Skip to contentSkip to conversation

ARM: zii-rdu2: disable eth0 and eth1

PATCH NAK Vivien Didelot 3 participants 6 messages Jun 10, 2019 – Jun 11, 2019

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ARM: zii-rdu2: disable eth0 and eth1

The current support for the ZII RDU2 Board times out on eth0 and eth1 when booting 'net' from an alternative interface, like a USB Ethernet dongle. eth0 is the DSA master interface and has no use within barebox, as well as the gigabit interface eth1 which is wired to the switch port 0. Disable them to allow Barebox to boot right away from network.

---
 arch/arm/boards/zii-imx6q-rdu2/defaultenv-rdu2/nv/dev.eth0.mode | 1 +
 arch/arm/boards/zii-imx6q-rdu2/defaultenv-rdu2/nv/dev.eth1.mode | 1 +
 2 files changed, 2 insertions(+)
 create mode 100644 arch/arm/boards/zii-imx6q-rdu2/defaultenv-rdu2/nv/dev.eth0.mode
 create mode 100644 arch/arm/boards/zii-imx6q-rdu2/defaultenv-rdu2/nv/dev.eth1.mode
arch/arm/boards/zii-imx6q-rdu2/defaultenv-rdu2/nv/dev.eth0.mode new file +1 -0
new file mode 100644
index 000000000..87e7bdaae
@@ -0,0 +1 @@
+disabled
\ No newline at end of file
arch/arm/boards/zii-imx6q-rdu2/defaultenv-rdu2/nv/dev.eth1.mode new file +1 -0
new file mode 100644
index 000000000..87e7bdaae
@@ -0,0 +1 @@
+disabled
\ No newline at end of file
Signature · 7 lines
2.21.0


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#1 lore raw
Quoted 7 lines · Vivien Didelot

The current support for the ZII RDU2 Board times out on eth0 and eth1 when booting 'net' from an alternative interface, like a USB Ethernet dongle. eth0 is the DSA master interface and has no use within barebox, as well as the gigabit interface eth1 which is wired to the switch port 0. Disable them to allow Barebox to boot right away from network.

I personally don't have any preference as far as this is concerned, since I usually override all of those settings and disable DSA in the switch anyway. However we might want to wait to hear back from Lucas or other folks at Pengutronix who dealt with RDU2, since this patch might go against how they use it.

Thanks,
Andrey Smirnov

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox

#2 lore raw
In reply to Vivien Didelot

Am Montag, den 10.06.2019, 11:58 -0400 schrieb Vivien Didelot:

Quoted 5 lines

The current support for the ZII RDU2 Board times out on eth0 and eth1 when booting 'net' from an alternative interface, like a USB Ethernet dongle. eth0 is the DSA master interface and has no use within barebox, as well as the gigabit interface eth1 which is wired to the switch port 0. Disable them to allow Barebox to boot right away from network.

NACK.

With the just merged patches to the RDU2 environment the FEC interface is fully usable for regular network boot, which is what I use for my development setups.

As USB network boot requires additional hardware, I would say it's fair to require to change the environment on the boards used for DSA development.

Regards,
Lucas

Quoted 22 lines
---
 arch/arm/boards/zii-imx6q-rdu2/defaultenv-rdu2/nv/dev.eth0.mode | 1 +
 arch/arm/boards/zii-imx6q-rdu2/defaultenv-rdu2/nv/dev.eth1.mode | 1 +
 2 files changed, 2 insertions(+)
 create mode 100644 arch/arm/boards/zii-imx6q-rdu2/defaultenv-rdu2/nv/dev.eth0.mode
 create mode 100644 arch/arm/boards/zii-imx6q-rdu2/defaultenv-rdu2/nv/dev.eth1.mode
arch/arm/boards/zii-imx6q-rdu2/defaultenv-rdu2/nv/dev.eth0.mode new file +1 -0
new file mode 100644
index 000000000..87e7bdaae
@@ -0,0 +1 @@
+disabled
\ No newline at end of file
arch/arm/boards/zii-imx6q-rdu2/defaultenv-rdu2/nv/dev.eth1.mode new file +0 -0
new file mode 100644
index 000000000..87e7bdaae

arch/arm/boards/zii-imx6q-rdu2/defaultenv-rdu2/nv/dev.eth1.mode line 1

Quoted 2 lines
arch/arm/boards/zii-imx6q-rdu2/defaultenv-rdu2/nv/dev.eth1.mode new file +1 -0
@@ -0,0 +1 @@
+disabled
\ No newline at end of file

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox

#3 lore raw

Hi Lucas,

Quoted 7 lines · Lucas Stach

Am Montag, den 10.06.2019, 11:58 -0400 schrieb Vivien Didelot:

Quoted 5 lines

The current support for the ZII RDU2 Board times out on eth0 and eth1 when booting 'net' from an alternative interface, like a USB Ethernet dongle. eth0 is the DSA master interface and has no use within barebox, as well as the gigabit interface eth1 which is wired to the switch port 0. Disable them to allow Barebox to boot right away from network.

Quoted 5 lines

NACK.

With the just merged patches to the RDU2 environment the FEC interface is fully usable for regular network boot, which is what I use for my development setups.

Do you mean we can now use one of netleft, netaux or netright to tftpboot?

Quoted 3 lines

As USB network boot requires additional hardware, I would say it's fair to require to change the environment on the boards used for DSA development.

I'd certainly agree with that if booting from a DSA slave is now possible.

Thanks,
Vivien

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox

#4 lore raw

Hi Vivien,

Am Dienstag, den 11.06.2019, 10:46 -0400 schrieb Vivien Didelot:

Quoted 10 lines

Hi Lucas,

Quoted 7 lines · Lucas Stach

Am Montag, den 10.06.2019, 11:58 -0400 schrieb Vivien Didelot:

Quoted 5 lines

The current support for the ZII RDU2 Board times out on eth0 and eth1 when booting 'net' from an alternative interface, like a USB Ethernet dongle. eth0 is the DSA master interface and has no use within barebox, as well as the gigabit interface eth1 which is wired to the switch port 0. Disable them to allow Barebox to boot right away from network.

Quoted 7 lines
Quoted 5 lines

NACK.

With the just merged patches to the RDU2 environment the FEC interface is fully usable for regular network boot, which is what I use for my development setups.

Do you mean we can now use one of netleft, netaux or netright to tftpboot?

The default switch config on my units is pass-through. I don't know if this is true for all units, it may have changed at some point. The patches in barebox/next make sure that the switch is reset when trying to bring the network interface up. With this configuration you can use any of the netleft/netright/netaux connectors to do regular netboot.

Quoted 5 lines
Quoted 3 lines

As USB network boot requires additional hardware, I would say it's fair to require to change the environment on the boards used for DSA development.

I'd certainly agree with that if booting from a DSA slave is now possible.

For DSA development you will still need a USB network dongle, but for all development that hasn't to do with the ethernet switch, netbooting from Barebox works fine with the default configuration.

Regards,
Lucas

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox

#5 lore raw

Hi Lucas,

Quoted 9 lines · Lucas Stach
Quoted 5 lines
Quoted 3 lines

As USB network boot requires additional hardware, I would say it's fair to require to change the environment on the boards used for DSA development.

I'd certainly agree with that if booting from a DSA slave is now possible.

For DSA development you will still need a USB network dongle, but for all development that hasn't to do with the ethernet switch, netbooting from Barebox works fine with the default configuration.

For that reason I agree with you to keep this patch out-of-tree.

Thank you,
Vivien

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox