Datasheet names this field as "postmux1" */
+static struct clk_regmap g12b_cpub_clk_postmux1 = {
+	.data = &(struct clk_regmap_mux_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL,
+		.mask = 0x1,
+		.shift = 18,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_dyn1",
+		.ops = &clk_regmap_mux_ro_ops,
+		.parent_names = (const char *[]){ "cpub_clk_dyn1_sel",
+						  "cpub_clk_dyn1_div" },
+		.num_parents = 2,
+	},
+};
+
+/* Datasheet names this field as "Final_dyn_mux_sel" */
+static struct clk_regmap g12b_cpub_clk_dyn = {
+	.data = &(struct clk_regmap_mux_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL,
+		.mask = 0x1,
+		.shift = 10,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_dyn",
+		.ops = &clk_regmap_mux_ro_ops,
+		.parent_names = (const char *[]){ "cpub_clk_dyn0",
+						  "cpub_clk_dyn1" },
+		.num_parents = 2,
+	},
+};
+
+/* Datasheet names this field as "Final_mux_sel" */
+static struct clk_regmap g12b_cpub_clk = {
+	.data = &(struct clk_regmap_mux_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL,
+		.mask = 0x1,
+		.shift = 11,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk",
+		.ops = &clk_regmap_mux_ro_ops,
+		.parent_names = (const char *[]){ "cpub_clk_dyn",
+						  "sys_pll" },
+		.num_parents = 2,
+	},
+};
+
 static struct clk_regmap g12a_cpu_clk_div16_en = {
 	.data = &(struct clk_regmap_gate_data){
 		.offset = HHI_SYS_CPU_CLK_CNTL1,
@@ -323,6 +546,23 @@ static struct clk_regmap g12a_cpu_clk_div16_en = {
 	},
 };
 
+static struct clk_regmap g12b_cpub_clk_div16_en = {
+	.data = &(struct clk_regmap_gate_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL1,
+		.bit_idx = 1,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "cpub_clk_div16_en",
+		.ops = &clk_regmap_gate_ro_ops,
+		.parent_names = (const char *[]){ "cpub_clk" },
+		.num_parents = 1,
+		/*
+		 * This clock is used to debug the cpu_clk range
+		 * Linux should not change it at runtime
+		 */
+	},
+};
+
 static struct clk_fixed_factor g12a_cpu_clk_div16 = {
 	.mult = 1,
 	.div = 16,
@@ -334,6 +574,17 @@ static struct clk_fixed_factor g12a_cpu_clk_div16 = {
 	},
 };
 
+static struct clk_fixed_factor g12b_cpub_clk_div16 = {
+	.mult = 1,
+	.div = 16,
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_div16",
+		.ops = &clk_fixed_factor_ops,
+		.parent_names = (const char *[]){ "cpub_clk_div16_en" },
+		.num_parents = 1,
+	},
+};
+
 static struct clk_regmap g12a_cpu_clk_apb_div = {
 	.data = &(struct clk_regmap_div_data){
 		.offset = HHI_SYS_CPU_CLK_CNTL1,
@@ -462,6 +713,240 @@ static struct clk_regmap g12a_cpu_clk_trace = {
 	},
 };
 
+static struct clk_fixed_factor g12b_cpub_clk_div2 = {
+	.mult = 1,
+	.div = 2,
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_div2",
+		.ops = &clk_fixed_factor_ops,
+		.parent_names = (const char *[]){ "cpub_clk" },
+		.num_parents = 1,
+	},
+};
+
+static struct clk_fixed_factor g12b_cpub_clk_div3 = {
+	.mult = 1,
+	.div = 3,
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_div3",
+		.ops = &clk_fixed_factor_ops,
+		.parent_names = (const char *[]){ "cpub_clk" },
+		.num_parents = 1,
+	},
+};
+
+static struct clk_fixed_factor g12b_cpub_clk_div4 = {
+	.mult = 1,
+	.div = 4,
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_div4",
+		.ops = &clk_fixed_factor_ops,
+		.parent_names = (const char *[]){ "cpub_clk" },
+		.num_parents = 1,
+	},
+};
+
+static struct clk_fixed_factor g12b_cpub_clk_div5 = {
+	.mult = 1,
+	.div = 5,
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_div5",
+		.ops = &clk_fixed_factor_ops,
+		.parent_names = (const char *[]){ "cpub_clk" },
+		.num_parents = 1,
+	},
+};
+
+static struct clk_fixed_factor g12b_cpub_clk_div6 = {
+	.mult = 1,
+	.div = 6,
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_div6",
+		.ops = &clk_fixed_factor_ops,
+		.parent_names = (const char *[]){ "cpub_clk" },
+		.num_parents = 1,
+	},
+};
+
+static struct clk_fixed_factor g12b_cpub_clk_div7 = {
+	.mult = 1,
+	.div = 7,
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_div7",
+		.ops = &clk_fixed_factor_ops,
+		.parent_names = (const char *[]){ "cpub_clk" },
+		.num_parents = 1,
+	},
+};
+
+static struct clk_fixed_factor g12b_cpub_clk_div8 = {
+	.mult = 1,
+	.div = 8,
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_div8",
+		.ops = &clk_fixed_factor_ops,
+		.parent_names = (const char *[]){ "cpub_clk" },
+		.num_parents = 1,
+	},
+};
+
+static u32 mux_table_cpub[] = { 1, 2, 3, 4, 5, 6, 7 };
+static struct clk_regmap g12b_cpub_clk_apb_sel = {
+	.data = &(struct clk_regmap_mux_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL1,
+		.mask = 7,
+		.shift = 3,
+		.table = mux_table_cpub,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_apb_sel",
+		.ops = &clk_regmap_mux_ro_ops,
+		.parent_names = (const char *[]){ "cpub_clk_div2",
+						  "cpub_clk_div3",
+						  "cpub_clk_div4",
+						  "cpub_clk_div5",
+						  "cpub_clk_div6",
+						  "cpub_clk_div7",
+						  "cpub_clk_div8" },
+		.num_parents = 7,
+	},
+};
+
+static struct clk_regmap g12b_cpub_clk_apb = {
+	.data = &(struct clk_regmap_gate_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL1,
+		.bit_idx = 16,
+		.flags = CLK_GATE_SET_TO_DISABLE,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "cpub_clk_apb",
+		.ops = &clk_regmap_gate_ro_ops,
+		.parent_names = (const char *[]){ "cpub_clk_apb_sel" },
+		.num_parents = 1,
+		/*
+		 * This clock is set by the ROM monitor code,
+		 * Linux should not change it at runtime
+		 */
+	},
+};
+
+static struct clk_regmap g12b_cpub_clk_atb_sel = {
+	.data = &(struct clk_regmap_mux_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL1,
+		.mask = 7,
+		.shift = 6,
+		.table = mux_table_cpub,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_atb_sel",
+		.ops = &clk_regmap_mux_ro_ops,
+		.parent_names = (const char *[]){ "cpub_clk_div2",
+						  "cpub_clk_div3",
+						  "cpub_clk_div4",
+						  "cpub_clk_div5",
+						  "cpub_clk_div6",
+						  "cpub_clk_div7",
+						  "cpub_clk_div8" },
+		.num_parents = 7,
+	},
+};
+
+static struct clk_regmap g12b_cpub_clk_atb = {
+	.data = &(struct clk_regmap_gate_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL1,
+		.bit_idx = 17,
+		.flags = CLK_GATE_SET_TO_DISABLE,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "cpub_clk_atb",
+		.ops = &clk_regmap_gate_ro_ops,
+		.parent_names = (const char *[]){ "cpub_clk_atb_sel" },
+		.num_parents = 1,
+		/*
+		 * This clock is set by the ROM monitor code,
+		 * Linux should not change it at runtime
+		 */
+	},
+};
+
+static struct clk_regmap g12b_cpub_clk_axi_sel = {
+	.data = &(struct clk_regmap_mux_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL1,
+		.mask = 7,
+		.shift = 9,
+		.table = mux_table_cpub,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_axi_sel",
+		.ops = &clk_regmap_mux_ro_ops,
+		.parent_names = (const char *[]){ "cpub_clk_div2",
+						  "cpub_clk_div3",
+						  "cpub_clk_div4",
+						  "cpub_clk_div5",
+						  "cpub_clk_div6",
+						  "cpub_clk_div7",
+						  "cpub_clk_div8" },
+		.num_parents = 7,
+	},
+};
+
+static struct clk_regmap g12b_cpub_clk_axi = {
+	.data = &(struct clk_regmap_gate_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL1,
+		.bit_idx = 18,
+		.flags = CLK_GATE_SET_TO_DISABLE,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "cpub_clk_axi",
+		.ops = &clk_regmap_gate_ro_ops,
+		.parent_names = (const char *[]){ "cpub_clk_axi_sel" },
+		.num_parents = 1,
+		/*
+		 * This clock is set by the ROM monitor code,
+		 * Linux should not change it at runtime
+		 */
+	},
+};
+
+static struct clk_regmap g12b_cpub_clk_trace_sel = {
+	.data = &(struct clk_regmap_mux_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL1,
+		.mask = 7,
+		.shift = 20,
+		.table = mux_table_cpub,
+	},
+	.hw.init = &(struct clk_init_data){
+		.name = "cpub_clk_trace_sel",
+		.ops = &clk_regmap_mux_ro_ops,
+		.parent_names = (const char *[]){ "cpub_clk_div2",
+						  "cpub_clk_div3",
+						  "cpub_clk_div4",
+						  "cpub_clk_div5",
+						  "cpub_clk_div6",
+						  "cpub_clk_div7",
+						  "cpub_clk_div8" },
+		.num_parents = 7,
+	},
+};
+
+static struct clk_regmap g12b_cpub_clk_trace = {
+	.data = &(struct clk_regmap_gate_data){
+		.offset = HHI_SYS_CPUB_CLK_CNTL1,
+		.bit_idx = 23,
+		.flags = CLK_GATE_SET_TO_DISABLE,
+	},
+	.hw.init = &(struct clk_init_data) {
+		.name = "cpub_clk_trace",
+		.ops = &clk_regmap_gate_ro_ops,
+		.parent_names = (const char *[]){ "cpub_clk_trace_sel" },
+		.num_parents = 1,
+		/*
+		 * This clock is set by the ROM monitor code,
+		 * Linux should not change it at runtime
+		 */
+	},
+};
+
 static const struct pll_mult_range g12a_gp0_pll_mult_range = {
 	.min = 125,
 	.max = 255,
@@ -2827,6 +3312,255 @@ static struct clk_hw_onecell_data g12a_hw_onecell_data = {
 	.num = NR_CLKS,
 };
 
