5.1.20-stable review
Subsystems (8)
Greg Kroah-Hartman
maintainercover 5.1.20-stable review
This is the start of the stable review cycle for the 5.1.20 release. There are 371 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.
Responses should be made by Fri 26 Jul 2019 07:13:35 PM UTC. Anything received after that time might be too late.
The whole patch series can be found in one patch at:
https://www.kernel.org/pub/linux/kernel/v5.x/stable-review/patch-5.1.20-rc1.gz
or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-5.1.y
and the diffstat can be found below.
thanks,
greg k-h
-------------
Pseudo-Shortlog of commits:
Greg Kroah-Hartman <[email protected]>
Linux 5.1.20-rc1
Junxiao Bi <[email protected]>
dm bufio: fix deadlock with loop device
Norbert Manthey <[email protected]>
pstore: Fix double-free in pstore_mkfile() failure path
Josua Mayer <[email protected]>
dt-bindings: allow up to four clocks for orion-mdio
Josua Mayer <[email protected]>
net: mvmdio: allow up to four clocks to be specified for orion-mdio
Tejun Heo <[email protected]>
blkcg: update blkcg_print_stat() to handle larger outputs
Tejun Heo <[email protected]>
blk-iolatency: clear use_delay when io.latency is set to zero
Peng Fan <[email protected]>
clk: imx: imx8mm: correct audio_pll2_clk to audio_pll2_out
Konstantin Khlebnikov <[email protected]>
blk-throttle: fix zero wait time for iops throttled group
Lee, Chiasheng <[email protected]>
usb: Handle USB3 remote wakeup for LPM enabled devices correctly
Matthew Wilcox (Oracle) <[email protected]>
dax: Fix missed wakeup with PMD faults
Szymon Janc <[email protected]>
Bluetooth: Add SMP workaround Microsoft Surface Precision Mouse bug
Alexander Shishkin <[email protected]>
intel_th: msu: Fix single mode with disabled IOMMU
liaoweixiong <[email protected]>
mtd: spinand: read returns badly if the last page has bitflips
Xiaolei Li <[email protected]>
mtd: rawnand: mtk: Correct low level time calculation of r/w cycle
Dan Carpenter <[email protected]>
eCryptfs: fix a couple type promotion bugs
Jorge Ramirez-Ortiz <[email protected]>
mmc: sdhci-msm: fix mutex while in spinlock
Nathan Lynch <[email protected]>
powerpc/pseries: Fix oops in hotplug memory notifier
Greg Kurz <[email protected]>
powerpc/pseries: Fix xive=off command line
Alexey Kardashevskiy <[email protected]>
powerpc/powernv: Fix stale iommu table base after VFIO
Greg Kurz <[email protected]>
powerpc/powernv/npu: Fix reference leak
Ravi Bangoria <[email protected]>
powerpc/watchpoint: Restore NV GPRs while returning from exception
Andreas Schwab <[email protected]>
powerpc/mm/32s: fix condition that is always true
Christophe Leroy <[email protected]>
powerpc/32s: fix suspend/resume when IBATs 4-7 are used
Helge Deller <[email protected]>
parisc: Fix kernel panic due invalid values in IAOQ0 or IAOQ1
Helge Deller <[email protected]>
parisc: Ensure userspace privilege for ptraced processes in regset functions
Steve Longerbeam <[email protected]>
gpu: ipu-v3: ipu-ic: Fix saturation bit offset in TPMEM
Darrick J. Wong <[email protected]>
xfs: abort unaligned nowait directio early
Nadav Amit <[email protected]>
resource: fix locking in find_next_iomem_res()
Drew Davenport <[email protected]>
include/asm-generic/bug.h: fix "cut here" for WARN_ON for __WARN_TAINT architectures
Jan Harkes <[email protected]>
coda: pass the host file in vma->vm_file on mmap
Dan Williams <[email protected]>
libnvdimm/pfn: fix fsdax-mode namespace info-block zero-fields
Aneesh Kumar K.V <[email protected]>
mm/nvdimm: add is_ioremap_addr and use that to check ioremap address
Aaron Armstrong Skomra <[email protected]>
HID: wacom: correct touch resolution x/y typo
Aaron Armstrong Skomra <[email protected]>
HID: wacom: generic: Correct pad syncing
Aaron Armstrong Skomra <[email protected]>
HID: wacom: generic: only switch the mode on devices with LEDs
Danit Goldberg <[email protected]>
IB/mlx5: Report correctly tag matching rendezvous capability
Filipe Manana <[email protected]>
Btrfs: add missing inode version, ctime and mtime updates when punching hole
Filipe Manana <[email protected]>
Btrfs: fix fsync not persisting dentry deletions due to inode evictions
Filipe Manana <[email protected]>
Btrfs: fix data loss after inode eviction, renaming it, and fsync it
Niklas Cassel <[email protected]>
PCI: qcom: Ensure that PERST is asserted for at least 100 ms
Mika Westerberg <[email protected]>
PCI: Do not poll for PME if the device is in D3cold
Dexuan Cui <[email protected]>
PCI: hv: Fix a use-after-free bug in hv_eject_device_work()
Alexander Shishkin <[email protected]>
intel_th: pci: Add Ice Lake NNPI support
Bart Van Assche <[email protected]>
RDMA/srp: Accept again source addresses that do not have a port number
Damien Le Moal <[email protected]>
block: Fix potential overflow in blk_report_zones()
Damien Le Moal <[email protected]>
block: Allow mapping of vmalloc-ed buffers
Andres Rodriguez <[email protected]>
drm/edid: parse CEA blocks embedded in DisplayID
Kim Phillips <[email protected]>
perf/x86/amd/uncore: Set the thread mask for F17h L3 PMCs
Kim Phillips <[email protected]>
perf/x86/amd/uncore: Do not set 'ThreadMask' and 'SliceMask' for non-L3 PMCs
Kan Liang <[email protected]>
perf/x86/intel: Fix spurious NMI on fixed counter
David Rientjes <[email protected]>
x86/boot: Fix memory leak in default_get_smp_config()
Soeren Moch <[email protected]>
rt2x00usb: fix rx queue hang
YueHaibing <[email protected]>
9p/virtio: Add cleanup path in p9_virtio_init
YueHaibing <[email protected]>
9p/xen: Add cleanup path in p9_trans_xen_init
Juergen Gross <[email protected]>
xen/events: fix binding user event channels to cpus
Damien Le Moal <[email protected]>
dm zoned: fix zone state management race
Daniel Jordan <[email protected]>
padata: use smp_mb in padata_reorder to avoid orphaned padata jobs
Lyude Paul <[email protected]>
drm/nouveau/i2c: Enable i2c pads & busses during preinit
Linus Walleij <[email protected]>
ARM: dts: gemini: Set DIR-685 SPI CS as active low
Masahiro Yamada <[email protected]>
kconfig: fix missing choice values in auto.conf
Vitor Soares <[email protected]>
i3c: fix i2c and i3c scl rate by bus mode
Radoslaw Burny <[email protected]>
fs/proc/proc_sysctl.c: fix the default values of i_uid/i_gid on /proc/sys inodes.
Eric W. Biederman <[email protected]>
signal: Correct namespace fixups of si_pid and si_uid
Eric W. Biederman <[email protected]>
signal/usb: Replace kill_pid_info_as_cred with kill_pid_usb_asyncio
Julien Thierry <[email protected]>
arm64: irqflags: Add condition flags to inline asm clobber list
Jon Hunter <[email protected]>
arm64: tegra: Fix AGIC register range
Like Xu <[email protected]>
KVM: x86/vPMU: refine kvm_pmu err msg when event creation failed
Michael Neuling <[email protected]>
KVM: PPC: Book3S HV: Fix CR0 setting in TM emulation
Suraj Jitindar Singh <[email protected]>
KVM: PPC: Book3S HV: Clear pending decrementer exceptions on nested guest entry
Suraj Jitindar Singh <[email protected]>
KVM: PPC: Book3S HV: Signed extend decrementer value if not using large decrementer
Wanpeng Li <[email protected]>
KVM: VMX: check CPUID before allowing read/write of IA32_XSS
Sean Christopherson <[email protected]>
KVM: VMX: Fix handling of #MC that occurs during VM-Entry
Sean Christopherson <[email protected]>
KVM: nVMX: Always sync GUEST_BNDCFGS when it comes from vmcs01
Sean Christopherson <[email protected]>
KVM: nVMX: Don't dump VMCS if virtual APIC page can't be mapped
Sakari Ailus <[email protected]>
media: videobuf2-dma-sg: Prevent size from overflowing
Sakari Ailus <[email protected]>
media: videobuf2-core: Prevent size alignment wrapping buffer size to 0
Ezequiel Garcia <[email protected]>
media: coda: Remove unbalanced and unneeded mutex unlock
Boris Brezillon <[email protected]>
media: v4l2: Test type instead of cfg->type in v4l2_ctrl_new_custom()
Luis Henriques <[email protected]>
ceph: fix end offset in truncate_inode_pages_range call
Takashi Iwai <[email protected]>
ALSA: hda/hdmi - Fix i915 reverse port/pin mapping
Takashi Iwai <[email protected]>
ALSA: hda/hdmi - Remove duplicated define
Hui Wang <[email protected]>
ALSA: hda/realtek: apply ALC891 headset fixup to one Dell machine
Kailang Yang <[email protected]>
ALSA: hda/realtek - Fixed Headphone Mic can't record on Dell platform
Takashi Iwai <[email protected]>
ALSA: hda - Don't resume forcibly i915 HDMI/DP codec
Takashi Iwai <[email protected]>
ALSA: seq: Break too long mutex context in the write loop
Xiao Ni <[email protected]>
raid5-cache: Need to do start() part job after adding journal device
Mark Brown <[email protected]>
ASoC: core: Adapt for debugfs API change
Mark Brown <[email protected]>
ASoC: dapm: Adapt for debugfs API change
Christophe Leroy <[email protected]>
lib/scatterlist: Fix mapping iterator when sg->offset is greater than PAGE_SIZE
Trond Myklebust <[email protected]>
SUNRPC: Ensure the bvecs are reset when we re-encode the RPC request
Trond Myklebust <[email protected]>
pnfs: Fix a problem where we gratuitously start doing I/O through the MDS
Trond Myklebust <[email protected]>
pnfs/flexfiles: Fix PTR_ERR() dereferences in ff_layout_track_ds_error
Max Kellermann <[email protected]>
Revert "NFS: readdirplus optimization by cache mechanism" (memleak)
Trond Myklebust <[email protected]>
NFSv4: Handle the special Linux file open access mode
Julien Thierry <[email protected]>
arm64: Fix interrupt tracing in the presence of NMIs
Dmitry Osipenko <[email protected]>
opp: Don't use IS_ERR on invalid supplies
Emmanuel Grumbach <[email protected]>
iwlwifi: mvm: clear rfkill_safe_init_done when we start the firmware
Johannes Berg <[email protected]>
iwlwifi: mvm: delay GTK setting in FW in AP mode
Emmanuel Grumbach <[email protected]>
iwlwifi: fix RF-Kill interrupt while FW load for gen2 devices
Emmanuel Grumbach <[email protected]>
iwlwifi: don't WARN when calling iwl_get_shared_mem_conf with RF-Kill
Emmanuel Grumbach <[email protected]>
iwlwifi: pcie: fix ALIVE interrupt handling for gen2 devices w/o MSI-X
Emmanuel Grumbach <[email protected]>
iwlwifi: pcie: don't service an interrupt that was masked
Oren Givon <[email protected]>
iwlwifi: add support for hr1 RF ID
Jon Hunter <[email protected]>
arm64: tegra: Update Jetson TX1 GPU regulator timings
Krzysztof Kozlowski <[email protected]>
regulator: s2mps11: Fix buck7 and buck8 wrong voltages
Krzysztof Kozlowski <[email protected]>
regulator: s2mps11: Fix ERR_PTR dereference on GPIO lookup failure
Hui Wang <[email protected]>
Input: alps - fix a mismatch between a condition check and its comment
Nick Black <[email protected]>
Input: synaptics - whitelist Lenovo T580 SMBus intertouch
Hui Wang <[email protected]>
Input: alps - don't handle ALPS cs19 trackpoint-only device
Grant Hernandez <[email protected]>
Input: gtco - bounds check collection indent level
Coly Li <[email protected]>
bcache: destroy dc->writeback_write_wq if failed to create dc->writeback_thread
Coly Li <[email protected]>
bcache: fix mistaken sysfs entry for io_error counter
Coly Li <[email protected]>
bcache: ignore read-ahead request failure on backing device
Coly Li <[email protected]>
bcache: Revert "bcache: free heap cache_set->flush_btree in bch_journal_free"
Coly Li <[email protected]>
bcache: Revert "bcache: fix high CPU occupancy during journal"
Coly Li <[email protected]>
Revert "bcache: set CACHE_SET_IO_DISABLE in bch_cached_dev_error()"
Aurelien Aptel <[email protected]>
CIFS: fix deadlock in cached root handling
Ronnie Sahlberg <[email protected]>
cifs: flush before set-info if we have writeable handles
Paulo Alcantara (SUSE) <[email protected]>
cifs: Properly handle auto disabling of serverino option
Ronnie Sahlberg <[email protected]>
cifs: fix crash in smb2_compound_op()/smb2_set_next_command()
Ronnie Sahlberg <[email protected]>
cifs: always add credits back for unsolicited PDUs
Wen Yang <[email protected]>
crypto: crypto4xx - fix a potential double free in ppc4xx_trng_probe
Cfir Cohen <[email protected]>
crypto: ccp/gcm - use const time tag comparison.
Hook, Gary <[email protected]>
crypto: ccp - memset structure fields to zero before reuse
Christian Lamparter <[email protected]>
crypto: crypto4xx - block ciphers should only accept complete blocks
Christian Lamparter <[email protected]>
crypto: crypto4xx - fix blocksize for cfb and ofb
Christian Lamparter <[email protected]>
crypto: crypto4xx - fix AES CTR blocksize value
Eric Biggers <[email protected]>
crypto: chacha20poly1305 - fix atomic sleep when using async algorithm
Elena Petrova <[email protected]>
crypto: arm64/sha2-ce - correct digest for empty data in finup
Elena Petrova <[email protected]>
crypto: arm64/sha1-ce - correct digest for empty data in finup
Hook, Gary <[email protected]>
crypto: ccp - Validate the the error value used to index error messages
Ard Biesheuvel <[email protected]>
crypto: caam - limit output IV to CBC to work around CTR mode DMA issue
Eric Biggers <[email protected]>
crypto: ghash - fix unaligned memory access in ghash_setkey()
Finn Thain <[email protected]>
scsi: mac_scsi: Fix pseudo DMA implementation, take 2
Finn Thain <[email protected]>
scsi: mac_scsi: Increase PIO/PDMA transfer length threshold
Shivasharan S <[email protected]>
scsi: megaraid_sas: Fix calculation of target ID
Benjamin Block <[email protected]>
scsi: zfcp: fix request object use-after-free in send path causing wrong traces
Benjamin Block <[email protected]>
scsi: zfcp: fix request object use-after-free in send path causing seqno errors
Damien Le Moal <[email protected]>
scsi: sd_zbc: Fix compilation warning
Ming Lei <[email protected]>
scsi: core: Fix race on creating sense cache
Finn Thain <[email protected]>
Revert "scsi: ncr5380: Increase register polling limit"
Finn Thain <[email protected]>
scsi: NCR5380: Handle PDMA failure reliably
Finn Thain <[email protected]>
scsi: NCR5380: Always re-enable reselection interrupt
Juergen Gross <[email protected]>
xen: let alloc_xenballooned_pages() fail if not enough memory free
Denis Efremov <[email protected]>
floppy: fix out-of-bounds read in copy_buffer
Denis Efremov <[email protected]>
floppy: fix invalid pointer dereference in drive_name
Denis Efremov <[email protected]>
floppy: fix out-of-bounds read in next_valid_format
Denis Efremov <[email protected]>
floppy: fix div-by-zero in setup_format_params
Andrii Nakryiko <[email protected]>
libbpf: fix another GCC8 warning for strncpy
Dennis Zhou <[email protected]>
blk-iolatency: fix STS_AGAIN handling
Colin Ian King <[email protected]>
iavf: fix dereference of null rx_buffer pointer
Huazhong Tan <[email protected]>
net: hns3: fix __QUEUE_STATE_STACK_XOFF not cleared issue
Josua Mayer <[email protected]>
net: mvmdio: defer probe of orion-mdio if a clock is not ready
Ilya Maximets <[email protected]>
xdp: fix race on generic receive path
Taehee Yoo <[email protected]>
gtp: fix use-after-free in gtp_newlink()
Taehee Yoo <[email protected]>
gtp: fix use-after-free in gtp_encap_destroy()
Taehee Yoo <[email protected]>
gtp: fix Illegal context switch in RCU read-side critical section.
Taehee Yoo <[email protected]>
gtp: fix suspicious RCU usage
csonsino <[email protected]>
Bluetooth: validate BLE connection interval updates
Taehee Yoo <[email protected]>
gtp: add missing gtp_encap_disable_sock() in gtp_encap_enable()
Dan Carpenter <[email protected]>
Bluetooth: hidp: NUL terminate a string in the compat ioctl
Matias Karhumaa <[email protected]>
Bluetooth: Check state in l2cap_disconnect_rsp
Seeteena Thoufeek <[email protected]>
perf tests: Fix record+probe_libc_inet_pton.sh for powerpc64
Shijith Thotton <[email protected]>
genirq: Update irq stats from NMI handlers
Josua Mayer <[email protected]>
Bluetooth: 6lowpan: search for destination address in all peers
João Paulo Rechi Vita <[email protected]>
Bluetooth: Add new 13d3:3501 QCA_ROME device
João Paulo Rechi Vita <[email protected]>
Bluetooth: Add new 13d3:3491 QCA_ROME device
Tomas Bortoli <[email protected]>
Bluetooth: hci_bcsp: Fix memory leak in rx_skb
Jian Shen <[email protected]>
net: hns3: enable broadcast promisc mode when initializing VF
Jiri Olsa <[email protected]>
tools: bpftool: Fix json dump crash on powerpc
Wen Yang <[email protected]>
ASoC: audio-graph-card: fix use-after-free in graph_for_each_link
Geert Uytterhoeven <[email protected]>
gpiolib: Fix references to gpiod_[gs]et_*value_cansleep() variants
Cong Wang <[email protected]>
bonding: validate ip header before check IPPROTO_IGMP
Jiri Benc <[email protected]>
selftests: bpf: fix inlines in test_lwt_seg6local
Leo Yan <[email protected]>
bpf, libbpf, smatch: Fix potential NULL pointer dereference
Andrii Nakryiko <[email protected]>
libbpf: fix GCC8 warning for strncpy
David Howells <[email protected]>
rxrpc: Fix oops in tracepoint
Phong Tran <[email protected]>
net: usb: asix: init MAC address buffers
Guilherme G. Piccoli <[email protected]>
bnx2x: Prevent ptp_task to be rescheduled indefinitely
Taehee Yoo <[email protected]>
vxlan: do not destroy fdb if register_netdevice() is failed
Andi Kleen <[email protected]>
perf stat: Fix group lookup for metric group
Andi Kleen <[email protected]>
perf stat: Don't merge events in the same PMU
Andi Kleen <[email protected]>
perf stat: Fix metrics with --no-merge
Andi Kleen <[email protected]>
perf stat: Make metric event lookup more robust
Rander Wang <[email protected]>
ALSA: hda: Fix a headphone detection issue when using SOF
Michael Chan <[email protected]>
bnxt_en: Fix statistics context reservation logic for RDMA driver.
Michael Chan <[email protected]>
bnxt_en: Disable bus master during PCI shutdown and driver unload.
Shahar S Matityahu <[email protected]>
iwlwifi: dbg: fix debug monitor stop and restart delays
He Zhe <[email protected]>
netfilter: Fix remainder of pseudo-header protocol 0
Baruch Siach <[email protected]>
bpf: fix uapi bpf_prog_info fields alignment
Andrei Otcheretianski <[email protected]>
iwlwifi: mvm: Drop large non sta frames
Dann Frazier <[email protected]>
ixgbe: Avoid NULL pointer dereference with VF on non-IPsec hw
Yonglong Liu <[email protected]>
net: hns3: add Asym Pause support to fix autoneg problem
Vedang Patel <[email protected]>
igb: clear out skb->tstamp after reading the txtime
Maxime Chevallier <[email protected]>
net: mvpp2: prs: Don't override the sign bit in SRAM parser shift
Wen Gong <[email protected]>
ath10k: destroy sdio workqueue while remove sdio module
Dundi Raviteja <[email protected]>
ath10k: Fix memory leak in qmi
Yunsheng Lin <[email protected]>
net: hns3: add some error checking in hclge_tm module
Yonglong Liu <[email protected]>
net: hns3: fix a -Wformat-nonliteral compile warning
Coly Li <[email protected]>
bcache: fix potential deadlock in cached_def_free()
Coly Li <[email protected]>
bcache: check c->gc_thread by IS_ERR_OR_NULL in cache_set_flush()
Coly Li <[email protected]>
bcache: acquire bch_register_lock later in cached_dev_free()
Coly Li <[email protected]>
bcache: check CACHE_SET_IO_DISABLE bit in bch_journal()
Coly Li <[email protected]>
bcache: check CACHE_SET_IO_DISABLE in allocator code
Eiichi Tsukata <[email protected]>
EDAC: Fix global-out-of-bounds write when setting edac_mc_poll_msec
Ahmad Masri <[email protected]>
wil6210: drop old event after wmi_call timeout
Zefir Kurtisi <[email protected]>
ath9k: correctly handle short radar pulses
Arnd Bergmann <[email protected]>
crypto: asymmetric_keys - select CRYPTO_HASH where needed
Arnd Bergmann <[email protected]>
crypto: serpent - mark __serpent_setkey_sbox noinline
Mauro S. M. Rodrigues <[email protected]>
ixgbe: Check DDM existence in transceiver before access
Jianbo Liu <[email protected]>
net/mlx5: Get vport ACL namespace by vport index
Waibel Georg <[email protected]>
gpio: Fix return value mismatch of function gpiod_get_from_of_node()
Ferdinand Blomqvist <[email protected]>
rslib: Fix handling of of caller provided syndrome
Jiong Wang <[email protected]>
bpf: fix BPF_ALU32 | BPF_ARSH on BE arches
Ferdinand Blomqvist <[email protected]>
rslib: Fix decoding of shortened codes
Nathan Chancellor <[email protected]>
xsk: Properly terminate assignment in xskq_produce_flush_desc
Felix Kaechele <[email protected]>
netfilter: ctnetlink: Fix regression in conntrack entry deletion
Marek Szyprowski <[email protected]>
clocksource/drivers/exynos_mct: Increase priority over ARM arch timer
Dmitry Osipenko <[email protected]>
clocksource/drivers/tegra: Restore base address before cleanup
Tejun Heo <[email protected]>
libata: don't request sense data on !ZAC ATA devices
Dmitry Osipenko <[email protected]>
clocksource/drivers/tegra: Release all IRQ's on request_irq() error
Amadeusz Sławiński <[email protected]>
ASoC: Intel: hdac_hdmi: Set ops to NULL on remove
Kyle Meyer <[email protected]>
perf tools: Increase MAX_NR_CPUS and MAX_CACHES
Miaoqing Pan <[email protected]>
ath10k: fix PCIE device wake up failed
Miaoqing Pan <[email protected]>
ath10k: fix fw crash by moving chip reset after napi disabled
Claire Chang <[email protected]>
ath10k: add missing error handling
Julian Anastasov <[email protected]>
ipvs: fix tinfo memory leak in start_sync_thread
Lorenzo Bianconi <[email protected]>
mt7601u: fix possible memory leak when the device is disconnected
Masahiro Yamada <[email protected]>
x86/build: Add 'set -e' to mkcapflags.sh to delete broken capflags.c
Lorenzo Bianconi <[email protected]>
mt7601u: do not schedule rx_tasklet when the device has been disconnected
Ping-Ke Shih <[email protected]>
rtlwifi: rtl8192cu: fix error handle when usb probe failed
Icenowy Zheng <[email protected]>
net: stmmac: sun8i: force select external PHY when no internal one
Hans Verkuil <[email protected]>
media: hdpvr: fix locking and a missing msleep
André Almeida <[email protected]>
media: vimc: cap: check v4l2_fill_pixfmt return value
Philipp Zabel <[email protected]>
media: coda: increment sequence offset for the last returned frame
Marco Felsch <[email protected]>
media: coda: fix last buffer handling in V4L2_ENC_CMD_STOP
Philipp Zabel <[email protected]>
media: coda: fix mpeg2 sequence number handling
Ard Biesheuvel <[email protected]>
acpi/arm64: ignore 5.1 FADTs that are reported as 5.0
Kuninori Morimoto <[email protected]>
ASoC: soc-core: call snd_soc_unbind_card() under mutex_lock;
Robert Jarzmik <[email protected]>
media: mt9m111: fix fw-node refactoring
Nathan Huckleberry <[email protected]>
timer_list: Guard procfs specific code
Miroslav Lichvar <[email protected]>
ntp: Limit TAI-UTC offset
Anders Roxell <[email protected]>
media: i2c: fix warning same module names
Marek Szyprowski <[email protected]>
media: s5p-mfc: Make additional clocks optional
Julian Anastasov <[email protected]>
ipvs: defer hook registration to avoid leaks
Arnd Bergmann <[email protected]>
ipsec: select crypto ciphers for xfrm_algo
Julien Thierry <[email protected]>
arm64: Do not enable IRQs for ct_user_exit
Minwoo Im <[email protected]>
nvme-pci: adjust irq max_vector using num_possible_cpus()
Heiner Litz <[email protected]>
lightnvm: pblk: fix freeing of merged pages
Chaitanya Kulkarni <[email protected]>
nvme-pci: set the errno on ctrl state change error
Minwoo Im <[email protected]>
nvme-pci: properly report state change failure in nvme_reset_work
Anton Eidelman <[email protected]>
nvme: fix possible io failures when removing multipathed ns
Pan Bian <[email protected]>
EDAC/sysfs: Fix memory leak when creating a csrow object
Greg KH <[email protected]>
EDAC/sysfs: Drop device references properly
Tudor Ambarus <[email protected]>
spi: fix ctrl->num_chipselect constraint
Rafael J. Wysocki <[email protected]>
ACPICA: Clear status of GPEs on first direct enable
Dennis Zhou <[email protected]>
blk-iolatency: only account submitted bios
Qian Cai <[email protected]>
x86/cacheinfo: Fix a -Wtype-limits warning
Ilias Apalodimas <[email protected]>
net: netsec: initialize tx ring on ndo_open
Mika Westerberg <[email protected]>
PCI: Add missing link delays required by the PCIe spec
Alexei Starovoitov <[email protected]>
bpf: fix callees pruning callers
Nilkanth Ahirrao <[email protected]>
ASoC: rsnd: fixup mod ID calculation in rsnd_ctu_probe_
Denis Kirjanov <[email protected]>
ipoib: correcly show a VF hardware address
Mitch Williams <[email protected]>
iavf: allow null RX descriptors
Jason Wang <[email protected]>
vhost_net: disable zerocopy by default
Arnaldo Carvalho de Melo <[email protected]>
perf evsel: Make perf_evsel__name() accept a NULL argument
Peter Zijlstra <[email protected]>
x86/atomic: Fix smp_mb__{before,after}_atomic()Geert Uytterhoeven <[email protected]>
integrity: Fix __integrity_init_keyring() section mismatch
Kan Liang <[email protected]>
perf/x86/intel/uncore: Handle invalid event coding for free-running counter
Jiri Olsa <[email protected]>
perf/x86/intel: Disable check_msr for real HW
Qian Cai <[email protected]>
sched/fair: Fix "runnable_avg_yN_inv" not used warnings
Gao Xiang <[email protected]>
sched/core: Add __sched tag for io_schedule()
Nicolas Dichtel <[email protected]>
xfrm: fix sa selector validation
Tejun Heo <[email protected]>
blkcg, writeback: dead memcgs shouldn't contribute to writeback ownership arbitration
Bob Liu <[email protected]>
block: null_blk: fix race condition for null_del_dev
Yunsheng Lin <[email protected]>
net: hns3: delay ring buffer clearing during reset
Yunsheng Lin <[email protected]>
net: hns3: fix for skb leak when doing selftest
Yunsheng Lin <[email protected]>
net: hns3: fix for dereferencing before null checking
Michal Kalderon <[email protected]>
qed: iWARP - Fix tc for MPA ll2 connection
Aaron Lewis <[email protected]>
x86/cpufeatures: Add FDP_EXCPTN_ONLY and ZERO_FCS_FDS
Waiman Long <[email protected]>
rcu: Force inlining of rcu_read_lock()
Jerome Brunet <[email protected]>
ASoC: meson: axg-tdm: fix sample clock inversion
Rajneesh Bhardwaj <[email protected]>
x86/cpu: Add Ice Lake NNPI to Intel family
Eric Biggers <[email protected]>
crypto: testmgr - add some more preemption points
Ondrej Mosnacek <[email protected]>
selinux: fix empty write to keycreate file
Marek Szyprowski <[email protected]>
media: s5p-mfc: fix reading min scratch buffer size on MFC v6/v7
Valdis Kletnieks <[email protected]>
bpf: silence warning messages in core
Young Xiao <[email protected]>
media: davinci: vpif_capture: fix memory leak in vpif_probe()
Tony Lindgren <[email protected]>
gpio: omap: Fix lost edge wake-up interrupts
Srinivas Kandagatla <[email protected]>
regmap: fix bulk writes on paged registers
Russell King <[email protected]>
gpio: omap: ensure irq is enabled before wakeup
Russell King <[email protected]>
gpio: omap: fix lack of irqstatus_raw0 for OMAP4
Eric Auger <[email protected]>
iommu: Fix a leak in iommu_insert_resv_region
Kieran Bingham <[email protected]>
media: fdp1: Support M3N and E3 platforms
Oliver Neukum <[email protected]>
media: uvcvideo: Fix access to uninitialized fields on probe error
Xingyu Chen <[email protected]>
irqchip/meson-gpio: Add support for Meson-G12A SoC
Thomas Richter <[email protected]>
perf report: Fix OOM error in TUI mode on s390
Thomas Richter <[email protected]>
perf test 6: Fix missing kvm module load for s390
Mathieu Poirier <[email protected]>
perf cs-etm: Properly set the value of 'old' and 'head' in snapshot mode
Stefano Brivio <[email protected]>
ipset: Fix memory accounting for hash types on resize
Robert Hancock <[email protected]>
net: sfp: add mutex to prevent concurrent state checks
Borislav Petkov <[email protected]>
RAS/CEC: Fix pfn insertion
Julian Wiedmann <[email protected]>
s390/qdio: handle PENDING state for QEBSM devices
Robert Hancock <[email protected]>
net: axienet: Fix race condition causing TX hang
Fabio Estevam <[email protected]>
net: fec: Do not use netdev messages too early
Antoine Tenart <[email protected]>
crypto: inside-secure - do not rely on the hardware last bit for result descriptors
Biao Huang <[email protected]>
net: stmmac: modify default value of tx-frames
Biao Huang <[email protected]>
net: stmmac: dwmac4: fix flow control issue
Jae Hyun Yoo <[email protected]>
media: aspeed: change irq to threaded irq
Jiri Olsa <[email protected]>
perf jvmti: Address gcc string overflow warning for strncpy()
Fabio Estevam <[email protected]>
media: imx7-mipi-csis: Propagate the error if clock enabling fails
Miles Chen <[email protected]>
arm64: mm: make CONFIG_ZONE_DMA32 configurable
Abhishek Goel <[email protected]>
cpupower : frequency-set -r option misses the last cpu in related cpu list
Weihang Li <[email protected]>
net: hns3: set ops to null when unregister ad_dev
Weihang Li <[email protected]>
net: hns3: add a check to pointer in error_detected and slot_reset
Kefeng Wang <[email protected]>
media: wl128x: Fix some error handling in fm_v4l2_init_video_device()
Imre Deak <[email protected]>
locking/lockdep: Fix merging of hlocks with non-zero references
Imre Deak <[email protected]>
locking/lockdep: Fix OOO unlock when hlocks need merging
Sven Eckelmann <[email protected]>
batman-adv: Fix duplicated OGMs on NETDEV_UP
David S. Miller <[email protected]>
tua6100: Avoid build warnings.
Christophe Leroy <[email protected]>
crypto: talitos - Align SEC1 accesses to 32 bits boundaries.
Christophe Leroy <[email protected]>
crypto: talitos - properly handle split ICV.
Ioana Ciornei <[email protected]>
net: phy: Check against net_device being NULL
Shailendra Verma <[email protected]>
media: staging: media: davinci_vpfe: - Fix for memory leak if decoder initialization fails.
Kefeng Wang <[email protected]>
media: saa7164: fix remove_proc_entry warning
Hans Verkuil <[email protected]>
media: mc-device.c: don't memset __user pointer contents
Arnaldo Carvalho de Melo <[email protected]>
perf annotate TUI browser: Do not use member from variable within its own initialization
Vandana BN <[email protected]>
media: usb:zr364xx:Fix KASAN:null-ptr-deref Read in zr364xx_vidioc_querycap
Eric Biggers <[email protected]>
fscrypt: clean up some BUG_ON()s in block encryption/decryption
sumitg <[email protected]>
media: v4l2-core: fix use-after-free error
Kefeng Wang <[email protected]>
media: vim2m: fix two double-free issues
Anirudh Gupta <[email protected]>
xfrm: Fix xfrm sel prefix length validation
Jeremy Sowden <[email protected]>
af_key: fix leaks in key_pol_get_resp and dump_sp.
Eric W. Biederman <[email protected]>
signal/cifs: Fix cifs_put_tcp_session to call send_sig instead of force_sig
Eric W. Biederman <[email protected]>
signal/pid_namespace: Fix reboot_pid_ns to use send_sig not force_sig
Michal Kalderon <[email protected]>
qed: Set the doorbell address correctly
Jian Shen <[email protected]>
net: hns3: initialize CPU reverse mapping
Jose Abreu <[email protected]>
net: stmmac: Prevent missing interrupts when running NAPI
Jose Abreu <[email protected]>
net: stmmac: dwmac4/5: Clear unused address entries
Jose Abreu <[email protected]>
net: stmmac: dwmac1000: Clear unused address entries
Horia Geantă <[email protected]>
crypto: caam - avoid S/G table fetching for AEAD zero-length output
Wen Yang <[email protected]>
media: venus: firmware: fix leaked of_node references
Jungo Lin <[email protected]>
media: media_device_enum_links32: clean a reserved field
Kangjie Lu <[email protected]>
media: vpss: fix a potential NULL pointer dereference
Lubomir Rintel <[email protected]>
media: marvell-ccic: fix DMA s/g desc number calculation
Akinobu Mita <[email protected]>
media: ov7740: avoid invalid framesize setting
Christophe Leroy <[email protected]>
crypto: talitos - fix skcipher failure due to wrong output IV
Daniel Gomez <[email protected]>
media: spi: IR LED: add missing of table registration
Oliver Neukum <[email protected]>
media: dvb: usb: fix use after free in dvb_usb_device_exit
Jeremy Sowden <[email protected]>
batman-adv: fix for leaked TVLV handler.
