ARM: dts: import meerkat96 board support
Subsystems (3)
PATCH 1/2 ARM: dts: import meerkat96 board support
It imports device tree source of meerkat96 board from Linux Kernel.
--- arch/arm/dts/Makefile | 1 + arch/arm/dts/imx7d-meerkat96.dts | 375 +++++++++++++++++++++++++++++++ 2 files changed, 376 insertions(+) create mode 100644 arch/arm/dts/imx7d-meerkat96.dts
arch/arm/dts/Makefile +1 -0
@@ -598,6 +598,7 @@ dtb-$(CONFIG_MX7) += imx7d-sdb.dtb \ imx7-colibri-emmc.dtb \ imx7-colibri-rawnand.dtb \ imx7s-warp.dtb \ + imx7d-meerkat96.dtb \ imx7d-pico-pi.dtb \ imx7d-pico-hobbit.dtb
arch/arm/dts/imx7d-meerkat96.dts new file +375 -0
375 lines not on this page · raw message
Signature · 1 line
2.18.0
PATCH 2/2 Add i.MX7D based Meerkat96 board support
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of 96Boards community and complies with all Consumer Edition board specifications.
https://www.novtech.com/products/meerkat96.html
https://www.96boards.org/product/imx7-96/
The initial supported/tested devices include:
- Debug serial
- SD
- USB Host (with Ethernet)
With these support, it's good enough for loading Linux Kernel from SD or Ethernet over USB.
--- arch/arm/mach-imx/mx7/Kconfig | 10 +++ board/novtech/meerkat96/Kconfig | 12 +++ board/novtech/meerkat96/MAINTAINERS | 6 ++ board/novtech/meerkat96/Makefile | 1 + board/novtech/meerkat96/README | 18 ++++ board/novtech/meerkat96/imximage.cfg | 127 +++++++++++++++++++++++++++ board/novtech/meerkat96/meerkat96.c | 71 +++++++++++++++ configs/meerkat96_defconfig | 52 +++++++++++ include/configs/meerkat96.h | 48 ++++++++++ 9 files changed, 345 insertions(+) create mode 100644 board/novtech/meerkat96/Kconfig create mode 100644 board/novtech/meerkat96/MAINTAINERS create mode 100644 board/novtech/meerkat96/Makefile create mode 100644 board/novtech/meerkat96/README create mode 100644 board/novtech/meerkat96/imximage.cfg create mode 100644 board/novtech/meerkat96/meerkat96.c create mode 100644 configs/meerkat96_defconfig create mode 100644 include/configs/meerkat96.h
arch/arm/mach-imx/mx7/Kconfig +10 -0
@@ -28,6 +28,15 @@ config TARGET_CL_SOM_IMX7 select SUPPORT_SPL imply CMD_DM +config TARGET_MEERKAT96 + bool "NovTech Meerkat96 board" + select BOARD_LATE_INIT + select DM + select DM_SERIAL + select DM_THERMAL + select MX7D + imply CMD_DM + config TARGET_MX7DSABRESD bool "mx7dsabresd" select BOARD_LATE_INIT
@@ -67,6 +76,7 @@ config SYS_SOC source "board/compulab/cl-som-imx7/Kconfig" source "board/freescale/mx7dsabresd/Kconfig" +source "board/novtech/meerkat96/Kconfig" source "board/technexion/pico-imx7d/Kconfig" source "board/toradex/colibri_imx7/Kconfig" source "board/warp7/Kconfig"
board/novtech/meerkat96/Kconfig new file +12 -0
@@ -0,0 +1,12 @@ +if TARGET_MEERKAT96 + +config SYS_BOARD + default "meerkat96" + +config SYS_VENDOR + default "novtech" + +config SYS_CONFIG_NAME + default "meerkat96" + +endif
board/novtech/meerkat96/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@ +MEERKAT96 BOARD +M: Shawn Guo <[email protected]> +S: Maintained +F: board/novtech/meerkat96 +F: include/configs/meerkat96.h +F: configs/meerkat96_defconfig
board/novtech/meerkat96/Makefile new file +1 -0
@@ -0,0 +1 @@ +obj-y := meerkat96.o
board/novtech/meerkat96/README new file +18 -0
@@ -0,0 +1,18 @@ +* Build U-Boot for Meerkat96 board + + $ make mrproper + $ make meerkat96_defconfig + $ make + + It will generate the U-Boot binary called u-boot-dtb.imx + +* Install U-Boot to MicroSD card + + Plug MicroSD card to a Linux machine (with card reader), find the + device name and replace sd[x] with the name in the following command. + + $ sudo dd if=u-boot-dtb.imx of=/dev/sd[x] bs=512 seek=2 + + It will install U-Boot to MicroSD card at 1KiB offset. Insert the + card to Meerkat96 MicroSD slot, power up the board, and U-Boot should + boot from the card.
board/novtech/meerkat96/imximage.cfg new file +127 -0
127 lines not on this page · raw message
board/novtech/meerkat96/meerkat96.c new file +71 -0
71 lines not on this page · raw message
configs/meerkat96_defconfig new file +52 -0
52 lines not on this page · raw message
include/configs/meerkat96.h new file +48 -0
48 lines not on this page · raw message
Signature · 1 line
2.18.0
PATCH 2/2 Add i.MX7D based Meerkat96 board support
Quoted 489 lines
Subject: [PATCH 2/2] Add i.MX7D based Meerkat96 board support
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of 96Boards community and complies with all Consumer Edition board specifications.
https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fwww.
novtech.com%2Fproducts%2Fmeerkat96.html&data=02%7C01%7Cpeng. fan%40nxp.com%7C176214b98ffa4e56554d08d702db2627%7C686ea1d3bc2 b4c6fa92cd99c5c301635%7C0%7C0%7C636981012574168813&sdata= 0GHIrcX%2BUQuG6O%2Fnnk8VtmAvGpD6VHBkTmfBP%2F3drgM%3D&r eserved=0
https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fwww.
