Conversion of panel bindings to DT schema

index 248141c3c7e3..0601a9e34703 100644
@@ -10,7 +10,7 @@ Required properties:
 - compatible: should be "arm,versatile-tft-panel"
 
 Required subnodes:
-- port: see display/panel/panel-common.txt, graph.txt
+- port: see display/panel/panel-common.yaml, graph.txt
 
 
 Example:

101 lines not on this page · raw message

149 lines not on this page · raw message

deleted file mode 100644
index e2e6867852b8..000000000000
@@ -1,4 +0,0 @@
-Common display properties
--------------------------
-
-- rotation:	Display rotation in degrees counter clockwise (0,90,180,270)

index b2b872c710f2..e11208fb7da8 100644
@@ -1,28 +1 @@
-Simple display panel
-====================
-
-panel node
-----------
-
-Required properties:
-- power-supply: See panel-common.txt
-
-Optional properties:
-- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
-- enable-gpios: GPIO pin to enable or disable the panel
-- backlight: phandle of the backlight device attached to the panel
-- no-hpd: This panel is supposed to communicate that it's ready via HPD
-  (hot plug detect) signal, but the signal isn't hooked up so we should
-  hardcode the max delay from the panel spec when powering up the panel.
-
-Example:
-
-	panel: panel {
-		compatible = "cptt,claa101wb01";
-		ddc-i2c-bus = <&panelddc>;
-
-		power-supply = <&vdd_pnl_reg>;
-		enable-gpios = <&gpio 90 0>;
-
-		backlight = <&backlight>;
-	};
+See panel-common.yaml in this directory.

deleted file mode 100644
index 6812280cb109..000000000000
@@ -1,26 +0,0 @@
-Ampire AM-480272H3TMQW-T01H 4.3" WQVGA TFT LCD panel
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
-
-Required properties:
-- compatible: should be "ampire,am-480272h3tmqw-t01h"
-
-Optional properties:
-- power-supply: regulator to provide the supply voltage
-- enable-gpios: GPIO pin to enable or disable the panel
-- backlight: phandle of the backlight device attached to the panel
-
-Optional nodes:
-- Video port for RGB input.
-
-Example:
-	panel_rgb: panel-rgb {
-		compatible = "ampire,am-480272h3tmqw-t01h";
-		enable-gpios = <&gpioa 8 1>;
-		port {
-			panel_in_rgb: endpoint {
-				remote-endpoint = <&controller_out_rgb>;
-			};
-		};
-	};

42 lines not on this page · raw message

deleted file mode 100644
index a30d63db3c8f..000000000000
@@ -1,9 +0,0 @@
-Armadeus ST0700 Adapt. A Santek ST0700I5Y-RBSLW 7.0" WVGA (800x480) TFT with
-an adapter board.
-
-Required properties:
-- compatible: "armadeus,st0700-adapt"
-- power-supply: see panel-common.txt
-
-Optional properties:
-- backlight: see panel-common.txt

new file mode 100644
index 000000000000..a6ade47066b3
@@ -0,0 +1,33 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/armadeus,st0700-adapt.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Armadeus ST0700 Adapter
+
+description:
+  A Santek ST0700I5Y-RBSLW 7.0" WVGA (800x480) TFT with an adapter board.
+
+maintainers:
+  - '"Sébastien Szymanski" <[email protected]>'
+  - Thierry Reding <[email protected]>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: armadeus,st0700-adapt
+
+  power-supply: true
+  backlight: true
+  port: true
+
+additionalProperties: false
+
+required:
+  - compatible
+  - power-supply
+
+...

deleted file mode 100644
index 35bc0c839f49..000000000000
@@ -1,12 +0,0 @@
-Banana Pi 7" (S070WV20-CT16) TFT LCD Panel
-
-Required properties:
-- compatible: should be "bananapi,s070wv20-ct16"
-- power-supply: see ./panel-common.txt
-
-Optional properties:
-- enable-gpios: see ./simple-panel.txt
-- backlight: see ./simple-panel.txt
-
-This binding is compatible with the simple-panel binding, which is specified
-in ./simple-panel.txt.

new file mode 100644
index 000000000000..bbf127fb28f7
@@ -0,0 +1,31 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/bananapi,s070wv20-ct16.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Banana Pi 7" (S070WV20-CT16) TFT LCD Panel
+
+maintainers:
+  - Chen-Yu Tsai <[email protected]>
+  - Thierry Reding <[email protected]>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: bananapi,s070wv20-ct16
+
+  power-supply: true
+  backlight: true
+  enable-gpios: true
+  port: true
+
+additionalProperties: false
+
+required:
+  - compatible
+  - power-supply
+
+...