+static struct clk_hw_onecell_data g12b_hw_onecell_data = {
+	.hws = {
+		[CLKID_SYS_PLL]			= &g12a_sys_pll.hw,
+		[CLKID_FIXED_PLL]		= &g12a_fixed_pll.hw,
+		[CLKID_FCLK_DIV2]		= &g12a_fclk_div2.hw,
+		[CLKID_FCLK_DIV3]		= &g12a_fclk_div3.hw,
+		[CLKID_FCLK_DIV4]		= &g12a_fclk_div4.hw,
+		[CLKID_FCLK_DIV5]		= &g12a_fclk_div5.hw,
+		[CLKID_FCLK_DIV7]		= &g12a_fclk_div7.hw,
+		[CLKID_FCLK_DIV2P5]		= &g12a_fclk_div2p5.hw,
+		[CLKID_GP0_PLL]			= &g12a_gp0_pll.hw,
+		[CLKID_MPEG_SEL]		= &g12a_mpeg_clk_sel.hw,
+		[CLKID_MPEG_DIV]		= &g12a_mpeg_clk_div.hw,
+		[CLKID_CLK81]			= &g12a_clk81.hw,
+		[CLKID_MPLL0]			= &g12a_mpll0.hw,
+		[CLKID_MPLL1]			= &g12a_mpll1.hw,
+		[CLKID_MPLL2]			= &g12a_mpll2.hw,
+		[CLKID_MPLL3]			= &g12a_mpll3.hw,
+		[CLKID_DDR]			= &g12a_ddr.hw,
+		[CLKID_DOS]			= &g12a_dos.hw,
+		[CLKID_AUDIO_LOCKER]		= &g12a_audio_locker.hw,
+		[CLKID_MIPI_DSI_HOST]		= &g12a_mipi_dsi_host.hw,
+		[CLKID_ETH_PHY]			= &g12a_eth_phy.hw,
+		[CLKID_ISA]			= &g12a_isa.hw,
+		[CLKID_PL301]			= &g12a_pl301.hw,
+		[CLKID_PERIPHS]			= &g12a_periphs.hw,
+		[CLKID_SPICC0]			= &g12a_spicc_0.hw,
+		[CLKID_I2C]			= &g12a_i2c.hw,
+		[CLKID_SANA]			= &g12a_sana.hw,
+		[CLKID_SD]			= &g12a_sd.hw,
+		[CLKID_RNG0]			= &g12a_rng0.hw,
+		[CLKID_UART0]			= &g12a_uart0.hw,
+		[CLKID_SPICC1]			= &g12a_spicc_1.hw,
+		[CLKID_HIU_IFACE]		= &g12a_hiu_reg.hw,
+		[CLKID_MIPI_DSI_PHY]		= &g12a_mipi_dsi_phy.hw,
+		[CLKID_ASSIST_MISC]		= &g12a_assist_misc.hw,
+		[CLKID_SD_EMMC_A]		= &g12a_emmc_a.hw,
+		[CLKID_SD_EMMC_B]		= &g12a_emmc_b.hw,
+		[CLKID_SD_EMMC_C]		= &g12a_emmc_c.hw,
+		[CLKID_AUDIO_CODEC]		= &g12a_audio_codec.hw,
+		[CLKID_AUDIO]			= &g12a_audio.hw,
+		[CLKID_ETH]			= &g12a_eth_core.hw,
+		[CLKID_DEMUX]			= &g12a_demux.hw,
+		[CLKID_AUDIO_IFIFO]		= &g12a_audio_ififo.hw,
+		[CLKID_ADC]			= &g12a_adc.hw,
+		[CLKID_UART1]			= &g12a_uart1.hw,
+		[CLKID_G2D]			= &g12a_g2d.hw,
+		[CLKID_RESET]			= &g12a_reset.hw,
+		[CLKID_PCIE_COMB]		= &g12a_pcie_comb.hw,
+		[CLKID_PARSER]			= &g12a_parser.hw,
+		[CLKID_USB]			= &g12a_usb_general.hw,
+		[CLKID_PCIE_PHY]		= &g12a_pcie_phy.hw,
+		[CLKID_AHB_ARB0]		= &g12a_ahb_arb0.hw,
+		[CLKID_AHB_DATA_BUS]		= &g12a_ahb_data_bus.hw,
+		[CLKID_AHB_CTRL_BUS]		= &g12a_ahb_ctrl_bus.hw,
+		[CLKID_HTX_HDCP22]		= &g12a_htx_hdcp22.hw,
+		[CLKID_HTX_PCLK]		= &g12a_htx_pclk.hw,
+		[CLKID_BT656]			= &g12a_bt656.hw,
+		[CLKID_USB1_DDR_BRIDGE]		= &g12a_usb1_to_ddr.hw,
+		[CLKID_MMC_PCLK]		= &g12a_mmc_pclk.hw,
+		[CLKID_UART2]			= &g12a_uart2.hw,
+		[CLKID_VPU_INTR]		= &g12a_vpu_intr.hw,
+		[CLKID_GIC]			= &g12a_gic.hw,
+		[CLKID_SD_EMMC_A_CLK0_SEL]	= &g12a_sd_emmc_a_clk0_sel.hw,
+		[CLKID_SD_EMMC_A_CLK0_DIV]	= &g12a_sd_emmc_a_clk0_div.hw,
+		[CLKID_SD_EMMC_A_CLK0]		= &g12a_sd_emmc_a_clk0.hw,
+		[CLKID_SD_EMMC_B_CLK0_SEL]	= &g12a_sd_emmc_b_clk0_sel.hw,
+		[CLKID_SD_EMMC_B_CLK0_DIV]	= &g12a_sd_emmc_b_clk0_div.hw,
+		[CLKID_SD_EMMC_B_CLK0]		= &g12a_sd_emmc_b_clk0.hw,
+		[CLKID_SD_EMMC_C_CLK0_SEL]	= &g12a_sd_emmc_c_clk0_sel.hw,
+		[CLKID_SD_EMMC_C_CLK0_DIV]	= &g12a_sd_emmc_c_clk0_div.hw,
+		[CLKID_SD_EMMC_C_CLK0]		= &g12a_sd_emmc_c_clk0.hw,
+		[CLKID_MPLL0_DIV]		= &g12a_mpll0_div.hw,
+		[CLKID_MPLL1_DIV]		= &g12a_mpll1_div.hw,
+		[CLKID_MPLL2_DIV]		= &g12a_mpll2_div.hw,
+		[CLKID_MPLL3_DIV]		= &g12a_mpll3_div.hw,
+		[CLKID_FCLK_DIV2_DIV]		= &g12a_fclk_div2_div.hw,
+		[CLKID_FCLK_DIV3_DIV]		= &g12a_fclk_div3_div.hw,
+		[CLKID_FCLK_DIV4_DIV]		= &g12a_fclk_div4_div.hw,
+		[CLKID_FCLK_DIV5_DIV]		= &g12a_fclk_div5_div.hw,
+		[CLKID_FCLK_DIV7_DIV]		= &g12a_fclk_div7_div.hw,
+		[CLKID_FCLK_DIV2P5_DIV]		= &g12a_fclk_div2p5_div.hw,
+		[CLKID_HIFI_PLL]		= &g12a_hifi_pll.hw,
+		[CLKID_VCLK2_VENCI0]		= &g12a_vclk2_venci0.hw,
+		[CLKID_VCLK2_VENCI1]		= &g12a_vclk2_venci1.hw,
+		[CLKID_VCLK2_VENCP0]		= &g12a_vclk2_vencp0.hw,
+		[CLKID_VCLK2_VENCP1]		= &g12a_vclk2_vencp1.hw,
+		[CLKID_VCLK2_VENCT0]		= &g12a_vclk2_venct0.hw,
+		[CLKID_VCLK2_VENCT1]		= &g12a_vclk2_venct1.hw,
+		[CLKID_VCLK2_OTHER]		= &g12a_vclk2_other.hw,
+		[CLKID_VCLK2_ENCI]		= &g12a_vclk2_enci.hw,
+		[CLKID_VCLK2_ENCP]		= &g12a_vclk2_encp.hw,
