Add LED/WDT support
Subsystems (2)
cover Add LED/WDT support
This patch series add LED/Watchdog support for EK874 platform. It also enabled DMA for SCIF2 and fixes SCIF5 DMA channels.
This patch series is based on linux-4.19.y-cip and all the patches in this series are cherry-picked from linux rc tree.
This patch series is depend on the below patch series
https://patchwork.kernel.org/project/cip-dev/list/?series=145943
Biju Das (1):
arm64: dts: renesas: r8a774c0: sort subnodes of the soc node
Fabrizio Castro (2):
arm64: dts: renesas: r8a774c0-cat874: Add LEDs support
arm64: dts: renesas: r8a774c0-cat874: Add RWDT support
Geert Uytterhoeven (2):
arm64: dts: renesas: r8a774c0: Enable DMA for SCIF2
arm64: dts: renesas: r8a774c0: Fix SCIF5 DMA channels
Niklas S?derlund (1):
arm64: dts: renesas: r8a774c0: Remove invalid compatible value for
CSI40
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts | 29 +++ arch/arm64/boot/dts/renesas/r8a774c0.dtsi | 261 ++++++++++++------------ 2 files changed, 160 insertions(+), 130 deletions(-)
Signature · 1 line
2.7.4
PATCH 1/6 arm64: dts: renesas: r8a774c0-cat874: Add LEDs support
From: Fabrizio Castro <[email protected]>
commit dc0b439471323521a20314934080f51e8589fd19 upstream.
This patch adds LEDs support to the CAT874 board specific device tree.
--- arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+)
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts +24 -0
@@ -22,6 +22,30 @@ stdout-path = "serial0:115200n8"; }; + leds { + compatible = "gpio-leds"; + + led0 { + gpios = <&gpio5 19 GPIO_ACTIVE_HIGH>; + label = "LED0"; + }; + + led1 { + gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; + label = "LED1"; + }; + + led2 { + gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; + label = "LED2"; + }; + + led3 { + gpios = <&gpio6 4 GPIO_ACTIVE_HIGH>; + label = "LED3"; + }; + }; + memory at 48000000 { device_type = "memory"; /* first 128MB is reserved for secure area. */
Signature · 1 line
2.7.4
PATCH 1/6 arm64: dts: renesas: r8a774c0-cat874: Add LEDs support
Hi!
Quoted 20 lines
index f08778e..af396bb 100644
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts +13
-0@@ -22,6 +22,30 @@ stdout-path = "serial0:115200n8"; }; + leds { + compatible = "gpio-leds"; + + led0 { + gpios = <&gpio5 19 GPIO_ACTIVE_HIGH>; + label = "LED0"; + }; + + led1 { + gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; + label = "LED1"; + }; +
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts line 47
Quoted 10 lines
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts +10
-0+ led2 { + gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; + label = "LED2"; + }; + + led3 { + gpios = <&gpio6 4 GPIO_ACTIVE_HIGH>; + label = "LED3"; + }; + };
With my LED maintainer hat on... these are not exactly useful LED names. Do they have any fixed meaning? Are they labeled on the board? What color are they?
Best regards,
Pavel
Signature · 9 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 181 bytes Desc: Digital signature URL: <http://lists.cip-project.org/pipermail/cip-dev/attachments/20190716/6f76ff3f/attachment.sig>
PATCH 1/6 arm64: dts: renesas: r8a774c0-cat874: Add LEDs support
Hi Pavel,
Thanks for the feedback.
Quoted 31 lines
Subject: Re: [cip-dev] [PATCH 4.19.y-cip 1/6] arm64: dts: renesas: r8a774c0-
cat874: Add LEDs supportHi!
Quoted 26 lines
index f08778e..af396bb 100644
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts +19
-0@@ -22,6 +22,30 @@ stdout-path = "serial0:115200n8"; }; + leds { + compatible = "gpio-leds"; + + led0 { + gpios = <&gpio5 19 GPIO_ACTIVE_HIGH>; + label = "LED0"; + }; + + led1 { + gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; + label = "LED1"; + }; + + led2 { + gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; + label = "LED2"; + }; + + led3 {
Quoted 8 lines
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts line 47
Quoted 4 lines
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts +4
-0+ gpios = <&gpio6 4 GPIO_ACTIVE_HIGH>; + label = "LED3"; + }; + };With my LED maintainer hat on... these are not exactly useful LED names. Do they have any fixed meaning? Are they labeled on the board? What color are they?
It is labelled as LED0 label on the board and green colour.
