mac80211/ath11k: HE mesh support
Subsystems (4)
v2 cover mac80211/ath11k: HE mesh support
Hi,
Some features of 802.11ax without central organizing (AP) STA can also be used in mesh mode. The main goal is to get this working for ath11k. But there are various problems at the moment with the firmware. I hangs from time to time during assoc (especially when using HE) or just doesn't enable HE rates when communicating with peers. Even when the peer was successfully detected as HE capable by the upper layers:
root@OpenWrt:/# cat /sys/kernel/debug/ieee80211/phy2/netdev:mesh2/stations/00:03:7f:12:bb:97/he_capa
HE supported
MAC-CAP: 0x09 0x0d 0x08 0x0a 0x40 0x00
HTC-HE
DYNAMIC-FRAG-LEVEL-1
MAX-NUM-FRAG-MSDU-1
MIN-FRAG-SIZE-128
TF-MAC-PAD-DUR-24US
MULTI-TID-AGG-RX-QOS-1
LINK-ADAPTATION-NO-FEEDBACK
BSR
OMI-CONTROL
MAX-AMPDU-LEN-EXP-VHT-1
AMSDU-IN-AMPDU
MULTI-TID-AGG-TX-QOS-0
PHY CAP: 0x1c 0x70 0x0c 0x80 0x0d 0x43 0x81 0x1c 0x00 0x00 0x00
CHANNEL-WIDTH-SET-40MHZ-80MHZ-IN-5G
CHANNEL-WIDTH-SET-160MHZ-IN-5G
CHANNEL-WIDTH-SET-80PLUS80-MHZ-IN-5G
IEEE80211-HE-PHY-CAP1-DEVICE-CLASS-A
LDPC-CODING-IN-PAYLOAD
HY-CAP1-HE-LTF-AND-GI-FOR-HE-PPDUS-0-8US
MIDAMBLE-RX-MAX-NSTS-0
STBC-TX-UNDER-80MHZ
STBC-RX-UNDER-80MHZ
DCM-MAX-CONST-TX-NO-DCM
DCM-MAX-CONST-RX-NO-DCM
SU-BEAMFORMER
SU-BEAMFORMEE
BEAMFORMEE-MAX-STS-UNDER-7
BEAMFORMEE-MAX-STS-ABOVE-4
NUM-SND-DIM-UNDER-80MHZ-4
NUM-SND-DIM-ABOVE-80MHZ-1
NG16-SU-FEEDBACK
CODEBOOK-SIZE-42-SU
PPE-THRESHOLD-PRESENT
HE-SU-MU-PPDU-4XLTF-AND-08-US-GI
MAX-NC-4
DCM-MAX-RU-242
NOMINAL-PACKET-PADDING-0US
RX-MCS-80: 0xffaa
RX-MCS-80-0-SUPPORT-0-11
RX-MCS-80-1-SUPPORT-0-11
RX-MCS-80-2-SUPPORT-0-11
RX-MCS-80-3-SUPPORT-0-11
TX-MCS-80: 0xffaa
TX-MCS-80-0-SUPPORT-0-11
TX-MCS-80-1-SUPPORT-0-11
TX-MCS-80-2-SUPPORT-0-11
TX-MCS-80-3-SUPPORT-0-11
RX-MCS-160: 0xfffa
RX-MCS-160-0-SUPPORT-0-11
RX-MCS-160-1-SUPPORT-0-11
RX-MCS-160-2-NOT-SUPPORTED
RX-MCS-160-3-NOT-SUPPORTED
TX-MCS-160: 0xfffa
TX-MCS-160-0-SUPPORT-0-11
TX-MCS-160-1-SUPPORT-0-11
TX-MCS-160-2-NOT-SUPPORTED
TX-MCS-160-3-NOT-SUPPORTED
RX-MCS-80P80: 0xfffa
RX-MCS-80P80-0-SUPPORT-0-11
RX-MCS-80P80-1-SUPPORT-0-11
RX-MCS-80P80-2-NOT-SUPPORTED
RX-MCS-80P80-3-NOT-SUPPORTED
TX-MCS-80P80: 0xfffa
TX-MCS-80P80-0-SUPPORT-0-11
TX-MCS-80P80-1-SUPPORT-0-11
TX-MCS-80P80-2-NOT-SUPPORTED
TX-MCS-80P80-3-NOT-SUPPORTED
PPE-THRESHOLDS: 0x3b 0x1c 0xc7 0x71 0x1c 0xc7 0x71 0x1c 0xc7 0x71
root@OpenWrt:/# iw dev mesh2 station dump
Station 00:03:7f:12:bb:97 (on mesh2)
inactive time: 310 ms
rx bytes: 161064
rx packets: 1619
tx bytes: 55454
tx packets: 477
tx retries: 405
tx failed: 0
rx drop misc: 6
signal: -95 dBm
signal avg: -67 dBm
tx bitrate: 1733.3 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 4
rx bitrate: 1733.3 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 4
rx duration: 0 us
mesh llid: 0
mesh plid: 0
mesh plink: ESTAB
mesh local PS mode: ACTIVE
mesh peer PS mode: ACTIVE
mesh non-peer PS mode: ACTIVE
authorized: yes
authenticated: yes
associated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 2
beacon interval:1000
connected time: 536 secondsBut there is currently no documentation what the firmware requires (next to the already existing things for AP/managed) to enable HE for mesh.
hwsim can be used in the meantime as basis for initial development of these features without having access to HW.
