Skip to contentSkip to conversation

amlogic: Add support for Odroid-N2

PATCH New Neil Armstrong 2 participants 8 messages Jul 22, 2019 – Jul 23, 2019

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

cover amlogic: Add support for Odroid-N2

ODROID-N2 is a single board computer manufactured by Hardkernel Co. Ltd with the following specifications:

- Amlogic S922X ARM Cortex-A53 dual-core + Cortex-A73 quad-core SoC
- 4GB DDR4 SDRAM
- Gigabit Ethernet
- HDMI 2.1 4K/60Hz display
- 40-pin GPIO header
- 4 x USB 3.0 Host, 1 x USB OTG
- eMMC, microSD
- Infrared receiver

This patchset :
- adds the Odroid-N2 from Linux 5.3-rc1
- fixes 4GiB memory support
- adds board support

The board directory is W400, the name of the Amlogic Reference Design of Amlogic G12B with Gigabit boards, which will be used for similar boards.

Neil Armstrong (3):
ARM: dts: add support for Odroid-N2
ARM: meson-g12a: Handle 4GiB DRAM size
board: amlogic: add support for Odroid-N2

 arch/arm/dts/Makefile                         |   3 +-
 arch/arm/dts/meson-g12b-odroid-n2.dts         | 386 ++++++++++++++++++
 arch/arm/dts/meson-g12b.dtsi                  |  82 ++++
 arch/arm/mach-meson/board-g12a.c              |  13 +-
 board/amlogic/w400/MAINTAINERS                |   6 +
 board/amlogic/w400/Makefile                   |   6 +
 board/amlogic/w400/README.odroid-n2           | 130 ++++++
 board/amlogic/w400/README.w400                | 130 ++++++
 board/amlogic/w400/w400.c                     |  18 +
 configs/odroid-n2_defconfig                   |  56 +++
 .../dt-bindings/sound/meson-g12a-tohdmitx.h   |  13 +
 11 files changed, 836 insertions(+), 7 deletions(-)
 create mode 100644 arch/arm/dts/meson-g12b-odroid-n2.dts
 create mode 100644 arch/arm/dts/meson-g12b.dtsi
 create mode 100644 board/amlogic/w400/MAINTAINERS
 create mode 100644 board/amlogic/w400/Makefile
 create mode 100644 board/amlogic/w400/README.odroid-n2
 create mode 100644 board/amlogic/w400/README.w400
 create mode 100644 board/amlogic/w400/w400.c
 create mode 100644 configs/odroid-n2_defconfig
 create mode 100644 include/dt-bindings/sound/meson-g12a-tohdmitx.h
Signature · 1 line
2.22.0
#1 lore raw

PATCH 1/3 ARM: dts: add support for Odroid-N2

Import HardKernel Odroid-N2 DT from Linux 5.3-rc1, commit 5f9e832c1370 ("Linus 5.3-rc1") based on an Amlogic G12B S922X SoC.

---
 arch/arm/dts/Makefile                         |   3 +-
 arch/arm/dts/meson-g12b-odroid-n2.dts         | 386 ++++++++++++++++++
 arch/arm/dts/meson-g12b.dtsi                  |  82 ++++
 .../dt-bindings/sound/meson-g12a-tohdmitx.h   |  13 +
 4 files changed, 483 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/meson-g12b-odroid-n2.dts
 create mode 100644 arch/arm/dts/meson-g12b.dtsi
 create mode 100644 include/dt-bindings/sound/meson-g12a-tohdmitx.h
arch/arm/dts/Makefile +2 -1
index f5535078c7..2baa368215 100644
@@ -135,7 +135,8 @@ dtb-$(CONFIG_ARCH_MESON) += \
 	meson-gxl-s905x-khadas-vim.dtb \
 	meson-gxm-khadas-vim2.dtb \
 	meson-axg-s400.dtb \
-	meson-g12a-u200.dtb
+	meson-g12a-u200.dtb \
+	meson-g12b-odroid-n2.dtb
 dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
 	tegra20-medcom-wide.dtb \
 	tegra20-paz00.dtb \
arch/arm/dts/meson-g12b-odroid-n2.dts new file +386 -0

386 lines not on this page · raw message

arch/arm/dts/meson-g12b.dtsi new file +82 -0

82 lines not on this page · raw message

include/dt-bindings/sound/meson-g12a-tohdmitx.h new file +13 -0
new file mode 100644
index 0000000000..c5e1f48d30
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __DT_MESON_G12A_TOHDMITX_H
+#define __DT_MESON_G12A_TOHDMITX_H
+
+#define TOHDMITX_I2S_IN_A	0
+#define TOHDMITX_I2S_IN_B	1
+#define TOHDMITX_I2S_IN_C	2
+#define TOHDMITX_I2S_OUT	3
+#define TOHDMITX_SPDIF_IN_A	4
+#define TOHDMITX_SPDIF_IN_B	5
+#define TOHDMITX_SPDIF_OUT	6
+
+#endif /* __DT_MESON_G12A_TOHDMITX_H */
Signature · 1 line
2.22.0
#2 lore raw

PATCH 1/3 ARM: dts: add support for Odroid-N2

Hi Neil,

Quoted 5 lines · Neil Armstrong

Import HardKernel Odroid-N2 DT from Linux 5.3-rc1, commit 5f9e832c1370 ("Linus 5.3-rc1") based on an Amlogic G12B S922X SoC.

Quoted 10 lines
---
 arch/arm/dts/Makefile                         |   3 +-
 arch/arm/dts/meson-g12b-odroid-n2.dts         | 386 ++++++++++++++++++
 arch/arm/dts/meson-g12b.dtsi                  |  82 ++++
 .../dt-bindings/sound/meson-g12a-tohdmitx.h   |  13 +
 4 files changed, 483 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/meson-g12b-odroid-n2.dts
 create mode 100644 arch/arm/dts/meson-g12b.dtsi
 create mode 100644 include/dt-bindings/sound/meson-g12a-tohdmitx.h

I am getting following error while building this on mainline u-boot.

