Skip to contentSkip to conversation

Allwinner A64/H6 IR support

PATCH Superseded Clément Péron 4 participants 26 messages May 28, 2019 – Jun 14, 2019

Subsystems (4)

v3 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#0 lore raw

v3 cover Allwinner A64/H6 IR support

Hi,

A64 IR support series[1] pointed out that an A31 bindings should be introduced.

This series introduce the A31 compatible bindings, then switch it on the already existing board.

Finally introduce A64 and H6 support.

I didn't enable the IR on other H6 boards as Ondrej reported an issue on his board[2].

Regards,
Clément

[1] https://lore.kernel.org/patchwork/patch/1031390/#1221464
[2] https://lkml.org/lkml/2019/5/27/321

Changes since v2:
- Disable IR for other H6 boards
- Split DTS patch for H3/H5
- Introduce IR quirks

Changes since v1:
- Document reset lines as required since A31
- Explain the memory mapping difference in commit log
- Fix misspelling "Allwiner" to "Allwinner"

Clément Péron (10):
dt-bindings: media: sunxi-ir: add A31 compatible
media: rc: Introduce sunxi_ir_quirks
media: rc: sunxi: Add A31 compatible
ARM: dts: sunxi: Prefer A31 bindings for IR
ARM: dts: sunxi: Prefer A31 bindings for IR
dt-bindings: media: sunxi-ir: Add A64 compatible
dt-bindings: media: sunxi-ir: Add H6 compatible
arm64: dts: allwinner: h6: Add IR receiver node
arm64: dts: allwinner: h6: Enable IR on Beelink GS1
arm64: defconfig: enable IR SUNXI option

Igors Makejevs (1):
arm64: dts: allwinner: a64: Add IR node

Jernej Skrabec (1):
arm64: dts: allwinner: a64: Enable IR on Orange Pi Win

 .../devicetree/bindings/media/sunxi-ir.txt    | 11 ++-
 arch/arm/boot/dts/sun6i-a31.dtsi              |  2 +-
 arch/arm/boot/dts/sun8i-a83t.dtsi             |  2 +-
 arch/arm/boot/dts/sun9i-a80.dtsi              |  2 +-
 arch/arm/boot/dts/sunxi-h3-h5.dtsi            |  2 +-
 .../dts/allwinner/sun50i-a64-orangepi-win.dts |  4 ++
 arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 18 +++++
 .../dts/allwinner/sun50i-h6-beelink-gs1.dts   |  4 ++
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi  | 19 +++++
 arch/arm64/configs/defconfig                  |  1 +
 drivers/media/rc/sunxi-cir.c                  | 70 +++++++++++++++----
 11 files changed, 115 insertions(+), 20 deletions(-)
Signature · 7 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190528161440.27172-1-peron.clem%40gmail.com.
For more options, visit https://groups.google.com/d/optout.
#1 lore raw

PATCH v3 1/12 dt-bindings: media: sunxi-ir: add A31 compatible

Allwinner A31 has introduced a new memory mapping and a reset line.

The difference in memory mapping are :

- In the configure register there is a new sample bit and Allwinner has introduced the active threshold feature.

- In the status register a new STAT bit is present.

Note: CGPO and DRQ_EN bits are removed on A31 but present on A13 and on new SoCs like A64/H6.
This is actually not an issue as these bits are togglable and new SoCs have a dedicated bindings.

Introduce this bindings to make a difference since this generation. And declare the reset line required since A31.

---
 Documentation/devicetree/bindings/media/sunxi-ir.txt | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/media/sunxi-ir.txt +7 -2
index 278098987edb..2e59a32a7e33 100644
@@ -1,16 +1,21 @@
 Device-Tree bindings for SUNXI IR controller found in sunXi SoC family
 
 Required properties:
-- compatible	    : "allwinner,sun4i-a10-ir" or "allwinner,sun5i-a13-ir"
+- compatible	    :
+	"allwinner,sun4i-a10-ir"
+	"allwinner,sun5i-a13-ir"
+	"allwinner,sun6i-a31-ir"
 - clocks	    : list of clock specifiers, corresponding to
 		      entries in clock-names property;
 - clock-names	    : should contain "apb" and "ir" entries;
 - interrupts	    : should contain IR IRQ number;
 - reg		    : should contain IO map address for IR.
 
+Required properties since A31:
+- resets	    : phandle + reset specifier pair
+
 Optional properties:
 - linux,rc-map-name: see rc.txt file in the same directory.
-- resets : phandle + reset specifier pair
 - clock-frequency  : IR Receiver clock frequency, in Hertz. Defaults to 8 MHz
 		     if missing.
 
Signature · 7 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190528161440.27172-2-peron.clem%40gmail.com.
For more options, visit https://groups.google.com/d/optout.
maintainer Reviewed-by on v3 1/12
#2 lore raw

Re: [PATCH v3 01/12] dt-bindings: media: sunxi-ir: add A31 compatible

Quoted 15 lines · On Tue, 28 May 2019 18:14:29 +0200, =?UTF-8?q?Cl=C3=A9ment=20P=C3=A9ron?= wrote:

Allwinner A31 has introduced a new memory mapping and a reset line.

The difference in memory mapping are :

- In the configure register there is a new sample bit and Allwinner has introduced the active threshold feature.

- In the status register a new STAT bit is present.

Note: CGPO and DRQ_EN bits are removed on A31 but present on A13 and on new SoCs like A64/H6.
This is actually not an issue as these bits are togglable and new SoCs have a dedicated bindings.

Quoted 8 lines

Introduce this bindings to make a difference since this generation. And declare the reset line required since A31.

---
 Documentation/devicetree/bindings/media/sunxi-ir.txt | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)
#3 lore raw

PATCH v3 2/12 media: rc: Introduce sunxi_ir_quirks

In reply to Clément Péron

This driver is used in various Allwinner SoC with different configuration.

Introduce a quirks struct to know the fifo size and if a reset is required.

---
 drivers/media/rc/sunxi-cir.c | 61 +++++++++++++++++++++++++++---------
 1 file changed, 47 insertions(+), 14 deletions(-)
drivers/media/rc/sunxi-cir.c +47 -14
index 307e44714ea0..d02dcb6fd0a5 100644
@@ -81,6 +81,17 @@
 /* Time after which device stops sending data in ms */
 #define SUNXI_IR_TIMEOUT      120
 
+/**
+ * struct sunxi_ir_quirks - Differences between SoC variants.
+ *
+ * @has_reset: SoC needs reset deasserted.
+ * @fifo_size: size of the fifo.
+ */
+struct sunxi_ir_quirks {
+	bool		has_reset;
+	int		fifo_size;
+};
+
 struct sunxi_ir {
 	spinlock_t      ir_lock;
 	struct rc_dev   *rc;
@@ -143,6 +154,7 @@ static int sunxi_ir_probe(struct platform_device *pdev)
 
 	struct device *dev = &pdev->dev;
 	struct device_node *dn = dev->of_node;
+	const struct sunxi_ir_quirks *quirks;
 	struct resource *res;
 	struct sunxi_ir *ir;
 	u32 b_clk_freq = SUNXI_IR_BASE_CLK;
@@ -151,12 +163,15 @@ static int sunxi_ir_probe(struct platform_device *pdev)
 	if (!ir)
 		return -ENOMEM;
 
+	quirks = of_device_get_match_data(&pdev->dev);
+	if (quirks == NULL) {
+		dev_err(&pdev->dev, "Failed to determine the quirks to use\n");
+		return -ENODEV;
+	}
+
 	spin_lock_init(&ir->ir_lock);
 
-	if (of_device_is_compatible(dn, "allwinner,sun5i-a13-ir"))
-		ir->fifo_size = 64;
-	else
-		ir->fifo_size = 16;
+	ir->fifo_size = quirks->fifo_size;
 
 	/* Clock */
 	ir->apb_clk = devm_clk_get(dev, "apb");
@@ -173,13 +188,15 @@ static int sunxi_ir_probe(struct platform_device *pdev)
 	/* Base clock frequency (optional) */
 	of_property_read_u32(dn, "clock-frequency", &b_clk_freq);
 
