iio: adc: ad7124: Remove input number limitation
Subsystems (3)
PATCH v4 1/5 iio: adc: ad7124: Remove input number limitation
The driver limits the user to use only 4/8 differential inputs, but this device has the option to use pseudo-differential channels. This will increase the number of channels to be equal with the number of inputs so 8 channels for ad7124-4 and 16 for ad7124-8.
This patch removes the check between channel nodes and num_inputs value.
---
Changelog v2:
- nothing changed here
Changelog v3:
- nothing changed here
Changelog v4:
- nothing changed here
drivers/iio/adc/ad7124.c | 7 ------- 1 file changed, 7 deletions(-)
drivers/iio/adc/ad7124.c +0 -7
@@ -462,13 +462,6 @@ static int ad7124_of_parse_channel_config(struct iio_dev *indio_dev,if (ret) goto err; -if (ain[0 ] >= st->chip_info->num_inputs || - ain[1 ] >= st->chip_info->num_inputs) { -dev_err (indio_dev->dev.parent, -"Input pin number out of range.\n" ); - ret = -EINVAL ; - goto err; - } st->channel_config[channel].ain =AD7124_CHANNEL_AINP (ain[0 ]) |AD7124_CHANNEL_AINM (ain[1 ]); st->channel_config[channel].bipolar =
Signature · 1 line
2.17.1
PATCH v4 2/5 iio: adc: ad7124: Add buffered input support
This patch adds the option to enable the buffered mode for positive and negative inputs. Each option can be enabled independently.
In buffered mode, the input channel feeds into a high impedance input stage of the buffer amplifier. Therefore, the input can tolerate significant source impedances and is tailored for direct connection to external resistive type sensors such as strain gages or RTDs.
---
Changelog v2:
- nothing changed here
Changelog v3:
- nothing changed here
Changelog v4:
- nothing changed here
drivers/iio/adc/ad7124.c | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-)
drivers/iio/adc/ad7124.c +15 -2
@@ -61,6 +61,8 @@#define AD7124_CONFIG_REF_SEL (x) FIELD_PREP(AD7124_CONFIG_REF_SEL_MSK, x)#define AD7124_CONFIG_PGA_MSK GENMASK(2, 0)#define AD7124_CONFIG_PGA (x) FIELD_PREP(AD7124_CONFIG_PGA_MSK, x) +#define AD7124_CONFIG_IN_BUFF_MSK GENMASK(7, 6) +#define AD7124_CONFIG_IN_BUFF (x) FIELD_PREP(AD7124_CONFIG_IN_BUFF_MSK, x)/* AD7124_FILTER_X */ #define AD7124_FILTER_FS_MSK GENMASK(10, 0)
@@ -108,6 +110,8 @@ struct ad7124_chip_info {struct ad7124_channel_config {enum ad7124_ref_sel refsel;bool bipolar; +bool buf_positive; +bool buf_negative;unsigned int ain;unsigned int vref_mv;unsigned int pga_bits;
@@ -473,6 +477,11 @@ static int ad7124_of_parse_channel_config(struct iio_dev *indio_dev,else st->channel_config[channel].refsel = tmp; + st->channel_config[channel].buf_positive = +of_property_read_bool (child,"adi,buffered-positive" ); + st->channel_config[channel].buf_negative = +of_property_read_bool (child,"adi,buffered-negative" ); + *chan = ad7124_channel_template; chan->address = channel; chan->scan_index = channel;
@@ -492,7 +501,7 @@ static int ad7124_of_parse_channel_config(struct iio_dev *indio_dev,static int ad7124_setup (struct ad7124_state *st) {unsigned int val, fclk, power_mode; -int i, ret; +int i, ret, tmp; fclk =clk_get_rate (st->mclk);if (!fclk)
@@ -525,8 +534,12 @@ static int ad7124_setup(struct ad7124_state *st)if (ret <0 )return ret; + tmp = (st->channel_config[i].buf_positive <<1 ) + + st->channel_config[i].buf_negative; + val =AD7124_CONFIG_BIPOLAR (st->channel_config[i].bipolar) | -AD7124_CONFIG_REF_SEL (st->channel_config[i].refsel); +AD7124_CONFIG_REF_SEL (st->channel_config[i].refsel) | +AD7124_CONFIG_IN_BUFF (tmp); ret =ad_sd_write_reg (&st->sd,AD7124_CONFIG (i),2 , val);if (ret <0 )return ret;
Signature · 1 line
2.17.1
Re: [PATCHi V4 2/5] iio: adc: ad7124: Add buffered input support
Quoted 9 lines · On Tue, 25 Jun 2019 11:11:25 +0300 Mircea Caprioru…
This patch adds the option to enable the buffered mode for positive and negative inputs. Each option can be enabled independently.
In buffered mode, the input channel feeds into a high impedance input stage of the buffer amplifier. Therefore, the input can tolerate significant source impedances and is tailored for direct connection to external resistive type sensors such as strain gages or RTDs.
Signed-off-by Mircea Caprioru <[email protected]>
Applied.
Thanks,
Jonathan
Quoted 71 lines
---
Changelog v2:
- nothing changed hereChangelog v3:
- nothing changed hereChangelog v4:
- nothing changed heredrivers/iio/adc/ad7124.c | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-)drivers/iio/adc/ad7124.c +15
-2@@ -61,6 +61,8 @@#define AD7124_CONFIG_REF_SEL (x) FIELD_PREP(AD7124_CONFIG_REF_SEL_MSK, x)#define AD7124_CONFIG_PGA_MSK GENMASK(2, 0)#define AD7124_CONFIG_PGA (x) FIELD_PREP(AD7124_CONFIG_PGA_MSK, x) +#define AD7124_CONFIG_IN_BUFF_MSK GENMASK(7, 6) +#define AD7124_CONFIG_IN_BUFF (x) FIELD_PREP(AD7124_CONFIG_IN_BUFF_MSK, x)/* AD7124_FILTER_X */ #define AD7124_FILTER_FS_MSK GENMASK(10, 0)@@ -108,6 +110,8 @@ struct ad7124_chip_info {struct ad7124_channel_config {enum ad7124_ref_sel refsel;bool bipolar; +bool buf_positive; +bool buf_negative;unsigned int ain;unsigned int vref_mv;unsigned int pga_bits;@@ -473,6 +477,11 @@ static int ad7124_of_parse_channel_config(struct iio_dev *indio_dev,else st->channel_config[channel].refsel = tmp; + st->channel_config[channel].buf_positive = +of_property_read_bool (child,"adi,buffered-positive" ); + st->channel_config[channel].buf_negative = +of_property_read_bool (child,"adi,buffered-negative" ); + *chan = ad7124_channel_template; chan->address = channel; chan->scan_index = channel;@@ -492,7 +501,7 @@ static int ad7124_of_parse_channel_config(struct iio_dev *indio_dev,static int ad7124_setup (struct ad7124_state *st) {unsigned int val, fclk, power_mode; -int i, ret; +int i, ret, tmp; fclk =clk_get_rate (st->mclk);if (!fclk)@@ -525,8 +534,12 @@ static int ad7124_setup(struct ad7124_state *st)if (ret <0 )return ret; + tmp = (st->channel_config[i].buf_positive <<1 ) + + st->channel_config[i].buf_negative; + val =AD7124_CONFIG_BIPOLAR (st->channel_config[i].bipolar) | -AD7124_CONFIG_REF_SEL (st->channel_config[i].refsel); +AD7124_CONFIG_REF_SEL (st->channel_config[i].refsel) | +AD7124_CONFIG_IN_BUFF (tmp); ret =ad_sd_write_reg (&st->sd,AD7124_CONFIG (i),2 , val);if (ret <0 )return ret;
PATCH v4 3/5 iio: adc: ad7124: Shift to dynamic allocation for channel configuration
In reply to Mircea CaprioruThis patch changes the channel configuration member of the device structure from a fixed size array to a dynamic allocated one with a size equal to the number of channels specified in the device tree. This will ensure a more flexibility for compatible devices.
Ex. ad7124-4 - can have 4 differential or 8 pseudo-differential channels ad7124-8 - can have 8 differential or 16 pseudo-differential channels
Also the device can suspport any other combination of differential and pseudo-differential channels base on the physical number of inputs available.
---
Changelog v2:
- nothing changed here
Changelog v3:
- nothing changed here
Changelog v4:
- nothing changed here
drivers/iio/adc/ad7124.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)
drivers/iio/adc/ad7124.c +8 -1
@@ -121,7 +121,7 @@ struct ad7124_channel_config {struct ad7124_state {const struct ad7124_chip_info *chip_info;struct ad_sigma_delta sd; -struct ad7124_channel_config channel_config[4 ]; +struct ad7124_channel_config *channel_config;struct regulator *vref[4 ];struct clk *mclk;unsigned int adc_control;
@@ -439,6 +439,7 @@ static int ad7124_of_parse_channel_config(struct iio_dev *indio_dev,struct ad7124_state *st =iio_priv (indio_dev);struct device_node *child;struct iio_chan_spec *chan; +struct ad7124_channel_config *chan_config;unsigned int ain[2 ], channel =0 , tmp;int ret;
@@ -453,8 +454,14 @@ static int ad7124_of_parse_channel_config(struct iio_dev *indio_dev,if (!chan)return -ENOMEM ; + chan_config =devm_kcalloc (indio_dev->dev.parent, st->num_channels, +sizeof (*chan_config),GFP_KERNEL ); +if (!chan_config) +return -ENOMEM ; + indio_dev->channels = chan; indio_dev->num_channels = st->num_channels; + st->channel_config = chan_config;for_each_available_child_of_node (np, child) { ret =of_property_read_u32 (child,"reg" , &channel);
Signature · 1 line
2.17.1
Re: [PATCH V4 3/5] iio: adc: ad7124: Shift to dynamic allocation for channel configuration
Quoted 5 lines · On Tue, 25 Jun 2019 11:11:26 +0300 Mircea Caprioru…
This patch changes the channel configuration member of the device structure from a fixed size array to a dynamic allocated one with a size equal to the number of channels specified in the device tree. This will ensure a more flexibility for compatible devices.
Quoted 8 lines
Ex. ad7124-4 - can have 4 differential or 8 pseudo-differential channels ad7124-8 - can have 8 differential or 16 pseudo-differential channels
Also the device can suspport any other combination of differential and pseudo-differential channels base on the physical number of inputs available.
Signed-off-by Mircea Caprioru <[email protected]>
Applied.
Thanks,
Jonathan
Quoted 50 lines
---
Changelog v2:
- nothing changed hereChangelog v3:
- nothing changed hereChangelog v4:
- nothing changed heredrivers/iio/adc/ad7124.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)drivers/iio/adc/ad7124.c +8
-1@@ -121,7 +121,7 @@ struct ad7124_channel_config {struct ad7124_state {const struct ad7124_chip_info *chip_info;struct ad_sigma_delta sd; -struct ad7124_channel_config channel_config[4 ]; +struct ad7124_channel_config *channel_config;struct regulator *vref[4 ];struct clk *mclk;unsigned int adc_control;@@ -439,6 +439,7 @@ static int ad7124_of_parse_channel_config(struct iio_dev *indio_dev,struct ad7124_state *st =iio_priv (indio_dev);struct device_node *child;struct iio_chan_spec *chan; +struct ad7124_channel_config *chan_config;unsigned int ain[2 ], channel =0 , tmp;int ret;@@ -453,8 +454,14 @@ static int ad7124_of_parse_channel_config(struct iio_dev *indio_dev,if (!chan)return -ENOMEM ; + chan_config =devm_kcalloc (indio_dev->dev.parent, st->num_channels, +sizeof (*chan_config),GFP_KERNEL ); +if (!chan_config) +return -ENOMEM ; + indio_dev->channels = chan; indio_dev->num_channels = st->num_channels; + st->channel_config = chan_config;for_each_available_child_of_node (np, child) { ret =of_property_read_u32 (child,"reg" , &channel);
PATCH v4 4/5 dt-bindings: iio: adc: Convert ad7124 documentation to YAML
In reply to Mircea CaprioruConvert AD7124 bindings documentation to YAML format.
---
Changelog v2:
- modified SPDX license to GPL-2.0 OR BSD-2-Clause
- added regex for a range from 0 to 15
- added minimum and maximum constraints for reg property
- set type and range of values for adi,reference-select property
- used items for diff-channels property
- set bipolar, adi,buffered-positive and negative to type: boolean
Changelog v3:
- moved adi,buffered-positive and negative properties to own commit
Changelog v4:
- removed old txt dt-binding
.../bindings/iio/adc/adi,ad7124.txt | 75 --------- .../bindings/iio/adc/adi,ad7124.yaml | 144 ++++++++++++++++++ 2 files changed, 144 insertions(+), 75 deletions(-) delete mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7124.yaml
Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt deleted +0 -75
@@ -1,75 +0,0 @@ -Analog Devices AD7124 ADC device driver - -Required properties for the AD7124: - - compatible: Must be one of "adi,ad7124-4" or "adi,ad7124-8" - - reg: SPI chip select number for the device - - spi-max-frequency: Max SPI frequency to use - see: Documentation/devicetree/bindings/spi/spi-bus.txt - - clocks: phandle to the master clock (mclk) - see: Documentation/devicetree/bindings/clock/clock-bindings.txt - - clock-names: Must be "mclk". - - interrupts: IRQ line for the ADC - see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - - Required properties: - * #address-cells: Must be 1. - * #size-cells: Must be 0. - - Subnode(s) represent the external channels which are connected to the ADC. - Each subnode represents one channel and has the following properties: - Required properties: - * reg: The channel number. It can have up to 4 channels on ad7124-4 - and 8 channels on ad7124-8, numbered from 0 to 15. - * diff-channels: see: Documentation/devicetree/bindings/iio/adc/adc.txt - - Optional properties: - * bipolar: see: Documentation/devicetree/bindings/iio/adc/adc.txt - * adi,reference-select: Select the reference source to use when - converting on the the specific channel. Valid values are: - 0: REFIN1(+)/REFIN1(−). - 1: REFIN2(+)/REFIN2(−). - 3: AVDD - If this field is left empty, internal reference is selected. - -Optional properties: - - refin1-supply: refin1 supply can be used as reference for conversion. - - refin2-supply: refin2 supply can be used as reference for conversion. - - avdd-supply: avdd supply can be used as reference for conversion. - -Example: - adc@0 { - compatible = "adi,ad7124-4"; - reg = <0>; - spi-max-frequency = <5000000>; - interrupts = <25 2>; - interrupt-parent = <&gpio>; - refin1-supply = <&adc_vref>; - clocks = <&ad7124_mclk>; - clock-names = "mclk"; - - #address-cells = <1>; - #size-cells = <0>; - - channel@0 { - reg = <0>; - diff-channels = <0 1>; - adi,reference-select = <0>; - }; - - channel@1 { - reg = <1>; - bipolar; - diff-channels = <2 3>; - adi,reference-select = <0>; - }; - - channel@2 { - reg = <2>; - diff-channels = <4 5>; - }; - - channel@3 { - reg = <3>; - diff-channels = <6 7>; - }; - };
Documentation/devicetree/bindings/iio/adc/adi,ad7124.yaml new file +144 -0
144 lines not on this page · raw message
Signature · 1 line
2.17.1
Re: [PATCH V4 4/5] dt-bindings: iio: adc: Convert ad7124 documentation to YAML
Quoted 17 lines · Mircea Caprioru
Convert AD7124 bindings documentation to YAML format.
Signed-off-by Mircea Caprioru <[email protected]>---
Changelog v2:
- modified SPDX license to GPL-2.0 OR BSD-2-Clause
- added regex for a range from 0 to 15
- added minimum and maximum constraints for reg property
- set type and range of values for adi,reference-select property
- used items for diff-channels property
- set bipolar, adi,buffered-positive and negative to type: booleanChangelog v3:
- moved adi,buffered-positive and negative properties to own commit
Quoted 8 lines
Changelog v4:
- removed old txt dt-binding.../bindings/iio/adc/adi,ad7124.txt | 75 --------- .../bindings/iio/adc/adi,ad7124.yaml | 144 ++++++++++++++++++ 2 files changed, 144 insertions(+), 75 deletions(-) delete mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7124.yaml
Jonathan Cameron
maintainerRe: [PATCH V4 4/5] dt-bindings: iio: adc: Convert ad7124 documentation to YAML
Quoted 22 lines · On Wed, 26 Jun 2019 08:44:36 -0600 Rob Herring <[email protected]> wrote:
Quoted 20 lines · Mircea Caprioru
Convert AD7124 bindings documentation to YAML format.
Signed-off-by Mircea Caprioru <[email protected]>---
Changelog v2:
- modified SPDX license to GPL-2.0 OR BSD-2-Clause
- added regex for a range from 0 to 15
- added minimum and maximum constraints for reg property
- set type and range of values for adi,reference-select property
- used items for diff-channels property
- set bipolar, adi,buffered-positive and negative to type: booleanChangelog v3:
- moved adi,buffered-positive and negative properties to own commitChangelog v4:
- removed old txt dt-binding
Quoted 7 lines
Quoted 5 lines
.../bindings/iio/adc/adi,ad7124.txt | 75 --------- .../bindings/iio/adc/adi,ad7124.yaml | 144 ++++++++++++++++++ 2 files changed, 144 insertions(+), 75 deletions(-) delete mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7124.yamlReviewed-by Rob Herring <[email protected]>
Something a bit odd happened when trying to apply this, so I ended up doing it rather manually.
error: cannot convert from y to UTF-8
fatal: could not parse patch
Anyhow, I think it's fine now, but would welcome any suggestion on what causes that one? Patch was perfectly happy with it.
Jonathan
Re: [PATCH V4 4/5] dt-bindings: iio: adc: Convert ad7124 documentation to YAML
Quoted 33 lines · Jonathan Cameron
Quoted 22 lines · On Wed, 26 Jun 2019 08:44:36 -0600 Rob Herring <[email protected]> wrote:
Quoted 20 lines · Mircea Caprioru
Convert AD7124 bindings documentation to YAML format.
Signed-off-by Mircea Caprioru <[email protected]>---
Changelog v2:
- modified SPDX license to GPL-2.0 OR BSD-2-Clause
- added regex for a range from 0 to 15
- added minimum and maximum constraints for reg property
- set type and range of values for adi,reference-select property
- used items for diff-channels property
- set bipolar, adi,buffered-positive and negative to type: booleanChangelog v3:
- moved adi,buffered-positive and negative properties to own commitChangelog v4:
- removed old txt dt-bindingQuoted 7 lines
Quoted 5 lines
.../bindings/iio/adc/adi,ad7124.txt | 75 --------- .../bindings/iio/adc/adi,ad7124.yaml | 144 ++++++++++++++++++ 2 files changed, 144 insertions(+), 75 deletions(-) delete mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7124.txt create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7124.yamlReviewed-by Rob Herring <[email protected]>
Quoted 8 lines
Something a bit odd happened when trying to apply this, so I ended up doing it rather manually.
error: cannot convert from y to UTF-8
fatal: could not parse patchAnyhow, I think it's fine now, but would welcome any suggestion on what causes that one? Patch was perfectly happy with it.
Looks like an error in the mail header:
Content-Type: text/plain; charset="y"
Rob
PATCH v4 5/5 dt-bindings: iio: adc: Add buffered input property
In reply to Mircea CaprioruThis patch adds the buffered mode device tree property for positive and negative inputs. Each option can be enabled independently.
In buffered mode, the input channel feeds into a high impedance input stage of the buffer amplifier. Therefore, the input can tolerate significant source impedances and is tailored for direct connection to external resistive type sensors such as strain gages or RTDs.
---
Changelog v3:
- added this separate commit for adi,buffered-positive and negative properties
Changelog v4:
- nothing changed here
.../devicetree/bindings/iio/adc/adi,ad7124.yaml | 11 +++++++++++ 1 file changed, 11 insertions(+)
Documentation/devicetree/bindings/iio/adc/adi,ad7124.yaml +11 -0
@@ -100,6 +100,14 @@ patternProperties: description: see Documentation/devicetree/bindings/iio/adc/adc.txt type: boolean + adi,buffered-positive: + description: Enable buffered mode for positive input. + type: boolean + + adi,buffered-negative: + description: Enable buffered mode for negative input. + type: boolean + required: - reg - diff-channels
@@ -123,6 +131,7 @@ examples: reg = <0>; diff-channels = <0 1>; adi,reference-select = <0>; + adi,buffered-positive; }; channel@1 {
@@ -130,6 +139,8 @@ examples: bipolar; diff-channels = <2 3>; adi,reference-select = <0>; + adi,buffered-positive; + adi,buffered-negative; }; channel@2 {
Signature · 1 line
2.17.1
Re: [PATCH V4 5/5] dt-bindings: iio: adc: Add buffered input property
Quoted 16 lines · Mircea Caprioru
This patch adds the buffered mode device tree property for positive and negative inputs. Each option can be enabled independently.
In buffered mode, the input channel feeds into a high impedance input stage of the buffer amplifier. Therefore, the input can tolerate significant source impedances and is tailored for direct connection to external resistive type sensors such as strain gages or RTDs.
Signed-off-by Mircea Caprioru <[email protected]>---
Changelog v3:
- added this separate commit for adi,buffered-positive and negative properties
Quoted 5 lines
Changelog v4:
- nothing changed here.../devicetree/bindings/iio/adc/adi,ad7124.yaml | 11 +++++++++++ 1 file changed, 11 insertions(+)
Jonathan Cameron
maintainerRe: [PATCH V4 5/5] dt-bindings: iio: adc: Add buffered input property
Quoted 18 lines · On Wed, 26 Jun 2019 08:45:01 -0600 Rob Herring <[email protected]> wrote:
Quoted 16 lines · Mircea Caprioru
This patch adds the buffered mode device tree property for positive and negative inputs. Each option can be enabled independently.
In buffered mode, the input channel feeds into a high impedance input stage of the buffer amplifier. Therefore, the input can tolerate significant source impedances and is tailored for direct connection to external resistive type sensors such as strain gages or RTDs.
Signed-off-by Mircea Caprioru <[email protected]>---
Changelog v3:
- added this separate commit for adi,buffered-positive and negative properties
Quoted 7 lines
Quoted 5 lines
Changelog v4:
- nothing changed here.../devicetree/bindings/iio/adc/adi,ad7124.yaml | 11 +++++++++++ 1 file changed, 11 insertions(+)Reviewed-by Rob Herring <[email protected]>
Applied to the togreg branch of iio.git and pushed out as testing.
thanks,
Jonathan
Jonathan Cameron
maintainerQuoted 8 lines · On Tue, 25 Jun 2019 11:11:24 +0300 Mircea Caprioru…
The driver limits the user to use only 4/8 differential inputs, but this device has the option to use pseudo-differential channels. This will increase the number of channels to be equal with the number of inputs so 8 channels for ad7124-4 and 16 for ad7124-8.
This patch removes the check between channel nodes and
num_inputsvalue.Signed-off-by Mircea Caprioru <[email protected]>
Applied to the togreg branch of iio.git and pushed out as testing for the autobuilders to play with it.
Thanks,
Jonathan
Quoted 32 lines
---
Changelog v2:
- nothing changed hereChangelog v3:
- nothing changed hereChangelog v4:
- nothing changed heredrivers/iio/adc/ad7124.c | 7 ------- 1 file changed, 7 deletions(-)drivers/iio/adc/ad7124.c +0
-7@@ -462,13 +462,6 @@ static int ad7124_of_parse_channel_config(struct iio_dev *indio_dev,if (ret) goto err; -if (ain[0 ] >= st->chip_info->num_inputs || - ain[1 ] >= st->chip_info->num_inputs) { -dev_err (indio_dev->dev.parent, -"Input pin number out of range.\n" ); - ret = -EINVAL ; - goto err; - } st->channel_config[channel].ain =AD7124_CHANNEL_AINP (ain[0 ]) |AD7124_CHANNEL_AINM (ain[1 ]); st->channel_config[channel].bipolar =