Basically this board is as per 96boards CE specification System and User LEDs
The following LEDs shall be present on the board. The LEDs shall be of the specified size, color and location. The User LEDs shall be directly programmable from the SoC.
1. WiFi activity LED Yellow Type: 0603 SMD
2. Bluetooth activity LED Blue Type: 0603 SMD
3. User LEDs x4 Green Type: 0603 SMD
Other LEDs and UI interfaces are optional.
As a LED maintainer, What is your recommendation for mainline?
1) label = "LED0"; --> based on the label on the board
2) label = " gren:LED0 "; --> based on the colour and label on the board.
3) label = " green:user1";--> based on the colour and label as per 96 boards CE specification.
Regards,
Biju
PATCH 1/6 arm64: dts: renesas: r8a774c0-cat874: Add LEDs support
Hi!
Quoted 22 lines
Quoted 9 lines
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts line 47
Quoted 5 lines
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts +5
-0+ led3 { + gpios = <&gpio6 4 GPIO_ACTIVE_HIGH>; + label = "LED3"; + }; + };With my LED maintainer hat on... these are not exactly useful LED names. Do they have any fixed meaning? Are they labeled on the board? What color are they?
It is labelled as LED0 label on the board and green colour.
Basically this board is as per 96boards CE specification System and User LEDs
The following LEDs shall be present on the board. The LEDs shall be of the specified size, color and location. The User LEDs shall be directly programmable from the SoC.
1. WiFi activity LED Yellow Type: 0603 SMD
2. Bluetooth activity LED Blue Type: 0603 SMD
3. User LEDs x4 Green Type: 0603 SMD
Other LEDs and UI interfaces are optional.
Quoted 7 lines
As a LED maintainer, What is your recommendation for mainline?
1) label = "LED0"; --> based on the label on the board
2) label = " gren:LED0 "; --> based on the colour and label on the board.
3) label = " green:user1";--> based on the colour and label as per 96 boards CE specification.
Lets make it "green:user1".
Thank you,
Pavel
Signature · 9 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 181 bytes Desc: Digital signature URL: <http://lists.cip-project.org/pipermail/cip-dev/attachments/20190717/cdaad348/attachment-0001.sig>
PATCH 2/6 arm64: dts: renesas: r8a774c0-cat874: Add RWDT support
In reply to Biju DasFrom: Fabrizio Castro <[email protected]>
commit 79223ca1f57776d2770da9561c26cc2f2dd42205 upstream.
Enable RWDT and use 60 seconds as default timeout.
--- arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts | 5 +++++ 1 file changed, 5 insertions(+)
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts +5 -0
@@ -137,6 +137,11 @@ }; }; +&rwdt { + timeout-sec = <60>; + status = "okay"; +}; + &scif2 { pinctrl-0 = <&scif2_pins>; pinctrl-names = "default";
Signature · 1 line
2.7.4
PATCH 2/6 arm64: dts: renesas: r8a774c0-cat874: Add RWDT support
Quoted 5 lines · Biju Das
From: Fabrizio Castro <[email protected]>
commit
79223ca1f57776d2770da9561c26cc2f2dd42205upstream.Enable RWDT and use 60 seconds as default timeout.
So this will reboot machine if userspace does not ping it within 60 seconds by default?
Will that break user configurations that worked up till now, but do not contain watchdog support?
Do we care?
Thanks,
Pavel
Quoted 12 lines
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts +5
-0@@ -137,6 +137,11 @@ }; }; +&rwdt { + timeout-sec = <60>; + status = "okay"; +}; + &scif2 { pinctrl-0 = <&scif2_pins>; pinctrl-names = "default";
Signature · 9 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 181 bytes Desc: Digital signature URL: <http://lists.cip-project.org/pipermail/cip-dev/attachments/20190716/ee60b189/attachment-0001.sig>
PATCH 2/6 arm64: dts: renesas: r8a774c0-cat874: Add RWDT support
Hi Pavel,
Thanks for the feedback.
Quoted 4 lines
Subject: Re: [cip-dev] [PATCH 4.19.y-cip 2/6] arm64: dts: renesas: r8a774c0-
cat874: Add RWDT supportOn Mon 2019-07-15 15:28:46, Biju Das wrote:
Quoted 8 lines
Quoted 5 lines
From: Fabrizio Castro <[email protected]>
commit
79223ca1f57776d2770da9561c26cc2f2dd42205upstream.Enable RWDT and use 60 seconds as default timeout.
So this will reboot machine if userspace does not ping it within 60 seconds by default?