Kind regards,
Sven
Sven Eckelmann (3):
mac80211_hwsim: Register support for HE meshpoint
mac80211: implement HE support for mesh
ath11k: register HE mesh capabilities
drivers/net/wireless/ath/ath11k/mac.c | 56 +++++ drivers/net/wireless/mac80211_hwsim.c | 283 +++++++++++++++++--------- include/net/cfg80211.h | 19 ++ net/mac80211/ieee80211_i.h | 2 + net/mac80211/mesh.c | 61 ++++++ net/mac80211/mesh.h | 4 + net/mac80211/mesh_plink.c | 11 +- net/mac80211/util.c | 52 +++++ 8 files changed, 393 insertions(+), 95 deletions(-)
Signature · 7 lines
2.20.1 _______________________________________________ ath11k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath11k
RFC PATCH v2 1/3 mac80211_hwsim: Register support for HE meshpoint
From: Sven Eckelmann <[email protected]>
Some features of 802.11ax without central organizing (AP) STA can also be used in mesh mode. hwsim can be used to assist initial development of these features without having access to HW.
--- drivers/net/wireless/mac80211_hwsim.c | 283 +++++++++++++++++--------- 1 file changed, 189 insertions(+), 94 deletions(-)
drivers/net/wireless/mac80211_hwsim.c +189 -94
@@ -2501,116 +2501,211 @@ static void hwsim_mcast_new_radio(int id, struct genl_info *info,nlmsg_free (mcast_skb); } -static const struct ieee80211_sband_iftype_data he_capa_2ghz = { -/* TODO: should we support other types, e.g., P2P?*/ - .types_mask =BIT (NL80211_IFTYPE_STATION ) |BIT (NL80211_IFTYPE_AP ), - .he_cap = { - .has_he = true, - .he_cap_elem = { - .mac_cap_info[0 ] = -IEEE80211_HE_MAC_CAP0_HTC_HE , - .mac_cap_info[1 ] = -IEEE80211_HE_MAC_CAP1_TF_MAC_PAD_DUR_16US | -IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_8 , - .mac_cap_info[2 ] = -IEEE80211_HE_MAC_CAP2_BSR | -IEEE80211_HE_MAC_CAP2_MU_CASCADING | -IEEE80211_HE_MAC_CAP2_ACK_EN , - .mac_cap_info[3 ] = -IEEE80211_HE_MAC_CAP3_OMI_CONTROL | -IEEE80211_HE_MAC_CAP3_MAX_AMPDU_LEN_EXP_VHT_2 , - .mac_cap_info[4 ] =IEEE80211_HE_MAC_CAP4_AMDSU_IN_AMPDU , - .phy_cap_info[1 ] = -IEEE80211_HE_PHY_CAP1_PREAMBLE_PUNC_RX_MASK | -IEEE80211_HE_PHY_CAP1_DEVICE_CLASS_A | -IEEE80211_HE_PHY_CAP1_LDPC_CODING_IN_PAYLOAD | -IEEE80211_HE_PHY_CAP1_MIDAMBLE_RX_TX_MAX_NSTS , - .phy_cap_info[2 ] = - IEEE80211_HE_PHY_CAP2_NDP_4x_LTF_AND_3_2US | -IEEE80211_HE_PHY_CAP2_STBC_TX_UNDER_80MHZ | -IEEE80211_HE_PHY_CAP2_STBC_RX_UNDER_80MHZ | -IEEE80211_HE_PHY_CAP2_UL_MU_FULL_MU_MIMO | -IEEE80211_HE_PHY_CAP2_UL_MU_PARTIAL_MU_MIMO , - -/* Leave all the other PHY capability bytes unset, as -* DCM, beam forming, RU and PPE threshold information -* are not supported -*/ +static const struct ieee80211_sband_iftype_data he_capa_2ghz[] = { + { +/* TODO: should we support other types, e.g., P2P?*/ + .types_mask =BIT (NL80211_IFTYPE_STATION ) | +BIT (NL80211_IFTYPE_AP ), + .he_cap = { + .has_he = true, + .he_cap_elem = { + .mac_cap_info[0 ] = +IEEE80211_HE_MAC_CAP0_HTC_HE , + .mac_cap_info[1 ] = +IEEE80211_HE_MAC_CAP1_TF_MAC_PAD_DUR_16US | +IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_8 , + .mac_cap_info[2 ] = +IEEE80211_HE_MAC_CAP2_BSR | +IEEE80211_HE_MAC_CAP2_MU_CASCADING | +IEEE80211_HE_MAC_CAP2_ACK_EN , + .mac_cap_info[3 ] = +IEEE80211_HE_MAC_CAP3_OMI_CONTROL | +IEEE80211_HE_MAC_CAP3_MAX_AMPDU_LEN_EXP_VHT_2 , + .mac_cap_info[4 ] =IEEE80211_HE_MAC_CAP4_AMDSU_IN_AMPDU , + .phy_cap_info[1 ] = +IEEE80211_HE_PHY_CAP1_PREAMBLE_PUNC_RX_MASK | +IEEE80211_HE_PHY_CAP1_DEVICE_CLASS_A | +IEEE80211_HE_PHY_CAP1_LDPC_CODING_IN_PAYLOAD | +IEEE80211_HE_PHY_CAP1_MIDAMBLE_RX_TX_MAX_NSTS , + .phy_cap_info[2 ] = + IEEE80211_HE_PHY_CAP2_NDP_4x_LTF_AND_3_2US | +IEEE80211_HE_PHY_CAP2_STBC_TX_UNDER_80MHZ | +IEEE80211_HE_PHY_CAP2_STBC_RX_UNDER_80MHZ | +IEEE80211_HE_PHY_CAP2_UL_MU_FULL_MU_MIMO | +IEEE80211_HE_PHY_CAP2_UL_MU_PARTIAL_MU_MIMO , + +/* Leave all the other PHY capability bytes +* unset, as DCM, beam forming, RU and PPE +* threshold information are not supported +*/ + }, + .he_mcs_nss_supp = { + .rx_mcs_80 =cpu_to_le16 (0xfffa ), + .tx_mcs_80 =cpu_to_le16 (0xfffa ), + .rx_mcs_160 =cpu_to_le16 (0xffff ), + .tx_mcs_160 =cpu_to_le16 (0xffff ), + .rx_mcs_80p80 =cpu_to_le16 (0xffff ), + .tx_mcs_80p80 =cpu_to_le16 (0xffff ), + }, }, - .he_mcs_nss_supp = { - .rx_mcs_80 =cpu_to_le16 (0xfffa ), - .tx_mcs_80 =cpu_to_le16 (0xfffa ), - .rx_mcs_160 =cpu_to_le16 (0xffff ), - .tx_mcs_160 =cpu_to_le16 (0xffff ), - .rx_mcs_80p80 =cpu_to_le16 (0xffff ), - .tx_mcs_80p80 =cpu_to_le16 (0xffff ), + }, +#ifdef CONFIG_MAC80211_MESH + { +/* TODO: should we support other types, e.g., IBSS?*/ + .types_mask =BIT (NL80211_IFTYPE_MESH_POINT ), + .he_cap = { + .has_he = true, + .he_cap_elem = { + .mac_cap_info[0 ] = +IEEE80211_HE_MAC_CAP0_HTC_HE , + .mac_cap_info[1 ] = +IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_8 , + .mac_cap_info[2 ] = +IEEE80211_HE_MAC_CAP2_ACK_EN , + .mac_cap_info[3 ] = +IEEE80211_HE_MAC_CAP3_OMI_CONTROL | +IEEE80211_HE_MAC_CAP3_MAX_AMPDU_LEN_EXP_VHT_2 , + .mac_cap_info[4 ] =IEEE80211_HE_MAC_CAP4_AMDSU_IN_AMPDU , + .phy_cap_info[1 ] = +IEEE80211_HE_PHY_CAP1_PREAMBLE_PUNC_RX_MASK | +IEEE80211_HE_PHY_CAP1_DEVICE_CLASS_A | +IEEE80211_HE_PHY_CAP1_LDPC_CODING_IN_PAYLOAD | +IEEE80211_HE_PHY_CAP1_MIDAMBLE_RX_TX_MAX_NSTS , + .phy_cap_info[2 ] =0 , + +/* Leave all the other PHY capability bytes +* unset, as DCM, beam forming, RU and PPE +* threshold information are not supported +*/ + }, + .he_mcs_nss_supp = { + .rx_mcs_80 =cpu_to_le16 (0xfffa ), + .tx_mcs_80 =cpu_to_le16 (0xfffa ), + .rx_mcs_160 =cpu_to_le16 (0xffff ), + .tx_mcs_160 =cpu_to_le16 (0xffff ), + .rx_mcs_80p80 =cpu_to_le16 (0xffff ), + .tx_mcs_80p80 =cpu_to_le16 (0xffff ), + }, }, }, +#endif }; -static const struct ieee80211_sband_iftype_data he_capa_5ghz = { -/* TODO: should we support other types, e.g., P2P?*/ - .types_mask =BIT (NL80211_IFTYPE_STATION ) |BIT (NL80211_IFTYPE_AP ), - .he_cap = { - .has_he = true, - .he_cap_elem = { - .mac_cap_info[0 ] = -IEEE80211_HE_MAC_CAP0_HTC_HE , - .mac_cap_info[1 ] = -IEEE80211_HE_MAC_CAP1_TF_MAC_PAD_DUR_16US | -IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_8 , - .mac_cap_info[2 ] = -IEEE80211_HE_MAC_CAP2_BSR | -IEEE80211_HE_MAC_CAP2_MU_CASCADING | -IEEE80211_HE_MAC_CAP2_ACK_EN , - .mac_cap_info[3 ] = -IEEE80211_HE_MAC_CAP3_OMI_CONTROL | -IEEE80211_HE_MAC_CAP3_MAX_AMPDU_LEN_EXP_VHT_2 , - .mac_cap_info[4 ] =IEEE80211_HE_MAC_CAP4_AMDSU_IN_AMPDU , - .phy_cap_info[0 ] = -IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_80MHZ_IN_5G | -IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G | -IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G , - .phy_cap_info[1 ] = -IEEE80211_HE_PHY_CAP1_PREAMBLE_PUNC_RX_MASK | -IEEE80211_HE_PHY_CAP1_DEVICE_CLASS_A | -IEEE80211_HE_PHY_CAP1_LDPC_CODING_IN_PAYLOAD | -IEEE80211_HE_PHY_CAP1_MIDAMBLE_RX_TX_MAX_NSTS , - .phy_cap_info[2 ] = - IEEE80211_HE_PHY_CAP2_NDP_4x_LTF_AND_3_2US | -IEEE80211_HE_PHY_CAP2_STBC_TX_UNDER_80MHZ | -IEEE80211_HE_PHY_CAP2_STBC_RX_UNDER_80MHZ | -IEEE80211_HE_PHY_CAP2_UL_MU_FULL_MU_MIMO | -IEEE80211_HE_PHY_CAP2_UL_MU_PARTIAL_MU_MIMO , - -/* Leave all the other PHY capability bytes unset, as -* DCM, beam forming, RU and PPE threshold information -* are not supported -*/ +static const struct ieee80211_sband_iftype_data he_capa_5ghz[] = { + { +/* TODO: should we support other types, e.g., P2P?*/ + .types_mask =BIT (NL80211_IFTYPE_STATION ) | +BIT (NL80211_IFTYPE_AP ), + .he_cap = { + .has_he = true, + .he_cap_elem = { + .mac_cap_info[0 ] = +IEEE80211_HE_MAC_CAP0_HTC_HE , + .mac_cap_info[1 ] = +IEEE80211_HE_MAC_CAP1_TF_MAC_PAD_DUR_16US | +IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_8 , + .mac_cap_info[2 ] = +IEEE80211_HE_MAC_CAP2_BSR | +IEEE80211_HE_MAC_CAP2_MU_CASCADING | +IEEE80211_HE_MAC_CAP2_ACK_EN , + .mac_cap_info[3 ] = +IEEE80211_HE_MAC_CAP3_OMI_CONTROL | +IEEE80211_HE_MAC_CAP3_MAX_AMPDU_LEN_EXP_VHT_2 , + .mac_cap_info[4 ] =IEEE80211_HE_MAC_CAP4_AMDSU_IN_AMPDU , + .phy_cap_info[0 ] = +IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_80MHZ_IN_5G | +IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G | +IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G , + .phy_cap_info[1 ] = +IEEE80211_HE_PHY_CAP1_PREAMBLE_PUNC_RX_MASK | +IEEE80211_HE_PHY_CAP1_DEVICE_CLASS_A | +IEEE80211_HE_PHY_CAP1_LDPC_CODING_IN_PAYLOAD | +IEEE80211_HE_PHY_CAP1_MIDAMBLE_RX_TX_MAX_NSTS , + .phy_cap_info[2 ] = + IEEE80211_HE_PHY_CAP2_NDP_4x_LTF_AND_3_2US | +IEEE80211_HE_PHY_CAP2_STBC_TX_UNDER_80MHZ | +IEEE80211_HE_PHY_CAP2_STBC_RX_UNDER_80MHZ | +IEEE80211_HE_PHY_CAP2_UL_MU_FULL_MU_MIMO | +IEEE80211_HE_PHY_CAP2_UL_MU_PARTIAL_MU_MIMO , + +/* Leave all the other PHY capability bytes +* unset, as DCM, beam forming, RU and PPE +* threshold information are not supported +*/ + }, + .he_mcs_nss_supp = { + .rx_mcs_80 =cpu_to_le16 (0xfffa ), + .tx_mcs_80 =cpu_to_le16 (0xfffa ), + .rx_mcs_160 =cpu_to_le16 (0xfffa ), + .tx_mcs_160 =cpu_to_le16 (0xfffa ), + .rx_mcs_80p80 =cpu_to_le16 (0xfffa ), + .tx_mcs_80p80 =cpu_to_le16 (0xfffa ), + }, }, - .he_mcs_nss_supp = { - .rx_mcs_80 =cpu_to_le16 (0xfffa ), - .tx_mcs_80 =cpu_to_le16 (0xfffa ), - .rx_mcs_160 =cpu_to_le16 (0xfffa ), - .tx_mcs_160 =cpu_to_le16 (0xfffa ), - .rx_mcs_80p80 =cpu_to_le16 (0xfffa ), - .tx_mcs_80p80 =cpu_to_le16 (0xfffa ), + }, +#ifdef CONFIG_MAC80211_MESH + { +/* TODO: should we support other types, e.g., IBSS?*/ + .types_mask =BIT (NL80211_IFTYPE_MESH_POINT ), + .he_cap = { + .has_he = true, + .he_cap_elem = { + .mac_cap_info[0 ] = +IEEE80211_HE_MAC_CAP0_HTC_HE , + .mac_cap_info[1 ] = +IEEE80211_HE_MAC_CAP1_MULTI_TID_AGG_RX_QOS_8 , + .mac_cap_info[2 ] = +IEEE80211_HE_MAC_CAP2_ACK_EN , + .mac_cap_info[3 ] = +IEEE80211_HE_MAC_CAP3_OMI_CONTROL | +IEEE80211_HE_MAC_CAP3_MAX_AMPDU_LEN_EXP_VHT_2 , + .mac_cap_info[4 ] =IEEE80211_HE_MAC_CAP4_AMDSU_IN_AMPDU , + .phy_cap_info[0 ] = +IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_80MHZ_IN_5G | +IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G | +IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G , + .phy_cap_info[1 ] = +IEEE80211_HE_PHY_CAP1_PREAMBLE_PUNC_RX_MASK | +IEEE80211_HE_PHY_CAP1_DEVICE_CLASS_A | +IEEE80211_HE_PHY_CAP1_LDPC_CODING_IN_PAYLOAD | +IEEE80211_HE_PHY_CAP1_MIDAMBLE_RX_TX_MAX_NSTS , + .phy_cap_info[2 ] =0 , + +/* Leave all the other PHY capability bytes +* unset, as DCM, beam forming, RU and PPE +* threshold information are not supported +*/ + }, + .he_mcs_nss_supp = { + .rx_mcs_80 =cpu_to_le16 (0xfffa ), + .tx_mcs_80 =cpu_to_le16 (0xfffa ), + .rx_mcs_160 =cpu_to_le16 (0xfffa ), + .tx_mcs_160 =cpu_to_le16 (0xfffa ), + .rx_mcs_80p80 =cpu_to_le16 (0xfffa ), + .tx_mcs_80p80 =cpu_to_le16 (0xfffa ), + }, }, }, +#endif };static void mac80211_hswim_he_capab (struct ieee80211_supported_band *sband) { -if (sband->band ==NL80211_BAND_2GHZ ) +u16 n_iftype_data; + +if (sband->band ==NL80211_BAND_2GHZ ) { + n_iftype_data =ARRAY_SIZE (he_capa_2ghz); sband->iftype_data = - (struct ieee80211_sband_iftype_data *)&he_capa_2ghz; -else if (sband->band ==NL80211_BAND_5GHZ ) + (struct ieee80211_sband_iftype_data *)he_capa_2ghz; + }else if (sband->band ==NL80211_BAND_5GHZ ) { + n_iftype_data =ARRAY_SIZE (he_capa_5ghz); sband->iftype_data = - (struct ieee80211_sband_iftype_data *)&he_capa_5ghz; -else + (struct ieee80211_sband_iftype_data *)he_capa_5ghz; + }else {return ; + } - sband->n_iftype_data =1 ; + sband->n_iftype_data = n_iftype_data; }#ifdef CONFIG_MAC80211_MESH
Signature · 7 lines
2.20.1 _______________________________________________ ath11k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath11k
RFC PATCH v2 2/3 mac80211: implement HE support for mesh
In reply to Sven EckelmannFrom: Sven Eckelmann <[email protected]>
Implement the basics required for supporting high efficiency with mesh:
include HE information elements in beacons, probe responses, and peering action frames, and check for compatible HE configurations when peering.