Daniel Baluta <[email protected]>
regmap: debugfs: Fix memory leak in regmap_debugfs_init
Rakesh Pillai <[email protected]>
ath10k: Fix encoding for protected management frames
Anilkumar Kolli <[email protected]>
ath: DFS JP domain W56 fixed pulse type 3 RADAR detection
Maya Erez <[email protected]>
wil6210: fix spurious interrupts in 3-msi
Wen Gong <[email protected]>
ath10k: add peer id check in ath10k_peer_find_by_id
Dan Carpenter <[email protected]>
ath6kl: add some bounds checking
Maya Erez <[email protected]>
wil6210: fix missed MISC mbox interrupt
Surabhi Vishnoi <[email protected]>
ath10k: Fix the wrong value of enums for wmi tlv stats id
Tim Schumacher <[email protected]>
ath9k: Check for errors when reading SREV register
Emil Renner Berthing <[email protected]>
spi: rockchip: turn down tx dma bursts
Surabhi Vishnoi <[email protected]>
ath10k: Do not send probe response template for mesh
Gustavo A. R. Silva <[email protected]>
wil6210: fix potential out-of-bounds read
Toke Høiland-Jørgensen <[email protected]>
ath9k: Don't trust TX status TID number when reporting airtime
Pradeep kumar Chitrapu <[email protected]>
ath10k: fix incorrect multicast/broadcast rate setting
Alagu Sankar <[email protected]>
ath10k: htt: don't use txdone_fifo with SDIO
Yingying Tang <[email protected]>
ath10k: Check tx_stats before use it
Sven Van Asbroeck <[email protected]>
dmaengine: imx-sdma: fix use-after-free on probe error path
Maurizio Lombardi <[email protected]>
scsi: iscsi: set auth_protocol back to NULL if CHAP_A value is not supported
Nathan Chancellor <[email protected]>
arm64/efi: Mark __efistub_stext_offset as an absolute symbol explicitly
Kevin Darbyshire-Bryant <[email protected]>
MIPS: fix build on non-linux hosts
Stefan Hellermann <[email protected]>
MIPS: ath79: fix ar933x uart parity mode
-------------
Diffstat:
Documentation/atomic_t.txt | 3 +
.../devicetree/bindings/net/marvell-orion-mdio.txt | 2 +-
Documentation/scheduler/sched-pelt.c | 3 +-
Makefile | 4 +-
arch/arm/boot/dts/gemini-dlink-dir-685.dts | 2 +-
arch/arm64/Kconfig | 3 +-
arch/arm64/boot/dts/nvidia/tegra210-p2180.dtsi | 3 +-
arch/arm64/boot/dts/nvidia/tegra210.dtsi | 2 +-
arch/arm64/crypto/sha1-ce-glue.c | 2 +-
arch/arm64/crypto/sha2-ce-glue.c | 2 +-
arch/arm64/include/asm/irqflags.h | 4 +-
arch/arm64/kernel/acpi.c | 10 +-
arch/arm64/kernel/entry.S | 48 ++-
arch/arm64/kernel/image.h | 6 +-
arch/arm64/kernel/irq.c | 17 +
arch/arm64/mm/init.c | 5 +-
arch/mips/boot/compressed/Makefile | 2 +
arch/mips/boot/compressed/calc_vmlinuz_load_addr.c | 2 +-
arch/mips/include/asm/mach-ath79/ar933x_uart.h | 4 +-
arch/parisc/kernel/ptrace.c | 31 +-
arch/powerpc/include/asm/pgtable.h | 14 +
arch/powerpc/kernel/exceptions-64s.S | 9 +-
arch/powerpc/kernel/prom_init.c | 16 +-
arch/powerpc/kernel/swsusp_32.S | 73 +++-
arch/powerpc/kvm/book3s_hv.c | 13 +-
arch/powerpc/kvm/book3s_hv_tm.c | 6 +-
arch/powerpc/mm/pgtable_32.c | 2 +-
arch/powerpc/platforms/powermac/sleep.S | 68 +++-
arch/powerpc/platforms/powernv/npu-dma.c | 15 +-
arch/powerpc/platforms/powernv/pci-ioda.c | 10 +
arch/powerpc/platforms/pseries/hotplug-memory.c | 3 +
arch/powerpc/sysdev/xive/spapr.c | 52 ++-
arch/x86/events/amd/uncore.c | 15 +-
arch/x86/events/intel/core.c | 16 +-
arch/x86/events/intel/uncore.h | 10 +
arch/x86/events/intel/uncore_snbep.c | 1 +
arch/x86/include/asm/atomic.h | 8 +-
arch/x86/include/asm/atomic64_64.h | 8 +-
arch/x86/include/asm/barrier.h | 4 +-
arch/x86/include/asm/cpufeatures.h | 2 +
arch/x86/include/asm/intel-family.h | 1 +
arch/x86/kernel/cpu/cacheinfo.c | 3 +-
arch/x86/kernel/cpu/mkcapflags.sh | 2 +
arch/x86/kernel/mpparse.c | 10 +-
arch/x86/kvm/pmu.c | 4 +-
arch/x86/kvm/vmx/nested.c | 16 +-
arch/x86/kvm/vmx/vmx.c | 30 +-
block/bio.c | 28 +-
block/blk-cgroup.c | 8 +-
block/blk-iolatency.c | 51 +--
block/blk-throttle.c | 9 +-
block/blk-zoned.c | 2 +-
crypto/asymmetric_keys/Kconfig | 3 +
crypto/chacha20poly1305.c | 30 +-
crypto/ghash-generic.c | 8 +-
crypto/serpent_generic.c | 8 +-
crypto/testmgr.c | 6 +
drivers/acpi/acpica/acevents.h | 3 +-
drivers/acpi/acpica/evgpe.c | 8 +-
drivers/acpi/acpica/evgpeblk.c | 2 +-
drivers/acpi/acpica/evxface.c | 2 +-
drivers/acpi/acpica/evxfgpe.c | 2 +-
drivers/ata/libata-eh.c | 8 +-
drivers/base/regmap/regmap-debugfs.c | 2 +
drivers/base/regmap/regmap.c | 2 +
drivers/block/floppy.c | 34 +-
drivers/block/null_blk_main.c | 11 +-
drivers/bluetooth/btusb.c | 2 +
drivers/bluetooth/hci_bcsp.c | 5 +
drivers/clk/imx/clk-imx8mm.c | 6 +-
drivers/clocksource/exynos_mct.c | 4 +-
drivers/clocksource/timer-tegra20.c | 7 +-
drivers/crypto/amcc/crypto4xx_alg.c | 36 +-
drivers/crypto/amcc/crypto4xx_core.c | 24 +-
drivers/crypto/amcc/crypto4xx_core.h | 10 +-
drivers/crypto/amcc/crypto4xx_trng.c | 1 -
drivers/crypto/caam/caamalg.c | 10 +-
drivers/crypto/caam/caamalg_qi.c | 2 +-
drivers/crypto/caam/caamalg_qi2.c | 9 +
drivers/crypto/caam/qi.c | 3 +
drivers/crypto/ccp/ccp-dev.c | 96 +++---
drivers/crypto/ccp/ccp-dev.h | 2 +-
drivers/crypto/ccp/ccp-ops.c | 15 +-
drivers/crypto/inside-secure/safexcel_cipher.c | 24 +-
drivers/crypto/talitos.c | 35 +-
drivers/dma/imx-sdma.c | 48 +--
drivers/edac/edac_mc_sysfs.c | 34 +-
drivers/edac/edac_module.h | 2 +-
drivers/gpio/gpio-omap.c | 29 +-
drivers/gpio/gpiolib.c | 13 +-
drivers/gpu/drm/drm_edid.c | 81 ++++-
drivers/gpu/drm/nouveau/nvkm/subdev/i2c/base.c | 20 ++
drivers/gpu/ipu-v3/ipu-ic.c | 2 +-
drivers/hid/wacom_sys.c | 3 +
drivers/hid/wacom_wac.c | 19 +-
drivers/hid/wacom_wac.h | 1 +
drivers/hwtracing/intel_th/msu.c | 2 +-
drivers/hwtracing/intel_th/pci.c | 5 +
drivers/i3c/master.c | 51 ++-
drivers/infiniband/hw/mlx5/main.c | 8 +-
drivers/infiniband/ulp/ipoib/ipoib_main.c | 1 +
drivers/infiniband/ulp/srp/ib_srp.c | 21 +-
drivers/input/mouse/alps.c | 32 ++
drivers/input/mouse/synaptics.c | 1 +
drivers/input/tablet/gtco.c | 20 +-
drivers/iommu/iommu.c | 8 +-
drivers/irqchip/irq-gic-v3.c | 7 +
drivers/irqchip/irq-meson-gpio.c | 1 +
drivers/lightnvm/pblk-core.c | 18 +-
drivers/md/bcache/alloc.c | 9 +
drivers/md/bcache/bcache.h | 2 -
drivers/md/bcache/io.c | 12 +
drivers/md/bcache/journal.c | 52 ++-
drivers/md/bcache/super.c | 25 +-
drivers/md/bcache/sysfs.c | 4 +-
drivers/md/bcache/util.h | 2 -
drivers/md/bcache/writeback.c | 5 +
drivers/md/dm-bufio.c | 4 +-
drivers/md/dm-zoned-metadata.c | 24 --
drivers/md/dm-zoned.h | 28 +-
drivers/md/raid5.c | 11 +-
drivers/media/common/videobuf2/videobuf2-core.c | 4 +
drivers/media/common/videobuf2/videobuf2-dma-sg.c | 2 +-
drivers/media/dvb-frontends/tua6100.c | 22 +-
drivers/media/i2c/Makefile | 2 +-
drivers/media/i2c/{adv7511.c => adv7511-v4l2.c} | 5 +
drivers/media/i2c/mt9m111.c | 8 +-
drivers/media/i2c/ov7740.c | 6 +-
drivers/media/media-device.c | 10 +-
drivers/media/pci/saa7164/saa7164-core.c | 33 +-
drivers/media/platform/aspeed-video.c | 5 +-
drivers/media/platform/coda/coda-bit.c | 9 +-
drivers/media/platform/coda/coda-common.c | 2 +
drivers/media/platform/davinci/vpif_capture.c | 16 +-
drivers/media/platform/davinci/vpss.c | 5 +
drivers/media/platform/marvell-ccic/mcam-core.c | 5 +-
drivers/media/platform/qcom/venus/firmware.c | 6 +-
drivers/media/platform/rcar_fdp1.c | 8 +
drivers/media/platform/s5p-mfc/s5p_mfc.c | 3 +-
drivers/media/platform/s5p-mfc/s5p_mfc_pm.c | 5 +
drivers/media/platform/vim2m.c | 6 +-
drivers/media/platform/vimc/vimc-capture.c | 5 +-
drivers/media/radio/wl128x/fmdrv_v4l2.c | 3 +
drivers/media/rc/ir-spi.c | 1 +
drivers/media/usb/dvb-usb/dvb-usb-init.c | 7 +-
drivers/media/usb/hdpvr/hdpvr-video.c | 17 +-
drivers/media/usb/uvc/uvc_ctrl.c | 4 +-
drivers/media/usb/zr364xx/zr364xx.c | 3 +-
drivers/media/v4l2-core/v4l2-ctrls.c | 27 +-
drivers/mmc/host/sdhci-msm.c | 9 +-
drivers/mtd/nand/raw/mtk_nand.c | 24 +-
drivers/mtd/nand/spi/core.c | 2 +-
drivers/net/bonding/bond_main.c | 37 +-
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c | 5 +-
.../net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c | 4 +-
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c | 33 +-
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.h | 3 +
drivers/net/ethernet/broadcom/bnxt/bnxt.c | 20 +-
drivers/net/ethernet/freescale/fec_main.c | 6 +-
drivers/net/ethernet/hisilicon/hns3/hnae3.c | 2 +
drivers/net/ethernet/hisilicon/hns3/hns3_enet.c | 146 ++++----
drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c | 6 +-
.../ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 4 +-
.../ethernet/hisilicon/hns3/hns3pf/hclge_mdio.c | 7 +
.../net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c | 6 +-
.../ethernet/hisilicon/hns3/hns3vf/hclgevf_main.c | 14 +-
drivers/net/ethernet/intel/iavf/iavf_txrx.c | 27 +-
drivers/net/ethernet/intel/igb/igb_main.c | 1 +
drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c | 3 +-
drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.c | 3 +
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h | 1 +
drivers/net/ethernet/marvell/mvmdio.c | 7 +-
drivers/net/ethernet/marvell/mvpp2/mvpp2_prs.c | 3 +-
drivers/net/ethernet/mellanox/mlx5/core/eswitch.c | 4 +-
drivers/net/ethernet/qlogic/qed/qed_dev.c | 29 +-
drivers/net/ethernet/qlogic/qed/qed_iwarp.c | 2 +
drivers/net/ethernet/qlogic/qed/qed_rdma.c | 2 +-
drivers/net/ethernet/socionext/netsec.c | 32 +-
drivers/net/ethernet/stmicro/stmmac/common.h | 2 +-
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 5 +
.../net/ethernet/stmicro/stmmac/dwmac1000_core.c | 6 +
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c | 18 +-
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 3 +
drivers/net/ethernet/xilinx/xilinx_axienet_main.c | 20 +-
drivers/net/gtp.c | 36 +-
drivers/net/phy/phy_device.c | 6 +
drivers/net/phy/sfp.c | 6 +-
drivers/net/usb/asix_devices.c | 6 +-
drivers/net/vxlan.c | 37 +-
drivers/net/wireless/ath/ath10k/debugfs_sta.c | 7 +
drivers/net/wireless/ath/ath10k/htt_rx.c | 4 +-
drivers/net/wireless/ath/ath10k/hw.c | 2 +-
drivers/net/wireless/ath/ath10k/mac.c | 14 +-
drivers/net/wireless/ath/ath10k/pci.c | 9 +-
drivers/net/wireless/ath/ath10k/qmi.c | 1 +
drivers/net/wireless/ath/ath10k/sdio.c | 7 +
drivers/net/wireless/ath/ath10k/txrx.c | 3 +
drivers/net/wireless/ath/ath10k/wmi-tlv.c | 4 +-
drivers/net/wireless/ath/ath10k/wmi.h | 7 +-
drivers/net/wireless/ath/ath6kl/wmi.c | 10 +-
drivers/net/wireless/ath/ath9k/hw.c | 32 +-
drivers/net/wireless/ath/ath9k/recv.c | 6 +-
drivers/net/wireless/ath/ath9k/xmit.c | 7 +-
drivers/net/wireless/ath/dfs_pattern_detector.c | 2 +-
drivers/net/wireless/ath/wil6210/interrupt.c | 67 ++--
drivers/net/wireless/ath/wil6210/txrx.c | 1 +
drivers/net/wireless/ath/wil6210/wmi.c | 13 +-
drivers/net/wireless/intel/iwlwifi/fw/dbg.c | 2 -
drivers/net/wireless/intel/iwlwifi/fw/dbg.h | 6 +-
drivers/net/wireless/intel/iwlwifi/fw/smem.c | 12 +-
drivers/net/wireless/intel/iwlwifi/iwl-csr.h | 1 +
drivers/net/wireless/intel/iwlwifi/mvm/fw.c | 8 +-
drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c | 53 ++-
drivers/net/wireless/intel/iwlwifi/mvm/mvm.h | 3 +
drivers/net/wireless/intel/iwlwifi/mvm/tx.c | 3 +
.../wireless/intel/iwlwifi/pcie/ctxt-info-gen3.c | 2 +-
.../net/wireless/intel/iwlwifi/pcie/ctxt-info.c | 2 +-
drivers/net/wireless/intel/iwlwifi/pcie/internal.h | 27 ++
drivers/net/wireless/intel/iwlwifi/pcie/rx.c | 66 ++--
.../net/wireless/intel/iwlwifi/pcie/trans-gen2.c | 9 +
drivers/net/wireless/intel/iwlwifi/pcie/trans.c | 8 +-
drivers/net/wireless/mediatek/mt7601u/dma.c | 54 +--
drivers/net/wireless/mediatek/mt7601u/tx.c | 4 +-
drivers/net/wireless/ralink/rt2x00/rt2x00usb.c | 12 +-
drivers/net/wireless/realtek/rtlwifi/usb.c | 5 +-
drivers/nvdimm/dax_devs.c | 2 +-
drivers/nvdimm/pfn.h | 1 +
drivers/nvdimm/pfn_devs.c | 18 +-
drivers/nvme/host/core.c | 14 +-
drivers/nvme/host/pci.c | 14 +-
drivers/opp/core.c | 2 +-
drivers/pci/controller/dwc/pcie-qcom.c | 2 +
drivers/pci/controller/pci-hyperv.c | 15 +-
drivers/pci/pci.c | 36 +-
drivers/pci/pci.h | 1 +
drivers/pci/pcie/portdrv_core.c | 66 ++++
drivers/ras/cec.c | 4 +-
drivers/regulator/da9211-regulator.c | 2 +
drivers/regulator/s2mps11.c | 9 +-
drivers/regulator/s5m8767.c | 4 +-
drivers/regulator/tps65090-regulator.c | 7 +-
drivers/s390/cio/qdio_main.c | 1 +
drivers/s390/scsi/zfcp_fsf.c | 55 ++-
drivers/scsi/NCR5380.c | 18 +-
drivers/scsi/NCR5380.h | 2 +-
drivers/scsi/mac_scsi.c | 375 ++++++++++++---------
drivers/scsi/megaraid/megaraid_sas_base.c | 3 +-
drivers/scsi/scsi_lib.c | 6 +-
drivers/scsi/sd_zbc.c | 2 +-
drivers/spi/spi-rockchip.c | 4 +-
drivers/spi/spi.c | 12 +-
drivers/staging/media/davinci_vpfe/vpfe_video.c | 3 +
drivers/staging/media/imx/imx7-mipi-csis.c | 14 +-
drivers/target/iscsi/iscsi_target_auth.c | 16 +-
drivers/usb/core/devio.c | 48 +--
drivers/usb/core/hub.c | 7 +-
drivers/vhost/net.c | 2 +-
drivers/xen/balloon.c | 16 +-
drivers/xen/events/events_base.c | 12 +-
drivers/xen/evtchn.c | 2 +-
fs/btrfs/file.c | 5 +
fs/btrfs/tree-log.c | 40 ++-
fs/ceph/file.c | 2 +-
fs/cifs/cifs_fs_sb.h | 5 +
fs/cifs/connect.c | 12 +-
fs/cifs/inode.c | 16 +
fs/cifs/misc.c | 1 +
fs/cifs/smb2inode.c | 12 +
fs/cifs/smb2ops.c | 57 +++-
fs/coda/file.c | 70 +++-
fs/crypto/crypto.c | 15 +-
fs/dax.c | 53 +--
fs/ecryptfs/crypto.c | 12 +-
fs/fs-writeback.c | 8 +-
fs/nfs/dir.c | 90 +----
fs/nfs/flexfilelayout/flexfilelayoutdev.c | 2 +-
fs/nfs/inode.c | 1 +
fs/nfs/internal.h | 3 +-
fs/nfs/nfs4file.c | 2 +-
fs/nfs/pnfs.c | 2 +-
fs/proc/proc_sysctl.c | 4 +
fs/pstore/inode.c | 13 +-
fs/xfs/xfs_file.c | 6 +-
include/asm-generic/bug.h | 6 +-
include/drm/drm_displayid.h | 10 +
include/linux/blkdev.h | 4 +-
include/linux/cpuhotplug.h | 2 +-
include/linux/mm.h | 5 +
include/linux/rcupdate.h | 2 +-
include/linux/sched/signal.h | 2 +-
include/net/ip_vs.h | 6 +-
include/net/xdp_sock.h | 2 +
include/rdma/ib_verbs.h | 4 +-
include/sound/hda_codec.h | 2 +
include/trace/events/rxrpc.h | 2 +-
include/uapi/linux/bpf.h | 1 +
include/xen/events.h | 3 +-
kernel/bpf/Makefile | 1 +
kernel/bpf/core.c | 4 +-
kernel/bpf/verifier.c | 11 +-
kernel/iomem.c | 2 +-
kernel/irq/chip.c | 4 +
kernel/irq/irqdesc.c | 16 +-
kernel/locking/lockdep.c | 59 ++--
kernel/padata.c | 12 +
kernel/pid_namespace.c | 2 +-
kernel/resource.c | 20 +-
kernel/sched/core.c | 2 +-
kernel/sched/sched-pelt.h | 2 +-
kernel/signal.c | 136 ++++++--
kernel/time/ntp.c | 4 +-
kernel/time/timer_list.c | 36 +-
lib/reed_solomon/decode_rs.c | 18 +-
lib/scatterlist.c | 9 +-
net/9p/trans_virtio.c | 8 +-
net/9p/trans_xen.c | 8 +-
net/batman-adv/bat_iv_ogm.c | 4 +-
net/batman-adv/hard-interface.c | 3 +
net/batman-adv/translation-table.c | 2 +
net/batman-adv/types.h | 3 +
net/bluetooth/6lowpan.c | 14 +-
net/bluetooth/hci_event.c | 5 +
net/bluetooth/hidp/core.c | 2 +-
net/bluetooth/hidp/sock.c | 1 +
net/bluetooth/l2cap_core.c | 15 +-
net/bluetooth/smp.c | 13 +
net/key/af_key.c | 8 +-
net/netfilter/ipset/ip_set_hash_gen.h | 2 +-
net/netfilter/ipvs/ip_vs_core.c | 21 +-
net/netfilter/ipvs/ip_vs_ctl.c | 4 -
net/netfilter/ipvs/ip_vs_sync.c | 134 ++++----
net/netfilter/nf_conntrack_netlink.c | 7 +-
net/netfilter/nf_conntrack_proto_icmp.c | 2 +-
net/netfilter/nf_nat_proto.c | 2 +-
net/netfilter/utils.c | 5 +-
net/sunrpc/clnt.c | 3 +-
net/sunrpc/xprt.c | 2 +
net/sunrpc/xprtsock.c | 1 +
net/xdp/xsk.c | 31 +-
net/xdp/xsk_queue.h | 2 +-
net/xfrm/Kconfig | 2 +
net/xfrm/xfrm_user.c | 19 ++
scripts/kconfig/confdata.c | 7 +-
scripts/kconfig/expr.h | 1 +
security/integrity/digsig.c | 5 +-
security/selinux/hooks.c | 11 +-
sound/core/seq/seq_clientmgr.c | 11 +-
sound/hda/hdac_controller.c | 5 +-
sound/pci/hda/hda_codec.c | 8 +-
sound/pci/hda/patch_hdmi.c | 31 +-
sound/pci/hda/patch_realtek.c | 10 +-
sound/soc/codecs/hdac_hdmi.c | 6 +
sound/soc/generic/audio-graph-card.c | 6 +-
sound/soc/meson/axg-tdm.h | 2 +-
sound/soc/sh/rcar/ctu.c | 2 +-
sound/soc/soc-core.c | 20 +-
sound/soc/soc-dapm.c | 18 +-
tools/bpf/bpftool/jit_disasm.c | 11 +-
tools/include/uapi/linux/bpf.h | 1 +
tools/lib/bpf/libbpf.c | 8 +-
tools/lib/bpf/xsk.c | 6 +-
tools/perf/arch/arm/util/cs-etm.c | 127 ++++++-
tools/perf/jvmti/libjvmti.c | 4 +-
tools/perf/perf.h | 2 +-
tools/perf/tests/parse-events.c | 27 ++
.../tests/shell/record+probe_libc_inet_pton.sh | 2 +-
tools/perf/ui/browsers/annotate.c | 5 +-
tools/perf/util/annotate.c | 5 +-
tools/perf/util/evsel.c | 8 +-
tools/perf/util/header.c | 2 +-
tools/perf/util/metricgroup.c | 47 ++-
tools/perf/util/stat-display.c | 3 +-
tools/perf/util/stat-shadow.c | 23 +-
tools/power/cpupower/utils/cpufreq-set.c | 2 +
.../selftests/bpf/progs/test_lwt_seg6local.c | 12 +-
375 files changed, 3753 insertions(+), 1601 deletions(-)Greg Kroah-Hartman
maintainerPATCH 1/371 MIPS: ath79: fix ar933x uart parity mode
[ Upstream commit db13a5ba2732755cf13320f3987b77cf2a71e790 ]
While trying to get the uart with parity working I found setting even parity enabled odd parity insted. Fix the register settings to match the datasheet of AR9331.
A similar patch was created by 8devices, but not sent upstream.
https://github.com/8devices/openwrt-8devices/commit/77c5586ade3bb72cda010afad3f209ed0c98ea7c
--- arch/mips/include/asm/mach-ath79/ar933x_uart.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/mips/include/asm/mach-ath79/ar933x_uart.h +2 -2
@@ -27,8 +27,8 @@#define AR933X_UART_CS_PARITY_S 0#define AR933X_UART_CS_PARITY_M 0x3#define AR933X_UART_CS_PARITY_NONE 0 -#define AR933X_UART_CS_PARITY_ODD 1 -#define AR933X_UART_CS_PARITY_EVEN 2 +#define AR933X_UART_CS_PARITY_ODD 2 +#define AR933X_UART_CS_PARITY_EVEN 3#define AR933X_UART_CS_IF_MODE_S 2#define AR933X_UART_CS_IF_MODE_M 0x3#define AR933X_UART_CS_IF_MODE_NONE 0
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 2/371 MIPS: fix build on non-linux hosts
In reply to Greg Kroah-Hartman[ Upstream commit 1196364f21ffe5d1e6d83cafd6a2edb89404a3ae ]
calc_vmlinuz_load_addr.c requires SZ_64K to be defined for alignment purposes. It included "../../../../include/linux/sizes.h" to define that size, however "sizes.h" tries to include <linux/const.h> which assumes linux system headers. These may not exist eg. the following error was encountered when building Linux for OpenWrt under macOS:
In file included from arch/mips/boot/compressed/calc_vmlinuz_load_addr.c:16:arch/mips/boot/compressed/../../../../include/linux/sizes.h:11:10: fatal error: 'linux/const.h' file not found
^~~~~~~~~~
Change makefile to force building on local linux headers instead of system headers. Also change eye-watering relative reference in include file spec.
Thanks to Jo-Philip Wich & Petr Štetiar for assistance in tracking this down & fixing.
--- arch/mips/boot/compressed/Makefile | 2 ++ arch/mips/boot/compressed/calc_vmlinuz_load_addr.c | 2 +- 2 files changed, 3 insertions(+), 1 deletion(-)
arch/mips/boot/compressed/Makefile +2 -0
@@ -78,6 +78,8 @@ OBJCOPYFLAGS_piggy.o := --add-section=.image=$(obj)/vmlinux.bin.z \ $(obj)/piggy.o: $(obj)/dummy.o $(obj)/vmlinux.bin.z FORCE $(call if_changed,objcopy) +HOSTCFLAGS_calc_vmlinuz_load_addr.o += $(LINUXINCLUDE) + # Calculate the load address of the compressed kernel image hostprogs-y := calc_vmlinuz_load_addr
arch/mips/boot/compressed/calc_vmlinuz_load_addr.c +1 -1
@@ -13,7 +13,7 @@#include <stdint.h> #include <stdio.h> #include <stdlib.h> -#include "../../../../include/linux/sizes.h" +#include <linux/sizes.h> int main (int argc,char *argv[]) {
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 3/371 arm64/efi: Mark __efistub_stext_offset as an absolute symbol explicitly
In reply to Greg Kroah-Hartman[ Upstream commit aa69fb62bea15126e744af2e02acc0d6cf3ed4da ]
After r363059 and r363928 in LLVM, a build using ld.lld as the linker with CONFIG_RANDOMIZE_BASE enabled fails like so:
ld.lld: error: relocation R_AARCH64_ABS32 cannot be used against symbol __efistub_stext_offset; recompile with -fPIC
Fangrui and Peter figured out that ld.lld is incorrectly considering __efistub_stext_offset as a relative symbol because of the order in which symbols are evaluated. _text is treated as an absolute symbol and stext is a relative symbol, making __efistub_stext_offset a relative symbol.
Adding ABSOLUTE will force ld.lld to evalute this expression in the right context and does not change ld.bfd's behavior. ld.lld will need to be fixed but the developers do not see a quick or simple fix without some research (see the linked issue for further explanation). Add this simple workaround so that ld.lld can continue to link kernels.
--- arch/arm64/kernel/image.h | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
arch/arm64/kernel/image.h +5 -1
@@ -78,7 +78,11 @@#ifdef CONFIG_EFI -__efistub_stext_offset = stext - _text; +/* +* Use ABSOLUTE() to avoid ld.lld treating this as a relative symbol: +* https://github.com/ClangBuiltLinux/linux/issues/561 +*/ +__efistub_stext_offset =ABSOLUTE (stext - _text);/* * The EFI stub has its own symbol namespace prefixed by __efistub_, to
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 4/371 scsi: iscsi: set auth_protocol back to NULL if CHAP_A value is not supported
In reply to Greg Kroah-Hartman[ Upstream commit 5dd6c49339126c2c8df2179041373222362d6e49 ]
If the CHAP_A value is not supported, the chap_server_open() function should free the auth_protocol pointer and set it to NULL, or we will leave a dangling pointer around.
[ 66.010905] Unsupported CHAP_A value [ 66.011660] Security negotiation failed. [ 66.012443] iSCSI Login negotiation failed. [ 68.413924] general protection fault: 0000 [#1] SMP PTI [ 68.414962] CPU: 0 PID: 1562 Comm: targetcli Kdump: loaded Not tainted 4.18.0-80.el8.x86_64 #1 [ 68.416589] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 [ 68.417677] RIP: 0010:__kmalloc_track_caller+0xc2/0x210
--- drivers/target/iscsi/iscsi_target_auth.c | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-)
drivers/target/iscsi/iscsi_target_auth.c +8 -8
@@ -89,6 +89,12 @@ static int chap_check_algorithm(const char *a_str)return CHAP_DIGEST_UNKNOWN ; } +static void chap_close (struct iscsi_conn *conn) +{ +kfree (conn->auth_protocol); + conn->auth_protocol =NULL ; +} + static struct iscsi_chap *chap_server_open( struct iscsi_conn *conn, struct iscsi_node_auth *auth,
@@ -126,7 +132,7 @@ static struct iscsi_chap *chap_server_open(case CHAP_DIGEST_UNKNOWN :default :pr_err ("Unsupported CHAP_A value\n" ); -kfree (conn->auth_protocol); +chap_close (conn);return NULL ; }
@@ -141,19 +147,13 @@ static struct iscsi_chap *chap_server_open(* Generate Challenge. */ if (chap_gen_challenge (conn,1 , aic_str, aic_len) <0 ) { -kfree (conn->auth_protocol); +chap_close (conn);return NULL ; }return chap; } -static void chap_close (struct iscsi_conn *conn) -{ -kfree (conn->auth_protocol); - conn->auth_protocol =NULL ; -} - static int chap_server_compute_md5( struct iscsi_conn *conn, struct iscsi_node_auth *auth,
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 5/371 dmaengine: imx-sdma: fix use-after-free on probe error path
In reply to Greg Kroah-Hartman[ Upstream commit 2b8066c3deb9140fdf258417a51479b2aeaa7622 ]
If probe() fails anywhere beyond the point where sdma_get_firmware() is called, then a kernel oops may occur.
Problematic sequence of events:
1. probe() calls sdma_get_firmware(), which schedules the firmware callback to run when firmware becomes available, using the sdma instance structure as the context
2. probe() encounters an error, which deallocates the sdma instance structure
3. firmware becomes available, firmware callback is called with deallocated sdma instance structure
4. use after free - kernel oops !
Solution: only attempt to load firmware when we're certain that probe() will succeed. This guarantees that the firmware callback's context will remain valid.
Note that the remove() path is unaffected by this issue: the firmware loader will increment the driver module's use count, ensuring that the module cannot be unloaded while the firmware callback is pending or running.
--- drivers/dma/imx-sdma.c | 48 ++++++++++++++++++++++++------------------ 1 file changed, 27 insertions(+), 21 deletions(-)
drivers/dma/imx-sdma.c +27 -21
@@ -2096,27 +2096,6 @@ static int sdma_probe(struct platform_device *pdev)if (pdata && pdata->script_addrs)sdma_add_scripts (sdma, pdata->script_addrs); -if (pdata) { - ret =sdma_get_firmware (sdma, pdata->fw_name); -if (ret) -dev_warn (&pdev->dev,"failed to get firmware from platform data\n" ); - }else { -/* -* Because that device tree does not encode ROM script address, -* the RAM script in firmware is mandatory for device tree -* probe, otherwise it fails. -*/ - ret =of_property_read_string (np,"fsl,sdma-ram-script-name" , - &fw_name); -if (ret) -dev_warn (&pdev->dev,"failed to get firmware name\n" ); -else { - ret =sdma_get_firmware (sdma, fw_name); -if (ret) -dev_warn (&pdev->dev,"failed to get firmware from device tree\n" ); - } - } - sdma->dma_device.dev = &pdev->dev; sdma->dma_device.device_alloc_chan_resources = sdma_alloc_chan_resources;
@@ -2161,6 +2140,33 @@ static int sdma_probe(struct platform_device *pdev)of_node_put (spba_bus); } +/* +* Kick off firmware loading as the very last step: +* attempt to load firmware only if we're not on the error path, because +* the firmware callback requires a fully functional and allocated sdma +* instance. +*/ +if (pdata) { + ret =sdma_get_firmware (sdma, pdata->fw_name); +if (ret) +dev_warn (&pdev->dev,"failed to get firmware from platform data\n" ); + }else { +/* +* Because that device tree does not encode ROM script address, +* the RAM script in firmware is mandatory for device tree +* probe, otherwise it fails. +*/ + ret =of_property_read_string (np,"fsl,sdma-ram-script-name" , + &fw_name); +if (ret) { +dev_warn (&pdev->dev,"failed to get firmware name\n" ); + }else { + ret =sdma_get_firmware (sdma, fw_name); +if (ret) +dev_warn (&pdev->dev,"failed to get firmware from device tree\n" ); + } + } +return 0 ; err_register:
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 6/371 ath10k: Check tx_stats before use it
In reply to Greg Kroah-Hartman[ Upstream commit 9e7251fa38978b85108c44743e1436d48e8d0d76 ]
tx_stats will be freed and set to NULL before debugfs_sta node is removed in station disconnetion process. So if read the debugfs_sta node there may be NULL pointer error. Add check for tx_stats before use it to resove this issue.
--- drivers/net/wireless/ath/ath10k/debugfs_sta.c | 7 +++++++ 1 file changed, 7 insertions(+)
drivers/net/wireless/ath/ath10k/debugfs_sta.c +7 -0
@@ -663,6 +663,13 @@ static ssize_t ath10k_dbg_sta_dump_tx_stats(struct file *file,mutex_lock (&ar->conf_mutex); +if (!arsta->tx_stats) { +ath10k_warn (ar,"failed to get tx stats" ); +mutex_unlock (&ar->conf_mutex); +kfree (buf); +return 0 ; + } +spin_lock_bh (&ar->data_lock);for (k =0 ; k <ATH10K_STATS_TYPE_MAX ; k++) {for (j =0 ; j <ATH10K_COUNTER_TYPE_MAX ; j++) {
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 7/371 ath10k: htt: dont use txdone_fifo with SDIO
In reply to Greg Kroah-Hartman[ Upstream commit e2a6b711282a371c5153239e0468a48254f17ca6 ]
HTT High Latency (ATH10K_DEV_TYPE_HL) does not use txdone_fifo at all, we don't even initialise it by skipping ath10k_htt_tx_alloc_buf() in ath10k_htt_tx_start(). Because of this using QCA6174 SDIO ath10k_htt_rx_tx_compl_ind() will crash when it accesses unitialised txdone_fifo. So skip txdone_fifo when using High Latency mode.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
--- drivers/net/wireless/ath/ath10k/htt_rx.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/net/wireless/ath/ath10k/htt_rx.c +3 -1
@@ -2277,7 +2277,9 @@ static void ath10k_htt_rx_tx_compl_ind(struct ath10k *ar,* Note that with only one concurrent reader and one concurrent * writer, you don't need extra locking to use these macro. */ -if (!kfifo_put (&htt->txdone_fifo, tx_done)) { +if (ar->bus_param.dev_type ==ATH10K_DEV_TYPE_HL ) { +ath10k_txrx_tx_unref (htt, &tx_done); + }else if (!kfifo_put (&htt->txdone_fifo, tx_done)) {ath10k_warn (ar,"txdone fifo overrun, msdu_id %d status %d\n" , tx_done.msdu_id, tx_done.status);ath10k_txrx_tx_unref (htt, &tx_done);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 8/371 ath10k: fix incorrect multicast/broadcast rate setting
In reply to Greg Kroah-Hartman[ Upstream commit 93ee3d108fc77e19efeac3ec5aa7d5886711bfef ]
Invalid rate code is sent to firmware when multicast rate value of 0 is sent to driver indicating disabled case, causing broken mesh path. so fix that.
Tested on QCA9984 with firmware 10.4-3.6.1-00827
Sven tested on IPQ4019 with 10.4-3.5.3-00057 and QCA9888 with 10.4-3.5.3-00053 (ath10k-firmware) and 10.4-3.6-00140 (linux-firmware 2018-12-16-211de167).
--- drivers/net/wireless/ath/ath10k/mac.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-)
drivers/net/wireless/ath/ath10k/mac.c +7 -3
@@ -5588,8 +5588,8 @@ static void ath10k_bss_info_changed(struct ieee80211_hw *hw,struct cfg80211_chan_def def;u32 vdev_param, pdev_param, slottime, preamble;u16 bitrate, hw_value; -u8 rate, basic_rate_idx; -int rateidx, ret =0 , hw_rate_code; +u8 rate, basic_rate_idx, rateidx; +int ret =0 , hw_rate_code, mcast_rate;enum nl80211_band band;const struct ieee80211_supported_band *sband;
@@ -5776,7 +5776,11 @@ static void ath10k_bss_info_changed(struct ieee80211_hw *hw,if (changed &BSS_CHANGED_MCAST_RATE && !ath10k_mac_vif_chan (arvif->vif, &def)) { band = def.chan->band; - rateidx = vif->bss_conf.mcast_rate[band] -1 ; + mcast_rate = vif->bss_conf.mcast_rate[band]; +if (mcast_rate >0 ) + rateidx = mcast_rate -1 ; +else + rateidx =ffs (vif->bss_conf.basic_rates) -1 ;if (ar->phy_capability &WHAL_WLAN_11A_CAPABILITY ) rateidx +=ATH10K_MAC_FIRST_OFDM_RATE_IDX ;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 9/371 ath9k: Dont trust TX status TID number when reporting airtime
In reply to Greg Kroah-Hartman[ Upstream commit 389b72e58259336c2d56d58b660b79cf4b9e0dcb ]
As already noted a comment in ath_tx_complete_aggr(), the hardware will occasionally send a TX status with the wrong tid number. If we trust the value, airtime usage will be reported to the wrong AC, which can cause the deficit on that AC to become very low, blocking subsequent attempts to transmit.
To fix this, account airtime usage to the TID number from the original skb, instead of the one in the hardware TX status report.
--- drivers/net/wireless/ath/ath9k/xmit.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/net/wireless/ath/ath9k/xmit.c +4 -3
@@ -668,7 +668,8 @@ static bool bf_is_ampdu_not_probing(struct ath_buf *bf)static void ath_tx_count_airtime (struct ath_softc *sc,struct ieee80211_sta *sta,struct ath_buf *bf, -struct ath_tx_status *ts) +struct ath_tx_status *ts, +u8 tid) {u32 airtime =0 ;int i;
@@ -679,7 +680,7 @@ static void ath_tx_count_airtime(struct ath_softc *sc, airtime += rate_dur * bf->rates[i].count; } -ieee80211_sta_register_airtime (sta, ts->tid, airtime,0 ); +ieee80211_sta_register_airtime (sta, tid, airtime,0 ); } static void ath_tx_process_buffer(struct ath_softc *sc, struct ath_txq *txq,
@@ -709,7 +710,7 @@ static void ath_tx_process_buffer(struct ath_softc *sc, struct ath_txq *txq,if (sta) {struct ath_node *an = (struct ath_node *)sta->drv_priv; tid =ath_get_skb_tid (sc, an, bf->bf_mpdu); -ath_tx_count_airtime (sc, sta, bf, ts); +ath_tx_count_airtime (sc, sta, bf, ts, tid->tidno);if (ts->ts_status & (ATH9K_TXERR_FILT |ATH9K_TXERR_XRETRY )) tid->clear_ps_filter = true; }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 10/371 wil6210: fix potential out-of-bounds read
In reply to Greg Kroah-Hartman[ Upstream commit bfabdd6997323adbedccb13a3fed1967fb8cf8f5 ]
Notice that *rc* can evaluate to up to 5, include/linux/netdevice.h:
enum gro_result {
GRO_MERGED,
GRO_MERGED_FREE,
GRO_HELD,
GRO_NORMAL,
GRO_DROP,
GRO_CONSUMED,
};
typedef enum gro_result gro_result_t;
In case *rc* evaluates to 5, we end up having an out-of-bounds read at drivers/net/wireless/ath/wil6210/txrx.c:821:
wil_dbg_txrx(wil, "Rx complete %d bytes => %s\n", len, gro_res_str[rc]);
Fix this by adding element "GRO_CONSUMED" to array gro_res_str.
Addresses-Coverity-ID: 1444666 ("Out-of-bounds read")
--- drivers/net/wireless/ath/wil6210/txrx.c | 1 + 1 file changed, 1 insertion(+)
drivers/net/wireless/ath/wil6210/txrx.c +1 -0
@@ -750,6 +750,7 @@ void wil_netif_rx_any(struct sk_buff *skb, struct net_device *ndev) [GRO_HELD] = "GRO_HELD", [GRO_NORMAL] = "GRO_NORMAL", [GRO_DROP] = "GRO_DROP", + [GRO_CONSUMED ] ="GRO_CONSUMED" , }; wil->txrx_ops.get_netif_rx_params (skb, &cid, &security);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 11/371 ath10k: Do not send probe response template for mesh
In reply to Greg Kroah-Hartman[ Upstream commit 97354f2c432788e3163134df6bb144f4b6289d87 ]
Currently mac80211 do not support probe response template for mesh point. When WMI_SERVICE_BEACON_OFFLOAD is enabled, host driver tries to configure probe response template for mesh, but it fails because the interface type is not NL80211_IFTYPE_AP but NL80211_IFTYPE_MESH_POINT.
To avoid this failure, skip sending probe response template to firmware for mesh point.
Tested HW: WCN3990/QCA6174/QCA9984
--- drivers/net/wireless/ath/ath10k/mac.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/net/wireless/ath/ath10k/mac.c +4 -0
@@ -1630,6 +1630,10 @@ static int ath10k_mac_setup_prb_tmpl(struct ath10k_vif *arvif)if (arvif->vdev_type !=WMI_VDEV_TYPE_AP )return 0 ; +/* For mesh, probe response and beacon share the same template */ +if (ieee80211_vif_is_mesh (vif)) +return 0 ; + prb =ieee80211_proberesp_get (hw, vif);if (!prb) {ath10k_warn (ar,"failed to get probe resp template from mac80211\n" );
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 12/371 spi: rockchip: turn down tx dma bursts
In reply to Greg Kroah-Hartman[ Upstream commit 47300728fb213486a830565d2af49da967c9d16a ]
This fixes tx and bi-directional dma transfers on rk3399-gru-kevin.
It seems the SPI fifo must have room for 2 bursts when the dma_tx_req signal is generated or it might skip some words. This in turn makes the rx dma channel never complete for bi-directional transfers.
Fix it by setting tx burst length to fifo_len / 4 and the dma watermark to fifo_len / 2.
However the rk3399 TRM says (sic):
"DMAC support incrementing-address burst and fixed-address burst. But in the case of access SPI and UART at byte or halfword size, DMAC only support fixed-address burst and the address must be aligned to word."
So this relies on fifo_len being a multiple of 16 such that the burst length (= fifo_len / 4) is a multiple of 4 and the addresses will be word-aligned.
--- drivers/spi/spi-rockchip.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/spi/spi-rockchip.c +2 -2
@@ -425,7 +425,7 @@ static int rockchip_spi_prepare_dma(struct rockchip_spi *rs, .direction = DMA_MEM_TO_DEV, .dst_addr = rs->dma_addr_tx, .dst_addr_width = rs->n_bytes, - .dst_maxburst = rs->fifo_len / 2, + .dst_maxburst = rs->fifo_len / 4, };dmaengine_slave_config (master->dma_tx, &txconf);
@@ -526,7 +526,7 @@ static void rockchip_spi_config(struct rockchip_spi *rs,else writel_relaxed (rs->fifo_len /2 -1 , rs->regs +ROCKCHIP_SPI_RXFTLR ); -writel_relaxed (rs->fifo_len /2 -1 , rs->regs +ROCKCHIP_SPI_DMATDLR ); +writel_relaxed (rs->fifo_len /2 , rs->regs +ROCKCHIP_SPI_DMATDLR );writel_relaxed (0 , rs->regs +ROCKCHIP_SPI_DMARDLR );writel_relaxed (dmacr, rs->regs +ROCKCHIP_SPI_DMACR );
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 13/371 ath9k: Check for errors when reading SREV register
In reply to Greg Kroah-Hartman[ Upstream commit 2f90c7e5d09437a4d8d5546feaae9f1cf48cfbe1 ]
Right now, if an error is encountered during the SREV register read (i.e. an EIO in ath9k_regread()), that error code gets passed all the way to __ath9k_hw_init(), where it is visible during the "Chip rev not supported" message.
ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
ath: phy2: Mac Chip Rev 0x0f.3 is not supported by this driver
ath: phy2: Unable to initialize hardware; initialization status: -95
ath: phy2: Unable to initialize hardware; initialization status: -95
ath9k_htc: Failed to initialize the device
Check for -EIO explicitly in ath9k_hw_read_revisions() and return a boolean based on the success of the operation. Check for that in __ath9k_hw_init() and abort with a more debugging-friendly message if reading the revisions wasn't successful.
ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
ath: phy2: Failed to read SREV register
ath: phy2: Could not read hardware revision
ath: phy2: Unable to initialize hardware; initialization status: -95
ath: phy2: Unable to initialize hardware; initialization status: -95
ath9k_htc: Failed to initialize the device
This helps when debugging by directly showing the first point of failure and it could prevent possible errors if a 0x0f.3 revision is ever supported.
--- drivers/net/wireless/ath/ath9k/hw.c | 32 +++++++++++++++++++++-------- 1 file changed, 23 insertions(+), 9 deletions(-)
drivers/net/wireless/ath/ath9k/hw.c +23 -9
@@ -252,8 +252,9 @@ void ath9k_hw_get_channel_centers(struct ath_hw *ah,/* Chip Revisions */ /******************/ -static void ath9k_hw_read_revisions (struct ath_hw *ah) +static bool ath9k_hw_read_revisions (struct ath_hw *ah) { +u32 srev;u32 val;if (ah->get_mac_revision)
@@ -269,25 +270,33 @@ static void ath9k_hw_read_revisions(struct ath_hw *ah) val =REG_READ (ah,AR_SREV ); ah->hw_version.macRev =MS (val,AR_SREV_REVISION2 ); } -return ; +return true;case AR9300_DEVID_AR9340 : ah->hw_version.macVersion =AR_SREV_VERSION_9340 ; -return ; +return true;case AR9300_DEVID_QCA955X : ah->hw_version.macVersion =AR_SREV_VERSION_9550 ; -return ; +return true;case AR9300_DEVID_AR953X : ah->hw_version.macVersion =AR_SREV_VERSION_9531 ; -return ; +return true;case AR9300_DEVID_QCA956X : ah->hw_version.macVersion =AR_SREV_VERSION_9561 ; -return ; +return true; } - val =REG_READ (ah,AR_SREV ) &AR_SREV_ID ; + srev =REG_READ (ah,AR_SREV ); + +if (srev == -EIO ) { +ath_err (ath9k_hw_common (ah), +"Failed to read SREV register" ); +return false; + } + + val = srev &AR_SREV_ID ;if (val ==0xFF ) { - val =REG_READ (ah,AR_SREV ); + val = srev; ah->hw_version.macVersion = (val &AR_SREV_VERSION2 ) >>AR_SREV_TYPE2_S ; ah->hw_version.macRev =MS (val,AR_SREV_REVISION2 );
@@ -306,6 +315,8 @@ static void ath9k_hw_read_revisions(struct ath_hw *ah)if (ah->hw_version.macVersion ==AR_SREV_VERSION_5416_PCIE ) ah->is_pciexpress = true; } + +return true; }/************************************/
@@ -559,7 +570,10 @@ static int __ath9k_hw_init(struct ath_hw *ah)struct ath_common *common =ath9k_hw_common (ah);int r =0 ; -ath9k_hw_read_revisions (ah); +if (!ath9k_hw_read_revisions (ah)) { +ath_err (common,"Could not read hardware revisions" ); +return -EOPNOTSUPP ; + }switch (ah->hw_version.macVersion) {case AR_SREV_VERSION_5416_PCI :
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 14/371 ath10k: Fix the wrong value of enums for wmi tlv stats id
In reply to Greg Kroah-Hartman[ Upstream commit 9280f4fc06f44d0b4dc9e831f72d97b3d7cd35d3 ]
The enum value for WMI_TLV_STAT_PDEV, WMI_TLV_STAT_VDEV and WMI_TLV_STAT_PEER is wrong, due to which the vdev stats are not received from firmware in wmi_update_stats event.
Fix the enum values for above stats to receive all stats from firmware in WMI_TLV_UPDATE_STATS_EVENTID.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
--- drivers/net/wireless/ath/ath10k/wmi.h | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/net/wireless/ath/ath10k/wmi.h +4 -3
@@ -4535,9 +4535,10 @@ enum wmi_10_4_stats_id { };enum wmi_tlv_stats_id { -WMI_TLV_STAT_PDEV =BIT (0 ), -WMI_TLV_STAT_VDEV =BIT (1 ), -WMI_TLV_STAT_PEER =BIT (2 ), +WMI_TLV_STAT_PEER =BIT (0 ), +WMI_TLV_STAT_AP =BIT (1 ), +WMI_TLV_STAT_PDEV =BIT (2 ), +WMI_TLV_STAT_VDEV =BIT (3 ),WMI_TLV_STAT_PEER_EXTD =BIT (10 ), };
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 15/371 wil6210: fix missed MISC mbox interrupt
In reply to Greg Kroah-Hartman[ Upstream commit 7441be71ba7e07791fd4fa2b07c932dff14ff4d9 ]
When MISC interrupt is triggered due to HALP bit, in parallel to mbox events handling by the MISC threaded IRQ, new mbox interrupt can be missed in the following scenario:
1. MISC ICR is read in the IRQ handler
2. Threaded IRQ is completed and all MISC interrupts are unmasked
3. mbox interrupt is set by FW
4. HALP is masked
The mbox interrupt in step 3 can be missed due to constant high level of ICM.
Masking all MISC IRQs instead of masking only HALP bit in step 4 will guarantee that ICM will drop to 0 and interrupt will be triggered once MISC interrupts will be unmasked.
--- drivers/net/wireless/ath/wil6210/interrupt.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/wireless/ath/wil6210/interrupt.c +1 -1
@@ -580,7 +580,7 @@ static irqreturn_t wil6210_irq_misc(int irq, void *cookie)/* no need to handle HALP ICRs until next vote */ wil->halp.handle_icr = false;wil_dbg_irq (wil,"irq_misc: HALP IRQ invoked\n" ); -wil6210_mask_halp (wil); +wil6210_mask_irq_misc (wil, true);complete (&wil->halp.comp); } }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 16/371 ath6kl: add some bounds checking
In reply to Greg Kroah-Hartman[ Upstream commit 5d6751eaff672ea77642e74e92e6c0ac7f9709ab ]
The "ev->traffic_class" and "reply->ac" variables come from the network and they're used as an offset into the wmi->stream_exist_for_ac[] array. Those variables are u8 so they can be 0-255 but the stream_exist_for_ac[] array only has WMM_NUM_AC (4) elements. We need to add a couple bounds checks to prevent array overflows.
I also modified one existing check from "if (traffic_class > 3) {" to "if (traffic_class >= WMM_NUM_AC) {" just to make them all consistent.
--- drivers/net/wireless/ath/ath6kl/wmi.c | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-)
drivers/net/wireless/ath/ath6kl/wmi.c +9 -1
@@ -1176,6 +1176,10 @@ static int ath6kl_wmi_pstream_timeout_event_rx(struct wmi *wmi, u8 *datap,return -EINVAL ; ev = (struct wmi_pstream_timeout_event *) datap; +if (ev->traffic_class >=WMM_NUM_AC ) { +ath6kl_err ("invalid traffic class: %d\n" , ev->traffic_class); +return -EINVAL ; + }/* * When the pstream (fat pipe == AC) timesout, it means there were
@@ -1517,6 +1521,10 @@ static int ath6kl_wmi_cac_event_rx(struct wmi *wmi, u8 *datap, int len,return -EINVAL ; reply = (struct wmi_cac_event *) datap; +if (reply->ac >=WMM_NUM_AC ) { +ath6kl_err ("invalid AC: %d\n" , reply->ac); +return -EINVAL ; + }if ((reply->cac_indication ==CAC_INDICATION_ADMISSION_RESP ) && (reply->status_code !=IEEE80211_TSPEC_STATUS_ADMISS_ACCEPTED )) {
@@ -2633,7 +2641,7 @@ int ath6kl_wmi_delete_pstream_cmd(struct wmi *wmi, u8 if_idx, u8 traffic_class,u16 active_tsids =0 ;int ret; -if (traffic_class >3 ) { +if (traffic_class >=WMM_NUM_AC ) {ath6kl_err ("invalid traffic class: %d\n" , traffic_class);return -EINVAL ; }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 17/371 ath10k: add peer id check in ath10k_peer_find_by_id
In reply to Greg Kroah-Hartman[ Upstream commit 49ed34b835e231aa941257394716bc689bc98d9f ]
For some SDIO chip, the peer id is 65535 for MPDU with error status, then test_bit will trigger buffer overflow for peer's memory, if kasan enabled, it will report error.
Reason is when station is in disconnecting status, firmware do not delete the peer info since it not disconnected completely, meanwhile some AP will still send data packet to station, then hardware will receive the packet and send to firmware, firmware's logic will report peer id of 65535 for MPDU with error status.
Add check for overflow the size of peer's peer_ids will avoid the buffer overflow access.
Call trace of kasan:
dump_backtrace+0x0/0x2ec show_stack+0x20/0x2c __dump_stack+0x20/0x28 dump_stack+0xc8/0xec print_address_description+0x74/0x240 kasan_report+0x250/0x26c __asan_report_load8_noabort+0x20/0x2c ath10k_peer_find_by_id+0x180/0x1e4 [ath10k_core] ath10k_htt_t2h_msg_handler+0x100c/0x2fd4 [ath10k_core] ath10k_htt_htc_t2h_msg_handler+0x20/0x34 [ath10k_core] ath10k_sdio_irq_handler+0xcc8/0x1678 [ath10k_sdio] process_sdio_pending_irqs+0xec/0x370 sdio_run_irqs+0x68/0xe4 sdio_irq_work+0x1c/0x28 process_one_work+0x3d8/0x8b0 worker_thread+0x508/0x7cc kthread+0x24c/0x264 ret_from_fork+0x10/0x18
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
--- drivers/net/wireless/ath/ath10k/txrx.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/net/wireless/ath/ath10k/txrx.c +3 -0
@@ -150,6 +150,9 @@ struct ath10k_peer *ath10k_peer_find_by_id(struct ath10k *ar, int peer_id) {struct ath10k_peer *peer; +if (peer_id >=BITS_PER_TYPE (peer->peer_ids)) +return NULL ; +lockdep_assert_held (&ar->data_lock);list_for_each_entry (peer, &ar->peers, list)
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 18/371 wil6210: fix spurious interrupts in 3-msi
In reply to Greg Kroah-Hartman[ Upstream commit e10b0eddd5235aa5aef4e40b970e34e735611a80 ]
Interrupt is set in ICM (ICR & ~IMV) rising trigger. As the driver masks the IRQ after clearing it, there can be a race where an additional spurious interrupt is triggered when the driver unmask the IRQ.
This can happen in case HW triggers an interrupt after the clear and before the mask.
To prevent the second spurious interrupt the driver needs to mask the IRQ before reading and clearing it.
--- drivers/net/wireless/ath/wil6210/interrupt.c | 65 ++++++++++++-------- 1 file changed, 40 insertions(+), 25 deletions(-)
drivers/net/wireless/ath/wil6210/interrupt.c +40 -25
@@ -296,21 +296,24 @@ void wil_configure_interrupt_moderation(struct wil6210_priv *wil)static irqreturn_t wil6210_irq_rx (int irq,void *cookie) {struct wil6210_priv *wil = cookie; -u32 isr =wil_ioread32_and_clear (wil->csr + -HOSTADDR (RGF_DMA_EP_RX_ICR ) + - offsetof(struct RGF_ICR , ICR)); +u32 isr;bool need_unmask = true; +wil6210_mask_irq_rx (wil); + + isr =wil_ioread32_and_clear (wil->csr + +HOSTADDR (RGF_DMA_EP_RX_ICR ) + + offsetof(struct RGF_ICR , ICR)); +trace_wil6210_irq_rx (isr);wil_dbg_irq (wil,"ISR RX 0x%08x\n" , isr);if (unlikely (!isr)) {wil_err_ratelimited (wil,"spurious IRQ: RX\n" ); +wil6210_unmask_irq_rx (wil);return IRQ_NONE ; } -wil6210_mask_irq_rx (wil); -/* RX_DONE and RX_HTRSH interrupts are the same if interrupt * moderation is not used. Interrupt moderation may cause RX * buffer overflow while RX_DONE is delayed. The required
@@ -355,21 +358,24 @@ static irqreturn_t wil6210_irq_rx(int irq, void *cookie)static irqreturn_t wil6210_irq_rx_edma (int irq,void *cookie) {struct wil6210_priv *wil = cookie; -u32 isr =wil_ioread32_and_clear (wil->csr + -HOSTADDR (RGF_INT_GEN_RX_ICR ) + - offsetof(struct RGF_ICR , ICR)); +u32 isr;bool need_unmask = true; +wil6210_mask_irq_rx_edma (wil); + + isr =wil_ioread32_and_clear (wil->csr + +HOSTADDR (RGF_INT_GEN_RX_ICR ) + + offsetof(struct RGF_ICR , ICR)); +trace_wil6210_irq_rx (isr);wil_dbg_irq (wil,"ISR RX 0x%08x\n" , isr);if (unlikely (!isr)) {wil_err (wil,"spurious IRQ: RX\n" ); +wil6210_unmask_irq_rx_edma (wil);return IRQ_NONE ; } -wil6210_mask_irq_rx_edma (wil); -if (likely (isr &BIT_RX_STATUS_IRQ )) {wil_dbg_irq (wil,"RX status ring\n" ); isr &= ~BIT_RX_STATUS_IRQ ;
@@ -403,21 +409,24 @@ static irqreturn_t wil6210_irq_rx_edma(int irq, void *cookie)static irqreturn_t wil6210_irq_tx_edma (int irq,void *cookie) {struct wil6210_priv *wil = cookie; -u32 isr =wil_ioread32_and_clear (wil->csr + -HOSTADDR (RGF_INT_GEN_TX_ICR ) + - offsetof(struct RGF_ICR , ICR)); +u32 isr;bool need_unmask = true; +wil6210_mask_irq_tx_edma (wil); + + isr =wil_ioread32_and_clear (wil->csr + +HOSTADDR (RGF_INT_GEN_TX_ICR ) + + offsetof(struct RGF_ICR , ICR)); +trace_wil6210_irq_tx (isr);wil_dbg_irq (wil,"ISR TX 0x%08x\n" , isr);if (unlikely (!isr)) {wil_err (wil,"spurious IRQ: TX\n" ); +wil6210_unmask_irq_tx_edma (wil);return IRQ_NONE ; } -wil6210_mask_irq_tx_edma (wil); -if (likely (isr &BIT_TX_STATUS_IRQ )) {wil_dbg_irq (wil,"TX status ring\n" ); isr &= ~BIT_TX_STATUS_IRQ ;
@@ -446,21 +455,24 @@ static irqreturn_t wil6210_irq_tx_edma(int irq, void *cookie)static irqreturn_t wil6210_irq_tx (int irq,void *cookie) {struct wil6210_priv *wil = cookie; -u32 isr =wil_ioread32_and_clear (wil->csr + -HOSTADDR (RGF_DMA_EP_TX_ICR ) + - offsetof(struct RGF_ICR , ICR)); +u32 isr;bool need_unmask = true; +wil6210_mask_irq_tx (wil); + + isr =wil_ioread32_and_clear (wil->csr + +HOSTADDR (RGF_DMA_EP_TX_ICR ) + + offsetof(struct RGF_ICR , ICR)); +trace_wil6210_irq_tx (isr);wil_dbg_irq (wil,"ISR TX 0x%08x\n" , isr);if (unlikely (!isr)) {wil_err_ratelimited (wil,"spurious IRQ: TX\n" ); +wil6210_unmask_irq_tx (wil);return IRQ_NONE ; } -wil6210_mask_irq_tx (wil); -if (likely (isr &BIT_DMA_EP_TX_ICR_TX_DONE )) {wil_dbg_irq (wil,"TX done\n" ); isr &= ~BIT_DMA_EP_TX_ICR_TX_DONE ;
@@ -532,20 +544,23 @@ static bool wil_validate_mbox_regs(struct wil6210_priv *wil)static irqreturn_t wil6210_irq_misc (int irq,void *cookie) {struct wil6210_priv *wil = cookie; -u32 isr =wil_ioread32_and_clear (wil->csr + -HOSTADDR (RGF_DMA_EP_MISC_ICR ) + - offsetof(struct RGF_ICR , ICR)); +u32 isr; + +wil6210_mask_irq_misc (wil, false); + + isr =wil_ioread32_and_clear (wil->csr + +HOSTADDR (RGF_DMA_EP_MISC_ICR ) + + offsetof(struct RGF_ICR , ICR));trace_wil6210_irq_misc (isr);wil_dbg_irq (wil,"ISR MISC 0x%08x\n" , isr);if (!isr) {wil_err (wil,"spurious IRQ: MISC\n" ); +wil6210_unmask_irq_misc (wil, false);return IRQ_NONE ; } -wil6210_mask_irq_misc (wil, false); -if (isr &ISR_MISC_FW_ERROR ) {u32 fw_assert_code =wil_r (wil, wil->rgf_fw_assert_code_addr); u32 ucode_assert_code =
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 19/371 ath: DFS JP domain W56 fixed pulse type 3 RADAR detection
In reply to Greg Kroah-Hartman[ Upstream commit d8792393a783158cbb2c39939cb897dc5e5299b6 ]
Increase pulse width range from 1-2usec to 0-4usec.
During data traffic HW occasionally fails detecting radar pulses, so that SW cannot get enough radar reports to achieve the success rate.
Tested ath10k hw and fw:
* QCA9888(10.4-3.5.1-00052)
* QCA4019(10.4-3.2.1.1-00017)
* QCA9984(10.4-3.6-00104)
* QCA988X(10.2.4-1.0-00041)
Tested ath9k hw: AR9300
--- drivers/net/wireless/ath/dfs_pattern_detector.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/wireless/ath/dfs_pattern_detector.c +1 -1
@@ -111,7 +111,7 @@ static const struct radar_detector_specs jp_radar_ref_types[] = {JP_PATTERN (0 ,0 ,1 ,1428 ,1428 ,1 ,18 ,29 , false),JP_PATTERN (1 ,2 ,3 ,3846 ,3846 ,1 ,18 ,29 , false),JP_PATTERN (2 ,0 ,1 ,1388 ,1388 ,1 ,18 ,50 , false), -JP_PATTERN (3 ,1 ,2 ,4000 ,4000 ,1 ,18 ,50 , false), +JP_PATTERN (3 ,0 ,4 ,4000 ,4000 ,1 ,18 ,50 , false),JP_PATTERN (4 ,0 ,5 ,150 ,230 ,1 ,23 ,50 , false),JP_PATTERN (5 ,6 ,10 ,200 ,500 ,1 ,16 ,50 , false), JP_PATTERN(6, 11, 20, 200, 500, 1, 12, 50, false),
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 20/371 ath10k: Fix encoding for protected management frames
In reply to Greg Kroah-Hartman[ Upstream commit 42f1bc43e6a97b9ddbe976eba9bd05306c990c75 ]
Currently the protected management frames are
not appended with the MIC_LEN which results in
the protected management frames being encoded
incorrectly.
Add the extra space at the end of the protected
management frames to fix this encoding error for
the protected management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
--- drivers/net/wireless/ath/ath10k/wmi-tlv.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/net/wireless/ath/ath10k/wmi-tlv.c +3 -1
@@ -2840,8 +2840,10 @@ ath10k_wmi_tlv_op_gen_mgmt_tx_send(struct ath10k *ar, struct sk_buff *msdu,if ((ieee80211_is_action (hdr->frame_control) ||ieee80211_is_deauth (hdr->frame_control) ||ieee80211_is_disassoc (hdr->frame_control)) && -ieee80211_has_protected (hdr->frame_control)) +ieee80211_has_protected (hdr->frame_control)) { +skb_put (msdu,IEEE80211_CCMP_MIC_LEN ); buf_len +=IEEE80211_CCMP_MIC_LEN ; + } buf_len =min_t (u32, buf_len,WMI_TLV_MGMT_TX_FRAME_MAX_LEN ); buf_len =round_up (buf_len,4 );
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 21/371 regmap: debugfs: Fix memory leak in regmap_debugfs_init
In reply to Greg Kroah-Hartman[ Upstream commit 2899872b627e99b7586fe3b6c9f861da1b4d5072 ]
As detected by kmemleak running on i.MX6ULL board:
nreferenced object 0xd8366600 (size 64):
comm "swapper/0", pid 1, jiffies 4294937370 (age 933.220s) hex dump (first 32 bytes):
64 75 6d 6d 79 2d 69 6f 6d 75 78 63 2d 67 70 72 dummy-iomuxc-gpr
40 32 30 65 34 30 30 30 00 e3 f3 ab fe d1 1b dd @20e4000........
backtrace:
[<b0402aec>] kasprintf+0x2c/0x54
[<a6fbad2c>] regmap_debugfs_init+0x7c/0x31c
[<9c8d91fa>] __regmap_init+0xb5c/0xcf4
[<5b1c3d2a>] of_syscon_register+0x164/0x2c4
[<596a5d80>] syscon_node_to_regmap+0x64/0x90
[<49bd597b>] imx6ul_init_machine+0x34/0xa0
[<250a4dac>] customize_machine+0x1c/0x30
[<2d19fdaf>] do_one_initcall+0x7c/0x398
[<e6084469>] kernel_init_freeable+0x328/0x448
[<168c9101>] kernel_init+0x8/0x114
[<913268aa>] ret_from_fork+0x14/0x20
[<ce7b131a>] 0x0Root cause is that map->debugfs_name is allocated using kasprintf and then the pointer is lost by assigning it other memory address.
--- drivers/base/regmap/regmap-debugfs.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/base/regmap/regmap-debugfs.c +2 -0
@@ -565,6 +565,8 @@ void regmap_debugfs_init(struct regmap *map, const char *name) }if (!strcmp (name,"dummy" )) { +kfree (map->debugfs_name); + map->debugfs_name =kasprintf (GFP_KERNEL ,"dummy%d" , dummy_index); name = map->debugfs_name;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 22/371 batman-adv: fix for leaked TVLV handler.
In reply to Greg Kroah-Hartman[ Upstream commit 17f78dd1bd624a4dd78ed5db3284a63ee807fcc3 ]
A handler for BATADV_TVLV_ROAM was being registered when the translation-table was initialized, but not unregistered when the translation-table was freed. Unregister it.
--- net/batman-adv/translation-table.c | 2 ++ 1 file changed, 2 insertions(+)
net/batman-adv/translation-table.c +2 -0
@@ -3826,6 +3826,8 @@ static void batadv_tt_purge(struct work_struct *work)*/ void batadv_tt_free (struct batadv_priv *bat_priv) { +batadv_tvlv_handler_unregister (bat_priv,BATADV_TVLV_ROAM ,1 ); +batadv_tvlv_container_unregister (bat_priv,BATADV_TVLV_TT ,1 );batadv_tvlv_handler_unregister (bat_priv,BATADV_TVLV_TT ,1 );
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 23/371 media: dvb: usb: fix use after free in dvb_usb_device_exit
In reply to Greg Kroah-Hartman[ Upstream commit 6cf97230cd5f36b7665099083272595c55d72be7 ]
dvb_usb_device_exit() frees and uses the device name in that order. Fix by storing the name in a buffer before freeing it.
