Skip to contentSkip to conversation

spl: dm: disable SPI DM flash for non-DM SPL

PATCH Superseded Chuanhua Han 3 participants 15 messages May 24, 2019 – Jun 24, 2019

Subsystems (2)

v2 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/5 spl: dm: disable SPI DM flash for non-DM SPL

This patch solves the problem that spiboot cannot be performed in non-DM SPL.

---
Changes in v2:
- No change.

 include/config_uncmd_spl.h | 1 +
 1 file changed, 1 insertion(+)
include/config_uncmd_spl.h +1 -0
index c2f9735ce7..da94b3d9df 100644
@@ -15,6 +15,7 @@
 #undef CONFIG_DM_GPIO
 #undef CONFIG_DM_I2C
 #undef CONFIG_DM_SPI
+#undef CONFIG_DM_SPI_FLASH
 #endif
 
 #undef CONFIG_DM_WARN
Signature · 1 line
2.17.1
#1 lore raw

PATCH v2 2/5 dm: spi: Convert Freescale ESPI driver to driver model

Modify the Freescale ESPI driver to support the driver model. Also resolved the following problems:

===================== WARNING ====================== This board does not use CONFIG_DM_SPI. Please update the board before v2019.04 for no dm conversion
and v2019.07 for partially dm converted drivers. Failure to update can lead to driver/board removal See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ====================== This board does not use CONFIG_DM_SPI_FLASH. Please update the board to use CONFIG_SPI_FLASH before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info.
====================================================

---
Changes in v2:
- The fsl_espi driver support both OF_CONTROL and PLATDATA

 drivers/spi/fsl_espi.c | 454 +++++++++++++++++++++++++++++------------
 1 file changed, 320 insertions(+), 134 deletions(-)
drivers/spi/fsl_espi.c +320 -134
index 7444ae1a06..a2f4027fca 100644
@@ -4,17 +4,27 @@
  *
  * Copyright 2010-2011 Freescale Semiconductor, Inc.
  * Author: Mingkai Hu (Mingkai.hu at freescale.com)
+ *	   Chuanhua Han (chuanhua.han at nxp.com)
  */
 
 #include <common.h>
-
 #include <malloc.h>
 #include <spi.h>
 #include <asm/immap_85xx.h>
+#include <dm.h>
+#include <errno.h>
+#include <fdtdec.h>
+
+struct fsl_espi_platdata {
+	uint flags;
+	uint speed_hz;
+	uint num_chipselect;
+	fdt_addr_t regs_addr;
+};
 
-struct fsl_spi_slave {
-	struct spi_slave slave;
+struct fsl_espi_priv {
 	ccsr_espi_t	*espi;
+	u32 speed_hz;
 	unsigned int	div16;
 	unsigned int	pm;
 	int		tx_timeout;
@@ -25,9 +35,18 @@ struct fsl_spi_slave {
 	unsigned int    max_transfer_length;
 };
 
+struct fsl_spi_slave {
+	struct spi_slave slave;
+	struct fsl_espi_priv priv;
+};
+
 #define to_fsl_spi_slave(s) container_of(s, struct fsl_spi_slave, slave)
+#define to_fsl_spi_priv(p) container_of(p, struct fsl_spi_slave, priv)
 #define US_PER_SECOND		1000000UL
 
+/* default SCK frequency, unit: HZ */
+#define FSL_ESPI_DEFAULT_SCK_FREQ   10000000
+
 #define ESPI_MAX_CS_NUM		4
 #define ESPI_FIFO_WIDTH_BIT	32
 
@@ -62,121 +81,46 @@ struct fsl_spi_slave {
 
 #define ESPI_MAX_DATA_TRANSFER_LEN 0xFFF0
 
-struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
-		unsigned int max_hz, unsigned int mode)
-{
-	struct fsl_spi_slave *fsl;
-	sys_info_t sysinfo;
-	unsigned long spibrg = 0;
-	unsigned long spi_freq = 0;
-	unsigned char pm = 0;
-
-	if (!spi_cs_is_valid(bus, cs))
-		return NULL;
-
-	fsl = spi_alloc_slave(struct fsl_spi_slave, bus, cs);
-	if (!fsl)
-		return NULL;
-
-	fsl->espi = (void *)(CONFIG_SYS_MPC85xx_ESPI_ADDR);
-	fsl->mode = mode;
-	fsl->max_transfer_length = ESPI_MAX_DATA_TRANSFER_LEN;
-
-	/* Set eSPI BRG clock source */
-	get_sys_info(&sysinfo);
-	spibrg = sysinfo.freq_systembus / 2;
-	fsl->div16 = 0;
-	if ((spibrg / max_hz) > 32) {
-		fsl->div16 = ESPI_CSMODE_DIV16;
-		pm = spibrg / (max_hz * 16 * 2);
-		if (pm > 16) {
-			pm = 16;
-			debug("Requested speed is too low: %d Hz, %ld Hz "
-				"is used.\n", max_hz, spibrg / (32 * 16));
-		}
-	} else
-		pm = spibrg / (max_hz * 2);
-	if (pm)
-		pm--;
-	fsl->pm = pm;
-
-	if (fsl->div16)
-		spi_freq = spibrg / ((pm + 1) * 2 * 16);
-	else
-		spi_freq = spibrg / ((pm + 1) * 2);
-
-	/* set tx_timeout to 10 times of one espi FIFO entry go out */
-	fsl->tx_timeout = DIV_ROUND_UP((US_PER_SECOND * ESPI_FIFO_WIDTH_BIT
-				* 10), spi_freq);
-
-	return &fsl->slave;
-}
-
-void spi_free_slave(struct spi_slave *slave)
+#ifndef CONFIG_DM_SPI
+void spi_cs_activate(struct spi_slave *slave)
 {
 	struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
-	free(fsl);
-}
+	ccsr_espi_t *espi = fsl->priv.espi;
+	unsigned int com = 0;
+	size_t data_len = fsl->priv.data_len;
 
-int spi_claim_bus(struct spi_slave *slave)
+	com &= ~(ESPI_COM_CS(0x3) | ESPI_COM_TRANLEN(0xFFFF));
+	com |= ESPI_COM_CS(slave->cs);
+	com |= ESPI_COM_TRANLEN(data_len - 1);
+	out_be32(&espi->com, com);
+}
+#else
+void fsl_spi_cs_activate(struct fsl_espi_priv *priv,  uint cs)
 {
-	struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
-	ccsr_espi_t *espi = fsl->espi;
-	unsigned char pm = fsl->pm;
-	unsigned int cs = slave->cs;
-	unsigned int mode =  fsl->mode;
-	unsigned int div16 = fsl->div16;
-	int i;
-
-	debug("%s: bus:%i cs:%i\n", __func__, slave->bus, cs);
-
-	/* Enable eSPI interface */
-	out_be32(&espi->mode, ESPI_MODE_RXTHR(3)
-			| ESPI_MODE_TXTHR(4) | ESPI_MODE_EN);
-
-	out_be32(&espi->event, 0xffffffff); /* Clear all eSPI events */
-	out_be32(&espi->mask, 0x00000000); /* Mask  all eSPI interrupts */
-
-	/* Init CS mode interface */
-	for (i = 0; i < ESPI_MAX_CS_NUM; i++)
-		out_be32(&espi->csmode[i], ESPI_CSMODE_INIT_VAL);
-
-	out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs]) &
-		~(ESPI_CSMODE_PM(0xF) | ESPI_CSMODE_DIV16
-		| ESPI_CSMODE_CI_INACTIVEHIGH | ESPI_CSMODE_CP_BEGIN_EDGCLK
-		| ESPI_CSMODE_REV_MSB_FIRST | ESPI_CSMODE_LEN(0xF)));
-
-	/* Set eSPI BRG clock source */
-	out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-		| ESPI_CSMODE_PM(pm) | div16);
-
-	/* Set eSPI mode */
-	if (mode & SPI_CPHA)
-		out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-			| ESPI_CSMODE_CP_BEGIN_EDGCLK);
-	if (mode & SPI_CPOL)
-		out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-			| ESPI_CSMODE_CI_INACTIVEHIGH);
-
-	/* Character bit order: msb first */
-	out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-		| ESPI_CSMODE_REV_MSB_FIRST);
-
-	/* Character length in bits, between 0x3~0xf, i.e. 4bits~16bits */
-	out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-		| ESPI_CSMODE_LEN(7));
+	ccsr_espi_t *espi = priv->espi;
+	unsigned int com = 0;
+	size_t data_len = priv->data_len;
 
-	return 0;
+	com &= ~(ESPI_COM_CS(0x3) | ESPI_COM_TRANLEN(0xFFFF));
+	com |= ESPI_COM_CS(cs);
+	com |= ESPI_COM_TRANLEN(data_len - 1);
+	out_be32(&espi->com, com);
 }
+#endif
 
-void spi_release_bus(struct spi_slave *slave)
+void spi_cs_deactivate(struct spi_slave *slave)
 {
+	struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
+	ccsr_espi_t *espi = fsl->priv.espi;
 
+	/* clear the RXCNT and TXCNT */
+	out_be32(&espi->mode, in_be32(&espi->mode) & (~ESPI_MODE_EN));
+	out_be32(&espi->mode, in_be32(&espi->mode) | ESPI_MODE_EN);
 }
 
-static void fsl_espi_tx(struct fsl_spi_slave *fsl, const void *dout)
+static void fsl_espi_tx(struct fsl_espi_priv *priv, const void *dout)
 {
-	ccsr_espi_t *espi = fsl->espi;
+	ccsr_espi_t *espi = priv->espi;
 	unsigned int tmpdout, event;
 	int tmp_tx_timeout;
 
@@ -189,7 +133,7 @@ static void fsl_espi_tx(struct fsl_spi_slave *fsl, const void *dout)
 	out_be32(&espi->event, ESPI_EV_TNF);
 	debug("***spi_xfer:...%08x written\n", tmpdout);
 
-	tmp_tx_timeout = fsl->tx_timeout;
+	tmp_tx_timeout = priv->tx_timeout;
 	/* Wait for eSPI transmit to go out */
 	while (tmp_tx_timeout--) {
 		event = in_be32(&espi->event);
@@ -204,9 +148,10 @@ static void fsl_espi_tx(struct fsl_spi_slave *fsl, const void *dout)
 		debug("***spi_xfer:...Tx timeout! event = %08x\n", event);
 }
 
-static int fsl_espi_rx(struct fsl_spi_slave *fsl, void *din, unsigned int bytes)
+static int fsl_espi_rx(struct fsl_espi_priv *priv, void *din,
+		       unsigned int bytes)
 {
-	ccsr_espi_t *espi = fsl->espi;
+	ccsr_espi_t *espi = priv->espi;
 	unsigned int tmpdin, rx_times;
 	unsigned char *buf, *p_cursor;
 
@@ -236,11 +181,12 @@ static int fsl_espi_rx(struct fsl_spi_slave *fsl, void *din, unsigned int bytes)
 	return bytes;
 }
 
-int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *data_out,
-		void *data_in, unsigned long flags)
+int espi_xfer(struct fsl_espi_priv *priv,  uint cs, unsigned int bitlen,
+	      const void *data_out, void *data_in, unsigned long flags)
 {
-	struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
-	ccsr_espi_t *espi = fsl->espi;
+	struct fsl_spi_slave *fsl = to_fsl_spi_priv(priv);
+	struct spi_slave *slave = &fsl->slave;
+	ccsr_espi_t *espi = priv->espi;
 	unsigned int event, rx_bytes;
 	const void *dout = NULL;
 	void *din = NULL;
@@ -249,16 +195,17 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *data_out,
 	int num_bytes;
 	unsigned char *buffer = NULL;
 	size_t buf_len;
-	u8 *cmd_buf = fsl->cmd_buf;
-	size_t cmd_len = fsl->cmd_len;
+	u8 *cmd_buf = priv->cmd_buf;
+	size_t cmd_len = priv->cmd_len;
 	size_t data_len = bitlen / 8;
 	size_t rx_offset = 0;
 	int rf_cnt;
 
-	max_tran_len = fsl->max_transfer_length;
+	max_tran_len = priv->max_transfer_length;
 	switch (flags) {
 	case SPI_XFER_BEGIN:
-		cmd_len = fsl->cmd_len = data_len;
+		cmd_len = data_len;
+		priv->cmd_len = cmd_len;
 		memcpy(cmd_buf, data_out, cmd_len);
 		return 0;
 	case 0:
@@ -303,8 +250,13 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *data_out,
 		tran_len = min(data_len, (size_t)max_tran_len);
 		num_blks = DIV_ROUND_UP(tran_len + cmd_len, 4);
 		num_bytes = (tran_len + cmd_len) % 4;
-		fsl->data_len = tran_len + cmd_len;
-		spi_cs_activate(slave);
+		priv->data_len = tran_len + cmd_len;
+		#ifdef CONFIG_DM_SPI
+			fsl_spi_cs_activate(priv, cs);
+		#else
+			spi_cs_activate(slave);
+		#endif
+
 
 		/* Clear all eSPI events */
 		out_be32(&espi->event , 0xffffffff);
@@ -312,7 +264,7 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *data_out,
 		while (num_blks) {
 			event = in_be32(&espi->event);
 			if (event & ESPI_EV_TNF) {
-				fsl_espi_tx(fsl, dout);
+				fsl_espi_tx(priv, dout);
 				/* Set up the next iteration */
 				if (len > 4) {
 					len -= 4;
@@ -330,7 +282,7 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *data_out,
 					rx_bytes = num_bytes;
 				else
 					continue;
-				if (fsl_espi_rx(fsl, din, rx_bytes)
+				if (fsl_espi_rx(priv, din, rx_bytes)
 						== rx_bytes) {
 					num_blks--;
 					if (din)
@@ -354,30 +306,264 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *data_out,
 	return 0;
 }
 
+void espi_claim_bus(struct fsl_espi_priv *priv, unsigned int cs)
+{
+	ccsr_espi_t *espi = priv->espi;
+	unsigned char pm = priv->pm;
+	unsigned int mode =  priv->mode;
+	unsigned int div16 = priv->div16;
+	int i;
+
+	/* Enable eSPI interface */
+	out_be32(&espi->mode, ESPI_MODE_RXTHR(3)
+			| ESPI_MODE_TXTHR(4) | ESPI_MODE_EN);
+
+	out_be32(&espi->event, 0xffffffff); /* Clear all eSPI events */
+	out_be32(&espi->mask, 0x00000000); /* Mask  all eSPI interrupts */
+
+	/* Init CS mode interface */
+	for (i = 0; i < ESPI_MAX_CS_NUM; i++)
+		out_be32(&espi->csmode[i], ESPI_CSMODE_INIT_VAL);
+
+	out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs]) &
+		~(ESPI_CSMODE_PM(0xF) | ESPI_CSMODE_DIV16
+		| ESPI_CSMODE_CI_INACTIVEHIGH | ESPI_CSMODE_CP_BEGIN_EDGCLK
+		| ESPI_CSMODE_REV_MSB_FIRST | ESPI_CSMODE_LEN(0xF)));
+
+	/* Set eSPI BRG clock source */
+	out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
+		| ESPI_CSMODE_PM(pm) | div16);
+
+	/* Set eSPI mode */
+	if (mode & SPI_CPHA)
+		out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
+			| ESPI_CSMODE_CP_BEGIN_EDGCLK);
+	if (mode & SPI_CPOL)
+		out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
+			| ESPI_CSMODE_CI_INACTIVEHIGH);
+
+	/* Character bit order: msb first */
+	out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
+		| ESPI_CSMODE_REV_MSB_FIRST);
+
+	/* Character length in bits, between 0x3~0xf, i.e. 4bits~16bits */
+	out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
+		| ESPI_CSMODE_LEN(7));
+}
+
+void espi_setup_slave(struct fsl_espi_priv *priv)
+{
+	unsigned int max_hz;
+	sys_info_t sysinfo;
+	unsigned long spibrg = 0;
+	unsigned long spi_freq = 0;
+	unsigned char pm = 0;
+
+	max_hz = priv->speed_hz;
+
+	get_sys_info(&sysinfo);
+	spibrg = sysinfo.freq_systembus / 2;
+	priv->div16 = 0;
+	if ((spibrg / max_hz) > 32) {
+		priv->div16 = ESPI_CSMODE_DIV16;
+		pm = spibrg / (max_hz * 16 * 2);
+		if (pm > 16) {
+			pm = 16;
+			debug("max_hz is too low: %d Hz, %ld Hz is used.\n",
+			      max_hz, spibrg / (32 * 16));
+		}
+	} else {
+		pm = spibrg / (max_hz * 2);
+	}
+	if (pm)
+		pm--;
+	priv->pm = pm;
+
+	if (priv->div16)
+		spi_freq = spibrg / ((pm + 1) * 2 * 16);
+	else
+		spi_freq = spibrg / ((pm + 1) * 2);
+
+	/* set tx_timeout to 10 times of one espi FIFO entry go out */
+	priv->tx_timeout = DIV_ROUND_UP((US_PER_SECOND * ESPI_FIFO_WIDTH_BIT
+				* 10), spi_freq);/* Set eSPI BRG clock source */
+}
+
+#ifndef CONFIG_DM_SPI
 int spi_cs_is_valid(unsigned int bus, unsigned int cs)
 {
 	return bus == 0 && cs < ESPI_MAX_CS_NUM;
 }
 
-void spi_cs_activate(struct spi_slave *slave)
+struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
+				  unsigned int max_hz, unsigned int mode)
+{
+	struct fsl_spi_slave *fsl;
+
+	if (!spi_cs_is_valid(bus, cs))
+		return NULL;
+
+	fsl = spi_alloc_slave(struct fsl_spi_slave, bus, cs);
+	if (!fsl)
+		return NULL;
+
+	fsl->priv.espi = (void *)(CONFIG_SYS_MPC85xx_ESPI_ADDR);
+	fsl->priv.mode = mode;
+	fsl->priv.max_transfer_length = ESPI_MAX_DATA_TRANSFER_LEN;
+	fsl->priv.speed_hz = FSL_ESPI_DEFAULT_SCK_FREQ;
+
+	espi_setup_slave(&fsl->priv);
+
+	return &fsl->slave;
+}
+
+void spi_free_slave(struct spi_slave *slave)
 {
 	struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
-	ccsr_espi_t *espi = fsl->espi;
-	unsigned int com = 0;
-	size_t data_len = fsl->data_len;
 
-	com &= ~(ESPI_COM_CS(0x3) | ESPI_COM_TRANLEN(0xFFFF));
-	com |= ESPI_COM_CS(slave->cs);
-	com |= ESPI_COM_TRANLEN(data_len - 1);
-	out_be32(&espi->com, com);
+	free(fsl);
 }
 
-void spi_cs_deactivate(struct spi_slave *slave)
+int spi_claim_bus(struct spi_slave *slave)
 {
 	struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
-	ccsr_espi_t *espi = fsl->espi;
 
-	/* clear the RXCNT and TXCNT */
-	out_be32(&espi->mode, in_be32(&espi->mode) & (~ESPI_MODE_EN));
-	out_be32(&espi->mode, in_be32(&espi->mode) | ESPI_MODE_EN);
+	espi_claim_bus(&fsl->priv, slave->cs);
+
+	return 0;
+}
+
+void spi_release_bus(struct spi_slave *slave)
+{
+	/* Nothing to do */
+}
+
+int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
+	     void *din, unsigned long flags)
+{
+	struct fsl_spi_slave *espi = (struct fsl_spi_slave *)slave;
+
+	return espi_xfer(&espi->priv, slave->cs, bitlen, dout, din, flags);
+}
+#else
+static int fsl_espi_claim_bus(struct udevice *dev)
+{
+	struct udevice *bus = dev->parent;
+	struct dm_spi_slave_platdata *slave_plat =
+		 dev_get_parent_platdata(dev);
+
+	struct fsl_espi_priv  *priv =  dev_get_priv(bus);
+
+	espi_claim_bus(priv, slave_plat->cs);
+
+	return 0;
+}
+
+static int fsl_espi_release_bus(struct udevice *dev)
+{
+	/* Nothing to do */
+	return 0;
+}
+
+static int fsl_espi_xfer(struct udevice *dev, unsigned int bitlen,
+			 const void *dout, void *din, unsigned long flags)
+{
+	struct fsl_espi_priv  *priv;
+	struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev);
+	struct udevice *bus;
+
+	bus = dev->parent;
+	priv = dev_get_priv(bus);
+	return espi_xfer(priv, slave_plat->cs, bitlen, dout, din, flags);
+}
+
+static int fsl_espi_set_speed(struct udevice *bus, uint speed)
+{
+	/* Nothing to do */
+	return 0;
+}
+
+static int fsl_espi_set_mode(struct udevice *bus, uint mode)
+{
+	/* Nothing to do */
+	return 0;
 }
+
+static int fsl_espi_probe(struct udevice *bus)
+{
+	struct fsl_espi_platdata *plat = dev_get_platdata(bus);
+	struct fsl_espi_priv *priv = dev_get_priv(bus);
+
+	priv->espi = (ccsr_espi_t *)((u32)plat->regs_addr);
+	priv->max_transfer_length = ESPI_MAX_DATA_TRANSFER_LEN;
+	priv->speed_hz = plat->speed_hz;
+
+	espi_setup_slave(priv);
+
+	debug("%s probe done, bus-num %d.\n", bus->name, bus->seq);
+	return 0;
+}
+
+static int fsl_espi_child_pre_probe(struct udevice *dev)
+{
+	/* Nothing to do */
+	return 0;
+}
+
+static int fsl_espi_bind(struct udevice *bus)
+{
+	debug("%s assigned req_seq %d.\n", bus->name, bus->req_seq);
+	return 0;
+}
+
+static const struct dm_spi_ops fsl_espi_ops = {
+	.claim_bus	= fsl_espi_claim_bus,
+	.release_bus	= fsl_espi_release_bus,
+	.xfer		= fsl_espi_xfer,
+	.set_speed	= fsl_espi_set_speed,
+	.set_mode	= fsl_espi_set_mode,
+};
+
+#if !CONFIG_IS_ENABLED(OF_PLATDATA)
+static int fsl_espi_ofdata_to_platdata(struct udevice *bus)
+{
+	fdt_addr_t addr;
+	struct fsl_espi_platdata   *plat = bus->platdata;
+	const void *blob = gd->fdt_blob;
+	int node = dev_of_offset(bus);
+
+	addr = dev_read_addr(bus);
+	if (addr == FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	plat->regs_addr = lower_32_bits(addr);
+	plat->speed_hz = fdtdec_get_int(blob, node, "spi-max-frequency",
+					FSL_ESPI_DEFAULT_SCK_FREQ);
+
+	debug("ESPI: regs=%p, max-frequency=%d\n",
+	      &plat->regs_addr, plat->speed_hz);
+
+	return 0;
+}
+
+static const struct udevice_id fsl_espi_ids[] = {
+	{ .compatible = "fsl,mpc8536-espi" },
+	{ }
+};
+#endif
+
+U_BOOT_DRIVER(fsl_espi) = {
+	.name	= "fsl_espi",
+	.id	= UCLASS_SPI,
+#if !CONFIG_IS_ENABLED(OF_PLATDATA)
+	.of_match = fsl_espi_ids,
+	.ofdata_to_platdata = fsl_espi_ofdata_to_platdata,
+#endif
+	.ops	= &fsl_espi_ops,
+	.platdata_auto_alloc_size = sizeof(struct fsl_espi_platdata),
+	.priv_auto_alloc_size = sizeof(struct fsl_espi_priv),
+	.probe	= fsl_espi_probe,
+	.child_pre_probe = fsl_espi_child_pre_probe,
+	.bind = fsl_espi_bind,
+};
+#endif
Signature · 1 line
2.17.1
#2 lore raw

PATCH v2 2/5 dm: spi: Convert Freescale ESPI driver to driver model

Hi,

Quoted 32 lines · Chuanhua Han

Modify the Freescale ESPI driver to support the driver model. Also resolved the following problems:

===================== WARNING ====================== This board does not use CONFIG_DM_SPI. Please update the board before v2019.04 for no dm conversion
and v2019.07 for partially dm converted drivers. Failure to update can lead to driver/board removal See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ====================== This board does not use CONFIG_DM_SPI_FLASH. Please update the board to use CONFIG_SPI_FLASH before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info.
====================================================

---
Changes in v2:
- The fsl_espi driver support both OF_CONTROL and PLATDATA

 drivers/spi/fsl_espi.c | 454 +++++++++++++++++++++++++++++------------
 1 file changed, 320 insertions(+), 134 deletions(-)
drivers/spi/fsl_espi.c +0 -0
index 7444ae1a06..a2f4027fca 100644
@@ -4,17 +4,27 @@
  *

drivers/spi/fsl_espi.c line 13

Quoted 10 lines
drivers/spi/fsl_espi.c +1 -1
  * Copyright 2010-2011 Freescale Semiconductor, Inc.
  * Author: Mingkai Hu (Mingkai.hu at freescale.com)
+ *        Chuanhua Han (chuanhua.han at nxp.com)
  */
 
 #include <common.h>
-
 #include <malloc.h>
 #include <spi.h>
 #include <asm/immap_85xx.h>

Please sort the includes - this one should go at the end

Quoted 20 lines
drivers/spi/fsl_espi.c +12 -2
+#include <dm.h>
+#include <errno.h>
+#include <fdtdec.h>
+
+struct fsl_espi_platdata {
+       uint flags;
+       uint speed_hz;
+       uint num_chipselect;
+       fdt_addr_t regs_addr;
+};
 
-struct fsl_spi_slave {
-       struct spi_slave slave;
+struct fsl_espi_priv {
        ccsr_espi_t     *espi;
+       u32 speed_hz;
        unsigned int    div16;
        unsigned int    pm;
        int             tx_timeout;

drivers/spi/fsl_espi.c struct fsl_spi_slave { · line 44

Quoted 10 lines
drivers/spi/fsl_espi.c +6 -0
@@ -25,9 +35,18 @@ struct fsl_spi_slave {
        unsigned int    max_transfer_length;
 };
 
+struct fsl_spi_slave {
+       struct spi_slave slave;
+       struct fsl_espi_priv priv;
+};
+
 #define to_fsl_spi_slave(s) container_of(s, struct fsl_spi_slave, slave)
+#define to_fsl_spi_priv(p) container_of(p, struct fsl_spi_slave, priv)

We shouldn't really need this. Can we just pass the containing stuct instead?

Quoted 54 lines
drivers/spi/fsl_espi.c +3 -42
 #define US_PER_SECOND          1000000UL
 
+/* default SCK frequency, unit: HZ */
+#define FSL_ESPI_DEFAULT_SCK_FREQ   10000000
+
 #define ESPI_MAX_CS_NUM                4
 #define ESPI_FIFO_WIDTH_BIT    32
 
@@ -62,121 +81,46 @@ struct fsl_spi_slave {
 
 #define ESPI_MAX_DATA_TRANSFER_LEN 0xFFF0
 
-struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
-               unsigned int max_hz, unsigned int mode)
-{
-       struct fsl_spi_slave *fsl;
-       sys_info_t sysinfo;
-       unsigned long spibrg = 0;
-       unsigned long spi_freq = 0;
-       unsigned char pm = 0;
-
-       if (!spi_cs_is_valid(bus, cs))
-               return NULL;
-
-       fsl = spi_alloc_slave(struct fsl_spi_slave, bus, cs);
-       if (!fsl)
-               return NULL;
-
-       fsl->espi = (void *)(CONFIG_SYS_MPC85xx_ESPI_ADDR);
-       fsl->mode = mode;
-       fsl->max_transfer_length = ESPI_MAX_DATA_TRANSFER_LEN;
-
-       /* Set eSPI BRG clock source */
-       get_sys_info(&sysinfo);
-       spibrg = sysinfo.freq_systembus / 2;
-       fsl->div16 = 0;
-       if ((spibrg / max_hz) > 32) {
-               fsl->div16 = ESPI_CSMODE_DIV16;
-               pm = spibrg / (max_hz * 16 * 2);
-               if (pm > 16) {
-                       pm = 16;
-                       debug("Requested speed is too low: %d Hz, %ld Hz "
-                               "is used.\n", max_hz, spibrg / (32 * 16));
-               }
-       } else
-               pm = spibrg / (max_hz * 2);
-       if (pm)
-               pm--;
-       fsl->pm = pm;
-
-       if (fsl->div16)
-               spi_freq = spibrg / ((pm + 1) * 2 * 16);
-       else
-               spi_freq = spibrg / ((pm + 1) * 2);

drivers/spi/fsl_espi.c struct fsl_spi_slave { · line 84

Quoted 10 lines
drivers/spi/fsl_espi.c +1 -9
-
-       /* set tx_timeout to 10 times of one espi FIFO entry go out */
-       fsl->tx_timeout = DIV_ROUND_UP((US_PER_SECOND * ESPI_FIFO_WIDTH_BIT
-                               * 10), spi_freq);
-
-       return &fsl->slave;
-}
-
-void spi_free_slave(struct spi_slave *slave)
+#ifndef CONFIG_DM_SPI

It is more common to put #idef CONFIG_DM_SPI first with the old code last.