--- include/net/cfg80211.h | 19 ++++++++++++ net/mac80211/ieee80211_i.h | 2 ++ net/mac80211/mesh.c | 61 ++++++++++++++++++++++++++++++++++++++ net/mac80211/mesh.h | 4 +++ net/mac80211/mesh_plink.c | 11 ++++++- net/mac80211/util.c | 52 ++++++++++++++++++++++++++++++++ 6 files changed, 148 insertions(+), 1 deletion(-)
include/net/cfg80211.h +19 -0
@@ -399,6 +399,25 @@ ieee80211_get_he_sta_cap(const struct ieee80211_supported_band *sband)return NULL ; } +/** +* ieee80211_get_he_mesh_cap - return HE capabilities for an sband's mesh STA +* @sband: the sband to search for the mesh STA on +* +* Return: pointer to the struct ieee80211_sta_he_cap, or NULL is none found +*/ +static inline const struct ieee80211_sta_he_cap * +ieee80211_get_he_mesh_cap (const struct ieee80211_supported_band *sband) +{ +const struct ieee80211_sband_iftype_data *data = +ieee80211_get_sband_iftype_data (sband, +NL80211_IFTYPE_MESH_POINT ); + +if (data && data->he_cap.has_he) +return &data->he_cap; + +return NULL ; +} +/** * wiphy_read_of_freq_limits - read frequency limits from device tree *
net/mac80211/ieee80211_i.h +2 -0
@@ -2130,9 +2130,11 @@ u8 *ieee80211_ie_build_vht_cap(u8 *pos, struct ieee80211_sta_vht_cap *vht_cap, u32 cap);u8 *ieee80211_ie_build_vht_oper (u8 *pos,struct ieee80211_sta_vht_cap *vht_cap,const struct cfg80211_chan_def *chandef); +u8 ieee80211_ie_len_he_cap (struct ieee80211_sub_if_data *sdata);u8 *ieee80211_ie_build_he_cap (u8 *pos,const struct ieee80211_sta_he_cap *he_cap,u8 *end); +u8 *ieee80211_ie_build_he_oper (u8 *pos);int ieee80211_parse_bitrates (struct cfg80211_chan_def *chandef,const struct ieee80211_supported_band *sband,const u8 *srates,int srates_len,u32 *rates);
net/mac80211/mesh.c +61 -0
91 lines not on this page · raw message
net/mac80211/mesh.h +4 -0
@@ -221,6 +221,10 @@ int mesh_add_vht_cap_ie(struct ieee80211_sub_if_data *sdata, struct sk_buff *skb);int mesh_add_vht_oper_ie (struct ieee80211_sub_if_data *sdata,struct sk_buff *skb); +int mesh_add_he_cap_ie (struct ieee80211_sub_if_data *sdata, +struct sk_buff *skb,u8 ie_len); +int mesh_add_he_oper_ie (struct ieee80211_sub_if_data *sdata, +struct sk_buff *skb);void mesh_rmc_free (struct ieee80211_sub_if_data *sdata);int mesh_rmc_init (struct ieee80211_sub_if_data *sdata);void ieee80211s_init (void );
net/mac80211/mesh_plink.c +10 -1
@@ -221,9 +221,11 @@ static int mesh_plink_frame_tx(struct ieee80211_sub_if_data *sdata,bool include_plid = false;u16 peering_proto =0 ;u8 *pos, ie_len =4 ; +u8 ie_len_he_cap; int hdr_len = offsetofend(struct ieee80211_mgmt, u.action.u.self_prot);int err = -ENOMEM ; + ie_len_he_cap =ieee80211_ie_len_he_cap (sdata); skb = dev_alloc_skb(local->tx_headroom + hdr_len + 2 + /* capability info */
@@ -236,6 +238,8 @@ static int mesh_plink_frame_tx(struct ieee80211_sub_if_data *sdata,2 +sizeof (struct ieee80211_ht_operation ) +2 +sizeof (struct ieee80211_vht_cap ) +2 +sizeof (struct ieee80211_vht_operation ) + + ie_len_he_cap + +2 +1 +sizeof (struct ieee80211_he_operation ) +2 +8 +/* peering IE */ sdata->u.mesh.ie_len);if (!skb)
@@ -324,7 +328,9 @@ static int mesh_plink_frame_tx(struct ieee80211_sub_if_data *sdata,if (mesh_add_ht_cap_ie (sdata, skb) ||mesh_add_ht_oper_ie (sdata, skb) ||mesh_add_vht_cap_ie (sdata, skb) || -mesh_add_vht_oper_ie (sdata, skb)) +mesh_add_vht_oper_ie (sdata, skb) || +mesh_add_he_cap_ie (sdata, skb, ie_len_he_cap) || +mesh_add_he_oper_ie (sdata, skb)) goto free; }
@@ -436,6 +442,9 @@ static void mesh_sta_info_init(struct ieee80211_sub_if_data *sdata,ieee80211_vht_cap_ie_to_sta_vht_cap (sdata, sband, elems->vht_cap_elem, sta); +ieee80211_he_cap_ie_to_sta_he_cap (sdata, sband, elems->he_cap, + elems->he_cap_len, sta); +if (bw != sta->sta.bandwidth) changed |=IEEE80211_RC_BW_CHANGED ;
net/mac80211/util.c +52 -0
64 lines not on this page · raw message
Signature · 7 lines
2.20.1 _______________________________________________ ath11k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath11k
RFC PATCH v2 3/3 ath11k: register HE mesh capabilities
In reply to Sven EckelmannFrom: Sven Eckelmann <[email protected]>
The capabilities for the HE mesh are generated from the capabilities reported by the fw. But the firmware only reports the overall capabilities and not the one which are specific for mesh. Some of them (TWT, MU UL/DL, TB PPDU, ...) require an infrastructure setup with a main STA (AP) controlling the operations. This is not the case for mesh and thus these capabilities are removed from the list of capabilities.