Yes, if you enable watchdog in user space and there is no ping activity for 60 sec. We can verify this by using the below command
cat > /dev/watchdog0 & for i in $(seq 100); do echo $i; sleep 1; done
Quoted 5 lines
Will that break user configurations that worked up till now, but do not contain watchdog support?
Do we care?
As per [1]
- timeout-sec : Contains the watchdog timeout in seconds
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt?h=v5.2
If time-out is not specified, then it uses the default timeout mentioned by the driver.
Regards,
Biju
Quoted 17 lines
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts line 147
Quoted 13 lines
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts +5
-0@@ -137,6 +137,11 @@ }; }; +&rwdt { + timeout-sec = <60>; + status = "okay"; +}; + &scif2 { pinctrl-0 = <&scif2_pins>; pinctrl-names = "default";--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
PATCH 2/6 arm64: dts: renesas: r8a774c0-cat874: Add RWDT support
Hi!
Quoted 7 lines
Quoted 7 lines
cat874: Add RWDT support
Quoted 4 lines · Biju Das
From: Fabrizio Castro <[email protected]>
commit
79223ca1f57776d2770da9561c26cc2f2dd42205upstream.
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
Enable RWDT and use 60 seconds as default timeout.
So this will reboot machine if userspace does not ping it within 60 seconds by default?
Yes, if you enable watchdog in user space and there is no ping activity for 60 sec. We can verify this by using the below command
Aha. But if userspace does nothing, no reboot happens. Good.
Best regards,
Pavel
Signature · 9 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 181 bytes Desc: Digital signature URL: <http://lists.cip-project.org/pipermail/cip-dev/attachments/20190717/54762e4a/attachment.sig>
PATCH 3/6 arm64: dts: renesas: r8a774c0: Enable DMA for SCIF2
In reply to Biju DasFrom: Geert Uytterhoeven <[email protected]>
commit d9fd4e5814079ba4a2111d7d792a24bf8f747500 upstream.
SCIF2 on RZ/G2E can be used with both DMAC1 and DMAC2.
--- arch/arm64/boot/dts/renesas/r8a774c0.dtsi | 3 +++ 1 file changed, 3 insertions(+)
arch/arm64/boot/dts/renesas/r8a774c0.dtsi +3 -0
@@ -1105,6 +1105,9 @@ <&cpg CPG_CORE R8A774C0_CLK_S3D1C>, <&scif_clk>; clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x13>, <&dmac1 0x12>, + <&dmac2 0x13>, <&dmac2 0x12>; + dma-names = "tx", "rx", "tx", "rx"; power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; resets = <&cpg 310>; status = "disabled";
Signature · 1 line
2.7.4
PATCH 4/6 arm64: dts: renesas: r8a774c0: Fix SCIF5 DMA channels
In reply to Biju DasFrom: Geert Uytterhoeven <[email protected]>
commit c21cd4ae82e169b394139243684aaacf31bfcdf8 upstream.
Correct the DMA channels for SCIF5 from 16..47 to 0..15, as was done for R-Car E3.
--- arch/arm64/boot/dts/renesas/r8a774c0.dtsi | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-)
arch/arm64/boot/dts/renesas/r8a774c0.dtsi +3 -4
@@ -2,7 +2,7 @@ /* * Device Tree Source for the RZ/G2E (R8A774C0) SoC * - * Copyright (C) 2018 Renesas Electronics Corp. + * Copyright (C) 2018-2019 Renesas Electronics Corp. */ #include <dt-bindings/clock/r8a774c0-cpg-mssr.h>
@@ -1154,9 +1154,8 @@ <&cpg CPG_CORE R8A774C0_CLK_S3D1C>, <&scif_clk>; clock-names = "fck", "brg_int", "scif_clk"; - dmas = <&dmac1 0x5b>, <&dmac1 0x5a>, - <&dmac2 0x5b>, <&dmac2 0x5a>; - dma-names = "tx", "rx", "tx", "rx"; + dmas = <&dmac0 0x5b>, <&dmac0 0x5a>; + dma-names = "tx", "rx"; power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; resets = <&cpg 202>; status = "disabled";
Signature · 1 line
2.7.4
PATCH 5/6 arm64: dts: renesas: r8a774c0: Remove invalid compatible value for CSI40
In reply to Biju DasFrom: Niklas S?derlund <[email protected]>
commit 82ec009297bc573e6aace629181d13ed6ce3772f upstream.
The compatible value renesas,rcar-gen3-csi2 was used while prototyping the R-Car CSI-2 driver but was removed before the driver was merged.
