arm64: Add initial support for Odroid-N2
Subsystems (2)
v5 cover arm64: Add initial support for Odroid-N2
This patchset adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoC
The Amlogic G12B SoC is very similar with the G12A SoC, sharing most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
Actual support is done in the same way as for the GXM support, including the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove the last 2 cpu nodes of the first cluster.
Dependencies :
- Patch 1, 2 : YAML rewrite of amlogic.txt bindings at [7]
- Patch 3 : None since clock + g12b bindings has been acked
Changes since v4 at [9]:
- Fix regulators for USB Host
Changes since v3 at [8]:
- Dropped arm,armv8
- Dropped eee disable, not needed in further tests
- Add comments about where are connected the regulators pins
- Moved the phy0 regulator to the usb vbus regulator
Changes since v2 at [5]:
- sent the clk patches in standalone at [6]
- rewrote the bindings on top of the YAML rewrite at [7]
- Added MMC, SDCard and Network support to Odroid-N2
Changes since v1 at [3]:
- Renamed the g12b cpu clocks like g12a counterparts
- Rebased clock patches on top of Guillaume's Temperature sensor Clock patches at [4]
- Added AO-CEC-B support to N2 DTS
Changes since RFC at [1]:
- Added bindings review tags
- Moved the fclk_div3 CRITICAL flags to the gate
- Removed invalid CRITICAL flags on the cpu clocks
[1] https://lkml.kernel.org/r/[email protected]
[2] https://lkml.kernel.org/r/[email protected]
[3] https://lkml.kernel.org/r/[email protected]
[4] https://lkml.kernel.org/r/[email protected]
[5] https://lkml.kernel.org/r/[email protected]
[6] https://lkml.kernel.org/r/[email protected]
[7] https://lkml.kernel.org/r/[email protected]
[8] https://lkml.kernel.org/r/[email protected]
[9] https://lkml.kernel.org/r/[email protected]
Neil Armstrong (3):
dt-bindings: arm: amlogic: add G12B bindings
dt-bindings: arm: amlogic: add Odroid-N2 binding
arm64: dts: meson: Add minimal support for Odroid-N2
.../devicetree/bindings/arm/amlogic.yaml | 6 + arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 289 ++++++++++++++++++ arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 82 +++++ 4 files changed, 378 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
Signature · 7 lines
2.21.0 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 1/3 dt-bindings: arm: amlogic: add G12B bindings
Add compatible for the Amlogic G12B SoC, sharing most of the features and architecture with the G12A SoC.
--- Documentation/devicetree/bindings/arm/amlogic.yaml | 4 ++++ 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/arm/amlogic.yaml +4 -0
@@ -137,4 +137,8 @@ properties: - amlogic,u200 - const: amlogic,g12a + - description: Boards with the Amlogic Meson G12B S922X SoC + items: + - const: amlogic,g12b + ...
Signature · 1 line
2.21.0
PATCH v5 2/3 dt-bindings: arm: amlogic: add Odroid-N2 binding
In reply to Neil ArmstrongAdd compatible for the Amlogic G12B (S922X) SoC based Odroid-N2 SBC from HardKernel.
--- Documentation/devicetree/bindings/arm/amlogic.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/arm/amlogic.yaml +2 -0
@@ -139,6 +139,8 @@ properties: - description: Boards with the Amlogic Meson G12B S922X SoC items: + - enum: + - hardkernel,odroid-n2 - const: amlogic,g12b ...
Signature · 1 line
2.21.0
PATCH v5 3/3 arm64: dts: meson: Add minimal support for Odroid-N2
In reply to Neil ArmstrongThis patch adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoC
The Amlogic G12B SoC is very similar with the G12A SoC, sharing most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
Actual support is done in the same way as for the GXM support, including the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove the last 2 cpu nodes of the first cluster.
--- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 289 ++++++++++++++++++ arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 82 +++++ 3 files changed, 372 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsi
arch/arm64/boot/dts/amlogic/Makefile +1 -0
@@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtb
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts new file +289 -0
289 lines not on this page · raw message
arch/arm64/boot/dts/amlogic/meson-g12b.dtsi new file +82 -0
82 lines not on this page · raw message
Signature · 1 line
2.21.0
Re: [PATCH v5 3/3] arm64: dts: meson: Add minimal support for Odroid-N2
Hi Niel,
Quoted 131 lines · Neil Armstrong
This patch adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoCThe Amlogic G12B SoC is very similar with the G12A SoC, sharing most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the sameActual support is done in the same way as for the GXM support, including the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove the last 2 cpu nodes of the first cluster.Signed-off-by Neil Armstrong <[email protected]>Reviewed-by Martin Blumenstingl <[email protected]>--- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 289 ++++++++++++++++++ arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 82 +++++ 3 files changed, 372 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsiarch/arm64/boot/dts/amlogic/Makefile +1
-0@@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtbarch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts new file +83
-0@@ -0,0 +1,289 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <[email protected]> + */ + +/dts-v1/; + +#include "meson-g12b.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/meson-g12a-gpio.h> + +/ { + compatible = "hardkernel,odroid-n2", "amlogic,g12b"; + model = "Hardkernel ODROID-N2"; + + aliases { + serial0 = &uart_AO; + ethernet0 = ðmac; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x40000000>; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>; + }; + + leds { + compatible = "gpio-leds"; + + blue { + label = "n2:blue"; + gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + tflash_vdd: regulator-tflash_vdd { + compatible = "regulator-fixed"; + + regulator-name = "TFLASH_VDD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + tf_io: gpio-regulator-tf_io { + compatible = "regulator-gpio"; + + regulator-name = "TF_IO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>; + gpios-states = <0>; + + states = <3300000 0 + 1800000 1>; + }; + + flash_1v8: regulator-flash_1v8 { + compatible = "regulator-fixed"; + regulator-name = "FLASH_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_3v3>; + regulator-always-on; + }; + + main_12v: regulator-main_12v { + compatible = "regulator-fixed"; + regulator-name = "12V"; + regulator-min-microvolt = <12000000>;
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts line 93
Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts new file +10
-0+ regulator-max-microvolt = <12000000>; + regulator-always-on; + }; + + vcc_5v: regulator-vcc_5v { + compatible = "regulator-fixed"; + regulator-name = "5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on;
As per odroid-n2_rev0.4_20190307 schematic its missing.
vin-supply = <&main_12v>;
With this please add my.
Best Regards
-Anand
Quoted 292 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts new file +196
-0+ }; + + vcc_1v8: regulator-vcc_1v8 { + compatible = "regulator-fixed"; + regulator-name = "VCC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_3v3>; + regulator-always-on; + }; + + vcc_3v3: regulator-vcc_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + /* FIXME: actually controlled by VDDCPU_B_EN */ + }; + + hub_5v: regulator-hub_5v { + compatible = "regulator-fixed"; + regulator-name = "HUB_5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc_5v>; + + /* Connected to the Hub CHIPENABLE, LOW sets low power state */ + gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + usb_pwr_en: regulator-usb_pwr_en { + compatible = "regulator-fixed"; + regulator-name = "USB_PWR_EN"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc_5v>; + + /* Connected to the microUSB port power enable */ + gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + vddao_1v8: regulator-vddao_1v8 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + }; + + vddao_3v3: regulator-vddao_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&main_12v>; + regulator-always-on; + }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_tx_tmds_out>; + }; + }; + }; +}; + +&cec_AO { + pinctrl-0 = <&cec_ao_a_h_pins>; + pinctrl-names = "default"; + status = "disabled"; + hdmi-phandle = <&hdmi_tx>; +}; + +&cecb_AO { + pinctrl-0 = <&cec_ao_b_h_pins>; + pinctrl-names = "default"; + status = "okay"; + hdmi-phandle = <&hdmi_tx>; +}; + +&ext_mdio { + external_phy: ethernet-phy@0 { + /* Realtek RTL8211F (0x001cc916) */ + reg = <0>; + max-speed = <1000>; + }; +}; + +ðmac { + pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; + pinctrl-names = "default"; + status = "okay"; + phy-mode = "rgmii"; + phy-handle = <&external_phy>; + amlogic,tx-delay-ns = <2>; +}; + +&gpio { + /* + * WARNING: The USB Hub on the Odroid-N2 needs a reset signal + * to be turned high in order to be detected by the USB Controller + * This signal should be handled by a USB specific power sequence + * in order to reset the Hub when USB bus is powered down. + */ + usb-hub { + gpio-hog; + gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "usb-hub-reset"; + }; +}; + +&hdmi_tx { + status = "okay"; + pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>; + pinctrl-names = "default"; + hdmi-supply = <&vcc_5v>; +}; + +&hdmi_tx_tmds_port { + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; +}; + +&ir { + status = "okay"; + pinctrl-0 = <&remote_input_ao_pins>; + pinctrl-names = "default"; +}; + +/* SD card */ +&sd_emmc_b { + status = "okay"; + pinctrl-0 = <&sdcard_c_pins>; + pinctrl-1 = <&sdcard_clk_gate_c_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <50000000>; + disable-wp; + + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; + vmmc-supply = <&tflash_vdd>; + vqmmc-supply = <&tf_io>; + +}; + +/* eMMC */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>; + pinctrl-1 = <&emmc_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <8>; + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + max-frequency = <200000000>; + disable-wp; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&flash_1v8>; +}; + +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +&usb { + status = "okay"; + vbus-supply = <&usb_pwr_en>; +}; + +&usb2_phy0 { + phy-supply = <&vcc_5v>; +}; + +&usb2_phy1 { + /* Enable the hub which is connected to this port */ + phy-supply = <&hub_5v>; +};arch/arm64/boot/dts/amlogic/meson-g12b.dtsi new file +82
-1@@ -0,0 +1,82 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <[email protected]> + */ + +#include "meson-g12a.dtsi" + +/ { + compatible = "amlogic,g12b"; + + cpus { + cpu-map { + cluster0 { + core0 { + cpu = <&cpu0>; + }; + + core1 { + cpu = <&cpu1>; + }; + }; + + cluster1 { + core0 { + cpu = <&cpu100>; + }; + + core1 { + cpu = <&cpu101>; + }; + + core2 { + cpu = <&cpu102>; + }; + + core3 { + cpu = <&cpu103>; + }; + }; + }; + + /delete-node/ cpu@2; + /delete-node/ cpu@3; + + cpu100: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a73"; + reg = <0x0 0x100>; + enable-method = "psci"; + next-level-cache = <&l2>; + }; + + cpu101: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a73"; + reg = <0x0 0x101>; + enable-method = "psci"; + next-level-cache = <&l2>; + }; + + cpu102: cpu@102 { + device_type = "cpu"; + compatible = "arm,cortex-a73"; + reg = <0x0 0x102>; + enable-method = "psci"; + next-level-cache = <&l2>; + }; + + cpu103: cpu@103 { + device_type = "cpu"; + compatible = "arm,cortex-a73"; + reg = <0x0 0x103>; + enable-method = "psci"; + next-level-cache = <&l2>; + }; + }; +}; + +&clkc { + compatible = "amlogic,g12b-clkc"; +}; --2.21.0
_______________________________________________
linux-amlogic mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-amlogic
Re: [PATCH v5 3/3] arm64: dts: meson: Add minimal support for Odroid-N2
Quoted 72 lines · Anand Moon
Hi Niel,
Quoted 69 lines · Neil Armstrong
This patch adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoCThe Amlogic G12B SoC is very similar with the G12A SoC, sharing most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the sameActual support is done in the same way as for the GXM support, including the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove the last 2 cpu nodes of the first cluster.Signed-off-by Neil Armstrong <[email protected]>Reviewed-by Martin Blumenstingl <[email protected]>--- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 289 ++++++++++++++++++ arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 82 +++++ 3 files changed, 372 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsiarch/arm64/boot/dts/amlogic/Makefile +1
-0@@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtbarch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts new file +21
-0@@ -0,0 +1,289 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <[email protected]> + */ + +/dts-v1/; + +#include "meson-g12b.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/meson-g12a-gpio.h> + +/ { + compatible = "hardkernel,odroid-n2", "amlogic,g12b"; + model = "Hardkernel ODROID-N2"; + + aliases { + serial0 = &uart_AO; + ethernet0 = ðmac; + }; +
[...]
Quoted 17 lines
Quoted 5 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts new file +5
-0+ + main_12v: regulator-main_12v { + compatible = "regulator-fixed"; + regulator-name = "12V"; + regulator-min-microvolt = <12000000>;arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts line 93
Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts new file +10
-0+ regulator-max-microvolt = <12000000>; + regulator-always-on; + }; + + vcc_5v: regulator-vcc_5v { + compatible = "regulator-fixed"; + regulator-name = "5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on;As per odroid-n2_rev0.4_20190307 schematic its missing.
Quoted 4 lines
vin-supply = <&main_12v>;With this please add my.
Tested-by Anand Moon <[email protected]>
Good catch, thanks Anand.
@Kevin, should I resend ?
Neil
Quoted 14 lines
Best Regards
-AnandQuoted 11 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts new file +11
-0+ }; + + vcc_1v8: regulator-vcc_1v8 { + compatible = "regulator-fixed"; + regulator-name = "VCC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_3v3>; + regulator-always-on; + }; +
[...]
Quoted 12 lines
Quoted 12 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts new file +4
-1+ +&clkc { + compatible = "amlogic,g12b-clkc"; +}; --2.21.0
_______________________________________________
linux-amlogic mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-amlogic
Kevin Hilman
maintainerRe: [PATCH v5 3/3] arm64: dts: meson: Add minimal support for Odroid-N2
Quoted 95 lines · Neil Armstrong
Quoted 72 lines · Anand Moon
Hi Niel,
Quoted 69 lines · Neil Armstrong
This patch adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoCThe Amlogic G12B SoC is very similar with the G12A SoC, sharing most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the sameActual support is done in the same way as for the GXM support, including the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove the last 2 cpu nodes of the first cluster.Signed-off-by Neil Armstrong <[email protected]>Reviewed-by Martin Blumenstingl <[email protected]>--- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 289 ++++++++++++++++++ arch/arm64/boot/dts/amlogic/meson-g12b.dtsi | 82 +++++ 3 files changed, 372 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b.dtsiarch/arm64/boot/dts/amlogic/Makefile +1
-0@@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtbarch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts new file +21
-0@@ -0,0 +1,289 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <[email protected]> + */ + +/dts-v1/; + +#include "meson-g12b.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/meson-g12a-gpio.h> + +/ { + compatible = "hardkernel,odroid-n2", "amlogic,g12b"; + model = "Hardkernel ODROID-N2"; + + aliases { + serial0 = &uart_AO; + ethernet0 = ðmac; + }; +[...]
Quoted 19 lines
Quoted 5 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts new file +5
-0+ + main_12v: regulator-main_12v { + compatible = "regulator-fixed"; + regulator-name = "12V"; + regulator-min-microvolt = <12000000>;arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts line 93
Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts new file +10
-0+ regulator-max-microvolt = <12000000>; + regulator-always-on; + }; + + vcc_5v: regulator-vcc_5v { + compatible = "regulator-fixed"; + regulator-name = "5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on;As per odroid-n2_rev0.4_20190307 schematic its missing.
vin-supply = <&main_12v>;
Quoted 6 lines
Quoted 2 lines
With this please add my.
Tested-by Anand Moon <[email protected]>Good catch, thanks Anand.
@Kevin, should I resend ?
No need, I've fixed it up locally,
Thanks,
Kevin
Quoted 14 lines · Neil Armstrong
This patchset adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoCThe Amlogic G12B SoC is very similar with the G12A SoC, sharing most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
Quoted 4 lines
Actual support is done in the same way as for the GXM support, including the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove the last 2 cpu nodes of the first cluster.
Queued for v5.3,
Kevin