---
This doesn't work currently as expected. No HE rates are used between the two HE mesh peers:
root@OpenWrt:/# cat /sys/kernel/debug/ieee80211/phy2/netdev:mesh2/stations/00:03:7f:12:bb:97/he_capa
HE supported
MAC-CAP: 0x09 0x0d 0x08 0x0a 0x40 0x00
HTC-HE
DYNAMIC-FRAG-LEVEL-1
MAX-NUM-FRAG-MSDU-1
MIN-FRAG-SIZE-128
TF-MAC-PAD-DUR-24US
MULTI-TID-AGG-RX-QOS-1
LINK-ADAPTATION-NO-FEEDBACK
BSR
OMI-CONTROL
MAX-AMPDU-LEN-EXP-VHT-1
AMSDU-IN-AMPDU
MULTI-TID-AGG-TX-QOS-0
PHY CAP: 0x1c 0x70 0x0c 0x80 0x0d 0x43 0x81 0x1c 0x00 0x00 0x00
CHANNEL-WIDTH-SET-40MHZ-80MHZ-IN-5G
CHANNEL-WIDTH-SET-160MHZ-IN-5G
CHANNEL-WIDTH-SET-80PLUS80-MHZ-IN-5G
IEEE80211-HE-PHY-CAP1-DEVICE-CLASS-A
LDPC-CODING-IN-PAYLOAD
HY-CAP1-HE-LTF-AND-GI-FOR-HE-PPDUS-0-8US
MIDAMBLE-RX-MAX-NSTS-0
STBC-TX-UNDER-80MHZ
STBC-RX-UNDER-80MHZ
DCM-MAX-CONST-TX-NO-DCM
DCM-MAX-CONST-RX-NO-DCM
SU-BEAMFORMER
SU-BEAMFORMEE
BEAMFORMEE-MAX-STS-UNDER-7
BEAMFORMEE-MAX-STS-ABOVE-4
NUM-SND-DIM-UNDER-80MHZ-4
NUM-SND-DIM-ABOVE-80MHZ-1
NG16-SU-FEEDBACK
CODEBOOK-SIZE-42-SU
PPE-THRESHOLD-PRESENT
HE-SU-MU-PPDU-4XLTF-AND-08-US-GI
MAX-NC-4
DCM-MAX-RU-242
NOMINAL-PACKET-PADDING-0US
RX-MCS-80: 0xffaa
RX-MCS-80-0-SUPPORT-0-11
RX-MCS-80-1-SUPPORT-0-11
RX-MCS-80-2-SUPPORT-0-11
RX-MCS-80-3-SUPPORT-0-11
TX-MCS-80: 0xffaa
TX-MCS-80-0-SUPPORT-0-11
TX-MCS-80-1-SUPPORT-0-11
TX-MCS-80-2-SUPPORT-0-11
TX-MCS-80-3-SUPPORT-0-11
RX-MCS-160: 0xfffa
RX-MCS-160-0-SUPPORT-0-11
RX-MCS-160-1-SUPPORT-0-11
RX-MCS-160-2-NOT-SUPPORTED
RX-MCS-160-3-NOT-SUPPORTED
TX-MCS-160: 0xfffa
TX-MCS-160-0-SUPPORT-0-11
TX-MCS-160-1-SUPPORT-0-11
TX-MCS-160-2-NOT-SUPPORTED
TX-MCS-160-3-NOT-SUPPORTED
RX-MCS-80P80: 0xfffa
RX-MCS-80P80-0-SUPPORT-0-11
RX-MCS-80P80-1-SUPPORT-0-11
RX-MCS-80P80-2-NOT-SUPPORTED
RX-MCS-80P80-3-NOT-SUPPORTED
TX-MCS-80P80: 0xfffa
TX-MCS-80P80-0-SUPPORT-0-11
TX-MCS-80P80-1-SUPPORT-0-11
TX-MCS-80P80-2-NOT-SUPPORTED
TX-MCS-80P80-3-NOT-SUPPORTED
PPE-THRESHOLDS: 0x3b 0x1c 0xc7 0x71 0x1c 0xc7 0x71 0x1c 0xc7 0x71
root@OpenWrt:/# iw dev mesh2 station dump
Station 00:03:7f:12:bb:97 (on mesh2)
inactive time: 310 ms
rx bytes: 161064
rx packets: 1619
tx bytes: 55454
tx packets: 477
tx retries: 405
tx failed: 0
rx drop misc: 6
signal: -95 dBm
signal avg: -67 dBm
tx bitrate: 1733.3 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 4
rx bitrate: 1733.3 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 4
rx duration: 0 us
mesh llid: 0
mesh plid: 0
mesh plink: ESTAB
mesh local PS mode: ACTIVE
mesh peer PS mode: ACTIVE
mesh non-peer PS mode: ACTIVE
authorized: yes
authenticated: yes
associated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 2
beacon interval:1000
connected time: 536 secondsdrivers/net/wireless/ath/ath11k/mac.c | 56 +++++++++++++++++++++++++++ 1 file changed, 56 insertions(+)
drivers/net/wireless/ath/ath11k/mac.c +56 -0