  CHK     include/config/uboot.release
  UPD     include/config/uboot.release
  CHK     include/generated/version_autogenerated.h
  UPD     include/generated/version_autogenerated.h
  CHK     include/generated/timestamp_autogenerated.h
  UPD     include/generated/timestamp_autogenerated.h
  CHK     include/generated/generic-asm-offsets.h
  CHK     include/generated/asm-offsets.h
  HOSTCC  tools/mkenvimage.o
  HOSTLD  tools/mkenvimage
  HOSTCC  tools/dumpimage.o
  HOSTLD  tools/dumpimage
  HOSTCC  tools/mkimage.o
  HOSTLD  tools/mkimage
  CC      arch/arm/cpu/armv8/fwcall.o
  LD      arch/arm/cpu/armv8/built-in.o
  CC      cmd/version.o
  LD      cmd/built-in.o
  CC      common/main.o
  LD      common/built-in.o
  CC      lib/efi_loader/helloworld.o
  CC      lib/efi_loader/efi_reloc.o
  CC      lib/efi_loader/efi_freestanding.o
  LD      lib/efi_loader/helloworld_efi.so
  OBJCOPY lib/efi_loader/helloworld.efi
  CC      lib/smbios.o
  CC      lib/display_options.o
  LD      lib/built-in.o
  LD      u-boot

OBJCOPY u-boot.srec
OBJCOPY u-boot-nodtb.bin
start=$(aarch64-linux-gnu-nm u-boot | grep __rel_dyn_start | cut -f 1 -d ' '); end=$(aarch64-linux-gnu-nm u-boot | grep __rel_dyn_end | cut -f 1 -d ' '); tools/relocate-rela u-boot-nodtb.bin 0x01000000 $start $end
DTC arch/arm/dts/meson-g12b-odroid-n2.dtb
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:226.1-5 Label or path arb not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:244.1-12 Label or path clkc_audio not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:248.1-10 Label or path ext_mdio not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:264.1-8 Label or path ethmac not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:273.1-9 Label or path frddr_a not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:277.1-9 Label or path frddr_b not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:281.1-9 Label or path frddr_c not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:313.1-4 Label or path ir not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:320.1-11 Label or path sd_emmc_b not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:338.1-11 Label or path sd_emmc_c not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:356.1-9 Label or path tdmif_b not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:360.1-10 Label or path tdmout_b not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:364.1-10 Label or path tohdmitx not found
FATAL ERROR: Syntax error parsing input tree
make[2]: *** [scripts/Makefile.lib:308:
arch/arm/dts/meson-g12b-odroid-n2.dtb] Error 1
make[1]: *** [dts/Makefile:38: arch-dtbs] Error 2
make: *** [Makefile:1045: dts/dt.dtb] Error 2

Quoted 256 lines
arch/arm/dts/Makefile +2 -1
index f5535078c7..2baa368215 100644
@@ -135,7 +135,8 @@ dtb-$(CONFIG_ARCH_MESON) += \
        meson-gxl-s905x-khadas-vim.dtb \
        meson-gxm-khadas-vim2.dtb \
        meson-axg-s400.dtb \
-       meson-g12a-u200.dtb
+       meson-g12a-u200.dtb \
+       meson-g12b-odroid-n2.dtb
 dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
        tegra20-medcom-wide.dtb \
        tegra20-paz00.dtb \
arch/arm/dts/meson-g12b-odroid-n2.dts new file +236 -0
new file mode 100644
index 0000000000..81780ffcc7
@@ -0,0 +1,386 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+       compatible = "hardkernel,odroid-n2", "amlogic,g12b";
+       model = "Hardkernel ODROID-N2";
+
+       aliases {
+               serial0 = &uart_AO;
+               ethernet0 = &ethmac;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       memory at 0 {
+               device_type = "memory";
+               reg = <0x0 0x0 0x0 0x40000000>;
+       };
+
+       emmc_pwrseq: emmc-pwrseq {
+               compatible = "mmc-pwrseq-emmc";
+               reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               blue {
+                       label = "n2:blue";
+                       gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+                       linux,default-trigger = "heartbeat";
+               };
+       };
+
+       tflash_vdd: regulator-tflash_vdd {
+               compatible = "regulator-fixed";
+
+               regulator-name = "TFLASH_VDD";
+               regulator-min-microvolt = <3300000>;
+               regulator-max-microvolt = <3300000>;
+
+               gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>;
+               enable-active-high;
+       };
+
+       tf_io: gpio-regulator-tf_io {
+               compatible = "regulator-gpio";
+
+               regulator-name = "TF_IO";
+               regulator-min-microvolt = <1800000>;
+               regulator-max-microvolt = <3300000>;
+
+               gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+               gpios-states = <0>;
+
+               states = <3300000 0
+                         1800000 1>;
+       };
+
+       flash_1v8: regulator-flash_1v8 {
+               compatible = "regulator-fixed";
+               regulator-name = "FLASH_1V8";
+               regulator-min-microvolt = <1800000>;
+               regulator-max-microvolt = <1800000>;
+               vin-supply = <&vcc_3v3>;
+               regulator-always-on;
+       };
+
+       main_12v: regulator-main_12v {
+               compatible = "regulator-fixed";
+               regulator-name = "12V";
+               regulator-min-microvolt = <12000000>;
+               regulator-max-microvolt = <12000000>;
+               regulator-always-on;
+       };
+
+       vcc_5v: regulator-vcc_5v {
+               compatible = "regulator-fixed";
+               regulator-name = "5V";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               regulator-always-on;
+               vin-supply = <&main_12v>;
+       };
+
+       vcc_1v8: regulator-vcc_1v8 {
+               compatible = "regulator-fixed";
+               regulator-name = "VCC_1V8";
+               regulator-min-microvolt = <1800000>;
+               regulator-max-microvolt = <1800000>;
+               vin-supply = <&vcc_3v3>;
+               regulator-always-on;
+       };
+
+       vcc_3v3: regulator-vcc_3v3 {
+               compatible = "regulator-fixed";
+               regulator-name = "VCC_3V3";
+               regulator-min-microvolt = <3300000>;
+               regulator-max-microvolt = <3300000>;
+               vin-supply = <&vddao_3v3>;
+               regulator-always-on;
+               /* FIXME: actually controlled by VDDCPU_B_EN */
+       };
+
+       hub_5v: regulator-hub_5v {
+               compatible = "regulator-fixed";
+               regulator-name = "HUB_5V";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               vin-supply = <&vcc_5v>;
+
+               /* Connected to the Hub CHIPENABLE, LOW sets low power state */
+               gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
+               enable-active-high;
+       };
+
+       usb_pwr_en: regulator-usb_pwr_en {
+               compatible = "regulator-fixed";
+               regulator-name = "USB_PWR_EN";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               vin-supply = <&vcc_5v>;
+
+               /* Connected to the microUSB port power enable */
+               gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+               enable-active-high;
+       };
+
+       vddao_1v8: regulator-vddao_1v8 {
+               compatible = "regulator-fixed";
+               regulator-name = "VDDAO_1V8";
+               regulator-min-microvolt = <1800000>;
+               regulator-max-microvolt = <1800000>;
+               vin-supply = <&vddao_3v3>;
+               regulator-always-on;
+       };
+
+       vddao_3v3: regulator-vddao_3v3 {
+               compatible = "regulator-fixed";
+               regulator-name = "VDDAO_3V3";
+               regulator-min-microvolt = <3300000>;
+               regulator-max-microvolt = <3300000>;
+               vin-supply = <&main_12v>;
+               regulator-always-on;
+       };
+
+       hdmi-connector {
+               compatible = "hdmi-connector";
+               type = "a";
+
+               port {
+                       hdmi_connector_in: endpoint {
+                               remote-endpoint = <&hdmi_tx_tmds_out>;
+                       };
+               };
+       };
+
+       sound {
+               compatible = "amlogic,axg-sound-card";
+               model = "G12A-ODROIDN2";
+               audio-aux-devs = <&tdmout_b>;
+               audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+                               "TDMOUT_B IN 1", "FRDDR_B OUT 1",
+                               "TDMOUT_B IN 2", "FRDDR_C OUT 1",
+                               "TDM_B Playback", "TDMOUT_B OUT";
+
+               assigned-clocks = <&clkc CLKID_MPLL2>,
+                                 <&clkc CLKID_MPLL0>,
+                                 <&clkc CLKID_MPLL1>;
+               assigned-clock-parents = <0>, <0>, <0>;
+               assigned-clock-rates = <294912000>,
+                                      <270950400>,
+                                      <393216000>;
+               status = "okay";
+
+               dai-link-0 {
+                       sound-dai = <&frddr_a>;
+               };
+
+               dai-link-1 {
+                       sound-dai = <&frddr_b>;
+               };
+
+               dai-link-2 {
+                       sound-dai = <&frddr_c>;
+               };
+
+               /* 8ch hdmi interface */
+               dai-link-3 {
+                       sound-dai = <&tdmif_b>;
+                       dai-format = "i2s";
+                       dai-tdm-slot-tx-mask-0 = <1 1>;
+                       dai-tdm-slot-tx-mask-1 = <1 1>;
+                       dai-tdm-slot-tx-mask-2 = <1 1>;
+                       dai-tdm-slot-tx-mask-3 = <1 1>;
+                       mclk-fs = <256>;
+
+                       codec {
+                               sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+                       };
+               };
+
+               /* hdmi glue */
+               dai-link-4 {
+                       sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+                       codec {
+                               sound-dai = <&hdmi_tx>;
+                       };
+               };
+       };
+};
+
+&arb {
+       status = "okay";
+};
+
+&cec_AO {
+       pinctrl-0 = <&cec_ao_a_h_pins>;
+       pinctrl-names = "default";
+       status = "disabled";
+       hdmi-phandle = <&hdmi_tx>;
+};
+

arch/arm/dts/meson-g12b-odroid-n2.dts line 246

Quoted 10 lines
arch/arm/dts/meson-g12b-odroid-n2.dts new file +10 -0
+&cecb_AO {
+       pinctrl-0 = <&cec_ao_b_h_pins>;
+       pinctrl-names = "default";
+       status = "okay";
+       hdmi-phandle = <&hdmi_tx>;
+};
+
+&clkc_audio {
+       status = "okay";
+};

While applying this patch I get following warning.

Applying: ARM: dts: add support for Odroid-N2
.git/rebase-apply/patch:280: trailing whitespace.

                /* Realtek RTL8211F (0x001cc916) */

warning: 1 line adds whitespace errors.

Quoted 254 lines
arch/arm/dts/meson-g12b-odroid-n2.dts new file +140 -0
+
+&ext_mdio {
+       external_phy: ethernet-phy at 0 {
+               /* Realtek RTL8211F (0x001cc916) */
+               reg = <0>;
+               max-speed = <1000>;
+
+               reset-assert-us = <10000>;
+               reset-deassert-us = <30000>;
+               reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+
+               interrupt-parent = <&gpio_intc>;
+               /* MAC_INTR on GPIOZ_14 */
+               interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+       };
+};
+
+&ethmac {
+       pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
+       pinctrl-names = "default";
+       status = "okay";
+       phy-mode = "rgmii";
+       phy-handle = <&external_phy>;
+       amlogic,tx-delay-ns = <2>;
+};
+
+&frddr_a {
+       status = "okay";
+};
+
+&frddr_b {
+       status = "okay";
+};
+
+&frddr_c {
+       status = "okay";
+};
+
+&gpio {
+       /*
+        * WARNING: The USB Hub on the Odroid-N2 needs a reset signal
+        * to be turned high in order to be detected by the USB Controller
+        * This signal should be handled by a USB specific power sequence
+        * in order to reset the Hub when USB bus is powered down.
+        */
+       usb-hub {
+               gpio-hog;
+               gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
+               output-high;
+               line-name = "usb-hub-reset";
+       };
+};
+
+&hdmi_tx {
+       status = "okay";
+       pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+       pinctrl-names = "default";
+       hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+       hdmi_tx_tmds_out: endpoint {
+               remote-endpoint = <&hdmi_connector_in>;
+       };
+};
+
+&ir {
+       status = "okay";
+       pinctrl-0 = <&remote_input_ao_pins>;
+       pinctrl-names = "default";
+};
+
+/* SD card */
+&sd_emmc_b {
+       status = "okay";
+       pinctrl-0 = <&sdcard_c_pins>;
+       pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+       pinctrl-names = "default", "clk-gate";
+
+       bus-width = <4>;
+       cap-sd-highspeed;
+       max-frequency = <50000000>;
+       disable-wp;
+
+       cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+       vmmc-supply = <&tflash_vdd>;
+       vqmmc-supply = <&tf_io>;
+
+};
+
+/* eMMC */
+&sd_emmc_c {
+       status = "okay";
+       pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+       pinctrl-1 = <&emmc_clk_gate_pins>;
+       pinctrl-names = "default", "clk-gate";
+
+       bus-width = <8>;
+       cap-mmc-highspeed;
+       mmc-ddr-1_8v;
+       mmc-hs200-1_8v;
+       max-frequency = <200000000>;
+       disable-wp;
+
+       mmc-pwrseq = <&emmc_pwrseq>;
+       vmmc-supply = <&vcc_3v3>;
+       vqmmc-supply = <&flash_1v8>;
+};
+
+&tdmif_b {
+       status = "okay";
+};
+
+&tdmout_b {
+       status = "okay";
+};
+
+&tohdmitx {
+       status = "okay";
+};
+
+&uart_AO {
+       status = "okay";
+       pinctrl-0 = <&uart_ao_a_pins>;
+       pinctrl-names = "default";
+};
+
+&usb {
+       status = "okay";
+       vbus-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy0 {
+       phy-supply = <&vcc_5v>;
+};
+
+&usb2_phy1 {
+       /* Enable the hub which is connected to this port */
+       phy-supply = <&hub_5v>;
+};
arch/arm/dts/meson-g12b.dtsi new file +82 -0
new file mode 100644
index 0000000000..9e88e513b2
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <[email protected]>
+ */
+
+#include "meson-g12a.dtsi"
+
+/ {
+       compatible = "amlogic,g12b";
+
+       cpus {
+               cpu-map {
+                       cluster0 {
+                               core0 {
+                                       cpu = <&cpu0>;
+                               };
+
+                               core1 {
+                                       cpu = <&cpu1>;
+                               };
+                       };
+
+                       cluster1 {
+                               core0 {
+                                       cpu = <&cpu100>;
+                               };
+
+                               core1 {
+                                       cpu = <&cpu101>;
+                               };
+
+                               core2 {
+                                       cpu = <&cpu102>;
+                               };
+
+                               core3 {
+                                       cpu = <&cpu103>;
+                               };
+                       };
+               };
+
+               /delete-node/ cpu at 2;
+               /delete-node/ cpu at 3;
+
+               cpu100: cpu at 100 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a73";
+                       reg = <0x0 0x100>;
+                       enable-method = "psci";
+                       next-level-cache = <&l2>;
+               };
+
+               cpu101: cpu at 101 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a73";
+                       reg = <0x0 0x101>;
+                       enable-method = "psci";
+                       next-level-cache = <&l2>;
+               };
+
+               cpu102: cpu at 102 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a73";
+                       reg = <0x0 0x102>;
+                       enable-method = "psci";
+                       next-level-cache = <&l2>;
+               };
+
+               cpu103: cpu at 103 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a73";
+                       reg = <0x0 0x103>;
+                       enable-method = "psci";
+                       next-level-cache = <&l2>;
+               };
+       };
+};
+
+&clkc {
+       compatible = "amlogic,g12b-clkc";
+};
include/dt-bindings/sound/meson-g12a-tohdmitx.h new file +13 -1
new file mode 100644
index 0000000000..c5e1f48d30
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __DT_MESON_G12A_TOHDMITX_H
+#define __DT_MESON_G12A_TOHDMITX_H
+
+#define TOHDMITX_I2S_IN_A      0
+#define TOHDMITX_I2S_IN_B      1
+#define TOHDMITX_I2S_IN_C      2
+#define TOHDMITX_I2S_OUT       3
+#define TOHDMITX_SPDIF_IN_A    4
+#define TOHDMITX_SPDIF_IN_B    5
+#define TOHDMITX_SPDIF_OUT     6
+
+#endif /* __DT_MESON_G12A_TOHDMITX_H */
--

2.22.0

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

#3 lore raw

PATCH 1/3 ARM: dts: add support for Odroid-N2

Hi Anand,

Quoted 19 lines · Anand Moon

Hi Neil,

Quoted 5 lines · Neil Armstrong

Import HardKernel Odroid-N2 DT from Linux 5.3-rc1, commit 5f9e832c1370 ("Linus 5.3-rc1") based on an Amlogic G12B S922X SoC.

Quoted 10 lines
---
 arch/arm/dts/Makefile                         |   3 +-
 arch/arm/dts/meson-g12b-odroid-n2.dts         | 386 ++++++++++++++++++
 arch/arm/dts/meson-g12b.dtsi                  |  82 ++++
 .../dt-bindings/sound/meson-g12a-tohdmitx.h   |  13 +
 4 files changed, 483 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/meson-g12b-odroid-n2.dts
 create mode 100644 arch/arm/dts/meson-g12b.dtsi
 create mode 100644 include/dt-bindings/sound/meson-g12a-tohdmitx.h
Quoted 1 line

I am getting following error while building this on mainline u-boot.

I forgot to explicit in the cover letter, but you'll need https://patchwork.ozlabs.org/patch/1134772/
before this serie.

Neil

Quoted 70 lines
  CHK     include/config/uboot.release
  UPD     include/config/uboot.release
  CHK     include/generated/version_autogenerated.h
  UPD     include/generated/version_autogenerated.h
  CHK     include/generated/timestamp_autogenerated.h
  UPD     include/generated/timestamp_autogenerated.h
  CHK     include/generated/generic-asm-offsets.h
  CHK     include/generated/asm-offsets.h
  HOSTCC  tools/mkenvimage.o
  HOSTLD  tools/mkenvimage
  HOSTCC  tools/dumpimage.o
  HOSTLD  tools/dumpimage
  HOSTCC  tools/mkimage.o
  HOSTLD  tools/mkimage
  CC      arch/arm/cpu/armv8/fwcall.o
  LD      arch/arm/cpu/armv8/built-in.o
  CC      cmd/version.o
  LD      cmd/built-in.o
  CC      common/main.o
  LD      common/built-in.o
  CC      lib/efi_loader/helloworld.o
  CC      lib/efi_loader/efi_reloc.o
  CC      lib/efi_loader/efi_freestanding.o
  LD      lib/efi_loader/helloworld_efi.so
  OBJCOPY lib/efi_loader/helloworld.efi
  CC      lib/smbios.o
  CC      lib/display_options.o
  LD      lib/built-in.o
  LD      u-boot

OBJCOPY u-boot.srec
OBJCOPY u-boot-nodtb.bin
start=$(aarch64-linux-gnu-nm u-boot | grep __rel_dyn_start | cut -f 1

(quoted diff) +0 -2
-d ' '); end=$(aarch64-linux-gnu-nm u-boot | grep __rel_dyn_end | cut
-f 1 -d ' '); tools/relocate-rela u-boot-nodtb.bin 0x01000000 $start

$end
DTC arch/arm/dts/meson-g12b-odroid-n2.dtb
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:226.1-5 Label or path arb not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:244.1-12 Label or path clkc_audio not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:248.1-10 Label or path ext_mdio not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:264.1-8 Label or path ethmac not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:273.1-9 Label or path frddr_a not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:277.1-9 Label or path frddr_b not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:281.1-9 Label or path frddr_c not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:313.1-4 Label or path ir not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:320.1-11 Label or path sd_emmc_b not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:338.1-11 Label or path sd_emmc_c not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:356.1-9 Label or path tdmif_b not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:360.1-10 Label or path tdmout_b not found
Error: arch/arm/dts/.meson-g12b-odroid-n2.dtb.pre.tmp:364.1-10 Label or path tohdmitx not found
FATAL ERROR: Syntax error parsing input tree
make[2]: *** [scripts/Makefile.lib:308:
arch/arm/dts/meson-g12b-odroid-n2.dtb] Error 1
make[1]: *** [dts/Makefile:38: arch-dtbs] Error 2
make: *** [Makefile:1045: dts/dt.dtb] Error 2

[..]

#4 lore raw

PATCH 2/3 ARM: meson-g12a: Handle 4GiB DRAM size

In reply to Neil Armstrong

When configured with 4GiB DRAM size, only 3.8GiB is available, the I/O beeing mapped in the last 256MiB of the first 4GiB physical memory/

First fixup the mm_region to handle the first 3.8GiB as memory and the last 256MiB as I/O.

Then limit the real memory reported by the firmware to the available physical space, 3.8GiB aligned with the mm_region memory zone size.

---
 arch/arm/mach-meson/board-g12a.c | 13 +++++++------
 1 file changed, 7 insertions(+), 6 deletions(-)
arch/arm/mach-meson/board-g12a.c +7 -6
index 1652970fbd..546b9f6039 100644
@@ -62,21 +62,21 @@ void meson_init_reserved_memory(void *fdt)
 phys_size_t get_effective_memsize(void)
 {
 	/* Size is reported in MiB, convert it in bytes */
-	return ((readl(G12A_AO_SEC_GP_CFG0) & G12A_AO_MEM_SIZE_MASK)
-			>> G12A_AO_MEM_SIZE_SHIFT) * SZ_1M;
+	return min(((readl(G12A_AO_SEC_GP_CFG0) & G12A_AO_MEM_SIZE_MASK)
+			>> G12A_AO_MEM_SIZE_SHIFT) * SZ_1M, 0xf5000000);
 }
 
 static struct mm_region g12a_mem_map[] = {
 	{
 		.virt = 0x0UL,
 		.phys = 0x0UL,
-		.size = 0x80000000UL,
+		.size = 0xf5000000UL,
 		.attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
 			 PTE_BLOCK_INNER_SHARE
 	}, {
-		.virt = 0xf0000000UL,
-		.phys = 0xf0000000UL,
-		.size = 0x10000000UL,
+		.virt = 0xf5000000UL,
+		.phys = 0xf5000000UL,
+		.size = 0x0b000000UL,
 		.attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
 			 PTE_BLOCK_NON_SHARE |
 			 PTE_BLOCK_PXN | PTE_BLOCK_UXN
@@ -129,6 +129,7 @@ void meson_eth_init(phy_interface_t mode, unsigned int flags)
 			     G12A_ETH_REG_0_TX_RATIO(4) |
 			     G12A_ETH_REG_0_PHY_CLK_EN |
 			     G12A_ETH_REG_0_CLK_EN);
+		g12a_enable_external_mdio();
 		break;
 
 	case PHY_INTERFACE_MODE_RMII:
Signature · 1 line
2.22.0
#5 lore raw

PATCH 3/3 board: amlogic: add support for Odroid-N2

In reply to Neil Armstrong

ODROID-N2 is a single board computer manufactured by Hardkernel Co. Ltd with the following specifications:

- Amlogic S922X ARM Cortex-A53 dual-core + Cortex-A73 quad-core SoC
- 4GB DDR4 SDRAM
- Gigabit Ethernet
- HDMI 2.1 4K/60Hz display
- 40-pin GPIO header
- 4 x USB 3.0 Host, 1 x USB OTG
- eMMC, microSD
- Infrared receiver

The board directory is W400, the name of the Amlogic Reference Design of Amlogic G12B with Gigabit boards, which will be used for similar boards.

---
 board/amlogic/w400/MAINTAINERS      |   6 ++
 board/amlogic/w400/Makefile         |   6 ++
 board/amlogic/w400/README.odroid-n2 | 130 ++++++++++++++++++++++++++++
 board/amlogic/w400/README.w400      | 130 ++++++++++++++++++++++++++++
 board/amlogic/w400/w400.c           |  18 ++++
 configs/odroid-n2_defconfig         |  56 ++++++++++++
 6 files changed, 346 insertions(+)
 create mode 100644 board/amlogic/w400/MAINTAINERS
 create mode 100644 board/amlogic/w400/Makefile
 create mode 100644 board/amlogic/w400/README.odroid-n2
 create mode 100644 board/amlogic/w400/README.w400
 create mode 100644 board/amlogic/w400/w400.c
 create mode 100644 configs/odroid-n2_defconfig
board/amlogic/w400/MAINTAINERS new file +6 -0
new file mode 100644
index 0000000000..6e68fa73f7
@@ -0,0 +1,6 @@
+W400
+M:	Neil Armstrong <[email protected]>
+S:	Maintained
+L:	u-boot-amlogic at groups.io
+F:	board/amlogic/w400/
+F:	configs/odroid-n2_defconfig
board/amlogic/w400/Makefile new file +6 -0
new file mode 100644
index 0000000000..fac4a73afa
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2019 BayLibre, SAS
+# Author: Neil Armstrong <[email protected]>
+
+obj-y	:= w400.o
board/amlogic/w400/README.odroid-n2 new file +130 -0

