ARM: imx: dh-imx6: Enable DM regulator
PATCH v2 1/1 ARM: imx: dh-imx6: Enable DM regulator
Enable DM support for regulators and fixed regulator driver and convert USB Vbus control over to the regulators defined in DT.
---
V2: Fix subject, should read DM regulator instead of DM GPIO
--- board/dhelectronics/dh_imx6/dh_imx6.c | 17 ----------------- configs/dh_imx6_defconfig | 2 ++ 2 files changed, 2 insertions(+), 17 deletions(-)
board/dhelectronics/dh_imx6/dh_imx6.c +0 -17
@@ -196,7 +196,6 @@ int board_eth_init(bd_t *bis)#ifdef CONFIG_USB_EHCI_MX6 static void setup_usb (void ) { -gpio_request (IMX_GPIO_NR (3 ,31 ),"USB-VBUS" );/* * Set daisy chain for otg_pin_id on MX6Q. * For MX6DL, this bit is reserved.
@@ -211,22 +210,6 @@ int board_usb_phy_mode(int port) else return USB_INIT_DEVICE; } - -int board_ehci_power (int port,int on) -{ -switch (port) { -case 0 : -break ; -case 1 : -gpio_direction_output (IMX_GPIO_NR (3 ,31 ), !!on); -break ; -default : -printf ("MXC USB port %d not yet supported\n" , port); -return -EINVAL ; - } - -return 0 ; -}#endif static int setup_dhcom_mac_from_fuse (void )
configs/dh_imx6_defconfig +2 -0
@@ -64,6 +64,8 @@ CONFIG_FEC_MXC=y CONFIG_MII=y CONFIG_PINCTRL=y CONFIG_PINCTRL_IMX6=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y CONFIG_DM_SCSI=y CONFIG_SPI=y CONFIG_DM_SPI=y
Signature · 1 line
2.20.1
PATCH v2 1/1 ARM: imx: dh-imx6: Enable DM regulator
Marek Vasut <[email protected]> Friday 21st June 2019 0:51:
Quoted 65 lines
Enable DM support for regulators and fixed regulator driver and convert USB Vbus control over to the regulators defined in DT.
Signed-off-by Marek Vasut <[email protected]>Cc Ludwig Zenz <[email protected]>Cc Stefano Babic <[email protected]>---
V2: Fix subject, should read DM regulator instead of DM GPIO--- board/dhelectronics/dh_imx6/dh_imx6.c | 17 ----------------- configs/dh_imx6_defconfig | 2 ++ 2 files changed, 2 insertions(+), 17 deletions(-)board/dhelectronics/dh_imx6/dh_imx6.c +0
-17@@ -196,7 +196,6 @@ int board_eth_init(bd_t *bis)#ifdef CONFIG_USB_EHCI_MX6 static void setup_usb (void ) { -gpio_request (IMX_GPIO_NR (3 ,31 ),"USB-VBUS" );/* * Set daisy chain for otg_pin_id on MX6Q. * For MX6DL, this bit is reserved. @@ -211,22 +210,6 @@ int board_usb_phy_mode(int port) else return USB_INIT_DEVICE; } - -int board_ehci_power (int port,int on) -{ -switch (port) { -case 0 : -break ; -case 1 : -gpio_direction_output (IMX_GPIO_NR (3 ,31 ), !!on); -break ; -default : -printf ("MXC USB port %d not yet supported\n" , port); -return -EINVAL ; - } - -return 0 ; -}#endif static int setup_dhcom_mac_from_fuse (void )configs/dh_imx6_defconfig +2
-0@@ -64,6 +64,8 @@ CONFIG_FEC_MXC=y CONFIG_MII=y CONFIG_PINCTRL=y CONFIG_PINCTRL_IMX6=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y CONFIG_DM_SCSI=y CONFIG_SPI=y CONFIG_DM_SPI=ySignature · 1 line
2.20.1
Thanks,
Regards
PATCH v2 1/1 ARM: imx: dh-imx6: Enable DM regulator
In reply to Marek VasutQuoted 6 lines
Enable DM support for regulators and fixed regulator driver and convert USB Vbus control over to the regulators defined in DT.
Signed-off-by Marek Vasut <[email protected]>Cc Ludwig Zenz <[email protected]>Cc Stefano Babic <[email protected]>Tested-by Ludwig Zenz <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================