Skip to contentSkip to conversation

ath10k: Do not send probe response template for mesh

PATCH New Sasha Levin 1 participant 53 messages Jul 15, 2019

Subsystems (17)
lore
Share & tools
lore

Sasha Levin

author maintainer
#0 lore raw

PATCH 1/53 ath10k: Do not send probe response template for mesh

From: Surabhi Vishnoi <[email protected]>

[ Upstream commit 97354f2c432788e3163134df6bb144f4b6289d87 ]

Currently mac80211 do not support probe response template for mesh point. When WMI_SERVICE_BEACON_OFFLOAD is enabled, host driver tries to configure probe response template for mesh, but it fails because the interface type is not NL80211_IFTYPE_AP but NL80211_IFTYPE_MESH_POINT.

To avoid this failure, skip sending probe response template to firmware for mesh point.

Tested HW: WCN3990/QCA6174/QCA9984

---
 drivers/net/wireless/ath/ath10k/mac.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/net/wireless/ath/ath10k/mac.c +4 -0
index 398068ad0b62..5a0138c1c045 100644
@@ -1502,6 +1502,10 @@ static int ath10k_mac_setup_prb_tmpl(struct ath10k_vif *arvif)
 	if (arvif->vdev_type != WMI_VDEV_TYPE_AP)
 		return 0;
 
+	 /* For mesh, probe response and beacon share the same template */
+	if (ieee80211_vif_is_mesh(vif))
+		return 0;
+
 	prb = ieee80211_proberesp_get(hw, vif);
 	if (!prb) {
 		ath10k_warn(ar, "failed to get probe resp template from mac80211\n");
Signature · 7 lines
2.20.1


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
author maintainer
#1 lore raw

PATCH 2/53 ath9k: Check for errors when reading SREV register

From: Tim Schumacher <[email protected]>

[ Upstream commit 2f90c7e5d09437a4d8d5546feaae9f1cf48cfbe1 ]

Right now, if an error is encountered during the SREV register read (i.e. an EIO in ath9k_regread()), that error code gets passed all the way to __ath9k_hw_init(), where it is visible during the "Chip rev not supported" message.

ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
ath: phy2: Mac Chip Rev 0x0f.3 is not supported by this driver
ath: phy2: Unable to initialize hardware; initialization status: -95
ath: phy2: Unable to initialize hardware; initialization status: -95
ath9k_htc: Failed to initialize the device

Check for -EIO explicitly in ath9k_hw_read_revisions() and return a boolean based on the success of the operation. Check for that in __ath9k_hw_init() and abort with a more debugging-friendly message if reading the revisions wasn't successful.

ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
ath: phy2: Failed to read SREV register
ath: phy2: Could not read hardware revision
ath: phy2: Unable to initialize hardware; initialization status: -95
ath: phy2: Unable to initialize hardware; initialization status: -95
ath9k_htc: Failed to initialize the device

This helps when debugging by directly showing the first point of failure and it could prevent possible errors if a 0x0f.3 revision is ever supported.

---
 drivers/net/wireless/ath/ath9k/hw.c | 32 +++++++++++++++++++++--------
 1 file changed, 23 insertions(+), 9 deletions(-)
drivers/net/wireless/ath/ath9k/hw.c +23 -9
index 4435c7bbb625..d50e2e8bd998 100644
@@ -250,8 +250,9 @@ void ath9k_hw_get_channel_centers(struct ath_hw *ah,
 /* Chip Revisions */
 /******************/
 
-static void ath9k_hw_read_revisions(struct ath_hw *ah)
+static bool ath9k_hw_read_revisions(struct ath_hw *ah)
 {
+	u32 srev;
 	u32 val;
 
 	if (ah->get_mac_revision)
@@ -267,25 +268,33 @@ static void ath9k_hw_read_revisions(struct ath_hw *ah)
 			val = REG_READ(ah, AR_SREV);
 			ah->hw_version.macRev = MS(val, AR_SREV_REVISION2);
 		}
-		return;
+		return true;
 	case AR9300_DEVID_AR9340:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9340;
-		return;
+		return true;
 	case AR9300_DEVID_QCA955X:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9550;
-		return;
+		return true;
 	case AR9300_DEVID_AR953X:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9531;
-		return;
+		return true;
 	case AR9300_DEVID_QCA956X:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9561;
-		return;
+		return true;
 	}
 
-	val = REG_READ(ah, AR_SREV) & AR_SREV_ID;
+	srev = REG_READ(ah, AR_SREV);
+
+	if (srev == -EIO) {
+		ath_err(ath9k_hw_common(ah),
+			"Failed to read SREV register");
+		return false;
+	}
+
+	val = srev & AR_SREV_ID;
 
 	if (val == 0xFF) {
-		val = REG_READ(ah, AR_SREV);
+		val = srev;
 		ah->hw_version.macVersion =
 			(val & AR_SREV_VERSION2) >> AR_SREV_TYPE2_S;
 		ah->hw_version.macRev = MS(val, AR_SREV_REVISION2);
@@ -304,6 +313,8 @@ static void ath9k_hw_read_revisions(struct ath_hw *ah)
 		if (ah->hw_version.macVersion == AR_SREV_VERSION_5416_PCIE)
 			ah->is_pciexpress = true;
 	}
+
+	return true;
 }
 
 /************************************/
@@ -556,7 +567,10 @@ static int __ath9k_hw_init(struct ath_hw *ah)
 	struct ath_common *common = ath9k_hw_common(ah);
 	int r = 0;
 
-	ath9k_hw_read_revisions(ah);
+	if (!ath9k_hw_read_revisions(ah)) {
+		ath_err(common, "Could not read hardware revisions");
+		return -EOPNOTSUPP;
+	}
 
 	switch (ah->hw_version.macVersion) {
 	case AR_SREV_VERSION_5416_PCI:
Signature · 1 line
2.20.1
author maintainer
#2 lore raw

PATCH 3/53 ath6kl: add some bounds checking

In reply to Sasha Levin

From: Dan Carpenter <[email protected]>

[ Upstream commit 5d6751eaff672ea77642e74e92e6c0ac7f9709ab ]

The "ev->traffic_class" and "reply->ac" variables come from the network and they're used as an offset into the wmi->stream_exist_for_ac[] array. Those variables are u8 so they can be 0-255 but the stream_exist_for_ac[] array only has WMM_NUM_AC (4) elements. We need to add a couple bounds checks to prevent array overflows.

I also modified one existing check from "if (traffic_class > 3) {" to "if (traffic_class >= WMM_NUM_AC) {" just to make them all consistent.

Fixes bdcd81707973 (" Add ath6kl cleaned up driver")
---
 drivers/net/wireless/ath/ath6kl/wmi.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)
drivers/net/wireless/ath/ath6kl/wmi.c +9 -1
index a5e1de75a4a3..b2ec254f154e 100644
@@ -1178,6 +1178,10 @@ static int ath6kl_wmi_pstream_timeout_event_rx(struct wmi *wmi, u8 *datap,
 		return -EINVAL;
 
 	ev = (struct wmi_pstream_timeout_event *) datap;
+	if (ev->traffic_class >= WMM_NUM_AC) {
+		ath6kl_err("invalid traffic class: %d\n", ev->traffic_class);
+		return -EINVAL;
+	}
 
 	/*
 	 * When the pstream (fat pipe == AC) timesout, it means there were
@@ -1519,6 +1523,10 @@ static int ath6kl_wmi_cac_event_rx(struct wmi *wmi, u8 *datap, int len,
 		return -EINVAL;
 
 	reply = (struct wmi_cac_event *) datap;
+	if (reply->ac >= WMM_NUM_AC) {
+		ath6kl_err("invalid AC: %d\n", reply->ac);
+		return -EINVAL;
+	}
 
 	if ((reply->cac_indication == CAC_INDICATION_ADMISSION_RESP) &&
 	    (reply->status_code != IEEE80211_TSPEC_STATUS_ADMISS_ACCEPTED)) {
@@ -2631,7 +2639,7 @@ int ath6kl_wmi_delete_pstream_cmd(struct wmi *wmi, u8 if_idx, u8 traffic_class,
 	u16 active_tsids = 0;
 	int ret;
 
-	if (traffic_class > 3) {
+	if (traffic_class >= WMM_NUM_AC) {
 		ath6kl_err("invalid traffic class: %d\n", traffic_class);
 		return -EINVAL;
 	}
Signature · 1 line
2.20.1
author maintainer
#3 lore raw

PATCH 4/53 ath: DFS JP domain W56 fixed pulse type 3 RADAR detection

In reply to Sasha Levin

From: Anilkumar Kolli <[email protected]>

[ Upstream commit d8792393a783158cbb2c39939cb897dc5e5299b6 ]

Increase pulse width range from 1-2usec to 0-4usec.
During data traffic HW occasionally fails detecting radar pulses, so that SW cannot get enough radar reports to achieve the success rate.

Tested ath10k hw and fw:
* QCA9888(10.4-3.5.1-00052)
* QCA4019(10.4-3.2.1.1-00017)
* QCA9984(10.4-3.6-00104)
* QCA988X(10.2.4-1.0-00041)

Tested ath9k hw: AR9300

---
 drivers/net/wireless/ath/dfs_pattern_detector.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/wireless/ath/dfs_pattern_detector.c +1 -1
index 2303ef96299d..0835828ffed7 100644
@@ -111,7 +111,7 @@ static const struct radar_detector_specs jp_radar_ref_types[] = {
 	JP_PATTERN(0, 0, 1, 1428, 1428, 1, 18, 29, false),
 	JP_PATTERN(1, 2, 3, 3846, 3846, 1, 18, 29, false),
 	JP_PATTERN(2, 0, 1, 1388, 1388, 1, 18, 50, false),
-	JP_PATTERN(3, 1, 2, 4000, 4000, 1, 18, 50, false),
+	JP_PATTERN(3, 0, 4, 4000, 4000, 1, 18, 50, false),
 	JP_PATTERN(4, 0, 5, 150, 230, 1, 23, 50, false),
 	JP_PATTERN(5, 6, 10, 200, 500, 1, 16, 50, false),
 	JP_PATTERN(6, 11, 20, 200, 500, 1, 12, 50, false),
Signature · 1 line
2.20.1
author maintainer
#4 lore raw

PATCH 5/53 batman-adv: fix for leaked TVLV handler.

In reply to Sasha Levin

From: Jeremy Sowden <[email protected]>

[ Upstream commit 17f78dd1bd624a4dd78ed5db3284a63ee807fcc3 ]

A handler for BATADV_TVLV_ROAM was being registered when the translation-table was initialized, but not unregistered when the translation-table was freed. Unregister it.

Fixes 122edaa05940 ("batman-adv: tvlv - convert roaming adv packet to use tvlv unicast packets")
Reported-by [email protected]
---
 net/batman-adv/translation-table.c | 2 ++
 1 file changed, 2 insertions(+)
net/batman-adv/translation-table.c +2 -0
index f2079acb555d..ffd49b40e76a 100644
@@ -3158,6 +3158,8 @@ static void batadv_tt_purge(struct work_struct *work)
 
 void batadv_tt_free(struct batadv_priv *bat_priv)
 {
+	batadv_tvlv_handler_unregister(bat_priv, BATADV_TVLV_ROAM, 1);
+
 	batadv_tvlv_container_unregister(bat_priv, BATADV_TVLV_TT, 1);
 	batadv_tvlv_handler_unregister(bat_priv, BATADV_TVLV_TT, 1);
 
Signature · 1 line
2.20.1
author maintainer
#5 lore raw

PATCH 6/53 media: dvb: usb: fix use after free in dvb_usb_device_exit

In reply to Sasha Levin

From: Oliver Neukum <[email protected]>

[ Upstream commit 6cf97230cd5f36b7665099083272595c55d72be7 ]

dvb_usb_device_exit() frees and uses the device name in that order. Fix by storing the name in a buffer before freeing it.

---
 drivers/media/usb/dvb-usb/dvb-usb-init.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/media/usb/dvb-usb/dvb-usb-init.c +5 -2
index 1adf325012f7..97a89ef7e4c1 100644
@@ -286,12 +286,15 @@ EXPORT_SYMBOL(dvb_usb_device_init);
 void dvb_usb_device_exit(struct usb_interface *intf)
 {
 	struct dvb_usb_device *d = usb_get_intfdata(intf);
-	const char *name = "generic DVB-USB module";
+	const char *default_name = "generic DVB-USB module";
+	char name[40];
 
 	usb_set_intfdata(intf, NULL);
 	if (d != NULL && d->desc != NULL) {
-		name = d->desc->name;
+		strscpy(name, d->desc->name, sizeof(name));
 		dvb_usb_exit(d);
+	} else {
+		strscpy(name, default_name, sizeof(name));
 	}
 	info("%s successfully deinitialized and disconnected.", name);
 
Signature · 1 line
2.20.1
author maintainer
#6 lore raw

PATCH 7/53 crypto: talitos - fix skcipher failure due to wrong output IV

In reply to Sasha Levin

From: Christophe Leroy <[email protected]>

[ Upstream commit 3e03e792865ae48b8cfc69a0b4d65f02f467389f ]

Selftests report the following:

[    2.984845] alg: skcipher: cbc-aes-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[    2.995377] 00000000: 3d af ba 42 9d 9e b4 30 b4 22 da 80 2c 9f ac 41
[    3.032673] alg: skcipher: cbc-des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[    3.043185] 00000000: fe dc ba 98 76 54 32 10
[    3.063238] alg: skcipher: cbc-3des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[    3.073818] 00000000: 7d 33 88 93 0f 93 b2 42

This above dumps show that the actual output IV is indeed the input IV. This is due to the IV not being copied back into the request.

This patch fixes that.

---
 drivers/crypto/talitos.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/crypto/talitos.c +4 -0
index 62ce93568e11..a000c2667392 100644
@@ -1446,11 +1446,15 @@ static void ablkcipher_done(struct device *dev,
 			    int err)
 {
 	struct ablkcipher_request *areq = context;
+	struct crypto_ablkcipher *cipher = crypto_ablkcipher_reqtfm(areq);
+	struct talitos_ctx *ctx = crypto_ablkcipher_ctx(cipher);
+	unsigned int ivsize = crypto_ablkcipher_ivsize(cipher);
 	struct talitos_edesc *edesc;
 
 	edesc = container_of(desc, struct talitos_edesc, desc);
 
 	common_nonsnoop_unmap(dev, edesc, areq);
+	memcpy(areq->info, ctx->iv, ivsize);
 
 	kfree(edesc);
 
Signature · 1 line
2.20.1
author maintainer
#7 lore raw

PATCH 8/53 media: marvell-ccic: fix DMA s/g desc number calculation

In reply to Sasha Levin

From: Lubomir Rintel <[email protected]>

[ Upstream commit 0c7aa32966dab0b8a7424e1b34c7f206817953ec ]

The commit d790b7eda953 ("[media] vb2-dma-sg: move dma_(un)map_sg here") left dma_desc_nent unset. It previously contained the number of DMA descriptors as returned from dma_map_sg().

We can now (since the commit referred to above) obtain the same value from the sg_table and drop dma_desc_nent altogether.

Tested on OLPC XO-1.75 machine. Doesn't affect the OLPC XO-1's Cafe driver, since that one doesn't do DMA.

