net: dsa: microchip: Convert to regmap
v4 cover net: dsa: microchip: Convert to regmap
This patchset converts KSZ9477 switch driver to regmap.
This was tested with extra patches on KSZ8795. This was also tested on KSZ9477 on Microchip KSZ9477EVB board, which I now have.
Marek Vasut (10):
net: dsa: microchip: Remove ksz_{read,write}24()
net: dsa: microchip: Remove ksz_{get,set}()
net: dsa: microchip: Inline ksz_spi.h
net: dsa: microchip: Move ksz_cfg and ksz_port_cfg to ksz9477.c
net: dsa: microchip: Use PORT_CTRL_ADDR() instead of indirect function
call
net: dsa: microchip: Factor out register access opcode generation
net: dsa: microchip: Initial SPI regmap support
net: dsa: microchip: Dispose of ksz_io_ops
net: dsa: microchip: Factor out regmap config generation into common
header
net: dsa: microchip: Replace ad-hoc bit manipulation with regmap
drivers/net/dsa/microchip/Kconfig | 1 + drivers/net/dsa/microchip/ksz9477.c | 35 +++--- drivers/net/dsa/microchip/ksz9477_spi.c | 114 +++-------------- drivers/net/dsa/microchip/ksz_common.c | 6 +- drivers/net/dsa/microchip/ksz_common.h | 157 +++++++----------------- drivers/net/dsa/microchip/ksz_priv.h | 23 +--- drivers/net/dsa/microchip/ksz_spi.h | 69 ----------- 7 files changed, 84 insertions(+), 321 deletions(-) delete mode 100644 drivers/net/dsa/microchip/ksz_spi.h
Signature · 1 line
2.20.1
PATCH v4 1/10 net: dsa: microchip: Remove ksz_{read,write}24()
These functions and callbacks are never used, remove them.
---
V2: No change
V3: - Rebase on next/master
- Test on KSZ9477EVB
V4: Add RB
--- drivers/net/dsa/microchip/ksz9477_spi.c | 25 ------------------------- drivers/net/dsa/microchip/ksz_common.h | 22 ---------------------- drivers/net/dsa/microchip/ksz_priv.h | 2 -- 3 files changed, 49 deletions(-)
drivers/net/dsa/microchip/ksz9477_spi.c +0 -25
@@ -73,37 +73,12 @@ static int ksz_spi_write(struct ksz_device *dev, u32 reg, void *data,return ksz9477_spi_write_reg (spi, reg, dev->txbuf, len); } -static int ksz_spi_read24 (struct ksz_device *dev,u32 reg,u32 *val) -{ -int ret; - - *val =0 ; - ret =ksz_spi_read (dev, reg, (u8 *)val,3 ); -if (!ret) { - *val =be32_to_cpu (*val); -/* convert to 24bit */ - *val >>=8 ; - } - -return ret; -} - -static int ksz_spi_write24 (struct ksz_device *dev,u32 reg,u32 value) -{ -/* make it to big endian 24bit from MSB */ - value <<=8 ; - value =cpu_to_be32 (value); -return ksz_spi_write (dev, reg, &value,3 ); -} -static const struct ksz_io_ops ksz9477_spi_ops = { .read8 = ksz_spi_read8, .read16 = ksz_spi_read16, - .read24 = ksz_spi_read24, .read32 = ksz_spi_read32, .write8 = ksz_spi_write8, .write16 = ksz_spi_write16, - .write24 = ksz_spi_write24, .write32 = ksz_spi_write32, .get = ksz_spi_get, .set = ksz_spi_set,
drivers/net/dsa/microchip/ksz_common.h +0 -22
@@ -61,17 +61,6 @@ static inline int ksz_read16(struct ksz_device *dev, u32 reg, u16 *val)return ret; } -static inline int ksz_read24 (struct ksz_device *dev,u32 reg,u32 *val) -{ -int ret; - -mutex_lock (&dev->reg_mutex); - ret = dev->ops->read24 (dev, reg, val); -mutex_unlock (&dev->reg_mutex); - -return ret; -} -static inline int ksz_read32 (struct ksz_device *dev,u32 reg,u32 *val) {int ret;
@@ -105,17 +94,6 @@ static inline int ksz_write16(struct ksz_device *dev, u32 reg, u16 value)return ret; } -static inline int ksz_write24 (struct ksz_device *dev,u32 reg,u32 value) -{ -int ret; - -mutex_lock (&dev->reg_mutex); - ret = dev->ops->write24 (dev, reg, value); -mutex_unlock (&dev->reg_mutex); - -return ret; -} -static inline int ksz_write32 (struct ksz_device *dev,u32 reg,u32 value) {int ret;
drivers/net/dsa/microchip/ksz_priv.h +0 -2
@@ -105,11 +105,9 @@ struct ksz_device {struct ksz_io_ops {int (*read8)(struct ksz_device *dev,u32 reg,u8 *value);int (*read16)(struct ksz_device *dev,u32 reg,u16 *value); -int (*read24)(struct ksz_device *dev,u32 reg,u32 *value);int (*read32)(struct ksz_device *dev,u32 reg,u32 *value);int (*write8)(struct ksz_device *dev,u32 reg,u8 value);int (*write16)(struct ksz_device *dev,u32 reg,u16 value); -int (*write24)(struct ksz_device *dev,u32 reg,u32 value);int (*write32)(struct ksz_device *dev,u32 reg,u32 value);int (*get)(struct ksz_device *dev,u32 reg,void *data,size_t len);int (*set)(struct ksz_device *dev,u32 reg,void *data,size_t len);
Signature · 1 line
2.20.1
PATCH v4 2/10 net: dsa: microchip: Remove ksz_{get,set}()
In reply to Marek VasutThese functions and callbacks are never used, remove them.
---
V2: No change
V3: - Rebase on next/master
- Test on KSZ9477EVB
V4: Add RB
--- drivers/net/dsa/microchip/ksz9477_spi.c | 2 -- drivers/net/dsa/microchip/ksz_common.h | 24 ------------------------ drivers/net/dsa/microchip/ksz_priv.h | 2 -- drivers/net/dsa/microchip/ksz_spi.h | 10 ---------- 4 files changed, 38 deletions(-)
drivers/net/dsa/microchip/ksz9477_spi.c +0 -2
@@ -80,8 +80,6 @@ static const struct ksz_io_ops ksz9477_spi_ops = { .write8 = ksz_spi_write8, .write16 = ksz_spi_write16, .write32 = ksz_spi_write32, - .get = ksz_spi_get, - .set = ksz_spi_set, };static int ksz9477_spi_probe (struct spi_device *spi)
drivers/net/dsa/microchip/ksz_common.h +0 -24
@@ -105,30 +105,6 @@ static inline int ksz_write32(struct ksz_device *dev, u32 reg, u32 value)return ret; } -static inline int ksz_get (struct ksz_device *dev,u32 reg,void *data, -size_t len) -{ -int ret; - -mutex_lock (&dev->reg_mutex); - ret = dev->ops->get (dev, reg, data, len); -mutex_unlock (&dev->reg_mutex); - -return ret; -} - -static inline int ksz_set (struct ksz_device *dev,u32 reg,void *data, -size_t len) -{ -int ret; - -mutex_lock (&dev->reg_mutex); - ret = dev->ops->set (dev, reg, data, len); -mutex_unlock (&dev->reg_mutex); - -return ret; -} -static inline void ksz_pread8 (struct ksz_device *dev,int port,int offset,u8 *data) {
drivers/net/dsa/microchip/ksz_priv.h +0 -2
@@ -109,8 +109,6 @@ struct ksz_io_ops {int (*write8)(struct ksz_device *dev,u32 reg,u8 value);int (*write16)(struct ksz_device *dev,u32 reg,u16 value);int (*write32)(struct ksz_device *dev,u32 reg,u32 value); -int (*get)(struct ksz_device *dev,u32 reg,void *data,size_t len); -int (*set)(struct ksz_device *dev,u32 reg,void *data,size_t len); };struct alu_struct {
drivers/net/dsa/microchip/ksz_spi.h +0 -10
@@ -56,14 +56,4 @@ static int ksz_spi_write32(struct ksz_device *dev, u32 reg, u32 value) return ksz_spi_write(dev, reg, &value, 4); } -static int ksz_spi_get (struct ksz_device *dev,u32 reg,void *data,size_t len) -{ -return ksz_spi_read (dev, reg, data, len); -} - -static int ksz_spi_set (struct ksz_device *dev,u32 reg,void *data,size_t len) -{ -return ksz_spi_write (dev, reg, data, len); -} -#endif
Signature · 1 line
2.20.1
PATCH v4 3/10 net: dsa: microchip: Inline ksz_spi.h
In reply to Marek VasutThe functions in the header file are static, and the header file is included from single C file, just inline the code into the C file. The bonus is that it's easier to spot further content to clean up.
