Skip to contentSkip to conversation

Add imx7d speed grading and higher OPPs

PATCH Applied Leonard Crestez 3 participants 8 messages Jun 5, 2019 – Jun 12, 2019

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

cover Add imx7d speed grading and higher OPPs

Changes since v1:
* Remove the match list from imx-cpufreq-dt
* Split arch and cpufreq changes
Link to v1: https://patchwork.kernel.org/project/linux-arm-kernel/list/?series=124427

Leonard Crestez (5):
cpufreq: imx-cpufreq-dt: Remove global platform match list
cpufreq: Switch imx7d to imx-cpufreq-dt for speed grading
ARM: imx: Switch imx7d to imx-cpufreq-dt for speed-grading
ARM: dts: imx7d: Update cpufreq OPP table
ARM: imx_v6_v7_defconfig: Enable CONFIG_ARM_IMX_CPUFREQ_DT

 arch/arm/boot/dts/imx7d.dtsi         | 16 +++++++++++++---
 arch/arm/boot/dts/imx7s.dtsi         |  4 ++++
 arch/arm/configs/imx_v6_v7_defconfig |  1 +
 arch/arm/mach-imx/mach-imx7d.c       |  7 +++++++
 drivers/cpufreq/cpufreq-dt-platdev.c |  2 +-
 drivers/cpufreq/imx-cpufreq-dt.c     | 18 ++----------------
 6 files changed, 28 insertions(+), 20 deletions(-)
Signature · 1 line
2.7.4
#1 lore raw

PATCH v2 1/5 cpufreq: imx-cpufreq-dt: Remove global platform match list

This is not currently needed, instead a platform device is always created from SOC-specific code.

We can use of_machine_is_compatible for per-SOC behavior instead.

---
 drivers/cpufreq/imx-cpufreq-dt.c | 18 ++----------------
 1 file changed, 2 insertions(+), 16 deletions(-)
drivers/cpufreq/imx-cpufreq-dt.c +2 -16
index 35b6717d7255..b54fd26ea7df 100644
@@ -17,35 +17,21 @@
 #define OCOTP_CFG3_SPEED_GRADE_SHIFT	8
 #define OCOTP_CFG3_SPEED_GRADE_MASK	(0x3 << 8)
 #define OCOTP_CFG3_MKT_SEGMENT_SHIFT    6
 #define OCOTP_CFG3_MKT_SEGMENT_MASK     (0x3 << 6)
 
-static const struct of_device_id imx_cpufreq_dt_match_list[] = {
-	{ .compatible = "fsl,imx8mm" },
-	{ .compatible = "fsl,imx8mq" },
-	{}
-};
-
 /* cpufreq-dt device registered by imx-cpufreq-dt */
 static struct platform_device *cpufreq_dt_pdev;
 static struct opp_table *cpufreq_opp_table;
 
 static int imx_cpufreq_dt_probe(struct platform_device *pdev)
 {
 	struct device *cpu_dev = get_cpu_device(0);
-	struct device_node *np;
-	const struct of_device_id *match;
 	u32 cell_value, supported_hw[2];
 	int speed_grade, mkt_segment;
 	int ret;
 
-	np = of_find_node_by_path("/");
-	match = of_match_node(imx_cpufreq_dt_match_list, np);
-	of_node_put(np);
-	if (!match)
-		return -ENODEV;
-
 	ret = nvmem_cell_read_u32(cpu_dev, "speed_grade", &cell_value);
 	if (ret)
 		return ret;
 
 	speed_grade = (cell_value & OCOTP_CFG3_SPEED_GRADE_MASK) >> OCOTP_CFG3_SPEED_GRADE_SHIFT;
@@ -59,12 +45,12 @@ static int imx_cpufreq_dt_probe(struct platform_device *pdev)
 	 * consumer parts so clamp to 1 to avoid warning for "no OPPs"
 	 *
 	 * Applies to 8mq and 8mm.
 	 */
 	if (mkt_segment == 0 && speed_grade == 0 && (
-			!strcmp(match->compatible, "fsl,imx8mm") ||
-			!strcmp(match->compatible, "fsl,imx8mq")))
+			of_machine_is_compatible("fsl,imx8mm") ||
+			of_machine_is_compatible("fsl,imx8mq")))
 		speed_grade = 1;
 
 	supported_hw[0] = BIT(speed_grade);
 	supported_hw[1] = BIT(mkt_segment);
 	dev_info(&pdev->dev, "cpu speed grade %d mkt segment %d supported-hw %#x %#x\n",
Signature · 1 line
2.7.4
#2 lore raw

PATCH v2 2/5 cpufreq: Switch imx7d to imx-cpufreq-dt for speed grading

In reply to Leonard Crestez

This driver can handle speed grading bits on imx7d just like on imx8mq and imx8mm.

---
 drivers/cpufreq/cpufreq-dt-platdev.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/cpufreq/cpufreq-dt-platdev.c +1 -1
index 19c1aad57e26..eb282dff9f2c 100644
@@ -38,11 +38,10 @@ static const struct of_device_id whitelist[] __initconst = {
 	{ .compatible = "hisilicon,hi3660", },
 
 	{ .compatible = "fsl,imx27", },
 	{ .compatible = "fsl,imx51", },
 	{ .compatible = "fsl,imx53", },
-	{ .compatible = "fsl,imx7d", },
 
 	{ .compatible = "marvell,berlin", },
 	{ .compatible = "marvell,pxa250", },
 	{ .compatible = "marvell,pxa270", },
 
@@ -106,10 +105,11 @@ static const struct of_device_id whitelist[] __initconst = {
  */
 static const struct of_device_id blacklist[] __initconst = {
 	{ .compatible = "calxeda,highbank", },
 	{ .compatible = "calxeda,ecx-2000", },
 
+	{ .compatible = "fsl,imx7d", },
 	{ .compatible = "fsl,imx8mq", },
 	{ .compatible = "fsl,imx8mm", },
 
 	{ .compatible = "marvell,armadaxp", },
 
Signature · 1 line
2.7.4
#3 lore raw

PATCH v2 3/5 ARM: imx: Switch imx7d to imx-cpufreq-dt for speed-grading

In reply to Leonard Crestez

The imx-cpufreq-dt driver can handle speed grading bits on imx7d just like on imx8mq and imx8mm.

---
 arch/arm/mach-imx/mach-imx7d.c | 7 +++++++
 1 file changed, 7 insertions(+)
arch/arm/mach-imx/mach-imx7d.c +7 -0
index 26ca744d3e2b..0b77412795c9 100644
@@ -95,10 +95,16 @@ static void __init imx7d_init_machine(void)
 
 	imx_anatop_init();
 	imx7d_enet_init();
 }
 
+static void __init imx7d_init_late(void)
+{
+	if (IS_ENABLED(CONFIG_ARM_IMX_CPUFREQ_DT))
+		platform_device_register_simple("imx-cpufreq-dt", -1, NULL, 0);
+}
+
 static void __init imx7d_init_irq(void)
 {
 	imx_init_revision_from_anatop();
 	imx_src_init();
 	irqchip_init();
@@ -111,7 +117,8 @@ static const char *const imx7d_dt_compat[] __initconst = {
 };
 
 DT_MACHINE_START(IMX7D, "Freescale i.MX7 Dual (Device Tree)")
 	.init_irq	= imx7d_init_irq,
 	.init_machine	= imx7d_init_machine,
+	.init_late      = imx7d_init_late,
 	.dt_compat	= imx7d_dt_compat,
 MACHINE_END
Signature · 1 line
2.7.4
#4 lore raw

PATCH v2 4/5 ARM: dts: imx7d: Update cpufreq OPP table

In reply to Leonard Crestez

According to latest docs imx7d chips can go from 800 to 1200 mhz. Maximum frequency is determined from two speed grading bits present in OCOTP fuses at same location as other imx chips.

Also update to "typical" voltages from latest datasheet, 25mv higher than current dts.

All imx7s parts are still fixed at 800mhz

Based on:
* IMX7DCEC Rev. 6, 03/2019
* IMX7SCEC Rev. 6, 03/2019
* IMX7DRM Rev. 1, 01/2018 Page 1102

---
 arch/arm/boot/dts/imx7d.dtsi | 16 +++++++++++++---
 arch/arm/boot/dts/imx7s.dtsi |  4 ++++
 2 files changed, 17 insertions(+), 3 deletions(-)
arch/arm/boot/dts/imx7d.dtsi +13 -3
index f33b560821b8..42528d2812a2 100644
@@ -10,10 +10,12 @@
 	cpus {
 		cpu0: cpu@0 {
 			clock-frequency = <996000000>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			#cooling-cells = <2>;
+			nvmem-cells = <&cpu_speed_grade>;
+			nvmem-cell-names = "speed_grade";
 		};
 
 		cpu1: cpu@1 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
@@ -37,19 +39,27 @@
 		compatible = "operating-points-v2";
 		opp-shared;
 
 		opp-792000000 {
 			opp-hz = /bits/ 64 <792000000>;
-			opp-microvolt = <975000>;
+			opp-microvolt = <1000000>;
 			clock-latency-ns = <150000>;
+			opp-supported-hw = <0xf>, <0xf>;
 		};
 
 		opp-996000000 {
 			opp-hz = /bits/ 64 <996000000>;
-			opp-microvolt = <1075000>;
+			opp-microvolt = <1100000>;
 			clock-latency-ns = <150000>;
-			opp-suspend;
+			opp-supported-hw = <0xc>, <0xf>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1225000>;
+			clock-latency-ns = <150000>;
+			opp-supported-hw = <0x8>, <0xf>;
 		};
 	};
 
 	usbphynop2: usbphynop2 {
 		compatible = "usb-nop-xceiv";
arch/arm/boot/dts/imx7s.dtsi +4 -0
index d8b4eb67146d..5b8292670b4b 100644
@@ -549,10 +549,14 @@
 				};
 
 				tempmon_temp_grade: temp-grade@10 {
 					reg = <0x10 0x4>;
 				};
+
+				cpu_speed_grade: speed-grade@10 {
+					reg = <0x10 0x4>;
+				};
 			};
 
 			anatop: anatop@30360000 {
 				compatible = "fsl,imx7d-anatop", "fsl,imx6q-anatop",
 					"syscon", "simple-bus";
Signature · 1 line
2.7.4
#5 lore raw

PATCH v2 5/5 ARM: imx_v6_v7_defconfig: Enable CONFIG_ARM_IMX_CPUFREQ_DT

In reply to Leonard Crestez

This is used for imx7d speed grading.

---
 arch/arm/configs/imx_v6_v7_defconfig | 1 +
 1 file changed, 1 insertion(+)
arch/arm/configs/imx_v6_v7_defconfig +1 -0
index 4daf807e6970..507c1fcca624 100644
@@ -52,10 +52,11 @@ CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
 CONFIG_CPU_FREQ_GOV_POWERSAVE=y
 CONFIG_CPU_FREQ_GOV_USERSPACE=y
 CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
 CONFIG_CPUFREQ_DT=y
 CONFIG_ARM_IMX6Q_CPUFREQ=y
+CONFIG_ARM_IMX_CPUFREQ_DT=y
 CONFIG_CPU_IDLE=y
 CONFIG_ARM_CPUIDLE=y
 CONFIG_VFP=y
 CONFIG_NEON=y
 CONFIG_PM_DEBUG=y
Signature · 1 line
2.7.4
maintainer
#6 lore raw
In reply to Leonard Crestez
Quoted 7 lines · Leonard Crestez

Changes since v1:
* Remove the match list from imx-cpufreq-dt
* Split arch and cpufreq changes
Link to v1: https://patchwork.kernel.org/project/linux-arm-kernel/list/?series=124427

Leonard Crestez (5):
cpufreq: imx-cpufreq-dt: Remove global platform match list

Added following to this patch:

Quoted 1 line

cpufreq: Switch imx7d to imx-cpufreq-dt for speed grading

Applied the first two patches. Thanks.

Signature · 1 line
viresh
Applied
#7 lore raw
In reply to Leonard Crestez
Quoted 5 lines · Leonard Crestez

Changes since v1:
* Remove the match list from imx-cpufreq-dt
* Split arch and cpufreq changes
Link to v1: https://patchwork.kernel.org/project/linux-arm-kernel/list/?series=124427

Quoted 7 lines

Leonard Crestez (5):
cpufreq: imx-cpufreq-dt: Remove global platform match list
cpufreq: Switch imx7d to imx-cpufreq-dt for speed grading

ARM: imx: Switch imx7d to imx-cpufreq-dt for speed-grading
ARM: dts: imx7d: Update cpufreq OPP table
ARM: imx_v6_v7_defconfig: Enable CONFIG_ARM_IMX_CPUFREQ_DT

Applied these 3, thanks.