[[email protected]: fix a checkpatch warning]

Fixes d790b7eda953 ("[media] vb2-dma-sg: move dma_(un)map_sg here")
---
 drivers/media/platform/marvell-ccic/mcam-core.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/media/platform/marvell-ccic/mcam-core.c +3 -2
index aa2b44041d3f..22fe771d4dd2 100644
@@ -209,7 +209,6 @@ struct mcam_vb_buffer {
 	struct list_head queue;
 	struct mcam_dma_desc *dma_desc;	/* Descriptor virtual address */
 	dma_addr_t dma_desc_pa;		/* Descriptor physical address */
-	int dma_desc_nent;		/* Number of mapped descriptors */
 };
 
 static inline struct mcam_vb_buffer *vb_to_mvb(struct vb2_v4l2_buffer *vb)
@@ -616,9 +615,11 @@ static void mcam_dma_contig_done(struct mcam_camera *cam, int frame)
 static void mcam_sg_next_buffer(struct mcam_camera *cam)
 {
 	struct mcam_vb_buffer *buf;
+	struct sg_table *sg_table;
 
 	buf = list_first_entry(&cam->buffers, struct mcam_vb_buffer, queue);
 	list_del_init(&buf->queue);
+	sg_table = vb2_dma_sg_plane_desc(&buf->vb_buf.vb2_buf, 0);
 	/*
 	 * Very Bad Not Good Things happen if you don't clear
 	 * C1_DESC_ENA before making any descriptor changes.
@@ -626,7 +627,7 @@ static void mcam_sg_next_buffer(struct mcam_camera *cam)
 	mcam_reg_clear_bit(cam, REG_CTRL1, C1_DESC_ENA);
 	mcam_reg_write(cam, REG_DMA_DESC_Y, buf->dma_desc_pa);
 	mcam_reg_write(cam, REG_DESC_LEN_Y,
-			buf->dma_desc_nent*sizeof(struct mcam_dma_desc));
+			sg_table->nents * sizeof(struct mcam_dma_desc));
 	mcam_reg_write(cam, REG_DESC_LEN_U, 0);
 	mcam_reg_write(cam, REG_DESC_LEN_V, 0);
 	mcam_reg_set_bit(cam, REG_CTRL1, C1_DESC_ENA);
Signature · 1 line
2.20.1
author maintainer
#8 lore raw

PATCH 9/53 media: vpss: fix a potential NULL pointer dereference

In reply to Sasha Levin

From: Kangjie Lu <[email protected]>

[ Upstream commit e08f0761234def47961d3252eac09ccedfe4c6a0 ]

In case ioremap fails, the fix returns -ENOMEM to avoid NULL pointer dereference.

---
 drivers/media/platform/davinci/vpss.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/media/platform/davinci/vpss.c +5 -0
index fce86f17dffc..c2c68988e38a 100644
@@ -523,6 +523,11 @@ static int __init vpss_init(void)
 		return -EBUSY;
 
 	oper_cfg.vpss_regs_base2 = ioremap(VPSS_CLK_CTRL, 4);
+	if (unlikely(!oper_cfg.vpss_regs_base2)) {
+		release_mem_region(VPSS_CLK_CTRL, 4);
+		return -ENOMEM;
+	}
+
 	writel(VPSS_CLK_CTRL_VENCCLKEN |
 		     VPSS_CLK_CTRL_DACCLKEN, oper_cfg.vpss_regs_base2);
 
Signature · 1 line
2.20.1
author maintainer
#9 lore raw

PATCH 10/53 net: stmmac: dwmac1000: Clear unused address entries

In reply to Sasha Levin

From: Jose Abreu <[email protected]>

[ Upstream commit 9463c445590091202659cdfdd44b236acadfbd84 ]

In case we don't use a given address entry we need to clear it because it could contain previous values that are no longer valid.

Found out while running stmmac selftests.

Cc Joao Pinto <[email protected]>
Cc David S. Miller <[email protected]>
Cc Giuseppe Cavallaro <[email protected]>
Cc Alexandre Torgue <[email protected]>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c | 6 ++++++
 1 file changed, 6 insertions(+)
drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c +6 -0
index 371a669d69fd..1df84c8de9d7 100644
@@ -187,6 +187,12 @@ static void dwmac1000_set_filter(struct mac_device_info *hw,
 					    GMAC_ADDR_LOW(reg));
 			reg++;
 		}
+
+		while (reg <= perfect_addr_number) {
+			writel(0, ioaddr + GMAC_ADDR_HIGH(reg));
+			writel(0, ioaddr + GMAC_ADDR_LOW(reg));
+			reg++;
+		}
 	}
 
 #ifdef FRAME_FILTER_DEBUG
Signature · 1 line
2.20.1
author maintainer
#10 lore raw

PATCH 11/53 signal/pid_namespace: Fix reboot_pid_ns to use send_sig not force_sig

In reply to Sasha Levin

From: "Eric W. Biederman" <[email protected]>

[ Upstream commit f9070dc94542093fd516ae4ccea17ef46a4362c5 ]

The locking in force_sig_info is not prepared to deal with a task that exits or execs (as sighand may change). The is not a locking problem in force_sig as force_sig is only built to handle synchronous exceptions.

Further the function force_sig_info changes the signal state if the signal is ignored, or blocked or if SIGNAL_UNKILLABLE will prevent the delivery of the signal. The signal SIGKILL can not be ignored and can not be blocked and SIGNAL_UNKILLABLE won't prevent it from being delivered.

So using force_sig rather than send_sig for SIGKILL is confusing and pointless.

Because it won't impact the sending of the signal and and because using force_sig is wrong, replace force_sig with send_sig.

Cc Daniel Lezcano <[email protected]>
Cc Serge Hallyn <[email protected]>
Cc Oleg Nesterov <[email protected]>
Fixes cf3f89214ef6 ("pidns: add reboot_pid_ns() to handle the reboot syscall")
---
 kernel/pid_namespace.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
kernel/pid_namespace.c +1 -1
index 567ecc826bc8..6353372801f2 100644
@@ -325,7 +325,7 @@ int reboot_pid_ns(struct pid_namespace *pid_ns, int cmd)
 	}
 
 	read_lock(&tasklist_lock);
-	force_sig(SIGKILL, pid_ns->child_reaper);
+	send_sig(SIGKILL, pid_ns->child_reaper, 1);
 	read_unlock(&tasklist_lock);
 
 	do_exit(0);
Signature · 1 line
2.20.1
author maintainer
#11 lore raw

PATCH 12/53 signal/cifs: Fix cifs_put_tcp_session to call send_sig instead of force_sig

In reply to Sasha Levin

From: "Eric W. Biederman" <[email protected]>

[ Upstream commit 72abe3bcf0911d69b46c1e8bdb5612675e0ac42c ]

The locking in force_sig_info is not prepared to deal with a task that exits or execs (as sighand may change). The is not a locking problem in force_sig as force_sig is only built to handle synchronous exceptions.

Further the function force_sig_info changes the signal state if the signal is ignored, or blocked or if SIGNAL_UNKILLABLE will prevent the delivery of the signal. The signal SIGKILL can not be ignored and can not be blocked and SIGNAL_UNKILLABLE won't prevent it from being delivered.

So using force_sig rather than send_sig for SIGKILL is confusing and pointless.

Because it won't impact the sending of the signal and and because using force_sig is wrong, replace force_sig with send_sig.

Cc Namjae Jeon <[email protected]>
Cc Jeff Layton <[email protected]>
Cc Steve French <[email protected]>
Fixes a5c3e1c725af ("Revert "cifs: No need to send SIGKILL to demux_thread during umount"")
Fixes e7ddee9037e7 ("cifs: disable sharing session and tcon and add new TCP sharing code")
---
 fs/cifs/connect.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
fs/cifs/connect.c +1 -1
index 9cb72fd40eff..bc7c287a2e17 100644
@@ -2246,7 +2246,7 @@ cifs_put_tcp_session(struct TCP_Server_Info *server, int from_reconnect)
 
 	task = xchg(&server->tsk, NULL);
 	if (task)
-		force_sig(SIGKILL, task);
+		send_sig(SIGKILL, task, 1);
 }
 
 static struct TCP_Server_Info *
Signature · 1 line
2.20.1
author maintainer
#12 lore raw

PATCH 13/53 af_key: fix leaks in key_pol_get_resp and dump_sp.

In reply to Sasha Levin

From: Jeremy Sowden <[email protected]>

[ Upstream commit 7c80eb1c7e2b8420477fbc998971d62a648035d9 ]

In both functions, if pfkey_xfrm_policy2msg failed we leaked the newly allocated sk_buff. Free it on error.

Fixes 55569ce256ce ("Fix conversion between IPSEC_MODE_xxx and XFRM_MODE_xxx.")
Reported-by [email protected]
---
 net/key/af_key.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)
net/key/af_key.c +6 -2
index 3ba903ff2bb0..36db179d848e 100644
@@ -2463,8 +2463,10 @@ static int key_pol_get_resp(struct sock *sk, struct xfrm_policy *xp, const struc
 		goto out;
 	}
 	err = pfkey_xfrm_policy2msg(out_skb, xp, dir);
-	if (err < 0)
+	if (err < 0) {
+		kfree_skb(out_skb);
 		goto out;
+	}
 
 	out_hdr = (struct sadb_msg *) out_skb->data;
 	out_hdr->sadb_msg_version = hdr->sadb_msg_version;
@@ -2717,8 +2719,10 @@ static int dump_sp(struct xfrm_policy *xp, int dir, int count, void *ptr)
 		return PTR_ERR(out_skb);
 
 	err = pfkey_xfrm_policy2msg(out_skb, xp, dir);
-	if (err < 0)
+	if (err < 0) {
+		kfree_skb(out_skb);
 		return err;
+	}
 
 	out_hdr = (struct sadb_msg *) out_skb->data;
 	out_hdr->sadb_msg_version = pfk->dump.msg_version;
Signature · 1 line
2.20.1
author maintainer
#13 lore raw

PATCH 14/53 xfrm: Fix xfrm sel prefix length validation

In reply to Sasha Levin

From: Anirudh Gupta <[email protected]>

[ Upstream commit b38ff4075a80b4da5cb2202d7965332ca0efb213 ]

Family of src/dst can be different from family of selector src/dst. Use xfrm selector family to validate address prefix length, while verifying new sa from userspace.

Validated patch with this command:
ip xfrm state add src 1.1.6.1 dst 1.1.6.2 proto esp spi 4260196 \
reqid 20004 mode tunnel aead "rfc4106(gcm(aes))" \
0x1111016400000000000000000000000044440001 128 \
sel src 1011:1:4::2/128 sel dst 1021:1:4::2/128 dev Port5

Fixes 07bf7908950a ("xfrm: Validate address prefix lengths in the xfrm selector.")
---
 net/xfrm/xfrm_user.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)
net/xfrm/xfrm_user.c +16 -0
index b04c03043976..10fda9a39cc2 100644
@@ -150,6 +150,22 @@ static int verify_newsa_info(struct xfrm_usersa_info *p,
 
 	err = -EINVAL;
 	switch (p->family) {
+	case AF_INET:
+		break;
+
+	case AF_INET6:
+#if IS_ENABLED(CONFIG_IPV6)
+		break;
+#else
+		err = -EAFNOSUPPORT;
+		goto out;
+#endif
+
+	default:
+		goto out;
+	}
+
+	switch (p->sel.family) {
 	case AF_INET:
 		if (p->sel.prefixlen_d > 32 || p->sel.prefixlen_s > 32)
 			goto out;
Signature · 1 line
2.20.1
author maintainer
#14 lore raw

PATCH 15/53 e1000e: start network tx queue only when link is up

In reply to Sasha Levin

From: Konstantin Khlebnikov <[email protected]>

[ Upstream commit d17ba0f616a08f597d9348c372d89b8c0405ccf3 ]

Driver does not want to keep packets in Tx queue when link is lost. But present code only reset NIC to flush them, but does not prevent queuing new packets. Moreover reset sequence itself could generate new packets via netconsole and NIC falls into endless reset loop.

This patch wakes Tx queue only when NIC is ready to send packets.

This is proper fix for problem addressed by commit 0f9e980bf5ee ("e1000e: fix cyclic resets at link up with active tx").

---
 drivers/net/ethernet/intel/e1000e/netdev.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/net/ethernet/intel/e1000e/netdev.c +4 -2
index 6b1cacd86c6e..7d64edeb1830 100644
@@ -4171,7 +4171,7 @@ int e1000e_up(struct e1000_adapter *adapter)
 		e1000_configure_msix(adapter);
 	e1000_irq_enable(adapter);
 
-	netif_start_queue(adapter->netdev);
+	/* Tx queue started by watchdog timer when link is up */
 
 	/* fire a link change interrupt to start the watchdog */
 	if (adapter->msix_entries)
@@ -4539,6 +4539,7 @@ static int e1000_open(struct net_device *netdev)
 	pm_runtime_get_sync(&pdev->dev);
 
 	netif_carrier_off(netdev);
+	netif_stop_queue(netdev);
 
 	/* allocate transmit descriptors */
 	err = e1000e_setup_tx_resources(adapter->tx_ring);
@@ -4599,7 +4600,6 @@ static int e1000_open(struct net_device *netdev)
 	e1000_irq_enable(adapter);
 
 	adapter->tx_hang_recheck = false;
-	netif_start_queue(netdev);
 
 	hw->mac.get_link_status = true;
 	pm_runtime_put(&pdev->dev);
@@ -5226,6 +5226,7 @@ static void e1000_watchdog_task(struct work_struct *work)
 			if (phy->ops.cfg_on_link_up)
 				phy->ops.cfg_on_link_up(hw);
 
+			netif_wake_queue(netdev);
 			netif_carrier_on(netdev);
 
 			if (!test_bit(__E1000_DOWN, &adapter->state))
@@ -5239,6 +5240,7 @@ static void e1000_watchdog_task(struct work_struct *work)
 			/* Link status message must follow this format */
 			pr_info("%s NIC Link is Down\n", adapter->netdev->name);
 			netif_carrier_off(netdev);
+			netif_stop_queue(netdev);
 			if (!test_bit(__E1000_DOWN, &adapter->state))
 				mod_timer(&adapter->phy_info_timer,
 					  round_jiffies(jiffies + 2 * HZ));
Signature · 1 line
2.20.1
author maintainer
#15 lore raw

PATCH 16/53 media: staging: media: davinci_vpfe: - Fix for memory leak if decoder initialization fails.

In reply to Sasha Levin

From: Shailendra Verma <[email protected]>

[ Upstream commit 6995a659101bd4effa41cebb067f9dc18d77520d ]

Fix to avoid possible memory leak if the decoder initialization got failed.Free the allocated memory for file handle object before return in case decoder initialization fails.

---
 drivers/staging/media/davinci_vpfe/vpfe_video.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/staging/media/davinci_vpfe/vpfe_video.c +3 -0
index 0fdff91624fd..43474f562b43 100644
@@ -406,6 +406,9 @@ static int vpfe_open(struct file *file)
 	/* If decoder is not initialized. initialize it */
 	if (!video->initialized && vpfe_update_pipe_state(video)) {
 		mutex_unlock(&video->lock);
+		v4l2_fh_del(&handle->vfh);
+		v4l2_fh_exit(&handle->vfh);
+		kfree(handle);
 		return -ENODEV;
 	}
 	/* Increment device users counter */
Signature · 1 line
2.20.1
author maintainer
#16 lore raw

PATCH 17/53 net: phy: Check against net_device being NULL

In reply to Sasha Levin

From: Ioana Ciornei <[email protected]>

[ Upstream commit 82c76aca81187b3d28a6fb3062f6916450ce955e ]

In general, we don't want MAC drivers calling phy_attach_direct with the net_device being NULL. Add checks against this in all the functions calling it: phy_attach() and phy_connect_direct().

---
 drivers/net/phy/phy_device.c | 6 ++++++
 1 file changed, 6 insertions(+)
drivers/net/phy/phy_device.c +6 -0
index 70f26b30729c..c6a87834723d 100644
@@ -472,6 +472,9 @@ int phy_connect_direct(struct net_device *dev, struct phy_device *phydev,
 {
 	int rc;
 
+	if (!dev)
+		return -EINVAL;
+
 	rc = phy_attach_direct(dev, phydev, phydev->dev_flags, interface);
 	if (rc)
 		return rc;
@@ -704,6 +707,9 @@ struct phy_device *phy_attach(struct net_device *dev, const char *bus_id,
 	struct device *d;
 	int rc;
 
+	if (!dev)
+		return ERR_PTR(-EINVAL);
+
 	/* Search the list of PHY devices on the mdio bus for the
 	 * PHY with the requested name
 	 */
Signature · 1 line
2.20.1
author maintainer
#17 lore raw

PATCH 18/53 tua6100: Avoid build warnings.