-	/* Reset (optional) */
-	ir->rst = devm_reset_control_get_optional_exclusive(dev, NULL);
-	if (IS_ERR(ir->rst))
-		return PTR_ERR(ir->rst);
-	ret = reset_control_deassert(ir->rst);
-	if (ret)
-		return ret;
+	/* Reset */
+	if (quirks->has_reset) {
+		ir->rst = devm_reset_control_get_exclusive(dev, NULL);
+		if (IS_ERR(ir->rst))
+			return PTR_ERR(ir->rst);
+		ret = reset_control_deassert(ir->rst);
+		if (ret)
+			return ret;
+	}
 
 	ret = clk_set_rate(ir->clk, b_clk_freq);
 	if (ret) {
@@ -316,10 +333,26 @@ static int sunxi_ir_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static const struct sunxi_ir_quirks sun4i_a10_ir_quirks = {
+	.has_reset = false,
+	.fifo_size = 16,
+};
+
+static const struct sunxi_ir_quirks sun5i_a13_ir_quirks = {
+	.has_reset = false,
+	.fifo_size = 64,
+};
+
 static const struct of_device_id sunxi_ir_match[] = {
-	{ .compatible = "allwinner,sun4i-a10-ir", },
-	{ .compatible = "allwinner,sun5i-a13-ir", },
-	{},
+	{
+		.compatible = "allwinner,sun4i-a10-ir",
+		.data = &sun4i_a10_ir_quirks,
+	},
+	{
+		.compatible = "allwinner,sun5i-a13-ir",
+		.data = &sun5i_a13_ir_quirks,
+	},
+	{}
 };
 MODULE_DEVICE_TABLE(of, sunxi_ir_match);
 
Signature · 7 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190528161440.27172-3-peron.clem%40gmail.com.
For more options, visit https://groups.google.com/d/optout.
#4 lore raw

PATCH v3 3/12 media: rc: sunxi: Add A31 compatible

In reply to Clément Péron

Allwiner A31 has a different memory mapping so add the compatible we will need it later.

---
 drivers/media/rc/sunxi-cir.c | 9 +++++++++
 1 file changed, 9 insertions(+)
drivers/media/rc/sunxi-cir.c +9 -0
index d02dcb6fd0a5..0504ebfc831f 100644
@@ -343,6 +343,11 @@ static const struct sunxi_ir_quirks sun5i_a13_ir_quirks = {
 	.fifo_size = 64,
 };
 
+static const struct sunxi_ir_quirks sun6i_a31_ir_quirks = {
+	.has_reset = true,
+	.fifo_size = 64,
+};
+
 static const struct of_device_id sunxi_ir_match[] = {
 	{
 		.compatible = "allwinner,sun4i-a10-ir",
@@ -352,6 +357,10 @@ static const struct of_device_id sunxi_ir_match[] = {
 		.compatible = "allwinner,sun5i-a13-ir",
 		.data = &sun5i_a13_ir_quirks,
 	},
+	{
+		.compatible = "allwinner,sun6i-a31-ir",
+		.data = &sun6i_a31_ir_quirks,
+	},
 	{}
 };
 MODULE_DEVICE_TABLE(of, sunxi_ir_match);
Signature · 7 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190528161440.27172-4-peron.clem%40gmail.com.
For more options, visit https://groups.google.com/d/optout.
#5 lore raw

Re: [PATCH v3 03/12] media: rc: sunxi: Add A31 compatible

Quoted 13 lines · Clément Péron

Allwiner A31 has a different memory mapping so add the compatible we will need it later.

---
 drivers/media/rc/sunxi-cir.c | 9 +++++++++
 1 file changed, 9 insertions(+)
drivers/media/rc/sunxi-cir.c +0 -0
index d02dcb6fd0a5..0504ebfc831f 100644

drivers/media/rc/sunxi-cir.c static const struct sunxi_ir_quirks sun5i_a13_ir_quirks = { · line 350

Quoted 8 lines
drivers/media/rc/sunxi-cir.c +5 -0
@@ -343,6 +343,11 @@ static const struct sunxi_ir_quirks sun5i_a13_ir_quirks = {
 	.fifo_size = 64,
 };
 
+static const struct sunxi_ir_quirks sun6i_a31_ir_quirks = {
+	.has_reset = true,
+	.fifo_size = 64,
+};
+

BTW, H6 BSP uses FIFO size 40:

https://github.com/orangepi-xunlong/OrangePiH6_Linux4_9/blob/master/drivers/media/rc/sunxi-ir-dev.c#L290

Have you tried filling the fifo with over 40 words on H6, to see if it works?

I know it's docummented as having 64 words in the manual, so maybe Allwiner just didn't care enough to make the driver configurable, and the H6 FIFO really has that depth.

regards,

	o.
Quoted 22 lines
drivers/media/rc/sunxi-cir.c +4 -0
 static const struct of_device_id sunxi_ir_match[] = {
 	{
 		.compatible = "allwinner,sun4i-a10-ir",
@@ -352,6 +357,10 @@ static const struct of_device_id sunxi_ir_match[] = {
 		.compatible = "allwinner,sun5i-a13-ir",
 		.data = &sun5i_a13_ir_quirks,
 	},
+	{
+		.compatible = "allwinner,sun6i-a31-ir",
+		.data = &sun6i_a31_ir_quirks,
+	},
 	{}
 };
 MODULE_DEVICE_TABLE(of, sunxi_ir_match);
Signature · 7 lines
2.20.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#6 lore raw

Re: [PATCH v3 03/12] media: rc: sunxi: Add A31 compatible

Hi,

Quoted 26 lines · Ondřej Jirman
Quoted 13 lines · Clément Péron

Allwiner A31 has a different memory mapping so add the compatible we will need it later.

---
 drivers/media/rc/sunxi-cir.c | 9 +++++++++
 1 file changed, 9 insertions(+)
drivers/media/rc/sunxi-cir.c +0 -0
index d02dcb6fd0a5..0504ebfc831f 100644

drivers/media/rc/sunxi-cir.c static const struct sunxi_ir_quirks sun5i_a13_ir_quirks = { · line 350

Quoted 8 lines
drivers/media/rc/sunxi-cir.c +5 -0
@@ -343,6 +343,11 @@ static const struct sunxi_ir_quirks sun5i_a13_ir_quirks = {
      .fifo_size = 64,
 };
 
+static const struct sunxi_ir_quirks sun6i_a31_ir_quirks = {
+     .has_reset = true,
+     .fifo_size = 64,
+};
+

BTW, H6 BSP uses FIFO size 40:

Quoted 3 lines

https://github.com/orangepi-xunlong/OrangePiH6_Linux4_9/blob/master/drivers/media/rc/sunxi-ir-dev.c#L290

Have you tried filling the fifo with over 40 words on H6, to see if it works?

No I didn't try this, but I trust more the user manual than the driver. And I don't see why they would have reduce the fifo size in the new generation. Anyway, I will be able to test that at the end of the week.

Regards,
Clément

Quoted 29 lines

I know it's docummented as having 64 words in the manual, so maybe Allwiner just didn't care enough to make the driver configurable, and the H6 FIFO really has that depth.

regards,

        o.
Quoted 22 lines
drivers/media/rc/sunxi-cir.c +4 -1
 static const struct of_device_id sunxi_ir_match[] = {
      {
              .compatible = "allwinner,sun4i-a10-ir",
@@ -352,6 +357,10 @@ static const struct of_device_id sunxi_ir_match[] = {
              .compatible = "allwinner,sun5i-a13-ir",
              .data = &sun5i_a13_ir_quirks,
      },
+     {
+             .compatible = "allwinner,sun6i-a31-ir",
+             .data = &sun6i_a31_ir_quirks,
+     },
      {}
 };
 MODULE_DEVICE_TABLE(of, sunxi_ir_match);
--

2.20.1

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#7 lore raw

PATCH v3 4/12 ARM: dts: sunxi: Prefer A31 bindings for IR

In reply to Clément Péron

Since A31, memory mapping of the IR driver has changed.

Prefer the A31 bindings instead of A13.

---
 arch/arm/boot/dts/sun6i-a31.dtsi  | 2 +-
 arch/arm/boot/dts/sun8i-a83t.dtsi | 2 +-
 arch/arm/boot/dts/sun9i-a80.dtsi  | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)
arch/arm/boot/dts/sun6i-a31.dtsi +1 -1
index c04efad81bbc..110622b30796 100644
@@ -1351,7 +1351,7 @@
 		};
 
 		ir: ir@1f02000 {
-			compatible = "allwinner,sun5i-a13-ir";
+			compatible = "allwinner,sun6i-a31-ir";
 			clocks = <&apb0_gates 1>, <&ir_clk>;
 			clock-names = "apb", "ir";
 			resets = <&apb0_rst 1>;
arch/arm/boot/dts/sun8i-a83t.dtsi +1 -1
index 392b0cabbf0d..8d603f3309f2 100644
@@ -1067,7 +1067,7 @@
 
 		r_cir: ir@1f02000 {
 			compatible = "allwinner,sun8i-a83t-ir",
-				"allwinner,sun5i-a13-ir";
+				"allwinner,sun6i-a31-ir";
 			clocks = <&r_ccu CLK_APB0_IR>, <&r_ccu CLK_IR>;
 			clock-names = "apb", "ir";
 			resets = <&r_ccu RST_APB0_IR>;
arch/arm/boot/dts/sun9i-a80.dtsi +1 -1
index 0c1eec9000e3..310cd972ee5b 100644
@@ -1167,7 +1167,7 @@
 		};
 
 		r_ir: ir@8002000 {
-			compatible = "allwinner,sun5i-a13-ir";
+			compatible = "allwinner,sun6i-a31-ir";
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&r_ir_pins>;
Signature · 7 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190528161440.27172-5-peron.clem%40gmail.com.
For more options, visit https://groups.google.com/d/optout.
#8 lore raw

PATCH v3 5/12 ARM: dts: sunxi: Prefer A31 bindings for IR

In reply to Clément Péron

Since A31, memory mapping of the IR driver has changed.

Prefer the A31 bindings instead of A13.

---
 arch/arm/boot/dts/sunxi-h3-h5.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/sunxi-h3-h5.dtsi +1 -1
index 84977d4eb97a..f0f5ba349c1b 100644
@@ -822,7 +822,7 @@
 		};
 
 		ir: ir@1f02000 {
-			compatible = "allwinner,sun5i-a13-ir";
+			compatible = "allwinner,sun6i-a31-ir";
 			clocks = <&r_ccu CLK_APB0_IR>, <&r_ccu CLK_IR>;
 			clock-names = "apb", "ir";
 			resets = <&r_ccu RST_APB0_IR>;
Signature · 7 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190528161440.27172-6-peron.clem%40gmail.com.
For more options, visit https://groups.google.com/d/optout.
#9 lore raw

PATCH v3 6/12 dt-bindings: media: sunxi-ir: Add A64 compatible

In reply to Clément Péron

There are some minor differences between A31 and A64 driver.

But A31 IR driver is compatible with A64.

---
 Documentation/devicetree/bindings/media/sunxi-ir.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/media/sunxi-ir.txt +1 -0
index 2e59a32a7e33..1dd287a4ab3a 100644
@@ -5,6 +5,7 @@ Required properties:
 	"allwinner,sun4i-a10-ir"
 	"allwinner,sun5i-a13-ir"
 	"allwinner,sun6i-a31-ir"
+	"allwinner,sun50i-a64-ir", "allwinner,sun6i-a31-ir"
 - clocks	    : list of clock specifiers, corresponding to
 		      entries in clock-names property;
 - clock-names	    : should contain "apb" and "ir" entries;
Signature · 7 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190528161440.27172-7-peron.clem%40gmail.com.
For more options, visit https://groups.google.com/d/optout.
#10 lore raw

PATCH v3 7/12 arm64: dts: allwinner: a64: Add IR node

In reply to Clément Péron

From: Igors Makejevs <git_bb-v/FNU3S1YP/[email protected]>

IR peripheral is completely compatible with A31 one.

---
 arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi +18 -0
index 8c5b521e6389..b22b0aa89515 100644
@@ -1072,6 +1072,19 @@
 			#size-cells = <0>;
 		};
 
+		r_ir: ir@1f02000 {
+			compatible = "allwinner,sun50i-a64-ir",
+				     "allwinner,sun6i-a31-ir";
+			reg = <0x01f02000 0x400>;
+			clocks = <&r_ccu CLK_APB0_IR>, <&r_ccu CLK_IR>;
+			clock-names = "apb", "ir";
+			resets = <&r_ccu RST_APB0_IR>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_ir_rx_pin>;
+			status = "disabled";
+		};
+
 		r_pwm: pwm@1f03800 {
 			compatible = "allwinner,sun50i-a64-pwm",
 				     "allwinner,sun5i-a13-pwm";
@@ -1099,6 +1112,11 @@
 				function = "s_i2c";
 			};
 
+			r_ir_rx_pin: r-ir-rx-pin {
+				pins = "PL11";
+				function = "s_cir_rx";
+			};
+
 			r_pwm_pin: r-pwm-pin {
 				pins = "PL10";
 				function = "s_pwm";
Signature · 7 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190528161440.27172-8-peron.clem%40gmail.com.
For more options, visit https://groups.google.com/d/optout.
#11 lore raw

PATCH v3 8/12 arm64: dts: allwinner: a64: Enable IR on Orange Pi Win

In reply to Clément Péron

From: Jernej Skrabec <[email protected]>

OrangePi Win board contains IR receiver. Enable it.

---
 arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts +4 -0
index 510f661229dc..e05191b71adf 100644
@@ -180,6 +180,10 @@
 	status = "okay";
 };
 
+&r_ir {
+	status = "okay";
+};
+
 &r_rsb {
 	status = "okay";
 
Signature · 7 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190528161440.27172-9-peron.clem%40gmail.com.
For more options, visit https://groups.google.com/d/optout.
#12 lore raw

PATCH v3 9/12 dt-bindings: media: sunxi-ir: Add H6 compatible

In reply to Clément Péron

There are some minor differences between A31 or A64 with H6 IR peripheral.

But A31 IR driver is compatible with H6.

---
 Documentation/devicetree/bindings/media/sunxi-ir.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/media/sunxi-ir.txt +1 -0
index 1dd287a4ab3a..81eaf95fb764 100644
@@ -6,6 +6,7 @@ Required properties:
 	"allwinner,sun5i-a13-ir"
 	"allwinner,sun6i-a31-ir"
 	"allwinner,sun50i-a64-ir", "allwinner,sun6i-a31-ir"
+	"allwinner,sun50i-h6-ir", "allwinner,sun6i-a31-ir"
 - clocks	    : list of clock specifiers, corresponding to
 		      entries in clock-names property;
 - clock-names	    : should contain "apb" and "ir" entries;
Signature · 7 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190528161440.27172-10-peron.clem%40gmail.com.
For more options, visit https://groups.google.com/d/optout.
#13 lore raw

PATCH v3 10/12 arm64: dts: allwinner: h6: Add IR receiver node

In reply to Clément Péron

Allwinner H6 IR is similar to A31 and can use same driver.

Add support for it.

---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +19 -0
index 16c5c3d0fd81..649cbdfe452e 100644
@@ -647,6 +647,25 @@
 				pins = "PL0", "PL1";
 				function = "s_i2c";
 			};
+
+			r_ir_rx_pin: r-ir-rx-pin {
+				pins = "PL9";
+				function = "s_cir_rx";
+			};
+		};
+
+		r_ir: ir@7040000 {
+				compatible = "allwinner,sun50i-h6-ir",
+					     "allwinner,sun6i-a31-ir";
+				reg = <0x07040000 0x400>;
+				interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&r_ccu CLK_R_APB1_IR>,
+					 <&r_ccu CLK_IR>;
+				clock-names = "apb", "ir";
+				resets = <&r_ccu RST_R_APB1_IR>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&r_ir_rx_pin>;
+				status = "disabled";
 		};
 
 		r_i2c: i2c@7081400 {
Signature · 7 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190528161440.27172-11-peron.clem%40gmail.com.
For more options, visit https://groups.google.com/d/optout.
#14 lore raw

Re: [PATCH v3 10/12] arm64: dts: allwinner: h6: Add IR receiver node

Hello Clément,

Quoted 27 lines · Clément Péron

Allwinner H6 IR is similar to A31 and can use same driver.

Add support for it.

---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +10 -0
index 16c5c3d0fd81..649cbdfe452e 100644
@@ -647,6 +647,25 @@
 				pins = "PL0", "PL1";
 				function = "s_i2c";
 			};
+
+			r_ir_rx_pin: r-ir-rx-pin {
+				pins = "PL9";
+				function = "s_cir_rx";
+			};
+		};
+
+		r_ir: ir@7040000 {
+				compatible = "allwinner,sun50i-h6-ir",
+					     "allwinner,sun6i-a31-ir";

arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi line 669

Quoted 10 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +9 -0
+				reg = <0x07040000 0x400>;
+				interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&r_ccu CLK_R_APB1_IR>,
+					 <&r_ccu CLK_IR>;
+				clock-names = "apb", "ir";
+				resets = <&r_ccu RST_R_APB1_IR>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&r_ir_rx_pin>;
+				status = "disabled";
 		};

Please make a comment here, that this is known broken on some boards and may result IRQ flood if enabled. Otherwise noone will know.

thanks,

	o.
Quoted 9 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +0 -0
 		r_i2c: i2c@7081400 {
Signature · 7 lines
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Signature · 4 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190530145550.amalnxmx7kpokykv%40core.my.home.
For more options, visit https://groups.google.com/d/optout.
#15 lore raw

Re: [PATCH v3 10/12] arm64: dts: allwinner: h6: Add IR receiver node

Hi Ondrej,

Quoted 36 lines · Ondřej Jirman

Hello Clément,

Quoted 32 lines · Clément Péron

Allwinner H6 IR is similar to A31 and can use same driver.