96boards.org%2Fproduct%2Fimx7-96%2F&data=02%7C01%7Cpeng.fan %40nxp.com%7C176214b98ffa4e56554d08d702db2627%7C686ea1d3bc2b4c 6fa92cd99c5c301635%7C0%7C0%7C636981012574168813&sdata=Y15J bYp3e6E2hojGgO2NiW5ZQ5QLOY4gW03ewuvdB4g%3D&reserved=0The initial supported/tested devices include:
- Debug serial
- SD
- USB Host (with Ethernet)With these support, it's good enough for loading Linux Kernel from SD or Ethernet over USB.
Signed-off-by Shawn Guo <[email protected]>--- arch/arm/mach-imx/mx7/Kconfig | 10 +++ board/novtech/meerkat96/Kconfig | 12 +++ board/novtech/meerkat96/MAINTAINERS | 6 ++ board/novtech/meerkat96/Makefile | 1 + board/novtech/meerkat96/README | 18 ++++ board/novtech/meerkat96/imximage.cfg | 127 +++++++++++++++++++++++++++ board/novtech/meerkat96/meerkat96.c | 71 +++++++++++++++ configs/meerkat96_defconfig | 52 +++++++++++ include/configs/meerkat96.h | 48 ++++++++++ 9 files changed, 345 insertions(+) create mode 100644 board/novtech/meerkat96/Kconfig create mode 100644 board/novtech/meerkat96/MAINTAINERS create mode 100644 board/novtech/meerkat96/Makefile create mode 100644 board/novtech/meerkat96/README create mode 100644 board/novtech/meerkat96/imximage.cfg create mode 100644 board/novtech/meerkat96/meerkat96.c create mode 100644 configs/meerkat96_defconfig create mode 100644
include/configs/meerkat96.h(quoted diff) +0
-0b/arch/arm/mach-imx/mx7/Kconfig index
232f33285d40..286d36589d0b100644arch/arm/mach-imx/mx7/Kconfig +10
-0@@ -28,6 +28,15 @@ config TARGET_CL_SOM_IMX7 select SUPPORT_SPL imply CMD_DM +config TARGET_MEERKAT96 + bool "NovTech Meerkat96 board" + select BOARD_LATE_INIT + select DM + select DM_SERIAL + select DM_THERMAL + select MX7D + imply CMD_DM + config TARGET_MX7DSABRESD bool "mx7dsabresd" select BOARD_LATE_INIT@@ -67,6 +76,7 @@ config SYS_SOC source "board/compulab/cl-som-imx7/Kconfig" source "board/freescale/mx7dsabresd/Kconfig" +source "board/novtech/meerkat96/Kconfig" source "board/technexion/pico-imx7d/Kconfig" source "board/toradex/colibri_imx7/Kconfig" source "board/warp7/Kconfig"(quoted diff) +0
-0b/board/novtech/meerkat96/Kconfig new file mode 100644 index 000000000000..b0e46fcc1b3f
board/novtech/meerkat96/Kconfig new file +12
-0@@ -0,0 +1,12 @@ +if TARGET_MEERKAT96 + +config SYS_BOARD + default "meerkat96" + +config SYS_VENDOR + default "novtech" + +config SYS_CONFIG_NAME + default "meerkat96" + +endifboard/novtech/meerkat96/MAINTAINERS new file +6
-0@@ -0,0 +1,6 @@ +MEERKAT96 BOARD +M: Shawn Guo <[email protected]> +S: Maintained +F: board/novtech/meerkat96 +F: include/configs/meerkat96.h +F: configs/meerkat96_defconfigboard/novtech/meerkat96/Makefile new file +1
-0@@ -0,0 +1 @@ +obj-y := meerkat96.o(quoted diff) +0
-0b/board/novtech/meerkat96/README new file mode 100644 index 000000000000..bca2fad5a21f
board/novtech/meerkat96/README new file +18
-0@@ -0,0 +1,18 @@ +* Build U-Boot for Meerkat96 board + + $ make mrproper + $ make meerkat96_defconfig + $ make + + It will generate the U-Boot binary called u-boot-dtb.imx + +* Install U-Boot to MicroSD card + + Plug MicroSD card to a Linux machine (with card reader), find the + device name and replace sd[x] with the name in the following command. + + $ sudo dd if=u-boot-dtb.imx of=/dev/sd[x] bs=512 seek=2 + + It will install U-Boot to MicroSD card at 1KiB offset. Insert the + card to Meerkat96 MicroSD slot, power up the board, and U-Boot should + boot from the card.board/novtech/meerkat96/imximage.cfg new file +47
-0@@ -0,0 +1,127 @@ +/* + * Copyright (C) 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage */ + +#define __ASSEMBLY__ +#include <config.h> + +/* image version */ + +IMAGE_VERSION 2 + +/* + * Boot Device : sd + */ + +BOOT_FROM sd + +/* + * Secure boot support + */ +#ifdef CONFIG_SECURE_BOOT +CSF CONFIG_CSF_SIZE +#endif + +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ + +/* Enable OCRAM EPDC */ +DATA 4 0x30340004 0x4F400005 + +/* +=======================================================================
+======
+ * DDR Controller Registers
+ *
==============================================================
===============+ * Memory type: DDR3 + * Manufacturer: ISSI + * Device Part Number: IS43TR16256AL-125KBL + * Clock Freq.: 533MHz + * Density per CS in Gb: 4 + * Chip Selects used: 1 + * Number of Banks: 8 + * Row address: 15 + * Column address: 10 + * Data bus width: 16 + * ROW-BANK interleave: ENABLED+ *
+=============================================================
==========
+======
+ */board/novtech/meerkat96/imximage.cfg new file +35
-0+ +DATA 4 0x30391000 0x00000002 // deassert presetn +DATA 4 0x307A0000 0x01041001 // DDRC_MSTR +DATA 4 0x307A0064 0x00400046 // DDRC_RFSHTMG +DATA 4 0x307a0490 0x00000001 // DDRC_PCTRL_0 +DATA 4 0x307A00D4 0x00690000 // DDRC_INIT1 +DATA 4 0x307A00D0 0x00020083 // DDRC_INIT0 +DATA 4 0x307A00DC 0x09300004 // DDRC_INIT3 +DATA 4 0x307A00E0 0x04080000 // DDRC_INIT4 +DATA 4 0x307A00E4 0x00100004 // DDRC_INIT5 +DATA 4 0x307A00F4 0x0000033F // DDRC_RANKCTL +DATA 4 0x307A0100 0x090B1109 // DDRC_DRAMTMG0 +DATA 4 0x307A0104 0x0007020D // DDRC_DRAMTMG1 +DATA 4 0x307A0108 0x03040407 // DDRC_DRAMTMG2 +DATA 4 0x307A010C 0x00002006 // DDRC_DRAMTMG3 +DATA 4 0x307A0110 0x04020205 // DDRC_DRAMTMG4 +DATA 4 0x307A0114 0x03030202 // DDRC_DRAMTMG5 +DATA 4 0x307A0120 0x00000803 // DDRC_DRAMTMG8 +DATA 4 0x307A0180 0x00800020 // DDRC_ZQCTL0 +DATA 4 0x307A0190 0x02098204 // DDRC_DFITMG0 +DATA 4 0x307A0194 0x00030303 // DDRC_DFITMG1 +DATA 4 0x307A01A0 0x80400003 // DDRC_DFIUPD0 +DATA 4 0x307A01A4 0x00100020 // DDRC_DFIUPD1 +DATA 4 0x307A01A8 0x80100004 // DDRC_DFIUPD2 +DATA 4 0x307A0200 0x00000015 // DDRC_ADDRMAP0 +DATA 4 0x307A0204 0x00070707 // DDRC_ADDRMAP1 +DATA 4 0x307A0210 0x00000F0F // DDRC_ADDRMAP4 +DATA 4 0x307A0214 0x06060606 // DDRC_ADDRMAP5 +DATA 4 0x307A0218 0x0F060606 // DDRC_ADDRMAP6 +DATA 4 0x307A0240 0x06000604 // DDRC_ODTCFG +DATA 4 0x307A0244 0x00000001 // DDRC_ODTMAP + + +/* +=======================================================================
+======
+ * PHY Control Register
+ *
+=============================================================
==========
+======
+ */board/novtech/meerkat96/imximage.cfg new file +13
-0+ +DATA 4 0x30391000 0x00000000 // deassert presetn +DATA 4 0x30790000 0x17420F40 // DDR_PHY_PHY_CON0 +DATA 4 0x30790004 0x10210100 // DDR_PHY_PHY_CON1 +DATA 4 0x30790010 0x00060807 // DDR_PHY_PHY_CON4 +DATA 4 0x307900B0 0x1010007E // DDR_PHY_MDLL_CON0 +DATA 4 0x3079009C 0x00000D6E // DDR_PHY_DRVDS_CON0 +DATA 4 0x30790030 0x08080808 // DDR_PHY_OFFSET_WR_CON0 +DATA 4 0x30790020 0x08080808 // DDR_PHY_OFFSET_RD_CON0 +DATA 4 0x30790050 0x01000010 // DDR_PHY_OFFSETD_CON0 +DATA 4 0x30790050 0x00000010 // DDR_PHY_OFFSETD_CON0 +DATA 4 0x30790018 0x0000000F // DDR_PHY_LP_CON0 +DATA 4 0x307900C0 0x0E407304 // DDR_PHY_ZQ_CON0 - Start ManualZQ
board/novtech/meerkat96/imximage.cfg new file +3
-0+DATA 4 0x307900C0 0x0E447304 +DATA 4 0x307900C0 0x0E447306 +DATA 4 0x307900C0 0x0E447304 // <= NOTE: Depending on JTAG deviceused, may need ~ 7 us pause at this point.