+		[CLKID_DAC_CLK]			= &g12a_dac_clk.hw,
+		[CLKID_AOCLK]			= &g12a_aoclk_gate.hw,
+		[CLKID_IEC958]			= &g12a_iec958_gate.hw,
+		[CLKID_ENC480P]			= &g12a_enc480p.hw,
+		[CLKID_RNG1]			= &g12a_rng1.hw,
+		[CLKID_VCLK2_ENCT]		= &g12a_vclk2_enct.hw,
+		[CLKID_VCLK2_ENCL]		= &g12a_vclk2_encl.hw,
+		[CLKID_VCLK2_VENCLMMC]		= &g12a_vclk2_venclmmc.hw,
+		[CLKID_VCLK2_VENCL]		= &g12a_vclk2_vencl.hw,
+		[CLKID_VCLK2_OTHER1]		= &g12a_vclk2_other1.hw,
+		[CLKID_FIXED_PLL_DCO]		= &g12a_fixed_pll_dco.hw,
+		[CLKID_SYS_PLL_DCO]		= &g12a_sys_pll_dco.hw,
+		[CLKID_GP0_PLL_DCO]		= &g12a_gp0_pll_dco.hw,
+		[CLKID_HIFI_PLL_DCO]		= &g12a_hifi_pll_dco.hw,
+		[CLKID_DMA]			= &g12a_dma.hw,
+		[CLKID_EFUSE]			= &g12a_efuse.hw,
+		[CLKID_ROM_BOOT]		= &g12a_rom_boot.hw,
+		[CLKID_RESET_SEC]		= &g12a_reset_sec.hw,
+		[CLKID_SEC_AHB_APB3]		= &g12a_sec_ahb_apb3.hw,
+		[CLKID_MPLL_PREDIV]		= &g12a_mpll_prediv.hw,
+		[CLKID_VPU_0_SEL]		= &g12a_vpu_0_sel.hw,
+		[CLKID_VPU_0_DIV]		= &g12a_vpu_0_div.hw,
+		[CLKID_VPU_0]			= &g12a_vpu_0.hw,
+		[CLKID_VPU_1_SEL]		= &g12a_vpu_1_sel.hw,
+		[CLKID_VPU_1_DIV]		= &g12a_vpu_1_div.hw,
+		[CLKID_VPU_1]			= &g12a_vpu_1.hw,
+		[CLKID_VPU]			= &g12a_vpu.hw,
+		[CLKID_VAPB_0_SEL]		= &g12a_vapb_0_sel.hw,
+		[CLKID_VAPB_0_DIV]		= &g12a_vapb_0_div.hw,
+		[CLKID_VAPB_0]			= &g12a_vapb_0.hw,
+		[CLKID_VAPB_1_SEL]		= &g12a_vapb_1_sel.hw,
+		[CLKID_VAPB_1_DIV]		= &g12a_vapb_1_div.hw,
+		[CLKID_VAPB_1]			= &g12a_vapb_1.hw,
+		[CLKID_VAPB_SEL]		= &g12a_vapb_sel.hw,
+		[CLKID_VAPB]			= &g12a_vapb.hw,
+		[CLKID_HDMI_PLL_DCO]		= &g12a_hdmi_pll_dco.hw,
+		[CLKID_HDMI_PLL_OD]		= &g12a_hdmi_pll_od.hw,
+		[CLKID_HDMI_PLL_OD2]		= &g12a_hdmi_pll_od2.hw,
+		[CLKID_HDMI_PLL]		= &g12a_hdmi_pll.hw,
+		[CLKID_VID_PLL]			= &g12a_vid_pll_div.hw,
+		[CLKID_VID_PLL_SEL]		= &g12a_vid_pll_sel.hw,
+		[CLKID_VID_PLL_DIV]		= &g12a_vid_pll.hw,
+		[CLKID_VCLK_SEL]		= &g12a_vclk_sel.hw,
+		[CLKID_VCLK2_SEL]		= &g12a_vclk2_sel.hw,
+		[CLKID_VCLK_INPUT]		= &g12a_vclk_input.hw,
+		[CLKID_VCLK2_INPUT]		= &g12a_vclk2_input.hw,
+		[CLKID_VCLK_DIV]		= &g12a_vclk_div.hw,
+		[CLKID_VCLK2_DIV]		= &g12a_vclk2_div.hw,
+		[CLKID_VCLK]			= &g12a_vclk.hw,
+		[CLKID_VCLK2]			= &g12a_vclk2.hw,
+		[CLKID_VCLK_DIV1]		= &g12a_vclk_div1.hw,
+		[CLKID_VCLK_DIV2_EN]		= &g12a_vclk_div2_en.hw,
+		[CLKID_VCLK_DIV4_EN]		= &g12a_vclk_div4_en.hw,
+		[CLKID_VCLK_DIV6_EN]		= &g12a_vclk_div6_en.hw,
+		[CLKID_VCLK_DIV12_EN]		= &g12a_vclk_div12_en.hw,
+		[CLKID_VCLK2_DIV1]		= &g12a_vclk2_div1.hw,
+		[CLKID_VCLK2_DIV2_EN]		= &g12a_vclk2_div2_en.hw,
+		[CLKID_VCLK2_DIV4_EN]		= &g12a_vclk2_div4_en.hw,
+		[CLKID_VCLK2_DIV6_EN]		= &g12a_vclk2_div6_en.hw,
+		[CLKID_VCLK2_DIV12_EN]		= &g12a_vclk2_div12_en.hw,
+		[CLKID_VCLK_DIV2]		= &g12a_vclk_div2.hw,
+		[CLKID_VCLK_DIV4]		= &g12a_vclk_div4.hw,
+		[CLKID_VCLK_DIV6]		= &g12a_vclk_div6.hw,
+		[CLKID_VCLK_DIV12]		= &g12a_vclk_div12.hw,
+		[CLKID_VCLK2_DIV2]		= &g12a_vclk2_div2.hw,
+		[CLKID_VCLK2_DIV4]		= &g12a_vclk2_div4.hw,
+		[CLKID_VCLK2_DIV6]		= &g12a_vclk2_div6.hw,
+		[CLKID_VCLK2_DIV12]		= &g12a_vclk2_div12.hw,
+		[CLKID_CTS_ENCI_SEL]		= &g12a_cts_enci_sel.hw,
+		[CLKID_CTS_ENCP_SEL]		= &g12a_cts_encp_sel.hw,
+		[CLKID_CTS_VDAC_SEL]		= &g12a_cts_vdac_sel.hw,
+		[CLKID_HDMI_TX_SEL]		= &g12a_hdmi_tx_sel.hw,
+		[CLKID_CTS_ENCI]		= &g12a_cts_enci.hw,
+		[CLKID_CTS_ENCP]		= &g12a_cts_encp.hw,
+		[CLKID_CTS_VDAC]		= &g12a_cts_vdac.hw,
+		[CLKID_HDMI_TX]			= &g12a_hdmi_tx.hw,
+		[CLKID_HDMI_SEL]		= &g12a_hdmi_sel.hw,
+		[CLKID_HDMI_DIV]		= &g12a_hdmi_div.hw,
+		[CLKID_HDMI]			= &g12a_hdmi.hw,
+		[CLKID_MALI_0_SEL]		= &g12a_mali_0_sel.hw,
+		[CLKID_MALI_0_DIV]		= &g12a_mali_0_div.hw,
+		[CLKID_MALI_0]			= &g12a_mali_0.hw,
+		[CLKID_MALI_1_SEL]		= &g12a_mali_1_sel.hw,
+		[CLKID_MALI_1_DIV]		= &g12a_mali_1_div.hw,
+		[CLKID_MALI_1]			= &g12a_mali_1.hw,
+		[CLKID_MALI]			= &g12a_mali.hw,
+		[CLKID_MPLL_50M_DIV]		= &g12a_mpll_50m_div.hw,
+		[CLKID_MPLL_50M]		= &g12a_mpll_50m.hw,
+		[CLKID_SYS_PLL_DIV16_EN]	= &g12a_sys_pll_div16_en.hw,
+		[CLKID_SYS_PLL_DIV16]		= &g12a_sys_pll_div16.hw,