Add support for it.

---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +15 -0
index 16c5c3d0fd81..649cbdfe452e 100644
@@ -647,6 +647,25 @@
                              pins = "PL0", "PL1";
                              function = "s_i2c";
                      };
+
+                     r_ir_rx_pin: r-ir-rx-pin {
+                             pins = "PL9";
+                             function = "s_cir_rx";
+                     };
+             };
+
+             r_ir: ir@7040000 {
+                             compatible = "allwinner,sun50i-h6-ir",
+                                          "allwinner,sun6i-a31-ir";
+                             reg = <0x07040000 0x400>;
+                             interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+                             clocks = <&r_ccu CLK_R_APB1_IR>,
+                                      <&r_ccu CLK_IR>;
+                             clock-names = "apb", "ir";
Quoted 8 lines

arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi line 669

Quoted 5 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +4 -0
+                             resets = <&r_ccu RST_R_APB1_IR>;
+                             pinctrl-names = "default";
+                             pinctrl-0 = <&r_ir_rx_pin>;
+                             status = "disabled";
              };

Please make a comment here, that this is known broken on some boards and may result IRQ flood if enabled. Otherwise noone will know.

I'm planning to send a v4 next week with the IRQ_NONE return as Maxime suggested it.
https://github.com/clementperon/linux/tree/h6_ir_v4

But maybe we could also use the bit 5 of the IRQ status.

Regards, Clement

Quoted 13 lines

thanks,

        o.
Quoted 9 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +0 -1
              r_i2c: i2c@7081400 {
--

2.20.1

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#16 lore raw

Re: [linux-sunxi] Re: [PATCH v3 10/12] arm64: dts: allwinner: h6: Add IR receiver node

Hello Clément,

Quoted 48 lines · Clément Péron

Hi Ondrej,

Quoted 36 lines · Ondřej Jirman

Hello Clément,

Quoted 32 lines · Clément Péron

Allwinner H6 IR is similar to A31 and can use same driver.

Add support for it.

---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +15 -0
index 16c5c3d0fd81..649cbdfe452e 100644
@@ -647,6 +647,25 @@
                              pins = "PL0", "PL1";
                              function = "s_i2c";
                      };
+
+                     r_ir_rx_pin: r-ir-rx-pin {
+                             pins = "PL9";
+                             function = "s_cir_rx";
+                     };
+             };
+
+             r_ir: ir@7040000 {
+                             compatible = "allwinner,sun50i-h6-ir",
+                                          "allwinner,sun6i-a31-ir";
+                             reg = <0x07040000 0x400>;
+                             interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+                             clocks = <&r_ccu CLK_R_APB1_IR>,
+                                      <&r_ccu CLK_IR>;
+                             clock-names = "apb", "ir";
Quoted 8 lines

arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi line 669

Quoted 5 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +4 -0
+                             resets = <&r_ccu RST_R_APB1_IR>;
+                             pinctrl-names = "default";
+                             pinctrl-0 = <&r_ir_rx_pin>;
+                             status = "disabled";
              };

Please make a comment here, that this is known broken on some boards and may result IRQ flood if enabled. Otherwise noone will know.

Quoted 5 lines

I'm planning to send a v4 next week with the IRQ_NONE return as Maxime suggested it.
https://github.com/clementperon/linux/tree/h6_ir_v4

But maybe we could also use the bit 5 of the IRQ status.

Thanks, that's nice, but that will not make the HW work. That will just disable it. The comment is still necessary.

thank you,

	o.
Quoted 21 lines

Regards, Clement

Quoted 13 lines

thanks,

        o.
Quoted 9 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +0 -1
              r_i2c: i2c@7081400 {
--

2.20.1

_______________________________________________
linux-arm-kernel mailing list linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Signature · 4 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/CAJiuCce7nHSktVsDKcR8GLRpD3WrN5yP3Nb_Hbu_Q9NjUQbSMw%40mail.gmail.com.
For more options, visit https://groups.google.com/d/optout.
Signature · 4 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190531124630.q2guo54kjfzr7rkn%40core.my.home.
For more options, visit https://groups.google.com/d/optout.
#17 lore raw

Re: [linux-sunxi] Re: [PATCH v3 10/12] arm64: dts: allwinner: h6: Add IR receiver node

Hi Ondrej,

Quoted 52 lines · Ondřej Jirman

Hello Clément,

Quoted 48 lines · Clément Péron

Hi Ondrej,

Quoted 44 lines · Ondřej Jirman

Hello Clément,

Quoted 27 lines · Clément Péron

Allwinner H6 IR is similar to A31 and can use same driver.

Add support for it.

---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +10 -0
index 16c5c3d0fd81..649cbdfe452e 100644
@@ -647,6 +647,25 @@
                              pins = "PL0", "PL1";
                              function = "s_i2c";
                      };
+
+                     r_ir_rx_pin: r-ir-rx-pin {
+                             pins = "PL9";
+                             function = "s_cir_rx";
+                     };
+             };
+
+             r_ir: ir@7040000 {
+                             compatible = "allwinner,sun50i-h6-ir",
+                                          "allwinner,sun6i-a31-ir";

arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi line 669

Quoted 10 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +9 -0
+                             reg = <0x07040000 0x400>;
+                             interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+                             clocks = <&r_ccu CLK_R_APB1_IR>,
+                                      <&r_ccu CLK_IR>;
+                             clock-names = "apb", "ir";
+                             resets = <&r_ccu RST_R_APB1_IR>;
+                             pinctrl-names = "default";
+                             pinctrl-0 = <&r_ir_rx_pin>;
+                             status = "disabled";
              };

Please make a comment here, that this is known broken on some boards and may result IRQ flood if enabled. Otherwise noone will know.

Quoted 8 lines
Quoted 5 lines

I'm planning to send a v4 next week with the IRQ_NONE return as Maxime suggested it.
https://github.com/clementperon/linux/tree/h6_ir_v4

But maybe we could also use the bit 5 of the IRQ status.

Thanks, that's nice, but that will not make the HW work. That will just disable it. The comment is still necessary.

I have pushed a new version on my github.
https://github.com/clementperon/linux/commits/h6_ir_v4

I will submit it, if you are ok with it.

Thanks,
Clément

Quoted 25 lines

thank you,

        o.
Quoted 21 lines

Regards, Clement

Quoted 13 lines

thanks,

        o.
Quoted 9 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +0 -1
              r_i2c: i2c@7081400 {
--

2.20.1

_______________________________________________
linux-arm-kernel mailing list linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected] To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/CAJiuCce7nHSktVsDKcR8GLRpD3WrN5yP3Nb_Hbu_Q9NjUQbSMw%40mail.gmail.com.
For more options, visit https://groups.google.com/d/optout.

Signature · 4 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/CAJiuCcdMftAjCwk2_naE9VBGGqS%3DOY9xcqv6%2B5pDX2Z8O%3DL28w%40mail.gmail.com.
For more options, visit https://groups.google.com/d/optout.
#18 lore raw

Re: [linux-sunxi] Re: [PATCH v3 10/12] arm64: dts: allwinner: h6: Add IR receiver node

Hi Clément,

Quoted 59 lines · Clément Péron

Hi Ondrej,

Quoted 56 lines · Ondřej Jirman

Hello Clément,

Quoted 52 lines · Clément Péron

Hi Ondrej,

Quoted 36 lines · Ondřej Jirman

Hello Clément,

Quoted 32 lines · Clément Péron

Allwinner H6 IR is similar to A31 and can use same driver.

Add support for it.

---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +15 -0
index 16c5c3d0fd81..649cbdfe452e 100644
@@ -647,6 +647,25 @@
                              pins = "PL0", "PL1";
                              function = "s_i2c";
                      };
+
+                     r_ir_rx_pin: r-ir-rx-pin {
+                             pins = "PL9";
+                             function = "s_cir_rx";
+                     };
+             };
+
+             r_ir: ir@7040000 {
+                             compatible = "allwinner,sun50i-h6-ir",
+                                          "allwinner,sun6i-a31-ir";
+                             reg = <0x07040000 0x400>;
+                             interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+                             clocks = <&r_ccu CLK_R_APB1_IR>,
+                                      <&r_ccu CLK_IR>;
+                             clock-names = "apb", "ir";
Quoted 8 lines

arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi line 669

Quoted 5 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +4 -0
+                             resets = <&r_ccu RST_R_APB1_IR>;
+                             pinctrl-names = "default";
+                             pinctrl-0 = <&r_ir_rx_pin>;
+                             status = "disabled";
              };

Please make a comment here, that this is known broken on some boards and may result IRQ flood if enabled. Otherwise noone will know.

