Skip to contentSkip to conversation

ARM: dts: exynos: Adjust buck[78] regulators to supported values on Odroid XU3 family

PATCH New Krzysztof Kozlowski 1 participant 2 messages Jun 29, 2019

Subsystems (2)
lore
Share & tools
lore

Krzysztof Kozlowski

author maintainer
#0 lore raw

PATCH 1/2 ARM: dts: exynos: Adjust buck[78] regulators to supported values on Odroid XU3 family

The datasheet of S2MPS11 PMIC is slightly non-consistent in buck[78] voltage regulators values.

1. The voltage tables for configuring their registers mention range of
voltages: 0.750 V to 3.55 V,
2. The constrains in electrical specifications say output voltage range to be different (buck7: 1.2 V to 1.5 V, buck8: 1.8 V to 2.1 V).

Adjust the ranges to match the electrical specifications to stay on the safe side. Also change the name of regulators to match reality. Anyway these regulators stay at default value so this should not have effect.

---
 arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
arch/arm/boot/dts/exynos5422-odroid-core.dtsi +5 -5
index 9843d21d6924..829147e320e0 100644
@@ -551,17 +551,17 @@
 			};
 
 			buck7_reg: BUCK7 {
-				regulator-name = "vdd_1.0v_ldo";
-				regulator-min-microvolt = <800000>;
+				regulator-name = "vdd_1.35v_ldo";
+				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1500000>;
 				regulator-always-on;
 				regulator-boot-on;
 			};
 
 			buck8_reg: BUCK8 {
-				regulator-name = "vdd_1.8v_ldo";
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <2000000>;
+				regulator-name = "vdd_2.0v_ldo";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <2100000>;
 				regulator-always-on;
 				regulator-boot-on;
 			};
Signature · 1 line
2.17.1
author maintainer
#1 lore raw

PATCH 2/2 ARM: dts: exynos: Adjust buck[78] regulators to supported values on Arndale Octa

The datasheet of S2MPS11 PMIC is slightly non-consistent in buck[78] voltage regulators values.

1. The voltage tables for configuring their registers mention range of
voltages: 0.750 V to 3.55 V,
2. The constrains in electrical specifications say output voltage range to be different (buck7: 1.2 V to 1.5 V, buck8: 1.8 V to 2.1 V).

Adjust the ranges to match the electrical specifications to stay on the safe side. Anyway these regulators stay at default value so this should not have effect.

---
 arch/arm/boot/dts/exynos5420-arndale-octa.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
arch/arm/boot/dts/exynos5420-arndale-octa.dts +3 -3
index ac7f2fa0ba22..592d7b45ecc8 100644
@@ -723,15 +723,15 @@
 
 			buck7_reg: BUCK7 {
 				regulator-name = "VIN_LLDO_1V4";
-				regulator-min-microvolt = <800000>;
+				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1500000>;
 				regulator-always-on;
 			};
 
 			buck8_reg: BUCK8 {
 				regulator-name = "VIN_MLDO_2V0";
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <2000000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <2100000>;
 				regulator-always-on;
 			};
 
Signature · 1 line
2.17.1