130 lines not on this page · raw message

board/amlogic/w400/README.w400 new file +130 -0

130 lines not on this page · raw message

board/amlogic/w400/w400.c new file +18 -0
new file mode 100644
index 0000000000..4737865367
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 BayLibre, SAS
+ * Author: Neil Armstrong <[email protected]>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <environment.h>
+#include <asm/io.h>
+#include <asm/arch/eth.h>
+
+int misc_init_r(void)
+{
+	meson_eth_init(PHY_INTERFACE_MODE_RGMII, 0);
+
+	return 0;
+}
configs/odroid-n2_defconfig new file +56 -0

56 lines not on this page · raw message

Signature · 1 line
2.22.0
#6 lore raw

PATCH 3/3 board: amlogic: add support for Odroid-N2

Hi Neil,

Quoted 101 lines · Neil Armstrong

ODROID-N2 is a single board computer manufactured by Hardkernel Co. Ltd with the following specifications:

- Amlogic S922X ARM Cortex-A53 dual-core + Cortex-A73 quad-core SoC
- 4GB DDR4 SDRAM
- Gigabit Ethernet
- HDMI 2.1 4K/60Hz display
- 40-pin GPIO header
- 4 x USB 3.0 Host, 1 x USB OTG
- eMMC, microSD
- Infrared receiver

The board directory is W400, the name of the Amlogic Reference Design of Amlogic G12B with Gigabit boards, which will be used for similar boards.

---
 board/amlogic/w400/MAINTAINERS      |   6 ++
 board/amlogic/w400/Makefile         |   6 ++
 board/amlogic/w400/README.odroid-n2 | 130 ++++++++++++++++++++++++++++
 board/amlogic/w400/README.w400      | 130 ++++++++++++++++++++++++++++
 board/amlogic/w400/w400.c           |  18 ++++
 configs/odroid-n2_defconfig         |  56 ++++++++++++
 6 files changed, 346 insertions(+)
 create mode 100644 board/amlogic/w400/MAINTAINERS
 create mode 100644 board/amlogic/w400/Makefile
 create mode 100644 board/amlogic/w400/README.odroid-n2
 create mode 100644 board/amlogic/w400/README.w400
 create mode 100644 board/amlogic/w400/w400.c
 create mode 100644 configs/odroid-n2_defconfig
board/amlogic/w400/MAINTAINERS new file +6 -0
new file mode 100644
index 0000000000..6e68fa73f7
@@ -0,0 +1,6 @@
+W400
+M:     Neil Armstrong <[email protected]>
+S:     Maintained
+L:     u-boot-amlogic at groups.io
+F:     board/amlogic/w400/
+F:     configs/odroid-n2_defconfig
board/amlogic/w400/Makefile new file +6 -0
new file mode 100644
index 0000000000..fac4a73afa
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2019 BayLibre, SAS
+# Author: Neil Armstrong <[email protected]>
+
+obj-y  := w400.o
board/amlogic/w400/README.odroid-n2 new file +38 -0
new file mode 100644
index 0000000000..90070a988d
@@ -0,0 +1,130 @@
+U-Boot for ODROID-N2
+====================
+
+ODROID-N2 is a single board computer manufactured by Hardkernel
+Co. Ltd with the following specifications:
+
+ - Amlogic S922X ARM Cortex-A53 dual-core + Cortex-A73 quad-core SoC
+ - 4GB DDR4 SDRAM
+ - Gigabit Ethernet
+ - HDMI 2.1 4K/60Hz display
+ - 40-pin GPIO header
+ - 4 x USB 3.0 Host, 1 x USB OTG
+ - eMMC, microSD
+ - Infrared receiver
+
+Schematics are available on the manufacturer website.
+
+Currently the u-boot port supports the following devices:
+ - serial
+ - eMMC, microSD
+ - Ethernet
+ - I2C
+ - Regulators
+ - Reset controller
+ - Clock controller
+ - ADC
+
+u-boot compilation
+==================
+
+ > export ARCH=arm
+ > export CROSS_COMPILE=aarch64-none-elf-
+ > make odroid-n2_defconfig
+ > make
+
+Image creation
+==============
+

board/amlogic/w400/README.odroid-n2 line 48

Quoted 10 lines
board/amlogic/w400/README.odroid-n2 new file +10 -0
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+

Should we checkout odroidn2-v2015.01 from Hardkernel repository.

