ARM: dts: sunxi: Remove simple-panel compatible
Subsystems (2)
PATCH 1/2 ARM: dts: sunxi: Remove simple-panel compatible
simple-panel based bindings need only the display compatible, and simple-panel isn't documented anywhere. Remove it.
--- arch/arm/boot/dts/sun5i-a13-q8-tablet.dts | 2 +- arch/arm/boot/dts/sun8i-a23-q8-tablet.dts | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
arch/arm/boot/dts/sun5i-a13-q8-tablet.dts +1 -1
@@ -49,7 +49,7 @@ compatible = "allwinner,q8-a13", "allwinner,sun5i-a13"; panel: panel { - compatible = "bananapi,s070wv20-ct16", "simple-panel"; + compatible = "bananapi,s070wv20-ct16"; power-supply = <®_vcc3v3>; enable-gpios = <&axp_gpio 0 GPIO_ACTIVE_HIGH>; /* AXP GPIO0 */ backlight = <&backlight>;
arch/arm/boot/dts/sun8i-a23-q8-tablet.dts +1 -1
@@ -63,7 +63,7 @@ }; &panel { - compatible = "bananapi,s070wv20-ct16", "simple-panel"; + compatible = "bananapi,s070wv20-ct16"; }; &tcon0_out {
Signature · 7 lines
2.21.0 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH 2/2 ARM: dts: sunxi: Fix the HDMI PHY name
Even though the binding mentions that the PHY name must be "phy", it turns out that all our DTs had "hdmi-phy" instead.
The code doesn't care about the phy-names property, so we can just change our DTs to match the binding, without any side effect.
--- arch/arm/boot/dts/sun8i-a83t.dtsi | 2 +- arch/arm/boot/dts/sun8i-r40.dtsi | 2 +- arch/arm/boot/dts/sunxi-h3-h5.dtsi | 2 +- arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 2 +- arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 2 +- 5 files changed, 5 insertions(+), 5 deletions(-)
arch/arm/boot/dts/sun8i-a83t.dtsi +1 -1
@@ -1036,7 +1036,7 @@ resets = <&ccu RST_BUS_HDMI1>; reset-names = "ctrl"; phys = <&hdmi_phy>; - phy-names = "hdmi-phy"; + phy-names = "phy"; pinctrl-names = "default"; pinctrl-0 = <&hdmi_pins>; status = "disabled";
arch/arm/boot/dts/sun8i-r40.dtsi +1 -1
@@ -809,7 +809,7 @@ resets = <&ccu RST_BUS_HDMI1>; reset-names = "ctrl"; phys = <&hdmi_phy>; - phy-names = "hdmi-phy"; + phy-names = "phy"; status = "disabled"; ports {
arch/arm/boot/dts/sunxi-h3-h5.dtsi +1 -1
@@ -765,7 +765,7 @@ resets = <&ccu RST_BUS_HDMI1>; reset-names = "ctrl"; phys = <&hdmi_phy>; - phy-names = "hdmi-phy"; + phy-names = "phy"; status = "disabled"; ports {
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi +1 -1
@@ -1015,7 +1015,7 @@ resets = <&ccu RST_BUS_HDMI1>; reset-names = "ctrl"; phys = <&hdmi_phy>; - phy-names = "hdmi-phy"; + phy-names = "phy"; status = "disabled"; ports {
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +1 -1
@@ -504,7 +504,7 @@ resets = <&ccu RST_BUS_HDMI_SUB>, <&ccu RST_BUS_HDCP>; reset-names = "ctrl", "hdcp"; phys = <&hdmi_phy>; - phy-names = "hdmi-phy"; + phy-names = "phy"; pinctrl-names = "default"; pinctrl-0 = <&hdmi_pins>; status = "disabled";
Signature · 7 lines
2.21.0 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH 2/2] ARM: dts: sunxi: Fix the HDMI PHY name
Quoted 8 lines · Maxime Ripard
Even though the binding mentions that the PHY name must be "phy", it turns out that all our DTs had "hdmi-phy" instead.
The code doesn't care about the phy-names property, so we can just change our DTs to match the binding, without any side effect.
Signed-off-by Maxime Ripard <[email protected]>
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 5 lines · Maxime Ripard
simple-panel based bindings need only the display compatible, and simple-panel isn't documented anywhere. Remove it.
Signed-off-by Maxime Ripard <[email protected]>
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel