ASoC: Intel: Skylake: Recover BXT FW on DSP boot timeout error
Subsystems (3)
PATCH v2 1/1 ASoC: Intel: Skylake: Recover BXT FW on DSP boot timeout error
When DSP boots with timeout error try to reload firmware to keep best user expeirience.
--- sound/soc/intel/skylake/bxt-sst.c | 17 +++++++++++------ 1 file changed, 11 insertions(+), 6 deletions(-)
sound/soc/intel/skylake/bxt-sst.c +11 -6
@@ -455,13 +455,19 @@ static int bxt_set_dsp_D0(struct sst_dsp *ctx, unsigned int core_id)/* If core 1 was turned on for booting core 0, turn it off */ skl_dsp_core_power_down (ctx,SKL_DSP_CORE_MASK (1 ));if (ret ==0 ) { -dev_err (ctx->dev,"%s: DSP boot timeout\n" , __func__); -dev_err (ctx->dev,"Error code=0x%x: FW status=0x%x\n" , +dev_warn (ctx->dev, +"DSP boot timeout: Error code=0x%x: FW status=0x%x\n" ,sst_dsp_shim_read (ctx,BXT_ADSP_ERROR_CODE ),sst_dsp_shim_read (ctx,BXT_ADSP_FW_STATUS )); -dev_err (ctx->dev,"Failed to set core0 to D0 state\n" ); - ret = -EIO ; - goto err; +dev_warn (ctx->dev,"Reloading FW\n" ); + + ret =bxt_sst_init_fw (skl->dev, skl); +if (ret <0 ) { +dev_err (ctx->dev,"Reload fw failed: %d\n" , ret); +dev_err (ctx->dev,"Failed to set core0 to D0 state\n" ); + ret = -EIO ; + goto err; + } } }
@@ -486,7 +492,6 @@ static int bxt_set_dsp_D0(struct sst_dsp *ctx, unsigned int core_id)if (core_id ==SKL_DSP_CORE0_ID ) core_mask |=SKL_DSP_CORE_MASK (1 );skl_dsp_disable_core (ctx, core_mask); -return ret; }
Signature · 1 line
2.17.1
Cezary Rojewski
maintainerQuoted 25 lines · Pawel Harlozinski
When DSP boots with timeout error try to reload firmware to keep best user expeirience.
Signed-off-by Szymon Mielczarek <[email protected]>Signed-off-by Pawel Harlozinski <[email protected]>--- sound/soc/intel/skylake/bxt-sst.c | 17 +++++++++++------ 1 file changed, 11 insertions(+), 6 deletions(-)sound/soc/intel/skylake/bxt-sst.c +2
-4@@ -455,13 +455,19 @@ static int bxt_set_dsp_D0(struct sst_dsp *ctx, unsigned int core_id)/* If core 1 was turned on for booting core 0, turn it off */ skl_dsp_core_power_down (ctx,SKL_DSP_CORE_MASK (1 ));if (ret ==0 ) { -dev_err (ctx->dev,"%s: DSP boot timeout\n" , __func__); -dev_err (ctx->dev,"Error code=0x%x: FW status=0x%x\n" , +dev_warn (ctx->dev, +"DSP boot timeout: Error code=0x%x: FW status=0x%x\n" ,sst_dsp_shim_read (ctx,BXT_ADSP_ERROR_CODE ),sst_dsp_shim_read (ctx,BXT_ADSP_FW_STATUS )); -dev_err (ctx->dev,"Failed to set core0 to D0 state\n" ); - ret = -EIO ;
sound/soc/intel/skylake/bxt-sst.c static int bxt_set_dsp_D0(struct sst_dsp *ctx, unsigned int core_id) · line 470
Quoted 10 lines
sound/soc/intel/skylake/bxt-sst.c +9
-1- goto err; +dev_warn (ctx->dev,"Reloading FW\n" ); + + ret =bxt_sst_init_fw (skl->dev, skl); +if (ret <0 ) { +dev_err (ctx->dev,"Reload fw failed: %d\n" , ret); +dev_err (ctx->dev,"Failed to set core0 to D0 state\n" ); + ret = -EIO ; + goto err; + }
First, I'm sorry for the delay in response.
Now, where were we..
I'd combine there dump messages together - that is both dev_warns and both dev_errs. No need to spam 2 lines when there is single a message to communicate on each occasion.
Any reason for ignoring return code of bxt_sst_init_fw and overwriting it with -EIO? If the reason is _good_ then you can skip assignment an do if (bxt_sst_init_fw()) directly.
Apart from that, I'd like to see a FIXME comment or something of that sort. FW preparation is being updated in patches to come and if this fix cannot wait, it's good to mention it targets BXT platforms only, while SKL/ CNL descendants are left alone.
Czarek
Quoted 12 lines
sound/soc/intel/skylake/bxt-sst.c +0
-1} }@@ -486,7 +492,6 @@ static int bxt_set_dsp_D0(struct sst_dsp *ctx, unsigned int core_id)if (core_id ==SKL_DSP_CORE0_ID ) core_mask |=SKL_DSP_CORE_MASK (1 );skl_dsp_disable_core (ctx, core_mask); -return ret; }