I'm planning to send a v4 next week with the IRQ_NONE return as Maxime suggested it.
https://github.com/clementperon/linux/tree/h6_ir_v4

Quoted 8 lines
Quoted 4 lines
Quoted 1 line

But maybe we could also use the bit 5 of the IRQ status.

Thanks, that's nice, but that will not make the HW work. That will just disable it. The comment is still necessary.

I have pushed a new version on my github.
https://github.com/clementperon/linux/commits/h6_ir_v4

I will submit it, if you are ok with it.

the changes make it worse. Console is flooded with "Temporarily disable IRQ" and other symptoms are the same as I described before. Interrupts are not disabled in a any reasonable time. (I've waited for more > 5mins already.)

You probably need to disable interrupts right away, not wait for 100k failures.

thank you and regards,

	o.
Quoted 33 lines

Thanks,
Clément

Quoted 25 lines

thank you,

        o.
Quoted 21 lines

Regards, Clement

Quoted 13 lines

thanks,

        o.
Quoted 9 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +0 -1
              r_i2c: i2c@7081400 {
--

2.20.1

_______________________________________________
linux-arm-kernel mailing list linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected] To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/CAJiuCce7nHSktVsDKcR8GLRpD3WrN5yP3Nb_Hbu_Q9NjUQbSMw%40mail.gmail.com.
For more options, visit https://groups.google.com/d/optout.

_______________________________________________
linux-arm-kernel mailing list linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Signature · 4 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190604123355.m47ufmhtzuzfvmp7%40core.my.home.
For more options, visit https://groups.google.com/d/optout.
#19 lore raw

Re: [linux-sunxi] Re: [PATCH v3 10/12] arm64: dts: allwinner: h6: Add IR receiver node

Hi Clément,

Quoted 69 lines · verejna

Hi Clément,

Quoted 66 lines · Clément Péron

Hi Ondrej,

Quoted 52 lines · Ondřej Jirman

Hello Clément,

Quoted 48 lines · Clément Péron

Hi Ondrej,

Quoted 44 lines · Ondřej Jirman

Hello Clément,

Quoted 27 lines · Clément Péron

Allwinner H6 IR is similar to A31 and can use same driver.

Add support for it.

---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +10 -0
index 16c5c3d0fd81..649cbdfe452e 100644
@@ -647,6 +647,25 @@
                              pins = "PL0", "PL1";
                              function = "s_i2c";
                      };
+
+                     r_ir_rx_pin: r-ir-rx-pin {
+                             pins = "PL9";
+                             function = "s_cir_rx";
+                     };
+             };
+
+             r_ir: ir@7040000 {
+                             compatible = "allwinner,sun50i-h6-ir",
+                                          "allwinner,sun6i-a31-ir";

arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi line 669

Quoted 10 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +9 -0
+                             reg = <0x07040000 0x400>;
+                             interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+                             clocks = <&r_ccu CLK_R_APB1_IR>,
+                                      <&r_ccu CLK_IR>;
+                             clock-names = "apb", "ir";
+                             resets = <&r_ccu RST_R_APB1_IR>;
+                             pinctrl-names = "default";
+                             pinctrl-0 = <&r_ir_rx_pin>;
+                             status = "disabled";
              };

Please make a comment here, that this is known broken on some boards and may result IRQ flood if enabled. Otherwise noone will know.

Quoted 8 lines
Quoted 5 lines

I'm planning to send a v4 next week with the IRQ_NONE return as Maxime suggested it.
https://github.com/clementperon/linux/tree/h6_ir_v4

But maybe we could also use the bit 5 of the IRQ status.

Thanks, that's nice, but that will not make the HW work. That will just disable it. The comment is still necessary.

I have pushed a new version on my github.
https://github.com/clementperon/linux/commits/h6_ir_v4

Quoted 7 lines
Quoted 1 line

I will submit it, if you are ok with it.

the changes make it worse. Console is flooded with "Temporarily disable IRQ" and other symptoms are the same as I described before. Interrupts are not disabled in a any reasonable time. (I've waited for more > 5mins already.)

You probably need to disable interrupts right away, not wait for 100k failures.

Hmm, this is what the registers look like post-probe:

R_CIR:
0x07040000 : 00000030
0x07040004 : 00000030
0x07040008 : 00000030
0x0704000c : 00000030
0x07040010 : 00000030
0x07040014 : 00000030
0x07040018 : 00000030
0x0704001c : 00000030
0x07040020 : 00000030
0x07040024 : 00000030
0x07040028 : 00000030
0x0704002c : 00000030
0x07040030 : 00000030
0x07040034 : 00000030
0x07040038 : 00000030
0x0704003c : 00000030
0x07040040 : 00000030
0x07040044 : 00000030
0x07040048 : 00000030
0x0704004c : 00000030
0x07040050 : 00000030
0x07040054 : 00000030
0x07040058 : 00000030
0x0704005c : 00000030
0x07040060 : 00000030
0x07040064 : 00000030
0x07040068 : 00000030
0x0704006c : 00000030
0x07040070 : 00000030
0x07040074 : 00000030
0x07040078 : 00000030
0x0704007c : 00000030
0x07040080 : 00000030
0x07040084 : 00000030
0x07040088 : 00000030
0x0704008c : 00000030
0x07040090 : 00000030
0x07040094 : 00000030
0x07040098 : 00000030
0x0704009c : 00000030
0x070400a0 : 00000030
0x070400a4 : 00000030
0x070400a8 : 00000030
0x070400ac : 00000030
0x070400b0 : 00000030
0x070400b4 : 00000030
0x070400b8 : 00000030
0x070400bc : 00000030
0x070400c0 : 00000030
0x070400c4 : 00000030
0x070400c8 : 00000030
0x070400cc : 00000030
0x070400d0 : 00000030
0x070400d4 : 00000030
0x070400d8 : 00000030
0x070400dc : 00000030
0x070400e0 : 00000030
0x070400e4 : 00000030
0x070400e8 : 00000030
0x070400ec : 00000030
0x070400f0 : 00000030
0x070400f4 : 00000030
0x070400f8 : 00000030
0x070400fc : 00000030

Clearly not right. It's just the R_CIR module, other modules have normal values.

I've checked:
0x070101c0 : 81000002
(IR clock config register)
0x070101cc : 00010000
(IR reset/bus clk gate reg)

static const char * const r_mod0_default_parents[] = { "osc32k", "osc24M" }; static SUNXI_CCU_MP_WITH_MUX_GATE(ir_clk, "ir",

                                  r_mod0_default_parents, 0x1c0,
                                  0, 5,         /* M */
                                  8, 2,         /* P */
                                  24, 1,        /* mux */
                                  BIT(31),      /* gate */
                                  0);

static SUNXI_CCU_GATE(r_apb1_ir_clk, "r-apb1-ir", "r-apb1",

                      0x1cc, BIT(0), 0);

        [RST_R_APB1_IR]         =  { 0x1cc, BIT(16) },

So parent clock seems to be OK. But gate clock is not enabled, so the bus is not working.

And look at this!!:

static SUNXI_CCU_GATE(r_apb1_ir_clk, "r-apb1-ir", "r-apb1",

                      0x1cc, BIT(0), 0);
static SUNXI_CCU_GATE(r_apb1_w1_clk,    "r-apb1-w1",    "r-apb1",
                      0x1cc, BIT(0), 0);

So, it's wrong w1 gate config!

You can drop your changes, because I've probbably found the root cause.

regards,

	o.
Quoted 41 lines

thank you and regards,

	o.
Quoted 29 lines

Thanks,
Clément

Quoted 25 lines

thank you,

        o.
Quoted 21 lines

Regards, Clement

Quoted 13 lines

thanks,

        o.
Quoted 9 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +0 -1
              r_i2c: i2c@7081400 {
--

2.20.1

_______________________________________________
linux-arm-kernel mailing list linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected] To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/CAJiuCce7nHSktVsDKcR8GLRpD3WrN5yP3Nb_Hbu_Q9NjUQbSMw%40mail.gmail.com.
For more options, visit https://groups.google.com/d/optout.

Quoted 4 lines

_______________________________________________
linux-arm-kernel mailing list linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

_______________________________________________
linux-arm-kernel mailing list linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Signature · 4 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190604144757.xvggmj6asyf44vuc%40core.my.home.
For more options, visit https://groups.google.com/d/optout.
#20 lore raw

Re: [linux-sunxi] Re: [PATCH v3 10/12] arm64: dts: allwinner: h6: Add IR receiver node

Hi Ondrej,

Quoted 176 lines · Ondřej Jirman

Hi Clément,

Quoted 69 lines · verejna

Hi Clément,

Quoted 66 lines · Clément Péron

Hi Ondrej,

Quoted 52 lines · Ondřej Jirman

Hello Clément,

Quoted 48 lines · Clément Péron

Hi Ondrej,

Quoted 44 lines · Ondřej Jirman

Hello Clément,

Quoted 27 lines · Clément Péron

Allwinner H6 IR is similar to A31 and can use same driver.

Add support for it.

---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +10 -0
index 16c5c3d0fd81..649cbdfe452e 100644
@@ -647,6 +647,25 @@
                              pins = "PL0", "PL1";
                              function = "s_i2c";
                      };
+
+                     r_ir_rx_pin: r-ir-rx-pin {
+                             pins = "PL9";
+                             function = "s_cir_rx";
+                     };
+             };
+
+             r_ir: ir@7040000 {
+                             compatible = "allwinner,sun50i-h6-ir",
+                                          "allwinner,sun6i-a31-ir";

arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi line 669

Quoted 10 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +9 -0
+                             reg = <0x07040000 0x400>;
+                             interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+                             clocks = <&r_ccu CLK_R_APB1_IR>,
+                                      <&r_ccu CLK_IR>;
+                             clock-names = "apb", "ir";
+                             resets = <&r_ccu RST_R_APB1_IR>;
+                             pinctrl-names = "default";
+                             pinctrl-0 = <&r_ir_rx_pin>;
+                             status = "disabled";
              };

Please make a comment here, that this is known broken on some boards and may result IRQ flood if enabled. Otherwise noone will know.

Quoted 8 lines
Quoted 5 lines

I'm planning to send a v4 next week with the IRQ_NONE return as Maxime suggested it.
https://github.com/clementperon/linux/tree/h6_ir_v4

But maybe we could also use the bit 5 of the IRQ status.

Thanks, that's nice, but that will not make the HW work. That will just disable it. The comment is still necessary.

I have pushed a new version on my github.
https://github.com/clementperon/linux/commits/h6_ir_v4

Quoted 7 lines
Quoted 1 line

I will submit it, if you are ok with it.

the changes make it worse. Console is flooded with "Temporarily disable IRQ" and other symptoms are the same as I described before. Interrupts are not disabled in a any reasonable time. (I've waited for more > 5mins already.)

You probably need to disable interrupts right away, not wait for 100k failures.

Hmm, this is what the registers look like post-probe:

R_CIR:
0x07040000 : 00000030
0x07040004 : 00000030
0x07040008 : 00000030
0x0704000c : 00000030
0x07040010 : 00000030
0x07040014 : 00000030
0x07040018 : 00000030
0x0704001c : 00000030
0x07040020 : 00000030
0x07040024 : 00000030
0x07040028 : 00000030
0x0704002c : 00000030
0x07040030 : 00000030
0x07040034 : 00000030
0x07040038 : 00000030
0x0704003c : 00000030
0x07040040 : 00000030
0x07040044 : 00000030
0x07040048 : 00000030
0x0704004c : 00000030
0x07040050 : 00000030
0x07040054 : 00000030
0x07040058 : 00000030
0x0704005c : 00000030
0x07040060 : 00000030
0x07040064 : 00000030
0x07040068 : 00000030
0x0704006c : 00000030
0x07040070 : 00000030
0x07040074 : 00000030
0x07040078 : 00000030
0x0704007c : 00000030
0x07040080 : 00000030
0x07040084 : 00000030
0x07040088 : 00000030
0x0704008c : 00000030
0x07040090 : 00000030
0x07040094 : 00000030
0x07040098 : 00000030
0x0704009c : 00000030
0x070400a0 : 00000030
0x070400a4 : 00000030
0x070400a8 : 00000030
0x070400ac : 00000030
0x070400b0 : 00000030
0x070400b4 : 00000030
0x070400b8 : 00000030
0x070400bc : 00000030
0x070400c0 : 00000030
0x070400c4 : 00000030
0x070400c8 : 00000030
0x070400cc : 00000030
0x070400d0 : 00000030
0x070400d4 : 00000030
0x070400d8 : 00000030
0x070400dc : 00000030
0x070400e0 : 00000030
0x070400e4 : 00000030
0x070400e8 : 00000030
0x070400ec : 00000030
0x070400f0 : 00000030
0x070400f4 : 00000030
0x070400f8 : 00000030
0x070400fc : 00000030

Clearly not right. It's just the R_CIR module, other modules have normal values.

I've checked:
0x070101c0 : 81000002
(IR clock config register)
0x070101cc : 00010000
(IR reset/bus clk gate reg)

static const char * const r_mod0_default_parents[] = { "osc32k", "osc24M" }; static SUNXI_CCU_MP_WITH_MUX_GATE(ir_clk, "ir",

                                  r_mod0_default_parents, 0x1c0,
                                  0, 5,         /* M */
                                  8, 2,         /* P */
                                  24, 1,        /* mux */
                                  BIT(31),      /* gate */
                                  0);

static SUNXI_CCU_GATE(r_apb1_ir_clk, "r-apb1-ir", "r-apb1",

                      0x1cc, BIT(0), 0);

        [RST_R_APB1_IR]         =  { 0x1cc, BIT(16) },

So parent clock seems to be OK. But gate clock is not enabled, so the bus is not working.

And look at this!!:

Quoted 8 lines

static SUNXI_CCU_GATE(r_apb1_ir_clk, "r-apb1-ir", "r-apb1",

                      0x1cc, BIT(0), 0);
static SUNXI_CCU_GATE(r_apb1_w1_clk,    "r-apb1-w1",    "r-apb1",
                      0x1cc, BIT(0), 0);

So, it's wrong w1 gate config!

You can drop your changes, because I've probbably found the root cause.

Nice to see that you have found the issue, but I don't understand why It's working on my board on not on yours.

Regards,
Clément

Quoted 45 lines

regards,

        o.
Quoted 41 lines

thank you and regards,

      o.
Quoted 29 lines

Thanks,
Clément

Quoted 25 lines

thank you,

        o.
Quoted 21 lines

Regards, Clement

Quoted 13 lines

thanks,

        o.
Quoted 9 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +0 -1
              r_i2c: i2c@7081400 {
--

2.20.1

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to [email protected].
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/CAJiuCce7nHSktVsDKcR8GLRpD3WrN5yP3Nb_Hbu_Q9NjUQbSMw%40mail.gmail.com.
For more options, visit https://groups.google.com/d/optout.

Quoted 4 lines

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#21 lore raw

Re: [linux-sunxi] Re: [PATCH v3 10/12] arm64: dts: allwinner: h6: Add IR receiver node

Hi Clément,

Quoted 184 lines · Clément Péron

Hi Ondrej,

Quoted 181 lines · Ondřej Jirman

Hi Clément,

Quoted 69 lines · verejna

Hi Clément,

Quoted 66 lines · Clément Péron

Hi Ondrej,

Quoted 52 lines · Ondřej Jirman

Hello Clément,

Quoted 48 lines · Clément Péron

Hi Ondrej,

Quoted 44 lines · Ondřej Jirman

Hello Clément,

Quoted 27 lines · Clément Péron

Allwinner H6 IR is similar to A31 and can use same driver.

Add support for it.

---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +10 -0
index 16c5c3d0fd81..649cbdfe452e 100644
@@ -647,6 +647,25 @@
                              pins = "PL0", "PL1";
                              function = "s_i2c";
                      };
+
+                     r_ir_rx_pin: r-ir-rx-pin {
+                             pins = "PL9";
+                             function = "s_cir_rx";
+                     };
+             };
+
+             r_ir: ir@7040000 {
+                             compatible = "allwinner,sun50i-h6-ir",
+                                          "allwinner,sun6i-a31-ir";

arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi line 669

Quoted 10 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +9 -0
+                             reg = <0x07040000 0x400>;
+                             interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+                             clocks = <&r_ccu CLK_R_APB1_IR>,
+                                      <&r_ccu CLK_IR>;
+                             clock-names = "apb", "ir";
+                             resets = <&r_ccu RST_R_APB1_IR>;
+                             pinctrl-names = "default";
+                             pinctrl-0 = <&r_ir_rx_pin>;
+                             status = "disabled";
              };

Please make a comment here, that this is known broken on some boards and may result IRQ flood if enabled. Otherwise noone will know.

Quoted 8 lines
Quoted 5 lines

I'm planning to send a v4 next week with the IRQ_NONE return as Maxime suggested it.
https://github.com/clementperon/linux/tree/h6_ir_v4

But maybe we could also use the bit 5 of the IRQ status.

Thanks, that's nice, but that will not make the HW work. That will just disable it. The comment is still necessary.