Quoted 67 lines
drivers/spi/fsl_espi.c +14 -48
+void spi_cs_activate(struct spi_slave *slave)
 {
        struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
-       free(fsl);
-}
+       ccsr_espi_t *espi = fsl->priv.espi;
+       unsigned int com = 0;
+       size_t data_len = fsl->priv.data_len;
 
-int spi_claim_bus(struct spi_slave *slave)
+       com &= ~(ESPI_COM_CS(0x3) | ESPI_COM_TRANLEN(0xFFFF));
+       com |= ESPI_COM_CS(slave->cs);
+       com |= ESPI_COM_TRANLEN(data_len - 1);
+       out_be32(&espi->com, com);
+}
+#else
+void fsl_spi_cs_activate(struct fsl_espi_priv *priv,  uint cs)
 {
-       struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
-       ccsr_espi_t *espi = fsl->espi;
-       unsigned char pm = fsl->pm;
-       unsigned int cs = slave->cs;
-       unsigned int mode =  fsl->mode;
-       unsigned int div16 = fsl->div16;
-       int i;
-
-       debug("%s: bus:%i cs:%i\n", __func__, slave->bus, cs);
-
-       /* Enable eSPI interface */
-       out_be32(&espi->mode, ESPI_MODE_RXTHR(3)
-                       | ESPI_MODE_TXTHR(4) | ESPI_MODE_EN);
-
-       out_be32(&espi->event, 0xffffffff); /* Clear all eSPI events */
-       out_be32(&espi->mask, 0x00000000); /* Mask  all eSPI interrupts */
-
-       /* Init CS mode interface */
-       for (i = 0; i < ESPI_MAX_CS_NUM; i++)
-               out_be32(&espi->csmode[i], ESPI_CSMODE_INIT_VAL);
-
-       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs]) &
-               ~(ESPI_CSMODE_PM(0xF) | ESPI_CSMODE_DIV16
-               | ESPI_CSMODE_CI_INACTIVEHIGH | ESPI_CSMODE_CP_BEGIN_EDGCLK
-               | ESPI_CSMODE_REV_MSB_FIRST | ESPI_CSMODE_LEN(0xF)));
-
-       /* Set eSPI BRG clock source */
-       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-               | ESPI_CSMODE_PM(pm) | div16);
-
-       /* Set eSPI mode */
-       if (mode & SPI_CPHA)
-               out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-                       | ESPI_CSMODE_CP_BEGIN_EDGCLK);
-       if (mode & SPI_CPOL)
-               out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-                       | ESPI_CSMODE_CI_INACTIVEHIGH);
-
-       /* Character bit order: msb first */
-       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-               | ESPI_CSMODE_REV_MSB_FIRST);
-
-       /* Character length in bits, between 0x3~0xf, i.e. 4bits~16bits */
-       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-               | ESPI_CSMODE_LEN(7));
+       ccsr_espi_t *espi = priv->espi;
+       unsigned int com = 0;
+       size_t data_len = priv->data_len;
 

drivers/spi/fsl_espi.c struct fsl_spi_slave { · line 111

Quoted 10 lines
drivers/spi/fsl_espi.c +6 -2
-       return 0;
+       com &= ~(ESPI_COM_CS(0x3) | ESPI_COM_TRANLEN(0xFFFF));
+       com |= ESPI_COM_CS(cs);
+       com |= ESPI_COM_TRANLEN(data_len - 1);
+       out_be32(&espi->com, com);
 }
+#endif
 
-void spi_release_bus(struct spi_slave *slave)
+void spi_cs_deactivate(struct spi_slave *slave)

Should this be static?

Regards,
Simon

#3 lore raw

[U-Boot] [EXT] Re: [PATCH v2 2/5] dm: spi: Convert Freescale ESPI driver to driver model

Hi,

Quoted 248 lines

-----Original Message-----
From: Simon Glass <[email protected]>
Sent: 2019年6月23日 3:10
To: Chuanhua Han <[email protected]>
Cc: Jagan Teki <[email protected]>; Wolfgang Denk <[email protected]>; Shengzhou Liu <[email protected]>; Ruchika Gupta <[email protected]>; U-Boot Mailing List <[email protected]>; Prabhakar Kushwaha <[email protected]>; Jiafei Pan <[email protected]>; Yinbo Zhu <[email protected]>; Bin Meng <[email protected]>; Jagdish Gediya <[email protected]>
Subject: [EXT] Re: [PATCH v2 2/5] dm: spi: Convert Freescale ESPI driver to driver model

Caution: EXT Email

Hi,

Quoted 5 lines · Chuanhua Han

Modify the Freescale ESPI driver to support the driver model. Also resolved the following problems:

===================== WARNING ====================== This board

does

Quoted 6 lines

not use CONFIG_DM_SPI. Please update the board before v2019.04 for no dm conversion and v2019.07 for partially dm converted drivers. Failure to update can lead to driver/board removal See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ====================== This board

does

Quoted 21 lines

not use CONFIG_DM_SPI_FLASH. Please update the board to use CONFIG_SPI_FLASH before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info.
====================================================

---
Changes in v2:
- The fsl_espi driver support both OF_CONTROL and PLATDATA

 drivers/spi/fsl_espi.c | 454
+++++++++++++++++++++++++++++------------
 1 file changed, 320 insertions(+), 134 deletions(-)
drivers/spi/fsl_espi.c index renamed from drivers/spi/fsl_espi.c +0 -0

7444ae1a06..a2f4027fca 100644

drivers/spi/fsl_espi.c +0 -0
@@ -4,17 +4,27 @@
  *

drivers/spi/fsl_espi.c line 13

Quoted 10 lines
drivers/spi/fsl_espi.c +1 -1
  * Copyright 2010-2011 Freescale Semiconductor, Inc.
  * Author: Mingkai Hu (Mingkai.hu at freescale.com)
+ *        Chuanhua Han (chuanhua.han at nxp.com)
  */
 
 #include <common.h>
-
 #include <malloc.h>
 #include <spi.h>
 #include <asm/immap_85xx.h>

Please sort the includes - this one should go at the end

Quoted 22 lines
drivers/spi/fsl_espi.c +12 -2
+#include <dm.h>
+#include <errno.h>
+#include <fdtdec.h>
+
+struct fsl_espi_platdata {
+       uint flags;
+       uint speed_hz;
+       uint num_chipselect;
+       fdt_addr_t regs_addr;
+};
 
-struct fsl_spi_slave {
-       struct spi_slave slave;
+struct fsl_espi_priv {
        ccsr_espi_t     *espi;
+       u32 speed_hz;
        unsigned int    div16;
        unsigned int    pm;
        int             tx_timeout;
@@ -25,9 +35,18 @@ struct fsl_spi_slave {
        unsigned int    max_transfer_length;
 };

drivers/spi/fsl_espi.c struct fsl_spi_slave { · line 46

Quoted 10 lines
drivers/spi/fsl_espi.c +7 -0
 
+struct fsl_spi_slave {
+       struct spi_slave slave;
+       struct fsl_espi_priv priv;
+};
+
 #define to_fsl_spi_slave(s) container_of(s, struct fsl_spi_slave,
 slave)
+#define to_fsl_spi_priv(p) container_of(p, struct fsl_spi_slave,
+priv)

We shouldn't really need this. Can we just pass the containing stuct instead?

Quoted 32 lines
drivers/spi/fsl_espi.c +3 -20
 #define US_PER_SECOND          1000000UL
 
+/* default SCK frequency, unit: HZ */
+#define FSL_ESPI_DEFAULT_SCK_FREQ   10000000
+
 #define ESPI_MAX_CS_NUM                4
 #define ESPI_FIFO_WIDTH_BIT    32
@@ -62,121 +81,46 @@ struct fsl_spi_slave {
 
 #define ESPI_MAX_DATA_TRANSFER_LEN 0xFFF0
 
-struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
-               unsigned int max_hz, unsigned int mode)
-{
-       struct fsl_spi_slave *fsl;
-       sys_info_t sysinfo;
-       unsigned long spibrg = 0;
-       unsigned long spi_freq = 0;
-       unsigned char pm = 0;
-
-       if (!spi_cs_is_valid(bus, cs))
-               return NULL;
-
-       fsl = spi_alloc_slave(struct fsl_spi_slave, bus, cs);
-       if (!fsl)
-               return NULL;
-
-       fsl->espi = (void *)(CONFIG_SYS_MPC85xx_ESPI_ADDR);
-       fsl->mode = mode;
-       fsl->max_transfer_length = ESPI_MAX_DATA_TRANSFER_LEN;
-

drivers/spi/fsl_espi.c struct fsl_spi_slave { · line 94

Quoted 10 lines
drivers/spi/fsl_espi.c +0 -10
-       /* Set eSPI BRG clock source */
-       get_sys_info(&sysinfo);
-       spibrg = sysinfo.freq_systembus / 2;
-       fsl->div16 = 0;
-       if ((spibrg / max_hz) > 32) {
-               fsl->div16 = ESPI_CSMODE_DIV16;
-               pm = spibrg / (max_hz * 16 * 2);
-               if (pm > 16) {
-                       pm = 16;
-                       debug("Requested speed is too low: %d Hz, %ld

Hz "

Quoted 5 lines
drivers/spi/fsl_espi.c +0 -5
-                               "is used.\n", max_hz, spibrg / (32 * 16));
-               }
-       } else
-               pm = spibrg / (max_hz * 2);
-       if (pm)

drivers/spi/fsl_espi.c struct fsl_spi_slave {

Quoted 10 lines
drivers/spi/fsl_espi.c +0 -10
-               pm--;
-       fsl->pm = pm;
-
-       if (fsl->div16)
-               spi_freq = spibrg / ((pm + 1) * 2 * 16);
-       else
-               spi_freq = spibrg / ((pm + 1) * 2);
-
-       /* set tx_timeout to 10 times of one espi FIFO entry go out */
-       fsl->tx_timeout = DIV_ROUND_UP((US_PER_SECOND *

ESPI_FIFO_WIDTH_BIT

drivers/spi/fsl_espi.c struct fsl_spi_slave { · line 84

Quoted 7 lines
drivers/spi/fsl_espi.c +1 -6
-                               * 10), spi_freq);
-
-       return &fsl->slave;
-}
-
-void spi_free_slave(struct spi_slave *slave)
+#ifndef CONFIG_DM_SPI

It is more common to put #idef CONFIG_DM_SPI first with the old code last.

