Skip to contentSkip to conversation

ASoC: codecs: ad193x: Use regmap_multi_reg_write() when initializing

PATCH In review Codrin Ciubotariu 3 participants 3 messages Jul 10, 2019 – Jul 22, 2019

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ASoC: codecs: ad193x: Use regmap_multi_reg_write() when initializing

Using regmap_multi_reg_write() when we set the default values for our registers makes the code smaller and easier to read.

---
 sound/soc/codecs/ad193x.c | 19 +++++--------------
 1 file changed, 5 insertions(+), 14 deletions(-)
sound/soc/codecs/ad193x.c +5 -14
index 80dab5df9633..fb04c9379b71 100644
@@ -413,15 +413,10 @@ static struct snd_soc_dai_driver ad193x_no_adc_dai = {
 	.ops = &ad193x_dai_ops,
 };
 
-struct ad193x_reg_default {
-	unsigned int reg;
-	unsigned int val;
-};
-
 /* codec register values to set after reset */
 static void ad193x_reg_default_init(struct ad193x_priv *ad193x)
 {
-	const struct ad193x_reg_default reg_init[] = {
+	const struct reg_sequence reg_init[] = {
 		{  0, 0x99 },	/* PLL_CLK_CTRL0: pll input: mclki/xi 12.288Mhz */
 		{  1, 0x04 },	/* PLL_CLK_CTRL1: no on-chip Vref */
 		{  2, 0x40 },	/* DAC_CTRL0: TDM mode */
@@ -437,21 +432,17 @@ static void ad193x_reg_default_init(struct ad193x_priv *ad193x)
 		{ 12, 0x00 },	/* DAC_L4_VOL: no attenuation */
 		{ 13, 0x00 },	/* DAC_R4_VOL: no attenuation */
 	};
-	const struct ad193x_reg_default reg_adc_init[] = {
+	const struct reg_sequence reg_adc_init[] = {
 		{ 14, 0x03 },	/* ADC_CTRL0: high-pass filter enable */
 		{ 15, 0x43 },	/* ADC_CTRL1: sata delay=1, adc aux mode */
 		{ 16, 0x00 },	/* ADC_CTRL2: reset */
 	};
-	int i;
 
-	for (i = 0; i < ARRAY_SIZE(reg_init); i++)
-		regmap_write(ad193x->regmap, reg_init[i].reg, reg_init[i].val);
+	regmap_multi_reg_write(ad193x->regmap, reg_init, ARRAY_SIZE(reg_init));
 
 	if (ad193x_has_adc(ad193x)) {
-		for (i = 0; i < ARRAY_SIZE(reg_adc_init); i++) {
-			regmap_write(ad193x->regmap, reg_adc_init[i].reg,
-				     reg_adc_init[i].val);
-		}
+		regmap_multi_reg_write(ad193x->regmap, reg_adc_init,
+				       ARRAY_SIZE(reg_adc_init));
 	}
 }
 
Signature · 1 line
2.20.1
maintainer
#2 lore raw

Applied "ASoC: codecs: ad193x: Use regmap_multi_reg_write() when initializing" to the asoc tree

In reply to Codrin Ciubotariu

The patch

ASoC: codecs: ad193x: Use regmap_multi_reg_write() when initializing

has been applied to the asoc tree at

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-5.4

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

Thanks,
Mark

Quoted 1 line

From eaba5585944e6d692828bca701c9362f60172b8a Mon Sep 17 00:00:00 2001

From: Codrin Ciubotariu <[email protected]>
Date: Wed, 10 Jul 2019 13:51:19 +0300
Subject: [PATCH] ASoC: codecs: ad193x: Use regmap_multi_reg_write() when
initializing

Using regmap_multi_reg_write() when we set the default values for our registers makes the code smaller and easier to read.

---
 sound/soc/codecs/ad193x.c | 19 +++++--------------
 1 file changed, 5 insertions(+), 14 deletions(-)
sound/soc/codecs/ad193x.c +5 -14
index 80dab5df9633..fb04c9379b71 100644
@@ -413,15 +413,10 @@ static struct snd_soc_dai_driver ad193x_no_adc_dai = {
 	.ops = &ad193x_dai_ops,
 };
 
-struct ad193x_reg_default {
-	unsigned int reg;
-	unsigned int val;
-};
-
 /* codec register values to set after reset */
 static void ad193x_reg_default_init(struct ad193x_priv *ad193x)
 {
-	const struct ad193x_reg_default reg_init[] = {
+	const struct reg_sequence reg_init[] = {
 		{  0, 0x99 },	/* PLL_CLK_CTRL0: pll input: mclki/xi 12.288Mhz */
 		{  1, 0x04 },	/* PLL_CLK_CTRL1: no on-chip Vref */
 		{  2, 0x40 },	/* DAC_CTRL0: TDM mode */
@@ -437,21 +432,17 @@ static void ad193x_reg_default_init(struct ad193x_priv *ad193x)
 		{ 12, 0x00 },	/* DAC_L4_VOL: no attenuation */
 		{ 13, 0x00 },	/* DAC_R4_VOL: no attenuation */
 	};
-	const struct ad193x_reg_default reg_adc_init[] = {
+	const struct reg_sequence reg_adc_init[] = {
 		{ 14, 0x03 },	/* ADC_CTRL0: high-pass filter enable */
 		{ 15, 0x43 },	/* ADC_CTRL1: sata delay=1, adc aux mode */
 		{ 16, 0x00 },	/* ADC_CTRL2: reset */
 	};
-	int i;
 
-	for (i = 0; i < ARRAY_SIZE(reg_init); i++)
-		regmap_write(ad193x->regmap, reg_init[i].reg, reg_init[i].val);
+	regmap_multi_reg_write(ad193x->regmap, reg_init, ARRAY_SIZE(reg_init));
 
 	if (ad193x_has_adc(ad193x)) {
-		for (i = 0; i < ARRAY_SIZE(reg_adc_init); i++) {
-			regmap_write(ad193x->regmap, reg_adc_init[i].reg,
-				     reg_adc_init[i].val);
-		}
+		regmap_multi_reg_write(ad193x->regmap, reg_adc_init,
+				       ARRAY_SIZE(reg_adc_init));
 	}
 }
 
Signature · 1 line
2.20.1