Skip to contentSkip to conversation

drm/panel-simple: Add panel parameters for ortustech-com37h3m05dtc/99dtc and sharp-lq070y3dg3b

PATCH In review H. Nikolaus Schaller 3 participants 21 messages Jun 7, 2019 – Jul 23, 2019

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

v3 cover drm/panel-simple: Add panel parameters for ortustech-com37h3m05dtc/99dtc and sharp-lq070y3dg3b

V3:
* add bindings documentation (suggested by [email protected])

V2 2019-06-05 07:07:05:
* fix typo in 99dtc panel compatible string (reported by [email protected])

V1 2019-06-04 14:53:00:

Since v5.2-rc1 OMAP is no longer using a special display driver architecture for DPI panels, but uses the general drm/panel/panel-simple.

So we finally can add SoC independent panel definitions for two panel models which we already had worked on quite a while ago (before device tree was introduced):

	https://patchwork.kernel.org/patch/2851295/

H. Nikolaus Schaller (5):
drm/panel: simple: Add Sharp LQ070Y3DG3B panel support drm/panel: simple: Add Ortustech COM37H3M panel support
dt-bindings: drm/panel: simple: add ortustech,com37h3m05dtc panel
dt-bindings: drm/panel: simple: add ortustech,com37h3m99dtc panel
dt-bindings: drm/panel: simple: add sharp,lq070y3dg3b panel

 .../display/panel/ortustech,com37h3m05dtc.txt | 12 ++++
 .../display/panel/ortustech,com37h3m99dtc.txt | 12 ++++
 .../display/panel/sharp,lq070y3dg3b.txt       | 12 ++++
 drivers/gpu/drm/panel/panel-simple.c          | 63 +++++++++++++++++++
 4 files changed, 99 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/ortustech,com37h3m05dtc.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/ortustech,com37h3m99dtc.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/sharp,lq070y3dg3b.txt
Signature · 1 line
2.19.1
#1 lore raw

PATCH v3 1/5 drm/panel: simple: Add Sharp LQ070Y3DG3B panel support

The change adds support for the Sharp LQ070Y3DG3B 7.0" TFT LCD panel.

Tested on Letux7004.

---
 drivers/gpu/drm/panel/panel-simple.c | 30 ++++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)
drivers/gpu/drm/panel/panel-simple.c +30 -0
index 569be4efd8d1..5b27829c5a78 100644
@@ -2204,6 +2204,33 @@ static const struct panel_desc samsung_ltn140at29_301 = {
 	},
 };
 
+static const struct drm_display_mode sharp_lq070y3dg3b_mode = {
+	.clock = 33260,
+	.hdisplay = 800,
+	.hsync_start = 800 + 64,
+	.hsync_end = 800 + 64 + 128,
+	.htotal = 800 + 64 + 128 + 64,
+	.vdisplay = 480,
+	.vsync_start = 480 + 8,
+	.vsync_end = 480 + 8 + 2,
+	.vtotal = 480 + 8 + 2 + 35,
+	.vrefresh = 60,
+	.flags = DISPLAY_FLAGS_PIXDATA_POSEDGE,
+};
+
+static const struct panel_desc sharp_lq070y3dg3b = {
+	.modes = &sharp_lq070y3dg3b_mode,
+	.num_modes = 1,
+	.bpc = 8,
+	.size = {
+		.width = 152,	/* 152.4mm */
+		.height = 91,	/* 91.4mm */
+	},
+	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_POSEDGE |
+		     DRM_BUS_FLAG_SYNC_DRIVE_POSEDGE,
+};
+
 static const struct drm_display_mode sharp_lq035q7db03_mode = {
 	.clock = 5500,
 	.hdisplay = 240,
@@ -2786,6 +2813,9 @@ static const struct of_device_id platform_of_match[] = {
 	}, {
 		.compatible = "sharp,lq035q7db03",
 		.data = &sharp_lq035q7db03,
+	}, {
+		.compatible = "sharp,lq070y3dg3b",
+		.data = &sharp_lq070y3dg3b,
 	}, {
 		.compatible = "sharp,lq101k1ly04",
 		.data = &sharp_lq101k1ly04,
Signature · 1 line
2.19.1
Reviewed-by on v3 1/5
#2 lore raw

Re: [PATCH v3 1/5] drm/panel: simple: Add Sharp LQ070Y3DG3B panel support

Quoted 5 lines · H. Nikolaus Schaller

The change adds support for the Sharp LQ070Y3DG3B 7.0" TFT LCD panel.

Tested on Letux7004.

Quoted 59 lines
---
 drivers/gpu/drm/panel/panel-simple.c | 30 ++++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)
drivers/gpu/drm/panel/panel-simple.c +30 -0
index 569be4efd8d1..5b27829c5a78 100644
@@ -2204,6 +2204,33 @@ static const struct panel_desc samsung_ltn140at29_301 = {
 	},
 };
 
+static const struct drm_display_mode sharp_lq070y3dg3b_mode = {
+	.clock = 33260,
+	.hdisplay = 800,
+	.hsync_start = 800 + 64,
+	.hsync_end = 800 + 64 + 128,
+	.htotal = 800 + 64 + 128 + 64,
+	.vdisplay = 480,
+	.vsync_start = 480 + 8,
+	.vsync_end = 480 + 8 + 2,
+	.vtotal = 480 + 8 + 2 + 35,
+	.vrefresh = 60,
+	.flags = DISPLAY_FLAGS_PIXDATA_POSEDGE,
+};
+
+static const struct panel_desc sharp_lq070y3dg3b = {
+	.modes = &sharp_lq070y3dg3b_mode,
+	.num_modes = 1,
+	.bpc = 8,
+	.size = {
+		.width = 152,	/* 152.4mm */
+		.height = 91,	/* 91.4mm */
+	},
+	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_POSEDGE |
+		     DRM_BUS_FLAG_SYNC_DRIVE_POSEDGE,
+};
+
 static const struct drm_display_mode sharp_lq035q7db03_mode = {
 	.clock = 5500,
 	.hdisplay = 240,
@@ -2786,6 +2813,9 @@ static const struct of_device_id platform_of_match[] = {
 	}, {
 		.compatible = "sharp,lq035q7db03",
 		.data = &sharp_lq035q7db03,
+	}, {
+		.compatible = "sharp,lq070y3dg3b",
+		.data = &sharp_lq070y3dg3b,
 	}, {
 		.compatible = "sharp,lq101k1ly04",
 		.data = &sharp_lq101k1ly04,
Signature · 6 lines
2.19.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

#3 lore raw

PATCH v3 2/5 drm/panel: simple: Add Ortustech COM37H3M panel support

In reply to H. Nikolaus Schaller

The change adds support for the Ortustech COM37H3M05DTC/99DTC 3.7" TFT LCD panel.

Tested on Letux3704.

---
 drivers/gpu/drm/panel/panel-simple.c | 33 ++++++++++++++++++++++++++++
 1 file changed, 33 insertions(+)
drivers/gpu/drm/panel/panel-simple.c +33 -0
index 5b27829c5a78..1fb74908a269 100644
@@ -2007,6 +2007,33 @@ static const struct panel_desc ontat_yx700wv03 = {
 	.bus_format = MEDIA_BUS_FMT_RGB666_1X18,
 };
 