---
V2: No change
V3: - Rebase on next/master
- Test on KSZ9477EVB
V4: Add RB
--- drivers/net/dsa/microchip/ksz9477_spi.c | 43 +++++++++++++++++- drivers/net/dsa/microchip/ksz_spi.h | 59 ------------------------- 2 files changed, 42 insertions(+), 60 deletions(-) delete mode 100644 drivers/net/dsa/microchip/ksz_spi.h
drivers/net/dsa/microchip/ksz9477_spi.c +42 -1
@@ -13,7 +13,6 @@#include <linux/spi/spi.h> #include "ksz_priv.h" -#include "ksz_spi.h" /* SPI frame opcodes */ #define KS_SPIOP_RD 3
@@ -73,6 +72,48 @@ static int ksz_spi_write(struct ksz_device *dev, u32 reg, void *data,return ksz9477_spi_write_reg (spi, reg, dev->txbuf, len); } +static int ksz_spi_read8 (struct ksz_device *dev,u32 reg,u8 *val) +{ +return ksz_spi_read (dev, reg, val,1 ); +} + +static int ksz_spi_read16 (struct ksz_device *dev,u32 reg,u16 *val) +{ +int ret =ksz_spi_read (dev, reg, (u8 *)val,2 ); + +if (!ret) + *val =be16_to_cpu (*val); + +return ret; +} + +static int ksz_spi_read32 (struct ksz_device *dev,u32 reg,u32 *val) +{ +int ret =ksz_spi_read (dev, reg, (u8 *)val,4 ); + +if (!ret) + *val =be32_to_cpu (*val); + +return ret; +} + +static int ksz_spi_write8 (struct ksz_device *dev,u32 reg,u8 value) +{ +return ksz_spi_write (dev, reg, &value,1 ); +} + +static int ksz_spi_write16 (struct ksz_device *dev,u32 reg,u16 value) +{ + value =cpu_to_be16 (value); +return ksz_spi_write (dev, reg, &value,2 ); +} + +static int ksz_spi_write32 (struct ksz_device *dev,u32 reg,u32 value) +{ + value =cpu_to_be32 (value); +return ksz_spi_write (dev, reg, &value,4 ); +} +static const struct ksz_io_ops ksz9477_spi_ops = { .read8 = ksz_spi_read8, .read16 = ksz_spi_read16,
drivers/net/dsa/microchip/ksz_spi.h deleted +0 -59
59 lines not on this page · raw message
Signature · 1 line
2.20.1
PATCH v4 4/10 net: dsa: microchip: Move ksz_cfg and ksz_port_cfg to ksz9477.c
In reply to Marek VasutThese functions are only used by the KSZ9477 code, move them from the header into that code. Note that these functions will be soon replaced by regmap equivalents.
---
V2: New patch
V3: - Rebase on next/master
- Test on KSZ9477EVB
V4: Add RB
--- drivers/net/dsa/microchip/ksz9477.c | 29 ++++++++++++++++++++++++++ drivers/net/dsa/microchip/ksz_common.h | 29 -------------------------- 2 files changed, 29 insertions(+), 29 deletions(-)
drivers/net/dsa/microchip/ksz9477.c +29 -0
@@ -65,6 +65,35 @@ static const struct { { 0x83, "tx_discards" }, }; +static void ksz_cfg (struct ksz_device *dev,u32 addr,u8 bits,bool set) +{ +u8 data; + +ksz_read8 (dev, addr, &data); +if (set) + data |= bits; +else + data &= ~bits; +ksz_write8 (dev, addr, data); +} + +static void ksz_port_cfg (struct ksz_device *dev,int port,int offset,u8 bits, +bool set) +{ +u32 addr; +u8 data; + + addr = dev->dev_ops->get_port_addr (port, offset); +ksz_read8 (dev, addr, &data); + +if (set) + data |= bits; +else + data &= ~bits; + +ksz_write8 (dev, addr, data); +} +static void ksz9477_cfg32 (struct ksz_device *dev,u32 addr,u32 bits,bool set) {u32 data;
drivers/net/dsa/microchip/ksz_common.h +0 -29
@@ -141,35 +141,6 @@ static inline void ksz_pwrite32(struct ksz_device *dev, int port, int offset,ksz_write32 (dev, dev->dev_ops->get_port_addr (port, offset), data); } -static void ksz_cfg (struct ksz_device *dev,u32 addr,u8 bits,bool set) -{ -u8 data; - -ksz_read8 (dev, addr, &data); -if (set) - data |= bits; -else - data &= ~bits; -ksz_write8 (dev, addr, data); -} - -static void ksz_port_cfg (struct ksz_device *dev,int port,int offset,u8 bits, -bool set) -{ -u32 addr; -u8 data; - - addr = dev->dev_ops->get_port_addr (port, offset); -ksz_read8 (dev, addr, &data); - -if (set) - data |= bits; -else - data &= ~bits; - -ksz_write8 (dev, addr, data); -} -struct ksz_poll_ctx {struct ksz_device *dev;int port;
Signature · 1 line
2.20.1
PATCH v4 5/10 net: dsa: microchip: Use PORT_CTRL_ADDR() instead of indirect function call
In reply to Marek VasutThe indirect function call to dev->dev_ops->get_port_addr() is expensive especially if called for every single register access, and only returns the value of PORT_CTRL_ADDR() macro. Use PORT_CTRL_ADDR() macro directly instead.
---
V2: New patch
V3: - Rebase on next/master
- Test on KSZ9477EVB
V4: No change
--- drivers/net/dsa/microchip/ksz9477.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/dsa/microchip/ksz9477.c +1 -1
@@ -83,7 +83,7 @@ static void ksz_port_cfg(struct ksz_device *dev, int port, int offset, u8 bits,u32 addr;u8 data; - addr = dev->dev_ops->get_port_addr (port, offset); + addr =PORT_CTRL_ADDR (port, offset);ksz_read8 (dev, addr, &data);if (set)
Signature · 1 line
2.20.1
PATCH v4 6/10 net: dsa: microchip: Factor out register access opcode generation
In reply to Marek VasutFactor out the code which sends out the register read/write opcodes to the switch, since the code differs in single bit between read and write.
---
V2: New patch
V3: - Rebase on next/master
- Test on KSZ9477EVB
V4: Add RB
--- drivers/net/dsa/microchip/ksz9477_spi.c | 22 ++++++++++++---------- 1 file changed, 12 insertions(+), 10 deletions(-)
drivers/net/dsa/microchip/ksz9477_spi.c +12 -10
@@ -25,19 +25,24 @@/* Enough to read all switch port registers. */ #define SPI_TX_BUF_LEN 0x100 -static int ksz9477_spi_read_reg (struct spi_device *spi,u32 reg,u8 *val, -unsigned int len) +static u32 ksz9477_spi_cmd (u32 reg,bool read) {u32 txbuf; -int ret; txbuf = reg &SPI_ADDR_MASK ; - txbuf |=KS_SPIOP_RD <<SPI_ADDR_SHIFT ; + txbuf |= (read ?KS_SPIOP_RD :KS_SPIOP_WR ) <<SPI_ADDR_SHIFT ; txbuf <<=SPI_TURNAROUND_SHIFT ; txbuf =cpu_to_be32 (txbuf); - ret =spi_write_then_read (spi, &txbuf,4 , val, len); -return ret; +return txbuf; +} + +static int ksz9477_spi_read_reg (struct spi_device *spi,u32 reg,u8 *val, +unsigned int len) +{ +u32 txbuf =ksz9477_spi_cmd (reg, true); + +return spi_write_then_read (spi, &txbuf,4 , val, len); } static int ksz9477_spi_write_reg(struct spi_device *spi, u32 reg, u8 *val,
@@ -45,10 +50,7 @@ static int ksz9477_spi_write_reg(struct spi_device *spi, u32 reg, u8 *val, {u32 *txbuf = (u32 *)val; - *txbuf = reg &SPI_ADDR_MASK ; - *txbuf |= (KS_SPIOP_WR <<SPI_ADDR_SHIFT ); - *txbuf <<=SPI_TURNAROUND_SHIFT ; - *txbuf =cpu_to_be32 (*txbuf); + *txbuf =ksz9477_spi_cmd (reg, false);return spi_write (spi, txbuf,4 + len); }
Signature · 1 line
2.20.1
PATCH v4 7/10 net: dsa: microchip: Initial SPI regmap support
In reply to Marek VasutAdd basic SPI regmap support into the driver.