--- arch/arm64/boot/dts/renesas/r8a774c0.dtsi | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)
arch/arm64/boot/dts/renesas/r8a774c0.dtsi +1 -2
@@ -1668,8 +1668,7 @@ }; csi40: csi2 at feaa0000 { - compatible = "renesas,r8a774c0-csi2", - "renesas,rcar-gen3-csi2"; + compatible = "renesas,r8a774c0-csi2"; reg = <0 0xfeaa0000 0 0x10000>; interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 716>;
Signature · 1 line
2.7.4
PATCH 6/6 arm64: dts: renesas: r8a774c0: sort subnodes of the soc node
In reply to Biju DasSort subnodes of the soc node.
- The primary key is the bus address.
- The secondary key is the IP block.
- The tertiary key is the node name.
This is part of an ongoing effort to provide consistent node order in the DT of Renesas SoCs to improve maintainability.
This should not have any run-time effect.
--- arch/arm64/boot/dts/renesas/r8a774c0.dtsi | 248 +++++++++++++++--------------- 1 file changed, 124 insertions(+), 124 deletions(-)
arch/arm64/boot/dts/renesas/r8a774c0.dtsi +124 -124
@@ -378,6 +378,71 @@ resets = <&cpg 407>; }; + tmu0: timer at e61e0000 { + compatible = "renesas,tmu-r8a774c0", "renesas,tmu"; + reg = <0 0xe61e0000 0 0x30>; + interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 125>; + clock-names = "fck"; + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; + resets = <&cpg 125>; + status = "disabled"; + }; + + tmu1: timer at e6fc0000 { + compatible = "renesas,tmu-r8a774c0", "renesas,tmu"; + reg = <0 0xe6fc0000 0 0x30>; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 124>; + clock-names = "fck"; + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; + resets = <&cpg 124>; + status = "disabled"; + }; + + tmu2: timer at e6fd0000 { + compatible = "renesas,tmu-r8a774c0", "renesas,tmu"; + reg = <0 0xe6fd0000 0 0x30>; + interrupts = <GIC_SPI 303 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 123>; + clock-names = "fck"; + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; + resets = <&cpg 123>; + status = "disabled"; + }; + + tmu3: timer at e6fe0000 { + compatible = "renesas,tmu-r8a774c0", "renesas,tmu"; + reg = <0 0xe6fe0000 0 0x30>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 122>; + clock-names = "fck"; + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; + resets = <&cpg 122>; + status = "disabled"; + }; + + tmu4: timer at ffc00000 { + compatible = "renesas,tmu-r8a774c0", "renesas,tmu"; + reg = <0 0xffc00000 0 0x30>; + interrupts = <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 121>; + clock-names = "fck"; + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; + resets = <&cpg 121>; + status = "disabled"; + }; + i2c0: i2c at e6500000 { #address-cells = <1>; #size-cells = <0>;
@@ -521,71 +586,6 @@ status = "disabled"; }; - tmu0: timer at e61e0000 { - compatible = "renesas,tmu-r8a774c0", "renesas,tmu"; - reg = <0 0xe61e0000 0 0x30>; - interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cpg CPG_MOD 125>; - clock-names = "fck"; - power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; - resets = <&cpg 125>; - status = "disabled"; - }; - - tmu1: timer at e6fc0000 { - compatible = "renesas,tmu-r8a774c0", "renesas,tmu"; - reg = <0 0xe6fc0000 0 0x30>; - interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cpg CPG_MOD 124>; - clock-names = "fck"; - power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; - resets = <&cpg 124>; - status = "disabled"; - }; - - tmu2: timer at e6fd0000 { - compatible = "renesas,tmu-r8a774c0", "renesas,tmu"; - reg = <0 0xe6fd0000 0 0x30>; - interrupts = <GIC_SPI 303 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cpg CPG_MOD 123>; - clock-names = "fck"; - power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; - resets = <&cpg 123>; - status = "disabled"; - }; - - tmu3: timer at e6fe0000 { - compatible = "renesas,tmu-r8a774c0", "renesas,tmu"; - reg = <0 0xe6fe0000 0 0x30>; - interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cpg CPG_MOD 122>; - clock-names = "fck"; - power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; - resets = <&cpg 122>; - status = "disabled"; - }; - - tmu4: timer at ffc00000 { - compatible = "renesas,tmu-r8a774c0", "renesas,tmu"; - reg = <0 0xffc00000 0 0x30>; - interrupts = <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cpg CPG_MOD 121>; - clock-names = "fck"; - power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; - resets = <&cpg 121>; - status = "disabled"; - }; - hscif0: serial at e6540000 { compatible = "renesas,hscif-r8a774c0", "renesas,rcar-gen3-hscif",