@@ -3274,6 +3274,7 @@ static int ath11k_mac_copy_he_cap(struct ath11k *ar,switch (i) {case NL80211_IFTYPE_STATION :case NL80211_IFTYPE_AP : +case NL80211_IFTYPE_MESH_POINT :break ;default :
@@ -3314,6 +3315,61 @@ static int ath11k_mac_copy_he_cap(struct ath11k *ar, he_cap_elem->phy_cap_info[9 ] |=IEEE80211_HE_PHY_CAP9_TX_1024_QAM_LESS_THAN_242_TONE_RU ;break ; +case NL80211_IFTYPE_MESH_POINT : + he_cap_elem->mac_cap_info[0 ] &= + ~(IEEE80211_HE_MAC_CAP0_TWT_RES | +IEEE80211_HE_MAC_CAP0_TWT_REQ ); + he_cap_elem->mac_cap_info[2 ] &= + ~(IEEE80211_HE_MAC_CAP2_TRS | +IEEE80211_HE_MAC_CAP2_BCAST_TWT | +IEEE80211_HE_MAC_CAP2_MU_CASCADING ); + he_cap_elem->mac_cap_info[3 ] &= + ~(IEEE80211_HE_MAC_CAP3_FLEX_TWT_SCHED | +IEEE80211_HE_MAC_CAP2_BCAST_TWT | +IEEE80211_HE_MAC_CAP2_MU_CASCADING ); + he_cap_elem->mac_cap_info[4 ] &= + ~(IEEE80211_HE_MAC_CAP4_BSRP_BQRP_A_MPDU_AGG | +IEEE80211_HE_MAC_CAP4_BQR ); + he_cap_elem->mac_cap_info[5 ] &= + ~(IEEE80211_HE_MAC_CAP5_SUBCHAN_SELECVITE_TRANSMISSION | + IEEE80211_HE_MAC_CAP5_UL_2x996_TONE_RU | +IEEE80211_HE_MAC_CAP5_PUNCTURED_SOUNDING | +IEEE80211_HE_MAC_CAP5_HT_VHT_TRIG_FRAME_RX ); + + he_cap_elem->phy_cap_info[2 ] &= + ~(IEEE80211_HE_PHY_CAP2_UL_MU_FULL_MU_MIMO | +IEEE80211_HE_PHY_CAP2_UL_MU_PARTIAL_MU_MIMO ); + he_cap_elem->phy_cap_info[3 ] &= + ~(IEEE80211_HE_PHY_CAP3_RX_HE_MU_PPDU_FROM_NON_AP_STA | +IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_TX_MASK | +IEEE80211_HE_PHY_CAP3_DCM_MAX_CONST_RX_MASK ); + he_cap_elem->phy_cap_info[4 ] &= + ~IEEE80211_HE_PHY_CAP4_MU_BEAMFORMER ; + he_cap_elem->phy_cap_info[5 ] &= + ~IEEE80211_HE_PHY_CAP5_NG16_MU_FEEDBACK ; + he_cap_elem->phy_cap_info[6 ] &= + ~(IEEE80211_HE_PHY_CAP6_CODEBOOK_SIZE_75_MU | +IEEE80211_HE_PHY_CAP6_TRIG_MU_BEAMFORMER_FB | +IEEE80211_HE_PHY_CAP6_TRIG_CQI_FB | +IEEE80211_HE_PHY_CAP6_PARTIAL_BANDWIDTH_DL_MUMIMO ); + he_cap_elem->phy_cap_info[7 ] &= + ~(IEEE80211_HE_PHY_CAP7_SRP_BASED_SR | +IEEE80211_HE_PHY_CAP7_POWER_BOOST_FACTOR_AR | +IEEE80211_HE_PHY_CAP7_STBC_TX_ABOVE_80MHZ | +IEEE80211_HE_PHY_CAP7_STBC_RX_ABOVE_80MHZ ); + he_cap_elem->phy_cap_info[8 ] &= + ~(IEEE80211_HE_PHY_CAP8_HE_ER_SU_PPDU_4XLTF_AND_08_US_GI | +IEEE80211_HE_PHY_CAP8_20MHZ_IN_40MHZ_HE_PPDU_IN_2G | +IEEE80211_HE_PHY_CAP8_20MHZ_IN_160MHZ_HE_PPDU | +IEEE80211_HE_PHY_CAP8_80MHZ_IN_160MHZ_HE_PPDU ); + he_cap_elem->phy_cap_info[9 ] &= + ~(IEEE80211_HE_PHY_CAP9_LONGER_THAN_16_SIGB_OFDM_SYM | +IEEE80211_HE_PHY_CAP9_NON_TRIGGERED_CQI_FEEDBACK | +IEEE80211_HE_PHY_CAP9_RX_1024_QAM_LESS_THAN_242_TONE_RU | +IEEE80211_HE_PHY_CAP9_TX_1024_QAM_LESS_THAN_242_TONE_RU | +IEEE80211_HE_PHY_CAP9_RX_FULL_BW_SU_USING_MU_WITH_COMP_SIGB | +IEEE80211_HE_PHY_CAP9_RX_FULL_BW_SU_USING_MU_WITH_NON_COMP_SIGB ); +break ; } he_cap->he_mcs_nss_supp.rx_mcs_80 =
Signature · 1 line
2.20.1
Re: [RFC PATCH v2 3/3] ath11k: register HE mesh capabilities
On Tuesday, 11 June 2019 20:02:47 CEST Sven Eckelmann wrote:
[...]