In reply to Sasha Levin

From: "David S. Miller" <[email protected]>

[ Upstream commit 621ccc6cc5f8d6730b740d31d4818227866c93c9 ]

Rename _P to _P_VAL and _R to _R_VAL to avoid global namespace conflicts:

drivers/media/dvb-frontends/tua6100.c: In function ‘tua6100_set_params’:
drivers/media/dvb-frontends/tua6100.c:79: warning: "_P" redefined
#define _P 32

In file included from ./include/acpi/platform/aclinux.h:54,

                 from ./include/acpi/platform/acenv.h:152,
                 from ./include/acpi/acpi.h:22,
                 from ./include/linux/acpi.h:34,
                 from ./include/linux/i2c.h:17,
                 from drivers/media/dvb-frontends/tua6100.h:30,
                 from drivers/media/dvb-frontends/tua6100.c:32:

./include/linux/ctype.h:14: note: this is the location of the previous definition
#define _P 0x10 /* punct */

---
 drivers/media/dvb-frontends/tua6100.c | 22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)
drivers/media/dvb-frontends/tua6100.c +11 -11
index 029384d1fddd..7a3e91cda5df 100644
@@ -80,8 +80,8 @@ static int tua6100_set_params(struct dvb_frontend *fe)
 	struct i2c_msg msg1 = { .addr = priv->i2c_address, .flags = 0, .buf = reg1, .len = 4 };
 	struct i2c_msg msg2 = { .addr = priv->i2c_address, .flags = 0, .buf = reg2, .len = 3 };
 
-#define _R 4
-#define _P 32
+#define _R_VAL 4
+#define _P_VAL 32
 #define _ri 4000000
 
 	// setup register 0
@@ -96,14 +96,14 @@ static int tua6100_set_params(struct dvb_frontend *fe)
 	else
 		reg1[1] = 0x0c;
 
-	if (_P == 64)
+	if (_P_VAL == 64)
 		reg1[1] |= 0x40;
 	if (c->frequency >= 1525000)
 		reg1[1] |= 0x80;
 
 	// register 2
-	reg2[1] = (_R >> 8) & 0x03;
-	reg2[2] = _R;
+	reg2[1] = (_R_VAL >> 8) & 0x03;
+	reg2[2] = _R_VAL;
 	if (c->frequency < 1455000)
 		reg2[1] |= 0x1c;
 	else if (c->frequency < 1630000)
@@ -115,18 +115,18 @@ static int tua6100_set_params(struct dvb_frontend *fe)
 	 * The N divisor ratio (note: c->frequency is in kHz, but we
 	 * need it in Hz)
 	 */
-	prediv = (c->frequency * _R) / (_ri / 1000);
-	div = prediv / _P;
+	prediv = (c->frequency * _R_VAL) / (_ri / 1000);
+	div = prediv / _P_VAL;
 	reg1[1] |= (div >> 9) & 0x03;
 	reg1[2] = div >> 1;
 	reg1[3] = (div << 7);
-	priv->frequency = ((div * _P) * (_ri / 1000)) / _R;
+	priv->frequency = ((div * _P_VAL) * (_ri / 1000)) / _R_VAL;
 
 	// Finally, calculate and store the value for A
-	reg1[3] |= (prediv - (div*_P)) & 0x7f;
+	reg1[3] |= (prediv - (div*_P_VAL)) & 0x7f;
 
-#undef _R
-#undef _P
+#undef _R_VAL
+#undef _P_VAL
 #undef _ri
 
 	if (fe->ops.i2c_gate_ctrl)
Signature · 1 line
2.20.1
author maintainer
#18 lore raw

PATCH 19/53 locking/lockdep: Fix merging of hlocks with non-zero references

In reply to Sasha Levin

From: Imre Deak <[email protected]>

[ Upstream commit d9349850e188b8b59e5322fda17ff389a1c0cd7d ]

The sequence

	static DEFINE_WW_CLASS(test_ww_class);

	struct ww_acquire_ctx ww_ctx;
	struct ww_mutex ww_lock_a;
	struct ww_mutex ww_lock_b;
	struct ww_mutex ww_lock_c;
	struct mutex lock_c;

	ww_acquire_init(&ww_ctx, &test_ww_class);

	ww_mutex_init(&ww_lock_a, &test_ww_class);
	ww_mutex_init(&ww_lock_b, &test_ww_class);
	ww_mutex_init(&ww_lock_c, &test_ww_class);

	mutex_init(&lock_c);

	ww_mutex_lock(&ww_lock_a, &ww_ctx);

	mutex_lock(&lock_c);

	ww_mutex_lock(&ww_lock_b, &ww_ctx);
	ww_mutex_lock(&ww_lock_c, &ww_ctx);

	mutex_unlock(&lock_c);	(*)

	ww_mutex_unlock(&ww_lock_c);
	ww_mutex_unlock(&ww_lock_b);
	ww_mutex_unlock(&ww_lock_a);

	ww_acquire_fini(&ww_ctx); (**)

will trigger the following error in __lock_release() when calling mutex_release() at **:

	DEBUG_LOCKS_WARN_ON(depth <= 0)

The problem is that the hlock merging happening at * updates the references for test_ww_class incorrectly to 3 whereas it should've updated it to 4 (representing all the instances for ww_ctx and ww_lock_[abc]).

Fix this by updating the references during merging correctly taking into account that we can have non-zero references (both for the hlock that we merge into another hlock or for the hlock we are merging into).

---
 kernel/locking/lockdep.c | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)
kernel/locking/lockdep.c +9 -9
index 774ab79d3ec7..f2df5f86af28 100644
@@ -3128,17 +3128,17 @@ static int __lock_acquire(struct lockdep_map *lock, unsigned int subclass,
 	if (depth) {
 		hlock = curr->held_locks + depth - 1;
 		if (hlock->class_idx == class_idx && nest_lock) {
-			if (hlock->references) {
-				/*
-				 * Check: unsigned int references:12, overflow.
-				 */
-				if (DEBUG_LOCKS_WARN_ON(hlock->references == (1 << 12)-1))
-					return 0;
+			if (!references)
+				references++;
 
+			if (!hlock->references)
 				hlock->references++;
-			} else {
-				hlock->references = 2;
-			}
+
+			hlock->references += references;
+
+			/* Overflow */
+			if (DEBUG_LOCKS_WARN_ON(hlock->references < references))
+				return 0;
 
 			return 1;
 		}
Signature · 1 line
2.20.1
author maintainer
#19 lore raw

PATCH 20/53 media: wl128x: Fix some error handling in fm_v4l2_init_video_device()

In reply to Sasha Levin

From: Kefeng Wang <[email protected]>

[ Upstream commit 69fbb3f47327d959830c94bf31893972b8c8f700 ]

X-Originating-IP: [10.175.113.25]
X-CFilter-Loop: Reflected
The fm_v4l2_init_video_device() forget to unregister v4l2/video device in the error path, it could lead to UAF issue, eg,

  BUG: KASAN: use-after-free in atomic64_read include/asm-generic/atomic-instrumented.h:836 [inline]
  BUG: KASAN: use-after-free in atomic_long_read include/asm-generic/atomic-long.h:28 [inline]
  BUG: KASAN: use-after-free in __mutex_unlock_slowpath+0x92/0x690 kernel/locking/mutex.c:1206
  Read of size 8 at addr ffff8881e84a7c70 by task v4l_id/3659

  CPU: 1 PID: 3659 Comm: v4l_id Not tainted 5.1.0 #8
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
  Call Trace:
   __dump_stack lib/dump_stack.c:77 [inline]
   dump_stack+0xa9/0x10e lib/dump_stack.c:113
   print_address_description+0x65/0x270 mm/kasan/report.c:187
   kasan_report+0x149/0x18d mm/kasan/report.c:317
   atomic64_read include/asm-generic/atomic-instrumented.h:836 [inline]
   atomic_long_read include/asm-generic/atomic-long.h:28 [inline]
   __mutex_unlock_slowpath+0x92/0x690 kernel/locking/mutex.c:1206
   fm_v4l2_fops_open+0xac/0x120 [fm_drv]
   v4l2_open+0x191/0x390 [videodev]
   chrdev_open+0x20d/0x570 fs/char_dev.c:417
   do_dentry_open+0x700/0xf30 fs/open.c:777
   do_last fs/namei.c:3416 [inline]
   path_openat+0x7c4/0x2a90 fs/namei.c:3532
   do_filp_open+0x1a5/0x2b0 fs/namei.c:3563
   do_sys_open+0x302/0x490 fs/open.c:1069
   do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290
   entry_SYSCALL_64_after_hwframe+0x49/0xbe
  RIP: 0033:0x7f8180c17c8e
  ...
  Allocated by task 3642:
   set_track mm/kasan/common.c:87 [inline]
   __kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:497
   fm_drv_init+0x13/0x1000 [fm_drv]
   do_one_initcall+0xbc/0x47d init/main.c:901
   do_init_module+0x1b5/0x547 kernel/module.c:3456
   load_module+0x6405/0x8c10 kernel/module.c:3804
   __do_sys_finit_module+0x162/0x190 kernel/module.c:3898
   do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290
   entry_SYSCALL_64_after_hwframe+0x49/0xbe

  Freed by task 3642:
   set_track mm/kasan/common.c:87 [inline]
   __kasan_slab_free+0x130/0x180 mm/kasan/common.c:459
   slab_free_hook mm/slub.c:1429 [inline]
   slab_free_freelist_hook mm/slub.c:1456 [inline]
   slab_free mm/slub.c:3003 [inline]
   kfree+0xe1/0x270 mm/slub.c:3958
   fm_drv_init+0x1e6/0x1000 [fm_drv]
   do_one_initcall+0xbc/0x47d init/main.c:901
   do_init_module+0x1b5/0x547 kernel/module.c:3456
   load_module+0x6405/0x8c10 kernel/module.c:3804
   __do_sys_finit_module+0x162/0x190 kernel/module.c:3898
   do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290
   entry_SYSCALL_64_after_hwframe+0x49/0xbe

Add relevant unregister functions to fix it.

---
 drivers/media/radio/wl128x/fmdrv_v4l2.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/media/radio/wl128x/fmdrv_v4l2.c +3 -0
index fb42f0fd0c1f..add26eac1677 100644
@@ -553,6 +553,7 @@ int fm_v4l2_init_video_device(struct fmdev *fmdev, int radio_nr)
 
 	/* Register with V4L2 subsystem as RADIO device */
 	if (video_register_device(&gradio_dev, VFL_TYPE_RADIO, radio_nr)) {
+		v4l2_device_unregister(&fmdev->v4l2_dev);
 		fmerr("Could not register video device\n");
 		return -ENOMEM;
 	}
@@ -566,6 +567,8 @@ int fm_v4l2_init_video_device(struct fmdev *fmdev, int radio_nr)
 	if (ret < 0) {
 		fmerr("(fmdev): Can't init ctrl handler\n");
 		v4l2_ctrl_handler_free(&fmdev->ctrl_handler);
+		video_unregister_device(fmdev->radio_dev);
+		v4l2_device_unregister(&fmdev->v4l2_dev);
 		return -EBUSY;
 	}
 
Signature · 1 line
2.20.1
author maintainer
#20 lore raw

PATCH 21/53 cpupower : frequency-set -r option misses the last cpu in related cpu list

In reply to Sasha Levin

From: Abhishek Goel <[email protected]>

[ Upstream commit 04507c0a9385cc8280f794a36bfff567c8cc1042 ]

To set frequency on specific cpus using cpupower, following syntax can be used :
cpupower -c #i frequency-set -f #f -r

While setting frequency using cpupower frequency-set command, if we use '-r' option, it is expected to set frequency for all cpus related to cpu #i. But it is observed to be missing the last cpu in related cpu list. This patch fixes the problem.

---
 tools/power/cpupower/utils/cpufreq-set.c | 2 ++
 1 file changed, 2 insertions(+)
tools/power/cpupower/utils/cpufreq-set.c +2 -0
index 0fbd1a22c0a9..2f86935094ca 100644
@@ -306,6 +306,8 @@ int cmd_freq_set(int argc, char **argv)
 				bitmask_setbit(cpus_chosen, cpus->cpu);
 				cpus = cpus->next;
 			}
+			/* Set the last cpu in related cpus list */
+			bitmask_setbit(cpus_chosen, cpus->cpu);
 			cpufreq_put_related_cpus(cpus);
 		}
 	}
Signature · 1 line
2.20.1
author maintainer
#21 lore raw

PATCH 22/53 net: fec: Do not use netdev messages too early

In reply to Sasha Levin

From: Fabio Estevam <[email protected]>

[ Upstream commit a19a0582363b9a5f8ba812f34f1b8df394898780 ]

When a valid MAC address is not found the current messages are shown:

fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00 fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: aa:9f:25:eb:7e:aa

Since the network device has not been registered at this point, it is better to use dev_err()/dev_info() instead, which will provide cleaner log messages like these:

fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00 fec 2188000.ethernet: Using random MAC address: aa:9f:25:eb:7e:aa

Tested on a imx6dl-pico-pi board.

---
 drivers/net/ethernet/freescale/fec_main.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/net/ethernet/freescale/fec_main.c +3 -3
index ae8e4fc22e7b..0ee164d09f39 100644
@@ -1699,10 +1699,10 @@ static void fec_get_mac(struct net_device *ndev)
 	 */
 	if (!is_valid_ether_addr(iap)) {
 		/* Report it and use a random ethernet address instead */
-		netdev_err(ndev, "Invalid MAC address: %pM\n", iap);
+		dev_err(&fep->pdev->dev, "Invalid MAC address: %pM\n", iap);
 		eth_hw_addr_random(ndev);
-		netdev_info(ndev, "Using random MAC address: %pM\n",
-			    ndev->dev_addr);
+		dev_info(&fep->pdev->dev, "Using random MAC address: %pM\n",
+			 ndev->dev_addr);
 		return;
 	}
 
Signature · 1 line
2.20.1
author maintainer
#22 lore raw

PATCH 23/53 net: axienet: Fix race condition causing TX hang

In reply to Sasha Levin

From: Robert Hancock <[email protected]>

[ Upstream commit 7de44285c1f69ccfbe8be1d6a16fcd956681fee6 ]

It is possible that the interrupt handler fires and frees up space in the TX ring in between checking for sufficient TX ring space and stopping the TX queue in axienet_start_xmit. If this happens, the queue wake from the interrupt handler will occur before the queue is stopped, causing a lost wakeup and the adapter's transmit hanging.

To avoid this, after stopping the queue, check again whether there is sufficient space in the TX ring. If so, wake up the queue again.

---
 .../net/ethernet/xilinx/xilinx_axienet_main.c | 20 ++++++++++++++++---
 1 file changed, 17 insertions(+), 3 deletions(-)
drivers/net/ethernet/xilinx/xilinx_axienet_main.c +17 -3
index 58ba579793f8..f1e969128a4e 100644
@@ -613,6 +613,10 @@ static void axienet_start_xmit_done(struct net_device *ndev)
 
 	ndev->stats.tx_packets += packets;
 	ndev->stats.tx_bytes += size;
+
+	/* Matches barrier in axienet_start_xmit */
+	smp_mb();
+
 	netif_wake_queue(ndev);
 }
 
@@ -667,9 +671,19 @@ static int axienet_start_xmit(struct sk_buff *skb, struct net_device *ndev)
 	cur_p = &lp->tx_bd_v[lp->tx_bd_tail];
 
 	if (axienet_check_tx_bd_space(lp, num_frag)) {
-		if (!netif_queue_stopped(ndev))
-			netif_stop_queue(ndev);
-		return NETDEV_TX_BUSY;
+		if (netif_queue_stopped(ndev))
+			return NETDEV_TX_BUSY;
+
+		netif_stop_queue(ndev);
+
+		/* Matches barrier in axienet_start_xmit_done */
+		smp_mb();
+
+		/* Space might have just been freed - check again */
+		if (axienet_check_tx_bd_space(lp, num_frag))
+			return NETDEV_TX_BUSY;
+
+		netif_wake_queue(ndev);
 	}
 
 	if (skb->ip_summed == CHECKSUM_PARTIAL) {
Signature · 1 line
2.20.1
author maintainer
#23 lore raw

PATCH 24/53 s390/qdio: handle PENDING state for QEBSM devices

In reply to Sasha Levin

From: Julian Wiedmann <[email protected]>

[ Upstream commit 04310324c6f482921c071444833e70fe861b73d9 ]

When a CQ-enabled device uses QEBSM for SBAL state inspection, get_buf_states() can return the PENDING state for an Output Queue. get_outbound_buffer_frontier() isn't prepared for this, and any PENDING buffer will permanently stall all further completion processing on this Queue.