Quoted 311 lines
board/amlogic/w400/README.odroid-n2 new file +82 -0
+ > DIR=odroid-c2
+ > git clone --depth 1 \
+       https://github.com/hardkernel/u-boot.git -b odroidc2-v2015.01 \
+       $DIR
+
+ > cd odroid-c2
+ > make odroidn2_defconfig
+ > make
+ > export UBOOTDIR=$PWD
+
+ Go back to mainline U-Boot source tree then :
+ > mkdir fip
+
+ > wget https://github.com/BayLibre/u-boot/releases/download/v2017.11-libretech-cc/blx_fix_g12a.sh -O fip/blx_fix.sh
+ > cp $UBOOTDIR/build/scp_task/bl301.bin fip/
+ > cp $UBOOTDIR/build/board/hardkernel/odroidn2/firmware/acs.bin fip/
+ > cp $UBOOTDIR/fip/g12b/bl2.bin fip/
+ > cp $UBOOTDIR/fip/g12b/bl30.bin fip/
+ > cp $UBOOTDIR/fip/g12b/bl31.img fip/
+ > cp $UBOOTDIR/fip/g12b/ddr3_1d.fw fip/
+ > cp $UBOOTDIR/fip/g12b/ddr4_1d.fw fip/
+ > cp $UBOOTDIR/fip/g12b/ddr4_2d.fw fip/
+ > cp $UBOOTDIR/fip/g12b/diag_lpddr4.fw fip/
+ > cp $UBOOTDIR/fip/g12b/lpddr4_1d.fw fip/
+ > cp $UBOOTDIR/fip/g12b/lpddr4_2d.fw fip/
+ > cp $UBOOTDIR/fip/g12b/piei.fw fip/
+ > cp $UBOOTDIR/fip/g12b/aml_ddr.fw fip/
+ > cp u-boot.bin fip/bl33.bin
+
+ > sh fip/blx_fix.sh \
+       fip/bl30.bin \
+       fip/zero_tmp \
+       fip/bl30_zero.bin \
+       fip/bl301.bin \
+       fip/bl301_zero.bin \
+       fip/bl30_new.bin \
+       bl30
+
+ > sh fip/blx_fix.sh \
+       fip/bl2.bin \
+       fip/zero_tmp \
+       fip/bl2_zero.bin \
+       fip/acs.bin \
+       fip/bl21_zero.bin \
+       fip/bl2_new.bin \
+       bl2
+
+ > $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl30sig --input fip/bl30_new.bin \
+                                       --output fip/bl30_new.bin.g12a.enc \
+                                       --level v3
+ > $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl3sig --input fip/bl30_new.bin.g12a.enc \
+                                       --output fip/bl30_new.bin.enc \
+                                       --level v3 --type bl30
+ > $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl3sig --input fip/bl31.img \
+                                       --output fip/bl31.img.enc \
+                                       --level v3 --type bl31
+ > $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl3sig --input fip/bl33.bin --compress lz4 \
+                                       --output fip/bl33.bin.enc \
+                                       --level v3 --type bl33 --compress lz4
+ > $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl2sig --input fip/bl2_new.bin \
+                                       --output fip/bl2.n.bin.sig
+ > $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bootmk \
+               --output fip/u-boot.bin \
+               --bl2 fip/bl2.n.bin.sig \
+               --bl30 fip/bl30_new.bin.enc \
+               --bl31 fip/bl31.img.enc \
+               --bl33 fip/bl33.bin.enc \
+               --ddrfw1 fip/ddr4_1d.fw \
+               --ddrfw2 fip/ddr4_2d.fw \
+               --ddrfw3 fip/ddr3_1d.fw \
+               --ddrfw4 fip/piei.fw \
+               --ddrfw5 fip/lpddr4_1d.fw \
+               --ddrfw6 fip/lpddr4_2d.fw \
+               --ddrfw7 fip/diag_lpddr4.fw \
+               --ddrfw8 fip/aml_ddr.fw \
+               --level v3
+
+and then write the image to SD with:
+
+ > DEV=/dev/your_sd_device
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
board/amlogic/w400/README.w400 new file +130 -0
new file mode 100644
index 0000000000..25b786d817
@@ -0,0 +1,130 @@
+U-Boot for Amlogic W400
+=======================
+
+U200 is a reference board manufactured by Amlogic with the following
+specifications:
+
+ - Amlogic S922X ARM Cortex-A53 dual-core + Cortex-A73 quad-core SoC
+ - 2GB DDR4 SDRAM
+ - 10/100 Ethernet (Internal PHY)
+ - 1 x USB 3.0 Host
+ - eMMC
+ - SDcard
+ - Infrared receiver
+ - SDIO WiFi Module
+ - MIPI DSI Connector
+ - Audio HAT Connector
+ - PCI-E M.2 Connector
+
+Schematics are available from Amlogic on demand.
+
+Currently the u-boot port supports the following devices:
+ - serial
+ - Ethernet
+ - Regulators
+ - Clock controller
+
+u-boot compilation
+==================
+
+ > export ARCH=arm
+ > export CROSS_COMPILE=aarch64-none-elf-
+ > make w400_defconfig
+ > make
+
+Image creation
+==============
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+ > git clone https://github.com/BayLibre/u-boot.git -b buildroot-openlinux-20180418 amlogic-u-boot
+ > cd amlogic-u-boot
+ > make g12b_w400_v1_defconfig
+ > make
+ > export UBOOTDIR=$PWD
+
+Download the latest Amlogic Buildroot package, and extract it :
+ > wget http://openlinux2.amlogic.com:8000/ARM/filesystem/Linux_BSP/buildroot_openlinux_kernel_4.9_fbdev_20180706.tar.gz