+static const struct drm_display_mode ortustech_com37h3m_mode  = {
+	.clock = 22153,
+	.hdisplay = 480,
+	.hsync_start = 480 + 8,
+	.hsync_end = 480 + 8 + 10,
+	.htotal = 480 + 8 + 10 + 10,
+	.vdisplay = 640,
+	.vsync_start = 640 + 4,
+	.vsync_end = 640 + 4 + 3,
+	.vtotal = 640 + 4 + 3 + 4,
+	.vrefresh = 60,
+	.flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
+};
+
+static const struct panel_desc ortustech_com37h3m = {
+	.modes = &ortustech_com37h3m_mode,
+	.num_modes = 1,
+	.bpc = 8,
+	.size = {
+		.width = 56,	/* 56.16mm */
+		.height = 75,	/* 74.88mm */
+	},
+	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_POSEDGE |
+		     DRM_BUS_FLAG_SYNC_DRIVE_POSEDGE,
+};
+
 static const struct drm_display_mode ortustech_com43h4m85ulc_mode  = {
 	.clock = 25000,
 	.hdisplay = 480,
@@ -2786,6 +2813,12 @@ static const struct of_device_id platform_of_match[] = {
 	}, {
 		.compatible = "ontat,yx700wv03",
 		.data = &ontat_yx700wv03,
+	}, {
+		.compatible = "ortustech,com37h3m05dtc",
+		.data = &ortustech_com37h3m,
+	}, {
+		.compatible = "ortustech,com37h3m99dtc",
+		.data = &ortustech_com37h3m,
 	}, {
 		.compatible = "ortustech,com43h4m85ulc",
 		.data = &ortustech_com43h4m85ulc,
Signature · 1 line
2.19.1
Reviewed-by on v3 2/5
#4 lore raw

Re: [PATCH v3 2/5] drm/panel: simple: Add Ortustech COM37H3M panel support

Quoted 5 lines · H. Nikolaus Schaller

The change adds support for the Ortustech COM37H3M05DTC/99DTC 3.7" TFT LCD panel.

Tested on Letux3704.

Quoted 62 lines
---
 drivers/gpu/drm/panel/panel-simple.c | 33 ++++++++++++++++++++++++++++
 1 file changed, 33 insertions(+)
drivers/gpu/drm/panel/panel-simple.c +33 -0
index 5b27829c5a78..1fb74908a269 100644
@@ -2007,6 +2007,33 @@ static const struct panel_desc ontat_yx700wv03 = {
 	.bus_format = MEDIA_BUS_FMT_RGB666_1X18,
 };
 
+static const struct drm_display_mode ortustech_com37h3m_mode  = {
+	.clock = 22153,
+	.hdisplay = 480,
+	.hsync_start = 480 + 8,
+	.hsync_end = 480 + 8 + 10,
+	.htotal = 480 + 8 + 10 + 10,
+	.vdisplay = 640,
+	.vsync_start = 640 + 4,
+	.vsync_end = 640 + 4 + 3,
+	.vtotal = 640 + 4 + 3 + 4,
+	.vrefresh = 60,
+	.flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
+};
+
+static const struct panel_desc ortustech_com37h3m = {
+	.modes = &ortustech_com37h3m_mode,
+	.num_modes = 1,
+	.bpc = 8,
+	.size = {
+		.width = 56,	/* 56.16mm */
+		.height = 75,	/* 74.88mm */
+	},
+	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_POSEDGE |
+		     DRM_BUS_FLAG_SYNC_DRIVE_POSEDGE,
+};
+
 static const struct drm_display_mode ortustech_com43h4m85ulc_mode  = {
 	.clock = 25000,
 	.hdisplay = 480,
@@ -2786,6 +2813,12 @@ static const struct of_device_id platform_of_match[] = {
 	}, {
 		.compatible = "ontat,yx700wv03",
 		.data = &ontat_yx700wv03,
+	}, {
+		.compatible = "ortustech,com37h3m05dtc",
+		.data = &ortustech_com37h3m,
+	}, {
+		.compatible = "ortustech,com37h3m99dtc",
+		.data = &ortustech_com37h3m,
 	}, {
 		.compatible = "ortustech,com43h4m85ulc",
 		.data = &ortustech_com43h4m85ulc,
Signature · 6 lines
2.19.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#5 lore raw

PATCH v3 3/5 dt-bindings: drm/panel: simple: add ortustech,com37h3m05dtc panel

In reply to H. Nikolaus Schaller
---
 .../display/panel/ortustech,com37h3m05dtc.txt        | 12 ++++++++++++
 1 file changed, 12 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/ortustech,com37h3m05dtc.txt
Documentation/devicetree/bindings/display/panel/ortustech,com37h3m05dtc.txt new file +12 -0
new file mode 100644
index 000000000000..c16907c02f80
@@ -0,0 +1,12 @@
+OrtusTech COM37H3M05DTC Blanview 3.7" VGA portrait TFT-LCD panel
+
+Required properties:
+- compatible: should be "ortustech,com37h3m05dtc"
+
+Optional properties:
+- enable-gpios: GPIO pin to enable or disable the panel
+- backlight: phandle of the backlight device attached to the panel
+- power-supply: phandle of the regulator that provides the supply voltage
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
Signature · 1 line
2.19.1
Reviewed-by on v3 3/5
#6 lore raw

Re: [PATCH v3 3/5] dt-bindings: drm/panel: simple: add ortustech, com37h3m05dtc panel

Quoted 1 line · H. Nikolaus Schaller

We need OK from one of the DT people before we can apply this.

Sam

Quoted 30 lines
---
 .../display/panel/ortustech,com37h3m05dtc.txt        | 12 ++++++++++++
 1 file changed, 12 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/ortustech,com37h3m05dtc.txt
Documentation/devicetree/bindings/display/panel/ortustech,com37h3m05dtc.txt new file +12 -0
new file mode 100644
index 000000000000..c16907c02f80
@@ -0,0 +1,12 @@
+OrtusTech COM37H3M05DTC Blanview 3.7" VGA portrait TFT-LCD panel
+
+Required properties:
+- compatible: should be "ortustech,com37h3m05dtc"
+
+Optional properties:
+- enable-gpios: GPIO pin to enable or disable the panel
+- backlight: phandle of the backlight device attached to the panel
+- power-supply: phandle of the regulator that provides the supply voltage
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
Signature · 6 lines
2.19.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
maintainer Reviewed-by on v3 3/5
#7 lore raw

Re: [PATCH v3 3/5] dt-bindings: drm/panel: simple: add ortustech,com37h3m05dtc panel

In reply to H. Nikolaus Schaller
Quoted 6 lines · H. Nikolaus Schaller
---
 .../display/panel/ortustech,com37h3m05dtc.txt        | 12 ++++++++++++
 1 file changed, 12 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/ortustech,com37h3m05dtc.txt
#8 lore raw

PATCH v3 4/5 dt-bindings: drm/panel: simple: add ortustech,com37h3m99dtc panel

In reply to H. Nikolaus Schaller
---
 .../display/panel/ortustech,com37h3m99dtc.txt        | 12 ++++++++++++
 1 file changed, 12 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/ortustech,com37h3m99dtc.txt
Documentation/devicetree/bindings/display/panel/ortustech,com37h3m99dtc.txt new file +12 -0
new file mode 100644
index 000000000000..06a73c3f46b5
@@ -0,0 +1,12 @@
+OrtusTech COM37H3M99DTC Blanview 3.7" VGA portrait TFT-LCD panel
+
+Required properties:
+- compatible: should be "ortustech,com37h3m99dtc"
+
+Optional properties:
+- enable-gpios: GPIO pin to enable or disable the panel
+- backlight: phandle of the backlight device attached to the panel
+- power-supply: phandle of the regulator that provides the supply voltage
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
Signature · 1 line
2.19.1
Reviewed-by on v3 4/5
#9 lore raw

Re: [PATCH v3 4/5] dt-bindings: drm/panel: simple: add ortustech, com37h3m99dtc panel

Quoted 1 line · H. Nikolaus Schaller
Quoted 30 lines
---
 .../display/panel/ortustech,com37h3m99dtc.txt        | 12 ++++++++++++
 1 file changed, 12 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/ortustech,com37h3m99dtc.txt
Documentation/devicetree/bindings/display/panel/ortustech,com37h3m99dtc.txt new file +12 -0
new file mode 100644
index 000000000000..06a73c3f46b5
@@ -0,0 +1,12 @@
+OrtusTech COM37H3M99DTC Blanview 3.7" VGA portrait TFT-LCD panel
+
+Required properties:
+- compatible: should be "ortustech,com37h3m99dtc"
+
+Optional properties:
+- enable-gpios: GPIO pin to enable or disable the panel
+- backlight: phandle of the backlight device attached to the panel
+- power-supply: phandle of the regulator that provides the supply voltage
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
Signature · 6 lines
2.19.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

maintainer Reviewed-by on v3 4/5
#10 lore raw

Re: [PATCH v3 4/5] dt-bindings: drm/panel: simple: add ortustech,com37h3m99dtc panel

In reply to H. Nikolaus Schaller
Quoted 6 lines · H. Nikolaus Schaller
---
 .../display/panel/ortustech,com37h3m99dtc.txt        | 12 ++++++++++++
 1 file changed, 12 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/ortustech,com37h3m99dtc.txt
#11 lore raw

PATCH v3 5/5 dt-bindings: drm/panel: simple: add sharp,lq070y3dg3b panel

In reply to H. Nikolaus Schaller
---
 .../bindings/display/panel/sharp,lq070y3dg3b.txt     | 12 ++++++++++++
 1 file changed, 12 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/sharp,lq070y3dg3b.txt
Documentation/devicetree/bindings/display/panel/sharp,lq070y3dg3b.txt new file +12 -0
new file mode 100644
index 000000000000..95534b55ee5f
@@ -0,0 +1,12 @@
+Sharp LQ070Y3DG3B 7.0" WVGA landscape TFT LCD panel
+
+Required properties:
+- compatible: should be "sharp,lq070y3dg3b"
+
+Optional properties:
+- enable-gpios: GPIO pin to enable or disable the panel
+- backlight: phandle of the backlight device attached to the panel
+- power-supply: phandle of the regulator that provides the supply voltage
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
Signature · 1 line
2.19.1
Reviewed-by on v3 5/5
#12 lore raw

Re: [PATCH v3 5/5] dt-bindings: drm/panel: simple: add sharp, lq070y3dg3b panel

Quoted 1 line · H. Nikolaus Schaller
Quoted 30 lines
---
 .../bindings/display/panel/sharp,lq070y3dg3b.txt     | 12 ++++++++++++
 1 file changed, 12 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/sharp,lq070y3dg3b.txt
Documentation/devicetree/bindings/display/panel/sharp,lq070y3dg3b.txt new file +12 -0
new file mode 100644
index 000000000000..95534b55ee5f
@@ -0,0 +1,12 @@
+Sharp LQ070Y3DG3B 7.0" WVGA landscape TFT LCD panel
+
+Required properties:
+- compatible: should be "sharp,lq070y3dg3b"
+
+Optional properties:
+- enable-gpios: GPIO pin to enable or disable the panel
+- backlight: phandle of the backlight device attached to the panel
+- power-supply: phandle of the regulator that provides the supply voltage
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
Signature · 6 lines
2.19.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

maintainer Reviewed-by on v3 5/5
#13 lore raw

Re: [PATCH v3 5/5] dt-bindings: drm/panel: simple: add sharp,lq070y3dg3b panel

In reply to H. Nikolaus Schaller
Quoted 6 lines · H. Nikolaus Schaller
---
 .../bindings/display/panel/sharp,lq070y3dg3b.txt     | 12 ++++++++++++
 1 file changed, 12 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/sharp,lq070y3dg3b.txt

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

#14 lore raw
In reply to H. Nikolaus Schaller

Hi,

Quoted 28 lines

Am 07.06.2019 um 13:11 schrieb H. Nikolaus Schaller <[email protected]>:

V3:
* add bindings documentation (suggested by [email protected])

V2 2019-06-05 07:07:05:
* fix typo in 99dtc panel compatible string (reported by [email protected])

V1 2019-06-04 14:53:00:

Since v5.2-rc1 OMAP is no longer using a special display driver architecture for DPI panels, but uses the general drm/panel/panel-simple.

So we finally can add SoC independent panel definitions for two panel models which we already had worked on quite a while ago (before device tree was introduced):

	https://patchwork.kernel.org/patch/2851295/

H. Nikolaus Schaller (5):
drm/panel: simple: Add Sharp LQ070Y3DG3B panel support drm/panel: simple: Add Ortustech COM37H3M panel support
dt-bindings: drm/panel: simple: add ortustech,com37h3m05dtc panel
dt-bindings: drm/panel: simple: add ortustech,com37h3m99dtc panel
dt-bindings: drm/panel: simple: add sharp,lq070y3dg3b panel

Quoted 12 lines
.../display/panel/ortustech,com37h3m05dtc.txt | 12 ++++
.../display/panel/ortustech,com37h3m99dtc.txt | 12 ++++
.../display/panel/sharp,lq070y3dg3b.txt       | 12 ++++
drivers/gpu/drm/panel/panel-simple.c          | 63 +++++++++++++++++++
4 files changed, 99 insertions(+)

create mode 100644 Documentation/devicetree/bindings/display/panel/ortustech,com37h3m05dtc.txt create mode 100644 Documentation/devicetree/bindings/display/panel/ortustech,com37h3m99dtc.txt create mode 100644 Documentation/devicetree/bindings/display/panel/sharp,lq070y3dg3b.txt

Signature · 1 line
2.19.1

any progress towards merging this somewhere? It did not yet arrive in linux-next.

BTW: should also be applied to 5.2

BR and thanks,
Nikolaus

#15 lore raw

Hi Nikolaus

Quoted 35 lines
Quoted 35 lines

V3:
* add bindings documentation (suggested by [email protected])

V2 2019-06-05 07:07:05:
* fix typo in 99dtc panel compatible string (reported by [email protected])

V1 2019-06-04 14:53:00:

Since v5.2-rc1 OMAP is no longer using a special display driver architecture for DPI panels, but uses the general drm/panel/panel-simple.

So we finally can add SoC independent panel definitions for two panel models which we already had worked on quite a while ago (before device tree was introduced):

	https://patchwork.kernel.org/patch/2851295/

H. Nikolaus Schaller (5):
drm/panel: simple: Add Sharp LQ070Y3DG3B panel support drm/panel: simple: Add Ortustech COM37H3M panel support
dt-bindings: drm/panel: simple: add ortustech,com37h3m05dtc panel
dt-bindings: drm/panel: simple: add ortustech,com37h3m99dtc panel
dt-bindings: drm/panel: simple: add sharp,lq070y3dg3b panel

.../display/panel/ortustech,com37h3m05dtc.txt | 12 ++++
.../display/panel/ortustech,com37h3m99dtc.txt | 12 ++++
.../display/panel/sharp,lq070y3dg3b.txt       | 12 ++++
drivers/gpu/drm/panel/panel-simple.c          | 63 +++++++++++++++++++
4 files changed, 99 insertions(+)

create mode 100644 Documentation/devicetree/bindings/display/panel/ortustech,com37h3m05dtc.txt create mode 100644 Documentation/devicetree/bindings/display/panel/ortustech,com37h3m99dtc.txt create mode 100644 Documentation/devicetree/bindings/display/panel/sharp,lq070y3dg3b.txt

Quoted 7 lines
Quoted 3 lines
Signature · 1 line
2.19.1

any progress towards merging this somewhere? It did not yet arrive in linux-next.

BTW: should also be applied to 5.2

The drm bits are reviewed. The DT bits needs OK from DT people. When we have OK from DT people we can apply them all to drm-misc-next.

If we need them expedited towards the upstream kernel you will need help from someone else. But let's get them in drm-misc-next first.

Sam

#16 lore raw

Hi Nikolaus.

Quoted 6 lines
Quoted 4 lines

any progress towards merging this somewhere? It did not yet arrive in linux-next.

BTW: should also be applied to 5.2

The drm bits are reviewed. The DT bits needs OK from DT people. When we have OK from DT people we can apply them all to drm-misc-next.

I got OK on irc from Rob to process these.
All patches are now applied to drm-misc-next.

Sam
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

#17 lore raw

Hi Sam,

Quoted 5 lines

Am 26.06.2019 um 09:33 schrieb Sam Ravnborg <[email protected]>:

Hi Nikolaus.

Quoted 1 line
Quoted 1 line
Quoted 8 lines
Quoted 5 lines
Quoted 3 lines

any progress towards merging this somewhere? It did not yet arrive in linux-next.

BTW: should also be applied to 5.2

The drm bits are reviewed. The DT bits needs OK from DT people. When we have OK from DT people we can apply them all to drm-misc-next.

I got OK on irc from Rob to process these.
All patches are now applied to drm-misc-next.

Thanks for taking care of this!

Quoted 2 lines

Sam

BR,
Nikolaus

#18 lore raw

Hi Sam,

Quoted 11 lines

Am 26.06.2019 um 14:40 schrieb H. Nikolaus Schaller <[email protected]>:

Hi Sam,

Quoted 7 lines

Am 26.06.2019 um 09:33 schrieb Sam Ravnborg <[email protected]>:

Hi Nikolaus.

Quoted 3 lines
Quoted 3 lines

any progress towards merging this somewhere? It did not yet arrive in linux-next.

Quoted 8 lines
Quoted 6 lines
Quoted 3 lines
Quoted 1 line

BTW: should also be applied to 5.2

The drm bits are reviewed. The DT bits needs OK from DT people. When we have OK from DT people we can apply them all to drm-misc-next.

I got OK on irc from Rob to process these.
All patches are now applied to drm-misc-next.

Thanks for taking care of this!

I have checked but it seems they are still not merged into linux-next.

BR and thanks,
Nikolaus

#19 lore raw

Hi Nikolaus.

Quoted 10 lines
Quoted 8 lines
Quoted 6 lines
Quoted 3 lines
Quoted 1 line

BTW: should also be applied to 5.2

The drm bits are reviewed. The DT bits needs OK from DT people. When we have OK from DT people we can apply them all to drm-misc-next.

I got OK on irc from Rob to process these.
All patches are now applied to drm-misc-next.

Thanks for taking care of this!

I have checked but it seems they are still not merged into linux-next.

They will appear in next merge window. They were to late to hit current merge window, as the cut-of time is around .rc5 in the drm subsystem. And this is not really a fix so not stable material.

Sam

#20 lore raw

Hi Sam,

Quoted 11 lines

Am 17.07.2019 um 20:14 schrieb Sam Ravnborg <[email protected]>:

Hi Nikolaus.

Quoted 7 lines
Quoted 7 lines
Quoted 6 lines
Quoted 3 lines
Quoted 1 line

BTW: should also be applied to 5.2

The drm bits are reviewed. The DT bits needs OK from DT people. When we have OK from DT people we can apply them all to drm-misc-next.

I got OK on irc from Rob to process these.
All patches are now applied to drm-misc-next.

Quoted 7 lines
Quoted 3 lines
Quoted 1 line

Thanks for taking care of this!

I have checked but it seems they are still not merged into linux-next.

They will appear in next merge window. They were to late to hit current merge window, as the cut-of time is around .rc5 in the drm subsystem. And this is not really a fix so not stable material.

have finally arrived. I just wasn't patient enough :)

BR and thanks,
Nikolaus