This isn't a concern for non-QEBSM devices, as get_buf_states() for such devices will manually turn PENDING buffers into EMPTY ones.

Fixes 104ea556ee7f ("qdio: support asynchronous delivery of storage blocks")
---
 drivers/s390/cio/qdio_main.c | 1 +
 1 file changed, 1 insertion(+)
drivers/s390/cio/qdio_main.c +1 -0
index d64b401f3d05..8d7fc3b6ca63 100644
@@ -752,6 +752,7 @@ static int get_outbound_buffer_frontier(struct qdio_q *q)
 
 	switch (state) {
 	case SLSB_P_OUTPUT_EMPTY:
+	case SLSB_P_OUTPUT_PENDING:
 		/* the adapter got it */
 		DBF_DEV_EVENT(DBF_INFO, q->irq_ptr,
 			"out empty:%1d %02x", q->nr, count);
Signature · 1 line
2.20.1
author maintainer
#24 lore raw

PATCH 25/53 perf test 6: Fix missing kvm module load for s390

In reply to Sasha Levin

From: Thomas Richter <[email protected]>

[ Upstream commit 53fe307dfd309e425b171f6272d64296a54f4dff ]

Command

   # perf test -Fv 6

fails with error

running test 100 'kvm-s390:kvm_s390_create_vm' failed to parse

    event 'kvm-s390:kvm_s390_create_vm', err -1, str 'unknown tracepoint'
    event syntax error: 'kvm-s390:kvm_s390_create_vm'
                         \___ unknown tracepoint

when the kvm module is not loaded or not built in.

Fix this by adding a valid function which tests if the module is loaded. Loaded modules (or builtin KVM support) have a directory named
/sys/kernel/debug/tracing/events/kvm-s390
for this tracepoint.

Check for existence of this directory.

---
 tools/perf/tests/parse-events.c | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)
tools/perf/tests/parse-events.c +27 -0
index 54af2f2e2ee4..1a35ab044c11 100644
@@ -12,6 +12,32 @@
 #define PERF_TP_SAMPLE_TYPE (PERF_SAMPLE_RAW | PERF_SAMPLE_TIME | \
 			     PERF_SAMPLE_CPU | PERF_SAMPLE_PERIOD)
 
+#if defined(__s390x__)
+/* Return true if kvm module is available and loaded. Test this
+ * and retun success when trace point kvm_s390_create_vm
+ * exists. Otherwise this test always fails.
+ */
+static bool kvm_s390_create_vm_valid(void)
+{
+	char *eventfile;
+	bool rc = false;
+
+	eventfile = get_events_file("kvm-s390");
+
+	if (eventfile) {
+		DIR *mydir = opendir(eventfile);
+
+		if (mydir) {
+			rc = true;
+			closedir(mydir);
+		}
+		put_events_file(eventfile);
+	}
+
+	return rc;
+}
+#endif
+
 static int test__checkevent_tracepoint(struct perf_evlist *evlist)
 {
 	struct perf_evsel *evsel = perf_evlist__first(evlist);
@@ -1561,6 +1587,7 @@ static struct evlist_test test__events[] = {
 	{
 		.name  = "kvm-s390:kvm_s390_create_vm",
 		.check = test__checkevent_tracepoint,
+		.valid = kvm_s390_create_vm_valid,
 		.id    = 100,
 	},
 #endif
Signature · 1 line
2.20.1
author maintainer
#25 lore raw

PATCH 26/53 gpio: omap: fix lack of irqstatus_raw0 for OMAP4

In reply to Sasha Levin

From: Russell King <[email protected]>

[ Upstream commit 64ea3e9094a1f13b96c33244a3fb3a0f45690bd2 ]

Commit 384ebe1c2849 ("gpio/omap: Add DT support to GPIO driver") added the register definition tables to the gpio-omap driver. Subsequently to that commit, commit 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()") added definitions for irqstatus_raw* registers to the legacy OMAP4 definitions, but missed the DT definitions.

This causes an unintentional change of behaviour for the 1.101 errata workaround on OMAP4 platforms. Fix this oversight.

Fixes 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()")
---
 drivers/gpio/gpio-omap.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/gpio/gpio-omap.c +2 -0
index c8c49b1d5f9f..f23136825a6e 100644
@@ -1611,6 +1611,8 @@ static struct omap_gpio_reg_offs omap4_gpio_regs = {
 	.clr_dataout =		OMAP4_GPIO_CLEARDATAOUT,
 	.irqstatus =		OMAP4_GPIO_IRQSTATUS0,
 	.irqstatus2 =		OMAP4_GPIO_IRQSTATUS1,
+	.irqstatus_raw0 =	OMAP4_GPIO_IRQSTATUSRAW0,
+	.irqstatus_raw1 =	OMAP4_GPIO_IRQSTATUSRAW1,
 	.irqenable =		OMAP4_GPIO_IRQSTATUSSET0,
 	.irqenable2 =		OMAP4_GPIO_IRQSTATUSSET1,
 	.set_irqenable =	OMAP4_GPIO_IRQSTATUSSET0,
Signature · 1 line
2.20.1
author maintainer
#26 lore raw

PATCH 27/53 gpio: omap: ensure irq is enabled before wakeup

In reply to Sasha Levin

From: Russell King <[email protected]>

[ Upstream commit c859e0d479b3b4f6132fc12637c51e01492f31f6 ]

Documentation states:

NOTE: There must be a correlation between the wake-up enable and interrupt-enable registers. If a GPIO pin has a wake-up configured on it, it must also have the corresponding interrupt enabled (on one of the two interrupt lines).

Ensure that this condition is always satisfied by enabling the detection events after enabling the interrupt, and disabling the detection before disabling the interrupt. This ensures interrupt/wakeup events can not happen until both the wakeup and interrupt enables correlate.

If we do any clearing, clear between the interrupt enable/disable and trigger setting.

---
 drivers/gpio/gpio-omap.c | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)
drivers/gpio/gpio-omap.c +8 -7
index f23136825a6e..6e65c02baad1 100644
@@ -821,9 +821,9 @@ static void omap_gpio_irq_shutdown(struct irq_data *d)
 
 	raw_spin_lock_irqsave(&bank->lock, flags);
 	bank->irq_usage &= ~(BIT(offset));
-	omap_set_gpio_irqenable(bank, offset, 0);
-	omap_clear_gpio_irqstatus(bank, offset);
 	omap_set_gpio_triggering(bank, offset, IRQ_TYPE_NONE);
+	omap_clear_gpio_irqstatus(bank, offset);
+	omap_set_gpio_irqenable(bank, offset, 0);
 	if (!LINE_USED(bank->mod_usage, offset))
 		omap_clear_gpio_debounce(bank, offset);
 	omap_disable_gpio_module(bank, offset);
@@ -865,8 +865,8 @@ static void omap_gpio_mask_irq(struct irq_data *d)
 	unsigned long flags;
 
 	raw_spin_lock_irqsave(&bank->lock, flags);
-	omap_set_gpio_irqenable(bank, offset, 0);
 	omap_set_gpio_triggering(bank, offset, IRQ_TYPE_NONE);
+	omap_set_gpio_irqenable(bank, offset, 0);
 	raw_spin_unlock_irqrestore(&bank->lock, flags);
 }
 
@@ -878,9 +878,6 @@ static void omap_gpio_unmask_irq(struct irq_data *d)
 	unsigned long flags;
 
 	raw_spin_lock_irqsave(&bank->lock, flags);
-	if (trigger)
-		omap_set_gpio_triggering(bank, offset, trigger);
-
 	omap_set_gpio_irqenable(bank, offset, 1);
 
 	/*
@@ -888,9 +885,13 @@ static void omap_gpio_unmask_irq(struct irq_data *d)
 	 * is cleared, thus after the handler has run. OMAP4 needs this done
 	 * after enabing the interrupt to clear the wakeup status.
 	 */
-	if (bank->level_mask & BIT(offset))
+	if (bank->regs->leveldetect0 && bank->regs->wkup_en &&
+	    trigger & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW))
 		omap_clear_gpio_irqstatus(bank, offset);
 
+	if (trigger)
+		omap_set_gpio_triggering(bank, offset, trigger);
+
 	raw_spin_unlock_irqrestore(&bank->lock, flags);
 }
 
Signature · 1 line
2.20.1
author maintainer
#27 lore raw

PATCH 28/53 regmap: fix bulk writes on paged registers

In reply to Sasha Levin

From: Srinivas Kandagatla <[email protected]>

[ Upstream commit db057679de3e9e6a03c1bcd5aee09b0d25fd9f5b ]

On buses like SlimBus and SoundWire which does not support gather_writes yet in regmap, A bulk write on paged register would be silently ignored after programming page.
This is because local variable 'ret' value in regmap_raw_write_impl() gets reset to 0 once page register is written successfully and the code below checks for 'ret' value to be -ENOTSUPP before linearising the write buffer to send to bus->write().

Fix this by resetting the 'ret' value to -ENOTSUPP in cases where gather_writes() is not supported or single register write is not possible.

---
 drivers/base/regmap/regmap.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/base/regmap/regmap.c +2 -0
index fd377b956199..77cabde977ed 100644
@@ -1358,6 +1358,8 @@ int _regmap_raw_write(struct regmap *map, unsigned int reg,
 					     map->format.reg_bytes +
 					     map->format.pad_bytes,
 					     val, val_len);
+	else
+		ret = -ENOTSUPP;
 
 	/* If that didn't work fall back on linearising by hand. */
 	if (ret == -ENOTSUPP) {
Signature · 1 line
2.20.1
author maintainer
#28 lore raw

PATCH 29/53 bpf: silence warning messages in core

In reply to Sasha Levin

From: Valdis Klētnieks <[email protected]>

[ Upstream commit aee450cbe482a8c2f6fa5b05b178ef8b8ff107ca ]

Compiling kernel/bpf/core.c with W=1 causes a flood of warnings:

kernel/bpf/core.c:1198:65: warning: initialized field overwritten [-Woverride-init]
1198 | #define BPF_INSN_3_TBL(x, y, z) [BPF_##x | BPF_##y | BPF_##z] = true
| ^~~~
kernel/bpf/core.c:1087:2: note: in expansion of macro 'BPF_INSN_3_TBL'

 1087 |  INSN_3(ALU, ADD,  X),   \
      |  ^~~~~~
kernel/bpf/core.c:1202:3: note: in expansion of macro 'BPF_INSN_MAP'
 1202 |   BPF_INSN_MAP(BPF_INSN_2_TBL, BPF_INSN_3_TBL),
      |   ^~~~~~~~~~~~

kernel/bpf/core.c:1198:65: note: (near initialization for 'public_insntable[12]')
1198 | #define BPF_INSN_3_TBL(x, y, z) [BPF_##x | BPF_##y | BPF_##z] = true
| ^~~~
kernel/bpf/core.c:1087:2: note: in expansion of macro 'BPF_INSN_3_TBL'

 1087 |  INSN_3(ALU, ADD,  X),   \
      |  ^~~~~~
kernel/bpf/core.c:1202:3: note: in expansion of macro 'BPF_INSN_MAP'
 1202 |   BPF_INSN_MAP(BPF_INSN_2_TBL, BPF_INSN_3_TBL),
      |   ^~~~~~~~~~~~

98 copies of the above.

The attached patch silences the warnings, because we *know* we're overwriting the default initializer. That leaves bpf/core.c with only 6 other warnings, which become more visible in comparison.

---
 kernel/bpf/Makefile | 1 +
 1 file changed, 1 insertion(+)
kernel/bpf/Makefile +1 -0
index 13272582eee0..677991f29d66 100644
@@ -1,4 +1,5 @@
 obj-y := core.o
+CFLAGS_core.o += $(call cc-disable-warning, override-init)
 
 obj-$(CONFIG_BPF_SYSCALL) += syscall.o verifier.o inode.o helpers.o
 obj-$(CONFIG_BPF_SYSCALL) += hashtab.o arraymap.o
Signature · 1 line
2.20.1
author maintainer
#29 lore raw

PATCH 30/53 rcu: Force inlining of rcu_read_lock()

In reply to Sasha Levin

From: Waiman Long <[email protected]>

[ Upstream commit 6da9f775175e516fc7229ceaa9b54f8f56aa7924 ]

When debugging options are turned on, the rcu_read_lock() function might not be inlined. This results in lockdep's print_lock() function printing "rcu_read_lock+0x0/0x70" instead of rcu_read_lock()'s caller. For example:

[   10.579995] =============================
[   10.584033] WARNING: suspicious RCU usage
[   10.588074] 4.18.0.memcg_v2+ #1 Not tainted
[   10.593162] -----------------------------
[   10.597203] include/linux/rcupdate.h:281 Illegal context switch in
RCU read-side critical section!
[   10.606220]
[   10.606220] other info that might help us debug this:
[   10.606220]
[   10.614280]
[   10.614280] rcu_scheduler_active = 2, debug_locks = 1
[   10.620853] 3 locks held by systemd/1:
[   10.624632]  #0: (____ptrval____) (&type->i_mutex_dir_key#5){.+.+}, at: lookup_slow+0x42/0x70
[   10.633232]  #1: (____ptrval____) (rcu_read_lock){....}, at: rcu_read_lock+0x0/0x70
[   10.640954]  #2: (____ptrval____) (rcu_read_lock){....}, at: rcu_read_lock+0x0/0x70

These "rcu_read_lock+0x0/0x70" strings are not providing any useful information. This commit therefore forces inlining of the rcu_read_lock() function so that rcu_read_lock()'s caller is instead shown.

---
 include/linux/rcupdate.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
include/linux/rcupdate.h +1 -1
index addd03641e1a..0a93e9d1708e 100644
@@ -852,7 +852,7 @@ static inline void rcu_preempt_sleep_check(void)
  * read-side critical sections may be preempted and they may also block, but
  * only when acquiring spinlocks that are subject to priority inheritance.
  */
-static inline void rcu_read_lock(void)
+static __always_inline void rcu_read_lock(void)
 {
 	__rcu_read_lock();
 	__acquire(RCU);
Signature · 1 line
2.20.1
author maintainer
#30 lore raw

PATCH 31/53 xfrm: fix sa selector validation

In reply to Sasha Levin

From: Nicolas Dichtel <[email protected]>

[ Upstream commit b8d6d0079757cbd1b69724cfd1c08e2171c68cee ]

After commit b38ff4075a80, the following command does not work anymore:

$ ip xfrm state add src 10.125.0.2 dst 10.125.0.1 proto esp spi 34 reqid 1 \
  mode tunnel enc 'cbc(aes)' 0xb0abdba8b782ad9d364ec81e3a7d82a1 auth-trunc \
  'hmac(sha1)' 0xe26609ebd00acb6a4d51fca13e49ea78a72c73e6 96 flag align4

In fact, the selector is not mandatory, allow the user to provide an empty selector.

Fixes b38ff4075a80 ("xfrm: Fix xfrm sel prefix length validation")
CC Anirudh Gupta <[email protected]>
---
 net/xfrm/xfrm_user.c | 3 +++
 1 file changed, 3 insertions(+)
net/xfrm/xfrm_user.c +3 -0
index 10fda9a39cc2..8cc2a9df84fd 100644
@@ -166,6 +166,9 @@ static int verify_newsa_info(struct xfrm_usersa_info *p,
 	}
 
 	switch (p->sel.family) {
+	case AF_UNSPEC:
+		break;
+
 	case AF_INET:
 		if (p->sel.prefixlen_d > 32 || p->sel.prefixlen_s > 32)
 			goto out;
Signature · 1 line
2.20.1
author maintainer
#31 lore raw

PATCH 32/53 perf evsel: Make perf_evsel__name() accept a NULL argument

In reply to Sasha Levin

From: Arnaldo Carvalho de Melo <[email protected]>

[ Upstream commit fdbdd7e8580eac9bdafa532746c865644d125e34 ]

In which case it simply returns "unknown", like when it can't figure out the evsel->name value.

This makes this code more robust and fixes a problem in 'perf trace' where a NULL evsel was being passed to a routine that only used the evsel for printing its name when a invalid syscall id was passed.

---
 tools/perf/util/evsel.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)
tools/perf/util/evsel.c +7 -1
index 97fde9275f42..a8507fee654b 100644
@@ -491,6 +491,9 @@ const char *perf_evsel__name(struct perf_evsel *evsel)
 {
 	char bf[128];
 
+	if (!evsel)
+		goto out_unknown;
+
 	if (evsel->name)
 		return evsel->name;
 
@@ -527,7 +530,10 @@ const char *perf_evsel__name(struct perf_evsel *evsel)
 
 	evsel->name = strdup(bf);
 
-	return evsel->name ?: "unknown";
+	if (evsel->name)
+		return evsel->name;
+out_unknown:
+	return "unknown";
 }
 
 const char *perf_evsel__group_name(struct perf_evsel *evsel)
Signature · 1 line
2.20.1
author maintainer
#32 lore raw

PATCH 33/53 vhost_net: disable zerocopy by default

In reply to Sasha Levin

From: Jason Wang <[email protected]>

[ Upstream commit 098eadce3c622c07b328d0a43dda379b38cf7c5e ]

Vhost_net was known to suffer from HOL[1] issues which is not easy to fix. Several downstream disable the feature by default. What's more, the datapath was split and datacopy path got the support of batching and XDP support recently which makes it faster than zerocopy part for small packets transmission.

It looks to me that disable zerocopy by default is more appropriate. It cold be enabled by default again in the future if we fix the above issues.

[1] https://patchwork.kernel.org/patch/3787671/

---
 drivers/vhost/net.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/vhost/net.c +1 -1
index 645b2197930e..f46317135224 100644
@@ -30,7 +30,7 @@
 
 #include "vhost.h"
 
-static int experimental_zcopytx = 1;
+static int experimental_zcopytx = 0;
 module_param(experimental_zcopytx, int, 0444);
 MODULE_PARM_DESC(experimental_zcopytx, "Enable Zero Copy TX;"
 		                       " 1 -Enable; 0 - Disable");
Signature · 1 line
2.20.1
author maintainer
#33 lore raw

PATCH 34/53 EDAC/sysfs: Fix memory leak when creating a csrow object

In reply to Sasha Levin

From: Pan Bian <[email protected]>

[ Upstream commit 585fb3d93d32dbe89e718b85009f9c322cc554cd ]

In edac_create_csrow_object(), the reference to the object is not released when adding the device to the device hierarchy fails (device_add()). This may result in a memory leak.

---
 drivers/edac/edac_mc_sysfs.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)
drivers/edac/edac_mc_sysfs.c +7 -1
index 3c8f19f5ac81..0c53f2d54765 100644
@@ -426,6 +426,8 @@ static inline int nr_pages_per_csrow(struct csrow_info *csrow)
 static int edac_create_csrow_object(struct mem_ctl_info *mci,
 				    struct csrow_info *csrow, int index)
 {
+	int err;
+
 	csrow->dev.type = &csrow_attr_type;
 	csrow->dev.bus = mci->bus;
 	csrow->dev.groups = csrow_dev_groups;
@@ -438,7 +440,11 @@ static int edac_create_csrow_object(struct mem_ctl_info *mci,
 	edac_dbg(0, "creating (virtual) csrow node %s\n",
 		 dev_name(&csrow->dev));
 
-	return device_add(&csrow->dev);
+	err = device_add(&csrow->dev);
+	if (err)
+		put_device(&csrow->dev);
+
+	return err;
 }
 
 /* Create a CSROW object under specifed edac_mc_device */
Signature · 1 line
2.20.1
author maintainer
#34 lore raw

PATCH 35/53 media: i2c: fix warning same module names

In reply to Sasha Levin

From: Anders Roxell <[email protected]>

[ Upstream commit b2ce5617dad254230551feda3599f2cc68e53ad8 ]

When building with CONFIG_VIDEO_ADV7511 and CONFIG_DRM_I2C_ADV7511 enabled as loadable modules, we see the following warning:

drivers/gpu/drm/bridge/adv7511/adv7511.ko
drivers/media/i2c/adv7511.ko

Rework so that the file is named adv7511-v4l2.c.

---
 drivers/media/i2c/Makefile                      | 2 +-
 drivers/media/i2c/{adv7511.c => adv7511-v4l2.c} | 5 +++++
 2 files changed, 6 insertions(+), 1 deletion(-)
 rename drivers/media/i2c/{adv7511.c => adv7511-v4l2.c} (99%)
drivers/media/i2c/Makefile +1 -1
index 07db257abfc1..d5711def1fff 100644
@@ -28,7 +28,7 @@ obj-$(CONFIG_VIDEO_ADV7393) += adv7393.o
 obj-$(CONFIG_VIDEO_ADV7604) += adv7604.o
 obj-$(CONFIG_VIDEO_ADV7842) += adv7842.o
 obj-$(CONFIG_VIDEO_AD9389B) += ad9389b.o
-obj-$(CONFIG_VIDEO_ADV7511) += adv7511.o
+obj-$(CONFIG_VIDEO_ADV7511) += adv7511-v4l2.o
 obj-$(CONFIG_VIDEO_VPX3220) += vpx3220.o
 obj-$(CONFIG_VIDEO_VS6624)  += vs6624.o
 obj-$(CONFIG_VIDEO_BT819) += bt819.o
drivers/media/i2c/adv7511-v4l2.c renamed from drivers/media/i2c/adv7511.c +5 -0
similarity index 99%
rename from drivers/media/i2c/adv7511.c
rename to drivers/media/i2c/adv7511-v4l2.c
index c24839cfcc35..b35400e4e9af 100644
@@ -17,6 +17,11 @@
  * SOFTWARE.
  */
 
+/*
+ * This file is named adv7511-v4l2.c so it doesn't conflict with the Analog
+ * Device ADV7511 (config fragment CONFIG_DRM_I2C_ADV7511).
+ */
+
 
 #include <linux/kernel.h>
 #include <linux/module.h>
Signature · 1 line
2.20.1
author maintainer
#35 lore raw

PATCH 36/53 ntp: Limit TAI-UTC offset

In reply to Sasha Levin

From: Miroslav Lichvar <[email protected]>

[ Upstream commit d897a4ab11dc8a9fda50d2eccc081a96a6385998 ]

Don't allow the TAI-UTC offset of the system clock to be set by adjtimex() to a value larger than 100000 seconds.

This prevents an overflow in the conversion to int, prevents the CLOCK_TAI clock from getting too far ahead of the CLOCK_REALTIME clock, and it is still large enough to allow leap seconds to be inserted at the maximum rate currently supported by the kernel (once per day) for the next ~270 years, however unlikely it is that someone can survive a catastrophic event which slowed down the rotation of the Earth so much.

---
 kernel/time/ntp.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)
kernel/time/ntp.c +3 -1
index 0e0dc5d89911..bbe767b1f454 100644
@@ -39,6 +39,7 @@ static u64			tick_length_base;
 #define MAX_TICKADJ		500LL		/* usecs */
 #define MAX_TICKADJ_SCALED \
 	(((MAX_TICKADJ * NSEC_PER_USEC) << NTP_SCALE_SHIFT) / NTP_INTERVAL_FREQ)
+#define MAX_TAI_OFFSET		100000
 
 /*
  * phase-lock loop variables
@@ -633,7 +634,8 @@ static inline void process_adjtimex_modes(struct timex *txc,
 		time_constant = max(time_constant, 0l);
 	}
 
-	if (txc->modes & ADJ_TAI && txc->constant >= 0)
+	if (txc->modes & ADJ_TAI &&
+			txc->constant >= 0 && txc->constant <= MAX_TAI_OFFSET)
 		*time_tai = txc->constant;
 
 	if (txc->modes & ADJ_OFFSET)
Signature · 1 line
2.20.1
author maintainer
#36 lore raw

PATCH 37/53 timer_list: Guard procfs specific code

In reply to Sasha Levin

From: Nathan Huckleberry <[email protected]>

[ Upstream commit a9314773a91a1d3b36270085246a6715a326ff00 ]

With CONFIG_PROC_FS=n the following warning is emitted:

kernel/time/timer_list.c:361:36: warning: unused variable 'timer_list_sops' [-Wunused-const-variable]
static const struct seq_operations timer_list_sops = {

Add #ifdef guard around procfs specific code.

---
 kernel/time/timer_list.c | 36 +++++++++++++++++++-----------------
 1 file changed, 19 insertions(+), 17 deletions(-)
kernel/time/timer_list.c +19 -17
index 1407ed20ea93..b7c5d230b4b2 100644
@@ -299,23 +299,6 @@ static inline void timer_list_header(struct seq_file *m, u64 now)
 	SEQ_printf(m, "\n");
 }
 
-static int timer_list_show(struct seq_file *m, void *v)
-{
-	struct timer_list_iter *iter = v;
-
-	if (iter->cpu == -1 && !iter->second_pass)
-		timer_list_header(m, iter->now);
-	else if (!iter->second_pass)
-		print_cpu(m, iter->cpu, iter->now);
-#ifdef CONFIG_GENERIC_CLOCKEVENTS
-	else if (iter->cpu == -1 && iter->second_pass)
-		timer_list_show_tickdevices_header(m);
-	else
-		print_tickdevice(m, tick_get_device(iter->cpu), iter->cpu);
-#endif
-	return 0;
-}
-
 void sysrq_timer_list_show(void)
 {
 	u64 now = ktime_to_ns(ktime_get());
@@ -334,6 +317,24 @@ void sysrq_timer_list_show(void)
 	return;
 }
 
+#ifdef CONFIG_PROC_FS
+static int timer_list_show(struct seq_file *m, void *v)
+{
+	struct timer_list_iter *iter = v;
+
+	if (iter->cpu == -1 && !iter->second_pass)
+		timer_list_header(m, iter->now);
+	else if (!iter->second_pass)
+		print_cpu(m, iter->cpu, iter->now);
+#ifdef CONFIG_GENERIC_CLOCKEVENTS
+	else if (iter->cpu == -1 && iter->second_pass)
+		timer_list_show_tickdevices_header(m);
+	else
+		print_tickdevice(m, tick_get_device(iter->cpu), iter->cpu);
+#endif
+	return 0;
+}
+
 static void *move_iter(struct timer_list_iter *iter, loff_t offset)
 {
 	for (; offset; offset--) {
@@ -405,3 +406,4 @@ static int __init init_timer_list_procfs(void)
 	return 0;
 }
 __initcall(init_timer_list_procfs);
+#endif
Signature · 1 line
2.20.1
author maintainer
#37 lore raw

PATCH 38/53 acpi/arm64: ignore 5.1 FADTs that are reported as 5.0

In reply to Sasha Levin

From: Ard Biesheuvel <[email protected]>

[ Upstream commit 2af22f3ec3ca452f1e79b967f634708ff01ced8a ]

Some Qualcomm Snapdragon based laptops built to run Microsoft Windows are clearly ACPI 5.1 based, given that that is the first ACPI revision that supports ARM, and introduced the FADT 'arm_boot_flags' field, which has a non-zero field on those systems.

So in these cases, infer from the ARM boot flags that the FADT must be 5.1 or later, and treat it as 5.1.

---
 arch/arm64/kernel/acpi.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)
arch/arm64/kernel/acpi.c +7 -3
index d1ce8e2f98b9..4d0577d09681 100644
@@ -141,10 +141,14 @@ static int __init acpi_fadt_sanity_check(void)
 	 */
 	if (table->revision < 5 ||
 	   (table->revision == 5 && fadt->minor_revision < 1)) {
-		pr_err("Unsupported FADT revision %d.%d, should be 5.1+\n",
+		pr_err(FW_BUG "Unsupported FADT revision %d.%d, should be 5.1+\n",
 		       table->revision, fadt->minor_revision);
-		ret = -EINVAL;
-		goto out;
+
+		if (!fadt->arm_boot_flags) {
+			ret = -EINVAL;
+			goto out;
+		}
+		pr_err("FADT has ARM boot flags set, assuming 5.1\n");
 	}
 
 	if (!(fadt->flags & ACPI_FADT_HW_REDUCED)) {
Signature · 1 line
2.20.1
author maintainer
#38 lore raw

PATCH 39/53 media: coda: fix mpeg2 sequence number handling

In reply to Sasha Levin

From: Philipp Zabel <[email protected]>

[ Upstream commit 56d159a4ec6d8da7313aac6fcbb95d8fffe689ba ]

Sequence number handling assumed that the BIT processor frame number starts counting at 1, but this is not true for the MPEG-2 decoder, which starts at 0. Fix the sequence counter offset detection to handle this.

---
 drivers/media/platform/coda/coda-bit.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/media/platform/coda/coda-bit.c +4 -1
index a4639813cf35..a7ed2dba7a0e 100644
@@ -1581,6 +1581,7 @@ static int __coda_start_decoding(struct coda_ctx *ctx)
 		coda_write(dev, 0, CODA_REG_BIT_BIT_STREAM_PARAM);
 		return -ETIMEDOUT;
 	}
+	ctx->sequence_offset = ~0U;
 	ctx->initialized = 1;
 
 	/* Update kfifo out pointer from coda bitstream read pointer */
@@ -1971,7 +1972,9 @@ static void coda_finish_decode(struct coda_ctx *ctx)
 		v4l2_err(&dev->v4l2_dev,
 			 "decoded frame index out of range: %d\n", decoded_idx);
 	} else {
-		val = coda_read(dev, CODA_RET_DEC_PIC_FRAME_NUM) - 1;
+		val = coda_read(dev, CODA_RET_DEC_PIC_FRAME_NUM);
+		if (ctx->sequence_offset == -1)
+			ctx->sequence_offset = val;
 		val -= ctx->sequence_offset;
 		spin_lock_irqsave(&ctx->buffer_meta_lock, flags);
 		if (!list_empty(&ctx->buffer_meta_list)) {
Signature · 1 line
2.20.1
author maintainer
#39 lore raw

PATCH 40/53 media: coda: increment sequence offset for the last returned frame

In reply to Sasha Levin

From: Philipp Zabel <[email protected]>

[ Upstream commit b3b7d96817cdb8b6fc353867705275dce8f41ccc ]

If no more frames are decoded in bitstream end mode, and a previously decoded frame has been returned, the firmware still increments the frame number. To avoid a sequence number mismatch after decoder restart, increment the sequence_offset correction parameter.

---
 drivers/media/platform/coda/coda-bit.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/media/platform/coda/coda-bit.c +3 -0
index a7ed2dba7a0e..b19e70b83f4a 100644
@@ -1967,6 +1967,9 @@ static void coda_finish_decode(struct coda_ctx *ctx)
 		else if (ctx->display_idx < 0)
 			ctx->hold = true;
 	} else if (decoded_idx == -2) {
+		if (ctx->display_idx >= 0 &&
+		    ctx->display_idx < ctx->num_internal_frames)
+			ctx->sequence_offset++;
 		/* no frame was decoded, we still return remaining buffers */
 	} else if (decoded_idx < 0 || decoded_idx >= ctx->num_internal_frames) {
 		v4l2_err(&dev->v4l2_dev,
Signature · 1 line
2.20.1
author maintainer
#40 lore raw

PATCH 41/53 mt7601u: do not schedule rx_tasklet when the device has been disconnected

In reply to Sasha Levin

From: Lorenzo Bianconi <[email protected]>

[ Upstream commit 4079e8ccabc3b6d1b503f2376123cb515d14921f ]

Do not schedule rx_tasklet when the usb dongle is disconnected. Moreover do not grub rx_lock in mt7601u_kill_rx since usb_poison_urb can run concurrently with urb completion and we can unlink urbs from rx ring in any order.
This patch fixes the common kernel warning reported when
the device is removed.