I have pushed a new version on my github.
https://github.com/clementperon/linux/commits/h6_ir_v4

Quoted 7 lines
Quoted 1 line

I will submit it, if you are ok with it.

the changes make it worse. Console is flooded with "Temporarily disable IRQ" and other symptoms are the same as I described before. Interrupts are not disabled in a any reasonable time. (I've waited for more > 5mins already.)

You probably need to disable interrupts right away, not wait for 100k failures.

Hmm, this is what the registers look like post-probe:

R_CIR:
0x07040000 : 00000030
0x07040004 : 00000030
0x07040008 : 00000030
0x0704000c : 00000030
0x07040010 : 00000030
0x07040014 : 00000030
0x07040018 : 00000030
0x0704001c : 00000030
0x07040020 : 00000030
0x07040024 : 00000030
0x07040028 : 00000030
0x0704002c : 00000030
0x07040030 : 00000030
0x07040034 : 00000030
0x07040038 : 00000030
0x0704003c : 00000030
0x07040040 : 00000030
0x07040044 : 00000030
0x07040048 : 00000030
0x0704004c : 00000030
0x07040050 : 00000030
0x07040054 : 00000030
0x07040058 : 00000030
0x0704005c : 00000030
0x07040060 : 00000030
0x07040064 : 00000030
0x07040068 : 00000030
0x0704006c : 00000030
0x07040070 : 00000030
0x07040074 : 00000030
0x07040078 : 00000030
0x0704007c : 00000030
0x07040080 : 00000030
0x07040084 : 00000030
0x07040088 : 00000030
0x0704008c : 00000030
0x07040090 : 00000030
0x07040094 : 00000030
0x07040098 : 00000030
0x0704009c : 00000030
0x070400a0 : 00000030
0x070400a4 : 00000030
0x070400a8 : 00000030
0x070400ac : 00000030
0x070400b0 : 00000030
0x070400b4 : 00000030
0x070400b8 : 00000030
0x070400bc : 00000030
0x070400c0 : 00000030
0x070400c4 : 00000030
0x070400c8 : 00000030
0x070400cc : 00000030
0x070400d0 : 00000030
0x070400d4 : 00000030
0x070400d8 : 00000030
0x070400dc : 00000030
0x070400e0 : 00000030
0x070400e4 : 00000030
0x070400e8 : 00000030
0x070400ec : 00000030
0x070400f0 : 00000030
0x070400f4 : 00000030
0x070400f8 : 00000030
0x070400fc : 00000030

Clearly not right. It's just the R_CIR module, other modules have normal values.

I've checked:
0x070101c0 : 81000002
(IR clock config register)
0x070101cc : 00010000
(IR reset/bus clk gate reg)

static const char * const r_mod0_default_parents[] = { "osc32k", "osc24M" }; static SUNXI_CCU_MP_WITH_MUX_GATE(ir_clk, "ir",

                                  r_mod0_default_parents, 0x1c0,
                                  0, 5,         /* M */
                                  8, 2,         /* P */
                                  24, 1,        /* mux */
                                  BIT(31),      /* gate */
                                  0);

static SUNXI_CCU_GATE(r_apb1_ir_clk, "r-apb1-ir", "r-apb1",

                      0x1cc, BIT(0), 0);

        [RST_R_APB1_IR]         =  { 0x1cc, BIT(16) },

So parent clock seems to be OK. But gate clock is not enabled, so the bus is not working.

And look at this!!:

static SUNXI_CCU_GATE(r_apb1_ir_clk, "r-apb1-ir", "r-apb1",

                      0x1cc, BIT(0), 0);
static SUNXI_CCU_GATE(r_apb1_w1_clk,    "r-apb1-w1",    "r-apb1",
                      0x1cc, BIT(0), 0);
Quoted 6 lines
Quoted 3 lines

So, it's wrong w1 gate config!

You can drop your changes, because I've probbably found the root cause.

Nice to see that you have found the issue, but I don't understand why It's working on my board on not on yours.

Maybe you use modules? I have a builtin driver.

That may change initialization order. It would disable unused gates first, and when you load the module later from userpsace then it would enable the gate.

If builtin, then it would enable IR gate first, and then disable the unused gates (W1 in this case), later on when entering userspace.

Anyway, I can confirm that now, when I turn on the light in the room, I get around 10 interrupts with empty FIFO and than it stops.

It doesn't cause the flood anymore.

regards,

	o.
Quoted 53 lines

Regards,
Clément

Quoted 45 lines

regards,

        o.
Quoted 41 lines

thank you and regards,

      o.
Quoted 29 lines

Thanks,
Clément

Quoted 25 lines

thank you,

        o.
Quoted 21 lines

Regards, Clement

Quoted 13 lines

thanks,

        o.
Quoted 9 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +0 -1
              r_i2c: i2c@7081400 {
--

2.20.1

_______________________________________________
linux-arm-kernel mailing list linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected] To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/CAJiuCce7nHSktVsDKcR8GLRpD3WrN5yP3Nb_Hbu_Q9NjUQbSMw%40mail.gmail.com.
For more options, visit https://groups.google.com/d/optout.

Quoted 4 lines

_______________________________________________
linux-arm-kernel mailing list linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

_______________________________________________
linux-arm-kernel mailing list linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

_______________________________________________
linux-arm-kernel mailing list linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Signature · 4 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190604153006.g53kzhnx3hzpg5qh%40core.my.home.
For more options, visit https://groups.google.com/d/optout.
#22 lore raw

Re: [linux-sunxi] Re: [PATCH v3 10/12] arm64: dts: allwinner: h6: Add IR receiver node

Hi Ondrej,

Quoted 188 lines · Ondřej Jirman

Hi Clément,

Quoted 184 lines · Clément Péron

Hi Ondrej,

Quoted 181 lines · Ondřej Jirman

Hi Clément,

Quoted 69 lines · verejna

Hi Clément,

Quoted 66 lines · Clément Péron

Hi Ondrej,

Quoted 52 lines · Ondřej Jirman

Hello Clément,

Quoted 48 lines · Clément Péron

Hi Ondrej,

Quoted 44 lines · Ondřej Jirman

Hello Clément,

Quoted 27 lines · Clément Péron

Allwinner H6 IR is similar to A31 and can use same driver.

Add support for it.

---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +10 -0
index 16c5c3d0fd81..649cbdfe452e 100644
@@ -647,6 +647,25 @@
                              pins = "PL0", "PL1";
                              function = "s_i2c";
                      };
+
+                     r_ir_rx_pin: r-ir-rx-pin {
+                             pins = "PL9";
+                             function = "s_cir_rx";
+                     };
+             };
+
+             r_ir: ir@7040000 {
+                             compatible = "allwinner,sun50i-h6-ir",
+                                          "allwinner,sun6i-a31-ir";

arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi line 669

Quoted 10 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +9 -0
+                             reg = <0x07040000 0x400>;
+                             interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+                             clocks = <&r_ccu CLK_R_APB1_IR>,
+                                      <&r_ccu CLK_IR>;
+                             clock-names = "apb", "ir";
+                             resets = <&r_ccu RST_R_APB1_IR>;
+                             pinctrl-names = "default";
+                             pinctrl-0 = <&r_ir_rx_pin>;
+                             status = "disabled";
              };

Please make a comment here, that this is known broken on some boards and may result IRQ flood if enabled. Otherwise noone will know.

Quoted 8 lines
Quoted 5 lines

I'm planning to send a v4 next week with the IRQ_NONE return as Maxime suggested it.
https://github.com/clementperon/linux/tree/h6_ir_v4

But maybe we could also use the bit 5 of the IRQ status.

Thanks, that's nice, but that will not make the HW work. That will just disable it. The comment is still necessary.

I have pushed a new version on my github.
https://github.com/clementperon/linux/commits/h6_ir_v4

Quoted 7 lines
Quoted 1 line

I will submit it, if you are ok with it.

the changes make it worse. Console is flooded with "Temporarily disable IRQ" and other symptoms are the same as I described before. Interrupts are not disabled in a any reasonable time. (I've waited for more > 5mins already.)

You probably need to disable interrupts right away, not wait for 100k failures.

