imx: i.MX7ULP: add get_boot_device
PATCH RESEND 1/14 imx: i.MX7ULP: add get_boot_device
Add get_boot_device for i.MX7ULP
--- arch/arm/include/asm/arch-mx7ulp/imx-regs.h | 13 +++++++++++++ arch/arm/include/asm/arch-mx7ulp/sys_proto.h | 1 + arch/arm/mach-imx/mx7ulp/soc.c | 27 +++++++++++++++++++++++++++ 3 files changed, 41 insertions(+)
arch/arm/include/asm/arch-mx7ulp/imx-regs.h +13 -0
@@ -10,6 +10,8 @@#define ARCH_MXC +#define ROM_SW_INFO_ADDR 0x000001E8 +#define CAAM_SEC_SRAM_BASE (0x26000000)#define CAAM_SEC_SRAM_SIZE (SZ_32K)#define CAAM_SEC_SRAM_END (CAAM_SEC_SRAM_BASE + CAAM_SEC_SRAM_SIZE - 1)
@@ -1112,6 +1114,17 @@ struct usbphy_regs {u32 usb1_pfda_ctrl1_tog;/* 0x14c */ }; +struct bootrom_sw_info { +u8 reserved_1; +u8 boot_dev_instance; +u8 boot_dev_type; +u8 reserved_2; +u32 core_freq; +u32 axi_freq; +u32 ddr_freq; +u32 rom_tick_freq; +u32 reserved_3[3 ]; +};#define is_boot_from_usb (void) (!(readl(USB_PHY0_BASE_ADDR) & (1<<20)))#define disconnect_from_pc (void) writel(0x0, USBOTG0_RBASE + 0x140)
arch/arm/include/asm/arch-mx7ulp/sys_proto.h +1 -0
@@ -17,4 +17,5 @@ enum bt_mode {SINGLE_BOOT /* LP_BT = 0, DUAL_BT = 0 */ }; +enum boot_device get_boot_device (void );#endif
arch/arm/mach-imx/mx7ulp/soc.c +27 -0
@@ -6,6 +6,7 @@#include <asm/arch/clock.h> #include <asm/arch/imx-regs.h> #include <asm/arch/sys_proto.h> +#include <asm/mach-imx/boot_mode.h> #include <asm/mach-imx/hab.h> static char *get_reset_cause (char *);
@@ -244,3 +245,29 @@ int mmc_get_env_dev(void) return board_mmc_get_env_dev(devno); }#endif + +enum boot_device get_boot_device (void ) +{ +struct bootrom_sw_info **p = + (struct bootrom_sw_info **)ROM_SW_INFO_ADDR ; + +enum boot_device boot_dev =SD1_BOOT ; +u8 boot_type = (*p)->boot_dev_type; +u8 boot_instance = (*p)->boot_dev_instance; + +switch (boot_type) { +case BOOT_TYPE_SD : + boot_dev = boot_instance +SD1_BOOT ; +break ; +case BOOT_TYPE_MMC : + boot_dev = boot_instance +MMC1_BOOT ; +break ; +case BOOT_TYPE_USB : + boot_dev =USB_BOOT ; +break ; +default : +break ; + } + +return boot_dev; +}
Signature · 1 line
2.16.4
PATCH RESEND 2/14 i.MX7ULP: evk: Modify FDT file to disable SD3.0 for usb boot
Since the SD3.0 kernel driver needs M4 image support, this causes problem for usb boot booting into kernel. To decouple the relationship, we modify the FDT file in u-boot to disable SD3.0.
So the kernel won't depend on M4 image.
--- board/freescale/mx7ulp_evk/mx7ulp_evk.c | 47 +++++++++++++++++++++++++++++++++ configs/mx7ulp_evk_defconfig | 1 + 2 files changed, 48 insertions(+)
board/freescale/mx7ulp_evk/mx7ulp_evk.c +47 -0
@@ -4,10 +4,12 @@*/ #include <common.h> +#include <fdt_support.h> #include <asm/io.h> #include <asm/arch/sys_proto.h> #include <asm/arch/mx7ulp-pins.h> #include <asm/arch/iomux.h> +#include <asm/mach-imx/boot_mode.h> DECLARE_GLOBAL_DATA_PTR ;
@@ -45,3 +47,48 @@ int board_init(void)return 0 ; } + +#if IS_ENABLED (CONFIG_OF_BOARD_SETUP ) +int ft_board_setup (void *blob,bd_t *bd) +{ +const char *path; +int rc, nodeoff; + +if (get_boot_device () ==USB_BOOT ) { + path =fdt_get_alias (blob,"mmc0" ); +if (!path) { +puts ("Not found mmc0\n" ); +return 0 ; + } + + nodeoff =fdt_path_offset (blob, path); +if (nodeoff <0 ) +return 0 ; + +printf ("Found usdhc0 node\n" ); +if (fdt_get_property (blob, nodeoff,"vqmmc-supply" , +NULL ) !=NULL ) { + rc =fdt_delprop (blob, nodeoff,"vqmmc-supply" ); +if (!rc) { +puts ("Removed vqmmc-supply property\n" ); +add: + rc =fdt_setprop (blob, nodeoff, +"no-1-8-v" ,NULL ,0 ); +if (rc == -FDT_ERR_NOSPACE ) { + rc =fdt_increase_size (blob,32 ); +if (!rc) + goto add; + }else if (rc) { +printf ("Failed to add no-1-8-v property, %d\n" , rc); + }else { +puts ("Added no-1-8-v property\n" ); + } + }else { +printf ("Failed to remove vqmmc-supply property, %d\n" , rc); + } + } + } + +return 0 ; +} +#endif
configs/mx7ulp_evk_defconfig +1 -0
@@ -3,6 +3,7 @@ CONFIG_ARCH_MX7ULP=y CONFIG_SYS_TEXT_BASE=0x67800000 CONFIG_TARGET_MX7ULP_EVK=y CONFIG_NR_DRAM_BANKS=1 +CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7ulp_evk/imximage.cfg" CONFIG_BOUNCE_BUFFER=y CONFIG_HUSH_PARSER=y
Signature · 1 line
2.16.4
PATCH RESEND 3/14 i.MX7ULP: Fix system reset after a7 rtc alarm expired.
In reply to Peng FanFrom: Bai Ping <[email protected]>
The board will reboot if A7 core enter mem mode by rtc, then M4 core enter VLLS mode after the RTC alarm expired. Enable the dumb PMIC mode to fix this issue.
Since i.MX7ULP B0 moves the SNVS LP into M4 domain, A core can't access it. So check the CPU rev and not apply the settings for B0.
--- arch/arm/include/asm/arch-mx7ulp/imx-regs.h | 7 +++++++ arch/arm/mach-imx/mx7ulp/soc.c | 4 ++++ 2 files changed, 11 insertions(+)
arch/arm/include/asm/arch-mx7ulp/imx-regs.h +7 -0
@@ -58,6 +58,7 @@#define USDHC1_AIPS2_SLOT (56)#define RGPIO2P0_AIPS0_SLOT (15)#define RGPIO2P1_AIPS2_SLOT (15) +#define SNVS_AIPS2_SLOT (35)#define IOMUXC0_AIPS0_SLOT (61)#define OCOTP_CTRL_AIPS1_SLOT (38)#define OCOTP_CTRL_PCC1_SLOT (38)
@@ -177,6 +178,9 @@#define USDHC0_RBASE ((AIPS2_BASE + (AIPS2_SLOT_SIZE * USDHC0_AIPS2_SLOT)))#define USDHC1_RBASE ((AIPS2_BASE + (AIPS2_SLOT_SIZE * USDHC1_AIPS2_SLOT))) +#define SNVS_BASE ((AIPS2_BASE + (AIPS2_SLOT_SIZE * SNVS_AIPS2_SLOT))) +#define SNVS_LP_LPCR (SNVS_BASE + 0x38) +#define RGPIO2P0_RBASE ((AIPS0_BASE + (AIPS0_SLOT_SIZE * RGPIO2P0_AIPS0_SLOT)))#define RGPIO2P1_RBASE ((AIPS2_BASE + (AIPS2_SLOT_SIZE * RGPIO2P1_AIPS2_SLOT)))
@@ -939,6 +943,9 @@#define MMDC_MPWRDQBY3DL_WR_DQ25_DEL_MASK ((0x3f << MMDC_MPWRDQBY3DL_WR_DQ25_DEL))#define MMDC_MPWRDQBY3DL_WR_DQ24_DEL_MASK ((0x3f << MMDC_MPWRDQBY3DL_WR_DQ24_DEL)) +#define SNVS_LPCR_DPEN (0x20) +#define SNVS_LPCR_SRTC_ENV (0x1) +#if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__))#include <asm/types.h>
arch/arm/mach-imx/mx7ulp/soc.c +4 -0
@@ -106,6 +106,10 @@ void s_init(void)/* clock configuration. */ clock_init (); +if (soc_rev () <CHIP_REV_2_0 ) { +/* enable dumb pmic */ +writel ((readl (SNVS_LP_LPCR ) |SNVS_LPCR_DPEN ),SNVS_LP_LPCR ); + }return ; }
Signature · 1 line
2.16.4
PATCH RESEND 4/14 i.MX7ULP: Correct the clock index
In reply to Peng FanFrom: Bai Ping <[email protected]>
On i.MX7ULP, value zero is reserved in SCG1 RCCR register, so the val should be decreased by 1 to get the correct clock source index.
--- arch/arm/mach-imx/mx7ulp/scg.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-imx/mx7ulp/scg.c +1 -1
@@ -440,7 +440,7 @@ static u32 scg_sys_get_rate(enum scg_clk clk)case SCG_SCS_SLOW_IRC :case SCG_SCS_FAST_IRC :case SCG_SCS_RTC_OSC : - rate =scg_src_get_rate (scg_scs_array[val]); + rate =scg_src_get_rate (scg_scs_array[val -1 ]);break ;case 5 : rate =scg_apll_get_rate ();
Signature · 1 line
2.16.4
PATCH RESEND 5/14 i.MX7ULP: Fix PCC register bits mask and offset issue
In reply to Peng FanFrom: Ye Li <[email protected]>
The offset for FRAC and the mask for PCD are not correct. If we set FRAC, we can't get the right frequency. Fix them to correct value.
--- arch/arm/include/asm/arch-mx7ulp/pcc.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/include/asm/arch-mx7ulp/pcc.h +2 -2
@@ -289,10 +289,10 @@ enum pcc3_entry {#define PCC_INUSE_MASK (0x1 << PCC_INUSE_OFFSET)#define PCC_PCS_OFFSET 24#define PCC_PCS_MASK (0x7 << PCC_PCS_OFFSET) -#define PCC_FRAC_OFFSET 4 +#define PCC_FRAC_OFFSET 3#define PCC_FRAC_MASK (0x1 << PCC_FRAC_OFFSET)#define PCC_PCD_OFFSET 0 -#define PCC_PCD_MASK (0xf << PCC_PCD_OFFSET) +#define PCC_PCD_MASK (0x7 << PCC_PCD_OFFSET)enum pcc_clksrc_type {
Signature · 1 line
2.16.4
PATCH RESEND 6/14 i.MX7ULP: Add CONFIG_MX7ULP to kconfig
In reply to Peng FanFrom: Ye Li <[email protected]>
Since many drivers need this CONFIG_MX7ULP to distiguish the settings for i.MX7ULP only. Add this entry to cpu's kconfig.
--- arch/arm/mach-imx/mx7ulp/Kconfig | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
arch/arm/mach-imx/mx7ulp/Kconfig +5 -1
@@ -3,12 +3,16 @@ if ARCH_MX7ULP config SYS_SOC default "mx7ulp" +config MX7ULP + bool + choice prompt "MX7ULP board select" optional config TARGET_MX7ULP_EVK - bool "Support mx7ulp EVK board" + bool "Support mx7ulp EVK board" + select MX7ULP select SYS_ARCH_TIMER endchoice
Signature · 1 line
2.16.4
PATCH RESEND 7/14 i.MX7ULP: Fix wrong i2c configuration name
In reply to Peng FanFrom: Ye Li <[email protected]>
Wrong I2c driver configuration name is used in codes, so I2c driver is not built. Correct it.
--- arch/arm/include/asm/arch-mx7ulp/clock.h | 2 +- arch/arm/mach-imx/mx7ulp/clock.c | 2 +- configs/mx7ulp_evk_defconfig | 1 + configs/mx7ulp_evk_plugin_defconfig | 1 + 4 files changed, 4 insertions(+), 2 deletions(-)
arch/arm/include/asm/arch-mx7ulp/clock.h +1 -1
@@ -26,7 +26,7 @@ enum mxc_clock {u32 mxc_get_clock (enum mxc_clock clk);u32 get_lpuart_clk (void ); -#ifdef CONFIG_SYS_LPI2C_IMX +#ifdef CONFIG_SYS_I2C_IMX_LPI2C int enable_i2c_clk (unsigned char enable,unsigned i2c_num);u32 imx_get_i2cclk (unsigned i2c_num);#endif
arch/arm/mach-imx/mx7ulp/clock.c +1 -1
@@ -72,7 +72,7 @@ u32 get_lpuart_clk(void)return pcc_clock_get_rate (lpuart_pcc_clks[index -4 ]); } -#ifdef CONFIG_SYS_LPI2C_IMX +#ifdef CONFIG_SYS_I2C_IMX_LPI2C int enable_i2c_clk (unsigned char enable,unsigned i2c_num) {/* Set parent to FIRC DIV2 clock */
configs/mx7ulp_evk_defconfig +1 -0
@@ -21,6 +21,7 @@ CONFIG_DM_GPIO=y CONFIG_IMX_RGPIO2P=y # CONFIG_MXC_GPIO is not set CONFIG_DM_I2C=y +CONFIG_SYS_I2C_IMX_LPI2C=y CONFIG_DM_MMC=y CONFIG_SUPPORT_EMMC_BOOT=y CONFIG_FSL_ESDHC_IMX=y
configs/mx7ulp_evk_plugin_defconfig +1 -0
@@ -20,6 +20,7 @@ CONFIG_IMX_RGPIO2P=y # CONFIG_MXC_GPIO is not set CONFIG_DM_I2C=y CONFIG_DM_MMC=y +CONFIG_SYS_I2C_IMX_LPI2C=y CONFIG_SUPPORT_EMMC_BOOT=y CONFIG_FSL_ESDHC_IMX=y CONFIG_PINCTRL=y
Signature · 1 line
2.16.4
PATCH RESEND 8/14 misc: Kconfig: make i.MX7ULP could use MXC_OCOTP
In reply to Peng Fan--- drivers/misc/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/misc/Kconfig +1 -1
@@ -200,7 +200,7 @@ config JZ4780_EFUSE config MXC_OCOTP bool "Enable MXC OCOTP Driver" - depends on ARCH_IMX8M || ARCH_MX6 || ARCH_MX7 || ARCH_VF610 + depends on ARCH_IMX8M || ARCH_MX6 || ARCH_MX7 || ARCH_MX7ULP || ARCH_VF610 default y help If you say Y here, you will get support for the One Time
Signature · 1 line
2.16.4
PATCH RESEND 9/14 i.MX7ULP: evk: Enable fuse comamnd
In reply to Peng FanEnable fuse command
--- configs/mx7ulp_evk_defconfig | 1 + configs/mx7ulp_evk_plugin_defconfig | 1 + 2 files changed, 2 insertions(+)
configs/mx7ulp_evk_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOUNCE_BUFFER=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y CONFIG_CMD_MEMTEST=y +CONFIG_CMD_FUSE=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y
configs/mx7ulp_evk_plugin_defconfig +1 -0
@@ -7,6 +7,7 @@ CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7ulp_evk/imximage.cfg" CONFIG_BOUNCE_BUFFER=y CONFIG_HUSH_PARSER=y CONFIG_CMD_MEMTEST=y +CONFIG_CMD_FUSE=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y
Signature · 1 line
2.16.4
PATCH RESEND 10/14 i.MX7ULP: Fix SPLL/APLL clock rate calculation issue
In reply to Peng FanFrom: Ye Li <[email protected]>
The num/denom is a float value, but in the calculation it is convert to integer 0, and cause the result wrong.
--- arch/arm/mach-imx/mx7ulp/scg.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-)
arch/arm/mach-imx/mx7ulp/scg.c +8 -2
@@ -503,7 +503,10 @@ u32 decode_pll(enum pll_clocks pll) infreq = infreq / pre_div; -return infreq * mult + infreq * num / denom; +if (denom) +return infreq * mult + infreq * num / denom; +else +return infreq * mult;case PLL_A7_APLL : reg =readl (&scg1_regs->apllcsr);
@@ -532,7 +535,10 @@ u32 decode_pll(enum pll_clocks pll) infreq = infreq / pre_div; -return infreq * mult + infreq * num / denom; +if (denom) +return infreq * mult + infreq * num / denom; +else +return infreq * mult;case PLL_USB : reg =readl (&scg1_regs->upllcsr);
Signature · 1 line
2.16.4
PATCH RESEND 11/14 i.MX7ULP: Workaround APLL PFD2 to 345.6Mhz
In reply to Peng FanFrom: Ye Li <[email protected]>
The GPU uses APLL PFD2 as its clock parent (483.84Mhz) with divider set to 1. This frequecy is out of ULP A0 spec. The MAX rate for GPU is 350Mhz. So we simply configure the APLL PFD2 to 345.6Mhz (FRAC=28) to workaround the problem. The correct fix should let GPU handle the clock rate in kernel.
--- arch/arm/mach-imx/mx7ulp/clock.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/mach-imx/mx7ulp/clock.c +2 -2
@@ -300,9 +300,9 @@ void clock_init(void)scg_a7_soscdiv_init (); -/* APLL PFD1 = 270Mhz, PFD2=480Mhz, PFD3=800Mhz */ +/* APLL PFD1 = 270Mhz, PFD2=345.6Mhz, PFD3=800Mhz */ scg_enable_pll_pfd (SCG_APLL_PFD1_CLK ,35 ); -scg_enable_pll_pfd (SCG_APLL_PFD2_CLK ,20 ); +scg_enable_pll_pfd (SCG_APLL_PFD2_CLK ,28 );scg_enable_pll_pfd (SCG_APLL_PFD3_CLK ,12 );init_clk_lpuart ();
Signature · 1 line
2.16.4
PATCH RESEND 12/14 i.MX7ULP: Add CPU revision check for B0
In reply to Peng FanSince there is no register for CPU revision, we use ROM version to check the A0 or B0 chip.
--- arch/arm/mach-imx/mx7ulp/soc.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)
arch/arm/mach-imx/mx7ulp/soc.c +5 -2
@@ -18,10 +18,13 @@ struct imx_sec_config_fuse_t const imx_sec_config_fuse = { };#endif +#define ROM_VERSION_ADDR 0x80u32 get_cpu_rev (void ) { -/* Temporally hard code the CPU rev to 0x73, rev 1.0. Fix it later */ -return (MXC_CPU_MX7ULP <<12 ) | (1 <<4 ); +/* Check the ROM version for cpu revision */ +u32 rom_version =readl ((void __iomem *)ROM_VERSION_ADDR ); + +return (MXC_CPU_MX7ULP <<12 ) | (rom_version &0xFF ); }#ifdef CONFIG_REVISION_TAG
Signature · 1 line
2.16.4
PATCH RESEND 13/14 i.MX7ULP: Set A7 core frequency to 500Mhz for B0 chip
In reply to Peng FanFrom: Ye Li <[email protected]>
The normal target frequency for ULP A7 core is 500Mhz, but now ROM set the core frequency to 413Mhz. So change it to 500Mhz in u-boot.
--- arch/arm/include/asm/arch-mx7ulp/scg.h | 1 + arch/arm/mach-imx/mx7ulp/clock.c | 2 ++ arch/arm/mach-imx/mx7ulp/scg.c | 41 ++++++++++++++++++++++++++++++++++ 3 files changed, 44 insertions(+)
arch/arm/include/asm/arch-mx7ulp/scg.h +1 -0
@@ -337,5 +337,6 @@ void scg_a7_nicclk_init(void);void scg_a7_sys_clk_sel (enum scg_sys_src clk);void scg_a7_info (void );void scg_a7_soscdiv_init (void ); +void scg_a7_init_core_clk (void );#endif
arch/arm/mach-imx/mx7ulp/clock.c +2 -0
@@ -300,6 +300,8 @@ void clock_init(void)scg_a7_soscdiv_init (); +scg_a7_init_core_clk (); +/* APLL PFD1 = 270Mhz, PFD2=345.6Mhz, PFD3=800Mhz */ scg_enable_pll_pfd (SCG_APLL_PFD1_CLK ,35 );scg_enable_pll_pfd (SCG_APLL_PFD2_CLK ,28 );
arch/arm/mach-imx/mx7ulp/scg.c +41 -0
44 lines not on this page · raw message
Signature · 1 line
2.16.4
PATCH RESEND 14/14 i.MX7ULP: Change clock rate calculation for NIC1 BUS and EXT
In reply to Peng FanFrom: Ye Li <[email protected]>
On i.MX7ULP B0, there is change in NIC clock dividers architecture. On A0, the NIC1 BUS and EXT dividers were in a chain with NIC1 DIV, but on B0 they are parallel with NIC1 DIV. So now the dividers are independent. This patch modifies the scg_nic_get_rate function according to this change.
--- arch/arm/mach-imx/mx7ulp/scg.c | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-)
arch/arm/mach-imx/mx7ulp/scg.c +9 -1
@@ -352,7 +352,7 @@ static u32 scg_ddr_get_rate(void)static u32 scg_nic_get_rate (enum scg_clk clk) { -u32 reg, val, rate; +u32 reg, val, rate, nic0_rate;u32 shift, mask; reg =readl (&scg1_regs->niccsr);
@@ -370,6 +370,7 @@ static u32 scg_nic_get_rate(enum scg_clk clk) val = (reg &SCG_NICCSR_NIC0DIV_MASK ) >>SCG_NICCSR_NIC0DIV_SHIFT ; rate = rate / (val +1 ); + nic0_rate = rate;clk_debug ("scg_nic_get_rate NIC0 rate %u\n" , rate);
@@ -411,6 +412,13 @@ static u32 scg_nic_get_rate(enum scg_clk clk)return 0 ; } +/* +* On RevB, the nic_bus and nic_ext dividers are parallel +* not chained with nic div +*/ +if (soc_rev () >=CHIP_REV_2_0 ) + rate = nic0_rate; + val = (reg & mask) >> shift; rate = rate / (val +1 );
Signature · 1 line
2.16.4
Fabio Estevam
reviewerPATCH RESEND 1/14 imx: i.MX7ULP: add get_boot_device
In reply to Peng FanQuoted 4 lines · Peng Fan
Add
get_boot_devicefor i.MX7ULPSigned-off-by Peng Fan <[email protected]>
For the entire series:
Without this series I cannot boot Linux on imx7ulp-evk. With this series applied I can.
Thanks
Fabio Estevam
reviewerPATCH RESEND 1/14 imx: i.MX7ULP: add get_boot_device
Hi Stefano,
Quoted 5 lines · Fabio Estevam
Quoted 3 lines · Peng Fan
Add
get_boot_devicefor i.MX7ULP
Quoted 8 lines
Quoted 1 line
Signed-off-by Peng Fan <[email protected]>For the entire series:
Tested-by Fabio Estevam <[email protected]>Without this series I cannot boot Linux on imx7ulp-evk. With this series applied I can.
Any comments about this series, please?
I need to upstream one i.MX7ULP based board, which depends on this series.
Thanks
PATCH RESEND 1/14 imx: i.MX7ULP: add get_boot_device
Quoted 12 lines · Fabio Estevam
Hi Stefano,
Quoted 9 lines · Fabio Estevam
Quoted 4 lines · Peng Fan
Add
get_boot_devicefor i.MX7ULPSigned-off-by Peng Fan <[email protected]>For the entire series:
Quoted 8 lines
Quoted 4 lines
Tested-by Fabio Estevam <[email protected]>Without this series I cannot boot Linux on imx7ulp-evk. With this series applied I can.
Any comments about this series, please?
I need to upstream one i.MX7ULP based board, which depends on this series.
I merge it into -master today.
Thanks,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================