[   24.921354] usb 3-14: USB disconnect, device number 7
[   24.921593] ------------[ cut here ]------------
[   24.921594] RX urb mismatch
[   24.921675] WARNING: CPU: 4 PID: 163 at drivers/net/wireless/mediatek/mt7601u/dma.c:200 mt7601u_complete_rx+0xcb/0xd0 [mt7601u]
[   24.921769] CPU: 4 PID: 163 Comm: kworker/4:2 Tainted: G           OE     4.19.31-041931-generic #201903231635
[   24.921770] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./Z97 Extreme4, BIOS P1.30 05/23/2014
[   24.921782] Workqueue: usb_hub_wq hub_event
[   24.921797] RIP: 0010:mt7601u_complete_rx+0xcb/0xd0 [mt7601u]
[   24.921800] RSP: 0018:ffff9bd9cfd03d08 EFLAGS: 00010086
[   24.921802] RAX: 0000000000000000 RBX: ffff9bd9bf043540 RCX: 0000000000000006
[   24.921803] RDX: 0000000000000007 RSI: 0000000000000096 RDI: ffff9bd9cfd16420
[   24.921804] RBP: ffff9bd9cfd03d28 R08: 0000000000000002 R09: 00000000000003a8
[   24.921805] R10: 0000002f485fca34 R11: 0000000000000000 R12: ffff9bd9bf043c1c
[   24.921806] R13: ffff9bd9c62fa3c0 R14: 0000000000000082 R15: 0000000000000000
[   24.921807] FS:  0000000000000000(0000) GS:ffff9bd9cfd00000(0000) knlGS:0000000000000000
[   24.921808] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   24.921808] CR2: 00007fb2648b0000 CR3: 0000000142c0a004 CR4: 00000000001606e0
[   24.921809] Call Trace:
[   24.921812]  <IRQ>
[   24.921819]  __usb_hcd_giveback_urb+0x8b/0x140
[   24.921821]  usb_hcd_giveback_urb+0xca/0xe0
[   24.921828]  xhci_giveback_urb_in_irq.isra.42+0x82/0xf0
[   24.921834]  handle_cmd_completion+0xe02/0x10d0
[   24.921837]  xhci_irq+0x274/0x4a0
[   24.921838]  xhci_msi_irq+0x11/0x20
[   24.921851]  __handle_irq_event_percpu+0x44/0x190
[   24.921856]  handle_irq_event_percpu+0x32/0x80
[   24.921861]  handle_irq_event+0x3b/0x5a
[   24.921867]  handle_edge_irq+0x80/0x190
[   24.921874]  handle_irq+0x20/0x30
[   24.921889]  do_IRQ+0x4e/0xe0
[   24.921891]  common_interrupt+0xf/0xf
[   24.921892]  </IRQ>
[   24.921900] RIP: 0010:usb_hcd_flush_endpoint+0x78/0x180
[   24.921354] usb 3-14: USB disconnect, device number 7
---
 drivers/net/wireless/mediatek/mt7601u/dma.c | 33 +++++++++++----------
 1 file changed, 18 insertions(+), 15 deletions(-)
drivers/net/wireless/mediatek/mt7601u/dma.c +18 -15
index 57a80cfa39b1..6ba30129a3d8 100644
@@ -193,10 +193,23 @@ static void mt7601u_complete_rx(struct urb *urb)
 	struct mt7601u_rx_queue *q = &dev->rx_q;
 	unsigned long flags;
 
-	spin_lock_irqsave(&dev->rx_lock, flags);
+	/* do no schedule rx tasklet if urb has been unlinked
+	 * or the device has been removed
+	 */
+	switch (urb->status) {
+	case -ECONNRESET:
+	case -ESHUTDOWN:
+	case -ENOENT:
+		return;
+	default:
+		dev_err_ratelimited(dev->dev, "rx urb failed: %d\n",
+				    urb->status);
+		/* fall through */
+	case 0:
+		break;
+	}
 
-	if (mt7601u_urb_has_error(urb))
-		dev_err(dev->dev, "Error: RX urb failed:%d\n", urb->status);
+	spin_lock_irqsave(&dev->rx_lock, flags);
 	if (WARN_ONCE(q->e[q->end].urb != urb, "RX urb mismatch"))
 		goto out;
 
@@ -363,19 +376,9 @@ int mt7601u_dma_enqueue_tx(struct mt7601u_dev *dev, struct sk_buff *skb,
 static void mt7601u_kill_rx(struct mt7601u_dev *dev)
 {
 	int i;
-	unsigned long flags;
 
-	spin_lock_irqsave(&dev->rx_lock, flags);
-
-	for (i = 0; i < dev->rx_q.entries; i++) {
-		int next = dev->rx_q.end;
-
-		spin_unlock_irqrestore(&dev->rx_lock, flags);
-		usb_poison_urb(dev->rx_q.e[next].urb);
-		spin_lock_irqsave(&dev->rx_lock, flags);
-	}
-
-	spin_unlock_irqrestore(&dev->rx_lock, flags);
+	for (i = 0; i < dev->rx_q.entries; i++)
+		usb_poison_urb(dev->rx_q.e[i].urb);
 }
 
 static int mt7601u_submit_rx_buf(struct mt7601u_dev *dev,
Signature · 1 line
2.20.1
author maintainer
#41 lore raw

PATCH 42/53 x86/build: Add 'set -e' to mkcapflags.sh to delete broken capflags.c

In reply to Sasha Levin

From: Masahiro Yamada <[email protected]>

[ Upstream commit bc53d3d777f81385c1bb08b07bd1c06450ecc2c1 ]

Without 'set -e', shell scripts continue running even after any error occurs. The missed 'set -e' is a typical bug in shell scripting.

For example, when a disk space shortage occurs while this script is running, it actually ends up with generating a truncated capflags.c.

Yet, mkcapflags.sh continues running and exits with 0. So, the build system assumes it has succeeded.

It will not be re-generated in the next invocation of Make since its timestamp is newer than that of any of the source files.

Add 'set -e' so that any error in this script is caught and propagated to the build system.

Since 9c2af1c7377a ("kbuild: add .DELETE_ON_ERROR special target"), make automatically deletes the target on any failure. So, the broken capflags.c will be deleted automatically.

---
 arch/x86/kernel/cpu/mkcapflags.sh | 2 ++
 1 file changed, 2 insertions(+)
arch/x86/kernel/cpu/mkcapflags.sh +2 -0
index 6988c74409a8..711b74e0e623 100644
@@ -3,6 +3,8 @@
 # Generate the x86_cap/bug_flags[] arrays from include/asm/cpufeatures.h
 #
 
+set -e
+
 IN=$1
 OUT=$2
 
Signature · 1 line
2.20.1
author maintainer
#42 lore raw

PATCH 43/53 mt7601u: fix possible memory leak when the device is disconnected

In reply to Sasha Levin

From: Lorenzo Bianconi <[email protected]>

[ Upstream commit 23377c200b2eb48a60d0f228b2a2e75ed6ee6060 ]

When the device is disconnected while passing traffic it is possible to receive out of order urbs causing a memory leak since the skb linked to the current tx urb is not removed. Fix the issue deallocating the skb cleaning up the tx ring. Moreover this patch fixes the following kernel warning

[   57.480771] usb 1-1: USB disconnect, device number 2
[   57.483451] ------------[ cut here ]------------
[   57.483462] TX urb mismatch
[   57.483481] WARNING: CPU: 1 PID: 32 at drivers/net/wireless/mediatek/mt7601u/dma.c:245 mt7601u_complete_tx+0x165/00
[   57.483483] Modules linked in:
[   57.483496] CPU: 1 PID: 32 Comm: kworker/1:1 Not tainted 5.2.0-rc1+ #72
[   57.483498] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.12.0-2.fc30 04/01/2014
[   57.483502] Workqueue: usb_hub_wq hub_event
[   57.483507] RIP: 0010:mt7601u_complete_tx+0x165/0x1e0
[   57.483510] Code: 8b b5 10 04 00 00 8b 8d 14 04 00 00 eb 8b 80 3d b1 cb e1 00 00 75 9e 48 c7 c7 a4 ea 05 82 c6 05 f
[   57.483513] RSP: 0000:ffffc900000a0d28 EFLAGS: 00010092
[   57.483516] RAX: 000000000000000f RBX: ffff88802c0a62c0 RCX: ffffc900000a0c2c
[   57.483518] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff810a8371
[   57.483520] RBP: ffff88803ced6858 R08: 0000000000000000 R09: 0000000000000001
[   57.483540] R10: 0000000000000002 R11: 0000000000000000 R12: 0000000000000046
[   57.483542] R13: ffff88802c0a6c88 R14: ffff88803baab540 R15: ffff88803a0cc078
[   57.483548] FS:  0000000000000000(0000) GS:ffff88803eb00000(0000) knlGS:0000000000000000
[   57.483550] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   57.483552] CR2: 000055e7f6780100 CR3: 0000000028c86000 CR4: 00000000000006a0
[   57.483554] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   57.483556] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   57.483559] Call Trace:
[   57.483561]  <IRQ>
[   57.483565]  __usb_hcd_giveback_urb+0x77/0xe0
[   57.483570]  xhci_giveback_urb_in_irq.isra.0+0x8b/0x140
[   57.483574]  handle_cmd_completion+0xf5b/0x12c0
[   57.483577]  xhci_irq+0x1f6/0x1810
[   57.483581]  ? lockdep_hardirqs_on+0x9e/0x180
[   57.483584]  ? _raw_spin_unlock_irq+0x24/0x30
[   57.483588]  __handle_irq_event_percpu+0x3a/0x260
[   57.483592]  handle_irq_event_percpu+0x1c/0x60
[   57.483595]  handle_irq_event+0x2f/0x4c
[   57.483599]  handle_edge_irq+0x7e/0x1a0
[   57.483603]  handle_irq+0x17/0x20
[   57.483607]  do_IRQ+0x54/0x110
[   57.483610]  common_interrupt+0xf/0xf
[   57.483612]  </IRQ>
---
 drivers/net/wireless/mediatek/mt7601u/dma.c | 21 ++++++++++++++++-----
 drivers/net/wireless/mediatek/mt7601u/tx.c  |  4 ++--
 2 files changed, 18 insertions(+), 7 deletions(-)
drivers/net/wireless/mediatek/mt7601u/dma.c +16 -5
index 6ba30129a3d8..3d0b9324d5bf 100644
@@ -241,14 +241,25 @@ static void mt7601u_complete_tx(struct urb *urb)
 	struct sk_buff *skb;
 	unsigned long flags;
 
-	spin_lock_irqsave(&dev->tx_lock, flags);
+	switch (urb->status) {
+	case -ECONNRESET:
+	case -ESHUTDOWN:
+	case -ENOENT:
+		return;
+	default:
+		dev_err_ratelimited(dev->dev, "tx urb failed: %d\n",
+				    urb->status);
+		/* fall through */
+	case 0:
+		break;
+	}
 
-	if (mt7601u_urb_has_error(urb))
-		dev_err(dev->dev, "Error: TX urb failed:%d\n", urb->status);
+	spin_lock_irqsave(&dev->tx_lock, flags);
 	if (WARN_ONCE(q->e[q->start].urb != urb, "TX urb mismatch"))
 		goto out;
 
 	skb = q->e[q->start].skb;
+	q->e[q->start].skb = NULL;
 	trace_mt_tx_dma_done(dev, skb);
 
 	__skb_queue_tail(&dev->tx_skb_done, skb);
@@ -448,10 +459,10 @@ static void mt7601u_free_tx_queue(struct mt7601u_tx_queue *q)
 {
 	int i;
 
-	WARN_ON(q->used);
-
 	for (i = 0; i < q->entries; i++)  {
 		usb_poison_urb(q->e[i].urb);
+		if (q->e[i].skb)
+			mt7601u_tx_status(q->dev, q->e[i].skb);
 		usb_free_urb(q->e[i].urb);
 	}
 }
drivers/net/wireless/mediatek/mt7601u/tx.c +2 -2
index a0a33dc8f6bc..a1b6db2a8937 100644
@@ -117,9 +117,9 @@ void mt7601u_tx_status(struct mt7601u_dev *dev, struct sk_buff *skb)
 	info->status.rates[0].idx = -1;
 	info->flags |= IEEE80211_TX_STAT_ACK;
 
-	spin_lock(&dev->mac_lock);
+	spin_lock_bh(&dev->mac_lock);
 	ieee80211_tx_status(dev->hw, skb);
-	spin_unlock(&dev->mac_lock);
+	spin_unlock_bh(&dev->mac_lock);
 }
 
 static int mt7601u_skb_rooms(struct mt7601u_dev *dev, struct sk_buff *skb)
Signature · 1 line
2.20.1
author maintainer
#43 lore raw

PATCH 44/53 ath10k: fix PCIE device wake up failed

In reply to Sasha Levin

From: Miaoqing Pan <[email protected]>

[ Upstream commit 011d4111c8c602ea829fa4917af1818eb0500a90 ]

Observed PCIE device wake up failed after ~120 iterations of soft-reboot test. The error message is
"ath10k_pci 0000:01:00.0: failed to wake up device : -110"

The call trace as below:
ath10k_pci_probe -> ath10k_pci_force_wake -> ath10k_pci_wake_wait -> ath10k_pci_is_awake

Once trigger the device to wake up, we will continuously check the RTC state until it returns RTC_STATE_V_ON or timeout.

But for QCA99x0 chips, we use wrong value for RTC_STATE_V_ON. Occasionally, we get 0x7 on the fist read, we thought as a failure case, but actually is the right value, also verified with the spec. So fix the issue by changing RTC_STATE_V_ON from 0x5 to 0x7, passed ~2000 iterations.

Tested HW: QCA9984

---
 drivers/net/wireless/ath/ath10k/hw.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/wireless/ath/ath10k/hw.c +1 -1
index 7b84d08a5154..12d6549e45a1 100644
@@ -128,7 +128,7 @@ const struct ath10k_hw_values qca6174_values = {
 };
 
 const struct ath10k_hw_values qca99x0_values = {
-	.rtc_state_val_on		= 5,
+	.rtc_state_val_on		= 7,
 	.ce_count			= 12,
 	.msi_assign_ce_max		= 12,
 	.num_target_ce_config_wlan	= 10,
Signature · 7 lines
2.20.1


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
author maintainer
#44 lore raw

PATCH 45/53 rslib: Fix decoding of shortened codes

In reply to Sasha Levin

From: Ferdinand Blomqvist <[email protected]>

[ Upstream commit 2034a42d1747fc1e1eeef2c6f1789c4d0762cb9c ]

The decoding of shortenend codes is broken. It only works as expected if there are no erasures.

When decoding with erasures, Lambda (the error and erasure locator polynomial) is initialized from the given erasure positions. The pad parameter is not accounted for by the initialisation code, and hence Lambda is initialized from incorrect erasure positions.

The fix is to adjust the erasure positions by the supplied pad.

---
 lib/reed_solomon/decode_rs.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
lib/reed_solomon/decode_rs.c +2 -2
index 0ec3f257ffdf..8eed0f9ac495 100644
@@ -99,9 +99,9 @@
 	if (no_eras > 0) {
 		/* Init lambda to be the erasure locator polynomial */
 		lambda[1] = alpha_to[rs_modnn(rs,
-					      prim * (nn - 1 - eras_pos[0]))];
+					prim * (nn - 1 - (eras_pos[0] + pad)))];
 		for (i = 1; i < no_eras; i++) {
-			u = rs_modnn(rs, prim * (nn - 1 - eras_pos[i]));
+			u = rs_modnn(rs, prim * (nn - 1 - (eras_pos[i] + pad)));
 			for (j = i + 1; j > 0; j--) {
 				tmp = index_of[lambda[j - 1]];
 				if (tmp != nn) {
Signature · 1 line
2.20.1
author maintainer
#45 lore raw

PATCH 46/53 rslib: Fix handling of of caller provided syndrome

In reply to Sasha Levin

From: Ferdinand Blomqvist <[email protected]>

[ Upstream commit ef4d6a8556b637ad27c8c2a2cff1dda3da38e9a9 ]

Check if the syndrome provided by the caller is zero, and act accordingly.

---
 lib/reed_solomon/decode_rs.c | 14 ++++++++++++--
 1 file changed, 12 insertions(+), 2 deletions(-)
lib/reed_solomon/decode_rs.c +12 -2
index 8eed0f9ac495..a5d313381539 100644
@@ -42,8 +42,18 @@
 	BUG_ON(pad < 0 || pad >= nn);
 
 	/* Does the caller provide the syndrome ? */
-	if (s != NULL)
-		goto decode;
+	if (s != NULL) {
+		for (i = 0; i < nroots; i++) {
+			/* The syndrome is in index form,
+			 * so nn represents zero
+			 */
+			if (s[i] != nn)
+				goto decode;
+		}
+
+		/* syndrome is zero, no errors to correct  */
+		return 0;
+	}
 
 	/* form the syndromes; i.e., evaluate data(x) at roots of
 	 * g(x) */
Signature · 1 line
2.20.1
author maintainer
#46 lore raw

PATCH 47/53 ixgbe: Check DDM existence in transceiver before access

In reply to Sasha Levin

From: "Mauro S. M. Rodrigues" <[email protected]>

[ Upstream commit 655c91414579d7bb115a4f7898ee726fc18e0984 ]

Some transceivers may comply with SFF-8472 but not implement the Digital Diagnostic Monitoring (DDM) interface described in it. The existence of such area is specified by bit 6 of byte 92, set to 1 if implemented.

Currently, due to not checking this bit ixgbe fails trying to read SFP module's eeprom with the follow message:

ethtool -m enP51p1s0f0
Cannot get Module EEPROM data: Input/output error

Because it fails to read the additional 256 bytes in which it was assumed to exist the DDM data.

This issue was noticed using a Mellanox Passive DAC PN 01FT738. The eeprom data was confirmed by Mellanox as correct and present in other Passive DACs in from other manufacturers.

---
 drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c | 3 ++-
 drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h     | 1 +
 2 files changed, 3 insertions(+), 1 deletion(-)
drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c +2 -1
index d681273bd39d..9d38634071a4 100644
@@ -3133,7 +3133,8 @@ static int ixgbe_get_module_info(struct net_device *dev,
 		page_swap = true;
 	}
 
-	if (sff8472_rev == IXGBE_SFF_SFF_8472_UNSUP || page_swap) {
+	if (sff8472_rev == IXGBE_SFF_SFF_8472_UNSUP || page_swap ||
+	    !(addr_mode & IXGBE_SFF_DDM_IMPLEMENTED)) {
 		/* We have a SFP, but it does not support SFF-8472 */
 		modinfo->type = ETH_MODULE_SFF_8079;
 		modinfo->eeprom_len = ETH_MODULE_SFF_8079_LEN;
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h +1 -0
index 5abd66c84d00..7b7dc6d7d159 100644
@@ -70,6 +70,7 @@
 #define IXGBE_SFF_SOFT_RS_SELECT_10G		0x8
 #define IXGBE_SFF_SOFT_RS_SELECT_1G		0x0
 #define IXGBE_SFF_ADDRESSING_MODE		0x4
+#define IXGBE_SFF_DDM_IMPLEMENTED		0x40
 #define IXGBE_SFF_QSFP_DA_ACTIVE_CABLE		0x1
 #define IXGBE_SFF_QSFP_DA_PASSIVE_CABLE		0x8
 #define IXGBE_SFF_QSFP_CONNECTOR_NOT_SEPARABLE	0x23
Signature · 1 line
2.20.1
author maintainer
#47 lore raw

PATCH 48/53 EDAC: Fix global-out-of-bounds write when setting edac_mc_poll_msec

In reply to Sasha Levin

From: Eiichi Tsukata <[email protected]>

[ Upstream commit d8655e7630dafa88bc37f101640e39c736399771 ]

Commit 9da21b1509d8 ("EDAC: Poll timeout cannot be zero, p2") assumes edac_mc_poll_msec to be unsigned long, but the type of the variable still remained as int. Setting edac_mc_poll_msec can trigger out-of-bounds write.

Reproducer:

  # echo 1001 > /sys/module/edac_core/parameters/edac_mc_poll_msec

KASAN report:

  BUG: KASAN: global-out-of-bounds in edac_set_poll_msec+0x140/0x150
  Write of size 8 at addr ffffffffb91b2d00 by task bash/1996

  CPU: 1 PID: 1996 Comm: bash Not tainted 5.2.0-rc6+ #23
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-2.fc30 04/01/2014
  Call Trace:
   dump_stack+0xca/0x13e
   print_address_description.cold+0x5/0x246
   __kasan_report.cold+0x75/0x9a
   ? edac_set_poll_msec+0x140/0x150
   kasan_report+0xe/0x20
   edac_set_poll_msec+0x140/0x150
   ? dimmdev_location_show+0x30/0x30
   ? vfs_lock_file+0xe0/0xe0
   ? _raw_spin_lock+0x87/0xe0
   param_attr_store+0x1b5/0x310
   ? param_array_set+0x4f0/0x4f0
   module_attr_store+0x58/0x80
   ? module_attr_show+0x80/0x80
   sysfs_kf_write+0x13d/0x1a0
   kernfs_fop_write+0x2bc/0x460
   ? sysfs_kf_bin_read+0x270/0x270
   ? kernfs_notify+0x1f0/0x1f0
   __vfs_write+0x81/0x100
   vfs_write+0x1e1/0x560
   ksys_write+0x126/0x250
   ? __ia32_sys_read+0xb0/0xb0
   ? do_syscall_64+0x1f/0x390
   do_syscall_64+0xc1/0x390
   entry_SYSCALL_64_after_hwframe+0x49/0xbe
  RIP: 0033:0x7fa7caa5e970
  Code: 73 01 c3 48 8b 0d 28 d5 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 99 2d 2c 00 00 75 10 b8 01 00 00 00 04
  RSP: 002b:00007fff6acfdfe8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
  RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00007fa7caa5e970
  RDX: 0000000000000005 RSI: 0000000000e95c08 RDI: 0000000000000001
  RBP: 0000000000e95c08 R08: 00007fa7cad1e760 R09: 00007fa7cb36a700
  R10: 0000000000000073 R11: 0000000000000246 R12: 0000000000000005
  R13: 0000000000000001 R14: 00007fa7cad1d600 R15: 0000000000000005

  The buggy address belongs to the variable:
   edac_mc_poll_msec+0x0/0x40

  Memory state around the buggy address:
   ffffffffb91b2c00: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa
   ffffffffb91b2c80: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa
  >ffffffffb91b2d00: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
                     ^
   ffffffffb91b2d80: 04 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
   ffffffffb91b2e00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Fix it by changing the type of edac_mc_poll_msec to unsigned int. The reason why this patch adopts unsigned int rather than unsigned long is msecs_to_jiffies() assumes arg to be unsigned int. We can avoid integer conversion bugs and unsigned int will be large enough for edac_mc_poll_msec.

Fixes 9da21b1509d8 ("EDAC: Poll timeout cannot be zero, p2")
---
 drivers/edac/edac_mc_sysfs.c | 16 ++++++++--------
 drivers/edac/edac_module.h   |  2 +-
 2 files changed, 9 insertions(+), 9 deletions(-)
drivers/edac/edac_mc_sysfs.c +8 -8
index 0c53f2d54765..d459cf4b8579 100644
@@ -26,7 +26,7 @@
 static int edac_mc_log_ue = 1;
 static int edac_mc_log_ce = 1;
 static int edac_mc_panic_on_ue;
-static int edac_mc_poll_msec = 1000;
+static unsigned int edac_mc_poll_msec = 1000;
 
 /* Getter functions for above */
 int edac_mc_get_log_ue(void)
@@ -45,30 +45,30 @@ int edac_mc_get_panic_on_ue(void)
 }
 
 /* this is temporary */
-int edac_mc_get_poll_msec(void)
+unsigned int edac_mc_get_poll_msec(void)
 {
 	return edac_mc_poll_msec;
 }
 
 static int edac_set_poll_msec(const char *val, struct kernel_param *kp)
 {
-	unsigned long l;
+	unsigned int i;
 	int ret;
 
 	if (!val)
 		return -EINVAL;
 
-	ret = kstrtoul(val, 0, &l);
+	ret = kstrtouint(val, 0, &i);
 	if (ret)
 		return ret;
 
-	if (l < 1000)
+	if (i < 1000)
 		return -EINVAL;
 
-	*((unsigned long *)kp->arg) = l;
+	*((unsigned int *)kp->arg) = i;
 
 	/* notify edac_mc engine to reset the poll period */
-	edac_mc_reset_delay_period(l);
+	edac_mc_reset_delay_period(i);
 
 	return 0;
 }
@@ -82,7 +82,7 @@ MODULE_PARM_DESC(edac_mc_log_ue,
 module_param(edac_mc_log_ce, int, 0644);
 MODULE_PARM_DESC(edac_mc_log_ce,
 		 "Log correctable error to console: 0=off 1=on");
-module_param_call(edac_mc_poll_msec, edac_set_poll_msec, param_get_int,
+module_param_call(edac_mc_poll_msec, edac_set_poll_msec, param_get_uint,
 		  &edac_mc_poll_msec, 0644);
 MODULE_PARM_DESC(edac_mc_poll_msec, "Polling period in milliseconds");
 
drivers/edac/edac_module.h +1 -1
index b95a48fc723d..c7a7a0891eb6 100644
@@ -33,7 +33,7 @@ extern int edac_mc_get_log_ue(void);
 extern int edac_mc_get_log_ce(void);
 extern int edac_mc_get_panic_on_ue(void);
 extern int edac_get_poll_msec(void);
-extern int edac_mc_get_poll_msec(void);
+extern unsigned int edac_mc_get_poll_msec(void);
 
 unsigned edac_dimm_info_location(struct dimm_info *dimm, char *buf,
 				 unsigned len);
Signature · 1 line
2.20.1
author maintainer
#48 lore raw

PATCH 49/53 bcache: check c->gc_thread by IS_ERR_OR_NULL in cache_set_flush()

In reply to Sasha Levin

From: Coly Li <[email protected]>

[ Upstream commit b387e9b58679c60f5b1e4313939bd4878204fc37 ]

When system memory is in heavy pressure, bch_gc_thread_start() from run_cache_set() may fail due to out of memory. In such condition, c->gc_thread is assigned to -ENOMEM, not NULL pointer. Then in following failure code path bch_cache_set_error(), when cache_set_flush() gets called, the code piece to stop c->gc_thread is broken,

         if (!IS_ERR_OR_NULL(c->gc_thread))
                 kthread_stop(c->gc_thread);

And KASAN catches such NULL pointer deference problem, with the warning information:

[  561.207881] ==================================================================
[  561.207900] BUG: KASAN: null-ptr-deref in kthread_stop+0x3b/0x440
[  561.207904] Write of size 4 at addr 000000000000001c by task kworker/15:1/313
[  561.207913] CPU: 15 PID: 313 Comm: kworker/15:1 Tainted: G        W         5.0.0-vanilla+ #3
[  561.207916] Hardware name: Lenovo ThinkSystem SR650 -[7X05CTO1WW]-/-[7X05CTO1WW]-, BIOS -[IVE136T-2.10]- 03/22/2019
[  561.207935] Workqueue: events cache_set_flush [bcache]
[  561.207940] Call Trace:
[  561.207948]  dump_stack+0x9a/0xeb
[  561.207955]  ? kthread_stop+0x3b/0x440
[  561.207960]  ? kthread_stop+0x3b/0x440
[  561.207965]  kasan_report+0x176/0x192
[  561.207973]  ? kthread_stop+0x3b/0x440
[  561.207981]  kthread_stop+0x3b/0x440
[  561.207995]  cache_set_flush+0xd4/0x6d0 [bcache]
[  561.208008]  process_one_work+0x856/0x1620
[  561.208015]  ? find_held_lock+0x39/0x1d0
[  561.208028]  ? drain_workqueue+0x380/0x380
[  561.208048]  worker_thread+0x87/0xb80
[  561.208058]  ? __kthread_parkme+0xb6/0x180
[  561.208067]  ? process_one_work+0x1620/0x1620
[  561.208072]  kthread+0x326/0x3e0
[  561.208079]  ? kthread_create_worker_on_cpu+0xc0/0xc0
[  561.208090]  ret_from_fork+0x3a/0x50
[  561.208110] ==================================================================
[  561.208113] Disabling lock debugging due to kernel taint
[  561.208115] irq event stamp: 11800231
[  561.208126] hardirqs last  enabled at (11800231): [<ffffffff83008538>] do_syscall_64+0x18/0x410
[  561.208127] BUG: unable to handle kernel NULL pointer dereference at 000000000000001c
[  561.208129] #PF error: [WRITE]
[  561.312253] hardirqs last disabled at (11800230): [<ffffffff830052ff>] trace_hardirqs_off_thunk+0x1a/0x1c
[  561.312259] softirqs last  enabled at (11799832): [<ffffffff850005c7>] __do_softirq+0x5c7/0x8c3
[  561.405975] PGD 0 P4D 0
[  561.442494] softirqs last disabled at (11799821): [<ffffffff831add2c>] irq_exit+0x1ac/0x1e0
[  561.791359] Oops: 0002 [#1] SMP KASAN NOPTI
[  561.791362] CPU: 15 PID: 313 Comm: kworker/15:1 Tainted: G    B   W         5.0.0-vanilla+ #3
[  561.791363] Hardware name: Lenovo ThinkSystem SR650 -[7X05CTO1WW]-/-[7X05CTO1WW]-, BIOS -[IVE136T-2.10]- 03/22/2019
[  561.791371] Workqueue: events cache_set_flush [bcache]
[  561.791374] RIP: 0010:kthread_stop+0x3b/0x440
[  561.791376] Code: 00 00 65 8b 05 26 d5 e0 7c 89 c0 48 0f a3 05 ec aa df 02 0f 82 dc 02 00 00 4c 8d 63 20 be 04 00 00 00 4c 89 e7 e8 65 c5 53 00 <f0> ff 43 20 48 8d 7b 24 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48
[  561.791377] RSP: 0018:ffff88872fc8fd10 EFLAGS: 00010286
[  561.838895] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  561.838916] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  561.838934] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  561.838948] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  561.838966] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  561.838979] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  561.838996] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  563.067028] RAX: 0000000000000000 RBX: fffffffffffffffc RCX: ffffffff832dd314
[  563.067030] RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000297
[  563.067032] RBP: ffff88872fc8fe88 R08: fffffbfff0b8213d R09: fffffbfff0b8213d
[  563.067034] R10: 0000000000000001 R11: fffffbfff0b8213c R12: 000000000000001c
[  563.408618] R13: ffff88dc61cc0f68 R14: ffff888102b94900 R15: ffff88dc61cc0f68
[  563.408620] FS:  0000000000000000(0000) GS:ffff888f7dc00000(0000) knlGS:0000000000000000
[  563.408622] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  563.408623] CR2: 000000000000001c CR3: 0000000f48a1a004 CR4: 00000000007606e0
[  563.408625] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  563.408627] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  563.904795] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  563.915796] PKRU: 55555554
[  563.915797] Call Trace:
[  563.915807]  cache_set_flush+0xd4/0x6d0 [bcache]
[  563.915812]  process_one_work+0x856/0x1620
[  564.001226] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  564.033563]  ? find_held_lock+0x39/0x1d0
[  564.033567]  ? drain_workqueue+0x380/0x380
[  564.033574]  worker_thread+0x87/0xb80
[  564.062823] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  564.118042]  ? __kthread_parkme+0xb6/0x180
[  564.118046]  ? process_one_work+0x1620/0x1620
[  564.118048]  kthread+0x326/0x3e0
[  564.118050]  ? kthread_create_worker_on_cpu+0xc0/0xc0
[  564.167066] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  564.252441]  ret_from_fork+0x3a/0x50
[  564.252447] Modules linked in: msr rpcrdma sunrpc rdma_ucm ib_iser ib_umad rdma_cm ib_ipoib i40iw configfs iw_cm ib_cm libiscsi scsi_transport_iscsi mlx4_ib ib_uverbs mlx4_en ib_core nls_iso8859_1 nls_cp437 vfat fat intel_rapl skx_edac x86_pkg_temp_thermal coretemp iTCO_wdt iTCO_vendor_support crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel ses raid0 aesni_intel cdc_ether enclosure usbnet ipmi_ssif joydev aes_x86_64 i40e scsi_transport_sas mii bcache md_mod crypto_simd mei_me ioatdma crc64 ptp cryptd pcspkr i2c_i801 mlx4_core glue_helper pps_core mei lpc_ich dca wmi ipmi_si ipmi_devintf nd_pmem dax_pmem nd_btt ipmi_msghandler device_dax pcc_cpufreq button hid_generic usbhid mgag200 i2c_algo_bit drm_kms_helper syscopyarea sysfillrect xhci_pci sysimgblt fb_sys_fops xhci_hcd
  ttm megaraid_sas drm usbcore nfit libnvdimm sg dm_multipath dm_mod scsi_dh_rdac scsi_dh_emc scsi_dh_alua efivarfs
[  564.299390] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  564.348360] CR2: 000000000000001c
[  564.348362] ---[ end trace b7f0e5cc7b2103b0 ]---

Therefore, it is not enough to only check whether c->gc_thread is NULL, we should use IS_ERR_OR_NULL() to check both NULL pointer and error value.