Previous patches unconver that ksz_spi_write() is always ever called with len = 1, 2 or 4. We can thus drop the if (len > SPI_TX_BUF_LEN) check and we can also drop the allocation of the txbuf which is part of the driver data and wastes 256 bytes for no reason. Regmap covers the whole thing now.
---
V2: - Squash with "net: dsa: microchip: Remove dev->txbuf"
- Use separate regmaps for 8/16/32bit registers
- Increase the regmap size to 0xd00 to cover the entire register area
V3: - Rebase on next/master
- Test on KSZ9477EVB
- Increase regmap max register, to cover all switch registers
- Correct regmap reg_bits value to match the hardware
- Use cpu_to_be32() instead of cpu_to_le16() in register masks, since the KSZ9477 has some 32bit registers.
V4: - Replace cpu_to_be32() with swab32() in regmap read/write_flag_masks.
- Move REGMAP_SPI to NET_DSA_MICROCHIP_KSZ9477_SPI in Kconfig
--- drivers/net/dsa/microchip/Kconfig | 1 + drivers/net/dsa/microchip/ksz9477_spi.c | 114 +++++++++++------------- drivers/net/dsa/microchip/ksz_priv.h | 3 +- 3 files changed, 52 insertions(+), 66 deletions(-)
drivers/net/dsa/microchip/Kconfig +1 -0
@@ -13,5 +13,6 @@ menuconfig NET_DSA_MICROCHIP_KSZ9477 config NET_DSA_MICROCHIP_KSZ9477_SPI tristate "KSZ9477 series SPI connected switch driver" depends on NET_DSA_MICROCHIP_KSZ9477 && SPI + select REGMAP_SPI help Select to enable support for registering switches configured through SPI.
drivers/net/dsa/microchip/ksz9477_spi.c +50 -64
171 lines not on this page · raw message
drivers/net/dsa/microchip/ksz_priv.h +1 -2
@@ -57,6 +57,7 @@ struct ksz_device {const struct ksz_dev_ops *dev_ops;struct device *dev; +struct regmap *regmap[3 ];void *priv;
@@ -82,8 +83,6 @@ struct ksz_device {struct vlan_table *vlan_cache; -u8 *txbuf; -struct ksz_port *ports;struct timer_list mib_read_timer;struct work_struct mib_read;
Signature · 1 line
2.20.1
PATCH v4 8/10 net: dsa: microchip: Dispose of ksz_io_ops
In reply to Marek VasutSince the driver now uses regmap , get rid of ad-hoc ksz_io_ops abstraction, which no longer has any meaning. Moreover, since regmap has it's own locking, get rid of the register access mutex.
---
V2: Use separate regmaps for 8/16/32bit registers
V3: - Rebase on next/master
- Test on KSZ9477EVB
V4: No change
--- drivers/net/dsa/microchip/ksz9477_spi.c | 57 +------------------------ drivers/net/dsa/microchip/ksz_common.c | 6 +-- drivers/net/dsa/microchip/ksz_common.h | 50 ++++++---------------- drivers/net/dsa/microchip/ksz_priv.h | 16 +------ 4 files changed, 17 insertions(+), 112 deletions(-)
drivers/net/dsa/microchip/ksz9477_spi.c +1 -56
@@ -46,67 +46,12 @@ static const struct regmap_config ksz9477_regmap_config[] = { KSZ_REGMAP_COMMON(32), }; -static int ksz_spi_read8 (struct ksz_device *dev,u32 reg,u8 *val) -{ -unsigned int value; -int ret =regmap_read (dev->regmap, reg, &value); - - *val = value; -return ret; -} - -static int ksz_spi_read16 (struct ksz_device *dev,u32 reg,u16 *val) -{ -int ret =regmap_bulk_read (dev->regmap, reg, val,2 ); - -if (!ret) - *val =be16_to_cpu (*val); - -return ret; -} - -static int ksz_spi_read32 (struct ksz_device *dev,u32 reg,u32 *val) -{ -int ret =regmap_bulk_read (dev->regmap, reg, val,4 ); - -if (!ret) - *val =be32_to_cpu (*val); - -return ret; -} - -static int ksz_spi_write8 (struct ksz_device *dev,u32 reg,u8 value) -{ -return regmap_write (dev->regmap, reg, value); -} - -static int ksz_spi_write16 (struct ksz_device *dev,u32 reg,u16 value) -{ - value =cpu_to_be16 (value); -return regmap_bulk_write (dev->regmap, reg, &value,2 ); -} - -static int ksz_spi_write32 (struct ksz_device *dev,u32 reg,u32 value) -{ - value =cpu_to_be32 (value); -return regmap_bulk_write (dev->regmap, reg, &value,4 ); -} - -static const struct ksz_io_ops ksz9477_spi_ops = { - .read8 = ksz_spi_read8, - .read16 = ksz_spi_read16, - .read32 = ksz_spi_read32, - .write8 = ksz_spi_write8, - .write16 = ksz_spi_write16, - .write32 = ksz_spi_write32, -}; -static int ksz9477_spi_probe (struct spi_device *spi) {struct ksz_device *dev;int i, ret; - dev =ksz_switch_alloc (&spi->dev, &ksz9477_spi_ops, spi); + dev =ksz_switch_alloc (&spi->dev, spi);if (!dev)return -ENOMEM ;
drivers/net/dsa/microchip/ksz_common.c +1 -5
@@ -396,9 +396,7 @@ void ksz_disable_port(struct dsa_switch *ds, int port) }EXPORT_SYMBOL_GPL (ksz_disable_port); -struct ksz_device *ksz_switch_alloc (struct device *base, -const struct ksz_io_ops *ops, -void *priv) +struct ksz_device *ksz_switch_alloc (struct device *base,void *priv) {struct dsa_switch *ds;struct ksz_device *swdev;
@@ -416,7 +414,6 @@ struct ksz_device *ksz_switch_alloc(struct device *base, swdev->ds = ds; swdev->priv = priv; - swdev->ops = ops;return swdev; }
@@ -442,7 +439,6 @@ int ksz_switch_register(struct ksz_device *dev, }mutex_init (&dev->dev_mutex); -mutex_init (&dev->reg_mutex);mutex_init (&dev->stats_mutex);mutex_init (&dev->alu_mutex);mutex_init (&dev->vlan_mutex);
drivers/net/dsa/microchip/ksz_common.h +14 -36
88 lines not on this page · raw message
drivers/net/dsa/microchip/ksz_priv.h +1 -15
@@ -14,8 +14,6 @@#include <linux/etherdevice.h> #include <net/dsa.h> -struct ksz_io_ops ; -struct vlan_table {u32 table[3 ]; };
@@ -49,11 +47,9 @@ struct ksz_device {const char *name;struct mutex dev_mutex;/* device access */ -struct mutex reg_mutex;/* register access */ struct mutex stats_mutex;/* status access */ struct mutex alu_mutex;/* ALU access */ struct mutex vlan_mutex;/* vlan access */ -const struct ksz_io_ops *ops;const struct ksz_dev_ops *dev_ops;struct device *dev;
@@ -101,15 +97,6 @@ struct ksz_device {u16 port_mask; }; -struct ksz_io_ops { -int (*read8)(struct ksz_device *dev,u32 reg,u8 *value); -int (*read16)(struct ksz_device *dev,u32 reg,u16 *value); -int (*read32)(struct ksz_device *dev,u32 reg,u32 *value); -int (*write8)(struct ksz_device *dev,u32 reg,u8 value); -int (*write16)(struct ksz_device *dev,u32 reg,u16 value); -int (*write32)(struct ksz_device *dev,u32 reg,u32 value); -}; -struct alu_struct {/* entry 1 */ u8 is_static:1 ;
@@ -158,8 +145,7 @@ struct ksz_dev_ops {void (*exit)(struct ksz_device *dev); }; -struct ksz_device *ksz_switch_alloc (struct device *base, -const struct ksz_io_ops *ops,void *priv); +struct ksz_device *ksz_switch_alloc (struct device *base,void *priv);int ksz_switch_register (struct ksz_device *dev,const struct ksz_dev_ops *ops);void ksz_switch_remove (struct ksz_device *dev);
Signature · 1 line
2.20.1
PATCH v4 9/10 net: dsa: microchip: Factor out regmap config generation into common header
In reply to Marek VasutThe regmap config tables are rather similar for various generations of the KSZ8xxx/KSZ9xxx switches. Introduce a macro which allows generating those tables without duplication. Note that $regalign parameter is not used right now, but will be used in KSZ87xx series switches.
---
V2: New patch
V3: - Rebase on next/master
- Test on KSZ9477EVB
- Increase regmap max register, to cover all switch registers
- Make register swabbing configurable, to allow handling switches with only 16bit registers as well as switches with some 32bit ones
V4: No change
--- drivers/net/dsa/microchip/ksz9477_spi.c | 29 +++------------------- drivers/net/dsa/microchip/ksz_common.h | 32 +++++++++++++++++++++++++ 2 files changed, 35 insertions(+), 26 deletions(-)
drivers/net/dsa/microchip/ksz9477_spi.c +3 -26
@@ -14,37 +14,14 @@#include <linux/spi/spi.h> #include "ksz_priv.h" +#include "ksz_common.h" #define SPI_ADDR_SHIFT 24#define SPI_ADDR_ALIGN 3#define SPI_TURNAROUND_SHIFT 5 -/* SPI frame opcodes */ -#define KS_SPIOP_RD 3 -#define KS_SPIOP_WR 2 - -#define KS_SPIOP_FLAG_MASK (opcode) \ - swab32((opcode) << (SPI_ADDR_SHIFT + SPI_TURNAROUND_SHIFT)) - -#define KSZ_REGMAP_COMMON (width) \ - { \ - .val_bits = (width), \ - .reg_stride = (width) / 8, \ - .reg_bits = SPI_ADDR_SHIFT + SPI_ADDR_ALIGN, \ - .pad_bits = SPI_TURNAROUND_SHIFT, \ - .max_register = BIT(SPI_ADDR_SHIFT) - 1, \ - .cache_type = REGCACHE_NONE, \ - .read_flag_mask = KS_SPIOP_FLAG_MASK(KS_SPIOP_RD), \ - .write_flag_mask = KS_SPIOP_FLAG_MASK(KS_SPIOP_WR), \ - .reg_format_endian = REGMAP_ENDIAN_BIG, \ - .val_format_endian = REGMAP_ENDIAN_BIG \ - } - -static const struct regmap_config ksz9477_regmap_config[] = { -KSZ_REGMAP_COMMON (8 ), -KSZ_REGMAP_COMMON (16 ), -KSZ_REGMAP_COMMON (32 ), -}; +KSZ_REGMAP_TABLE (ksz9477,32 ,SPI_ADDR_SHIFT , +SPI_TURNAROUND_SHIFT ,SPI_ADDR_ALIGN );static int ksz9477_spi_probe (struct spi_device *spi) {
drivers/net/dsa/microchip/ksz_common.h +32 -0
@@ -133,4 +133,36 @@ static inline u32 ksz_pread32_poll(struct ksz_poll_ctx *ctx) return data; } +/* Regmap tables generation */ +#define KSZ_SPI_OP_RD 3 +#define KSZ_SPI_OP_WR 2 + +#define KSZ_SPI_OP_FLAG_MASK (opcode, swp, regbits, regpad) \ + swab##swp((opcode) << ((regbits) + (regpad))) + +#define KSZ_REGMAP_ENTRY (width, swp, regbits, regpad, regalign) \ + { \ + .val_bits = (width), \ + .reg_stride = (width) / 8, \ + .reg_bits = (regbits) + (regalign), \ + .pad_bits = (regpad), \ + .max_register = BIT(regbits) - 1, \ + .cache_type = REGCACHE_NONE, \ + .read_flag_mask = \ + KSZ_SPI_OP_FLAG_MASK(KSZ_SPI_OP_RD, swp, \ + regbits, regpad), \ + .write_flag_mask = \ + KSZ_SPI_OP_FLAG_MASK(KSZ_SPI_OP_WR, swp, \ + regbits, regpad), \ + .reg_format_endian = REGMAP_ENDIAN_BIG, \ + .val_format_endian = REGMAP_ENDIAN_BIG \ + } + +#define KSZ_REGMAP_TABLE (ksz, swp, regbits, regpad, regalign) \ + static const struct regmap_config ksz##_regmap_config[] = { \ + KSZ_REGMAP_ENTRY(8, swp, (regbits), (regpad), (regalign)), \ + KSZ_REGMAP_ENTRY(16, swp, (regbits), (regpad), (regalign)), \ + KSZ_REGMAP_ENTRY(32, swp, (regbits), (regpad), (regalign)), \ + } +#endif
Signature · 1 line
2.20.1
PATCH v4 10/10 net: dsa: microchip: Replace ad-hoc bit manipulation with regmap
In reply to Marek VasutRegmap provides bit manipulation functions to set/clear bits, use those insted of reimplementing them.
---
V2: New patch
V3: - Rebase on next/master
- Test on KSZ9477EVB
V4: No change
--- drivers/net/dsa/microchip/ksz9477.c | 46 ++++------------------------- 1 file changed, 6 insertions(+), 40 deletions(-)
drivers/net/dsa/microchip/ksz9477.c +6 -40
@@ -67,60 +67,26 @@ static const struct {static void ksz_cfg (struct ksz_device *dev,u32 addr,u8 bits,bool set) { -u8 data; - -ksz_read8 (dev, addr, &data); -if (set) - data |= bits; -else - data &= ~bits; -ksz_write8 (dev, addr, data); +regmap_update_bits (dev->regmap[0 ], addr, bits, set ? bits :0 ); }static void ksz_port_cfg (struct ksz_device *dev,int port,int offset,u8 bits,bool set) { -u32 addr; -u8 data; - - addr =PORT_CTRL_ADDR (port, offset); -ksz_read8 (dev, addr, &data); - -if (set) - data |= bits; -else - data &= ~bits; - -ksz_write8 (dev, addr, data); +regmap_update_bits (dev->regmap[0 ],PORT_CTRL_ADDR (port, offset), + bits, set ? bits :0 ); }static void ksz9477_cfg32 (struct ksz_device *dev,u32 addr,u32 bits,bool set) { -u32 data; - -ksz_read32 (dev, addr, &data); -if (set) - data |= bits; -else - data &= ~bits; -ksz_write32 (dev, addr, data); +regmap_update_bits (dev->regmap[2 ], addr, bits, set ? bits :0 ); }static void ksz9477_port_cfg32 (struct ksz_device *dev,int port,int offset,u32 bits,bool set) { -u32 addr; -u32 data; - - addr =PORT_CTRL_ADDR (port, offset); -ksz_read32 (dev, addr, &data); - -if (set) - data |= bits; -else - data &= ~bits; - -ksz_write32 (dev, addr, data); +regmap_update_bits (dev->regmap[2 ],PORT_CTRL_ADDR (port, offset), + bits, set ? bits :0 ); } static int ksz9477_wait_vlan_ctrl_ready(struct ksz_device *dev, u32 waiton,
Signature · 1 line
2.20.1
David Miller
maintainerFrom: Marek Vasut <[email protected]>
Date: Wed, 26 Jun 2019 01:43:38 +0200
Quoted 6 lines
This patchset converts KSZ9477 switch driver to regmap.
This was tested with extra patches on KSZ8795. This was also tested on KSZ9477 on Microchip KSZ9477EVB board, which I now have.
Signed-off-by Marek Vasut <[email protected]>
Series applied, thanks.