Quoted 24 lines
drivers/spi/fsl_espi.c +11 -9
+void spi_cs_activate(struct spi_slave *slave)
 {
        struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
-       free(fsl);
-}
+       ccsr_espi_t *espi = fsl->priv.espi;
+       unsigned int com = 0;
+       size_t data_len = fsl->priv.data_len;
 
-int spi_claim_bus(struct spi_slave *slave)
+       com &= ~(ESPI_COM_CS(0x3) | ESPI_COM_TRANLEN(0xFFFF));
+       com |= ESPI_COM_CS(slave->cs);
+       com |= ESPI_COM_TRANLEN(data_len - 1);
+       out_be32(&espi->com, com);
+}
+#else
+void fsl_spi_cs_activate(struct fsl_espi_priv *priv,  uint cs)
 {
-       struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
-       ccsr_espi_t *espi = fsl->espi;
-       unsigned char pm = fsl->pm;
-       unsigned int cs = slave->cs;
-       unsigned int mode =  fsl->mode;
-       unsigned int div16 = fsl->div16;

drivers/spi/fsl_espi.c struct fsl_spi_slave {

Quoted 10 lines
drivers/spi/fsl_espi.c +0 -10
-       int i;
-
-       debug("%s: bus:%i cs:%i\n", __func__, slave->bus, cs);
-
-       /* Enable eSPI interface */
-       out_be32(&espi->mode, ESPI_MODE_RXTHR(3)
-                       | ESPI_MODE_TXTHR(4) | ESPI_MODE_EN);
-
-       out_be32(&espi->event, 0xffffffff); /* Clear all eSPI events */
-       out_be32(&espi->mask, 0x00000000); /* Mask  all eSPI interrupts

*/

drivers/spi/fsl_espi.c struct fsl_spi_slave {

Quoted 8 lines
drivers/spi/fsl_espi.c +0 -8
-
-       /* Init CS mode interface */
-       for (i = 0; i < ESPI_MAX_CS_NUM; i++)
-               out_be32(&espi->csmode[i], ESPI_CSMODE_INIT_VAL);
-
-       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs]) &
-               ~(ESPI_CSMODE_PM(0xF) | ESPI_CSMODE_DIV16
-               | ESPI_CSMODE_CI_INACTIVEHIGH |

ESPI_CSMODE_CP_BEGIN_EDGCLK

drivers/spi/fsl_espi.c struct fsl_spi_slave { · line 147

Quoted 1 line
drivers/spi/fsl_espi.c +0 -1
-               | ESPI_CSMODE_REV_MSB_FIRST |

ESPI_CSMODE_LEN(0xF)));

Quoted 32 lines
drivers/spi/fsl_espi.c +8 -21
-
-       /* Set eSPI BRG clock source */
-       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-               | ESPI_CSMODE_PM(pm) | div16);
-
-       /* Set eSPI mode */
-       if (mode & SPI_CPHA)
-               out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-                       | ESPI_CSMODE_CP_BEGIN_EDGCLK);
-       if (mode & SPI_CPOL)
-               out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-                       | ESPI_CSMODE_CI_INACTIVEHIGH);
-
-       /* Character bit order: msb first */
-       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-               | ESPI_CSMODE_REV_MSB_FIRST);
-
-       /* Character length in bits, between 0x3~0xf, i.e. 4bits~16bits */
-       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-               | ESPI_CSMODE_LEN(7));
+       ccsr_espi_t *espi = priv->espi;
+       unsigned int com = 0;
+       size_t data_len = priv->data_len;
 
-       return 0;
+       com &= ~(ESPI_COM_CS(0x3) | ESPI_COM_TRANLEN(0xFFFF));
+       com |= ESPI_COM_CS(cs);
+       com |= ESPI_COM_TRANLEN(data_len - 1);
+       out_be32(&espi->com, com);
 }
+#endif
 
Quoted 5 lines

drivers/spi/fsl_espi.c struct fsl_spi_slave { · line 111

Quoted 2 lines
drivers/spi/fsl_espi.c +1 -1
-void spi_release_bus(struct spi_slave *slave)
+void spi_cs_deactivate(struct spi_slave *slave)

Should this be static?

I have sent the fourth edition you see the new patchwork:

https://patchwork.ozlabs.org/project/uboot/list/?series=115242

Quoted 2 lines

Regards,
Simon

#4 lore raw

[U-Boot] [EXT] Re: [PATCH v2 2/5] dm: spi: Convert Freescale ESPI driver to driver model

In reply to Simon Glass
Quoted 60 lines

-----Original Message-----
From: Simon Glass <[email protected]>
Sent: 2019年6月23日 3:10
To: Chuanhua Han <[email protected]>
Cc: Jagan Teki <[email protected]>; Wolfgang Denk <[email protected]>; Shengzhou Liu <[email protected]>; Ruchika Gupta <[email protected]>; U-Boot Mailing List <[email protected]>; Prabhakar Kushwaha <[email protected]>; Jiafei Pan <[email protected]>; Yinbo Zhu <[email protected]>; Bin Meng <[email protected]>; Jagdish Gediya <[email protected]>
Subject: [EXT] Re: [PATCH v2 2/5] dm: spi: Convert Freescale ESPI driver to driver model

Caution: EXT Email

Hi,

Quoted 5 lines · Chuanhua Han

Modify the Freescale ESPI driver to support the driver model. Also resolved the following problems:

===================== WARNING ====================== This board

does

Quoted 6 lines

not use CONFIG_DM_SPI. Please update the board before v2019.04 for no dm conversion and v2019.07 for partially dm converted drivers. Failure to update can lead to driver/board removal See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ====================== This board

does

Quoted 26 lines

not use CONFIG_DM_SPI_FLASH. Please update the board to use CONFIG_SPI_FLASH before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info.
====================================================

---
Changes in v2:
- The fsl_espi driver support both OF_CONTROL and PLATDATA

 drivers/spi/fsl_espi.c | 454
+++++++++++++++++++++++++++++------------
 1 file changed, 320 insertions(+), 134 deletions(-)
drivers/spi/fsl_espi.c index renamed from drivers/spi/fsl_espi.c +0 -0

7444ae1a06..a2f4027fca 100644

drivers/spi/fsl_espi.c +1 -0
@@ -4,17 +4,27 @@
  *
  * Copyright 2010-2011 Freescale Semiconductor, Inc.
  * Author: Mingkai Hu (Mingkai.hu at freescale.com)
+ *        Chuanhua Han (chuanhua.han at nxp.com)
  */
 
Quoted 7 lines

drivers/spi/fsl_espi.c line 13

Quoted 5 lines
drivers/spi/fsl_espi.c +0 -1
 #include <common.h>
-
 #include <malloc.h>
 #include <spi.h>
 #include <asm/immap_85xx.h>

Please sort the includes - this one should go at the end

The header file is also in this position before I modify this file. Is this necessary?

Quoted 24 lines
Quoted 24 lines
drivers/spi/fsl_espi.c +12 -2
+#include <dm.h>
+#include <errno.h>
+#include <fdtdec.h>
+
+struct fsl_espi_platdata {
+       uint flags;
+       uint speed_hz;
+       uint num_chipselect;
+       fdt_addr_t regs_addr;
+};
 
-struct fsl_spi_slave {
-       struct spi_slave slave;
+struct fsl_espi_priv {
        ccsr_espi_t     *espi;
+       u32 speed_hz;
        unsigned int    div16;
        unsigned int    pm;
        int             tx_timeout;
@@ -25,9 +35,18 @@ struct fsl_spi_slave {
        unsigned int    max_transfer_length;
 };
 
Quoted 11 lines

drivers/spi/fsl_espi.c struct fsl_spi_slave {

Quoted 9 lines
drivers/spi/fsl_espi.c +7 -0
+struct fsl_spi_slave {
+       struct spi_slave slave;
+       struct fsl_espi_priv priv;
+};
+
 #define to_fsl_spi_slave(s) container_of(s, struct fsl_spi_slave,
 slave)
+#define to_fsl_spi_priv(p) container_of(p, struct fsl_spi_slave,
+priv)

We shouldn't really need this. Can we just pass the containing stuct instead?

This has been removed in the new version of the patch.

Quoted 60 lines
Quoted 33 lines
drivers/spi/fsl_espi.c +3 -20
 #define US_PER_SECOND          1000000UL
 
+/* default SCK frequency, unit: HZ */
+#define FSL_ESPI_DEFAULT_SCK_FREQ   10000000
+
 #define ESPI_MAX_CS_NUM                4
 #define ESPI_FIFO_WIDTH_BIT    32
@@ -62,121 +81,46 @@ struct fsl_spi_slave {
 
 #define ESPI_MAX_DATA_TRANSFER_LEN 0xFFF0
 
-struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
-               unsigned int max_hz, unsigned int mode)
-{
-       struct fsl_spi_slave *fsl;
-       sys_info_t sysinfo;
-       unsigned long spibrg = 0;
-       unsigned long spi_freq = 0;
-       unsigned char pm = 0;
-
-       if (!spi_cs_is_valid(bus, cs))
-               return NULL;
-
-       fsl = spi_alloc_slave(struct fsl_spi_slave, bus, cs);
-       if (!fsl)
-               return NULL;
-
-       fsl->espi = (void *)(CONFIG_SYS_MPC85xx_ESPI_ADDR);
-       fsl->mode = mode;
-       fsl->max_transfer_length = ESPI_MAX_DATA_TRANSFER_LEN;
-

drivers/spi/fsl_espi.c struct fsl_spi_slave { · line 94

Quoted 10 lines
drivers/spi/fsl_espi.c +0 -10
-       /* Set eSPI BRG clock source */
-       get_sys_info(&sysinfo);
-       spibrg = sysinfo.freq_systembus / 2;
-       fsl->div16 = 0;
-       if ((spibrg / max_hz) > 32) {
-               fsl->div16 = ESPI_CSMODE_DIV16;
-               pm = spibrg / (max_hz * 16 * 2);
-               if (pm > 16) {
-                       pm = 16;
-                       debug("Requested speed is too low: %d Hz, %ld

Hz "

Quoted 5 lines
drivers/spi/fsl_espi.c +0 -5
-                               "is used.\n", max_hz, spibrg / (32 * 16));
-               }
-       } else
-               pm = spibrg / (max_hz * 2);
-       if (pm)

drivers/spi/fsl_espi.c struct fsl_spi_slave {

Quoted 10 lines
drivers/spi/fsl_espi.c +0 -10
-               pm--;
-       fsl->pm = pm;
-
-       if (fsl->div16)
-               spi_freq = spibrg / ((pm + 1) * 2 * 16);
-       else
-               spi_freq = spibrg / ((pm + 1) * 2);
-
-       /* set tx_timeout to 10 times of one espi FIFO entry go out */
-       fsl->tx_timeout = DIV_ROUND_UP((US_PER_SECOND *

ESPI_FIFO_WIDTH_BIT

Quoted 9 lines

drivers/spi/fsl_espi.c struct fsl_spi_slave { · line 84

Quoted 7 lines
drivers/spi/fsl_espi.c +1 -6
-                               * 10), spi_freq);
-
-       return &fsl->slave;
-}
-
-void spi_free_slave(struct spi_slave *slave)
+#ifndef CONFIG_DM_SPI

It is more common to put #idef CONFIG_DM_SPI first with the old code last.

I have checked many files using #ifndef CONFIG_DM_SPI to separate DM code and non-dm code.

Quoted 79 lines
Quoted 25 lines
drivers/spi/fsl_espi.c +11 -9
+void spi_cs_activate(struct spi_slave *slave)
 {
        struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
-       free(fsl);
-}
+       ccsr_espi_t *espi = fsl->priv.espi;
+       unsigned int com = 0;
+       size_t data_len = fsl->priv.data_len;
 
-int spi_claim_bus(struct spi_slave *slave)
+       com &= ~(ESPI_COM_CS(0x3) | ESPI_COM_TRANLEN(0xFFFF));
+       com |= ESPI_COM_CS(slave->cs);
+       com |= ESPI_COM_TRANLEN(data_len - 1);
+       out_be32(&espi->com, com);
+}
+#else
+void fsl_spi_cs_activate(struct fsl_espi_priv *priv,  uint cs)
 {
-       struct fsl_spi_slave *fsl = to_fsl_spi_slave(slave);
-       ccsr_espi_t *espi = fsl->espi;
-       unsigned char pm = fsl->pm;
-       unsigned int cs = slave->cs;
-       unsigned int mode =  fsl->mode;
-       unsigned int div16 = fsl->div16;

drivers/spi/fsl_espi.c struct fsl_spi_slave {

Quoted 10 lines
drivers/spi/fsl_espi.c +0 -10
-       int i;
-
-       debug("%s: bus:%i cs:%i\n", __func__, slave->bus, cs);
-
-       /* Enable eSPI interface */
-       out_be32(&espi->mode, ESPI_MODE_RXTHR(3)
-                       | ESPI_MODE_TXTHR(4) | ESPI_MODE_EN);
-
-       out_be32(&espi->event, 0xffffffff); /* Clear all eSPI events */
-       out_be32(&espi->mask, 0x00000000); /* Mask  all eSPI interrupts

*/

drivers/spi/fsl_espi.c struct fsl_spi_slave {

Quoted 8 lines
drivers/spi/fsl_espi.c +0 -8
-
-       /* Init CS mode interface */
-       for (i = 0; i < ESPI_MAX_CS_NUM; i++)
-               out_be32(&espi->csmode[i], ESPI_CSMODE_INIT_VAL);
-
-       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs]) &
-               ~(ESPI_CSMODE_PM(0xF) | ESPI_CSMODE_DIV16
-               | ESPI_CSMODE_CI_INACTIVEHIGH |

ESPI_CSMODE_CP_BEGIN_EDGCLK

drivers/spi/fsl_espi.c struct fsl_spi_slave { · line 147

Quoted 1 line
drivers/spi/fsl_espi.c +0 -1
-               | ESPI_CSMODE_REV_MSB_FIRST |

ESPI_CSMODE_LEN(0xF)));

Quoted 32 lines
drivers/spi/fsl_espi.c +8 -21
-
-       /* Set eSPI BRG clock source */
-       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-               | ESPI_CSMODE_PM(pm) | div16);
-
-       /* Set eSPI mode */
-       if (mode & SPI_CPHA)
-               out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-                       | ESPI_CSMODE_CP_BEGIN_EDGCLK);
-       if (mode & SPI_CPOL)
-               out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-                       | ESPI_CSMODE_CI_INACTIVEHIGH);
-
-       /* Character bit order: msb first */
-       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-               | ESPI_CSMODE_REV_MSB_FIRST);
-
-       /* Character length in bits, between 0x3~0xf, i.e. 4bits~16bits */
-       out_be32(&espi->csmode[cs], in_be32(&espi->csmode[cs])
-               | ESPI_CSMODE_LEN(7));
+       ccsr_espi_t *espi = priv->espi;
+       unsigned int com = 0;
+       size_t data_len = priv->data_len;
 
-       return 0;
+       com &= ~(ESPI_COM_CS(0x3) | ESPI_COM_TRANLEN(0xFFFF));
+       com |= ESPI_COM_CS(cs);
+       com |= ESPI_COM_TRANLEN(data_len - 1);
+       out_be32(&espi->com, com);
 }
+#endif
 
Quoted 4 lines

drivers/spi/fsl_espi.c struct fsl_spi_slave { · line 111

Quoted 2 lines
drivers/spi/fsl_espi.c +1 -1
-void spi_release_bus(struct spi_slave *slave)
+void spi_cs_deactivate(struct spi_slave *slave)

Should this be static?

This function may be called by the code of other files, so this function should not need to use static to limit it.

Quoted 3 lines

Regards,
Simon

#5 lore raw

PATCH v2 3/5 powerpc: dts: t2080: add espi controller node support

In reply to Chuanhua Han

Add espi controller node to support t2080.

---
depends on:
- https://patchwork.ozlabs.org/project/uboot/list/?series=99439

Changes in v2:
- No change.

 arch/powerpc/dts/t2080.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)
arch/powerpc/dts/t2080.dtsi +10 -0
index d2bebb08b6..e3970d3590 100644
@@ -69,6 +69,16 @@
 			voltage-ranges = <1800 1800 3300 3300>;
 		};
 
+		espi0: spi at 110000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,mpc8536-espi";
+			reg = <0x110000 0x1000>;
+			interrupts = <53 0x2 0 0>;
+			fsl,espi-num-chipselects = <4>;
+			status = "disabled";
+		};
+
 		usb0: usb at 210000 {
 			compatible = "fsl-usb2-mph";
 			reg = <0x210000 0x1000>;
Signature · 1 line
2.17.1
#6 lore raw

PATCH v2 4/5 powerpc: dts: t2080qds: add espi slave nodes support

In reply to Chuanhua Han

Add espi slave nodes to support t2080qds.

---
depends on:
- https://patchwork.ozlabs.org/project/uboot/list/?series=99439

Changes in v2:
- No change.

 arch/powerpc/dts/t2080qds.dts | 33 +++++++++++++++++++++++++++++++++
 1 file changed, 33 insertions(+)
arch/powerpc/dts/t2080qds.dts +33 -0
index 1819a081dd..5eebe26010 100644
@@ -14,4 +14,37 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 	interrupt-parent = <&mpic>;
+
+	aliases {
+		spi0 = &espi0;
+	};
+};
+
+&espi0 {
+
+	status = "okay";
+	flash at 0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "micron,n25q128a11", "jedec,spi-nor"; /* 16MB */
+		reg = <0>;
+		spi-max-frequency = <40000000>; /* input clock */
+	};
+
+	flash at 1 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "sst,sst25wf040", "jedec,spi-nor";
+		reg = <1>;
+		spi-max-frequency = <35000000>;
+	};
+
+	flash at 2 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "eon,en25s64", "jedec,spi-nor";
+		reg = <2>;
+		spi-max-frequency = <35000000>;
+	};
+
 };
Signature · 1 line
2.17.1
#7 lore raw

PATCH v2 5/5 configs: enable espi device module in T2080QDS

In reply to Chuanhua Han

This patch is to enable espi DM for T2080QDS in uboot

---
depends on:
- https://patchwork.ozlabs.org/project/uboot/list/?series=99439

Changes in v2:
- No change.

 configs/T2080QDS_NAND_defconfig           | 2 ++
 configs/T2080QDS_SDCARD_defconfig         | 2 ++
 configs/T2080QDS_SECURE_BOOT_defconfig    | 2 ++
 configs/T2080QDS_SPIFLASH_defconfig       | 2 ++
 configs/T2080QDS_SRIO_PCIE_BOOT_defconfig | 2 ++
 configs/T2080QDS_defconfig                | 2 ++
 6 files changed, 12 insertions(+)
configs/T2080QDS_NAND_defconfig +2 -0
index 72a6e8772b..1f8ae64294 100644
@@ -66,3 +66,5 @@ CONFIG_FSL_ESPI=y
 CONFIG_USB=y
 CONFIG_DM_USB=y
 CONFIG_USB_STORAGE=y
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
configs/T2080QDS_SDCARD_defconfig +2 -0
index 2e3a51aa0a..668a92b49c 100644
@@ -65,3 +65,5 @@ CONFIG_FSL_ESPI=y
 CONFIG_USB=y
 CONFIG_DM_USB=y
 CONFIG_USB_STORAGE=y
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
configs/T2080QDS_SECURE_BOOT_defconfig +2 -0
index 6cb36ebbb3..8e317d8e4e 100644
@@ -58,3 +58,5 @@ CONFIG_USB_STORAGE=y
 CONFIG_RSA=y
 CONFIG_SPL_RSA=y
 CONFIG_RSA_SOFTWARE_EXP=y
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
configs/T2080QDS_SPIFLASH_defconfig +2 -0
index 9d17a99198..5da8c3a060 100644
@@ -66,3 +66,5 @@ CONFIG_FSL_ESPI=y
 CONFIG_USB=y
 CONFIG_DM_USB=y
 CONFIG_USB_STORAGE=y
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
configs/T2080QDS_SRIO_PCIE_BOOT_defconfig +2 -0
index 560ae143a1..2fa6ccc8d1 100644
@@ -48,3 +48,5 @@ CONFIG_FSL_ESPI=y
 CONFIG_USB=y
 CONFIG_DM_USB=y
 CONFIG_USB_STORAGE=y
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
configs/T2080QDS_defconfig +2 -0
index 4d6314b1cf..8c5735aede 100644
@@ -55,3 +55,5 @@ CONFIG_FSL_ESPI=y
 CONFIG_USB=y
 CONFIG_DM_USB=y
 CONFIG_USB_STORAGE=y
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
Signature · 1 line
2.17.1
#8 lore raw

PATCH v2 1/5 spl: dm: disable SPI DM flash for non-DM SPL

In reply to Chuanhua Han
Quoted 17 lines · Chuanhua Han

This patch solves the problem that spiboot cannot be performed in non-DM SPL.

---
Changes in v2:
- No change.

 include/config_uncmd_spl.h | 1 +
 1 file changed, 1 insertion(+)
include/config_uncmd_spl.h +0 -0
index c2f9735ce7..da94b3d9df 100644

include/config_uncmd_spl.h line 21

Quoted 7 lines
include/config_uncmd_spl.h +1 -0
@@ -15,6 +15,7 @@
 #undef CONFIG_DM_GPIO
 #undef CONFIG_DM_I2C
 #undef CONFIG_DM_SPI
+#undef CONFIG_DM_SPI_FLASH
 #endif
 
 #undef CONFIG_DM_WARN

Long term, this shows places where we need CONFIG_SPL_DM_xxx and code should be using CONFIG_IS_ENABLED(DM_xxx). Please update at least the DM_SPI_FLASH case you're finding to behave like that, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190524/ba14ed1a/attachment.sig>
#9 lore raw
Quoted 38 lines

-----Original Message-----
From: Tom Rini <[email protected]>
Sent: 2019年5月24日 22:24
To: Chuanhua Han <[email protected]>
Cc: jagan at openedev.com; wd at denx.de; Shengzhou Liu <[email protected]>; Ruchika Gupta <[email protected]>; Pan Jiafei <[email protected]>; u-boot at lists.denx.de; Jiafei Pan <[email protected]>; Yinbo Zhu <[email protected]>
Subject: [EXT] Re: [U-Boot] [PATCH v2 1/5] spl: dm: disable SPI DM flash for non-DM SPL

Quoted 23 lines · Chuanhua Han

This patch solves the problem that spiboot cannot be performed in non-DM SPL.

---
Changes in v2:
- No change.

 include/config_uncmd_spl.h | 1 +
 1 file changed, 1 insertion(+)
include/config_uncmd_spl.h +1 -0
index c2f9735ce7..da94b3d9df 100644
@@ -15,6 +15,7 @@
 #undef CONFIG_DM_GPIO
 #undef CONFIG_DM_I2C
 #undef CONFIG_DM_SPI
+#undef CONFIG_DM_SPI_FLASH
 #endif
 
Quoted 5 lines

include/config_uncmd_spl.h line 21

Quoted 1 line
include/config_uncmd_spl.h +0 -0
 #undef CONFIG_DM_WARN

Long term, this shows places where we need CONFIG_SPL_DM_xxx and code should be using CONFIG_IS_ENABLED(DM_xxx). Please update at least the DM_SPI_FLASH case you're finding to behave like that, thanks!

I don't understand you very much. Are you saying to modify the spi-flash related code?

Quoted 3 lines

--
Tom

#10 lore raw
Quoted 38 lines · Chuanhua Han
Quoted 38 lines

-----Original Message-----
From: Tom Rini <[email protected]>
Sent: 2019年5月24日 22:24
To: Chuanhua Han <[email protected]>
Cc: jagan at openedev.com; wd at denx.de; Shengzhou Liu <[email protected]>; Ruchika Gupta <[email protected]>; Pan Jiafei <[email protected]>; u-boot at lists.denx.de; Jiafei Pan <[email protected]>; Yinbo Zhu <[email protected]>
Subject: [EXT] Re: [U-Boot] [PATCH v2 1/5] spl: dm: disable SPI DM flash for non-DM SPL

Quoted 23 lines · Chuanhua Han

This patch solves the problem that spiboot cannot be performed in non-DM SPL.

---
Changes in v2:
- No change.

 include/config_uncmd_spl.h | 1 +
 1 file changed, 1 insertion(+)
include/config_uncmd_spl.h +1 -0
index c2f9735ce7..da94b3d9df 100644
@@ -15,6 +15,7 @@
 #undef CONFIG_DM_GPIO
 #undef CONFIG_DM_I2C
 #undef CONFIG_DM_SPI
+#undef CONFIG_DM_SPI_FLASH
 #endif
 
Quoted 6 lines
Quoted 5 lines

include/config_uncmd_spl.h line 21

Quoted 1 line
include/config_uncmd_spl.h +0 -0
 #undef CONFIG_DM_WARN

Long term, this shows places where we need CONFIG_SPL_DM_xxx and code should be using CONFIG_IS_ENABLED(DM_xxx). Please update at least the DM_SPI_FLASH case you're finding to behave like that, thanks!

I don't understand you very much. Are you saying to modify the spi-flash related code?

Correct. include/config_uncmd_spl.h should be removed as there should, long term, be no cases of code in SPL that we can / should exclude not guarded by CONFIG_SPL_xxx instead.

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190530/ac1534db/attachment.sig>
#11 lore raw
Quoted 57 lines

-----Original Message-----
From: Tom Rini <[email protected]>
Sent: 2019年5月31日 3:43
To: Chuanhua Han <[email protected]>
Cc: jagan at openedev.com; wd at denx.de; Shengzhou Liu <[email protected]>; Ruchika Gupta <[email protected]>; Pan Jiafei <[email protected]>; u-boot at lists.denx.de; Jiafei Pan <[email protected]>; Yinbo Zhu <[email protected]>
Subject: Re: [EXT] Re: [U-Boot] [PATCH v2 1/5] spl: dm: disable SPI DM flash for non-DM SPL

Quoted 43 lines · Chuanhua Han
Quoted 43 lines

-----Original Message-----
From: Tom Rini <[email protected]>
Sent: 2019年5月24日 22:24
To: Chuanhua Han <[email protected]>
Cc: jagan at openedev.com; wd at denx.de; Shengzhou Liu <[email protected]>; Ruchika Gupta <[email protected]>; Pan Jiafei <[email protected]>; u-boot at lists.denx.de; Jiafei Pan <[email protected]>; Yinbo Zhu <[email protected]>
Subject: [EXT] Re: [U-Boot] [PATCH v2 1/5] spl: dm: disable SPI DM flash for non-DM SPL

Quoted 17 lines · Chuanhua Han

This patch solves the problem that spiboot cannot be performed in non-DM SPL.

---
Changes in v2:
- No change.

 include/config_uncmd_spl.h | 1 +
 1 file changed, 1 insertion(+)
(quoted diff) +0 -0

b/include/config_uncmd_spl.h index c2f9735ce7..da94b3d9df 100644

include/config_uncmd_spl.h line 21

Quoted 7 lines
include/config_uncmd_spl.h +1 -0
@@ -15,6 +15,7 @@
 #undef CONFIG_DM_GPIO
 #undef CONFIG_DM_I2C
 #undef CONFIG_DM_SPI
+#undef CONFIG_DM_SPI_FLASH
 #endif
 
 #undef CONFIG_DM_WARN

Long term, this shows places where we need CONFIG_SPL_DM_xxx and code should be using CONFIG_IS_ENABLED(DM_xxx). Please update at least the DM_SPI_FLASH case you're finding to behave like that, thanks!