This patch changes the above buggy code piece in this way,

         if (!IS_ERR_OR_NULL(c->gc_thread))
                 kthread_stop(c->gc_thread);
---
 drivers/md/bcache/super.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/md/bcache/super.c +1 -1
index 02757b90e402..e42092146083 100644
@@ -1403,7 +1403,7 @@ static void cache_set_flush(struct closure *cl)
 	kobject_put(&c->internal);
 	kobject_del(&c->kobj);
 
-	if (c->gc_thread)
+	if (!IS_ERR_OR_NULL(c->gc_thread))
 		kthread_stop(c->gc_thread);
 
 	if (!IS_ERR_OR_NULL(c->root))
Signature · 1 line
2.20.1
author maintainer
#49 lore raw

PATCH 50/53 Bluetooth: hci_bcsp: Fix memory leak in rx_skb

In reply to Sasha Levin

From: Tomas Bortoli <[email protected]>

[ Upstream commit 4ce9146e0370fcd573f0372d9b4e5a211112567c ]

Syzkaller found that it is possible to provoke a memory leak by never freeing rx_skb in struct bcsp_struct.

Fix by freeing in bcsp_close()

---
 drivers/bluetooth/hci_bcsp.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/bluetooth/hci_bcsp.c +5 -0
index d0b615a932d1..9833b53a8b50 100644
@@ -729,6 +729,11 @@ static int bcsp_close(struct hci_uart *hu)
 	skb_queue_purge(&bcsp->rel);
 	skb_queue_purge(&bcsp->unrel);
 
+	if (bcsp->rx_skb) {
+		kfree_skb(bcsp->rx_skb);
+		bcsp->rx_skb = NULL;
+	}
+
 	kfree(bcsp);
 	return 0;
 }
Signature · 1 line
2.20.1
author maintainer
#50 lore raw

PATCH 51/53 Bluetooth: 6lowpan: search for destination address in all peers

In reply to Sasha Levin

From: Josua Mayer <[email protected]>

[ Upstream commit b188b03270b7f8568fc714101ce82fbf5e811c5a ]

Handle overlooked case where the target address is assigned to a peer and neither route nor gateway exist.

For one peer, no checks are performed to see if it is meant to receive packets for a given address.

As soon as there is a second peer however, checks are performed to deal with routes and gateways for handling complex setups with multiple hops to a target address.
This logic assumed that no route and no gateway imply that the destination address can not be reached, which is false in case of a direct peer.

---
 net/bluetooth/6lowpan.c | 14 ++++++++++----
 1 file changed, 10 insertions(+), 4 deletions(-)
net/bluetooth/6lowpan.c +10 -4
index 795ddd8b2f77..4cd6b8d811ff 100644
@@ -184,10 +184,16 @@ static inline struct lowpan_peer *peer_lookup_dst(struct lowpan_dev *dev,
 	}
 
 	if (!rt) {
-		nexthop = &lowpan_cb(skb)->gw;
-
-		if (ipv6_addr_any(nexthop))
-			return NULL;
+		if (ipv6_addr_any(&lowpan_cb(skb)->gw)) {
+			/* There is neither route nor gateway,
+			 * probably the destination is a direct peer.
+			 */
+			nexthop = daddr;
+		} else {
+			/* There is a known gateway
+			 */
+			nexthop = &lowpan_cb(skb)->gw;
+		}
 	} else {
 		nexthop = rt6_nexthop(rt, daddr);
 
Signature · 1 line
2.20.1
author maintainer
#51 lore raw

PATCH 52/53 Bluetooth: Check state in l2cap_disconnect_rsp

In reply to Sasha Levin

From: Matias Karhumaa <[email protected]>

[ Upstream commit 28261da8a26f4915aa257d12d506c6ba179d961f ]

Because of both sides doing L2CAP disconnection at the same time, it was possible to receive L2CAP Disconnection Response with CID that was already freed. That caused problems if CID was already reused and L2CAP Connection Request with same CID was sent out. Before this patch kernel deleted channel context regardless of the state of the channel.

Example where leftover Disconnection Response (frame #402) causes local device to delete L2CAP channel which was not yet connected. This in turn confuses remote device's stack because same CID is re-used without properly disconnecting.

Btmon capture before patch:
** snip **

Quoted 1 line

ACL Data RX: Handle 43 flags 0x02 dlen 8 #394 [hci1] 10.748949

      Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
      RFCOMM: Disconnect (DISC) (0x43)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x53 poll/final 1
         Length: 0
         FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8                #395 [hci1] 10.749062
      Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
      RFCOMM: Unnumbered Ack (UA) (0x63)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x73 poll/final 1
         Length: 0
         FCS: 0xd7

< ACL Data TX: Handle 43 flags 0x00 dlen 12 #396 [hci1] 10.749073
L2CAP: Disconnection Request (0x06) ident 17 len 4
Destination CID: 65
Source CID: 65

Quoted 1 line

HCI Event: Number of Completed Packets (0x13) plen 5 #397 [hci1] 10.752391

Num handles: 1
Handle: 43
Count: 1

Quoted 1 line

HCI Event: Number of Completed Packets (0x13) plen 5 #398 [hci1] 10.753394

Num handles: 1
Handle: 43
Count: 1

Quoted 1 line

ACL Data RX: Handle 43 flags 0x02 dlen 12 #399 [hci1] 10.756499

L2CAP: Disconnection Request (0x06) ident 26 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #400 [hci1] 10.756548
L2CAP: Disconnection Response (0x07) ident 26 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #401 [hci1] 10.757459

      L2CAP: Connection Request (0x02) ident 18 len 4
        PSM: 1 (0x0001)
        Source CID: 65
Quoted 1 line

ACL Data RX: Handle 43 flags 0x02 dlen 12 #402 [hci1] 10.759148

L2CAP: Disconnection Response (0x07) ident 17 len 4
Destination CID: 65
Source CID: 65
= bluetoothd: 00:1E:AB:4C:56:54: error updating services: Input/o.. 10.759447

Quoted 1 line

HCI Event: Number of Completed Packets (0x13) plen 5 #403 [hci1] 10.759386

Num handles: 1
Handle: 43
Count: 1

Quoted 1 line

ACL Data RX: Handle 43 flags 0x02 dlen 12 #404 [hci1] 10.760397

      L2CAP: Connection Request (0x02) ident 27 len 4
        PSM: 3 (0x0003)
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16               #405 [hci1] 10.760441
      L2CAP: Connection Response (0x03) ident 27 len 8
        Destination CID: 65
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)

< ACL Data TX: Handle 43 flags 0x00 dlen 27 #406 [hci1] 10.760449
L2CAP: Configure Request (0x04) ident 19 len 19
Destination CID: 65
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 1013
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Basic (0x00)
TX window size: 0
Max transmit: 0
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 0

Quoted 1 line

HCI Event: Number of Completed Packets (0x13) plen 5 #407 [hci1] 10.761399

Num handles: 1
Handle: 43
Count: 1

Quoted 1 line

ACL Data RX: Handle 43 flags 0x02 dlen 16 #408 [hci1] 10.762942

      L2CAP: Connection Response (0x03) ident 18 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)

*snip*

Similar case after the patch:
*snip*

Quoted 1 line

ACL Data RX: Handle 43 flags 0x02 dlen 8 #22702 [hci0] 1664.411056

      Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
      RFCOMM: Disconnect (DISC) (0x43)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x53 poll/final 1
         Length: 0
         FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8            #22703 [hci0] 1664.411136
      Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
      RFCOMM: Unnumbered Ack (UA) (0x63)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x73 poll/final 1
         Length: 0
         FCS: 0xd7

< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22704 [hci0] 1664.411143
L2CAP: Disconnection Request (0x06) ident 11 len 4
Destination CID: 65
Source CID: 65

Quoted 1 line

HCI Event: Number of Completed Pac.. (0x13) plen 5 #22705 [hci0] 1664.414009

Num handles: 1
Handle: 43
Count: 1

Quoted 1 line

HCI Event: Number of Completed Pac.. (0x13) plen 5 #22706 [hci0] 1664.415007

Num handles: 1
Handle: 43
Count: 1

Quoted 1 line

ACL Data RX: Handle 43 flags 0x02 dlen 12 #22707 [hci0] 1664.418674

L2CAP: Disconnection Request (0x06) ident 17 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22708 [hci0] 1664.418762
L2CAP: Disconnection Response (0x07) ident 17 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22709 [hci0] 1664.421073

      L2CAP: Connection Request (0x02) ident 12 len 4
        PSM: 1 (0x0001)
        Source CID: 65
Quoted 1 line

ACL Data RX: Handle 43 flags 0x02 dlen 12 #22710 [hci0] 1664.421371

L2CAP: Disconnection Response (0x07) ident 11 len 4
Destination CID: 65
Source CID: 65

Quoted 1 line

HCI Event: Number of Completed Pac.. (0x13) plen 5 #22711 [hci0] 1664.424082

Num handles: 1
Handle: 43
Count: 1

Quoted 1 line

HCI Event: Number of Completed Pac.. (0x13) plen 5 #22712 [hci0] 1664.425040

Num handles: 1
Handle: 43
Count: 1

Quoted 1 line

ACL Data RX: Handle 43 flags 0x02 dlen 12 #22713 [hci0] 1664.426103

      L2CAP: Connection Request (0x02) ident 18 len 4
        PSM: 3 (0x0003)
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16           #22714 [hci0] 1664.426186
      L2CAP: Connection Response (0x03) ident 18 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)

< ACL Data TX: Handle 43 flags 0x00 dlen 27 #22715 [hci0] 1664.426196
L2CAP: Configure Request (0x04) ident 13 len 19
Destination CID: 65
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 1013
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Basic (0x00)
TX window size: 0
Max transmit: 0
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 0

Quoted 1 line

ACL Data RX: Handle 43 flags 0x02 dlen 16 #22716 [hci0] 1664.428804

      L2CAP: Connection Response (0x03) ident 12 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)

*snip*

Fix is to check that channel is in state BT_DISCONN before deleting the channel.

This bug was found while fuzzing Bluez's OBEX implementation using Synopsys Defensics.

---
 net/bluetooth/l2cap_core.c | 6 ++++++
 1 file changed, 6 insertions(+)
net/bluetooth/l2cap_core.c +6 -0
index 46afd560f242..c25f1e4846cd 100644
@@ -4363,6 +4363,12 @@ static inline int l2cap_disconnect_rsp(struct l2cap_conn *conn,
 
 	l2cap_chan_lock(chan);
 
+	if (chan->state != BT_DISCONN) {
+		l2cap_chan_unlock(chan);
+		mutex_unlock(&conn->chan_lock);
+		return 0;
+	}
+
 	l2cap_chan_hold(chan);
 	l2cap_chan_del(chan, 0);
 
Signature · 1 line
2.20.1
author maintainer
#52 lore raw

PATCH 53/53 Bluetooth: validate BLE connection interval updates

In reply to Sasha Levin

From: csonsino <[email protected]>

[ Upstream commit c49a8682fc5d298d44e8d911f4fa14690ea9485e ]

Problem: The Linux Bluetooth stack yields complete control over the BLE connection interval to the remote device.

The Linux Bluetooth stack provides access to the BLE connection interval min and max values through /sys/kernel/debug/bluetooth/hci0/ conn_min_interval and /sys/kernel/debug/bluetooth/hci0/conn_max_interval. These values are used for initial BLE connections, but the remote device has the ability to request a connection parameter update. In the event that the remote side requests to change the connection interval, the Linux kernel currently only validates that the desired value is within the acceptable range in the Bluetooth specification (6 - 3200, corresponding to 7.5ms - 4000ms). There is currently no validation that the desired value requested by the remote device is within the min/max limits specified in the conn_min_interval/conn_max_interval configurations. This essentially leads to Linux yielding complete control over the connection interval to the remote device.

The proposed patch adds a verification step to the connection parameter update mechanism, ensuring that the desired value is within the min/max bounds of the current connection. If the desired value is outside of the current connection min/max values, then the connection parameter update request is rejected and the negative response is returned to the remote device. Recall that the initial connection is established using the local conn_min_interval/conn_max_interval values, so this allows the Linux administrator to retain control over the BLE connection interval.

The one downside that I see is that the current default Linux values for conn_min_interval and conn_max_interval typically correspond to 30ms and 50ms respectively. If this change were accepted, then it is feasible that some devices would no longer be able to negotiate to their desired connection interval values. This might be remedied by setting the default Linux conn_min_interval and conn_max_interval values to the widest supported range (6 - 3200 / 7.5ms - 4000ms). This could lead to the same behavior as the current implementation, where the remote device could request to change the connection interval value to any value that is permitted by the Bluetooth specification, and Linux would accept the desired value.

---
 net/bluetooth/hci_event.c  | 5 +++++
 net/bluetooth/l2cap_core.c | 9 ++++++++-
 2 files changed, 13 insertions(+), 1 deletion(-)
net/bluetooth/hci_event.c +5 -0
index 37fe2b158c2a..c4e94f34d048 100644
@@ -5062,6 +5062,11 @@ static void hci_le_remote_conn_param_req_evt(struct hci_dev *hdev,
 		return send_conn_param_neg_reply(hdev, handle,
 						 HCI_ERROR_UNKNOWN_CONN_ID);
 
+	if (min < hcon->le_conn_min_interval ||
+	    max > hcon->le_conn_max_interval)
+		return send_conn_param_neg_reply(hdev, handle,
+						 HCI_ERROR_INVALID_LL_PARAMS);
+
 	if (hci_check_conn_params(min, max, latency, timeout))
 		return send_conn_param_neg_reply(hdev, handle,
 						 HCI_ERROR_INVALID_LL_PARAMS);
net/bluetooth/l2cap_core.c +8 -1
index c25f1e4846cd..8cfba78d26f6 100644
@@ -5266,7 +5266,14 @@ static inline int l2cap_conn_param_update_req(struct l2cap_conn *conn,
 
 	memset(&rsp, 0, sizeof(rsp));
 
-	err = hci_check_conn_params(min, max, latency, to_multiplier);
+	if (min < hcon->le_conn_min_interval ||
+	    max > hcon->le_conn_max_interval) {
+		BT_DBG("requested connection interval exceeds current bounds.");
+		err = -EINVAL;
+	} else {
+		err = hci_check_conn_params(min, max, latency, to_multiplier);
+	}
+
 	if (err)
 		rsp.result = cpu_to_le16(L2CAP_CONN_PARAM_REJECTED);
 	else
Signature · 1 line
2.20.1