+DATA 40x307900C00x0E407304//DDR_PHY_ZQ_CON0- End Manual
ZQboard/novtech/meerkat96/imximage.cfg new file +4
-0+ + +/* +=======================================================================
+======
+ * Final Initialization start sequence
+ *
+=============================================================
==========
+======
+ */board/novtech/meerkat96/imximage.cfg new file +3
-0+ +DATA 4 0x30384130 0x00000000 // Disable Clock +DATA 4 0x30340020 0x00000178 // IOMUX_GRP_GRP8 - Start input toPHY
board/novtech/meerkat96/imximage.cfg new file +3
-0+DATA 4 0x30384130 0x00000002 // Enable Clock +/* <= NOTE: Depending on JTAG device used, may need ~ 250 us pause at +this point. */board/novtech/meerkat96/meerkat96.c new file +22
-0@@ -0,0 +1,71 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (C) 2019 Linaro Ltd. +* Copyright (C) 2016 NXP Semiconductors */ + +#include <asm/arch/clock.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/mx7-pins.h> +#include <asm/arch/sys_proto.h> +#include <asm/mach-imx/iomux-v3.h> +#include <asm/io.h> +#include <common.h> +#include <linux/sizes.h> + +DECLARE_GLOBAL_DATA_PTR ; + +#define UART_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | \ + PAD_CTL_PUS_PU100KOHM | PAD_CTL_HYS) + +static iomux_v3_cfg_t const meerkat96_pads[] = { +/* UART6 as debug serial */ + MX7D_PAD_SD1_CD_B__UART6_DCE_RX |
MUX_PAD_CTRL(UART_PAD_CTRL),board/novtech/meerkat96/meerkat96.c new file +1
-0+ MX7D_PAD_SD1_WP__UART6_DCE_TX |
MUX_PAD_CTRL(UART_PAD_CTRL),board/novtech/meerkat96/meerkat96.c new file +2
-0+/* WDOG1 for reset */ + MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B |
MUX_PAD_CTRL(NO_PAD_CTRL), };board/novtech/meerkat96/meerkat96.c new file +44
-0+ +int dram_init (void ) +{ + gd->ram_size =PHYS_SDRAM_SIZE ; + +return 0 ; +} + +int board_early_init_f (void ) +{ +imx_iomux_v3_setup_multiple_pads (meerkat96_pads, +ARRAY_SIZE (meerkat96_pads)); + +return 0 ; +} + +int board_init (void ) +{ +/* address of boot parameters */ + gd->bd->bi_boot_params =PHYS_SDRAM +0x100 ; + +return 0 ; +} + +int checkboard (void ) +{ +char *mode; + +if (IS_ENABLED (CONFIG_ARMV7_BOOT_SEC_DEFAULT )) + mode ="secure" ; +else + mode ="non-secure" ; + +printf ("Board: i.MX7D Meerkat96 in %s mode\n" , mode); + +return 0 ; +} + +int board_late_init (void ) +{ +set_wdog_reset ((struct wdog_regs *)WDOG1_BASE_ADDR ); + +return 0 ; +}configs/meerkat96_defconfig new renamed from configs/meerkat96_defconfig +0
-0file mode 100644 index 000000000000..a2b51946798c
configs/meerkat96_defconfig new file +11
-0@@ -0,0 +1,52 @@ +CONFIG_ARM=y +CONFIG_ARCH_MX7=y +CONFIG_SYS_TEXT_BASE=0x87800000 +CONFIG_SYS_MALLOC_F_LEN=0x4000 +CONFIG_TARGET_MEERKAT96=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_ARMV7_BOOT_SEC_DEFAULT=y +# CONFIG_ARMV7_VIRT is not set +CONFIG_IMX_RDC=y +CONFIG_IMX_BOOTAUX=y +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/novtech/meerkat96/imximage.cfg"
configs/meerkat96_defconfig new file +41
-0+CONFIG_BOUNCE_BUFFER=y +CONFIG_HUSH_PARSER=y +# CONFIG_CMD_BOOTD is not set +CONFIG_CMD_BOOTZ=y +# CONFIG_CMD_IMI is not set +# CONFIG_CMD_XIMG is not set +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_MMC=y +CONFIG_CMD_PART=y +CONFIG_CMD_USB=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_EXT4=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FS_GENERIC=y +CONFIG_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="imx7d-meerkat96" +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM_GPIO=y +CONFIG_MMC_BROKEN_CD=y +CONFIG_DM_MMC=y +CONFIG_FSL_ESDHC=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_IMX7=y +CONFIG_DM_PMIC=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_MXC_USB_OTG_HACTIVE=y +CONFIG_USB_HOST_ETHER=y +CONFIG_USB_ETHER_ASIX=y +CONFIG_USB_ETHER_ASIX88179=y +CONFIG_USB_ETHER_MCS7830=y +CONFIG_USB_ETHER_RTL8152=y +CONFIG_USB_ETHER_SMSC95XX=yinclude/configs/meerkat96.h new renamed from include/configs/meerkat96.h +0
-0file mode 100644 index 000000000000..d0450af9542f
include/configs/meerkat96.h new file +21
-0@@ -0,0 +1,48 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (C) 2019 Linaro Ltd. +* Copyright (C) 2016 NXP Semiconductors +* +* Configuration settings for Meerkat96 board. +*/ + +#ifndef __MEERKAT96_CONFIG_H +#define __MEERKAT96_CONFIG_H + +#include "mx7_common.h" +#include <imximage.h> + +#define PHYS_SDRAM_SIZE SZ_512M + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M) + +#define CONFIG_SYS_MEMTEST_START 0x80000000 +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x20000000)include/configs/meerkat96.h new file +25
-0+ +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR +#define CONFIG_SYS_HZ 1000 + +/* Physical Memory Map */ +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define +CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR +CONFIG_SYS_INIT_SP_OFFSET ) + +/* Environment configs */ +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_SYS_MMC_ENV_PART 0 +#define CONFIG_ENV_SIZE SZ_8K +#define CONFIG_ENV_OFFSET (8 * SZ_64K) + +/* USB configs */ +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI |
PORT_PTS_PTW)
include/configs/meerkat96.h
Quoted 2 lines
include/configs/meerkat96.h new file +2
-0+ +#endif
Quoted 2 lines
--
2.18.0
PATCH 2/2 Add i.MX7D based Meerkat96 board support
In reply to Shawn GuoHi Shawn,
Thanks for the patch!
Quoted 11 lines · Shawn Guo
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of 96Boards community and complies with all Consumer Edition board specifications.
https://www.novtech.com/products/meerkat96.html
https://www.96boards.org/product/imx7-96/The initial supported/tested devices include:
- Debug serial
- SD
- USB Host (with Ethernet)
While testing, I encountered below error when starting usb:
=> usb start
starting USB...
Bus usb at 30b10000: usb dr_mode not found
Error enabling VBUS supply
probe failed, error -38
Bus usb at 30b20000: data abort
pc : [<9ffaf574>] lr : [<9ffaf560>]
reloc pc : [<87828574>] lr : [<87828560>]
sp : 9df7d1b0 ip : 431bde82 fp : 9ff9dc8c
r10: 00000000 r9 : 9df84ed8 r8 : 00000000
r7 : 9df865d8 r6 : 9df86578 r5 : 9df87680 r4 : 00000080
r3 : 00000000 r2 : 0196f7b6 r1 : 31310000 r0 : 00000000
Flags: nZCv IRQs off FIQs off Mode SVC_32
Code: 18bd8010 e2841dc2 e2811031 e1a01801 (e5913234)
Resetting CPU ...
resetting ...
Did I miss anything? Sorry, don't have time to debug much...
Regards,
Mani
Quoted 439 lines
With these support, it's good enough for loading Linux Kernel from SD or Ethernet over USB.
Signed-off-by Shawn Guo <[email protected]>--- arch/arm/mach-imx/mx7/Kconfig | 10 +++ board/novtech/meerkat96/Kconfig | 12 +++ board/novtech/meerkat96/MAINTAINERS | 6 ++ board/novtech/meerkat96/Makefile | 1 + board/novtech/meerkat96/README | 18 ++++ board/novtech/meerkat96/imximage.cfg | 127 +++++++++++++++++++++++++++ board/novtech/meerkat96/meerkat96.c | 71 +++++++++++++++ configs/meerkat96_defconfig | 52 +++++++++++ include/configs/meerkat96.h | 48 ++++++++++ 9 files changed, 345 insertions(+) create mode 100644 board/novtech/meerkat96/Kconfig create mode 100644 board/novtech/meerkat96/MAINTAINERS create mode 100644 board/novtech/meerkat96/Makefile create mode 100644 board/novtech/meerkat96/README create mode 100644 board/novtech/meerkat96/imximage.cfg create mode 100644 board/novtech/meerkat96/meerkat96.c create mode 100644 configs/meerkat96_defconfig create mode 100644 include/configs/meerkat96.harch/arm/mach-imx/mx7/Kconfig +10
-0@@ -28,6 +28,15 @@ config TARGET_CL_SOM_IMX7 select SUPPORT_SPL imply CMD_DM +config TARGET_MEERKAT96 + bool "NovTech Meerkat96 board" + select BOARD_LATE_INIT + select DM + select DM_SERIAL + select DM_THERMAL + select MX7D + imply CMD_DM + config TARGET_MX7DSABRESD bool "mx7dsabresd" select BOARD_LATE_INIT@@ -67,6 +76,7 @@ config SYS_SOC source "board/compulab/cl-som-imx7/Kconfig" source "board/freescale/mx7dsabresd/Kconfig" +source "board/novtech/meerkat96/Kconfig" source "board/technexion/pico-imx7d/Kconfig" source "board/toradex/colibri_imx7/Kconfig" source "board/warp7/Kconfig"board/novtech/meerkat96/Kconfig new file +12
-0@@ -0,0 +1,12 @@ +if TARGET_MEERKAT96 + +config SYS_BOARD + default "meerkat96" + +config SYS_VENDOR + default "novtech" + +config SYS_CONFIG_NAME + default "meerkat96" + +endifboard/novtech/meerkat96/MAINTAINERS new file +6
-0@@ -0,0 +1,6 @@ +MEERKAT96 BOARD +M: Shawn Guo <[email protected]> +S: Maintained +F: board/novtech/meerkat96 +F: include/configs/meerkat96.h +F: configs/meerkat96_defconfigboard/novtech/meerkat96/Makefile new file +1
-0@@ -0,0 +1 @@ +obj-y := meerkat96.oboard/novtech/meerkat96/README new file +18
-0@@ -0,0 +1,18 @@ +* Build U-Boot for Meerkat96 board + + $ make mrproper + $ make meerkat96_defconfig + $ make + + It will generate the U-Boot binary called u-boot-dtb.imx + +* Install U-Boot to MicroSD card + + Plug MicroSD card to a Linux machine (with card reader), find the + device name and replace sd[x] with the name in the following command. + + $ sudo dd if=u-boot-dtb.imx of=/dev/sd[x] bs=512 seek=2 + + It will install U-Boot to MicroSD card at 1KiB offset. Insert the + card to Meerkat96 MicroSD slot, power up the board, and U-Boot should + boot from the card.board/novtech/meerkat96/imximage.cfg new file +127
-0@@ -0,0 +1,127 @@ +/* + * Copyright (C) 2014 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */ + +#define __ASSEMBLY__ +#include <config.h> + +/* image version */ + +IMAGE_VERSION 2 + +/* + * Boot Device : sd + */ + +BOOT_FROM sd + +/* + * Secure boot support + */ +#ifdef CONFIG_SECURE_BOOT +CSF CONFIG_CSF_SIZE +#endif + +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ + +/* Enable OCRAM EPDC */ +DATA 4 0x30340004 0x4F400005 + +/* ============================================================================= + * DDR Controller Registers + * ============================================================================= + * Memory type: DDR3 + * Manufacturer: ISSI + * Device Part Number: IS43TR16256AL-125KBL + * Clock Freq.: 533MHz + * Density per CS in Gb: 4 + * Chip Selects used: 1 + * Number of Banks: 8 + * Row address: 15 + * Column address: 10 + * Data bus width: 16 + * ROW-BANK interleave: ENABLED + * ============================================================================= + */ + +DATA 4 0x30391000 0x00000002 // deassert presetn +DATA 4 0x307A0000 0x01041001 // DDRC_MSTR +DATA 4 0x307A0064 0x00400046 // DDRC_RFSHTMG +DATA 4 0x307a0490 0x00000001 // DDRC_PCTRL_0 +DATA 4 0x307A00D4 0x00690000 // DDRC_INIT1 +DATA 4 0x307A00D0 0x00020083 // DDRC_INIT0 +DATA 4 0x307A00DC 0x09300004 // DDRC_INIT3 +DATA 4 0x307A00E0 0x04080000 // DDRC_INIT4 +DATA 4 0x307A00E4 0x00100004 // DDRC_INIT5 +DATA 4 0x307A00F4 0x0000033F // DDRC_RANKCTL +DATA 4 0x307A0100 0x090B1109 // DDRC_DRAMTMG0 +DATA 4 0x307A0104 0x0007020D // DDRC_DRAMTMG1 +DATA 4 0x307A0108 0x03040407 // DDRC_DRAMTMG2 +DATA 4 0x307A010C 0x00002006 // DDRC_DRAMTMG3 +DATA 4 0x307A0110 0x04020205 // DDRC_DRAMTMG4 +DATA 4 0x307A0114 0x03030202 // DDRC_DRAMTMG5 +DATA 4 0x307A0120 0x00000803 // DDRC_DRAMTMG8 +DATA 4 0x307A0180 0x00800020 // DDRC_ZQCTL0 +DATA 4 0x307A0190 0x02098204 // DDRC_DFITMG0 +DATA 4 0x307A0194 0x00030303 // DDRC_DFITMG1 +DATA 4 0x307A01A0 0x80400003 // DDRC_DFIUPD0 +DATA 4 0x307A01A4 0x00100020 // DDRC_DFIUPD1 +DATA 4 0x307A01A8 0x80100004 // DDRC_DFIUPD2 +DATA 4 0x307A0200 0x00000015 // DDRC_ADDRMAP0 +DATA 4 0x307A0204 0x00070707 // DDRC_ADDRMAP1 +DATA 4 0x307A0210 0x00000F0F // DDRC_ADDRMAP4 +DATA 4 0x307A0214 0x06060606 // DDRC_ADDRMAP5 +DATA 4 0x307A0218 0x0F060606 // DDRC_ADDRMAP6 +DATA 4 0x307A0240 0x06000604 // DDRC_ODTCFG +DATA 4 0x307A0244 0x00000001 // DDRC_ODTMAP + + +/* ============================================================================= + * PHY Control Register + * ============================================================================= + */ + +DATA 4 0x30391000 0x00000000 // deassert presetn +DATA 4 0x30790000 0x17420F40 // DDR_PHY_PHY_CON0 +DATA 4 0x30790004 0x10210100 // DDR_PHY_PHY_CON1 +DATA 4 0x30790010 0x00060807 // DDR_PHY_PHY_CON4 +DATA 4 0x307900B0 0x1010007E // DDR_PHY_MDLL_CON0 +DATA 4 0x3079009C 0x00000D6E // DDR_PHY_DRVDS_CON0 +DATA 4 0x30790030 0x08080808 // DDR_PHY_OFFSET_WR_CON0 +DATA 4 0x30790020 0x08080808 // DDR_PHY_OFFSET_RD_CON0 +DATA 4 0x30790050 0x01000010 // DDR_PHY_OFFSETD_CON0 +DATA 4 0x30790050 0x00000010 // DDR_PHY_OFFSETD_CON0 +DATA 4 0x30790018 0x0000000F // DDR_PHY_LP_CON0 +DATA 4 0x307900C0 0x0E407304 // DDR_PHY_ZQ_CON0 - Start Manual ZQ +DATA 4 0x307900C0 0x0E447304 +DATA 4 0x307900C0 0x0E447306 +DATA 4 0x307900C0 0x0E447304 // <= NOTE: Depending on JTAG device used, may need ~ 7 us pause@this point. +DATA 4 0x307900C0 0x0E407304 // DDR_PHY_ZQ_CON0 - End Manual ZQ + + +/* ============================================================================= + * Final Initialization start sequence + * ============================================================================= + */ + +DATA 4 0x30384130 0x00000000 // Disable Clock +DATA 4 0x30340020 0x00000178 // IOMUX_GRP_GRP8 - Start input to PHY +DATA 4 0x30384130 0x00000002 // Enable Clock +/* <= NOTE: Depending on JTAG device used, may need ~ 250 us pause@this point. */board/novtech/meerkat96/meerkat96.c new file +71
-0@@ -0,0 +1,71 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (C) 2019 Linaro Ltd. +* Copyright (C) 2016 NXP Semiconductors +*/ + +#include <asm/arch/clock.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/mx7-pins.h> +#include <asm/arch/sys_proto.h> +#include <asm/mach-imx/iomux-v3.h> +#include <asm/io.h> +#include <common.h> +#include <linux/sizes.h> + +DECLARE_GLOBAL_DATA_PTR ; + +#define UART_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | \ + PAD_CTL_PUS_PU100KOHM | PAD_CTL_HYS) + +static iomux_v3_cfg_t const meerkat96_pads[] = { +/* UART6 as debug serial */ +MX7D_PAD_SD1_CD_B__UART6_DCE_RX |MUX_PAD_CTRL (UART_PAD_CTRL ), +MX7D_PAD_SD1_WP__UART6_DCE_TX |MUX_PAD_CTRL (UART_PAD_CTRL ), +/* WDOG1 for reset */ +MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B |MUX_PAD_CTRL (NO_PAD_CTRL ), +}; + +int dram_init (void ) +{ + gd->ram_size =PHYS_SDRAM_SIZE ; + +return 0 ; +} + +int board_early_init_f (void ) +{ +imx_iomux_v3_setup_multiple_pads (meerkat96_pads, +ARRAY_SIZE (meerkat96_pads)); + +return 0 ; +} + +int board_init (void ) +{ +/* address of boot parameters */ + gd->bd->bi_boot_params =PHYS_SDRAM +0x100 ; + +return 0 ; +} + +int checkboard (void ) +{ +char *mode; + +if (IS_ENABLED (CONFIG_ARMV7_BOOT_SEC_DEFAULT )) + mode ="secure" ; +else + mode ="non-secure" ; + +printf ("Board: i.MX7D Meerkat96 in %s mode\n" , mode); + +return 0 ; +} + +int board_late_init (void ) +{ +set_wdog_reset ((struct wdog_regs *)WDOG1_BASE_ADDR ); + +return 0 ; +}configs/meerkat96_defconfig new file +52
-0@@ -0,0 +1,52 @@ +CONFIG_ARM=y +CONFIG_ARCH_MX7=y +CONFIG_SYS_TEXT_BASE=0x87800000 +CONFIG_SYS_MALLOC_F_LEN=0x4000 +CONFIG_TARGET_MEERKAT96=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_ARMV7_BOOT_SEC_DEFAULT=y +# CONFIG_ARMV7_VIRT is not set +CONFIG_IMX_RDC=y +CONFIG_IMX_BOOTAUX=y +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/novtech/meerkat96/imximage.cfg" +CONFIG_BOUNCE_BUFFER=y +CONFIG_HUSH_PARSER=y +# CONFIG_CMD_BOOTD is not set +CONFIG_CMD_BOOTZ=y +# CONFIG_CMD_IMI is not set +# CONFIG_CMD_XIMG is not set +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_MMC=y +CONFIG_CMD_PART=y +CONFIG_CMD_USB=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_EXT4=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FS_GENERIC=y +CONFIG_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="imx7d-meerkat96" +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM_GPIO=y +CONFIG_MMC_BROKEN_CD=y +CONFIG_DM_MMC=y +CONFIG_FSL_ESDHC=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_IMX7=y +CONFIG_DM_PMIC=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_MXC_USB_OTG_HACTIVE=y +CONFIG_USB_HOST_ETHER=y +CONFIG_USB_ETHER_ASIX=y +CONFIG_USB_ETHER_ASIX88179=y +CONFIG_USB_ETHER_MCS7830=y +CONFIG_USB_ETHER_RTL8152=y +CONFIG_USB_ETHER_SMSC95XX=yinclude/configs/meerkat96.h new file +48
-0@@ -0,0 +1,48 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (C) 2019 Linaro Ltd. +* Copyright (C) 2016 NXP Semiconductors +* +* Configuration settings for Meerkat96 board. +*/ + +#ifndef __MEERKAT96_CONFIG_H +#define __MEERKAT96_CONFIG_H + +#include "mx7_common.h" +#include <imximage.h> + +#define PHYS_SDRAM_SIZE SZ_512M + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M) + +#define CONFIG_SYS_MEMTEST_START 0x80000000 +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x20000000) + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR +#define CONFIG_SYS_HZ 1000 + +/* Physical Memory Map */ +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +/* Environment configs */ +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_SYS_MMC_ENV_PART 0 +#define CONFIG_ENV_SIZE SZ_8K +#define CONFIG_ENV_OFFSET (8 * SZ_64K) + +/* USB configs */ +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) + +#endif Signature · 1 line
2.18.0
PATCH 2/2 Add i.MX7D based Meerkat96 board support
Quoted 17 lines · Manivannan Sadhasivam
Hi Shawn,
Thanks for the patch!
Quoted 11 lines · Shawn Guo
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of 96Boards community and complies with all Consumer Edition board specifications.
https://www.novtech.com/products/meerkat96.html
https://www.96boards.org/product/imx7-96/The initial supported/tested devices include:
- Debug serial
- SD
- USB Host (with Ethernet)
Quoted 7 lines
While testing, I encountered below error when starting usb:
=> usb start
starting USB...
Bus usb at30b10000: usbdr_modenot found Error enabling VBUS supply
probe failed, error -38
This is expected, as there are some properties missing from DT for USBOTG1, and I haven't put effort on it yet.
Quoted 8 lines
Bus usb at
30b20000: data abortpc : [<9ffaf574>] lr : [<9ffaf560>]reloc pc : [<87828574>] lr : [<87828560>]
sp :9df7d1b0ip :431bde82fp :9ff9dc8c
r10: 00000000 r9 :9df84ed8r8 : 00000000
r7 :9df865d8r6 :9df86578r5 :9df87680r4 : 00000080
r3 : 00000000 r2 :0196f7b6r1 : 31310000 r0 : 00000000
Flags: nZCv IRQs off FIQs off ModeSVC_32
Quoted 4 lines
Code: 18bd8010 e2841dc2 e2811031 e1a01801 (e5913234)Resetting CPU ...
resetting ...
It looks the exception comes from USBOTG2 which backs both Host ports on Meerkat96 board. I have never seen this in my testing. Do you have any USB device connected to the Host port, when this happens?
Quoted 2 lines
Did I miss anything? Sorry, don't have time to debug much...
If you can help me reproduce it on my end, I will debug it.
Shawn
PATCH 2/2 Add i.MX7D based Meerkat96 board support
Quoted 20 lines · Shawn Guo
Quoted 19 lines · Manivannan Sadhasivam
Hi Shawn,
Thanks for the patch!
Quoted 11 lines · Shawn Guo
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of 96Boards community and complies with all Consumer Edition board specifications.
https://www.novtech.com/products/meerkat96.html
https://www.96boards.org/product/imx7-96/The initial supported/tested devices include:
- Debug serial
- SD
- USB Host (with Ethernet)While testing, I encountered below error when starting usb:
Quoted 9 lines
Quoted 5 lines
=> usb start
starting USB...
Bus usb at30b10000: usbdr_modenot found Error enabling VBUS supply
probe failed, error -38This is expected, as there are some properties missing from DT for USBOTG1, and I haven't put effort on it yet.
This is fine.
Quoted 11 lines
Quoted 11 lines
Bus usb at
30b20000: data abortpc : [<9ffaf574>] lr : [<9ffaf560>]reloc pc : [<87828574>] lr : [<87828560>]
sp :9df7d1b0ip :431bde82fp :9ff9dc8c
r10: 00000000 r9 :9df84ed8r8 : 00000000
r7 :9df865d8r6 :9df86578r5 :9df87680r4 : 00000080
r3 : 00000000 r2 :0196f7b6r1 : 31310000 r0 : 00000000
Flags: nZCv IRQs off FIQs off ModeSVC_32Code: 18bd8010 e2841dc2 e2811031 e1a01801 (e5913234)Resetting CPU ...
Quoted 6 lines
Quoted 1 line
resetting ...
It looks the exception comes from USBOTG2 which backs both Host ports on Meerkat96 board. I have never seen this in my testing. Do you have any USB device connected to the Host port, when this happens?
Digged into this issue and found that the below commit is causing regression:
501547cec1 ("usb: ehci-mx6: Fix bus enumeration for DM case")
But as mentioned in the commit message, that commit was incomplete and this issue might be expected. Reverting the commit makes usb work again. And the reason you are not seeing this issue is, your tree might not be updated with mainline u-boot ;-)
Copied Marek who was the author of that commit.
With that, you can have my tested tag:
Thanks,
Mani
Quoted 6 lines
Quoted 2 lines
Did I miss anything? Sorry, don't have time to debug much...
If you can help me reproduce it on my end, I will debug it.
Shawn
PATCH 2/2 Add i.MX7D based Meerkat96 board support
Quoted 51 lines · Manivannan Sadhasivam
Quoted 20 lines · Shawn Guo
Quoted 19 lines · Manivannan Sadhasivam
Hi Shawn,
Thanks for the patch!
Quoted 11 lines · Shawn Guo
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of 96Boards community and complies with all Consumer Edition board specifications.
https://www.novtech.com/products/meerkat96.html
https://www.96boards.org/product/imx7-96/The initial supported/tested devices include:
- Debug serial
- SD
- USB Host (with Ethernet)While testing, I encountered below error when starting usb:
Quoted 9 lines
Quoted 5 lines
=> usb start
starting USB...
Bus usb at30b10000: usbdr_modenot found Error enabling VBUS supply
probe failed, error -38This is expected, as there are some properties missing from DT for USBOTG1, and I haven't put effort on it yet.
This is fine.
Quoted 11 lines
Quoted 11 lines
Bus usb at
30b20000: data abortpc : [<9ffaf574>] lr : [<9ffaf560>]reloc pc : [<87828574>] lr : [<87828560>]
sp :9df7d1b0ip :431bde82fp :9ff9dc8c
r10: 00000000 r9 :9df84ed8r8 : 00000000
r7 :9df865d8r6 :9df86578r5 :9df87680r4 : 00000080
r3 : 00000000 r2 :0196f7b6r1 : 31310000 r0 : 00000000
Flags: nZCv IRQs off FIQs off ModeSVC_32Code: 18bd8010 e2841dc2 e2811031 e1a01801 (e5913234)Resetting CPU ...
Quoted 6 lines
Quoted 1 line
resetting ...
It looks the exception comes from USBOTG2 which backs both Host ports on Meerkat96 board. I have never seen this in my testing. Do you have any USB device connected to the Host port, when this happens?
Quoted 8 lines
Digged into this issue and found that the below commit is causing regression:
501547cec1("usb: ehci-mx6: Fix bus enumeration for DM case")But as mentioned in the commit message, that commit was incomplete and this issue might be expected. Reverting the commit makes usb work again. And the reason you are not seeing this issue is, your tree might not be updated with mainline u-boot ;-)
Ah, that's the reason. I started my work on v2019.07-rc4 which doesn't include Marek's commit.
Shawn
PATCH 2/2 Add i.MX7D based Meerkat96 board support
In reply to Shawn GuoQuoted 11 lines
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of 96Boards community and complies with all Consumer Edition board specifications.
https://www.novtech.com/products/meerkat96.html
https://www.96boards.org/product/imx7-96/
The initial supported/tested devices include:
- Debug serial
- SD
- USB Host (with Ethernet)
With these support, it's good enough for loading Linux Kernel from SD or Ethernet over USB.
Quoted 3 lines
Signed-off-by Shawn Guo <[email protected]>Reviewed-by Peng Fan <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================