@@ -1279,65 +1279,6 @@ }; }; - xhci0: usb at ee000000 { - compatible = "renesas,xhci-r8a774c0", - "renesas,rcar-gen3-xhci"; - reg = <0 0xee000000 0 0xc00>; - interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cpg CPG_MOD 328>; - power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; - resets = <&cpg 328>; - status = "disabled"; - }; - - usb3_peri0: usb at ee020000 { - compatible = "renesas,r8a774c0-usb3-peri", - "renesas,rcar-gen3-usb3-peri"; - reg = <0 0xee020000 0 0x400>; - interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cpg CPG_MOD 328>; - power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; - resets = <&cpg 328>; - status = "disabled"; - }; - - ohci0: usb at ee080000 { - compatible = "generic-ohci"; - reg = <0 0xee080000 0 0x100>; - interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cpg CPG_MOD 703>, <&cpg CPG_MOD 704>; - phys = <&usb2_phy0>; - phy-names = "usb"; - power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; - resets = <&cpg 703>, <&cpg 704>; - status = "disabled"; - }; - - ehci0: usb at ee080100 { - compatible = "generic-ehci"; - reg = <0 0xee080100 0 0x100>; - interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cpg CPG_MOD 703>, <&cpg CPG_MOD 704>; - phys = <&usb2_phy0>; - phy-names = "usb"; - companion = <&ohci0>; - power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; - resets = <&cpg 703>, <&cpg 704>; - status = "disabled"; - }; - - usb2_phy0: usb-phy at ee080200 { - compatible = "renesas,usb2-phy-r8a774c0", - "renesas,rcar-gen3-usb2-phy"; - reg = <0 0xee080200 0 0x700>; - interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cpg CPG_MOD 703>, <&cpg CPG_MOD 704>; - power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; - resets = <&cpg 703>, <&cpg 704>; - #phy-cells = <0>; - status = "disabled"; - }; - rcar_sound: sound at ec500000 { /* * #sound-dai-cells is required
@@ -1587,6 +1528,65 @@ <&ipmmu_mp 14>, <&ipmmu_mp 15>; }; + xhci0: usb at ee000000 { + compatible = "renesas,xhci-r8a774c0", + "renesas,rcar-gen3-xhci"; + reg = <0 0xee000000 0 0xc00>; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 328>; + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; + resets = <&cpg 328>; + status = "disabled"; + }; + + usb3_peri0: usb at ee020000 { + compatible = "renesas,r8a774c0-usb3-peri", + "renesas,rcar-gen3-usb3-peri"; + reg = <0 0xee020000 0 0x400>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 328>; + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; + resets = <&cpg 328>; + status = "disabled"; + }; + + ohci0: usb at ee080000 { + compatible = "generic-ohci"; + reg = <0 0xee080000 0 0x100>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 703>, <&cpg CPG_MOD 704>; + phys = <&usb2_phy0>; + phy-names = "usb"; + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; + resets = <&cpg 703>, <&cpg 704>; + status = "disabled"; + }; + + ehci0: usb at ee080100 { + compatible = "generic-ehci"; + reg = <0 0xee080100 0 0x100>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 703>, <&cpg CPG_MOD 704>; + phys = <&usb2_phy0>; + phy-names = "usb"; + companion = <&ohci0>; + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; + resets = <&cpg 703>, <&cpg 704>; + status = "disabled"; + }; + + usb2_phy0: usb-phy at ee080200 { + compatible = "renesas,usb2-phy-r8a774c0", + "renesas,rcar-gen3-usb2-phy"; + reg = <0 0xee080200 0 0x700>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 703>, <&cpg CPG_MOD 704>; + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; + resets = <&cpg 703>, <&cpg 704>; + #phy-cells = <0>; + status = "disabled"; + }; + sdhi0: sd at ee100000 { compatible = "renesas,sdhi-r8a774c0", "renesas,rcar-gen3-sdhi";
Signature · 1 line
2.7.4
Pavel Machek
Appliedcover Add LED/WDT support
In reply to Biju DasHi!
Quoted 5 lines
This patch series add LED/Watchdog support for EK874 platform. It also enabled DMA for SCIF2 and fixes SCIF5 DMA channels.
This patch series is based on linux-4.19.y-cip and all the patches in this series are cherry-picked from linux rc tree.
Thanks, applied and pushed out.
Pavel
Signature · 9 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 181 bytes Desc: Digital signature URL: <http://lists.cip-project.org/pipermail/cip-dev/attachments/20190717/771f356e/attachment.sig>