Quoted 3 lines
---
This doesn't work currently as expected. No HE rates are used between the two HE mesh peers:
[...]
There seems to be also an ordering problem. ath11k_peer_assoc_h_he is only called before ieee80211_he_cap_ie_to_sta_he_cap is called. So ath11k_bss_assoc will not have the information whether the remote has HE support or not.
Looks like I have adjust mesh_sta_info_init to get this somehow to ath11k_peer_assoc_h_he. Maybe through ath11k_sta_rc_update but this is not called by mesh_sta_info_init at the moment. Just because rate_control_rate_init is called and not rate_control_rate_update.
The easiest method seems to adjust the check at the end of mesh_sta_info_init to
if (!test_sta_flag(sta, WLAN_STA_RATE_CONTROL) &&
!ieee80211_hw_check(&local->hw, HAS_RATE_CONTROL)) {
rate_control_rate_init(sta);
} else {
rate_control_rate_update(local, sband, sta, changed);
}and to create a IEEE80211_RC_SUPP_RATES_CHANGED change when the has_he state changes. And yes, I know that Bob Copeland added this because it would have crashed ath10k when rate_control_rate_init is not used [1]. The other suggestion would be:
if (!test_sta_flag(sta, WLAN_STA_RATE_CONTROL)) rate_control_rate_init(sta);
/* inform drivers about changes */
rate_control_rate_update(local, sband, sta, changed);
Both will at least cause a call to ath11k_peer_assoc_prepare + ath11k_wmi_send_peer_assoc_cmd but unfortunately the ath11k firmware hangs afterwards.
Kind regards,
Sven
_______________________________________________
ath11k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath11k
Re: [RFC PATCH v2 3/3] ath11k: register HE mesh capabilities
On Tuesday, 11 June 2019 21:52:20 CEST Sven Eckelmann wrote:
[...]
Quoted 9 lines
if (!test_sta_flag(sta, WLAN_STA_RATE_CONTROL)) rate_control_rate_init(sta);/* inform drivers about changes */ rate_control_rate_update(local, sband, sta, changed);Both will at least cause a call to
ath11k_peer_assoc_prepare+ath11k_wmi_send_peer_assoc_cmdbut unfortunately the ath11k firmware hangs afterwards.
The fw hang seems to be related to the not set bss_conf.he_support in ath11k_mac_vdev_start_restart. This has to be set when ieee80211_join_mesh calls ieee80211_vif_use_channel. Otherwise the firmware will set a HT/VHT mode in the firmware. Any sta with an higher phy mode will just hang the firmware.
So the two main problems right now are:
* set bss_conf.he_support during mesh_join before
ath11k_mac_vdev_start_restart is called
- no clue what the best approach is
* let ath11k redo the association procedure with he_cap->has_he set to true when wpa_supplicant is in control of the peers.
Kind regards,
Sven
Re: [RFC PATCH v2 3/3] ath11k: register HE mesh capabilities
In reply to Sven EckelmannQuoted 19 lines · Sven Eckelmann
On Tuesday, 11 June 2019 20:02:47 CEST Sven Eckelmann wrote:
[...]Quoted 3 lines
---
This doesn't work currently as expected. No HE rates are used between the two HE mesh peers:[...]
There seems to be also an ordering problem.
ath11k_peer_assoc_h_heis only called beforeieee80211_he_cap_ie_to_sta_he_capis called. Soath11k_bss_assocwill not have the information whether the remote has HE support or not.Looks like I have adjust
mesh_sta_info_initto get this somehow toath11k_peer_assoc_h_he. Maybe throughath11k_sta_rc_updatebut this is not called bymesh_sta_info_initat the moment. Just becauserate_control_rate_initis called and notrate_control_rate_update.The easiest method seems to adjust the check at the end of
mesh_sta_info_initto
Quoted 6 lines
if (!test_sta_flag(sta, WLAN_STA_RATE_CONTROL) &&
!ieee80211_hw_check(&local->hw, HAS_RATE_CONTROL)) {
rate_control_rate_init(sta);
} else {
rate_control_rate_update(local, sband, sta, changed);
}Maybe we should just do this?
net/mac80211/rate.c +2 -1
@@ -42,7 +42,7 @@ void rate_control_rate_init(struct sta_info *sta)ieee80211_sta_set_rx_nss (sta);if (!ref) -return ; + goto out;rcu_read_lock ();
@@ -59,6 +59,7 @@ void rate_control_rate_init(struct sta_info *sta) priv_sta);spin_unlock_bh (&sta->rate_ctrl_lock);rcu_read_unlock (); +out:set_sta_flag (sta,WLAN_STA_RATE_CONTROL ); }
That was my intent, anyway -- that NSS always got set before rate_control_rate_update() even if using HW rate control.
Quoted 9 lines
if (!test_sta_flag(sta, WLAN_STA_RATE_CONTROL)) rate_control_rate_init(sta);/* inform drivers about changes */ rate_control_rate_update(local, sband, sta, changed);Both will at least cause a call to
ath11k_peer_assoc_prepare+ath11k_wmi_send_peer_assoc_cmdbut unfortunately the ath11k firmware hangs afterwards.
I think this would be OK.
Signature · 1 line
Bob Copeland %% https://bobcopeland.com/