deleted file mode 100644
index bf06bb025b08..000000000000
@@ -1,13 +0,0 @@
-DLC Display Co. DLC0700YZG-1 7.0" WSVGA TFT LCD panel
-
-Required properties:
-- compatible: should be "dlc,dlc0700yzg-1"
-- power-supply: See simple-panel.txt
-
-Optional properties:
-- reset-gpios: See panel-common.txt
-- enable-gpios: See simple-panel.txt
-- backlight: See simple-panel.txt
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.

new file mode 100644
index 000000000000..287e2feb6533
@@ -0,0 +1,31 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/dlc,dlc0700yzg-1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: DLC Display Co. DLC0700YZG-1 7.0" WSVGA TFT LCD panel
+
+maintainers:
+  - Philipp Zabel <[email protected]>
+  - Thierry Reding <[email protected]>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: dlc,dlc0700yzg-1
+
+  reset-gpios: true
+  enable-gpios: true
+  backlight: true
+  port: true
+
+additionalProperties: false
+
+required:
+  - compatible
+  - power-supply
+
+...

deleted file mode 100644
index 1639fb17a9f0..000000000000
@@ -1,14 +0,0 @@
-PDA 91-00156-A0 5.0" WVGA TFT LCD panel
-
-Required properties:
-- compatible: should be "pda,91-00156-a0"
-- power-supply: this panel requires a single power supply. A phandle to a
-regulator needs to be specified here. Compatible with panel-common binding which
-is specified in the panel-common.txt in this directory.
-- backlight: this panel's backlight is controlled by an external backlight
-controller. A phandle to this controller needs to be specified here.
-Compatible with panel-common binding which is specified in the panel-common.txt
-in this directory.
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.

new file mode 100644
index 000000000000..ccd3623b4955
@@ -0,0 +1,31 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/pda,91-00156-a0.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PDA 91-00156-A0 5.0" WVGA TFT LCD panel
+
+maintainers:
+  - Cristian Birsan <[email protected]>
+  - Thierry Reding <[email protected]>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: pda,91-00156-a0
+
+  power-supply: true
+  backlight: true
+  port: true
+
+additionalProperties: false
+
+required:
+  - compatible
+  - power-supply
+  - backlight
+
+...

deleted file mode 100644
index e9e19c059260..000000000000
@@ -1,49 +0,0 @@
-This binding covers the official 7" (800x480) Raspberry Pi touchscreen
-panel.
-
-This DSI panel contains:
-
-- TC358762 DSI->DPI bridge
-- Atmel microcontroller on I2C for power sequencing the DSI bridge and
-  controlling backlight
-- Touchscreen controller on I2C for touch input
-
-and this binding covers the DSI display parts but not its touch input.
-
-Required properties:
-- compatible:	Must be "raspberrypi,7inch-touchscreen-panel"
-- reg:		Must be "45"
-- port:		See panel-common.txt
-
-Example:
-
-dsi1: dsi@7e700000 {
-	#address-cells = <1>;
-	#size-cells = <0>;
-	<...>
-
-	port {
-		dsi_out_port: endpoint {
-			remote-endpoint = <&panel_dsi_port>;
-		};
-	};
-};
-
-i2c_dsi: i2c {
-	compatible = "i2c-gpio";
-	#address-cells = <1>;
-	#size-cells = <0>;
-	gpios = <&gpio 28 0
-		 &gpio 29 0>;
-
-	lcd@45 {
-		compatible = "raspberrypi,7inch-touchscreen-panel";
-		reg = <0x45>;
-
-		port {
-			panel_dsi_port: endpoint {
-				remote-endpoint = <&dsi_out_port>;
-			};
-		};
-	};
-};

71 lines not on this page · raw message

deleted file mode 100644
index dfb572f085eb..000000000000
@@ -1,15 +0,0 @@
-TFC S9700RTWV43TR-01B 7" Three Five Corp 800x480 LCD panel with
-resistive touch
-
-The panel is found on TI AM335x-evm.
-
-Required properties:
-- compatible: should be "tfc,s9700rtwv43tr-01b"
-- power-supply: See panel-common.txt
-
-Optional properties:
-- enable-gpios: GPIO pin to enable or disable the panel, if there is one
-- backlight: phandle of the backlight device attached to the panel
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.

new file mode 100644
index 000000000000..9e5994417c12
@@ -0,0 +1,33 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/tfc,s9700rtwv43tr-01b.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TFC S9700RTWV43TR-01B 7" Three Five Corp 800x480 LCD panel with resistive touch
+
+maintainers:
+  - Jyri Sarha <[email protected]>
+  - Thierry Reding <[email protected]>
+
+description: |+
+  The panel is found on TI AM335x-evm.
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: tfc,s9700rtwv43tr-01b
+
+  enable-gpios: true
+  backlight: true
+  port: true
+
+additionalProperties: false
+
+required:
+  - compatible
+  - power-supply
+
+...

new file mode 100644
index 000000000000..d0083301acbe
@@ -0,0 +1,107 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/lvds.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: LVDS Display Panel
+
+maintainers:
+  - Laurent Pinchart <[email protected]>
+  - Thierry Reding <[email protected]>
+
+description: |+
+  LVDS is a physical layer specification defined in ANSI/TIA/EIA-644-A. Multiple
+  incompatible data link layers have been used over time to transmit image data
+  to LVDS panels. This bindings supports display panels compatible with the
+  following specifications.
+
+  [JEIDA] "Digital Interface Standards for Monitor", JEIDA-59-1999, February
+  1999 (Version 1.0), Japan Electronic Industry Development Association (JEIDA)
+  [LDI] "Open LVDS Display Interface", May 1999 (Version 0.95), National
+  Semiconductor
+  [VESA] "VESA Notebook Panel Standard", October 2007 (Version 1.0), Video
+  Electronics Standards Association (VESA)
+
+  Device compatible with those specifications have been marketed under the
+  FPD-Link and FlatLink brands.
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    contains:
+      const: panel-lvds
+    description:
+      Shall contain "panel-lvds" in addition to a mandatory panel-specific
+      compatible string defined in individual panel bindings. The "panel-lvds"
+      value shall never be used on its own.
+
+  data-mapping:
+    enum:
+      - jeida-18
+      - jeida-24
+      - vesa-24
+    description: |
+      The color signals mapping order.
+
+      LVDS data mappings are defined as follows.
+
+      - "jeida-18" - 18-bit data mapping compatible with the [JEIDA], [LDI] and
+        [VESA] specifications. Data are transferred as follows on 3 LVDS lanes.
+
+      Slot	    0       1       2       3       4       5       6
+            ________________                         _________________
+      Clock	                \_______________________/
+              ______  ______  ______  ______  ______  ______  ______
+      DATA0	><__G0__><__R5__><__R4__><__R3__><__R2__><__R1__><__R0__><
+      DATA1	><__B1__><__B0__><__G5__><__G4__><__G3__><__G2__><__G1__><
+      DATA2	><_CTL2_><_CTL1_><_CTL0_><__B5__><__B4__><__B3__><__B2__><
+
+      - "jeida-24" - 24-bit data mapping compatible with the [DSIM] and [LDI]
+        specifications. Data are transferred as follows on 4 LVDS lanes.
+
+      Slot	    0       1       2       3       4       5       6
+            ________________                         _________________
+      Clock	                \_______________________/
+              ______  ______  ______  ______  ______  ______  ______
+      DATA0	><__G2__><__R7__><__R6__><__R5__><__R4__><__R3__><__R2__><
+      DATA1	><__B3__><__B2__><__G7__><__G6__><__G5__><__G4__><__G3__><
+      DATA2	><_CTL2_><_CTL1_><_CTL0_><__B7__><__B6__><__B5__><__B4__><
+      DATA3	><_CTL3_><__B1__><__B0__><__G1__><__G0__><__R1__><__R0__><
+
+      - "vesa-24" - 24-bit data mapping compatible with the [VESA] specification.
+        Data are transferred as follows on 4 LVDS lanes.
+
+      Slot	    0       1       2       3       4       5       6
+            ________________                         _________________
+      Clock	                \_______________________/
+              ______  ______  ______  ______  ______  ______  ______
+      DATA0	><__G0__><__R5__><__R4__><__R3__><__R2__><__R1__><__R0__><
+      DATA1	><__B1__><__B0__><__G5__><__G4__><__G3__><__G2__><__G1__><
+      DATA2	><_CTL2_><_CTL1_><_CTL0_><__B5__><__B4__><__B3__><__B2__><
+      DATA3	><_CTL3_><__B7__><__B6__><__G7__><__G6__><__R7__><__R6__><
+
+      Control signals are mapped as follows.
+
+      CTL0: HSync
+      CTL1: VSync
+      CTL2: Data Enable
+      CTL3: 0
+
+  data-mirror:
+    type: boolean
+    description:
+      If set, reverse the bit order described in the data mappings below on all
+      data lanes, transmitting bits for slots 6 to 0 instead of 0 to 6.
+
+required:
+  - compatible
+  - data-mapping
+  - width-mm
+  - height-mm
+  - panel-timing
+  - port
+
+...

121 lines not on this page · raw message

deleted file mode 100644
index e5ca4ccd55ed..000000000000
@@ -1,7 +0,0 @@
-Innolux Corporation 10.1" EE101IA-01D WXGA (1280x800) LVDS panel
-
-Required properties:
-- compatible: should be "innolux,ee101ia-01d"
-
-This binding is compatible with the lvds-panel binding, which is specified
-in panel-lvds.txt in this directory.

new file mode 100644
index 000000000000..a69681e724cb
@@ -0,0 +1,31 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/innolux,ee101ia-01d.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Innolux Corporation 10.1" EE101IA-01D WXGA (1280x800) LVDS panel
+
+maintainers:
+  - Heiko Stuebner <[email protected]>
+  - Thierry Reding <[email protected]>
+
+allOf:
+  - $ref: lvds.yaml#
+
+properties:
+  compatible:
+    items:
+      - const: innolux,ee101ia-01d
+      - {} # panel-lvds, but not listed here to avoid false select
+
+  backlight: true
+  enable-gpios: true
+  power-supply: true
+  width-mm: true
+  height-mm: true
+  panel-timing: true
+  port: true
+
+additionalProperties: false
+...

deleted file mode 100644
index ced0121aed7d..000000000000
@@ -1,47 +0,0 @@
-Mitsubishi AA204XD12 LVDS Display Panel
-=======================================
-
-The AA104XD12 is a 10.4" XGA TFT-LCD display panel.
-
-These DT bindings follow the LVDS panel bindings defined in panel-lvds.txt
-with the following device-specific properties.
-
-
-Required properties:
-
-- compatible: Shall contain "mitsubishi,aa121td01" and "panel-lvds", in that
-  order.
-- vcc-supply: Reference to the regulator powering the panel VCC pins.
-
-
-Example
--------
-
-panel {
-	compatible = "mitsubishi,aa104xd12", "panel-lvds";
-	vcc-supply = <&vcc_3v3>;
-
-	width-mm = <210>;
-	height-mm = <158>;
-
-	data-mapping = "jeida-24";
-
-	panel-timing {
-		/* 1024x768 @65Hz */
-		clock-frequency = <65000000>;
-		hactive = <1024>;
-		vactive = <768>;
-		hsync-len = <136>;
-		hfront-porch = <20>;
-		hback-porch = <160>;
-		vfront-porch = <3>;
-		vback-porch = <29>;
-		vsync-len = <6>;
-	};
-
-	port {
-		panel_in: endpoint {
-			remote-endpoint = <&lvds_encoder>;
-		};
-	};
-};

75 lines not on this page · raw message

deleted file mode 100644
index d6e1097504fe..000000000000
@@ -1,47 +0,0 @@
-Mitsubishi AA121TD01 LVDS Display Panel
-=======================================
-
-The AA121TD01 is a 12.1" WXGA TFT-LCD display panel.
-
-These DT bindings follow the LVDS panel bindings defined in panel-lvds.txt
-with the following device-specific properties.
-
-
-Required properties:
-
-- compatible: Shall contain "mitsubishi,aa121td01" and "panel-lvds", in that
-  order.
-- vcc-supply: Reference to the regulator powering the panel VCC pins.
-
-
-Example
--------
-
-panel {
-	compatible = "mitsubishi,aa121td01", "panel-lvds";
-	vcc-supply = <&vcc_3v3>;
-
-	width-mm = <261>;
-	height-mm = <163>;
-
-	data-mapping = "jeida-24";
-
-	panel-timing {
-		/* 1280x800 @60Hz */
-		clock-frequency = <71000000>;
-		hactive = <1280>;
-		vactive = <800>;
-		hsync-len = <70>;
-		hfront-porch = <20>;
-		hback-porch = <70>;
-		vsync-len = <5>;
-		vfront-porch = <3>;
-		vback-porch = <15>;
-	};
-
-	port {
-		panel_in: endpoint {
-			remote-endpoint = <&lvds_encoder>;
-		};
-	};
-};

74 lines not on this page · raw message

deleted file mode 100644
index d06644b555bd..000000000000
@@ -1,41 +0,0 @@
-Solomon Goldentek Display GKTW70SDAE4SE LVDS Display Panel
-==========================================================
-
-The GKTW70SDAE4SE is a 7" WVGA TFT-LCD display panel.
-
-These DT bindings follow the LVDS panel bindings defined in panel-lvds.txt
-with the following device-specific properties.
-
-Required properties:
-
-- compatible: Shall contain "sgd,gktw70sdae4se" and "panel-lvds", in that order.
-
-Example
--------
-
-panel {
-	compatible = "sgd,gktw70sdae4se", "panel-lvds";
-
-	width-mm = <153>;
-	height-mm = <86>;
-
-	data-mapping = "jeida-18";
-
-	panel-timing {
-		clock-frequency = <32000000>;
-		hactive = <800>;
-		vactive = <480>;
-		hback-porch = <39>;
-		hfront-porch = <39>;
-		vback-porch = <29>;
-		vfront-porch = <13>;
-		hsync-len = <47>;
-		vsync-len = <2>;
-	};
-
-	port {
-		panel_in: endpoint {
-			remote-endpoint = <&lvds_encoder>;
-		};
-	};
-};

68 lines not on this page · raw message