+		[CLKID_CPU_CLK_DYN0_SEL]	= &g12a_cpu_clk_premux0.hw,
+		[CLKID_CPU_CLK_DYN0_DIV]	= &g12a_cpu_clk_mux0_div.hw,
+		[CLKID_CPU_CLK_DYN0]		= &g12a_cpu_clk_postmux0.hw,
+		[CLKID_CPU_CLK_DYN1_SEL]	= &g12a_cpu_clk_premux1.hw,
+		[CLKID_CPU_CLK_DYN1_DIV]	= &g12a_cpu_clk_mux1_div.hw,
+		[CLKID_CPU_CLK_DYN1]		= &g12a_cpu_clk_postmux1.hw,
+		[CLKID_CPU_CLK_DYN]		= &g12a_cpu_clk_dyn.hw,
+		[CLKID_CPU_CLK]			= &g12b_cpu_clk.hw,
+		[CLKID_CPU_CLK_DIV16_EN]	= &g12a_cpu_clk_div16_en.hw,
+		[CLKID_CPU_CLK_DIV16]		= &g12a_cpu_clk_div16.hw,
+		[CLKID_CPU_CLK_APB_DIV]		= &g12a_cpu_clk_apb_div.hw,
+		[CLKID_CPU_CLK_APB]		= &g12a_cpu_clk_apb.hw,
+		[CLKID_CPU_CLK_ATB_DIV]		= &g12a_cpu_clk_atb_div.hw,
+		[CLKID_CPU_CLK_ATB]		= &g12a_cpu_clk_atb.hw,
+		[CLKID_CPU_CLK_AXI_DIV]		= &g12a_cpu_clk_axi_div.hw,
+		[CLKID_CPU_CLK_AXI]		= &g12a_cpu_clk_axi.hw,
+		[CLKID_CPU_CLK_TRACE_DIV]	= &g12a_cpu_clk_trace_div.hw,
+		[CLKID_CPU_CLK_TRACE]		= &g12a_cpu_clk_trace.hw,
+		[CLKID_PCIE_PLL_DCO]		= &g12a_pcie_pll_dco.hw,
+		[CLKID_PCIE_PLL_DCO_DIV2]	= &g12a_pcie_pll_dco_div2.hw,
+		[CLKID_PCIE_PLL_OD]		= &g12a_pcie_pll_od.hw,
+		[CLKID_PCIE_PLL]		= &g12a_pcie_pll.hw,
+		[CLKID_VDEC_1_SEL]		= &g12a_vdec_1_sel.hw,
+		[CLKID_VDEC_1_DIV]		= &g12a_vdec_1_div.hw,
+		[CLKID_VDEC_1]			= &g12a_vdec_1.hw,
+		[CLKID_VDEC_HEVC_SEL]		= &g12a_vdec_hevc_sel.hw,
+		[CLKID_VDEC_HEVC_DIV]		= &g12a_vdec_hevc_div.hw,
+		[CLKID_VDEC_HEVC]		= &g12a_vdec_hevc.hw,
+		[CLKID_VDEC_HEVCF_SEL]		= &g12a_vdec_hevcf_sel.hw,
+		[CLKID_VDEC_HEVCF_DIV]		= &g12a_vdec_hevcf_div.hw,
+		[CLKID_VDEC_HEVCF]		= &g12a_vdec_hevcf.hw,
+		[CLKID_TS_DIV]			= &g12a_ts_div.hw,
+		[CLKID_TS]			= &g12a_ts.hw,
+		[CLKID_SYS1_PLL_DCO]		= &g12b_sys1_pll_dco.hw,
+		[CLKID_SYS1_PLL]		= &g12b_sys1_pll.hw,
+		[CLKID_SYS1_PLL_DIV16_EN]	= &g12b_sys1_pll_div16_en.hw,
+		[CLKID_SYS1_PLL_DIV16]		= &g12b_sys1_pll_div16.hw,
+		[CLKID_CPUB_CLK_DYN0_SEL]	= &g12b_cpub_clk_premux0.hw,
+		[CLKID_CPUB_CLK_DYN0_DIV]	= &g12b_cpub_clk_mux0_div.hw,
+		[CLKID_CPUB_CLK_DYN0]		= &g12b_cpub_clk_postmux0.hw,
+		[CLKID_CPUB_CLK_DYN1_SEL]	= &g12b_cpub_clk_premux1.hw,
+		[CLKID_CPUB_CLK_DYN1_DIV]	= &g12b_cpub_clk_mux1_div.hw,
+		[CLKID_CPUB_CLK_DYN1]		= &g12b_cpub_clk_postmux1.hw,
+		[CLKID_CPUB_CLK_DYN]		= &g12b_cpub_clk_dyn.hw,
+		[CLKID_CPUB_CLK]		= &g12b_cpub_clk.hw,
+		[CLKID_CPUB_CLK_DIV16_EN]	= &g12b_cpub_clk_div16_en.hw,
+		[CLKID_CPUB_CLK_DIV16]		= &g12b_cpub_clk_div16.hw,
+		[CLKID_CPUB_CLK_DIV2]		= &g12b_cpub_clk_div2.hw,
+		[CLKID_CPUB_CLK_DIV3]		= &g12b_cpub_clk_div3.hw,
+		[CLKID_CPUB_CLK_DIV4]		= &g12b_cpub_clk_div4.hw,
+		[CLKID_CPUB_CLK_DIV5]		= &g12b_cpub_clk_div5.hw,
+		[CLKID_CPUB_CLK_DIV6]		= &g12b_cpub_clk_div6.hw,
+		[CLKID_CPUB_CLK_DIV7]		= &g12b_cpub_clk_div7.hw,
+		[CLKID_CPUB_CLK_DIV8]		= &g12b_cpub_clk_div8.hw,
+		[CLKID_CPUB_CLK_APB_SEL]	= &g12b_cpub_clk_apb_sel.hw,
+		[CLKID_CPUB_CLK_APB]		= &g12b_cpub_clk_apb.hw,
+		[CLKID_CPUB_CLK_ATB_SEL]	= &g12b_cpub_clk_atb_sel.hw,
+		[CLKID_CPUB_CLK_ATB]		= &g12b_cpub_clk_atb.hw,
+		[CLKID_CPUB_CLK_AXI_SEL]	= &g12b_cpub_clk_axi_sel.hw,
+		[CLKID_CPUB_CLK_AXI]		= &g12b_cpub_clk_axi.hw,
+		[CLKID_CPUB_CLK_TRACE_SEL]	= &g12b_cpub_clk_trace_sel.hw,
+		[CLKID_CPUB_CLK_TRACE]		= &g12b_cpub_clk_trace.hw,
+		[NR_CLKS]			= NULL,
+	},
+	.num = NR_CLKS,
+};
+
 /* Convenience table to populate regmap in .probe */
 static struct clk_regmap *const g12a_clk_regmaps[] = {
 	&g12a_clk81,
@@ -3021,6 +3755,27 @@ static struct clk_regmap *const g12a_clk_regmaps[] = {
 	&g12a_vdec_hevcf,
 	&g12a_ts_div,
 	&g12a_ts,
+	&g12b_cpu_clk,
+	&g12b_sys1_pll_dco,
+	&g12b_sys1_pll,
+	&g12b_sys1_pll_div16_en,
+	&g12b_cpub_clk_premux0,
+	&g12b_cpub_clk_mux0_div,
+	&g12b_cpub_clk_postmux0,
+	&g12b_cpub_clk_premux1,
+	&g12b_cpub_clk_mux1_div,
+	&g12b_cpub_clk_postmux1,
+	&g12b_cpub_clk_dyn,
+	&g12b_cpub_clk,
+	&g12b_cpub_clk_div16_en,
+	&g12b_cpub_clk_apb_sel,
+	&g12b_cpub_clk_apb,
+	&g12b_cpub_clk_atb_sel,
+	&g12b_cpub_clk_atb,
+	&g12b_cpub_clk_axi_sel,
+	&g12b_cpub_clk_axi,
+	&g12b_cpub_clk_trace_sel,
+	&g12b_cpub_clk_trace,
 };
 
 static const struct reg_sequence g12a_init_regs[] = {
@@ -3035,8 +3790,15 @@ static const struct meson_eeclkc_data g12a_clkc_data = {
 	.init_count = ARRAY_SIZE(g12a_init_regs),
 };
 
+static const struct meson_eeclkc_data g12b_clkc_data = {
+	.regmap_clks = g12a_clk_regmaps,
+	.regmap_clk_num = ARRAY_SIZE(g12a_clk_regmaps),
+	.hw_onecell_data = &g12b_hw_onecell_data
+};
+
 static const struct of_device_id clkc_match_table[] = {
 	{ .compatible = "amlogic,g12a-clkc", .data = &g12a_clkc_data },
+	{ .compatible = "amlogic,g12b-clkc", .data = &g12b_clkc_data },
 	{}
 };
 
drivers/clk/meson/g12a.h +39 -1
index bda1501ba671..c8aed31fbe17 100644
@@ -69,6 +69,8 @@
 #define HHI_VDEC4_CLK_CNTL		0x1EC
 #define HHI_HDCP22_CLK_CNTL		0x1F0
 #define HHI_VAPBCLK_CNTL		0x1F4
+#define HHI_SYS_CPUB_CLK_CNTL1		0x200
+#define HHI_SYS_CPUB_CLK_CNTL		0x208
 #define HHI_VPU_CLKB_CNTL		0x20C
 #define HHI_GEN_CLK_CNTL		0x228
 #define HHI_VDIN_MEAS_CLK_CNTL		0x250
@@ -102,6 +104,13 @@
 #define HHI_HDMI_PLL_CNTL5		0x334
 #define HHI_HDMI_PLL_CNTL6		0x338
 #define HHI_SPICC_CLK_CNTL		0x3dc
+#define HHI_SYS1_PLL_CNTL0		0x380
+#define HHI_SYS1_PLL_CNTL1		0x384
+#define HHI_SYS1_PLL_CNTL2		0x388
+#define HHI_SYS1_PLL_CNTL3		0x38c
+#define HHI_SYS1_PLL_CNTL4		0x390
+#define HHI_SYS1_PLL_CNTL5		0x394
+#define HHI_SYS1_PLL_CNTL6		0x398
 
 /*
  * CLKID index values
@@ -196,8 +205,37 @@
 #define CLKID_VDEC_HEVCF_SEL			208
 #define CLKID_VDEC_HEVCF_DIV			209
 #define CLKID_TS_DIV				211
+#define CLKID_SYS1_PLL_DCO			213
+#define CLKID_SYS1_PLL				214
+#define CLKID_SYS1_PLL_DIV16_EN			215
+#define CLKID_SYS1_PLL_DIV16			216
+#define CLKID_CPUB_CLK_DYN0_SEL			217
+#define CLKID_CPUB_CLK_DYN0_DIV			218
+#define CLKID_CPUB_CLK_DYN0			219
+#define CLKID_CPUB_CLK_DYN1_SEL			220
+#define CLKID_CPUB_CLK_DYN1_DIV			221
+#define CLKID_CPUB_CLK_DYN1			222
+#define CLKID_CPUB_CLK_DYN			223
+#define CLKID_CPUB_CLK				224
+#define CLKID_CPUB_CLK_DIV16_EN			225
+#define CLKID_CPUB_CLK_DIV16			226
+#define CLKID_CPUB_CLK_DIV2			227
+#define CLKID_CPUB_CLK_DIV3			228
+#define CLKID_CPUB_CLK_DIV4			229
+#define CLKID_CPUB_CLK_DIV5			230
+#define CLKID_CPUB_CLK_DIV6			231
+#define CLKID_CPUB_CLK_DIV7			232
+#define CLKID_CPUB_CLK_DIV8			233
+#define CLKID_CPUB_CLK_APB_SEL			234
+#define CLKID_CPUB_CLK_APB			235
+#define CLKID_CPUB_CLK_ATB_SEL			236
+#define CLKID_CPUB_CLK_ATB			237
+#define CLKID_CPUB_CLK_AXI_SEL			238
+#define CLKID_CPUB_CLK_AXI			239
+#define CLKID_CPUB_CLK_TRACE_SEL		240
+#define CLKID_CPUB_CLK_TRACE			241
 
-#define NR_CLKS					213
+#define NR_CLKS					242
 
 /* include the CLKIDs that have been made part of the DT binding */
 #include <dt-bindings/clock/g12a-clkc.h>
Signature · 1 line
2.21.0
reviewer Reviewed-by on v2 2/3
#3 lore raw

Re: [PATCH v2 2/3] clk: meson: g12a: Add support for G12B CPUB clocks

Hi Neil,

Quoted 11 lines · Neil Armstrong

Update the Meson G12A Clock driver to support the Amlogic G12B SoC.

G12B clock driver is very close, the main differences are :
- the clock tree is duplicated for the both clusters, and the SYS_PLL are swapped between the clusters
- G12B has additional clocks like for CSI an other components

Here only the cpu clock tree is handled.

thank you for taking care of everything I noticed in the previous version!

do you still have the CPU post-divider muxes (which are currently modeled as CLK_DIVIDER_POWER_OF_TWO dividers) on your TODO-list once this is merged?

Martin

#4 lore raw

Re: [PATCH v2 2/3] clk: meson: g12a: Add support for G12B CPUB clocks

Quoted 13 lines · Martin Blumenstingl

Hi Neil,

Quoted 10 lines · Neil Armstrong

Update the Meson G12A Clock driver to support the Amlogic G12B SoC.

G12B clock driver is very close, the main differences are :
- the clock tree is duplicated for the both clusters, and the SYS_PLL are swapped between the clusters
- G12B has additional clocks like for CSI an other components

Here only the cpu clock tree is handled.

Quoted 7 lines
Quoted 1 line

thank you for taking care of everything I noticed in the previous version!

do you still have the CPU post-divider muxes (which are currently modeled as CLK_DIVIDER_POWER_OF_TWO dividers) on your TODO-list once this is merged?

Yes, thanks for reviewing !

Neil

Quoted 4 lines

Martin

#5 lore raw

PATCH v2 3/3 clk: meson: g12a: mark fclk_div3 as critical

In reply to Neil Armstrong

On Amlogic Meson G12b platform, the fclk_div3 seems to be necessary for the system to operate correctly.

Disabling it cause the entire system to freeze, including peripherals.

Let's mark this clock as critical, fixing boot on G12b platforms.

---
 drivers/clk/meson/g12a.c | 10 ++++++++++
 1 file changed, 10 insertions(+)
drivers/clk/meson/g12a.c +10 -0
index 1abe46a95dc1..3c75ef5e4d24 100644
@@ -1350,6 +1350,16 @@ static struct clk_regmap g12a_fclk_div3 = {
 		.ops = &clk_regmap_gate_ops,
 		.parent_names = (const char *[]){ "fclk_div3_div" },
 		.num_parents = 1,
+		/*
+		 * This clock is used by the resident firmware and is required
+		 * by the platform to operate correctly.
+		 * Until the following condition are met, we need this clock to
+		 * be marked as critical:
+		 * a) Mark the clock used by a firmware resource, if possible
+		 * b) CCF has a clock hand-off mechanism to make the sure the
+		 *    clock stays on until the proper driver comes along
+		 */
+		.flags = CLK_IS_CRITICAL,
 	},
 };
 
Signature · 1 line
2.21.0
maintainer Applied
#6 lore raw
In reply to Neil Armstrong
Quoted 33 lines · Neil Armstrong

The Amlogic G12B SoC is very similar with the G12A SoC, sharing most of the features and architecture.
G12B clock tree is very close, the main differences are :
- SYS_PLL is used for the second cluster (otherwise used fir the first on G12a)
- SYS_PLL1 is used for the first cluster (instead of SYS_PLL on G12a)
- A duplicate CPU tree is added for the second cluster
- G12B has additional clocks like for CSI an other components, not handled yet

Dependencies :
- Patch 1, 3 : None
- Patch 2 : Depends on Guillaume's Temperature sensor Clock patches at [1]

This patchset is a spinoff of the v2 Odroid-N2 megapatchset at [2]

Changes since v1 at [3]:
- Added the cpub_clk div2..8 and replaces the ahb/atb/axi/trace divs by muxes
- Added the CLK_GATE_SET_TO_DISABLE flag to ahb/atb/axi/trace gates
- Fixed all the G12A typos
- Added martin's reviewed by on patch 1

Changes since original patchset :
- Added missing sys1_pll div16, cpub div16 and cpub atb/axi/ahb/trace clocks
- Rewrote "This patch .." in commit messages

[1] https://lkml.kernel.org/r/[email protected]
[2] https://lkml.kernel.org/r/[email protected]
[3] https://lkml.kernel.org/r/[email protected]

Neil Armstrong (3):
dt-bindings: clk: meson: add g12b periph clock controller bindings
clk: meson: g12a: Add support for G12B CPUB clocks
clk: meson: g12a: mark fclk_div3 as critical

Quoted 5 lines
 .../bindings/clock/amlogic,gxbb-clkc.txt      |   1 +
 drivers/clk/meson/g12a.c                      | 772 ++++++++++++++++++
 drivers/clk/meson/g12a.h                      |  40 +-
 3 files changed, 812 insertions(+), 1 deletion(-)

Applied
Thx