--- drivers/media/usb/dvb-usb/dvb-usb-init.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/media/usb/dvb-usb/dvb-usb-init.c +5 -2
@@ -287,12 +287,15 @@ EXPORT_SYMBOL(dvb_usb_device_init);void dvb_usb_device_exit (struct usb_interface *intf) {struct dvb_usb_device *d =usb_get_intfdata (intf); -const char *name ="generic DVB-USB module" ; +const char *default_name ="generic DVB-USB module" ; +char name[40 ];usb_set_intfdata (intf,NULL );if (d !=NULL && d->desc !=NULL ) { - name = d->desc->name; +strscpy (name, d->desc->name,sizeof (name));dvb_usb_exit (d); + }else { +strscpy (name, default_name,sizeof (name)); }info ("%s successfully deinitialized and disconnected." , name);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 24/371 media: spi: IR LED: add missing of table registration
In reply to Greg Kroah-Hartman[ Upstream commit 24e4cf770371df6ad49ed873f21618d9878f64c8 ]
MODULE_DEVICE_TABLE(of, <of_match_table> should be called to complete DT OF mathing mechanism and register it.
Before this patch:
modinfo drivers/media/rc/ir-spi.ko | grep alias
After this patch:
modinfo drivers/media/rc/ir-spi.ko | grep alias
alias: of:N*T*Cir-spi-ledC* alias: of:N*T*Cir-spi-led
--- drivers/media/rc/ir-spi.c | 1 + 1 file changed, 1 insertion(+)
drivers/media/rc/ir-spi.c +1 -0
@@ -161,6 +161,7 @@ static const struct of_device_id ir_spi_of_match[] = { { .compatible = "ir-spi-led" }, {}, }; +MODULE_DEVICE_TABLE (of, ir_spi_of_match);static struct spi_driver ir_spi_driver = { .probe = ir_spi_probe,
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 25/371 crypto: talitos - fix skcipher failure due to wrong output IV
In reply to Greg Kroah-Hartman[ Upstream commit 3e03e792865ae48b8cfc69a0b4d65f02f467389f ]
Selftests report the following:
[ 2.984845] alg: skcipher: cbc-aes-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place" [ 2.995377] 00000000: 3d af ba 42 9d 9e b4 30 b4 22 da 80 2c 9f ac 41 [ 3.032673] alg: skcipher: cbc-des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place" [ 3.043185] 00000000: fe dc ba 98 76 54 32 10 [ 3.063238] alg: skcipher: cbc-3des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place" [ 3.073818] 00000000: 7d 33 88 93 0f 93 b2 42
This above dumps show that the actual output IV is indeed the input IV. This is due to the IV not being copied back into the request.
This patch fixes that.
--- drivers/crypto/talitos.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/crypto/talitos.c +4 -0
@@ -1553,11 +1553,15 @@ static void ablkcipher_done(struct device *dev, int err) {struct ablkcipher_request *areq = context; +struct crypto_ablkcipher *cipher =crypto_ablkcipher_reqtfm (areq); +struct talitos_ctx *ctx =crypto_ablkcipher_ctx (cipher); +unsigned int ivsize =crypto_ablkcipher_ivsize (cipher);struct talitos_edesc *edesc; edesc = container_of(desc, struct talitos_edesc, desc);common_nonsnoop_unmap (dev, edesc, areq); +memcpy (areq->info, ctx->iv, ivsize);kfree (edesc);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 26/371 media: ov7740: avoid invalid framesize setting
In reply to Greg Kroah-Hartman[ Upstream commit 6e4ab830ac6d6a0d7cd7f87dc5d6536369bf24a8 ]
If the requested framesize by VIDIOC_SUBDEV_S_FMT is larger than supported framesizes, it causes an out of bounds array access and the resulting framesize is unexpected.
Avoid out of bounds array access and select the default framesize.
--- drivers/media/i2c/ov7740.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/media/i2c/ov7740.c +5 -1
@@ -761,7 +761,11 @@ static int ov7740_try_fmt_internal(struct v4l2_subdev *sd, fsize++; } - +if (i >=ARRAY_SIZE (ov7740_framesizes)) { + fsize = &ov7740_framesizes[0 ]; + fmt->width = fsize->width; + fmt->height = fsize->height; + }if (ret_frmsize !=NULL ) *ret_frmsize = fsize;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 27/371 media: marvell-ccic: fix DMA s/g desc number calculation
In reply to Greg Kroah-Hartman[ Upstream commit 0c7aa32966dab0b8a7424e1b34c7f206817953ec ]
The commit d790b7eda953 ("[media] vb2-dma-sg: move dma_(un)map_sg here") left dma_desc_nent unset. It previously contained the number of DMA descriptors as returned from dma_map_sg().
We can now (since the commit referred to above) obtain the same value from the sg_table and drop dma_desc_nent altogether.
Tested on OLPC XO-1.75 machine. Doesn't affect the OLPC XO-1's Cafe driver, since that one doesn't do DMA.
[[email protected]: fix a checkpatch warning]
--- drivers/media/platform/marvell-ccic/mcam-core.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/media/platform/marvell-ccic/mcam-core.c +3 -2
@@ -200,7 +200,6 @@ struct mcam_vb_buffer {struct list_head queue;struct mcam_dma_desc *dma_desc;/* Descriptor virtual address */ dma_addr_t dma_desc_pa;/* Descriptor physical address */ -int dma_desc_nent;/* Number of mapped descriptors */ };static inline struct mcam_vb_buffer *vb_to_mvb (struct vb2_v4l2_buffer *vb)
@@ -608,9 +607,11 @@ static void mcam_dma_contig_done(struct mcam_camera *cam, int frame)static void mcam_sg_next_buffer (struct mcam_camera *cam) {struct mcam_vb_buffer *buf; +struct sg_table *sg_table; buf = list_first_entry(&cam->buffers, struct mcam_vb_buffer, queue);list_del_init (&buf->queue); + sg_table =vb2_dma_sg_plane_desc (&buf->vb_buf.vb2_buf,0 );/* * Very Bad Not Good Things happen if you don't clear * C1_DESC_ENA before making any descriptor changes.
@@ -618,7 +619,7 @@ static void mcam_sg_next_buffer(struct mcam_camera *cam)mcam_reg_clear_bit (cam,REG_CTRL1 ,C1_DESC_ENA );mcam_reg_write (cam,REG_DMA_DESC_Y , buf->dma_desc_pa);mcam_reg_write (cam,REG_DESC_LEN_Y , - buf->dma_desc_nent*sizeof (struct mcam_dma_desc )); + sg_table->nents *sizeof (struct mcam_dma_desc ));mcam_reg_write (cam,REG_DESC_LEN_U ,0 );mcam_reg_write (cam,REG_DESC_LEN_V ,0 );mcam_reg_set_bit (cam,REG_CTRL1 ,C1_DESC_ENA );
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 28/371 media: vpss: fix a potential NULL pointer dereference
In reply to Greg Kroah-Hartman[ Upstream commit e08f0761234def47961d3252eac09ccedfe4c6a0 ]
In case ioremap fails, the fix returns -ENOMEM to avoid NULL pointer dereference.
--- drivers/media/platform/davinci/vpss.c | 5 +++++ 1 file changed, 5 insertions(+)
drivers/media/platform/davinci/vpss.c +5 -0
@@ -518,6 +518,11 @@ static int __init vpss_init(void)return -EBUSY ; oper_cfg.vpss_regs_base2 =ioremap (VPSS_CLK_CTRL ,4 ); +if (unlikely (!oper_cfg.vpss_regs_base2)) { +release_mem_region (VPSS_CLK_CTRL ,4 ); +return -ENOMEM ; + } +writel (VPSS_CLK_CTRL_VENCCLKEN |VPSS_CLK_CTRL_DACCLKEN , oper_cfg.vpss_regs_base2);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 29/371 media: media_device_enum_links32: clean a reserved field
In reply to Greg Kroah-Hartman[ Upstream commit f49308878d7202e07d8761238e01bd0e5fce2750 ]
In v4l2-compliance utility, test MEDIA_IOC_ENUM_ENTITIES will check whether reserved field of media_links_enum filled with zero.
However, for 32 bit program, the reserved field is missing copy from kernel space to user space in media_device_enum_links32 function.
This patch adds the cleaning a reserved field logic in media_device_enum_links32 function.
--- drivers/media/media-device.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)
drivers/media/media-device.c +8 -1
@@ -502,6 +502,7 @@ static long media_device_enum_links32(struct media_device *mdev, {struct media_links_enum links;compat_uptr_t pads_ptr, links_ptr; +int ret;memset (&links,0 ,sizeof (links));
@@ -513,7 +514,13 @@ static long media_device_enum_links32(struct media_device *mdev, links.pads =compat_ptr (pads_ptr); links.links =compat_ptr (links_ptr); -return media_device_enum_links (mdev, &links); + ret =media_device_enum_links (mdev, &links); +if (ret) +return ret; + +memset (ulinks->reserved,0 ,sizeof (ulinks->reserved)); + +return 0 ; }#define MEDIA_IOC_ENUM_LINKS32 _IOWR('|', 0x02, struct media_links_enum32)
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 30/371 media: venus: firmware: fix leaked of_node references
In reply to Greg Kroah-Hartman[ Upstream commit 2c41cc0be07b5ee2f1167f41cd8a86fc5b53d82c ]
The call to of_parse_phandle returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage.
Detected by coccinelle with the following warnings:
drivers/media/platform/qcom/venus/firmware.c:90:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 82, but without a corresponding object release within this function. drivers/media/platform/qcom/venus/firmware.c:94:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 82, but without a corresponding object release within this function. drivers/media/platform/qcom/venus/firmware.c:128:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 82, but without a corresponding object release within this function.
--- drivers/media/platform/qcom/venus/firmware.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/media/platform/qcom/venus/firmware.c +4 -2
@@ -87,11 +87,11 @@ static int venus_load_fw(struct venus_core *core, const char *fwname, ret =of_address_to_resource (node,0 , &r);if (ret) -return ret; + goto err_put_node; ret =request_firmware (&mdt, fwname, dev);if (ret <0 ) -return ret; + goto err_put_node; fw_size =qcom_mdt_get_size (mdt);if (fw_size <0 ) {
@@ -125,6 +125,8 @@ static int venus_load_fw(struct venus_core *core, const char *fwname,memunmap (mem_va); err_release_fw:release_firmware (mdt); +err_put_node: +of_node_put (node);return ret; }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 31/371 crypto: caam - avoid S/G table fetching for AEAD zero-length output
In reply to Greg Kroah-Hartman[ Upstream commit dcd9c76e5a183af4f793beb5141efcd260b8d09f ]
When enabling IOMMU support, the following issue becomes visible in the AEAD zero-length case.
Even though the output sequence length is set to zero, the crypto engine tries to prefetch 4 S/G table entries (since SGF bit is set in SEQ OUT PTR command - which is either generated in SW in case of caam/jr or in HW in case of caam/qi, caam/qi2).
The DMA read operation will trigger an IOMMU fault since the address in the SEQ OUT PTR is "dummy" (set to zero / not obtained via DMA API mapping).
1. In case of caam/jr, avoid the IOMMU fault by clearing the SGF bit in SEQ OUT PTR command.
2. In case of caam/qi - setting address, bpid, length to zero for output entry in the compound frame has a special meaning (cf. CAAM RM):
"Output frame = Unspecified, Input address = Y. A unspecified frame is indicated by an unused SGT entry (an entry in which the Address, Length, and BPID fields are all zero). SEC obtains output buffers from BMan as prescribed by the preheader."
Since no output buffers are needed, modify the preheader by setting (ABS = 1, ADDBUF = 0):
-"ABS = 1 means obtain the number of buffers in ADDBUF (0 or 1) from the pool POOL ID"
-ADDBUF: "If ABS is set, ADD BUF specifies whether to allocate a buffer or not"
3. In case of caam/qi2, since engine:
-does not support FLE[FMT]=2'b11 ("unused" entry) mentioned in DPAA2 RM -requires output entry to be present, even if not used
the solution chosen is to leave output frame list entry zeroized.
--- drivers/crypto/caam/caamalg.c | 1 + drivers/crypto/caam/caamalg_qi.c | 2 +- drivers/crypto/caam/caamalg_qi2.c | 9 +++++++++ drivers/crypto/caam/qi.c | 3 +++ 4 files changed, 14 insertions(+), 1 deletion(-)
drivers/crypto/caam/caamalg.c +1 -0
@@ -1072,6 +1072,7 @@ static void init_aead_job(struct aead_request *req,if (unlikely (req->src != req->dst)) {if (!edesc->mapped_dst_nents) { dst_dma =0 ; + out_options =0 ; }else if (edesc->mapped_dst_nents ==1 ) { dst_dma =sg_dma_address (req->dst); out_options =0 ;
drivers/crypto/caam/caamalg_qi.c +1 -1
@@ -1068,7 +1068,7 @@ static struct aead_edesc *aead_edesc_alloc(struct aead_request *req,dma_to_qm_sg_one_ext (&fd_sgt[0 ], qm_sg_dma + (1 + !!ivsize) *sizeof (*sg_table), out_len,0 ); - }else if (mapped_dst_nents ==1 ) { + }else if (mapped_dst_nents <=1 ) {dma_to_qm_sg_one (&fd_sgt[0 ],sg_dma_address (req->dst), out_len,0 ); }else {
drivers/crypto/caam/caamalg_qi2.c +9 -0
@@ -525,6 +525,14 @@ static struct aead_edesc *aead_edesc_alloc(struct aead_request *req,dpaa2_fl_set_addr (out_fle, qm_sg_dma + (1 + !!ivsize) *sizeof (*sg_table)); } + }else if (!mapped_dst_nents) { +/* +* crypto engine requires the output entry to be present when +* "frame list" FD is used. +* Since engine does not support FMT=2'b11 (unused entry type), +* leaving out_fle zeroized is the best option. +*/ + goto skip_out_fle; }else if (mapped_dst_nents ==1 ) {dpaa2_fl_set_format (out_fle, dpaa2_fl_single);dpaa2_fl_set_addr (out_fle,sg_dma_address (req->dst));
@@ -536,6 +544,7 @@ static struct aead_edesc *aead_edesc_alloc(struct aead_request *req,dpaa2_fl_set_len (out_fle, out_len); +skip_out_fle:return edesc; }
drivers/crypto/caam/qi.c +3 -0
@@ -18,6 +18,7 @@#include "desc_constr.h" #define PREHDR_RSLS_SHIFT 31 +#define PREHDR_ABS BIT(25)/* * Use a reasonable backlog of frames (per CPU) as congestion threshold,
@@ -346,6 +347,7 @@ int caam_drv_ctx_update(struct caam_drv_ctx *drv_ctx, u32 *sh_desc)*/ drv_ctx->prehdr[0 ] =cpu_to_caam32 ((1 <<PREHDR_RSLS_SHIFT ) | num_words); + drv_ctx->prehdr[1 ] =cpu_to_caam32 (PREHDR_ABS );memcpy (drv_ctx->sh_desc, sh_desc,desc_bytes (sh_desc)); dma_sync_single_for_device(qidev, drv_ctx->context_a, sizeof(drv_ctx->sh_desc) +
@@ -401,6 +403,7 @@ struct caam_drv_ctx *caam_drv_ctx_init(struct device *qidev,*/ drv_ctx->prehdr[0 ] =cpu_to_caam32 ((1 <<PREHDR_RSLS_SHIFT ) | num_words); + drv_ctx->prehdr[1 ] =cpu_to_caam32 (PREHDR_ABS );memcpy (drv_ctx->sh_desc, sh_desc,desc_bytes (sh_desc)); size =sizeof (drv_ctx->prehdr) +sizeof (drv_ctx->sh_desc); hwdesc = dma_map_single(qidev, drv_ctx->prehdr, size,
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 32/371 net: stmmac: dwmac1000: Clear unused address entries
In reply to Greg Kroah-Hartman[ Upstream commit 9463c445590091202659cdfdd44b236acadfbd84 ]
In case we don't use a given address entry we need to clear it because it could contain previous values that are no longer valid.
Found out while running stmmac selftests.
--- drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c | 6 ++++++ 1 file changed, 6 insertions(+)
drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c +6 -0
@@ -216,6 +216,12 @@ static void dwmac1000_set_filter(struct mac_device_info *hw, GMAC_ADDR_LOW(reg)); reg++; } + +while (reg <= perfect_addr_number) { +writel (0 , ioaddr +GMAC_ADDR_HIGH (reg)); +writel (0 , ioaddr +GMAC_ADDR_LOW (reg)); + reg++; + } }#ifdef FRAME_FILTER_DEBUG
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 33/371 net: stmmac: dwmac4/5: Clear unused address entries
In reply to Greg Kroah-Hartman[ Upstream commit 0620ec6c62a5a07625b65f699adc5d1b90394ee6 ]
In case we don't use a given address entry we need to clear it because it could contain previous values that are no longer valid.
Found out while running stmmac selftests.
--- drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c +8 -2
@@ -444,14 +444,20 @@ static void dwmac4_set_filter(struct mac_device_info *hw,* are required */ value |=GMAC_PACKET_FILTER_PR ; - }else if (!netdev_uc_empty (dev)) { -int reg =1 ; + }else {struct netdev_hw_addr *ha; +int reg =1 ;netdev_for_each_uc_addr (ha, dev) {dwmac4_set_umac_addr (hw, ha->addr, reg); reg++; } + +while (reg <=GMAC_MAX_PERFECT_ADDRESSES ) { +writel (0 , ioaddr +GMAC_ADDR_HIGH (reg)); +writel (0 , ioaddr +GMAC_ADDR_LOW (reg)); + reg++; + } }writel (value, ioaddr +GMAC_PACKET_FILTER );
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 34/371 net: stmmac: Prevent missing interrupts when running NAPI
In reply to Greg Kroah-Hartman[ Upstream commit a976ca79e23f13bff79c14e7266cea4a0ea51e67 ]
When we trigger NAPI we are disabling interrupts but in case we receive or send a packet in the meantime, as interrupts are disabled, we will miss this event.
Trigger both NAPI instances (RX and TX) when at least one event happens so that we don't miss any interrupts.
--- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +3 -0
@@ -2058,6 +2058,9 @@ static int stmmac_napi_check(struct stmmac_priv *priv, u32 chan) &priv->xstats, chan);struct stmmac_channel *ch = &priv->channel[chan]; +if (status) + status |= handle_rx | handle_tx; +if ((status & handle_rx) && (chan < priv->plat->rx_queues_to_use)) {stmmac_disable_dma_irq (priv, priv->ioaddr, chan);napi_schedule_irqoff (&ch->rx_napi);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 35/371 net: hns3: initialize CPU reverse mapping
In reply to Greg Kroah-Hartman[ Upstream commit ffab9691bcb2fe2594f4c38bfceb4d9685b93b87 ]
Allocate CPU rmap and add entry for each irq. CPU rmap is used in aRFS to get the queue number of the rx completion interrupts.
In additional, remove the calling of irq_set_affinity_notifier() in hns3_nic_init_irq(), because we have registered notifier in irq_cpu_rmap_add() for each vector, otherwise it may cause use-after-free issue.
--- .../net/ethernet/hisilicon/hns3/hns3_enet.c | 77 ++++++++++++------- 1 file changed, 48 insertions(+), 29 deletions(-)
drivers/net/ethernet/hisilicon/hns3/hns3_enet.c +48 -29
@@ -4,6 +4,9 @@#include <linux/dma-mapping.h> #include <linux/etherdevice.h> #include <linux/interrupt.h> +#ifdef CONFIG_RFS_ACCEL +#include <linux/cpu_rmap.h> +#endif #include <linux/if_vlan.h> #include <linux/ip.h> #include <linux/ipv6.h>
@@ -72,23 +75,6 @@ static irqreturn_t hns3_irq_handle(int irq, void *vector)return IRQ_HANDLED ; } -/* This callback function is used to set affinity changes to the irq affinity -* masks when the irq_set_affinity_notifier function is used. -*/ -static void hns3_nic_irq_affinity_notify (struct irq_affinity_notify *notify, -const cpumask_t *mask) -{ -struct hns3_enet_tqp_vector *tqp_vectors = - container_of(notify, struct hns3_enet_tqp_vector, - affinity_notify); - - tqp_vectors->affinity_mask = *mask; -} - -static void hns3_nic_irq_affinity_release (struct kref *ref) -{ -} -static void hns3_nic_uninit_irq (struct hns3_nic_priv *priv) {struct hns3_enet_tqp_vector *tqp_vectors;
@@ -100,8 +86,7 @@ static void hns3_nic_uninit_irq(struct hns3_nic_priv *priv)if (tqp_vectors->irq_init_flag !=HNS3_VECTOR_INITED )continue ; -/* clear the affinity notifier and affinity mask */ -irq_set_affinity_notifier (tqp_vectors->vector_irq,NULL ); +/* clear the affinity mask */ irq_set_affinity_hint (tqp_vectors->vector_irq,NULL );/* release the irq resource */
@@ -154,12 +139,6 @@ static int hns3_nic_init_irq(struct hns3_nic_priv *priv)return ret; } - tqp_vectors->affinity_notify.notify = - hns3_nic_irq_affinity_notify; - tqp_vectors->affinity_notify.release = - hns3_nic_irq_affinity_release; -irq_set_affinity_notifier (tqp_vectors->vector_irq, - &tqp_vectors->affinity_notify);irq_set_affinity_hint (tqp_vectors->vector_irq, &tqp_vectors->affinity_mask);
@@ -333,6 +312,40 @@ static void hns3_tqp_disable(struct hnae3_queue *tqp)hns3_write_dev (tqp,HNS3_RING_EN_REG , rcb_reg); } +static void hns3_free_rx_cpu_rmap (struct net_device *netdev) +{ +#ifdef CONFIG_RFS_ACCEL +free_irq_cpu_rmap (netdev->rx_cpu_rmap); + netdev->rx_cpu_rmap =NULL ; +#endif +} + +static int hns3_set_rx_cpu_rmap (struct net_device *netdev) +{ +#ifdef CONFIG_RFS_ACCEL +struct hns3_nic_priv *priv =netdev_priv (netdev); +struct hns3_enet_tqp_vector *tqp_vector; +int i, ret; + +if (!netdev->rx_cpu_rmap) { + netdev->rx_cpu_rmap =alloc_irq_cpu_rmap (priv->vector_num); +if (!netdev->rx_cpu_rmap) +return -ENOMEM ; + } + +for (i =0 ; i < priv->vector_num; i++) { + tqp_vector = &priv->tqp_vector[i]; + ret =irq_cpu_rmap_add (netdev->rx_cpu_rmap, + tqp_vector->vector_irq); +if (ret) { +hns3_free_rx_cpu_rmap (netdev); +return ret; + } + } +#endif +return 0 ; +} +static int hns3_nic_net_up (struct net_device *netdev) {struct hns3_nic_priv *priv =netdev_priv (netdev);
@@ -344,11 +357,16 @@ static int hns3_nic_net_up(struct net_device *netdev)if (ret)return ret; +/* the device can work without cpu rmap, only aRFS needs it */ + ret =hns3_set_rx_cpu_rmap (netdev); +if (ret) +netdev_warn (netdev,"set rx cpu rmap fail, ret=%d!\n" , ret); +/* get irq resource for all vectors */ ret =hns3_nic_init_irq (priv);if (ret) {netdev_err (netdev,"hns init irq failed! ret=%d\n" , ret); -return ret; + goto free_rmap; }clear_bit (HNS3_NIC_STATE_DOWN , &priv->state);
@@ -377,7 +395,8 @@ static int hns3_nic_net_up(struct net_device *netdev)hns3_vector_disable (&priv->tqp_vector[j]);hns3_nic_uninit_irq (priv); - +free_rmap: +hns3_free_rx_cpu_rmap (netdev);return ret; }
@@ -460,6 +479,8 @@ static void hns3_nic_net_down(struct net_device *netdev)if (ops->stop) ops->stop (priv->ae_handle); +hns3_free_rx_cpu_rmap (netdev); +/* free irq resources */ hns3_nic_uninit_irq (priv);
@@ -3198,8 +3219,6 @@ static void hns3_nic_uninit_vector_data(struct hns3_nic_priv *priv)hns3_free_vector_ring_chain (tqp_vector, &vector_ring_chain);if (tqp_vector->irq_init_flag ==HNS3_VECTOR_INITED ) { -irq_set_affinity_notifier (tqp_vector->vector_irq, -NULL );irq_set_affinity_hint (tqp_vector->vector_irq,NULL );free_irq (tqp_vector->vector_irq, tqp_vector); tqp_vector->irq_init_flag =HNS3_VECTOR_NOT_INITED ;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 36/371 qed: Set the doorbell address correctly
In reply to Greg Kroah-Hartman[ Upstream commit 8366d520019f366fabd6c7a13032bdcd837e18d4 ]
In 100g mode the doorbell bar is united for both engines. Set the correct offset in the hwfn so that the doorbell returned for RoCE is in the affined hwfn.
--- drivers/net/ethernet/qlogic/qed/qed_dev.c | 29 ++++++++++++++-------- drivers/net/ethernet/qlogic/qed/qed_rdma.c | 2 +- 2 files changed, 19 insertions(+), 12 deletions(-)
drivers/net/ethernet/qlogic/qed/qed_dev.c +18 -11
@@ -3441,6 +3441,7 @@ static void qed_nvm_info_free(struct qed_hwfn *p_hwfn)static int qed_hw_prepare_single (struct qed_hwfn *p_hwfn,void __iomem *p_regview,void __iomem *p_doorbells, +u64 db_phys_addr,enum qed_pci_personality personality) {struct qed_dev *cdev = p_hwfn->cdev;
@@ -3449,6 +3450,7 @@ static int qed_hw_prepare_single(struct qed_hwfn *p_hwfn,/* Split PCI bars evenly between hwfns */ p_hwfn->regview = p_regview; p_hwfn->doorbells = p_doorbells; + p_hwfn->db_phys_addr = db_phys_addr;if (IS_VF (p_hwfn->cdev))return qed_vf_hw_prepare (p_hwfn);
@@ -3544,7 +3546,9 @@ int qed_hw_prepare(struct qed_dev *cdev,/* Initialize the first hwfn - will learn number of hwfns */ rc =qed_hw_prepare_single (p_hwfn, cdev->regview, - cdev->doorbells, personality); + cdev->doorbells, + cdev->db_phys_addr, + personality);if (rc)return rc;
@@ -3553,22 +3557,25 @@ int qed_hw_prepare(struct qed_dev *cdev,/* Initialize the rest of the hwfns */ if (cdev->num_hwfns >1 ) {void __iomem *p_regview, *p_doorbell; -u8 __iomem *addr; +u64 db_phys_addr; +u32 offset;/* adjust bar offset for second engine */ - addr = cdev->regview + -qed_hw_bar_size (p_hwfn, p_hwfn->p_main_ptt, -BAR_ID_0 ) /2 ; - p_regview = addr; + offset =qed_hw_bar_size (p_hwfn, p_hwfn->p_main_ptt, +BAR_ID_0 ) /2 ; + p_regview = cdev->regview + offset; - addr = cdev->doorbells + -qed_hw_bar_size (p_hwfn, p_hwfn->p_main_ptt, -BAR_ID_1 ) /2 ; - p_doorbell = addr; + offset =qed_hw_bar_size (p_hwfn, p_hwfn->p_main_ptt, +BAR_ID_1 ) /2 ; + + p_doorbell = cdev->doorbells + offset; + + db_phys_addr = cdev->db_phys_addr + offset;/* prepare second hw function */ rc =qed_hw_prepare_single (&cdev->hwfns[1 ], p_regview, - p_doorbell, personality); + p_doorbell, db_phys_addr, + personality);/* in case of error, need to free the previously * initiliazed hwfn 0.
drivers/net/ethernet/qlogic/qed/qed_rdma.c +1 -1
@@ -803,7 +803,7 @@ static int qed_rdma_add_user(void *rdma_cxt, dpi_start_offset + ((out_params->dpi) * p_hwfn->dpi_size)); - out_params->dpi_phys_addr = p_hwfn->cdev->db_phys_addr + + out_params->dpi_phys_addr = p_hwfn->db_phys_addr + dpi_start_offset + ((out_params->dpi) * p_hwfn->dpi_size);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 37/371 signal/pid_namespace: Fix reboot_pid_ns to use send_sig not force_sig
In reply to Greg Kroah-Hartman[ Upstream commit f9070dc94542093fd516ae4ccea17ef46a4362c5 ]
The locking in force_sig_info is not prepared to deal with a task that exits or execs (as sighand may change). The is not a locking problem in force_sig as force_sig is only built to handle synchronous exceptions.
Further the function force_sig_info changes the signal state if the signal is ignored, or blocked or if SIGNAL_UNKILLABLE will prevent the delivery of the signal. The signal SIGKILL can not be ignored and can not be blocked and SIGNAL_UNKILLABLE won't prevent it from being delivered.
So using force_sig rather than send_sig for SIGKILL is confusing and pointless.
Because it won't impact the sending of the signal and and because using force_sig is wrong, replace force_sig with send_sig.
--- kernel/pid_namespace.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
kernel/pid_namespace.c +1 -1
@@ -325,7 +325,7 @@ int reboot_pid_ns(struct pid_namespace *pid_ns, int cmd) }read_lock (&tasklist_lock); -force_sig (SIGKILL , pid_ns->child_reaper); +send_sig (SIGKILL , pid_ns->child_reaper,1 );read_unlock (&tasklist_lock);do_exit (0 );
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 38/371 signal/cifs: Fix cifs_put_tcp_session to call send_sig instead of force_sig
In reply to Greg Kroah-Hartman[ Upstream commit 72abe3bcf0911d69b46c1e8bdb5612675e0ac42c ]
The locking in force_sig_info is not prepared to deal with a task that exits or execs (as sighand may change). The is not a locking problem in force_sig as force_sig is only built to handle synchronous exceptions.
Further the function force_sig_info changes the signal state if the signal is ignored, or blocked or if SIGNAL_UNKILLABLE will prevent the delivery of the signal. The signal SIGKILL can not be ignored and can not be blocked and SIGNAL_UNKILLABLE won't prevent it from being delivered.
So using force_sig rather than send_sig for SIGKILL is confusing and pointless.
Because it won't impact the sending of the signal and and because using force_sig is wrong, replace force_sig with send_sig.
--- fs/cifs/connect.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
fs/cifs/connect.c +1 -1
@@ -2625,7 +2625,7 @@ cifs_put_tcp_session(struct TCP_Server_Info *server, int from_reconnect) task =xchg (&server->tsk,NULL );if (task) -force_sig (SIGKILL , task); +send_sig (SIGKILL , task,1 ); } static struct TCP_Server_Info *
Signature · 1 line
2.20.1
Re: [PATCH 5.1 038/371] signal/cifs: Fix cifs_put_tcp_session to call send_sig instead of force_sig
Note that this patch causes a regression (removing cifs module fails, due to unmount leaking a thread with this change).
We are testing a workaround to cifs.ko which would be needed if this patch were to be backported.
Quoted 49 lines · Greg Kroah-Hartman
[ Upstream commit
72abe3bcf0911d69b46c1e8bdb5612675e0ac42c]The locking in
force_sig_infois not prepared to deal with a task that exits or execs (as sighand may change). The is not a locking problem inforce_sigasforce_sigis only built to handle synchronous exceptions.Further the function
force_sig_infochanges the signal state if the signal is ignored, or blocked or ifSIGNAL_UNKILLABLEwill prevent the delivery of the signal. The signal SIGKILL can not be ignored and can not be blocked andSIGNAL_UNKILLABLEwon't prevent it from being delivered.So using
force_sigrather thansend_sigfor SIGKILL is confusing and pointless.Because it won't impact the sending of the signal and and because using
force_sigis wrong, replaceforce_sigwithsend_sig.Cc Namjae Jeon <[email protected]>Cc Jeff Layton <[email protected]>Cc Steve French <[email protected]>Fixes a5c3e1c725af ("Revert "cifs: No need to send SIGKILL to demux_thread during umount"")Fixes e7ddee9037e7 ("cifs: disable sharing session and tcon and add new TCP sharing code")Signed-off-by "Eric W. Biederman" <[email protected]>Signed-off-by Sasha Levin <[email protected]>--- fs/cifs/connect.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)fs/cifs/connect.c +1
-2@@ -2625,7 +2625,7 @@ cifs_put_tcp_session(struct TCP_Server_Info *server, int from_reconnect) task =xchg (&server->tsk,NULL );if (task) -force_sig (SIGKILL , task); +send_sig (SIGKILL , task,1 ); } static struct TCP_Server_Info * --2.20.1
Signature · 3 lines
Thanks, Steve
Greg Kroah-Hartman
maintainerPATCH 39/371 af_key: fix leaks in key_pol_get_resp and dump_sp.
In reply to Greg Kroah-Hartman[ Upstream commit 7c80eb1c7e2b8420477fbc998971d62a648035d9 ]
In both functions, if pfkey_xfrm_policy2msg failed we leaked the newly allocated sk_buff. Free it on error.
--- net/key/af_key.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)
net/key/af_key.c +6 -2
@@ -2442,8 +2442,10 @@ static int key_pol_get_resp(struct sock *sk, struct xfrm_policy *xp, const struc goto out; } err =pfkey_xfrm_policy2msg (out_skb, xp, dir); -if (err <0 ) +if (err <0 ) { +kfree_skb (out_skb); goto out; + } out_hdr = (struct sadb_msg *) out_skb->data; out_hdr->sadb_msg_version = hdr->sadb_msg_version;
@@ -2694,8 +2696,10 @@ static int dump_sp(struct xfrm_policy *xp, int dir, int count, void *ptr)return PTR_ERR (out_skb); err =pfkey_xfrm_policy2msg (out_skb, xp, dir); -if (err <0 ) +if (err <0 ) { +kfree_skb (out_skb);return err; + } out_hdr = (struct sadb_msg *) out_skb->data; out_hdr->sadb_msg_version = pfk->dump.msg_version;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 40/371 xfrm: Fix xfrm sel prefix length validation
In reply to Greg Kroah-Hartman[ Upstream commit b38ff4075a80b4da5cb2202d7965332ca0efb213 ]
Family of src/dst can be different from family of selector src/dst. Use xfrm selector family to validate address prefix length, while verifying new sa from userspace.
Validated patch with this command:
ip xfrm state add src 1.1.6.1 dst 1.1.6.2 proto esp spi 4260196 \
reqid 20004 mode tunnel aead "rfc4106(gcm(aes))" \0x1111016400000000000000000000000044440001 128 \
sel src 1011:1:4::2/128 sel dst 1021:1:4::2/128 dev Port5
--- net/xfrm/xfrm_user.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)
net/xfrm/xfrm_user.c +16 -0
@@ -150,6 +150,22 @@ static int verify_newsa_info(struct xfrm_usersa_info *p, err = -EINVAL ;switch (p->family) { +case AF_INET : +break ; + +case AF_INET6 : +#if IS_ENABLED (CONFIG_IPV6 ) +break ; +#else + err = -EAFNOSUPPORT ; + goto out; +#endif + +default : + goto out; + } + +switch (p->sel.family) {case AF_INET :if (p->sel.prefixlen_d >32 || p->sel.prefixlen_s >32 ) goto out;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 41/371 media: vim2m: fix two double-free issues
In reply to Greg Kroah-Hartman[ Upstream commit 20059cbbf981ca954be56f7963ae494d18e2dda1 ]
vim2m_device_release() will be called by video_unregister_device() to release various objects.
There are two double-free issue,
1. dev->m2m_dev will be freed twice in error_m2m path/vim2m_device_release
2. the error_v4l2 and error_free path in vim2m_probe() will release same objects, since vim2m_device_release has done.
--- drivers/media/platform/vim2m.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/media/platform/vim2m.c +3 -3
@@ -1355,7 +1355,7 @@ static int vim2m_probe(struct platform_device *pdev) MEDIA_ENT_F_PROC_VIDEO_SCALER);if (ret) {v4l2_err (&dev->v4l2_dev,"Failed to init mem2mem media controller\n" ); - goto error_m2m; + goto error_dev; } ret =media_device_register (&dev->mdev);
@@ -1369,11 +1369,11 @@ static int vim2m_probe(struct platform_device *pdev)#ifdef CONFIG_MEDIA_CONTROLLER error_m2m_mc:v4l2_m2m_unregister_media_controller (dev->m2m_dev); -error_m2m: -v4l2_m2m_release (dev->m2m_dev);#endif error_dev:video_unregister_device (&dev->vfd); +/* vim2m_device_release called by video_unregister_device to release various objects */ +return ret; error_v4l2:v4l2_device_unregister (&dev->v4l2_dev); error_free:
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 42/371 media: v4l2-core: fix use-after-free error
In reply to Greg Kroah-Hartman[ Upstream commit 3e0f724346e96daae7792262c6767449795ac3b5 ]
Fixing use-after-free within __v4l2_ctrl_handler_setup(). Memory is being freed with kfree(new_ref) for duplicate control reference entry but ctrl->cluster pointer is still referring to freed duplicate entry resulting in error on access. Change done to update cluster pointer only when new control reference is added.
==================================================================
BUG: KASAN: use-after-free in __v4l2_ctrl_handler_setup+0x388/0x428
Read of size 8 at addr ffffffc324e78618 by task systemd-udevd/312
Allocated by task 312:
Freed by task 312:
The buggy address belongs to the object at ffffffc324e78600
which belongs to the cache kmalloc-64 of size 64
The buggy address is located 24 bytes inside of
64-byte region [ffffffc324e78600, ffffffc324e78640)
The buggy address belongs to the page:
page:ffffffbf0c939e00 count:1 mapcount:0 mapping:
(null) index:0xffffffc324e78f80
flags: 0x4000000000000100(slab)
raw: 4000000000000100 0000000000000000 ffffffc324e78f80 000000018020001a
raw: 0000000000000000 0000000100000001 ffffffc37040fb80 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffffffc324e78500: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffffffc324e78580: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffffffc324e78600: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
^
ffffffc324e78680: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc
ffffffc324e78700: 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc
==================================================================--- drivers/media/v4l2-core/v4l2-ctrls.c | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-)
drivers/media/v4l2-core/v4l2-ctrls.c +9 -9
@@ -2148,15 +2148,6 @@ static int handler_new_ref(struct v4l2_ctrl_handler *hdl,if (size_extra_req) new_ref->p_req.p = &new_ref[1 ]; -if (ctrl->handler == hdl) { -/* By default each control starts in a cluster of its own. -new_ref->ctrl is basically a cluster array with one -element, so that's perfect to use as the cluster pointer. -But only do this for the handler that owns the control. */ - ctrl->cluster = &new_ref->ctrl; - ctrl->ncontrols =1 ; - } -INIT_LIST_HEAD (&new_ref->node);mutex_lock (hdl->lock);
@@ -2189,6 +2180,15 @@ static int handler_new_ref(struct v4l2_ctrl_handler *hdl, hdl->buckets[bucket] = new_ref;if (ctrl_ref) *ctrl_ref = new_ref; +if (ctrl->handler == hdl) { +/* By default each control starts in a cluster of its own. +* new_ref->ctrl is basically a cluster array with one +* element, so that's perfect to use as the cluster pointer. +* But only do this for the handler that owns the control. +*/ + ctrl->cluster = &new_ref->ctrl; + ctrl->ncontrols =1 ; + } unlock:mutex_unlock (hdl->lock);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 43/371 fscrypt: clean up some BUG_ON()s in block encryption/decryption
In reply to Greg Kroah-Hartman[ Upstream commit eeacfdc68a104967162dfcba60f53f6f5b62a334 ]
Replace some BUG_ON()s with WARN_ON_ONCE() and returning an error code, and move the check for len divisible by FS_CRYPTO_BLOCK_SIZE into fscrypt_crypt_block() so that it's done for both encryption and decryption, not just encryption.
--- fs/crypto/crypto.c | 15 +++++++++------ 1 file changed, 9 insertions(+), 6 deletions(-)
fs/crypto/crypto.c +9 -6
@@ -159,7 +159,10 @@ int fscrypt_do_page_crypto(const struct inode *inode, fscrypt_direction_t rw,struct crypto_skcipher *tfm = ci->ci_ctfm;int res =0 ; -BUG_ON (len ==0 ); +if (WARN_ON_ONCE (len <=0 )) +return -EINVAL ; +if (WARN_ON_ONCE (len %FS_CRYPTO_BLOCK_SIZE !=0 )) +return -EINVAL ;fscrypt_generate_iv (&iv, lblk_num, ci);
@@ -243,8 +246,6 @@ struct page *fscrypt_encrypt_page(const struct inode *inode,struct page *ciphertext_page = page;int err; -BUG_ON (len %FS_CRYPTO_BLOCK_SIZE !=0 ); -if (inode->i_sb->s_cop->flags &FS_CFLG_OWN_PAGES ) {/* with inplace-encryption we just encrypt the page */ err = fscrypt_do_page_crypto(inode, FS_ENCRYPT, lblk_num, page,
@@ -256,7 +257,8 @@ struct page *fscrypt_encrypt_page(const struct inode *inode,return ciphertext_page; } -BUG_ON (!PageLocked (page)); +if (WARN_ON_ONCE (!PageLocked (page))) +return ERR_PTR (-EINVAL ); ctx =fscrypt_get_ctx (inode, gfp_flags);if (IS_ERR (ctx))
@@ -304,8 +306,9 @@ EXPORT_SYMBOL(fscrypt_encrypt_page);int fscrypt_decrypt_page (const struct inode *inode,struct page *page,unsigned int len,unsigned int offs,u64 lblk_num) { -if (!(inode->i_sb->s_cop->flags &FS_CFLG_OWN_PAGES )) -BUG_ON (!PageLocked (page)); +if (WARN_ON_ONCE (!PageLocked (page) && + !(inode->i_sb->s_cop->flags &FS_CFLG_OWN_PAGES ))) +return -EINVAL ;return fscrypt_do_page_crypto (inode,FS_DECRYPT , lblk_num, page, page, len, offs,GFP_NOFS );
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 44/371 media: usb:zr364xx:Fix KASAN:null-ptr-deref Read in zr364xx_vidioc_querycap
In reply to Greg Kroah-Hartman[ Upstream commit 5d2e73a5f80a5b5aff3caf1ec6d39b5b3f54b26e ]
SyzKaller hit the null pointer deref while reading from uninitialized udev->product in zr364xx_vidioc_querycap().
==================================================================
BUG: KASAN: null-ptr-deref in read_word_at_a_time+0xe/0x20 include/linux/compiler.h:274 Read of size 1 at addr 0000000000000000 by task v4l_id/5287 CPU: 1 PID: 5287 Comm: v4l_id Not tainted 5.1.0-rc3-319004-g43151d6 #6 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xe8/0x16e lib/dump_stack.c:113 kasan_report.cold+0x5/0x3c mm/kasan/report.c:321 read_word_at_a_time+0xe/0x20 include/linux/compiler.h:274 strscpy+0x8a/0x280 lib/string.c:207 zr364xx_vidioc_querycap+0xb5/0x210 drivers/media/usb/zr364xx/zr364xx.c:706 v4l_querycap+0x12b/0x340 drivers/media/v4l2-core/v4l2-ioctl.c:1062 __video_do_ioctl+0x5bb/0xb40 drivers/media/v4l2-core/v4l2-ioctl.c:2874 video_usercopy+0x44e/0xf00 drivers/media/v4l2-core/v4l2-ioctl.c:3056 v4l2_ioctl+0x14e/0x1a0 drivers/media/v4l2-core/v4l2-dev.c:364 vfs_ioctl fs/ioctl.c:46 [inline] file_ioctl fs/ioctl.c:509 [inline] do_vfs_ioctl+0xced/0x12f0 fs/ioctl.c:696 ksys_ioctl+0xa0/0xc0 fs/ioctl.c:713 __do_sys_ioctl fs/ioctl.c:720 [inline] __se_sys_ioctl fs/ioctl.c:718 [inline] __x64_sys_ioctl+0x74/0xb0 fs/ioctl.c:718 do_syscall_64+0xcf/0x4f0 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x7f3b56d8b347 Code: 90 90 90 48 8b 05 f1 fa 2a 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff
ff c3 90 90 90 90 90 90 90 90 90 90 b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d c1 fa 2a 00 31 d2 48 29 c2 64
RSP: 002b:00007ffe005d5d68 EFLAGS: 00000202 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f3b56d8b347
RDX: 00007ffe005d5d70 RSI: 0000000080685600 RDI: 0000000000000003
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000400884
R13: 00007ffe005d5ec0 R14: 0000000000000000 R15: 0000000000000000
==================================================================
For this device udev->product is not initialized and accessing it causes a NULL pointer deref.
The fix is to check for NULL before strscpy() and copy empty string, if product is NULL
--- drivers/media/usb/zr364xx/zr364xx.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/media/usb/zr364xx/zr364xx.c +2 -1
@@ -703,7 +703,8 @@ static int zr364xx_vidioc_querycap(struct file *file, void *priv,struct zr364xx_camera *cam =video_drvdata (file);strscpy (cap->driver,DRIVER_DESC ,sizeof (cap->driver)); -strscpy (cap->card, cam->udev->product,sizeof (cap->card)); +if (cam->udev->product) +strscpy (cap->card, cam->udev->product,sizeof (cap->card));strscpy (cap->bus_info,dev_name (&cam->udev->dev),sizeof (cap->bus_info)); cap->device_caps = V4L2_CAP_VIDEO_CAPTURE |
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 45/371 perf annotate TUI browser: Do not use member from variable within its own initialization
In reply to Greg Kroah-Hartman[ Upstream commit da2019633f0b5c105ce658aada333422d8cb28fe ]
Some compilers will complain when using a member of a struct to initialize another member, in the same struct initialization.
For instance:
debian:8 Debian clang version 3.5.0-10 (tags/RELEASE_350/final) (based on LLVM 3.5.0)
oraclelinux:7 clang version 3.4.2 (tags/RELEASE_34/dot2-final)
Produce:
ui/browsers/annotate.c:104:12: error: variable 'ops' is uninitialized when used within its own initialization [-Werror,-Wuninitialized]
(!ops.current_entry ||
^~~1 error generated.
So use an extra variable, initialized just before that struct, to have the value used in the expressions used to init two of the struct members.
--- tools/perf/ui/browsers/annotate.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
tools/perf/ui/browsers/annotate.c +3 -2
@@ -97,11 +97,12 @@ static void annotate_browser__write(struct ui_browser *browser, void *entry, int struct annotate_browser *ab = container_of(browser, struct annotate_browser, b);struct annotation *notes =browser__annotation (browser); struct annotation_line *al = list_entry(entry, struct annotation_line, node); +const bool is_current_entry =ui_browser__is_current_entry (browser, row);struct annotation_write_ops ops = { .first_line = row ==0 , - .current_entry =ui_browser__is_current_entry (browser, row), + .current_entry = is_current_entry, .change_color = (!notes->options->hide_src_code && - (!ops.current_entry || + (!is_current_entry || (browser->use_navkeypressed && !browser->navkeypressed))), .width = browser->width,
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 46/371 media: mc-device.c: dont memset __user pointer contents
In reply to Greg Kroah-Hartman[ Upstream commit 518fa4e0e0da97ea2e17c95ab57647ce748a96e2 ]
You can't memset the contents of a __user pointer. Instead, call copy_to_user to copy links.reserved (which is zeroed) to the user memory.
This fixes this sparse warning:
SPARSE:drivers/media/mc/mc-device.c drivers/media/mc/mc-device.c:521:16: warning: incorrect type in argument 1 (different address spaces)
--- drivers/media/media-device.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/media/media-device.c +3 -2
@@ -518,8 +518,9 @@ static long media_device_enum_links32(struct media_device *mdev,if (ret)return ret; -memset (ulinks->reserved,0 ,sizeof (ulinks->reserved)); - +if (copy_to_user (ulinks->reserved, links.reserved, +sizeof (ulinks->reserved))) +return -EFAULT ;return 0 ; }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 47/371 media: saa7164: fix remove_proc_entry warning
In reply to Greg Kroah-Hartman[ Upstream commit 50710eeefbc1ed25375942aad0c4d1eb4af0f330 ]
if saa7164_proc_create() fails, saa7164_fini() will trigger a warning,
name 'saa7164'
WARNING: CPU: 1 PID: 6311 at fs/proc/generic.c:672 remove_proc_entry+0x1e8/0x3a0 ? remove_proc_entry+0x1e8/0x3a0 ? try_stop_module+0x7b/0x240 ? proc_readdir+0x70/0x70 ? rcu_read_lock_sched_held+0xd7/0x100 saa7164_fini+0x13/0x1f [saa7164] __x64_sys_delete_module+0x30c/0x480 ? __ia32_sys_delete_module+0x480/0x480 ? __x64_sys_clock_gettime+0x11e/0x1c0 ? __x64_sys_timer_create+0x1a0/0x1a0 ? trace_hardirqs_off_caller+0x40/0x180 ? do_syscall_64+0x18/0x450 do_syscall_64+0x9f/0x450 entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fix it by checking the return of proc_create_single() before calling remove_proc_entry().
--- drivers/media/pci/saa7164/saa7164-core.c | 33 ++++++++++++++++-------- 1 file changed, 22 insertions(+), 11 deletions(-)
drivers/media/pci/saa7164/saa7164-core.c +22 -11
@@ -1122,16 +1122,25 @@ static int saa7164_proc_show(struct seq_file *m, void *v) return 0; } +static struct proc_dir_entry *saa7164_pe; +static int saa7164_proc_create (void ) { -struct proc_dir_entry *pe; - - pe =proc_create_single ("saa7164" ,S_IRUGO ,NULL , saa7164_proc_show); -if (!pe) + saa7164_pe =proc_create_single ("saa7164" ,0444 ,NULL , saa7164_proc_show); +if (!saa7164_pe)return -ENOMEM ;return 0 ; } + +static void saa7164_proc_destroy (void ) +{ +if (saa7164_pe) +remove_proc_entry ("saa7164" ,NULL ); +} +#else +static int saa7164_proc_create (void ) {return 0 ; } +static void saa7164_proc_destroy (void ) {}#endif static int saa7164_thread_function (void *data)
@@ -1503,19 +1512,21 @@ static struct pci_driver saa7164_pci_driver = {static int __init saa7164_init (void ) { -printk (KERN_INFO "saa7164 driver loaded\n" ); +int ret =pci_register_driver (&saa7164_pci_driver); + +if (ret) +return ret; -#ifdef CONFIG_PROC_FS saa7164_proc_create (); -#endif -return pci_register_driver (&saa7164_pci_driver); + +pr_info ("saa7164 driver loaded\n" ); + +return 0 ; } static void __exit saa7164_fini(void) { -#ifdef CONFIG_PROC_FS -remove_proc_entry ("saa7164" ,NULL ); -#endif +saa7164_proc_destroy ();pci_unregister_driver (&saa7164_pci_driver); }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 48/371 media: staging: media: davinci_vpfe: - Fix for memory leak if decoder initialization fails.
In reply to Greg Kroah-Hartman[ Upstream commit 6995a659101bd4effa41cebb067f9dc18d77520d ]
Fix to avoid possible memory leak if the decoder initialization got failed.Free the allocated memory for file handle object before return in case decoder initialization fails.
--- drivers/staging/media/davinci_vpfe/vpfe_video.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/staging/media/davinci_vpfe/vpfe_video.c +3 -0
@@ -419,6 +419,9 @@ static int vpfe_open(struct file *file)/* If decoder is not initialized. initialize it */ if (!video->initialized &&vpfe_update_pipe_state (video)) {mutex_unlock (&video->lock); +v4l2_fh_del (&handle->vfh); +v4l2_fh_exit (&handle->vfh); +kfree (handle);return -ENODEV ; }/* Increment device users counter */
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 49/371 net: phy: Check against net_device being NULL
In reply to Greg Kroah-Hartman[ Upstream commit 82c76aca81187b3d28a6fb3062f6916450ce955e ]
In general, we don't want MAC drivers calling phy_attach_direct with the net_device being NULL. Add checks against this in all the functions calling it: phy_attach() and phy_connect_direct().
--- drivers/net/phy/phy_device.c | 6 ++++++ 1 file changed, 6 insertions(+)
drivers/net/phy/phy_device.c +6 -0
@@ -948,6 +948,9 @@ int phy_connect_direct(struct net_device *dev, struct phy_device *phydev, {int rc; +if (!dev) +return -EINVAL ; + rc =phy_attach_direct (dev, phydev, phydev->dev_flags, interface);if (rc)return rc;
@@ -1290,6 +1293,9 @@ struct phy_device *phy_attach(struct net_device *dev, const char *bus_id,struct device *d;int rc; +if (!dev) +return ERR_PTR (-EINVAL ); +/* Search the list of PHY devices on the mdio bus for the * PHY with the requested name */
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 50/371 crypto: talitos - properly handle split ICV.
In reply to Greg Kroah-Hartman[ Upstream commit eae55a586c3c8b50982bad3c3426e9c9dd7a0075 ]
The driver assumes that the ICV is as a single piece in the last element of the scatterlist. This assumption is wrong.
This patch ensures that the ICV is properly handled regardless of the scatterlist layout.
--- drivers/crypto/talitos.c | 26 +++++++++++++++----------- 1 file changed, 15 insertions(+), 11 deletions(-)
drivers/crypto/talitos.c +15 -11
@@ -1001,7 +1001,6 @@ static void ipsec_esp_encrypt_done(struct device *dev,unsigned int authsize =crypto_aead_authsize (authenc);unsigned int ivsize =crypto_aead_ivsize (authenc);struct talitos_edesc *edesc; -struct scatterlist *sg;void *icvdata; edesc = container_of(desc, struct talitos_edesc, desc);
@@ -1015,9 +1014,8 @@ static void ipsec_esp_encrypt_done(struct device *dev,else icvdata = &edesc->link_tbl[edesc->src_nents + edesc->dst_nents +2 ]; - sg =sg_last (areq->dst, edesc->dst_nents); -memcpy ((char *)sg_virt (sg) + sg->length - authsize, - icvdata, authsize); +sg_pcopy_from_buffer (areq->dst, edesc->dst_nents ? :1 , icvdata, + authsize, areq->assoclen + areq->cryptlen); }dma_unmap_single (dev, edesc->iv_dma, ivsize,DMA_TO_DEVICE );
@@ -1035,7 +1033,6 @@ static void ipsec_esp_decrypt_swauth_done(struct device *dev,struct crypto_aead *authenc =crypto_aead_reqtfm (req);unsigned int authsize =crypto_aead_authsize (authenc);struct talitos_edesc *edesc; -struct scatterlist *sg;char *oicv, *icv;struct talitos_private *priv =dev_get_drvdata (dev);bool is_sec1 =has_ftr_sec1 (priv);
@@ -1045,9 +1042,18 @@ static void ipsec_esp_decrypt_swauth_done(struct device *dev,ipsec_esp_unmap (dev, edesc, req);if (!err) { +char icvdata[SHA512_DIGEST_SIZE ]; +int nents = edesc->dst_nents ? :1 ; +unsigned int len = req->assoclen + req->cryptlen; +/* auth check */ - sg =sg_last (req->dst, edesc->dst_nents ? :1 ); - icv = (char *)sg_virt (sg) + sg->length - authsize; +if (nents >1 ) { +sg_pcopy_to_buffer (req->dst, nents, icvdata, authsize, + len - authsize); + icv = icvdata; + }else { + icv = (char *)sg_virt (req->dst) + len - authsize; + }if (edesc->dma_len) {if (is_sec1)
@@ -1463,7 +1469,6 @@ static int aead_decrypt(struct aead_request *req)struct talitos_ctx *ctx =crypto_aead_ctx (authenc);struct talitos_private *priv =dev_get_drvdata (ctx->dev);struct talitos_edesc *edesc; -struct scatterlist *sg;void *icvdata; req->cryptlen -= authsize;
@@ -1497,9 +1502,8 @@ static int aead_decrypt(struct aead_request *req)else icvdata = &edesc->link_tbl[0 ]; - sg =sg_last (req->src, edesc->src_nents ? :1 ); - -memcpy (icvdata, (char *)sg_virt (sg) + sg->length - authsize, authsize); +sg_pcopy_to_buffer (req->src, edesc->src_nents ? :1 , icvdata, authsize, + req->assoclen + req->cryptlen - authsize);return ipsec_esp (edesc, req, ipsec_esp_decrypt_swauth_done); }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 51/371 crypto: talitos - Align SEC1 accesses to 32 bits boundaries.
In reply to Greg Kroah-Hartman[ Upstream commit c9cca7034b34a2d82e9a03b757de2485c294851c ]
The MPC885 reference manual states:
SEC Lite-initiated 8xx writes can occur only on 32-bit-word boundaries, but reads can occur on any byte boundary. Writing back a header read from a non-32-bit-word boundary will yield unpredictable results.
In order to ensure that, cra_alignmask is set to 3 for SEC1.
--- drivers/crypto/talitos.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/crypto/talitos.c +4 -1
@@ -3192,7 +3192,10 @@ static struct talitos_crypto_alg *talitos_alg_alloc(struct device *dev, alg->cra_priority = t_alg->algt.priority; else alg->cra_priority = TALITOS_CRA_PRIORITY; - alg->cra_alignmask =0 ; +if (has_ftr_sec1 (priv)) + alg->cra_alignmask =3 ; +else + alg->cra_alignmask =0 ; alg->cra_ctxsize =sizeof (struct talitos_ctx ); alg->cra_flags |=CRYPTO_ALG_KERN_DRIVER_ONLY ;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 52/371 tua6100: Avoid build warnings.
In reply to Greg Kroah-Hartman[ Upstream commit 621ccc6cc5f8d6730b740d31d4818227866c93c9 ]
Rename _P to _P_VAL and _R to _R_VAL to avoid global namespace conflicts:
drivers/media/dvb-frontends/tua6100.c: In function ‘tua6100_set_params’:drivers/media/dvb-frontends/tua6100.c:79: warning: "_P" redefined
#define _P 32
In file included from ./include/acpi/platform/aclinux.h:54,
from ./include/acpi/platform/acenv.h:152,
from ./include/acpi/acpi.h:22,
from ./include/linux/acpi.h:34,
from ./include/linux/i2c.h:17,
from drivers/media/dvb-frontends/tua6100.h:30,
from drivers/media/dvb-frontends/tua6100.c:32:./include/linux/ctype.h:14: note: this is the location of the previous definition
#define _P 0x10 /* punct */
--- drivers/media/dvb-frontends/tua6100.c | 22 +++++++++++----------- 1 file changed, 11 insertions(+), 11 deletions(-)
drivers/media/dvb-frontends/tua6100.c +11 -11
@@ -75,8 +75,8 @@ static int tua6100_set_params(struct dvb_frontend *fe)struct i2c_msg msg1 = { .addr = priv->i2c_address, .flags =0 , .buf = reg1, .len =4 };struct i2c_msg msg2 = { .addr = priv->i2c_address, .flags =0 , .buf = reg2, .len =3 }; -#define _R 4 -#define _P 32 +#define _R_VAL 4 +#define _P_VAL 32#define _ri 4000000// setup register 0
@@ -91,14 +91,14 @@ static int tua6100_set_params(struct dvb_frontend *fe)else reg1[1 ] =0x0c ; -if (_P ==64 ) +if (_P_VAL ==64 ) reg1[1 ] |=0x40 ;if (c->frequency >=1525000 ) reg1[1 ] |=0x80 ;// register 2 - reg2[1 ] = (_R >>8 ) &0x03 ; - reg2[2 ] = _R; + reg2[1 ] = (_R_VAL >>8 ) &0x03 ; + reg2[2 ] = _R_VAL;if (c->frequency <1455000 ) reg2[1 ] |=0x1c ;else if (c->frequency <1630000 )
@@ -110,18 +110,18 @@ static int tua6100_set_params(struct dvb_frontend *fe)* The N divisor ratio (note: c->frequency is in kHz, but we * need it in Hz) */ - prediv = (c->frequency * _R) / (_ri /1000 ); - div = prediv / _P; + prediv = (c->frequency * _R_VAL) / (_ri /1000 ); + div = prediv / _P_VAL; reg1[1 ] |= (div >>9 ) &0x03 ; reg1[2 ] = div >>1 ; reg1[3 ] = (div <<7 ); - priv->frequency = ((div * _P) * (_ri /1000 )) / _R; + priv->frequency = ((div * _P_VAL) * (_ri /1000 )) / _R_VAL;// Finally, calculate and store the value for A - reg1[3 ] |= (prediv - (div*_P)) &0x7f ; + reg1[3 ] |= (prediv - (div*_P_VAL)) &0x7f ; -#undef _R -#undef _P +#undef _R_VAL +#undef _P_VAL#undef _riif (fe->ops.i2c_gate_ctrl)
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 53/371 batman-adv: Fix duplicated OGMs on NETDEV_UP
In reply to Greg Kroah-Hartman[ Upstream commit 9e6b5648bbc4cd48fab62cecbb81e9cc3c6e7e88 ]
The state of slave interfaces are handled differently depending on whether the interface is up or not. All active interfaces (IFF_UP) will transmit OGMs. But for B.A.T.M.A.N. IV, also non-active interfaces are scheduling (low TTL) OGMs on active interfaces. The code which setups and schedules the OGMs must therefore already be called when the interfaces gets added as slave interface and the transmit function must then check whether it has to send out the OGM or not on the specific slave interface.
But the commit f0d97253fb5f ("batman-adv: remove ogm_emit and ogm_schedule API calls") moved the setup code from the enable function to the activate function. The latter is called either when the added slave was already up when batadv_hardif_enable_interface processed the new interface or when a NETDEV_UP event was received for this slave interfac. As result, each NETDEV_UP would schedule a new OGM worker for the interface and thus OGMs would be send a lot more than expected.
--- net/batman-adv/bat_iv_ogm.c | 4 ++-- net/batman-adv/hard-interface.c | 3 +++ net/batman-adv/types.h | 3 +++ 3 files changed, 8 insertions(+), 2 deletions(-)
net/batman-adv/bat_iv_ogm.c +2 -2
@@ -2349,7 +2349,7 @@ batadv_iv_ogm_neigh_is_sob(struct batadv_neigh_node *neigh1,return ret; } -static void batadv_iv_iface_activate (struct batadv_hard_iface *hard_iface) +static void batadv_iv_iface_enabled (struct batadv_hard_iface *hard_iface) {/* begin scheduling originator messages on that interface */ batadv_iv_ogm_schedule (hard_iface);
@@ -2695,8 +2695,8 @@ static void batadv_iv_gw_dump(struct sk_buff *msg, struct netlink_callback *cb,static struct batadv_algo_ops batadv_batman_iv__read_mostly = { .name ="BATMAN_IV" , .iface = { - .activate = batadv_iv_iface_activate, .enable = batadv_iv_ogm_iface_enable, + .enabled = batadv_iv_iface_enabled, .disable = batadv_iv_ogm_iface_disable, .update_mac = batadv_iv_ogm_iface_update_mac, .primary_set = batadv_iv_ogm_primary_iface_set,
net/batman-adv/hard-interface.c +3 -0
@@ -807,6 +807,9 @@ int batadv_hardif_enable_interface(struct batadv_hard_iface *hard_iface,batadv_hardif_recalc_extra_skbroom (soft_iface); +if (bat_priv->algo_ops->iface.enabled) + bat_priv->algo_ops->iface.enabled (hard_iface); + out:return 0 ;
net/batman-adv/types.h +3 -0
@@ -2135,6 +2135,9 @@ struct batadv_algo_iface_ops {/** @enable: init routing info when hard-interface is enabled */ int (*enable)(struct batadv_hard_iface *hard_iface); +/** @enabled: notification when hard-interface was enabled (optional) */ +void (*enabled)(struct batadv_hard_iface *hard_iface); +/** @disable: de-init routing info when hard-interface is disabled */ void (*disable)(struct batadv_hard_iface *hard_iface);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 54/371 locking/lockdep: Fix OOO unlock when hlocks need merging
In reply to Greg Kroah-Hartman[ Upstream commit 8c8889d8eaf4501ae4aaf870b6f8f55db5d5109a ]
The sequence
static DEFINE_WW_CLASS(test_ww_class); struct ww_acquire_ctx ww_ctx; struct ww_mutex ww_lock_a; struct ww_mutex ww_lock_b; struct mutex lock_c; struct mutex lock_d; ww_acquire_init(&ww_ctx, &test_ww_class); ww_mutex_init(&ww_lock_a, &test_ww_class); ww_mutex_init(&ww_lock_b, &test_ww_class); mutex_init(&lock_c); ww_mutex_lock(&ww_lock_a, &ww_ctx); mutex_lock(&lock_c); ww_mutex_lock(&ww_lock_b, &ww_ctx); mutex_unlock(&lock_c); (*) ww_mutex_unlock(&ww_lock_b); ww_mutex_unlock(&ww_lock_a); ww_acquire_fini(&ww_ctx);
triggers the following WARN in __lock_release() when doing the unlock at *:
DEBUG_LOCKS_WARN_ON(curr->lockdep_depth != depth - 1);
The problem is that the WARN check doesn't take into account the merging of ww_lock_a and ww_lock_b which results in decreasing curr->lockdep_depth by 2 not only 1.
Note that the following sequence doesn't trigger the WARN, since there won't be any hlock merging.
ww_acquire_init(&ww_ctx, &test_ww_class); ww_mutex_init(&ww_lock_a, &test_ww_class); ww_mutex_init(&ww_lock_b, &test_ww_class); mutex_init(&lock_c); mutex_init(&lock_d); ww_mutex_lock(&ww_lock_a, &ww_ctx); mutex_lock(&lock_c); mutex_lock(&lock_d); ww_mutex_lock(&ww_lock_b, &ww_ctx); mutex_unlock(&lock_d); ww_mutex_unlock(&ww_lock_b); ww_mutex_unlock(&ww_lock_a); mutex_unlock(&lock_c); ww_acquire_fini(&ww_ctx);
In general both of the above two sequences are valid and shouldn't trigger any lockdep warning.
Fix this by taking the decrement due to the hlock merging into account during lock release and hlock class re-setting. Merging can't happen during lock downgrading since there won't be a new possibility to merge hlocks in that case, so add a WARN if merging still happens then.
--- kernel/locking/lockdep.c | 41 ++++++++++++++++++++++++++++------------ 1 file changed, 29 insertions(+), 12 deletions(-)
kernel/locking/lockdep.c +29 -12
@@ -3623,7 +3623,7 @@ static int __lock_acquire(struct lockdep_map *lock, unsigned int subclass, hlock->references =2 ; } -return 1 ; +return 2 ; } }
@@ -3829,22 +3829,33 @@ static struct held_lock *find_held_lock(struct task_struct *curr, }static int reacquire_held_locks (struct task_struct *curr,unsigned int depth, -int idx) +int idx,unsigned int *merged) {struct held_lock *hlock; +int first_idx = idx;if (DEBUG_LOCKS_WARN_ON (!irqs_disabled ()))return 0 ;for (hlock = curr->held_locks + idx; idx < depth; idx++, hlock++) { -if (!__lock_acquire (hlock->instance, +switch (__lock_acquire (hlock->instance,hlock_class (hlock)->subclass, hlock->trylock, hlock->read, hlock->check, hlock->hardirqs_off, hlock->nest_lock, hlock->acquire_ip, - hlock->references, hlock->pin_count)) + hlock->references, hlock->pin_count)) { +case 0 :return 1 ; +case 1 : +break ; +case 2 : + *merged += (idx == first_idx); +break ; +default : +WARN_ON (1 ); +return 0 ; + } }return 0 ; }
@@ -3855,9 +3866,9 @@ __lock_set_class(struct lockdep_map *lock, const char *name, unsigned long ip) {struct task_struct *curr = current; +unsigned int depth, merged =0 ;struct held_lock *hlock;struct lock_class *class; -unsigned int depth;int i;if (unlikely (!debug_locks))
@@ -3882,14 +3893,14 @@ __lock_set_class(struct lockdep_map *lock, const char *name, curr->lockdep_depth = i; curr->curr_chain_key = hlock->prev_chain_key; -if (reacquire_held_locks (curr, depth, i)) +if (reacquire_held_locks (curr, depth, i, &merged))return 0 ;/* * I took it apart and put it back together again, except now I have * these 'spare' parts.. where shall I put them. */ -if (DEBUG_LOCKS_WARN_ON (curr->lockdep_depth != depth)) +if (DEBUG_LOCKS_WARN_ON (curr->lockdep_depth != depth - merged))return 0 ;return 1 ; }
@@ -3897,8 +3908,8 @@ __lock_set_class(struct lockdep_map *lock, const char *name,static int __lock_downgrade (struct lockdep_map *lock,unsigned long ip) {struct task_struct *curr = current; +unsigned int depth, merged =0 ;struct held_lock *hlock; -unsigned int depth;int i;if (unlikely (!debug_locks))
@@ -3923,7 +3934,11 @@ static int __lock_downgrade(struct lockdep_map *lock, unsigned long ip) hlock->read =1 ; hlock->acquire_ip = ip; -if (reacquire_held_locks (curr, depth, i)) +if (reacquire_held_locks (curr, depth, i, &merged)) +return 0 ; + +/* Merging can't happen with unchanged classes.. */ +if (DEBUG_LOCKS_WARN_ON (merged))return 0 ;/*
@@ -3932,6 +3947,7 @@ static int __lock_downgrade(struct lockdep_map *lock, unsigned long ip)*/ if (DEBUG_LOCKS_WARN_ON (curr->lockdep_depth != depth))return 0 ; +return 1 ; }
@@ -3946,8 +3962,8 @@ static int __lock_release(struct lockdep_map *lock, int nested, unsigned long ip) { struct task_struct *curr = current; +unsigned int depth, merged =1 ;struct held_lock *hlock; -unsigned int depth;int i;if (unlikely (!debug_locks))
@@ -4002,14 +4018,15 @@ __lock_release(struct lockdep_map *lock, int nested, unsigned long ip)if (i == depth-1 )return 1 ; -if (reacquire_held_locks (curr, depth, i +1 )) +if (reacquire_held_locks (curr, depth, i +1 , &merged))return 0 ;/* * We had N bottles of beer on the wall, we drank one, but now * there's not N-1 bottles of beer left on the wall... +* Pouring two of the bottles together is acceptable. */ -DEBUG_LOCKS_WARN_ON (curr->lockdep_depth != depth-1 ); +DEBUG_LOCKS_WARN_ON (curr->lockdep_depth != depth - merged);/* * Since reacquire_held_locks() would have called check_chain_key()
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 55/371 locking/lockdep: Fix merging of hlocks with non-zero references
In reply to Greg Kroah-Hartman[ Upstream commit d9349850e188b8b59e5322fda17ff389a1c0cd7d ]
The sequence
static DEFINE_WW_CLASS(test_ww_class); struct ww_acquire_ctx ww_ctx; struct ww_mutex ww_lock_a; struct ww_mutex ww_lock_b; struct ww_mutex ww_lock_c; struct mutex lock_c; ww_acquire_init(&ww_ctx, &test_ww_class); ww_mutex_init(&ww_lock_a, &test_ww_class); ww_mutex_init(&ww_lock_b, &test_ww_class); ww_mutex_init(&ww_lock_c, &test_ww_class); mutex_init(&lock_c); ww_mutex_lock(&ww_lock_a, &ww_ctx); mutex_lock(&lock_c); ww_mutex_lock(&ww_lock_b, &ww_ctx); ww_mutex_lock(&ww_lock_c, &ww_ctx); mutex_unlock(&lock_c); (*) ww_mutex_unlock(&ww_lock_c); ww_mutex_unlock(&ww_lock_b); ww_mutex_unlock(&ww_lock_a); ww_acquire_fini(&ww_ctx); (**)
will trigger the following error in __lock_release() when calling mutex_release() at **:
DEBUG_LOCKS_WARN_ON(depth <= 0)
The problem is that the hlock merging happening at * updates the references for test_ww_class incorrectly to 3 whereas it should've updated it to 4 (representing all the instances for ww_ctx and ww_lock_[abc]).
Fix this by updating the references during merging correctly taking into account that we can have non-zero references (both for the hlock that we merge into another hlock or for the hlock we are merging into).
--- kernel/locking/lockdep.c | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-)
kernel/locking/lockdep.c +9 -9
@@ -3611,17 +3611,17 @@ static int __lock_acquire(struct lockdep_map *lock, unsigned int subclass,if (depth) { hlock = curr->held_locks + depth -1 ;if (hlock->class_idx == class_idx && nest_lock) { -if (hlock->references) { -/* -* Check: unsigned int references:12, overflow. -*/ -if (DEBUG_LOCKS_WARN_ON (hlock->references == (1 <<12 )-1 )) -return 0 ; +if (!references) + references++; +if (!hlock->references) hlock->references++; - }else { - hlock->references =2 ; - } + + hlock->references += references; + +/* Overflow */ +if (DEBUG_LOCKS_WARN_ON (hlock->references < references)) +return 0 ;return 2 ; }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 56/371 media: wl128x: Fix some error handling in fm_v4l2_init_video_device()
In reply to Greg Kroah-Hartman[ Upstream commit 69fbb3f47327d959830c94bf31893972b8c8f700 ]
X-Originating-IP: [10.175.113.25]
X-CFilter-Loop: Reflected
The fm_v4l2_init_video_device() forget to unregister v4l2/video device in the error path, it could lead to UAF issue, eg,
BUG: KASAN: use-after-free in atomic64_read include/asm-generic/atomic-instrumented.h:836 [inline] BUG: KASAN: use-after-free in atomic_long_read include/asm-generic/atomic-long.h:28 [inline] BUG: KASAN: use-after-free in __mutex_unlock_slowpath+0x92/0x690 kernel/locking/mutex.c:1206 Read of size 8 at addr ffff8881e84a7c70 by task v4l_id/3659 CPU: 1 PID: 3659 Comm: v4l_id Not tainted 5.1.0 #8 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xa9/0x10e lib/dump_stack.c:113 print_address_description+0x65/0x270 mm/kasan/report.c:187 kasan_report+0x149/0x18d mm/kasan/report.c:317 atomic64_read include/asm-generic/atomic-instrumented.h:836 [inline] atomic_long_read include/asm-generic/atomic-long.h:28 [inline] __mutex_unlock_slowpath+0x92/0x690 kernel/locking/mutex.c:1206 fm_v4l2_fops_open+0xac/0x120 [fm_drv] v4l2_open+0x191/0x390 [videodev] chrdev_open+0x20d/0x570 fs/char_dev.c:417 do_dentry_open+0x700/0xf30 fs/open.c:777 do_last fs/namei.c:3416 [inline] path_openat+0x7c4/0x2a90 fs/namei.c:3532 do_filp_open+0x1a5/0x2b0 fs/namei.c:3563 do_sys_open+0x302/0x490 fs/open.c:1069 do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x7f8180c17c8e ... Allocated by task 3642: set_track mm/kasan/common.c:87 [inline] __kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:497 fm_drv_init+0x13/0x1000 [fm_drv] do_one_initcall+0xbc/0x47d init/main.c:901 do_init_module+0x1b5/0x547 kernel/module.c:3456 load_module+0x6405/0x8c10 kernel/module.c:3804 __do_sys_finit_module+0x162/0x190 kernel/module.c:3898 do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe Freed by task 3642: set_track mm/kasan/common.c:87 [inline] __kasan_slab_free+0x130/0x180 mm/kasan/common.c:459 slab_free_hook mm/slub.c:1429 [inline] slab_free_freelist_hook mm/slub.c:1456 [inline] slab_free mm/slub.c:3003 [inline] kfree+0xe1/0x270 mm/slub.c:3958 fm_drv_init+0x1e6/0x1000 [fm_drv] do_one_initcall+0xbc/0x47d init/main.c:901 do_init_module+0x1b5/0x547 kernel/module.c:3456 load_module+0x6405/0x8c10 kernel/module.c:3804 __do_sys_finit_module+0x162/0x190 kernel/module.c:3898 do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe
Add relevant unregister functions to fix it.
--- drivers/media/radio/wl128x/fmdrv_v4l2.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/media/radio/wl128x/fmdrv_v4l2.c +3 -0
@@ -550,6 +550,7 @@ int fm_v4l2_init_video_device(struct fmdev *fmdev, int radio_nr)/* Register with V4L2 subsystem as RADIO device */ if (video_register_device (&gradio_dev,VFL_TYPE_RADIO , radio_nr)) { +v4l2_device_unregister (&fmdev->v4l2_dev);fmerr ("Could not register video device\n" );return -ENOMEM ; }
@@ -563,6 +564,8 @@ int fm_v4l2_init_video_device(struct fmdev *fmdev, int radio_nr)if (ret <0 ) {fmerr ("(fmdev): Can't init ctrl handler\n" );v4l2_ctrl_handler_free (&fmdev->ctrl_handler); +video_unregister_device (fmdev->radio_dev); +v4l2_device_unregister (&fmdev->v4l2_dev);return -EBUSY ; }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 57/371 net: hns3: add a check to pointer in error_detected and slot_reset
In reply to Greg Kroah-Hartman[ Upstream commit 661262bc3e0ecc9a1aed39c6b2a99766da2c22e2 ]
If we add a VF without loading hclgevf.ko and then there is a RAS error occurs, PCIe AER will call error_detected and slot_reset of all functions, and will get a NULL pointer when we check ad_dev->ops->handle_hw_ras_error. This will cause a call trace and failures on handling of follow-up RAS errors.
This patch check ae_dev and ad_dev->ops at first to solve above issues.
--- drivers/net/ethernet/hisilicon/hns3/hns3_enet.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/net/ethernet/hisilicon/hns3/hns3_enet.c +5 -2
@@ -1847,9 +1847,9 @@ static pci_ers_result_t hns3_error_detected(struct pci_dev *pdev,if (state == pci_channel_io_perm_failure)return PCI_ERS_RESULT_DISCONNECT ; -if (!ae_dev) { +if (!ae_dev || !ae_dev->ops) {dev_err (&pdev->dev, -"Can't recover - error happened during device init\n" ); +"Can't recover - error happened before device initialized\n" );return PCI_ERS_RESULT_NONE ; }
@@ -1868,6 +1868,9 @@ static pci_ers_result_t hns3_slot_reset(struct pci_dev *pdev)dev_info (dev,"requesting reset due to PCI error\n" ); +if (!ae_dev || !ae_dev->ops) +return PCI_ERS_RESULT_NONE ; +/* request the reset */ if (ae_dev->ops->reset_event) {if (!ae_dev->override_pci_need_reset)
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 58/371 net: hns3: set ops to null when unregister ad_dev
In reply to Greg Kroah-Hartman[ Upstream commit 594a81b39525f0a17e92c2e0b167ae1400650380 ]
The hclge/hclgevf and hns3 module can be unloaded independently, when hclge/hclgevf unloaded firstly, the ops of ae_dev should be set to NULL, otherwise it will cause an use-after-free problem.
--- drivers/net/ethernet/hisilicon/hns3/hnae3.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/net/ethernet/hisilicon/hns3/hnae3.c +2 -0
@@ -247,6 +247,7 @@ void hnae3_unregister_ae_algo(struct hnae3_ae_algo *ae_algo) ae_algo->ops->uninit_ae_dev (ae_dev);hnae3_set_bit (ae_dev->flag,HNAE3_DEV_INITED_B ,0 ); + ae_dev->ops =NULL ; }list_del (&ae_algo->node);
@@ -347,6 +348,7 @@ void hnae3_unregister_ae_dev(struct hnae3_ae_dev *ae_dev) ae_algo->ops->uninit_ae_dev (ae_dev);hnae3_set_bit (ae_dev->flag,HNAE3_DEV_INITED_B ,0 ); + ae_dev->ops =NULL ; }list_del (&ae_dev->node);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 59/371 cpupower : frequency-set -r option misses the last cpu in related cpu list
In reply to Greg Kroah-Hartman[ Upstream commit 04507c0a9385cc8280f794a36bfff567c8cc1042 ]
To set frequency on specific cpus using cpupower, following syntax can be used :
cpupower -c #i frequency-set -f #f -r
While setting frequency using cpupower frequency-set command, if we use '-r' option, it is expected to set frequency for all cpus related to cpu #i. But it is observed to be missing the last cpu in related cpu list. This patch fixes the problem.
--- tools/power/cpupower/utils/cpufreq-set.c | 2 ++ 1 file changed, 2 insertions(+)
tools/power/cpupower/utils/cpufreq-set.c +2 -0
@@ -306,6 +306,8 @@ int cmd_freq_set(int argc, char **argv)bitmask_setbit (cpus_chosen, cpus->cpu); cpus = cpus->next; } +/* Set the last cpu in related cpus list */ +bitmask_setbit (cpus_chosen, cpus->cpu);cpufreq_put_related_cpus (cpus); } }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 60/371 arm64: mm: make CONFIG_ZONE_DMA32 configurable
In reply to Greg Kroah-Hartman[ Upstream commit 0c1f14ed12262f45a3af1d588e4d7bd12438b8f5 ]
This change makes CONFIG_ZONE_DMA32 defuly y and allows users to overwrite it only when CONFIG_EXPERT=y.
For the SoCs that do not need CONFIG_ZONE_DMA32, this is the first step to manage all available memory by a single zone(normal zone) to reduce the overhead of multiple zones.
The change also fixes a build error when CONFIG_NUMA=y and CONFIG_ZONE_DMA32=n.
arch/arm64/mm/init.c:195:17: error: use of undeclared identifier 'ZONE_DMA32'
max_zone_pfns[ZONE_DMA32] = PFN_DOWN(max_zone_dma_phys());
Change since v1:
1. only expose CONFIG_ZONE_DMA32 when CONFIG_EXPERT=y
2. remove redundant IS_ENABLED(CONFIG_ZONE_DMA32)
--- arch/arm64/Kconfig | 3 ++- arch/arm64/mm/init.c | 5 +++-- 2 files changed, 5 insertions(+), 3 deletions(-)
arch/arm64/Kconfig +2 -1
@@ -258,7 +258,8 @@ config GENERIC_CALIBRATE_DELAY def_bool y config ZONE_DMA32 - def_bool y + bool "Support DMA32 zone" if EXPERT + default y config HAVE_GENERIC_GUP def_bool y
arch/arm64/mm/init.c +3 -2
@@ -191,8 +191,9 @@ static void __init zone_sizes_init(unsigned long min, unsigned long max) {unsigned long max_zone_pfns[MAX_NR_ZONES ] = {0 }; -if (IS_ENABLED (CONFIG_ZONE_DMA32 )) - max_zone_pfns[ZONE_DMA32 ] =PFN_DOWN (max_zone_dma_phys ()); +#ifdef CONFIG_ZONE_DMA32 + max_zone_pfns[ZONE_DMA32 ] =PFN_DOWN (max_zone_dma_phys ()); +#endif max_zone_pfns[ZONE_NORMAL ] = max;free_area_init_nodes (max_zone_pfns);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 61/371 media: imx7-mipi-csis: Propagate the error if clock enabling fails
In reply to Greg Kroah-Hartman[ Upstream commit 2b393f91c651c16d5c09f5c7aa689e58a79df34e ]
Currently the return value from clk_bulk_prepare_enable() is checked, but it is not propagate it in the case of failure.
Fix it and also move the error message to the caller of mipi_csis_clk_enable().
--- drivers/staging/media/imx/imx7-mipi-csis.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-)
drivers/staging/media/imx/imx7-mipi-csis.c +7 -7
@@ -455,13 +455,9 @@ static void mipi_csis_set_params(struct csi_state *state) MIPI_CSIS_CMN_CTRL_UPDATE_SHADOW_CTRL); } -static void mipi_csis_clk_enable (struct csi_state *state) +static int mipi_csis_clk_enable (struct csi_state *state) { -int ret; - - ret =clk_bulk_prepare_enable (state->num_clks, state->clks); -if (ret <0 ) -dev_err (state->dev,"failed to enable clocks\n" ); +return clk_bulk_prepare_enable (state->num_clks, state->clks); }static void mipi_csis_clk_disable (struct csi_state *state)
@@ -985,7 +981,11 @@ static int mipi_csis_probe(struct platform_device *pdev)if (ret <0 )return ret; -mipi_csis_clk_enable (state); + ret =mipi_csis_clk_enable (state); +if (ret <0 ) { +dev_err (state->dev,"failed to enable clocks: %d\n" , ret); +return ret; + } ret =devm_request_irq (dev, state->irq, mipi_csis_irq_handler,0 ,dev_name (dev), state);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 62/371 perf jvmti: Address gcc string overflow warning for strncpy()
In reply to Greg Kroah-Hartman[ Upstream commit 279ab04dbea1370d2eac0f854270369ccaef8a44 ]
We are getting false positive gcc warning when we compile with gcc9 (9.1.1):
CC jvmti/libjvmti.o
In file included from /usr/include/string.h:494,
from jvmti/libjvmti.c:5:
In function ‘strncpy’,
inlined from ‘copy_class_filename.constprop’ at jvmti/libjvmti.c:166:3:
/usr/include/bits/string_fortified.h:106:10: error: ‘__builtin_strncpy’ specified bound depends on the length of the source argument [-Werror=stringop-overflow=]
106 | return __builtin___strncpy_chk (__dest, __src, __len, __bos (__dest));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
jvmti/libjvmti.c: In function ‘copy_class_filename.constprop’:
jvmti/libjvmti.c:165:26: note: length computed here
165 | size_t file_name_len = strlen(file_name);
| ^~~~~~~~~~~~~~~~~cc1: all warnings being treated as errors
As per Arnaldo's suggestion use strlcpy(), which does the same thing and keeps gcc silent.
--- tools/perf/jvmti/libjvmti.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
tools/perf/jvmti/libjvmti.c +2 -2
@@ -1,5 +1,6 @@// SPDX-License-Identifier: GPL-2.0 #include <linux/compiler.h> +#include <linux/string.h> #include <sys/types.h> #include <stdio.h> #include <string.h>
@@ -162,8 +163,7 @@ copy_class_filename(const char * class_sign, const char * file_name, char * resu result[i] ='\0' ; }else {/* fallback case */ -size_t file_name_len =strlen (file_name); -strncpy (result, file_name, file_name_len < max_length ? file_name_len : max_length); +strlcpy (result, file_name, max_length); } }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 63/371 media: aspeed: change irq to threaded irq
In reply to Greg Kroah-Hartman[ Upstream commit 12ae1c1bf5db2f33fcd9092a96f630291c4b181a ]
Differently from other Aspeed drivers, this driver calls clock control APIs in interrupt context. Since ECLK is coupled with a reset bit in clk-aspeed module, aspeed_clk_enable will make 10ms of busy waiting delay for triggering the reset and it will eventually disturb other drivers' interrupt handling. To fix this issue, this commit changes this driver's irq to threaded irq so that the delay can be happened in a thread context.
--- drivers/media/platform/aspeed-video.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/media/platform/aspeed-video.c +3 -2
@@ -1600,8 +1600,9 @@ static int aspeed_video_init(struct aspeed_video *video)return -ENODEV ; } - rc =devm_request_irq (dev, irq, aspeed_video_irq,IRQF_SHARED , -DEVICE_NAME , video); + rc =devm_request_threaded_irq (dev, irq,NULL , aspeed_video_irq, +IRQF_ONESHOT |IRQF_SHARED ,DEVICE_NAME , + video);if (rc <0 ) {dev_err (dev,"Unable to request IRQ %d\n" , irq);return rc;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 64/371 net: stmmac: dwmac4: fix flow control issue
In reply to Greg Kroah-Hartman[ Upstream commit ee326fd01e79dfa42014d55931260b68b9fa3273 ]
Current dwmac4_flow_ctrl will not clear GMAC_RX_FLOW_CTRL_RFE/GMAC_RX_FLOW_CTRL_RFE bits, so MAC hw will keep flow control on although expecting flow control off by ethtool. Add codes to fix it.
--- drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c +6 -2
@@ -475,8 +475,9 @@ static void dwmac4_flow_ctrl(struct mac_device_info *hw, unsigned int duplex,if (fc &FLOW_RX ) {pr_debug ("\tReceive Flow-Control ON\n" ); flow |=GMAC_RX_FLOW_CTRL_RFE ; -writel (flow, ioaddr +GMAC_RX_FLOW_CTRL ); } +writel (flow, ioaddr +GMAC_RX_FLOW_CTRL ); +if (fc &FLOW_TX ) {pr_debug ("\tTransmit Flow-Control ON\n" );
@@ -484,7 +485,7 @@ static void dwmac4_flow_ctrl(struct mac_device_info *hw, unsigned int duplex,pr_debug ("\tduplex mode: PAUSE %d\n" , pause_time);for (queue =0 ; queue < tx_cnt; queue++) { - flow |=GMAC_TX_FLOW_CTRL_TFE ; + flow =GMAC_TX_FLOW_CTRL_TFE ;if (duplex) flow |=
@@ -492,6 +493,9 @@ static void dwmac4_flow_ctrl(struct mac_device_info *hw, unsigned int duplex,writel (flow, ioaddr +GMAC_QX_TX_FLOW_CTRL (queue)); } + }else { +for (queue =0 ; queue < tx_cnt; queue++) +writel (0 , ioaddr +GMAC_QX_TX_FLOW_CTRL (queue)); } }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 65/371 net: stmmac: modify default value of tx-frames
In reply to Greg Kroah-Hartman[ Upstream commit d2facb4b3983425f6776c24dd678a82dbe673773 ]
the default value of tx-frames is 25, it's too late when passing tstamp to stack, then the ptp4l will fail:
ptp4l -i eth0 -f gPTP.cfg -m
ptp4l: selected /dev/ptp0 as PTP clock
ptp4l: port 1: INITIALIZING to LISTENING on INITIALIZE
ptp4l: port 0: INITIALIZING to LISTENING on INITIALIZE
ptp4l: port 1: link up
ptp4l: timed out while polling for tx timestamp
ptp4l: increasing tx_timestamp_timeout may correct this issue,
but it is likely caused by a driver bug
ptp4l: port 1: send peer delay response failed
ptp4l: port 1: LISTENING to FAULTY on FAULT_DETECTED (FT_UNSPECIFIED)
ptp4l tests pass when changing the tx-frames from 25 to 1 with ethtool -C option.
It should be fine to set tx-frames default value to 1, so ptp4l will pass by default.
--- drivers/net/ethernet/stmicro/stmmac/common.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/stmicro/stmmac/common.h +1 -1
@@ -261,7 +261,7 @@ struct stmmac_safety_stats {#define STMMAC_COAL_TX_TIMER 1000#define STMMAC_MAX_COAL_TX_TICK 100000#define STMMAC_TX_MAX_FRAMES 256 -#define STMMAC_TX_FRAMES 25 +#define STMMAC_TX_FRAMES 1/* Packets types */ enum packets_types {
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 66/371 crypto: inside-secure - do not rely on the hardware last bit for result descriptors
In reply to Greg Kroah-Hartman[ Upstream commit 89332590427235680236b9470e851afc49b3caa1 ]
When performing a transformation the hardware is given result descriptors to save the result data. Those result descriptors are batched using a 'first' and a 'last' bit. There are cases were more descriptors than needed are given to the engine, leading to the engine only using some of them, and not setting the last bit on the last descriptor we gave. This causes issues were the driver and the hardware aren't in sync anymore about the number of result descriptors given (as the driver do not give a pool of descriptor to use for any transformation, but a pool of descriptors to use *per* transformation).
This patch fixes it by attaching the number of given result descriptors to the requests, and by using this number instead of the 'last' bit found on the descriptors to process them.
--- .../crypto/inside-secure/safexcel_cipher.c | 24 ++++++++++++++----- 1 file changed, 18 insertions(+), 6 deletions(-)
drivers/crypto/inside-secure/safexcel_cipher.c +18 -6
@@ -51,6 +51,8 @@ struct safexcel_cipher_ctx {struct safexcel_cipher_req {enum safexcel_cipher_direction direction; +/* Number of result descriptors associated to the request */ +unsigned int rdescs;bool needs_inv; };
@@ -333,7 +335,10 @@ static int safexcel_handle_req_result(struct safexcel_crypto_priv *priv, int rin *ret =0 ; - do { +if (unlikely (!sreq->rdescs)) +return 0 ; + +while (sreq->rdescs--) { rdesc =safexcel_ring_next_rptr (priv, &priv->ring[ring].rdr);if (IS_ERR (rdesc)) { dev_err(priv->dev,
@@ -346,7 +351,7 @@ static int safexcel_handle_req_result(struct safexcel_crypto_priv *priv, int rin *ret =safexcel_rdesc_check_errors (priv, rdesc); ndesc++; - }while (!rdesc->last_seg); + }safexcel_complete (priv, ring);
@@ -501,6 +506,7 @@ static int safexcel_send_req(struct crypto_async_request *base, int ring,static int safexcel_handle_inv_result (struct safexcel_crypto_priv *priv,int ring,struct crypto_async_request *base, +struct safexcel_cipher_req *sreq,bool *should_complete,int *ret) {struct safexcel_cipher_ctx *ctx =crypto_tfm_ctx (base->tfm);
@@ -509,7 +515,10 @@ static int safexcel_handle_inv_result(struct safexcel_crypto_priv *priv, *ret =0 ; - do { +if (unlikely (!sreq->rdescs)) +return 0 ; + +while (sreq->rdescs--) { rdesc =safexcel_ring_next_rptr (priv, &priv->ring[ring].rdr);if (IS_ERR (rdesc)) { dev_err(priv->dev,
@@ -522,7 +531,7 @@ static int safexcel_handle_inv_result(struct safexcel_crypto_priv *priv, *ret =safexcel_rdesc_check_errors (priv, rdesc); ndesc++; - }while (!rdesc->last_seg); + }safexcel_complete (priv, ring);
@@ -564,7 +573,7 @@ static int safexcel_skcipher_handle_result(struct safexcel_crypto_priv *priv,if (sreq->needs_inv) { sreq->needs_inv = false; - err =safexcel_handle_inv_result (priv, ring, async, + err =safexcel_handle_inv_result (priv, ring, async, sreq, should_complete, ret); }else { err = safexcel_handle_req_result(priv, ring, async, req->src,
@@ -587,7 +596,7 @@ static int safexcel_aead_handle_result(struct safexcel_crypto_priv *priv,if (sreq->needs_inv) { sreq->needs_inv = false; - err =safexcel_handle_inv_result (priv, ring, async, + err =safexcel_handle_inv_result (priv, ring, async, sreq, should_complete, ret); }else { err = safexcel_handle_req_result(priv, ring, async, req->src,
@@ -633,6 +642,8 @@ static int safexcel_skcipher_send(struct crypto_async_request *async, int ring, ret =safexcel_send_req (async, ring, sreq, req->src, req->dst, req->cryptlen,0 ,0 , req->iv, commands, results); + + sreq->rdescs = *results;return ret; }
@@ -655,6 +666,7 @@ static int safexcel_aead_send(struct crypto_async_request *async, int ring, req->cryptlen, req->assoclen,crypto_aead_authsize (tfm), req->iv, commands, results); + sreq->rdescs = *results;return ret; }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 67/371 net: fec: Do not use netdev messages too early
In reply to Greg Kroah-Hartman[ Upstream commit a19a0582363b9a5f8ba812f34f1b8df394898780 ]
When a valid MAC address is not found the current messages are shown:
fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00 fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: aa:9f:25:eb:7e:aa
Since the network device has not been registered at this point, it is better to use dev_err()/dev_info() instead, which will provide cleaner log messages like these:
fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00 fec 2188000.ethernet: Using random MAC address: aa:9f:25:eb:7e:aa
Tested on a imx6dl-pico-pi board.
--- drivers/net/ethernet/freescale/fec_main.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/net/ethernet/freescale/fec_main.c +3 -3
@@ -1689,10 +1689,10 @@ static void fec_get_mac(struct net_device *ndev)*/ if (!is_valid_ether_addr (iap)) {/* Report it and use a random ethernet address instead */ -netdev_err (ndev,"Invalid MAC address: %pM\n" , iap); +dev_err (&fep->pdev->dev,"Invalid MAC address: %pM\n" , iap);eth_hw_addr_random (ndev); -netdev_info (ndev,"Using random MAC address: %pM\n" , - ndev->dev_addr); +dev_info (&fep->pdev->dev,"Using random MAC address: %pM\n" , + ndev->dev_addr);return ; }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 68/371 net: axienet: Fix race condition causing TX hang
In reply to Greg Kroah-Hartman[ Upstream commit 7de44285c1f69ccfbe8be1d6a16fcd956681fee6 ]
It is possible that the interrupt handler fires and frees up space in the TX ring in between checking for sufficient TX ring space and stopping the TX queue in axienet_start_xmit. If this happens, the queue wake from the interrupt handler will occur before the queue is stopped, causing a lost wakeup and the adapter's transmit hanging.
To avoid this, after stopping the queue, check again whether there is sufficient space in the TX ring. If so, wake up the queue again.
--- .../net/ethernet/xilinx/xilinx_axienet_main.c | 20 ++++++++++++++++--- 1 file changed, 17 insertions(+), 3 deletions(-)
drivers/net/ethernet/xilinx/xilinx_axienet_main.c +17 -3
@@ -614,6 +614,10 @@ static void axienet_start_xmit_done(struct net_device *ndev) ndev->stats.tx_packets += packets; ndev->stats.tx_bytes += size; + +/* Matches barrier in axienet_start_xmit */ +smp_mb (); +netif_wake_queue (ndev); }
@@ -669,9 +673,19 @@ axienet_start_xmit(struct sk_buff *skb, struct net_device *ndev) cur_p = &lp->tx_bd_v[lp->tx_bd_tail];if (axienet_check_tx_bd_space (lp, num_frag)) { -if (!netif_queue_stopped (ndev)) -netif_stop_queue (ndev); -return NETDEV_TX_BUSY ; +if (netif_queue_stopped (ndev)) +return NETDEV_TX_BUSY ; + +netif_stop_queue (ndev); + +/* Matches barrier in axienet_start_xmit_done */ +smp_mb (); + +/* Space might have just been freed - check again */ +if (axienet_check_tx_bd_space (lp, num_frag)) +return NETDEV_TX_BUSY ; + +netif_wake_queue (ndev); }if (skb->ip_summed ==CHECKSUM_PARTIAL ) {
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 69/371 s390/qdio: handle PENDING state for QEBSM devices
In reply to Greg Kroah-Hartman[ Upstream commit 04310324c6f482921c071444833e70fe861b73d9 ]
When a CQ-enabled device uses QEBSM for SBAL state inspection, get_buf_states() can return the PENDING state for an Output Queue. get_outbound_buffer_frontier() isn't prepared for this, and any PENDING buffer will permanently stall all further completion processing on this Queue.
This isn't a concern for non-QEBSM devices, as get_buf_states() for such devices will manually turn PENDING buffers into EMPTY ones.
--- drivers/s390/cio/qdio_main.c | 1 + 1 file changed, 1 insertion(+)
drivers/s390/cio/qdio_main.c +1 -0
@@ -738,6 +738,7 @@ static int get_outbound_buffer_frontier(struct qdio_q *q)switch (state) {case SLSB_P_OUTPUT_EMPTY : +case SLSB_P_OUTPUT_PENDING :/* the adapter got it */ DBF_DEV_EVENT (DBF_INFO , q->irq_ptr,"out empty:%1d %02x" , q->nr, count);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 70/371 RAS/CEC: Fix pfn insertion
In reply to Greg Kroah-Hartman[ Upstream commit 6d8e294bf5f0e85c34e8b14b064e2965f53f38b0 ]
When inserting random PFNs for debugging the CEC through (debugfs)/ras/cec/pfn, depending on the return value of pfn_set(), multiple values get inserted per a single write.
That is because simple_attr_write() interprets a retval of 0 as success and claims the whole input. However, pfn_set() returns the cec_add_elem() value, which, if > 0 and smaller than the whole input length, makes glibc continue issuing the write syscall until there's input left:
pfn_set
simple_attr_write
debugfs_attr_write
full_proxy_write
vfs_write
ksys_write
do_syscall_64
entry_SYSCALL_64_after_hwframe
leading to those repeated calls.
Return 0 to fix that.
--- drivers/ras/cec.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/ras/cec.c +3 -1
@@ -369,7 +369,9 @@ static int pfn_set(void *data, u64 val) { *(u64 *)data = val; -return cec_add_elem (val); +cec_add_elem (val); + +return 0 ; }DEFINE_DEBUGFS_ATTRIBUTE (pfn_ops, u64_get, pfn_set,"0x%llx\n" );
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 71/371 net: sfp: add mutex to prevent concurrent state checks
In reply to Greg Kroah-Hartman[ Upstream commit 2158e856f56bb762ef90f3ec244d41a519826f75 ]
sfp_check_state can potentially be called by both a threaded IRQ handler and delayed work. If it is concurrently called, it could result in incorrect state management. Add a st_mutex to protect the state - this lock gets taken outside of code that checks and handle state changes, and the existing sm_mutex nests inside of it.
--- drivers/net/phy/sfp.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/net/phy/sfp.c +5 -1
@@ -186,10 +186,11 @@ struct sfp {struct gpio_desc *gpio[GPIO_MAX ];bool attached; +struct mutex st_mutex;/* Protects state */ unsigned int state;struct delayed_work poll;struct delayed_work timeout; -struct mutex sm_mutex; +struct mutex sm_mutex;/* Protects state machine */ unsigned char sm_mod_state;unsigned char sm_dev_state;unsigned short sm_state;
@@ -1719,6 +1720,7 @@ static void sfp_check_state(struct sfp *sfp) {unsigned int state, i, changed; +mutex_lock (&sfp->st_mutex); state =sfp_get_state (sfp); changed = state ^ sfp->state; changed &=SFP_F_PRESENT |SFP_F_LOS |SFP_F_TX_FAULT ;
@@ -1744,6 +1746,7 @@ static void sfp_check_state(struct sfp *sfp)sfp_sm_event (sfp, state &SFP_F_LOS ?SFP_E_LOS_HIGH :SFP_E_LOS_LOW );rtnl_unlock (); +mutex_unlock (&sfp->st_mutex); }static irqreturn_t sfp_irq (int irq,void *data)
@@ -1774,6 +1777,7 @@ static struct sfp *sfp_alloc(struct device *dev) sfp->dev = dev;mutex_init (&sfp->sm_mutex); +mutex_init (&sfp->st_mutex);INIT_DELAYED_WORK (&sfp->poll, sfp_poll);INIT_DELAYED_WORK (&sfp->timeout, sfp_timeout);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 72/371 ipset: Fix memory accounting for hash types on resize
In reply to Greg Kroah-Hartman[ Upstream commit 11921796f4799ca9c61c4b22cc54d84aa69f8a35 ]
If a fresh array block is allocated during resize, the current in-memory set size should be increased by the size of the block, not replaced by it.
Before the fix, adding entries to a hash set type, leading to a table resize, caused an inconsistent memory size to be reported. This becomes more obvious when swapping sets with similar sizes:
# cat hash_ip_size.sh #!/bin/sh FAIL_RETRIES=10
tries=0
while [ ${tries} -lt ${FAIL_RETRIES} ]; do
ipset create t1 hash:ip
for i in `seq 1 4345`; do
ipset add t1 1.2.$((i / 255)).$((i % 255))
done
t1_init="$(ipset list t1|sed -n 's/Size in memory: \(.*\)/\1/p')"
ipset create t2 hash:ip
for i in `seq 1 4360`; do
ipset add t2 1.2.$((i / 255)).$((i % 255))
done
t2_init="$(ipset list t2|sed -n 's/Size in memory: \(.*\)/\1/p')"
ipset swap t1 t2
t1_swap="$(ipset list t1|sed -n 's/Size in memory: \(.*\)/\1/p')"
t2_swap="$(ipset list t2|sed -n 's/Size in memory: \(.*\)/\1/p')"
ipset destroy t1
ipset destroy t2
tries=$((tries + 1))
if [ ${t1_init} -lt 10000 ] || [ ${t2_init} -lt 10000 ]; then
echo "FAIL after ${tries} tries:"
echo "T1 size ${t1_init}, after swap ${t1_swap}"
echo "T2 size ${t2_init}, after swap ${t2_swap}"
exit 1
fi
done
echo "PASS"
# echo -n 'func hash_ip4_resize +p' > /sys/kernel/debug/dynamic_debug/control
# ./hash_ip_size.sh
[ 2035.018673] attempt to resize set t1 from 10 to 11, t 00000000fe6551fa
[ 2035.078583] set t1 resized from 10 (00000000fe6551fa) to 11 (00000000172a0163)
[ 2035.080353] Table destroy by resize 00000000fe6551fa
FAIL after 4 tries:
T1 size 9064, after swap 71128
T2 size 71128, after swap 9064--- net/netfilter/ipset/ip_set_hash_gen.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
net/netfilter/ipset/ip_set_hash_gen.h +1 -1
@@ -625,7 +625,7 @@ mtype_resize(struct ip_set *set, bool retried) goto cleanup; } m->size =AHASH_INIT_SIZE ; - extsize =ext_size (AHASH_INIT_SIZE , dsize); + extsize +=ext_size (AHASH_INIT_SIZE , dsize);RCU_INIT_POINTER (hbucket (t, key), m); }else if (m->pos >= m->size) {struct hbucket *ht;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 73/371 perf cs-etm: Properly set the value of old and head in snapshot mode
In reply to Greg Kroah-Hartman[ Upstream commit e45c48a9a4d20ebc7b639a62c3ef8f4b08007027 ]
This patch adds the necessary intelligence to properly compute the value of 'old' and 'head' when operating in snapshot mode. That way we can get the latest information in the AUX buffer and be compatible with the generic AUX ring buffer mechanic.
