ipv4: Support multipath hashing on inner IP pkts for GRE tunnel
Subsystems (4)
PATCH v2 1/1 ipv4: Support multipath hashing on inner IP pkts for GRE tunnel
Multipath hash policy value of 0 isn't distributing since the outer IP dest and src aren't varied eventhough the inner ones are. Since the flow is on the inner ones in the case of tunneled traffic, hashing on them is desired.
This is done mainly for IP over GRE, hence only tested for that. But anything else supported by flow dissection should work.
v2: Use skb_flow_dissect_flow_keys() directly so that other tunneling
can be supported through flow dissection (per Nikolay Aleksandrov).
--- Documentation/networking/ip-sysctl.txt | 1 + net/ipv4/route.c | 20 ++++++++++++++++++++ net/ipv4/sysctl_net_ipv4.c | 2 +- 3 files changed, 22 insertions(+), 1 deletion(-)
Documentation/networking/ip-sysctl.txt +1 -0
@@ -80,6 +80,7 @@ fib_multipath_hash_policy - INTEGER Possible values: 0 - Layer 3 1 - Layer 4 + 2 - Inner Layer 3 for tunneled IP packets. fib_sync_mem - UNSIGNED INTEGER Amount of dirty memory from fib entries that can be backlogged before
net/ipv4/route.c +20 -0
@@ -1872,6 +1872,26 @@ int fib_multipath_hash(const struct net *net, const struct flowi4 *fl4, hash_keys.basic.ip_proto = fl4->flowi4_proto; }break ; +case 2 : +memset (&hash_keys,0 ,sizeof (hash_keys)); + hash_keys.control.addr_type =FLOW_DISSECTOR_KEY_IPV4_ADDRS ; +/* skb is currently provided only when forwarding */ +if (skb) { +struct flow_keys keys; + +skb_flow_dissect_flow_keys (skb, &keys,0 ); + + hash_keys.addrs.v4addrs.src = keys.addrs.v4addrs.src; + hash_keys.addrs.v4addrs.dst = keys.addrs.v4addrs.dst; + hash_keys.ports.src = keys.ports.src; + hash_keys.ports.dst = keys.ports.dst; + hash_keys.basic.ip_proto = keys.basic.ip_proto; + }else { +/* Same as case 0 */ + hash_keys.addrs.v4addrs.src = fl4->saddr; + hash_keys.addrs.v4addrs.dst = fl4->daddr; + } +break ; } mhash =flow_hash_from_keys (&hash_keys);
net/ipv4/sysctl_net_ipv4.c +1 -1
@@ -960,7 +960,7 @@ static struct ctl_table ipv4_net_table[] = { .mode = 0644, .proc_handler = proc_fib_multipath_hash_policy, .extra1 = &zero, - .extra2 = &one, + .extra2 = &two, },#endif {
Signature · 1 line
2.17.1
Quoted 22 lines · Stephen Suryaputra
Multipath hash policy value of 0 isn't distributing since the outer IP dest and src aren't varied eventhough the inner ones are. Since the flow is on the inner ones in the case of tunneled traffic, hashing on them is desired.
This is done mainly for IP over GRE, hence only tested for that. But anything else supported by flow dissection should work.
v2: Use
skb_flow_dissect_flow_keys()directly so that other tunneling
can be supported through flow dissection (per Nikolay Aleksandrov).Signed-off-by Stephen Suryaputra <[email protected]>--- Documentation/networking/ip-sysctl.txt | 1 + net/ipv4/route.c | 20 ++++++++++++++++++++ net/ipv4/sysctl_net_ipv4.c | 2 +- 3 files changed, 22 insertions(+), 1 deletion(-)Documentation/networking/ip-sysctl.txt +0
-0
Documentation/networking/ip-sysctl.txt fib_multipath_hash_policy - INTEGER · line 83
Quoted 4 lines
Documentation/networking/ip-sysctl.txt +1
-0@@ -80,6 +80,7 @@ fib_multipath_hash_policy - INTEGER Possible values: 0 - Layer 3 1 - Layer 4 + 2 - Inner Layer 3 for tunneled IP packets.
Hmm, but you're using the ports below, so it's not L3 ?
Quoted 15 lines
Documentation/networking/ip-sysctl.txt +0
-0fib_sync_mem - UNSIGNED INTEGER Amount of dirty memory from fib entries that can be backlogged beforenet/ipv4/route.c +4
-0@@ -1872,6 +1872,26 @@ int fib_multipath_hash(const struct net *net, const struct flowi4 *fl4, hash_keys.basic.ip_proto = fl4->flowi4_proto; }break ; +case 2 : +memset (&hash_keys,0 ,sizeof (hash_keys)); + hash_keys.control.addr_type =FLOW_DISSECTOR_KEY_IPV4_ADDRS ; +/* skb is currently provided only when forwarding */
net/ipv4/route.c int fib_multipath_hash(const struct net *net, const struct flowi4 *fl4, · line 1888
Quoted 10 lines
net/ipv4/route.c +10
-0+if (skb) { +struct flow_keys keys; + +skb_flow_dissect_flow_keys (skb, &keys,0 ); + + hash_keys.addrs.v4addrs.src = keys.addrs.v4addrs.src; + hash_keys.addrs.v4addrs.dst = keys.addrs.v4addrs.dst; + hash_keys.ports.src = keys.ports.src; + hash_keys.ports.dst = keys.ports.dst; + hash_keys.basic.ip_proto = keys.basic.ip_proto;
This is inconsistent with the code below, you're using ports when we have skb and using only addresses when we don't (host traffic). So either make it L3-only and use addresses or make sure you're using the correct ports as well.
Quoted 23 lines
net/ipv4/route.c +6
-0+ }else { +/* Same as case 0 */ + hash_keys.addrs.v4addrs.src = fl4->saddr; + hash_keys.addrs.v4addrs.dst = fl4->daddr; + } +break ; } mhash =flow_hash_from_keys (&hash_keys);net/ipv4/sysctl_net_ipv4.c +1
-1@@ -960,7 +960,7 @@ static struct ctl_table ipv4_net_table[] = { .mode = 0644, .proc_handler = proc_fib_multipath_hash_policy, .extra1 = &zero, - .extra2 = &one, + .extra2 = &two, },#endif {