Hmm, this is what the registers look like post-probe:

R_CIR:
0x07040000 : 00000030
0x07040004 : 00000030
0x07040008 : 00000030
0x0704000c : 00000030
0x07040010 : 00000030
0x07040014 : 00000030
0x07040018 : 00000030
0x0704001c : 00000030
0x07040020 : 00000030
0x07040024 : 00000030
0x07040028 : 00000030
0x0704002c : 00000030
0x07040030 : 00000030
0x07040034 : 00000030
0x07040038 : 00000030
0x0704003c : 00000030
0x07040040 : 00000030
0x07040044 : 00000030
0x07040048 : 00000030
0x0704004c : 00000030
0x07040050 : 00000030
0x07040054 : 00000030
0x07040058 : 00000030
0x0704005c : 00000030
0x07040060 : 00000030
0x07040064 : 00000030
0x07040068 : 00000030
0x0704006c : 00000030
0x07040070 : 00000030
0x07040074 : 00000030
0x07040078 : 00000030
0x0704007c : 00000030
0x07040080 : 00000030
0x07040084 : 00000030
0x07040088 : 00000030
0x0704008c : 00000030
0x07040090 : 00000030
0x07040094 : 00000030
0x07040098 : 00000030
0x0704009c : 00000030
0x070400a0 : 00000030
0x070400a4 : 00000030
0x070400a8 : 00000030
0x070400ac : 00000030
0x070400b0 : 00000030
0x070400b4 : 00000030
0x070400b8 : 00000030
0x070400bc : 00000030
0x070400c0 : 00000030
0x070400c4 : 00000030
0x070400c8 : 00000030
0x070400cc : 00000030
0x070400d0 : 00000030
0x070400d4 : 00000030
0x070400d8 : 00000030
0x070400dc : 00000030
0x070400e0 : 00000030
0x070400e4 : 00000030
0x070400e8 : 00000030
0x070400ec : 00000030
0x070400f0 : 00000030
0x070400f4 : 00000030
0x070400f8 : 00000030
0x070400fc : 00000030

Clearly not right. It's just the R_CIR module, other modules have normal values.

I've checked:
0x070101c0 : 81000002
(IR clock config register)
0x070101cc : 00010000
(IR reset/bus clk gate reg)

static const char * const r_mod0_default_parents[] = { "osc32k", "osc24M" }; static SUNXI_CCU_MP_WITH_MUX_GATE(ir_clk, "ir",

                                  r_mod0_default_parents, 0x1c0,
                                  0, 5,         /* M */
                                  8, 2,         /* P */
                                  24, 1,        /* mux */
                                  BIT(31),      /* gate */
                                  0);

static SUNXI_CCU_GATE(r_apb1_ir_clk, "r-apb1-ir", "r-apb1",

                      0x1cc, BIT(0), 0);

        [RST_R_APB1_IR]         =  { 0x1cc, BIT(16) },

So parent clock seems to be OK. But gate clock is not enabled, so the bus is not working.

And look at this!!:

static SUNXI_CCU_GATE(r_apb1_ir_clk, "r-apb1-ir", "r-apb1",

                      0x1cc, BIT(0), 0);
static SUNXI_CCU_GATE(r_apb1_w1_clk,    "r-apb1-w1",    "r-apb1",
                      0x1cc, BIT(0), 0);
Quoted 8 lines
Quoted 6 lines
Quoted 3 lines

So, it's wrong w1 gate config!

You can drop your changes, because I've probbably found the root cause.

Nice to see that you have found the issue, but I don't understand why It's working on my board on not on yours.

Maybe you use modules? I have a builtin driver.

Correct,

Quoted 6 lines

That may change initialization order. It would disable unused gates first, and when you load the module later from userpsace then it would enable the gate.

If builtin, then it would enable IR gate first, and then disable the unused gates (W1 in this case), later on when entering userspace.

Thanks for the explanation it makes sense.

Quoted 3 lines

Anyway, I can confirm that now, when I turn on the light in the room, I get around 10 interrupts with empty FIFO and than it stops.

Ok I will push a V4 with just the introduction of the RXSTA.

Regards,
Clément

Quoted 59 lines

It doesn't cause the flood anymore.

regards,

        o.
Quoted 53 lines

Regards,
Clément

Quoted 45 lines

regards,

        o.
Quoted 41 lines

thank you and regards,

      o.
Quoted 29 lines

Thanks,
Clément

Quoted 25 lines

thank you,

        o.
Quoted 21 lines

Regards, Clement

Quoted 13 lines

thanks,

        o.
Quoted 9 lines
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +0 -1
              r_i2c: i2c@7081400 {
--

2.20.1

_______________________________________________
linux-arm-kernel mailing list linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected] To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/CAJiuCce7nHSktVsDKcR8GLRpD3WrN5yP3Nb_Hbu_Q9NjUQbSMw%40mail.gmail.com.
For more options, visit https://groups.google.com/d/optout.

Quoted 4 lines

_______________________________________________
linux-arm-kernel mailing list linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

_______________________________________________
linux-arm-kernel mailing list linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

_______________________________________________
linux-arm-kernel mailing list linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Signature · 4 lines
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/CAJiuCcc1D1RVdpZG4bEeYWbCr8isWfP-2O9DAt-%2BavcrSp0f9Q%40mail.gmail.com.
For more options, visit https://groups.google.com/d/optout.
#23 lore raw

PATCH v3 11/12 arm64: dts: allwinner: h6: Enable IR on Beelink GS1

In reply to Clément Péron

Beelink GS1 has an IR receiver.

Enable it in the device-tree.

---
 arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts +4 -0
index 0dc33c90dd60..680dc29cb089 100644
@@ -232,6 +232,10 @@
 	};
 };
 
+&r_ir {
+	status = "okay";
+};
+
 &r_pio {
 	/*
 	 * PL0 and PL1 are used for PMIC I2C
Signature · 7 lines
2.20.1

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/[email protected]
To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/20190528161440.27172-12-peron.clem%40gmail.com.
For more options, visit https://groups.google.com/d/optout.
#24 lore raw

PATCH v3 12/12 arm64: defconfig: enable IR SUNXI option

In reply to Clément Péron

Enable CONFIG_IR_SUNXI option for ARM64, so that Allwinner A64/H6 SoCs can use their IR receiver controller.

---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/configs/defconfig +1 -0
index 4d583514258c..5128029100d2 100644
@@ -460,6 +460,7 @@ CONFIG_RC_CORE=m
 CONFIG_RC_DECODERS=y
 CONFIG_RC_DEVICES=y
 CONFIG_IR_MESON=m
+CONFIG_IR_SUNXI=m
 CONFIG_MEDIA_SUPPORT=m
 CONFIG_MEDIA_CAMERA_SUPPORT=y
 CONFIG_MEDIA_ANALOG_TV_SUPPORT=y
Signature · 1 line
2.20.1
maintainer Acked-by on the v3 series
#25 lore raw
In reply to Clément Péron
Quoted 5 lines · Clément Péron

Hi,

A64 IR support series[1] pointed out that an A31 bindings should be introduced.

Quoted 7 lines

This series introduce the A31 compatible bindings, then switch it on the already existing board.

Finally introduce A64 and H6 support.

I didn't enable the IR on other H6 boards as Ondrej reported an issue on his board[2].

For the whole series:

Quoted 50 lines

Regards,
Clément

[1] https://lore.kernel.org/patchwork/patch/1031390/#1221464
[2] https://lkml.org/lkml/2019/5/27/321

Changes since v2:
- Disable IR for other H6 boards
- Split DTS patch for H3/H5
- Introduce IR quirks

Changes since v1:
- Document reset lines as required since A31
- Explain the memory mapping difference in commit log
- Fix misspelling "Allwiner" to "Allwinner"

Clément Péron (10):
dt-bindings: media: sunxi-ir: add A31 compatible
media: rc: Introduce sunxi_ir_quirks
media: rc: sunxi: Add A31 compatible
ARM: dts: sunxi: Prefer A31 bindings for IR
ARM: dts: sunxi: Prefer A31 bindings for IR
dt-bindings: media: sunxi-ir: Add A64 compatible
dt-bindings: media: sunxi-ir: Add H6 compatible
arm64: dts: allwinner: h6: Add IR receiver node
arm64: dts: allwinner: h6: Enable IR on Beelink GS1
arm64: defconfig: enable IR SUNXI option

Igors Makejevs (1):
arm64: dts: allwinner: a64: Add IR node

Jernej Skrabec (1):
arm64: dts: allwinner: a64: Enable IR on Orange Pi Win

 .../devicetree/bindings/media/sunxi-ir.txt    | 11 ++-
 arch/arm/boot/dts/sun6i-a31.dtsi              |  2 +-
 arch/arm/boot/dts/sun8i-a83t.dtsi             |  2 +-
 arch/arm/boot/dts/sun9i-a80.dtsi              |  2 +-
 arch/arm/boot/dts/sunxi-h3-h5.dtsi            |  2 +-
 .../dts/allwinner/sun50i-a64-orangepi-win.dts |  4 ++
 arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 18 +++++
 .../dts/allwinner/sun50i-h6-beelink-gs1.dts   |  4 ++
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi  | 19 +++++
 arch/arm64/configs/defconfig                  |  1 +
 drivers/media/rc/sunxi-cir.c                  | 70 +++++++++++++++----
 11 files changed, 115 insertions(+), 20 deletions(-)
Signature · 1 line
2.20.1