Quoted 6 lines
Quoted 1 line

I don't understand you very much. Are you saying to modify the spi-flash

related code?

Correct. include/config_uncmd_spl.h should be removed as there should, long term, be no cases of code in SPL that we can / should exclude not guarded by CONFIG_SPL_xxx instead.

Do you mean I should not add "#undef CONFIG_DM_SPI_FLASH" in include/config_uncmd_spl.h? What should I do? Is there any code or file for reference?

Quoted 3 lines

--
Tom

#12 lore raw
Quoted 57 lines · Chuanhua Han
Quoted 57 lines

-----Original Message-----
From: Tom Rini <[email protected]>
Sent: 2019年5月31日 3:43
To: Chuanhua Han <[email protected]>
Cc: jagan at openedev.com; wd at denx.de; Shengzhou Liu <[email protected]>; Ruchika Gupta <[email protected]>; Pan Jiafei <[email protected]>; u-boot at lists.denx.de; Jiafei Pan <[email protected]>; Yinbo Zhu <[email protected]>
Subject: Re: [EXT] Re: [U-Boot] [PATCH v2 1/5] spl: dm: disable SPI DM flash for non-DM SPL

Quoted 43 lines · Chuanhua Han
Quoted 43 lines

-----Original Message-----
From: Tom Rini <[email protected]>
Sent: 2019年5月24日 22:24
To: Chuanhua Han <[email protected]>
Cc: jagan at openedev.com; wd at denx.de; Shengzhou Liu <[email protected]>; Ruchika Gupta <[email protected]>; Pan Jiafei <[email protected]>; u-boot at lists.denx.de; Jiafei Pan <[email protected]>; Yinbo Zhu <[email protected]>
Subject: [EXT] Re: [U-Boot] [PATCH v2 1/5] spl: dm: disable SPI DM flash for non-DM SPL

Quoted 17 lines · Chuanhua Han

This patch solves the problem that spiboot cannot be performed in non-DM SPL.

---
Changes in v2:
- No change.

 include/config_uncmd_spl.h | 1 +
 1 file changed, 1 insertion(+)
(quoted diff) +0 -0

b/include/config_uncmd_spl.h index c2f9735ce7..da94b3d9df 100644

include/config_uncmd_spl.h line 21

Quoted 7 lines
include/config_uncmd_spl.h +1 -0
@@ -15,6 +15,7 @@
 #undef CONFIG_DM_GPIO
 #undef CONFIG_DM_I2C
 #undef CONFIG_DM_SPI
+#undef CONFIG_DM_SPI_FLASH
 #endif
 
 #undef CONFIG_DM_WARN

Long term, this shows places where we need CONFIG_SPL_DM_xxx and code should be using CONFIG_IS_ENABLED(DM_xxx). Please update at least the DM_SPI_FLASH case you're finding to behave like that, thanks!

Quoted 8 lines
Quoted 6 lines
Quoted 1 line

I don't understand you very much. Are you saying to modify the spi-flash

related code?

Correct. include/config_uncmd_spl.h should be removed as there should, long term, be no cases of code in SPL that we can / should exclude not guarded by CONFIG_SPL_xxx instead.

Do you mean I should not add "#undef CONFIG_DM_SPI_FLASH" in include/config_uncmd_spl.h? What should I do? Is there any code or file for reference?

You should fix whatever code is being linked in to SPL that should not be in SPL to use CONFIG_IS_ENABLED(DM_SPI_FLASH) and add a SPL_DM_SPI_FLASH symbol so that platforms which do need it can still enable it. Thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190603/256d0bac/attachment.sig>
#13 lore raw
In reply to Tom Rini
Quoted 57 lines

-----Original Message-----
From: Tom Rini <[email protected]>
Sent: 2019年5月31日 3:43
To: Chuanhua Han <[email protected]>
Cc: jagan at openedev.com; wd at denx.de; Shengzhou Liu <[email protected]>; Ruchika Gupta <[email protected]>; Pan Jiafei <[email protected]>; u-boot at lists.denx.de; Jiafei Pan <[email protected]>; Yinbo Zhu <[email protected]>
Subject: Re: [EXT] Re: [U-Boot] [PATCH v2 1/5] spl: dm: disable SPI DM flash for non-DM SPL

Quoted 43 lines · Chuanhua Han
Quoted 43 lines

-----Original Message-----
From: Tom Rini <[email protected]>
Sent: 2019年5月24日 22:24
To: Chuanhua Han <[email protected]>
Cc: jagan at openedev.com; wd at denx.de; Shengzhou Liu <[email protected]>; Ruchika Gupta <[email protected]>; Pan Jiafei <[email protected]>; u-boot at lists.denx.de; Jiafei Pan <[email protected]>; Yinbo Zhu <[email protected]>
Subject: [EXT] Re: [U-Boot] [PATCH v2 1/5] spl: dm: disable SPI DM flash for non-DM SPL

Quoted 17 lines · Chuanhua Han

This patch solves the problem that spiboot cannot be performed in non-DM SPL.

---
Changes in v2:
- No change.

 include/config_uncmd_spl.h | 1 +
 1 file changed, 1 insertion(+)
(quoted diff) +0 -0

b/include/config_uncmd_spl.h index c2f9735ce7..da94b3d9df 100644

include/config_uncmd_spl.h line 21

Quoted 7 lines
include/config_uncmd_spl.h +1 -0
@@ -15,6 +15,7 @@
 #undef CONFIG_DM_GPIO
 #undef CONFIG_DM_I2C
 #undef CONFIG_DM_SPI
+#undef CONFIG_DM_SPI_FLASH
 #endif
 
 #undef CONFIG_DM_WARN

Long term, this shows places where we need CONFIG_SPL_DM_xxx and code should be using CONFIG_IS_ENABLED(DM_xxx). Please update at least the DM_SPI_FLASH case you're finding to behave like that, thanks!

Quoted 6 lines
Quoted 1 line

I don't understand you very much. Are you saying to modify the spi-flash

related code?

Correct. include/config_uncmd_spl.h should be removed as there should, long term, be no cases of code in SPL that we can / should exclude not guarded by CONFIG_SPL_xxx instead.

Do you mean include/config_uncmd_spl.h will be deleted in the future? Why did you start adding this file?

Quoted 3 lines

--
Tom

#14 lore raw
Quoted 57 lines · Chuanhua Han
Quoted 57 lines

-----Original Message-----
From: Tom Rini <[email protected]>
Sent: 2019年5月31日 3:43
To: Chuanhua Han <[email protected]>
Cc: jagan at openedev.com; wd at denx.de; Shengzhou Liu <[email protected]>; Ruchika Gupta <[email protected]>; Pan Jiafei <[email protected]>; u-boot at lists.denx.de; Jiafei Pan <[email protected]>; Yinbo Zhu <[email protected]>
Subject: Re: [EXT] Re: [U-Boot] [PATCH v2 1/5] spl: dm: disable SPI DM flash for non-DM SPL

Quoted 43 lines · Chuanhua Han
Quoted 43 lines

-----Original Message-----
From: Tom Rini <[email protected]>
Sent: 2019年5月24日 22:24
To: Chuanhua Han <[email protected]>
Cc: jagan at openedev.com; wd at denx.de; Shengzhou Liu <[email protected]>; Ruchika Gupta <[email protected]>; Pan Jiafei <[email protected]>; u-boot at lists.denx.de; Jiafei Pan <[email protected]>; Yinbo Zhu <[email protected]>
Subject: [EXT] Re: [U-Boot] [PATCH v2 1/5] spl: dm: disable SPI DM flash for non-DM SPL

Quoted 17 lines · Chuanhua Han

This patch solves the problem that spiboot cannot be performed in non-DM SPL.

---
Changes in v2:
- No change.

 include/config_uncmd_spl.h | 1 +
 1 file changed, 1 insertion(+)
(quoted diff) +0 -0

b/include/config_uncmd_spl.h index c2f9735ce7..da94b3d9df 100644

include/config_uncmd_spl.h line 21

Quoted 7 lines
include/config_uncmd_spl.h +1 -0
@@ -15,6 +15,7 @@
 #undef CONFIG_DM_GPIO
 #undef CONFIG_DM_I2C
 #undef CONFIG_DM_SPI
+#undef CONFIG_DM_SPI_FLASH
 #endif
 
 #undef CONFIG_DM_WARN

Long term, this shows places where we need CONFIG_SPL_DM_xxx and code should be using CONFIG_IS_ENABLED(DM_xxx). Please update at least the DM_SPI_FLASH case you're finding to behave like that, thanks!

Quoted 8 lines
Quoted 6 lines
Quoted 1 line

I don't understand you very much. Are you saying to modify the spi-flash

related code?

Correct. include/config_uncmd_spl.h should be removed as there should, long term, be no cases of code in SPL that we can / should exclude not guarded by CONFIG_SPL_xxx instead.

Do you mean include/config_uncmd_spl.h will be deleted in the future? Why did you start adding this file?

The file config_uncmd_spl.h predates the CONFIG_IS_ENABLED() macro and whats left in that file should have code in question migrated to use CONFIG_IS_ENABLED(xxx) and as needed new CONFIG_SPL_xxx symbols added, in case some places _do_ need it.

I'm not asking you to do this migrated, but I don't want to see more technical debt added here. We can solve the problem you're seeing around CONFIG_DM_SPI_FLASH in another easier to maintain manner. Thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190603/b0408f8a/attachment.sig>