Skip to contentSkip to conversation

arm64: tegra: Add INA3221 channel info for Jetson TX2

PATCH Applied Nicolin Chen 2 participants 2 messages Jun 17, 2019 – Jun 18, 2019

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 arm64: tegra: Add INA3221 channel info for Jetson TX2

There are four INA3221 chips on the Jetson TX2 (p3310 + p2771). And each INA3221 chip has three input channels to monitor power.

So this patch adds these 12 channels to the DT of Jetson TX2, by following the DT binding of INA3221 and official documents from
https://developer.nvidia.com/embedded/downloads

tegra186-p3310:
https://developer.nvidia.com/embedded/dlc/jetson-tx2-series-modules-oem-product-design-guide

tegra186-p2771-0000:
http://developer.nvidia.com/embedded/dlc/jetson-tx1-tx2-developer-kit-carrier-board-spec-20180618

---
 .../boot/dts/nvidia/tegra186-p2771-0000.dts   | 40 +++++++++++++++++++
 .../arm64/boot/dts/nvidia/tegra186-p3310.dtsi | 40 +++++++++++++++++++
 2 files changed, 80 insertions(+)
arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts +40 -0
index ab6648c72ad5..9df4782c90f3 100644
@@ -14,11 +14,51 @@
 		power-monitor@42 {
 			compatible = "ti,ina3221";
 			reg = <0x42>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				reg = <0x0>;
+				label = "VDD_MUX";
+				shunt-resistor-micro-ohms = <20000>;
+			};
+
+			channel@1 {
+				reg = <0x1>;
+				label = "VDD_5V0_IO_SYS";
+				shunt-resistor-micro-ohms = <5000>;
+			};
+
+			channel@2 {
+				reg = <0x2>;
+				label = "VDD_3V3_SYS";
+				shunt-resistor-micro-ohms = <10000>;
+			};
 		};
 
 		power-monitor@43 {
 			compatible = "ti,ina3221";
 			reg = <0x43>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				reg = <0x0>;
+				label = "VDD_3V3_IO_SLP";
+				shunt-resistor-micro-ohms = <10000>;
+			};
+
+			channel@1 {
+				reg = <0x1>;
+				label = "VDD_1V8_IO";
+				shunt-resistor-micro-ohms = <10000>;
+			};
+
+			channel@2 {
+				reg = <0x2>;
+				label = "VDD_M2_IN";
+				shunt-resistor-micro-ohms = <10000>;
+			};
 		};
 
 		exp1: gpio@74 {
arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi +40 -0
index 4bbee83d9943..5e18acf5cfad 100644
@@ -67,11 +67,51 @@
 		power-monitor@40 {
 			compatible = "ti,ina3221";
 			reg = <0x40>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				reg = <0x0>;
+				label = "VDD_SYS_GPU";
+				shunt-resistor-micro-ohms = <10000>;
+			};
+
+			channel@1 {
+				reg = <0x1>;
+				label = "VDD_SYS_SOC";
+				shunt-resistor-micro-ohms = <10000>;
+			};
+
+			channel@2 {
+				reg = <0x2>;
+				label = "VDD_3V8_WIFI";
+				shunt-resistor-micro-ohms = <10000>;
+			};
 		};
 
 		power-monitor@41 {
 			compatible = "ti,ina3221";
 			reg = <0x41>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				reg = <0x0>;
+				label = "VDD_IN";
+				shunt-resistor-micro-ohms = <5000>;
+			};
+
+			channel@1 {
+				reg = <0x1>;
+				label = "VDD_SYS_CPU";
+				shunt-resistor-micro-ohms = <10000>;
+			};
+
+			channel@2 {
+				reg = <0x2>;
+				label = "VDD_5V0_DDR";
+				shunt-resistor-micro-ohms = <10000>;
+			};
 		};
 	};
 
Signature · 1 line
2.17.1
#1 lore raw
Quoted 10 lines · Nicolin Chen

There are four INA3221 chips on the Jetson TX2 (p3310 + p2771). And each INA3221 chip has three input channels to monitor power.

So this patch adds these 12 channels to the DT of Jetson TX2, by following the DT binding of INA3221 and official documents from
https://developer.nvidia.com/embedded/downloads

tegra186-p3310:
https://developer.nvidia.com/embedded/dlc/jetson-tx2-series-modules-oem-product-design-guide

Quoted 8 lines

tegra186-p2771-0000:
http://developer.nvidia.com/embedded/dlc/jetson-tx1-tx2-developer-kit-carrier-board-spec-20180618

---
 .../boot/dts/nvidia/tegra186-p2771-0000.dts   | 40 +++++++++++++++++++
 .../arm64/boot/dts/nvidia/tegra186-p3310.dtsi | 40 +++++++++++++++++++
 2 files changed, 80 insertions(+)

Applied, thanks.

Thierry