+ > tar xfz buildroot_openlinux_kernel_4.9_fbdev_20180706.tar.gz buildroot_openlinux_kernel_4.9_fbdev_20180706/bootloader
+ > export BRDIR=$PWD/buildroot_openlinux_kernel_4.9_fbdev_20180706
+ > export FIPDIR=$BRDIR/bootloader/uboot-repo/fip
+
+Go back to mainline U-Boot source tree then :
+ > mkdir fip
+
+ > wget https://github.com/BayLibre/u-boot/releases/download/v2017.11-libretech-cc/blx_fix_g12a.sh -O fip/blx_fix.sh
+ > cp $UBOOTDIR/build/scp_task/bl301.bin fip/
+ > cp $UBOOTDIR/build/board/amlogic/g12b_w400_v1/firmware/acs.bin fip/
+ > cp $BRDIR/bootloader/uboot-repo/bl2/bin/g12b/bl2.bin fip/
+ > cp $BRDIR/bootloader/uboot-repo/bl30/bin/g12b/bl30.bin fip/
+ > cp $BRDIR/bootloader/uboot-repo/bl31_1.3/bin/g12b/bl31.img fip/
+ > cp $FIPDIR/g12b/ddr3_1d.fw fip/
+ > cp $FIPDIR/g12b/ddr4_1d.fw fip/
+ > cp $FIPDIR/g12b/ddr4_2d.fw fip/
+ > cp $FIPDIR/g12b/diag_lpddr4.fw fip/
+ > cp $FIPDIR/g12b/lpddr4_1d.fw fip/
+ > cp $FIPDIR/g12b/lpddr4_2d.fw fip/
+ > cp $FIPDIR/g12b/piei.fw fip/
+ > cp $FIPDIR/g12b/aml_ddr.fw fip/
+ > cp u-boot.bin fip/bl33.bin
+
+ > sh fip/blx_fix.sh \
+       fip/bl30.bin \
+       fip/zero_tmp \
+       fip/bl30_zero.bin \
+       fip/bl301.bin \
+       fip/bl301_zero.bin \
+       fip/bl30_new.bin \
+       bl30
+
+ > sh fip/blx_fix.sh \
+       fip/bl2.bin \
+       fip/zero_tmp \
+       fip/bl2_zero.bin \
+       fip/acs.bin \
+       fip/bl21_zero.bin \
+       fip/bl2_new.bin \
+       bl2
+
+ > $FIPDIR/g12b/aml_encrypt_g12b --bl30sig --input fip/bl30_new.bin \
+                                       --output fip/bl30_new.bin.g12a.enc \
+                                       --level v3
+ > $FIPDIR/g12b/aml_encrypt_g12b --bl3sig --input fip/bl30_new.bin.g12a.enc \
+                                       --output fip/bl30_new.bin.enc \
+                                       --level v3 --type bl30
+ > $FIPDIR/g12b/aml_encrypt_g12b --bl3sig --input fip/bl31.img \
+                                       --output fip/bl31.img.enc \
+                                       --level v3 --type bl31
+ > $FIPDIR/g12b/aml_encrypt_g12b --bl3sig --input fip/bl33.bin --compress lz4 \
+                                       --output fip/bl33.bin.enc \
+                                       --level v3 --type bl33
+ > $FIPDIR/g12b/aml_encrypt_g12b --bl2sig --input fip/bl2_new.bin \
+                                       --output fip/bl2.n.bin.sig
+ > $FIPDIR/g12b/aml_encrypt_g12b --bootmk \
+               --output fip/u-boot.bin \
+               --bl2 fip/bl2.n.bin.sig \
+               --bl30 fip/bl30_new.bin.enc \
+               --bl31 fip/bl31.img.enc \
+               --bl33 fip/bl33.bin.enc \
+               --ddrfw1 fip/ddr4_1d.fw \
+               --ddrfw2 fip/ddr4_2d.fw \
+               --ddrfw3 fip/ddr3_1d.fw \
+               --ddrfw4 fip/piei.fw \
+               --ddrfw5 fip/lpddr4_1d.fw \
+               --ddrfw6 fip/lpddr4_2d.fw \
+               --ddrfw7 fip/diag_lpddr4.fw \
+               --ddrfw8 fip/aml_ddr.fw \
+               --level v3
+
+and then write the image to SD with:
+
+ > DEV=/dev/your_sd_device
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
board/amlogic/w400/w400.c new file +18 -0
new file mode 100644
index 0000000000..4737865367
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 BayLibre, SAS
+ * Author: Neil Armstrong <[email protected]>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <environment.h>
+#include <asm/io.h>
+#include <asm/arch/eth.h>
+
+int misc_init_r(void)
+{
+       meson_eth_init(PHY_INTERFACE_MODE_RGMII, 0);
+
+       return 0;
+}
configs/odroid-n2_defconfig new file +56 -1
new file mode 100644
index 0000000000..38d1549375
@@ -0,0 +1,56 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MESON=y
+CONFIG_SYS_TEXT_BASE=0x01000000
+CONFIG_MESON_G12A=y
+CONFIG_SYS_BOARD="w400"
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_DEBUG_UART_BASE=0xff803000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" odroid-n2"
+CONFIG_DEBUG_UART=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_MISC_INIT_R=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="meson-g12b-odroid-n2"
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_PHY_REALTEK=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_G12A=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DEBUG_UART_MESON=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_USB=y
+CONFIG_USB_HOST=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_PHY=y
+CONFIG_MESON_G12A_USB_PHY=y
+CONFIG_DM_USB=y
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_MESON_G12A=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e
+CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
--

2.22.0

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot

#7 lore raw

PATCH 3/3 board: amlogic: add support for Odroid-N2

Hi Anand,

Quoted 36 lines · Anand Moon

Hi Neil,

Quoted 33 lines · Neil Armstrong

ODROID-N2 is a single board computer manufactured by Hardkernel Co. Ltd with the following specifications:

- Amlogic S922X ARM Cortex-A53 dual-core + Cortex-A73 quad-core SoC
- 4GB DDR4 SDRAM
- Gigabit Ethernet
- HDMI 2.1 4K/60Hz display
- 40-pin GPIO header
- 4 x USB 3.0 Host, 1 x USB OTG
- eMMC, microSD
- Infrared receiver

The board directory is W400, the name of the Amlogic Reference Design of Amlogic G12B with Gigabit boards, which will be used for similar boards.

---
 board/amlogic/w400/MAINTAINERS      |   6 ++
 board/amlogic/w400/Makefile         |   6 ++
 board/amlogic/w400/README.odroid-n2 | 130 ++++++++++++++++++++++++++++
 board/amlogic/w400/README.w400      | 130 ++++++++++++++++++++++++++++
 board/amlogic/w400/w400.c           |  18 ++++
 configs/odroid-n2_defconfig         |  56 ++++++++++++
 6 files changed, 346 insertions(+)
 create mode 100644 board/amlogic/w400/MAINTAINERS
 create mode 100644 board/amlogic/w400/Makefile
 create mode 100644 board/amlogic/w400/README.odroid-n2
 create mode 100644 board/amlogic/w400/README.w400
 create mode 100644 board/amlogic/w400/w400.c
 create mode 100644 configs/odroid-n2_defconfig

[..]

Quoted 9 lines

board/amlogic/w400/README.odroid-n2 line 48

Quoted 7 lines
board/amlogic/w400/README.odroid-n2 new file +7 -0
+
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+

Should we checkout odroidn2-v2015.01 from Hardkernel repository.

Yes, you are right it's a typo !

Quoted 7 lines

board/amlogic/w400/README.odroid-n2 line 53

Quoted 7 lines

+ > DIR=odroid-c2
+ > git clone --depth 1 \

board/amlogic/w400/README.odroid-n2 new file +3 -0
+       https://github.com/hardkernel/u-boot.git -b odroidc2-v2015.01 \
+       $DIR
+

[..]

Thanks,
Neil