Tester notes:
Quoted 1 line
Leo, have you had the chance to test/review this one? Suzuki?
Sure. I applied this patch on the perf/core branch (with latest commit 3e4fbf36c1e3 'perf augmented_raw_syscalls: Move reading filename to the loop') and passed testing with below steps:
# perf record -e cs_etm/@tmc_etr0/ -S -m,64 --per-thread ./sort & [1] 19097 Bubble sorting array of 30000 elements
# kill -USR2 19097 # kill -USR2 19097 # kill -USR2 19097 [ perf record: Woken up 4 times to write data ] [ perf record: Captured and wrote 0.753 MB perf.data ]
--- tools/perf/arch/arm/util/cs-etm.c | 127 +++++++++++++++++++++++++++++- 1 file changed, 123 insertions(+), 4 deletions(-)
tools/perf/arch/arm/util/cs-etm.c +123 -4
@@ -31,6 +31,8 @@ struct cs_etm_recording {struct auxtrace_record itr;struct perf_pmu *cs_etm_pmu;struct perf_evlist *evlist; +int wrapped_cnt; +bool *wrapped;bool snapshot_mode;size_t snapshot_size; };
@@ -536,16 +538,131 @@ static int cs_etm_info_fill(struct auxtrace_record *itr,return 0 ; } -static int cs_etm_find_snapshot (struct auxtrace_record *itr__maybe_unused , +static int cs_etm_alloc_wrapped_array (struct cs_etm_recording *ptr,int idx) +{ +bool *wrapped; +int cnt = ptr->wrapped_cnt; + +/* Make @ptr->wrapped as big as @idx */ +while (cnt <= idx) + cnt++; + +/* +* Free'ed in cs_etm_recording_free(). Using realloc() to avoid +* cross compilation problems where the host's system supports +* reallocarray() but not the target. +*/ + wrapped =realloc (ptr->wrapped, cnt *sizeof (bool )); +if (!wrapped) +return -ENOMEM ; + + wrapped[cnt -1 ] = false; + ptr->wrapped_cnt = cnt; + ptr->wrapped = wrapped; + +return 0 ; +} + +static bool cs_etm_buffer_has_wrapped (unsigned char *buffer, +size_t buffer_size,u64 head) +{ +u64 i, watermark; +u64 *buf = (u64 *)buffer; +size_t buf_size = buffer_size; + +/* +* We want to look the very last 512 byte (chosen arbitrarily) in +* the ring buffer. +*/ + watermark = buf_size -512 ; + +/* +* @head is continuously increasing - if its value is equal or greater +* than the size of the ring buffer, it has wrapped around. +*/ +if (head >= buffer_size) +return true; + +/* +* The value of @head is somewhere within the size of the ring buffer. +* This can be that there hasn't been enough data to fill the ring +* buffer yet or the trace time was so long that @head has numerically +* wrapped around. To find we need to check if we have data at the very +* end of the ring buffer. We can reliably do this because mmap'ed +* pages are zeroed out and there is a fresh mapping with every new +* session. +*/ + +/* @head is less than 512 byte from the end of the ring buffer */ +if (head > watermark) + watermark = head; + +/* +* Speed things up by using 64 bit transactions (see "u64 *buf" above) +*/ + watermark >>=3 ; + buf_size >>=3 ; + +/* +* If we find trace data at the end of the ring buffer, @head has +* been there and has numerically wrapped around at least once. +*/ +for (i = watermark; i < buf_size; i++) +if (buf[i]) +return true; + +return false; +} + +static int cs_etm_find_snapshot (struct auxtrace_record *itr,int idx,struct auxtrace_mmap *mm, -unsigned char *data__maybe_unused , +unsigned char *data,u64 *head,u64 *old) { +int err; +bool wrapped; +struct cs_etm_recording *ptr = + container_of(itr, struct cs_etm_recording, itr); + +/* +* Allocate memory to keep track of wrapping if this is the first +* time we deal with this *mm. +*/ +if (idx >= ptr->wrapped_cnt) { + err =cs_etm_alloc_wrapped_array (ptr, idx); +if (err) +return err; + } + +/* +* Check to see if *head has wrapped around. If it hasn't only the +* amount of data between *head and *old is snapshot'ed to avoid +* bloating the perf.data file with zeros. But as soon as *head has +* wrapped around the entire size of the AUX ring buffer it taken. +*/ + wrapped = ptr->wrapped[idx]; +if (!wrapped &&cs_etm_buffer_has_wrapped (data, mm->len, *head)) { + wrapped = true; + ptr->wrapped[idx] = true; + } +pr_debug3 ("%s: mmap index %d old head %zu new head %zu size %zu\n" , __func__, idx, (size_t )*old, (size_t )*head, mm->len); - *old = *head; - *head += mm->len; +/* No wrap has occurred, we can just use *head and *old. */ +if (!wrapped) +return 0 ; + +/* +* *head has wrapped around - adjust *head and *old to pickup the +* entire content of the AUX buffer. +*/ +if (*head >= mm->len) { + *old = *head - mm->len; + }else { + *head += mm->len; + *old = *head - mm->len; + }return 0 ; }
@@ -586,6 +703,8 @@ static void cs_etm_recording_free(struct auxtrace_record *itr) {struct cs_etm_recording *ptr = container_of(itr, struct cs_etm_recording, itr); + +zfree (&ptr->wrapped);free (ptr); }
Signature · 9 lines
2.20.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Greg Kroah-Hartman
maintainerPATCH 74/371 perf test 6: Fix missing kvm module load for s390
In reply to Greg Kroah-Hartman[ Upstream commit 53fe307dfd309e425b171f6272d64296a54f4dff ]
Command
# perf test -Fv 6
fails with error
running test 100 'kvm-s390:kvm_s390_create_vm' failed to parse
event 'kvm-s390:kvm_s390_create_vm', err -1, str 'unknown tracepoint'
event syntax error: 'kvm-s390:kvm_s390_create_vm'
\___ unknown tracepointwhen the kvm module is not loaded or not built in.
Fix this by adding a valid function which tests if the module is loaded. Loaded modules (or builtin KVM support) have a directory named
/sys/kernel/debug/tracing/events/kvm-s390
for this tracepoint.
Check for existence of this directory.
--- tools/perf/tests/parse-events.c | 27 +++++++++++++++++++++++++++ 1 file changed, 27 insertions(+)
tools/perf/tests/parse-events.c +27 -0
@@ -18,6 +18,32 @@#define PERF_TP_SAMPLE_TYPE (PERF_SAMPLE_RAW | PERF_SAMPLE_TIME | \ PERF_SAMPLE_CPU | PERF_SAMPLE_PERIOD) +#if defined(__s390x__) +/* Return true if kvm module is available and loaded. Test this +* and retun success when trace point kvm_s390_create_vm +* exists. Otherwise this test always fails. +*/ +static bool kvm_s390_create_vm_valid (void ) +{ +char *eventfile; +bool rc = false; + + eventfile =get_events_file ("kvm-s390" ); + +if (eventfile) { +DIR *mydir =opendir (eventfile); + +if (mydir) { + rc = true; +closedir (mydir); + } +put_events_file (eventfile); + } + +return rc; +} +#endif +static int test__checkevent_tracepoint (struct perf_evlist *evlist) {struct perf_evsel *evsel =perf_evlist__first (evlist);
@@ -1642,6 +1668,7 @@ static struct evlist_test test__events[] = { { .name = "kvm-s390:kvm_s390_create_vm", .check = test__checkevent_tracepoint, + .valid = kvm_s390_create_vm_valid, .id = 100, }, #endif
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 75/371 perf report: Fix OOM error in TUI mode on s390
In reply to Greg Kroah-Hartman[ Upstream commit 8a07aa4e9b7b0222129c07afff81634a884b2866 ]
Debugging a OOM error using the TUI interface revealed this issue on s390:
[tmricht@m83lp54 perf]$ cat /proc/kallsyms |sort
....00000001119b7158 B radix_tree_node_cachep 00000001119b8000 B __bss_stop00000001119b8000 B _end000003ff80002850 t autofs_mount [autofs4]000003ff80002868 t autofs_show_options [autofs4]000003ff80002a98 t autofs_evict_inode [autofs4]
....
There is a huge gap between the last kernel symbol __bss_stop/_end and the first kernel module symbol autofs_mount (from autofs4 module).
After reading the kernel symbol table via functions:
dso__load()
+--> dso__load_kernel_sym()
+--> dso__load_kallsyms()
+--> __dso_load_kallsyms()
+--> symbols__fixup_end()the symbol __bss_stop has a start address of 1119b8000 and an end address of 3ff80002850, as can be seen by this debug statement:
symbols__fixup_end __bss_stop start:0x1119b8000 end:0x3ff80002850
The size of symbol __bss_stop is 0x3fe6e64a850 bytes! It is the last kernel symbol and fills up the space until the first kernel module symbol.
This size kills the TUI interface when executing the following code:
process_sample_event()
hist_entry_iter__add()
hist_iter__report_callback()
hist_entry__inc_addr_samples()
symbol__inc_addr_samples(symbol = __bss_stop)
symbol__cycles_hist()
annotated_source__alloc_histograms(...,
symbol__size(sym),
...)This function allocates memory to save sample histograms. The symbol_size() marco is defined as sym->end - sym->start, which results in above value of 0x3fe6e64a850 bytes and
the call to calloc() in annotated_source__alloc_histograms() fails.
The histgram memory allocation might fail, make this failure no-fatal and continue processing.
Output before:
[tmricht@m83lp54 perf]$ ./perf --debug stderr=1 report -vvvvv \ -i ~/slow.data 2>/tmp/2 [tmricht@m83lp54 perf]$ tail -5 /tmp/2 __symbol__inc_addr_samples(875): ENOMEM! sym->name=__bss_stop, start=0x1119b8000, addr=0x2aa0005eb08, end=0x3ff80002850, func: 0
problem adding hist entry, skipping event0x938b8 [0x8]: failed to process type: 68 [Cannot allocate memory] [tmricht@m83lp54 perf]$
Output after:
[tmricht@m83lp54 perf]$ ./perf --debug stderr=1 report -vvvvv \ -i ~/slow.data 2>/tmp/2
[tmricht@m83lp54 perf]$ tail -5 /tmp/2
symbol__inc_addr_samples map:0x1597830 start:0x110730000 end:0x3ff80002850 symbol__hists notes->src:0x2aa2a70 nr_hists:1 symbol__inc_addr_samples sym:unlink_anon_vmas src:0x2aa2a70 __symbol__inc_addr_samples: addr=0x11094c69e
0x11094c670 unlink_anon_vmas: period++ [addr: 0x11094c69e, 0x2e, evidx=0]
=> nr_samples: 1, period: 526008
[tmricht@m83lp54 perf]$
There is no error about failed memory allocation and the TUI interface shows all entries.
--- tools/perf/util/annotate.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-)
tools/perf/util/annotate.c +2 -3
@@ -932,9 +932,8 @@ static int symbol__inc_addr_samples(struct symbol *sym, struct map *map,if (sym ==NULL )return 0 ; src =symbol__hists (sym, evsel->evlist->nr_entries); -if (src ==NULL ) -return -ENOMEM ; -return __symbol__inc_addr_samples (sym, map, src, evsel->idx, addr, sample); +return (src) ?__symbol__inc_addr_samples (sym, map, src, evsel->idx, + addr, sample) :0 ; } static int symbol__account_cycles(u64 addr, u64 start,
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 76/371 irqchip/meson-gpio: Add support for Meson-G12A SoC
In reply to Greg Kroah-Hartman[ Upstream commit c64a9e804ccf86eb202bfd1c6a8c5233c75a0431 ]
The Meson-G12A SoC uses the same GPIO interrupt controller IP block as the other Meson SoCs, A totle of 100 pins can be spied on, which is the sum of:
- 223:100 undefined (no interrupt)
- 99:97 3 pins on bank GPIOE - 96:77 20 pins on bank GPIOX - 76:61 16 pins on bank GPIOA - 60:53 8 pins on bank GPIOC - 52:37 16 pins on bank BOOT - 36:28 9 pins on bank GPIOH - 27:12 16 pins on bank GPIOZ - 11:0 12 pins in the AO domain
--- drivers/irqchip/irq-meson-gpio.c | 1 + 1 file changed, 1 insertion(+)
drivers/irqchip/irq-meson-gpio.c +1 -0
@@ -73,6 +73,7 @@ static const struct of_device_id meson_irq_gpio_matches[] = { { .compatible = "amlogic,meson-gxbb-gpio-intc", .data = &gxbb_params }, { .compatible = "amlogic,meson-gxl-gpio-intc", .data = &gxl_params }, { .compatible = "amlogic,meson-axg-gpio-intc", .data = &axg_params }, + { .compatible = "amlogic,meson-g12a-gpio-intc", .data = &axg_params }, { } };
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 77/371 media: uvcvideo: Fix access to uninitialized fields on probe error
In reply to Greg Kroah-Hartman[ Upstream commit 11a087f484bf15ff65f0a9f277aa5a61fd07ed2a ]
We need to check whether this work we are canceling actually is initialized.
--- drivers/media/usb/uvc/uvc_ctrl.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/media/usb/uvc/uvc_ctrl.c +3 -1
@@ -2350,7 +2350,9 @@ void uvc_ctrl_cleanup_device(struct uvc_device *dev)struct uvc_entity *entity;unsigned int i; -cancel_work_sync (&dev->async_ctrl.work); +/* Can be uninitialized if we are aborting on probe error. */ +if (dev->async_ctrl.work.func) +cancel_work_sync (&dev->async_ctrl.work);/* Free controls and control mappings for all entities. */ list_for_each_entry (entity, &dev->entities, list) {
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 78/371 media: fdp1: Support M3N and E3 platforms
In reply to Greg Kroah-Hartman[ Upstream commit 4e8c120de9268fc26f583268b9d22e7d37c4595f ]
New Gen3 R-Car platforms incorporate the FDP1 with an updated version register. No code change is required to support these targets, but they will currently report an error stating that the device can not be identified.
Update the driver to match against the new device types.
--- drivers/media/platform/rcar_fdp1.c | 8 ++++++++ 1 file changed, 8 insertions(+)
drivers/media/platform/rcar_fdp1.c +8 -0
@@ -257,6 +257,8 @@ MODULE_PARM_DESC(debug, "activate debug info");#define FD1_IP_H3_ES1 0x02010101#define FD1_IP_M3W 0x02010202#define FD1_IP_H3 0x02010203 +#define FD1_IP_M3N 0x02010204 +#define FD1_IP_E3 0x02010205/* LUTs */ #define FD1_LUT_DIF_ADJ 0x1000
@@ -2365,6 +2367,12 @@ static int fdp1_probe(struct platform_device *pdev)case FD1_IP_H3 :dprintk (fdp1,"FDP1 Version R-Car H3\n" );break ; +case FD1_IP_M3N : +dprintk (fdp1,"FDP1 Version R-Car M3N\n" ); +break ; +case FD1_IP_E3 : +dprintk (fdp1,"FDP1 Version R-Car E3\n" ); +break ;default :dev_err (fdp1->dev,"FDP1 Unidentifiable (0x%08x)\n" , hw_version);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 79/371 iommu: Fix a leak in iommu_insert_resv_region
In reply to Greg Kroah-Hartman[ Upstream commit ad0834dedaa15c3a176f783c0373f836e44b4700 ]
In case we expand an existing region, we unlink this latter and insert the larger one. In that case we should free the original region after the insertion. Also we can immediately return.
--- drivers/iommu/iommu.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-)
drivers/iommu/iommu.c +5 -3
@@ -241,18 +241,21 @@ static int iommu_insert_resv_region(struct iommu_resv_region *new, pos = pos->next; }else if ((start >= a) && (end <= b)) {if (new->type == type) - goto done; +return 0 ;else pos = pos->next; }else {if (new->type == type) {phys_addr_t new_start =min (a, start);phys_addr_t new_end =max (b, end); +int ret;list_del (&entry->list); entry->start = new_start; entry->length = new_end - new_start +1 ; -iommu_insert_resv_region (entry, regions); + ret =iommu_insert_resv_region (entry, regions); +kfree (entry); +return ret; }else { pos = pos->next; }
@@ -265,7 +268,6 @@ static int iommu_insert_resv_region(struct iommu_resv_region *new,return -ENOMEM ;list_add_tail (®ion->list, pos); -done:return 0 ; }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 80/371 gpio: omap: fix lack of irqstatus_raw0 for OMAP4
In reply to Greg Kroah-Hartman[ Upstream commit 64ea3e9094a1f13b96c33244a3fb3a0f45690bd2 ]
Commit 384ebe1c2849 ("gpio/omap: Add DT support to GPIO driver") added the register definition tables to the gpio-omap driver. Subsequently to that commit, commit 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()") added definitions for irqstatus_raw* registers to the legacy OMAP4 definitions, but missed the DT definitions.
This causes an unintentional change of behaviour for the 1.101 errata workaround on OMAP4 platforms. Fix this oversight.
--- drivers/gpio/gpio-omap.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/gpio/gpio-omap.c +2 -0
@@ -1728,6 +1728,8 @@ static struct omap_gpio_reg_offs omap4_gpio_regs = { .clr_dataout = OMAP4_GPIO_CLEARDATAOUT, .irqstatus = OMAP4_GPIO_IRQSTATUS0, .irqstatus2 = OMAP4_GPIO_IRQSTATUS1, + .irqstatus_raw0 = OMAP4_GPIO_IRQSTATUSRAW0, + .irqstatus_raw1 = OMAP4_GPIO_IRQSTATUSRAW1, .irqenable = OMAP4_GPIO_IRQSTATUSSET0, .irqenable2 = OMAP4_GPIO_IRQSTATUSSET1, .set_irqenable = OMAP4_GPIO_IRQSTATUSSET0,
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 81/371 gpio: omap: ensure irq is enabled before wakeup
In reply to Greg Kroah-Hartman[ Upstream commit c859e0d479b3b4f6132fc12637c51e01492f31f6 ]
Documentation states:
NOTE: There must be a correlation between the wake-up enable and interrupt-enable registers. If a GPIO pin has a wake-up configured on it, it must also have the corresponding interrupt enabled (on one of the two interrupt lines).
Ensure that this condition is always satisfied by enabling the detection events after enabling the interrupt, and disabling the detection before disabling the interrupt. This ensures interrupt/wakeup events can not happen until both the wakeup and interrupt enables correlate.
If we do any clearing, clear between the interrupt enable/disable and trigger setting.
--- drivers/gpio/gpio-omap.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-)
drivers/gpio/gpio-omap.c +8 -7
@@ -838,9 +838,9 @@ static void omap_gpio_irq_shutdown(struct irq_data *d)raw_spin_lock_irqsave (&bank->lock, flags); bank->irq_usage &= ~(BIT (offset)); -omap_set_gpio_irqenable (bank, offset,0 ); -omap_clear_gpio_irqstatus (bank, offset);omap_set_gpio_triggering (bank, offset,IRQ_TYPE_NONE ); +omap_clear_gpio_irqstatus (bank, offset); +omap_set_gpio_irqenable (bank, offset,0 );if (!LINE_USED (bank->mod_usage, offset))omap_clear_gpio_debounce (bank, offset);omap_disable_gpio_module (bank, offset);
@@ -876,8 +876,8 @@ static void omap_gpio_mask_irq(struct irq_data *d)unsigned long flags;raw_spin_lock_irqsave (&bank->lock, flags); -omap_set_gpio_irqenable (bank, offset,0 );omap_set_gpio_triggering (bank, offset,IRQ_TYPE_NONE ); +omap_set_gpio_irqenable (bank, offset,0 );raw_spin_unlock_irqrestore (&bank->lock, flags); }
@@ -889,9 +889,6 @@ static void omap_gpio_unmask_irq(struct irq_data *d)unsigned long flags;raw_spin_lock_irqsave (&bank->lock, flags); -if (trigger) -omap_set_gpio_triggering (bank, offset, trigger); -omap_set_gpio_irqenable (bank, offset,1 );/*
@@ -899,9 +896,13 @@ static void omap_gpio_unmask_irq(struct irq_data *d)* is cleared, thus after the handler has run. OMAP4 needs this done * after enabing the interrupt to clear the wakeup status. */ -if (bank->level_mask &BIT (offset)) +if (bank->regs->leveldetect0 && bank->regs->wkup_en && + trigger & (IRQ_TYPE_LEVEL_HIGH |IRQ_TYPE_LEVEL_LOW ))omap_clear_gpio_irqstatus (bank, offset); +if (trigger) +omap_set_gpio_triggering (bank, offset, trigger); +raw_spin_unlock_irqrestore (&bank->lock, flags); }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 82/371 regmap: fix bulk writes on paged registers
In reply to Greg Kroah-Hartman[ Upstream commit db057679de3e9e6a03c1bcd5aee09b0d25fd9f5b ]
On buses like SlimBus and SoundWire which does not support gather_writes yet in regmap, A bulk write on paged register would be silently ignored after programming page.
This is because local variable 'ret' value in regmap_raw_write_impl() gets reset to 0 once page register is written successfully and the code below checks for 'ret' value to be -ENOTSUPP before linearising the write buffer to send to bus->write().
Fix this by resetting the 'ret' value to -ENOTSUPP in cases where gather_writes() is not supported or single register write is not possible.
--- drivers/base/regmap/regmap.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/base/regmap/regmap.c +2 -0
@@ -1642,6 +1642,8 @@ static int _regmap_raw_write_impl(struct regmap *map, unsigned int reg, map->format.reg_bytes + map->format.pad_bytes, val, val_len); + else + ret = -ENOTSUPP ;/* If that didn't work fall back on linearising by hand. */ if (ret == -ENOTSUPP ) {
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 83/371 gpio: omap: Fix lost edge wake-up interrupts
In reply to Greg Kroah-Hartman[ Upstream commit a522f1d0c381c42f3ace13b8bbeeccabdd6d2e5c ]
If an edge interrupt triggers while entering idle just before we save GPIO datain register to saved_datain, the triggered GPIO will not be noticed on wake-up. This is because the saved_datain and GPIO datain are the same on wake-up in omap_gpio_unidle(). Let's fix this by ignoring any pending edge interrupts for saved_datain.
This issue affects only idle states where the GPIO module internal wake-up path is operational. For deeper idle states where the GPIO module gets powered off, Linux generic wakeirqs must be used for the padconf wake-up events with pinctrl-single driver. For examples, please see "interrupts-extended" dts usage in many drivers.
This issue can be somewhat easily reproduced by pinging an idle system with smsc911x Ethernet interface configured IRQ_TYPE_EDGE_FALLING. At some point the smsc911x interrupts will just stop triggering. Also if WLCORE WLAN is used with EDGE interrupt like it's documentation specifies, we can see lost interrupts without this patch.
Note that in the long run we may be able to cancel entering idle by returning an error in gpio_omap_cpu_notifier() on pending interrupts. But let's fix the bug first.
Also note that because of the recent clean-up efforts this patch does not apply directly to older kernels. This does fix a long term issue though, and can be backported as needed.
--- drivers/gpio/gpio-omap.c | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-)
drivers/gpio/gpio-omap.c +11 -1
@@ -1455,7 +1455,7 @@ static void omap_gpio_idle(struct gpio_bank *bank, bool may_lose_context) {struct device *dev = bank->chip.parent;void __iomem *base = bank->base; -u32 nowake; +u32 mask, nowake; bank->saved_datain =readl_relaxed (base + bank->regs->datain);
@@ -1465,6 +1465,16 @@ static void omap_gpio_idle(struct gpio_bank *bank, bool may_lose_context)if (!bank->enabled_non_wakeup_gpios) goto update_gpio_context_count; +/* Check for pending EDGE_FALLING, ignore EDGE_BOTH */ + mask = bank->enabled_non_wakeup_gpios & bank->context.fallingdetect; + mask &= ~bank->context.risingdetect; + bank->saved_datain |= mask; + +/* Check for pending EDGE_RISING, ignore EDGE_BOTH */ + mask = bank->enabled_non_wakeup_gpios & bank->context.risingdetect; + mask &= ~bank->context.fallingdetect; + bank->saved_datain &= ~mask; +if (!may_lose_context) goto update_gpio_context_count;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 84/371 media: davinci: vpif_capture: fix memory leak in vpif_probe()
In reply to Greg Kroah-Hartman[ Upstream commit 64f883cd98c6d43013fb0cea788b63e50ebc068c ]
If vpif_probe() fails on v4l2_device_register() and vpif_probe_complete(), then memory allocated at initialize_vpif() for global vpif_obj.dev[i] become unreleased.
The patch adds deallocation of vpif_obj.dev[i] on the error path.
--- drivers/media/platform/davinci/vpif_capture.c | 16 ++++++++++++++-- 1 file changed, 14 insertions(+), 2 deletions(-)
drivers/media/platform/davinci/vpif_capture.c +14 -2
@@ -1384,6 +1384,14 @@ static int initialize_vpif(void)return err; } +static inline void free_vpif_objs (void ) +{ +int i; + +for (i =0 ; i <VPIF_CAPTURE_MAX_DEVICES ; i++) +kfree (vpif_obj.dev[i]); +} +static int vpif_async_bound (struct v4l2_async_notifier *notifier,struct v4l2_subdev *subdev,struct v4l2_async_subdev *asd)
@@ -1653,7 +1661,7 @@ static __init int vpif_probe(struct platform_device *pdev) err =v4l2_device_register (vpif_dev, &vpif_obj.v4l2_dev);if (err) {v4l2_err (vpif_dev->driver,"Error registering v4l2 device\n" ); - goto cleanup; + goto vpif_free; }while ((res =platform_get_resource (pdev,IORESOURCE_IRQ , res_idx))) {
@@ -1700,7 +1708,9 @@ static __init int vpif_probe(struct platform_device *pdev)"registered sub device %s\n" , subdevdata->name); } -vpif_probe_complete (); + err =vpif_probe_complete (); +if (err) + goto probe_subdev_out; }else { vpif_obj.notifier.ops = &vpif_async_ops; err = v4l2_async_notifier_register(&vpif_obj.v4l2_dev,
@@ -1719,6 +1729,8 @@ static __init int vpif_probe(struct platform_device *pdev)kfree (vpif_obj.sd); vpif_unregister:v4l2_device_unregister (&vpif_obj.v4l2_dev); +vpif_free: +free_vpif_objs (); cleanup:v4l2_async_notifier_cleanup (&vpif_obj.notifier);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 85/371 bpf: silence warning messages in core
In reply to Greg Kroah-Hartman[ Upstream commit aee450cbe482a8c2f6fa5b05b178ef8b8ff107ca ]
Compiling kernel/bpf/core.c with W=1 causes a flood of warnings:
kernel/bpf/core.c:1198:65: warning: initialized field overwritten [-Woverride-init]
1198 | #define BPF_INSN_3_TBL(x, y, z) [BPF_##x | BPF_##y | BPF_##z] = true
| ^~~~kernel/bpf/core.c:1087:2: note: in expansion of macro 'BPF_INSN_3_TBL'
1087 | INSN_3(ALU, ADD, X), \
| ^~~~~~
kernel/bpf/core.c:1202:3: note: in expansion of macro 'BPF_INSN_MAP'
1202 | BPF_INSN_MAP(BPF_INSN_2_TBL, BPF_INSN_3_TBL),
| ^~~~~~~~~~~~kernel/bpf/core.c:1198:65: note: (near initialization for 'public_insntable[12]')
1198 | #define BPF_INSN_3_TBL(x, y, z) [BPF_##x | BPF_##y | BPF_##z] = true
| ^~~~kernel/bpf/core.c:1087:2: note: in expansion of macro 'BPF_INSN_3_TBL'
1087 | INSN_3(ALU, ADD, X), \
| ^~~~~~
kernel/bpf/core.c:1202:3: note: in expansion of macro 'BPF_INSN_MAP'
1202 | BPF_INSN_MAP(BPF_INSN_2_TBL, BPF_INSN_3_TBL),
| ^~~~~~~~~~~~98 copies of the above.
The attached patch silences the warnings, because we *know* we're overwriting the default initializer. That leaves bpf/core.c with only 6 other warnings, which become more visible in comparison.
--- kernel/bpf/Makefile | 1 + 1 file changed, 1 insertion(+)
kernel/bpf/Makefile +1 -0
@@ -1,5 +1,6 @@ # SPDX-License-Identifier: GPL-2.0 obj-y := core.o +CFLAGS_core.o += $(call cc-disable-warning, override-init) obj-$(CONFIG_BPF_SYSCALL) += syscall.o verifier.o inode.o helpers.o tnum.o obj-$(CONFIG_BPF_SYSCALL) += hashtab.o arraymap.o percpu_freelist.o bpf_lru_list.o lpm_trie.o map_in_map.o
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 86/371 media: s5p-mfc: fix reading min scratch buffer size on MFC v6/v7
In reply to Greg Kroah-Hartman[ Upstream commit be22203aec440c1761ce8542c2636ac6c8951e3a ]
MFC v6 and v7 has no register to read min scratch buffer size, so it has to be read conditionally only if hardware supports it. This fixes following NULL pointer exception on SoCs with MFC v6/v7:
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000000 pgd = f25837f9 [00000000] *pgd=bd93d835 Internal error: Oops: 17 [#1] PREEMPT SMP ARM Modules linked in: btmrvl_sdio btmrvl bluetooth mwifiex_sdio mwifiex ecdh_generic ecc Hardware name: SAMSUNG EXYNOS (Flattened Device Tree) PC is at s5p_mfc_get_min_scratch_buf_size+0x30/0x3c LR is at s5p_mfc_get_min_scratch_buf_size+0x28/0x3c
...
[<c074f998>] (s5p_mfc_get_min_scratch_buf_size) from [<c0745bc0>] (s5p_mfc_irq+0x814/0xa5c) [<c0745bc0>] (s5p_mfc_irq) from [<c019a218>] (__handle_irq_event_percpu+0x64/0x3f8) [<c019a218>] (__handle_irq_event_percpu) from [<c019a5d8>] (handle_irq_event_percpu+0x2c/0x7c) [<c019a5d8>] (handle_irq_event_percpu) from [<c019a660>] (handle_irq_event+0x38/0x5c) [<c019a660>] (handle_irq_event) from [<c019ebc4>] (handle_fasteoi_irq+0xc4/0x180) [<c019ebc4>] (handle_fasteoi_irq) from [<c0199270>] (generic_handle_irq+0x24/0x34) [<c0199270>] (generic_handle_irq) from [<c0199888>] (__handle_domain_irq+0x7c/0xec) [<c0199888>] (__handle_domain_irq) from [<c04ac298>] (gic_handle_irq+0x58/0x9c) [<c04ac298>] (gic_handle_irq) from [<c0101ab0>] (__irq_svc+0x70/0xb0)
Exception stack(0xe73ddc60 to 0xe73ddca8)
...
[<c0101ab0>] (__irq_svc) from [<c01967d8>] (console_unlock+0x5a8/0x6a8) [<c01967d8>] (console_unlock) from [<c01981d0>] (vprintk_emit+0x118/0x2d8) [<c01981d0>] (vprintk_emit) from [<c01983b0>] (vprintk_default+0x20/0x28) [<c01983b0>] (vprintk_default) from [<c01989b4>] (printk+0x30/0x54) [<c01989b4>] (printk) from [<c07500b8>] (s5p_mfc_init_decode_v6+0x1d4/0x284) [<c07500b8>] (s5p_mfc_init_decode_v6) from [<c07230d0>] (vb2_start_streaming+0x24/0x150) [<c07230d0>] (vb2_start_streaming) from [<c0724e4c>] (vb2_core_streamon+0x11c/0x15c) [<c0724e4c>] (vb2_core_streamon) from [<c07478b8>] (vidioc_streamon+0x64/0xa0) [<c07478b8>] (vidioc_streamon) from [<c0709640>] (__video_do_ioctl+0x28c/0x45c) [<c0709640>] (__video_do_ioctl) from [<c0709bc8>] (video_usercopy+0x260/0x8a4) [<c0709bc8>] (video_usercopy) from [<c02b3820>] (do_vfs_ioctl+0xb0/0x9fc) [<c02b3820>] (do_vfs_ioctl) from [<c02b41a0>] (ksys_ioctl+0x34/0x58) [<c02b41a0>] (ksys_ioctl) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xe73ddfa8 to 0xe73ddff0) ... ---[ end trace 376cf5ba6e0bee93 ]---
--- drivers/media/platform/s5p-mfc/s5p_mfc.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/media/platform/s5p-mfc/s5p_mfc.c +2 -1
@@ -527,7 +527,8 @@ static void s5p_mfc_handle_seq_done(struct s5p_mfc_ctx *ctx, dev); ctx->mv_count =s5p_mfc_hw_call (dev->mfc_ops, get_mv_count, dev); - ctx->scratch_buf_size =s5p_mfc_hw_call (dev->mfc_ops, +if (FW_HAS_E_MIN_SCRATCH_BUF (dev)) + ctx->scratch_buf_size =s5p_mfc_hw_call (dev->mfc_ops, get_min_scratch_buf_size, dev);if (ctx->img_width ==0 || ctx->img_height ==0 ) ctx->state =MFCINST_ERROR ;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 87/371 selinux: fix empty write to keycreate file
In reply to Greg Kroah-Hartman[ Upstream commit 464c258aa45b09f16aa0f05847ed8895873262d9 ]
When sid == 0 (we are resetting keycreate_sid to the default value), we should skip the KEY__CREATE check.
Before this patch, doing a zero-sized write to /proc/self/keycreate would check if the current task can create unlabeled keys (which would usually fail with -EACCESS and generate an AVC). Now it skips the check and correctly sets the task's keycreate_sid to 0.
Bug report: https://bugzilla.redhat.com/show_bug.cgi?id=1719067
Tested using the reproducer from the report above.
--- security/selinux/hooks.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-)
security/selinux/hooks.c +6 -5
@@ -6269,11 +6269,12 @@ static int selinux_setprocattr(const char *name, void *value, size_t size) }else if (!strcmp (name,"fscreate" )) { tsec->create_sid = sid; }else if (!strcmp (name,"keycreate" )) { - error =avc_has_perm (&selinux_state, - mysid, sid,SECCLASS_KEY ,KEY__CREATE , -NULL ); -if (error) - goto abort_change; +if (sid) { + error =avc_has_perm (&selinux_state, mysid, sid, +SECCLASS_KEY ,KEY__CREATE ,NULL ); +if (error) + goto abort_change; + } tsec->keycreate_sid = sid; }else if (!strcmp (name,"sockcreate" )) { tsec->sockcreate_sid = sid;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 88/371 crypto: testmgr - add some more preemption points
In reply to Greg Kroah-Hartman[ Upstream commit e63e1b0dd0003dc31f73d875907432be3a2abe5d ]
Call cond_resched() after each fuzz test iteration. This avoids stall warnings if fuzz_iterations is set very high for testing purposes.
While we're at it, also call cond_resched() after finishing testing each test vector.
--- crypto/testmgr.c | 6 ++++++ 1 file changed, 6 insertions(+)
crypto/testmgr.c +6 -0
@@ -1050,6 +1050,7 @@ static int test_hash_vec(const char *driver, const struct hash_testvec *vec, req, tsgl, hashstate);if (err)return err; + cond_resched(); } }#endif
@@ -1105,6 +1106,7 @@ static int __alg_test_hash(const struct hash_testvec *vecs, err =test_hash_vec (driver, &vecs[i], i, req, tsgl, hashstate);if (err) goto out; +cond_resched (); } err =0 ; out:
@@ -1346,6 +1348,7 @@ static int test_aead_vec(const char *driver, int enc, &cfg, req, tsgls);if (err)return err; + cond_resched(); } }#endif
@@ -1365,6 +1368,7 @@ static int test_aead(const char *driver, int enc, tsgls);if (err)return err; +cond_resched (); }return 0 ; }
@@ -1679,6 +1683,7 @@ static int test_skcipher_vec(const char *driver, int enc, &cfg, req, tsgls);if (err)return err; + cond_resched(); } }#endif
@@ -1698,6 +1703,7 @@ static int test_skcipher(const char *driver, int enc, tsgls);if (err)return err; +cond_resched (); }return 0 ; }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 89/371 x86/cpu: Add Ice Lake NNPI to Intel family
In reply to Greg Kroah-Hartman[ Upstream commit e32d045cd4ba06b59878323e434bad010e78e658 ]
Add the CPUID model number of Ice Lake Neural Network Processor for Deep Learning Inference (ICL-NNPI) to the Intel family list. Ice Lake NNPI uses model number 0x9D and this will be documented in a future version of Intel Software Development Manual.
--- arch/x86/include/asm/intel-family.h | 1 + 1 file changed, 1 insertion(+)
arch/x86/include/asm/intel-family.h +1 -0
@@ -56,6 +56,7 @@#define INTEL_FAM6_ICELAKE_XEON_D 0x6C#define INTEL_FAM6_ICELAKE_DESKTOP 0x7D#define INTEL_FAM6_ICELAKE_MOBILE 0x7E +#define INTEL_FAM6_ICELAKE_NNPI 0x9D/* "Small Core" Processors (Atom) */
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 90/371 ASoC: meson: axg-tdm: fix sample clock inversion
In reply to Greg Kroah-Hartman[ Upstream commit cb36ff785e868992e96e8b9e5a0c2822b680a9e2 ]
The content of SND_SOC_DAIFMT_FORMAT_MASK is a number, not a bitfield, so the test to check if the format is i2s is wrong. Because of this the clock setting may be wrong. For example, the sample clock gets inverted in DSP B mode, when it should not.
Fix the lrclk invert helper function
--- sound/soc/meson/axg-tdm.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
sound/soc/meson/axg-tdm.h +1 -1
@@ -40,7 +40,7 @@ struct axg_tdm_iface {static inline bool axg_tdm_lrclk_invert (unsigned int fmt) { -return (fmt &SND_SOC_DAIFMT_I2S ) ^ +return ((fmt &SND_SOC_DAIFMT_FORMAT_MASK ) ==SND_SOC_DAIFMT_I2S ) ^ !!(fmt & (SND_SOC_DAIFMT_IB_IF |SND_SOC_DAIFMT_NB_IF )); }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 91/371 rcu: Force inlining of rcu_read_lock()
In reply to Greg Kroah-Hartman[ Upstream commit 6da9f775175e516fc7229ceaa9b54f8f56aa7924 ]
When debugging options are turned on, the rcu_read_lock() function might not be inlined. This results in lockdep's print_lock() function printing "rcu_read_lock+0x0/0x70" instead of rcu_read_lock()'s caller. For example:
[ 10.579995] =============================
[ 10.584033] WARNING: suspicious RCU usage
[ 10.588074] 4.18.0.memcg_v2+ #1 Not tainted
[ 10.593162] -----------------------------
[ 10.597203] include/linux/rcupdate.h:281 Illegal context switch in
RCU read-side critical section!
[ 10.606220]
[ 10.606220] other info that might help us debug this:
[ 10.606220]
[ 10.614280]
[ 10.614280] rcu_scheduler_active = 2, debug_locks = 1
[ 10.620853] 3 locks held by systemd/1:
[ 10.624632] #0: (____ptrval____) (&type->i_mutex_dir_key#5){.+.+}, at: lookup_slow+0x42/0x70
[ 10.633232] #1: (____ptrval____) (rcu_read_lock){....}, at: rcu_read_lock+0x0/0x70
[ 10.640954] #2: (____ptrval____) (rcu_read_lock){....}, at: rcu_read_lock+0x0/0x70These "rcu_read_lock+0x0/0x70" strings are not providing any useful information. This commit therefore forces inlining of the rcu_read_lock() function so that rcu_read_lock()'s caller is instead shown.
--- include/linux/rcupdate.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
include/linux/rcupdate.h +1 -1
@@ -586,7 +586,7 @@ static inline void rcu_preempt_sleep_check(void) { }* read-side critical sections may be preempted and they may also block, but * only when acquiring spinlocks that are subject to priority inheritance. */ -static inline void rcu_read_lock (void ) +static __always_inline void rcu_read_lock(void) {__rcu_read_lock ();__acquire (RCU );
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 92/371 x86/cpufeatures: Add FDP_EXCPTN_ONLY and ZERO_FCS_FDS
In reply to Greg Kroah-Hartman[ Upstream commit cbb99c0f588737ec98c333558922ce47e9a95827 ]
Add the CPUID enumeration for Intel's de-feature bits to accommodate passing these de-features through to kvm guests.
These de-features are (from SDM vol 1, section 8.1.8):
- X86_FEATURE_FDP_EXCPTN_ONLY: If CPUID.(EAX=07H,ECX=0H):EBX[bit 6] = 1, the data pointer (FDP) is updated only for the x87 non-control instructions that incur unmasked x87 exceptions.
- X86_FEATURE_ZERO_FCS_FDS: If CPUID.(EAX=07H,ECX=0H):EBX[bit 13] = 1, the processor deprecates FCS and FDS; it saves each as 0000H.
--- arch/x86/include/asm/cpufeatures.h | 2 ++ 1 file changed, 2 insertions(+)
arch/x86/include/asm/cpufeatures.h +2 -0
@@ -239,12 +239,14 @@#define X86_FEATURE_BMI1 ( 9*32+ 3)/* 1st group bit manipulation extensions */ #define X86_FEATURE_HLE ( 9*32+ 4)/* Hardware Lock Elision */ #define X86_FEATURE_AVX2 ( 9*32+ 5)/* AVX2 instructions */ +#define X86_FEATURE_FDP_EXCPTN_ONLY ( 9*32+ 6)/* "" FPU data pointer updated only on x87 exceptions */ #define X86_FEATURE_SMEP ( 9*32+ 7)/* Supervisor Mode Execution Protection */ #define X86_FEATURE_BMI2 ( 9*32+ 8)/* 2nd group bit manipulation extensions */ #define X86_FEATURE_ERMS ( 9*32+ 9)/* Enhanced REP MOVSB/STOSB instructions */ #define X86_FEATURE_INVPCID ( 9*32+10)/* Invalidate Processor Context ID */ #define X86_FEATURE_RTM ( 9*32+11)/* Restricted Transactional Memory */ #define X86_FEATURE_CQM ( 9*32+12)/* Cache QoS Monitoring */ +#define X86_FEATURE_ZERO_FCS_FDS ( 9*32+13)/* "" Zero out FPU CS and FPU DS */ #define X86_FEATURE_MPX ( 9*32+14)/* Memory Protection Extension */ #define X86_FEATURE_RDT_A ( 9*32+15)/* Resource Director Technology Allocation */ #define X86_FEATURE_AVX512F ( 9*32+16)/* AVX-512 Foundation */
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 93/371 qed: iWARP - Fix tc for MPA ll2 connection
In reply to Greg Kroah-Hartman[ Upstream commit cb94d52b93c74fe1f2595734fabeda9f8ae891ee ]
The driver needs to assign a lossless traffic class for the MPA ll2 connection to ensure no packets are dropped when returning from the driver as they will never be re-transmitted by the peer.
--- drivers/net/ethernet/qlogic/qed/qed_iwarp.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/net/ethernet/qlogic/qed/qed_iwarp.c +2 -0
@@ -2708,6 +2708,8 @@ qed_iwarp_ll2_start(struct qed_hwfn *p_hwfn, data.input.rx_num_desc = n_ooo_bufs *2 ; data.input.tx_num_desc = data.input.rx_num_desc; data.input.tx_max_bds_per_packet =QED_IWARP_MAX_BDS_PER_FPDU ; + data.input.tx_tc =PKT_LB_TC ; + data.input.tx_dest =QED_LL2_TX_DEST_LB ; data.p_connection_handle = &iwarp_info->ll2_mpa_handle; data.input.secondary_queue = true; data.cbs = &cbs;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 94/371 net: hns3: fix for dereferencing before null checking
In reply to Greg Kroah-Hartman[ Upstream commit 757188005f905664b0186b88cf26a7e844190a63 ]
The netdev is dereferenced before null checking in the function hns3_setup_tc.
This patch moves the dereferencing after the null checking.
--- drivers/net/ethernet/hisilicon/hns3/hns3_enet.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/net/ethernet/hisilicon/hns3/hns3_enet.c +5 -2
@@ -1497,12 +1497,12 @@ static void hns3_nic_get_stats64(struct net_device *netdev,static int hns3_setup_tc (struct net_device *netdev,void *type_data) {struct tc_mqprio_qopt_offload *mqprio_qopt = type_data; -struct hnae3_handle *h =hns3_get_handle (netdev); -struct hnae3_knic_private_info *kinfo = &h->kinfo;u8 *prio_tc = mqprio_qopt->qopt.prio_tc_map; +struct hnae3_knic_private_info *kinfo;u8 tc = mqprio_qopt->qopt.num_tc;u16 mode = mqprio_qopt->mode;u8 hw = mqprio_qopt->qopt.hw; +struct hnae3_handle *h;if (!((hw ==TC_MQPRIO_HW_OFFLOAD_TCS && mode ==TC_MQPRIO_MODE_CHANNEL ) || (!hw && tc ==0 )))
@@ -1514,6 +1514,9 @@ static int hns3_setup_tc(struct net_device *netdev, void *type_data)if (!netdev)return -EINVAL ; + h =hns3_get_handle (netdev); + kinfo = &h->kinfo; +return (kinfo->dcb_ops && kinfo->dcb_ops->setup_tc) ? kinfo->dcb_ops->setup_tc (h, tc, prio_tc) : -EOPNOTSUPP ; }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 95/371 net: hns3: fix for skb leak when doing selftest
In reply to Greg Kroah-Hartman[ Upstream commit 8f9eed1a8791b83eb1c54c261d68424717e4111e ]
If hns3_nic_net_xmit does not return NETDEV_TX_BUSY when doing a loopback selftest, the skb is not freed in hns3_clean_tx_ring or hns3_nic_net_xmit, which causes skb not freed problem.
This patch fixes it by freeing skb when hns3_nic_net_xmit does not return NETDEV_TX_OK.
--- drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c +4 -2
@@ -241,11 +241,13 @@ static int hns3_lp_run_test(struct net_device *ndev, enum hnae3_loop mode)skb_get (skb); tx_ret =hns3_nic_net_xmit (skb, ndev); -if (tx_ret ==NETDEV_TX_OK ) +if (tx_ret ==NETDEV_TX_OK ) { good_cnt++; -else + }else { +kfree_skb (skb);netdev_err (ndev,"hns3_lb_run_test xmit failed: %d\n" , tx_ret); + } }if (good_cnt !=HNS3_NIC_LB_TEST_PKT_NUM ) { ret_val =HNS3_NIC_LB_TEST_TX_CNT_ERR ;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 96/371 net: hns3: delay ring buffer clearing during reset
In reply to Greg Kroah-Hartman[ Upstream commit 3a30964a2eef6aabd3ab18b979ea0eacf1147731 ]
The driver may not be able to disable the ring through firmware when downing the netdev during reset process, which may cause hardware accessing freed buffer problem.
This patch delays the ring buffer clearing to reset uninit process because hardware will not access the ring buffer after hardware reset is completed.
--- .../net/ethernet/hisilicon/hns3/hns3_enet.c | 19 ++++++++++++++----- 1 file changed, 14 insertions(+), 5 deletions(-)
drivers/net/ethernet/hisilicon/hns3/hns3_enet.c +14 -5
@@ -28,7 +28,7 @@#define hns3_tx_bd_count (S ) DIV_ROUND_UP(S, HNS3_MAX_BD_SIZE)static void hns3_clear_all_ring (struct hnae3_handle *h); -static void hns3_force_clear_all_rx_ring (struct hnae3_handle *h); +static void hns3_force_clear_all_ring (struct hnae3_handle *h);static void hns3_remove_hw_addr (struct net_device *netdev);static const char hns3_driver_name[] ="hns3" ;
@@ -484,7 +484,12 @@ static void hns3_nic_net_down(struct net_device *netdev)/* free irq resources */ hns3_nic_uninit_irq (priv); -hns3_clear_all_ring (priv->ae_handle); +/* delay ring buffer clearing to hns3_reset_notify_uninit_enet +* during reset process, because driver may not be able +* to disable the ring through firmware when downing the netdev. +*/ +if (!hns3_nic_resetting (netdev)) +hns3_clear_all_ring (priv->ae_handle); }static int hns3_nic_net_stop (struct net_device *netdev)
@@ -3737,7 +3742,7 @@ static void hns3_client_uninit(struct hnae3_handle *handle, bool reset)hns3_del_all_fd_rules (netdev, true); -hns3_force_clear_all_rx_ring (handle); +hns3_force_clear_all_ring (handle);hns3_uninit_phy (netdev);
@@ -3909,7 +3914,7 @@ static void hns3_force_clear_rx_ring(struct hns3_enet_ring *ring) } } -static void hns3_force_clear_all_rx_ring (struct hnae3_handle *h) +static void hns3_force_clear_all_ring (struct hnae3_handle *h) {struct net_device *ndev = h->kinfo.netdev;struct hns3_nic_priv *priv =netdev_priv (ndev);
@@ -3917,6 +3922,9 @@ static void hns3_force_clear_all_rx_ring(struct hnae3_handle *h)u32 i;for (i =0 ; i < h->kinfo.num_tqps; i++) { + ring = priv->ring_data[i].ring; +hns3_clear_tx_ring (ring); + ring = priv->ring_data[i + h->kinfo.num_tqps].ring;hns3_force_clear_rx_ring (ring); }
@@ -4145,7 +4153,8 @@ static int hns3_reset_notify_uninit_enet(struct hnae3_handle *handle)return 0 ; } -hns3_force_clear_all_rx_ring (handle); +hns3_clear_all_ring (handle); +hns3_force_clear_all_ring (handle);hns3_nic_uninit_vector_data (priv);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 97/371 block: null_blk: fix race condition for null_del_dev
In reply to Greg Kroah-Hartman[ Upstream commit 7602843fd873cae43a444b83b14dfdd114a9659c ]
Dulicate call of null_del_dev() will trigger null pointer error like below. The reason is a race condition between nullb_device_power_store() and nullb_group_drop_item().
CPU#0 CPU#1
---------------- -----------------
do_rmdir()
Quoted 2 lines
configfs_rmdir()client_drop_item()
>nullb_group_drop_item()
nullb_device_power_store()
>null_del_dev()
>test_and_clear_bit(NULLB_DEV_FL_UP
>null_del_dev()
^^^^^
Duplicated null_dev_dev() triger null pointer error
>clear_bit(NULLB_DEV_FL_UPThe fix could be keep the sequnce of clear NULLB_DEV_FL_UP and null_del_dev().
[ 698.613600] BUG: unable to handle kernel NULL pointer dereference at 0000000000000018 [ 698.613608] #PF error: [normal kernel read fault] [ 698.613611] PGD 0 P4D 0 [ 698.613619] Oops: 0000 [#1] SMP PTI [ 698.613627] CPU: 3 PID: 6382 Comm: rmdir Not tainted 5.0.0+ #35 [ 698.613631] Hardware name: LENOVO 20LJS2EV08/20LJS2EV08, BIOS R0SET33W (1.17 ) 07/18/2018 [ 698.613644] RIP: 0010:null_del_dev+0xc/0x110 [null_blk] [ 698.613649] Code: 00 00 00 5b 41 5c 41 5d 41 5e 41 5f 5d c3 0f 0b eb 97 e8 47 bb 2a e8 0f 1f 80 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 41 54 53 <8b> 77 18 48 89 fb 4c 8b 27 48 c7 c7 40 57 1e c1 e8 bf c7 cb e8 48 [ 698.613654] RSP: 0018:ffffb887888bfde0 EFLAGS: 00010286 [ 698.613659] RAX: 0000000000000000 RBX: ffff9d436d92bc00 RCX: ffff9d43a9184681 [ 698.613663] RDX: ffffffffc11e5c30 RSI: 0000000068be6540 RDI: 0000000000000000 [ 698.613667] RBP: ffffb887888bfdf0 R08: 0000000000000001 R09: 0000000000000000 [ 698.613671] R10: ffffb887888bfdd8 R11: 0000000000000f16 R12: ffff9d436d92bc08 [ 698.613675] R13: ffff9d436d94e630 R14: ffffffffc11e5088 R15: ffffffffc11e5000 [ 698.613680] FS: 00007faa68be6540(0000) GS:ffff9d43d14c0000(0000) knlGS:0000000000000000 [ 698.613685] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 698.613689] CR2: 0000000000000018 CR3: 000000042f70c002 CR4: 00000000003606e0 [ 698.613693] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 698.613697] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 698.613700] Call Trace: [ 698.613712] nullb_group_drop_item+0x50/0x70 [null_blk] [ 698.613722] client_drop_item+0x29/0x40 [ 698.613728] configfs_rmdir+0x1ed/0x300 [ 698.613738] vfs_rmdir+0xb2/0x130 [ 698.613743] do_rmdir+0x1c7/0x1e0 [ 698.613750] __x64_sys_rmdir+0x17/0x20 [ 698.613759] do_syscall_64+0x5a/0x110 [ 698.613768] entry_SYSCALL_64_after_hwframe+0x44/0xa9
--- drivers/block/null_blk_main.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-)
drivers/block/null_blk_main.c +6 -5
@@ -326,11 +326,12 @@ static ssize_t nullb_device_power_store(struct config_item *item,set_bit (NULLB_DEV_FL_CONFIGURED , &dev->flags); dev->power = newp; }else if (dev->power && !newp) { -mutex_lock (&lock); - dev->power = newp; -null_del_dev (dev->nullb); -mutex_unlock (&lock); -clear_bit (NULLB_DEV_FL_UP , &dev->flags); +if (test_and_clear_bit (NULLB_DEV_FL_UP , &dev->flags)) { +mutex_lock (&lock); + dev->power = newp; +null_del_dev (dev->nullb); +mutex_unlock (&lock); + }clear_bit (NULLB_DEV_FL_CONFIGURED , &dev->flags); }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 98/371 blkcg, writeback: dead memcgs shouldnt contribute to writeback ownership arbitration
In reply to Greg Kroah-Hartman[ Upstream commit 6631142229005e1b1c311a09efe9fb3cfdac8559 ]
wbc_account_io() collects information on cgroup ownership of writeback pages to determine which cgroup should own the inode. Pages can stay associated with dead memcgs but we want to avoid attributing IOs to dead blkcgs as much as possible as the association is likely to be stale. However, currently, pages associated with dead memcgs contribute to the accounting delaying and/or confusing the arbitration.
Fix it by ignoring pages associated with dead memcgs.
--- fs/fs-writeback.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-)
fs/fs-writeback.c +7 -1
@@ -714,6 +714,7 @@ void wbc_detach_inode(struct writeback_control *wbc)void wbc_account_io (struct writeback_control *wbc,struct page *page,size_t bytes) { +struct cgroup_subsys_state *css;int id;/*
@@ -725,7 +726,12 @@ void wbc_account_io(struct writeback_control *wbc, struct page *page,if (!wbc->wb)return ; - id =mem_cgroup_css_from_page (page)->id; + css =mem_cgroup_css_from_page (page); +/* dead cgroups shouldn't contribute to inode ownership arbitration */ +if (!(css->flags &CSS_ONLINE )) +return ; + + id = css->id;if (id == wbc->wb_id) { wbc->wb_bytes += bytes;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 99/371 xfrm: fix sa selector validation
In reply to Greg Kroah-Hartman[ Upstream commit b8d6d0079757cbd1b69724cfd1c08e2171c68cee ]
After commit b38ff4075a80, the following command does not work anymore:
$ ip xfrm state add src 10.125.0.2 dst 10.125.0.1 proto esp spi 34 reqid 1 \ mode tunnel enc 'cbc(aes)' 0xb0abdba8b782ad9d364ec81e3a7d82a1 auth-trunc \ 'hmac(sha1)' 0xe26609ebd00acb6a4d51fca13e49ea78a72c73e6 96 flag align4
In fact, the selector is not mandatory, allow the user to provide an empty selector.
--- net/xfrm/xfrm_user.c | 3 +++ 1 file changed, 3 insertions(+)
net/xfrm/xfrm_user.c +3 -0
@@ -166,6 +166,9 @@ static int verify_newsa_info(struct xfrm_usersa_info *p, }switch (p->sel.family) { +case AF_UNSPEC : +break ; +case AF_INET :if (p->sel.prefixlen_d >32 || p->sel.prefixlen_s >32 ) goto out;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 100/371 sched/core: Add __sched tag for io_schedule()
In reply to Greg Kroah-Hartman[ Upstream commit e3b929b0a184edb35531153c5afcaebb09014f9d ]
Non-inline io_schedule() was introduced in:
commit 10ab56434f2f ("sched/core: Separate out io_schedule_prepare() and io_schedule_finish()")
Keep in line with io_schedule_timeout(), otherwise "/proc/<pid>/wchan" will report io_schedule() rather than its callers when waiting for IO.
--- kernel/sched/core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
kernel/sched/core.c +1 -1
@@ -5175,7 +5175,7 @@ long __sched io_schedule_timeout(long timeout) }EXPORT_SYMBOL (io_schedule_timeout); -void io_schedule (void ) +void __sched io_schedule(void) {int token;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 101/371 sched/fair: Fix "runnable_avg_yN_inv" not used warnings
In reply to Greg Kroah-Hartman[ Upstream commit 509466b7d480bc5d22e90b9fbe6122ae0e2fbe39 ]
runnable_avg_yN_inv[] is only used in kernel/sched/pelt.c but was included in several other places because they need other macros all came from kernel/sched/sched-pelt.h which was generated by Documentation/scheduler/sched-pelt. As the result, it causes compilation a lot of warnings,
kernel/sched/sched-pelt.h:4:18: warning: 'runnable_avg_yN_inv' defined but not used [-Wunused-const-variable=] kernel/sched/sched-pelt.h:4:18: warning: 'runnable_avg_yN_inv' defined but not used [-Wunused-const-variable=] kernel/sched/sched-pelt.h:4:18: warning: 'runnable_avg_yN_inv' defined but not used [-Wunused-const-variable=]
...
Silence it by appending the __maybe_unused attribute for it, so all generated variables and macros can still be kept in the same file.
--- Documentation/scheduler/sched-pelt.c | 3 ++- kernel/sched/sched-pelt.h | 2 +- 2 files changed, 3 insertions(+), 2 deletions(-)
Documentation/scheduler/sched-pelt.c +2 -1
@@ -20,7 +20,8 @@ void calc_runnable_avg_yN_inv(void)int i;unsigned int x; -printf ("static const u32 runnable_avg_yN_inv[] = {" ); +/* To silence -Wunused-but-set-variable warnings. */ +printf ("static const u32 runnable_avg_yN_inv[] __maybe_unused = {" );for (i =0 ; i <HALFLIFE ; i++) { x = ((1UL <<32 )-1 )*pow (y, i);
kernel/sched/sched-pelt.h +1 -1
@@ -1,7 +1,7 @@/* SPDX-License-Identifier: GPL-2.0 */ /* Generated by Documentation/scheduler/sched-pelt; do not modify. */ -static const u32 runnable_avg_yN_inv[] = { +static const u32 runnable_avg_yN_inv[]__maybe_unused = {0xffffffff ,0xfa83b2da ,0xf5257d14 ,0xefe4b99a ,0xeac0c6e6 ,0xe5b906e6 ,0xe0ccdeeb ,0xdbfbb796 ,0xd744fcc9 ,0xd2a81d91 ,0xce248c14 ,0xc9b9bd85 ,0xc5672a10 ,0xc12c4cc9 ,0xbd08a39e ,0xb8fbaf46 ,0xb504f333 ,0xb123f581 ,
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 102/371 perf/x86/intel: Disable check_msr for real HW
In reply to Greg Kroah-Hartman[ Upstream commit d0e1a507bdc761a14906f03399d933ea639a1756 ]
Tom Vaden reported false failure of the check_msr() function, because some servers can do POST tracing and enable LBR tracing during bootup.
Kan confirmed that check_msr patch was to fix a bug report in guest, so it's ok to disable it for real HW.
--- arch/x86/events/intel/core.c | 8 ++++++++ 1 file changed, 8 insertions(+)
arch/x86/events/intel/core.c +8 -0
@@ -19,6 +19,7 @@#include <asm/intel-family.h> #include <asm/apic.h> #include <asm/cpu_device_id.h> +#include <asm/hypervisor.h> #include "../perf_event.h"
@@ -3927,6 +3928,13 @@ static bool check_msr(unsigned long msr, u64 mask) {u64 val_old, val_new, val_tmp; +/* +* Disable the check for real HW, so we don't +* mess with potentionaly enabled registers: +*/ +if (hypervisor_is_type (X86_HYPER_NATIVE )) +return true; +/* * Read the current value, change it and read it back to see if it * matches, this is needed to detect certain hardware emulators
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 103/371 perf/x86/intel/uncore: Handle invalid event coding for free-running counter
In reply to Greg Kroah-Hartman[ Upstream commit 543ac280b3576c0009e8c0fcd4d6bfc9978d7bd0 ]
Counting with invalid event coding for free-running counter may cause OOPs, e.g. uncore_iio_free_running_0/event=1/.
Current code only validate the event with free-running event format, event=0xff,umask=0xXY. Non-free-running event format never be checked for the PMU with free-running counters.
Add generic hw_config() to check and reject the invalid event coding for free-running PMU.
--- arch/x86/events/intel/uncore.h | 10 ++++++++++ arch/x86/events/intel/uncore_snbep.c | 1 + 2 files changed, 11 insertions(+)
arch/x86/events/intel/uncore.h +10 -0
@@ -419,6 +419,16 @@ static inline bool is_freerunning_event(struct perf_event *event) (((cfg >>8 ) &0xff ) >=UNCORE_FREERUNNING_UMASK_START ); } +/* Check and reject invalid config */ +static inline int uncore_freerunning_hw_config (struct intel_uncore_box *box, +struct perf_event *event) +{ +if (is_freerunning_event (event)) +return 0 ; + +return -EINVAL ; +} +static inline void uncore_disable_box (struct intel_uncore_box *box) {if (box->pmu->type->ops->disable_box)
arch/x86/events/intel/uncore_snbep.c +1 -0
@@ -3585,6 +3585,7 @@ static struct uncore_event_desc skx_uncore_iio_freerunning_events[] = {static struct intel_uncore_ops skx_uncore_iio_freerunning_ops = { .read_counter = uncore_msr_read_counter, + .hw_config = uncore_freerunning_hw_config, };static struct attribute *skx_uncore_iio_freerunning_formats_attr[] = {
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 104/371 integrity: Fix __integrity_init_keyring() section mismatch
In reply to Greg Kroah-Hartman[ Upstream commit 8c655784e2cf59cb6140759b8b546d98261d1ad9 ]
With gcc-4.6.3:
WARNING: vmlinux.o(.text.unlikely+0x24c64): Section mismatch in reference from the function __integrity_init_keyring() to the function .init.text:set_platform_trusted_keys() The function __integrity_init_keyring() references
the function __init set_platform_trusted_keys().
This is often because __integrity_init_keyring lacks a __init
annotation or the annotation of set_platform_trusted_keys is wrong.
Indeed, if the compiler decides not to inline __integrity_init_keyring(), a warning is issued.
Fix this by adding the missing __init annotation.
--- security/integrity/digsig.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
security/integrity/digsig.c +3 -2
@@ -73,8 +73,9 @@ int integrity_digsig_verify(const unsigned int id, const char *sig, int siglen,return -EOPNOTSUPP ; } -static int __integrity_init_keyring (const unsigned int id,key_perm_t perm, -struct key_restriction *restriction) +static int __init __integrity_init_keyring (const unsigned int id, +key_perm_t perm, +struct key_restriction *restriction) {const struct cred *cred =current_cred ();int err =0 ;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 105/371 x86/atomic: Fix smp_mb__{before,after}_atomic()
In reply to Greg Kroah-Hartman[ Upstream commit 69d927bba39517d0980462efc051875b7f4db185 ]
Recent probing at the Linux Kernel Memory Model uncovered a 'surprise'. Strongly ordered architectures where the atomic RmW primitive implies full memory ordering and smp_mb__{before,after}_atomic() are a simple barrier() (such as x86) fail for:
*x = 1; atomic_inc(u); smp_mb__after_atomic(); r0 = *y;
Because, while the atomic_inc() implies memory order, it (surprisingly) does not provide a compiler barrier. This then allows the compiler to re-order like so:
atomic_inc(u); *x = 1; smp_mb__after_atomic(); r0 = *y;
Which the CPU is then allowed to re-order (under TSO rules) like:
atomic_inc(u); r0 = *y; *x = 1;
And this very much was not intended. Therefore strengthen the atomic RmW ops to include a compiler barrier.
NOTE: atomic_{or,and,xor} and the bitops already had the compiler barrier.
--- Documentation/atomic_t.txt | 3 +++ arch/x86/include/asm/atomic.h | 8 ++++---- arch/x86/include/asm/atomic64_64.h | 8 ++++---- arch/x86/include/asm/barrier.h | 4 ++-- 4 files changed, 13 insertions(+), 10 deletions(-)
Documentation/atomic_t.txt +3 -0
@@ -177,6 +177,9 @@ These helper barriers exist because architectures have varying implicit ordering on their SMP atomic primitives. For example our TSO architectures provide full ordered atomics and these barriers are no-ops. +NOTE: when the atomic RmW ops are fully ordered, they should also imply a +compiler barrier. + Thus: atomic_fetch_add();
arch/x86/include/asm/atomic.h +4 -4
@@ -54,7 +54,7 @@ static __always_inline void arch_atomic_add(int i, atomic_t *v) { asmvolatile (LOCK_PREFIX "addl %1,%0" :"+m" (v->counter) - :"ir" (i)); + :"ir" (i) :"memory" ); }/**
@@ -68,7 +68,7 @@ static __always_inline void arch_atomic_sub(int i, atomic_t *v) { asmvolatile (LOCK_PREFIX "subl %1,%0" :"+m" (v->counter) - :"ir" (i)); + :"ir" (i) :"memory" ); }/**
@@ -95,7 +95,7 @@ static __always_inline bool arch_atomic_sub_and_test(int i, atomic_t *v) static __always_inline void arch_atomic_inc(atomic_t *v) { asmvolatile (LOCK_PREFIX "incl %0" - :"+m" (v->counter)); + :"+m" (v->counter) ::"memory" ); }#define arch_atomic_inc arch_atomic_inc
@@ -108,7 +108,7 @@ static __always_inline void arch_atomic_inc(atomic_t *v) static __always_inline void arch_atomic_dec(atomic_t *v) { asmvolatile (LOCK_PREFIX "decl %0" - :"+m" (v->counter)); + :"+m" (v->counter) ::"memory" ); }#define arch_atomic_dec arch_atomic_dec
arch/x86/include/asm/atomic64_64.h +4 -4
@@ -45,7 +45,7 @@ static __always_inline void arch_atomic64_add(long i, atomic64_t *v) { asmvolatile (LOCK_PREFIX "addq %1,%0" :"=m" (v->counter) - :"er" (i),"m" (v->counter)); + :"er" (i),"m" (v->counter) :"memory" ); }/**
@@ -59,7 +59,7 @@ static inline void arch_atomic64_sub(long i, atomic64_t *v) { asmvolatile (LOCK_PREFIX "subq %1,%0" :"=m" (v->counter) - :"er" (i),"m" (v->counter)); + :"er" (i),"m" (v->counter) :"memory" ); }/**
@@ -87,7 +87,7 @@ static __always_inline void arch_atomic64_inc(atomic64_t *v) { asmvolatile (LOCK_PREFIX "incq %0" :"=m" (v->counter) - :"m" (v->counter)); + :"m" (v->counter) :"memory" ); }#define arch_atomic64_inc arch_atomic64_inc
@@ -101,7 +101,7 @@ static __always_inline void arch_atomic64_dec(atomic64_t *v) { asmvolatile (LOCK_PREFIX "decq %0" :"=m" (v->counter) - :"m" (v->counter)); + :"m" (v->counter) :"memory" ); }#define arch_atomic64_dec arch_atomic64_dec
arch/x86/include/asm/barrier.h +2 -2
@@ -80,8 +80,8 @@ do { \ })/* Atomic operations are already serializing on x86 */ -#define __smp_mb__before_atomic () barrier() -#define __smp_mb__after_atomic () barrier() +#define __smp_mb__before_atomic () do { } while (0) +#define __smp_mb__after_atomic () do { } while (0)#include <asm-generic/barrier.h>
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 106/371 perf evsel: Make perf_evsel__name() accept a NULL argument
In reply to Greg Kroah-Hartman[ Upstream commit fdbdd7e8580eac9bdafa532746c865644d125e34 ]
In which case it simply returns "unknown", like when it can't figure out the evsel->name value.
This makes this code more robust and fixes a problem in 'perf trace' where a NULL evsel was being passed to a routine that only used the evsel for printing its name when a invalid syscall id was passed.
--- tools/perf/util/evsel.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-)
tools/perf/util/evsel.c +7 -1
@@ -584,6 +584,9 @@ const char *perf_evsel__name(struct perf_evsel *evsel) {char bf[128 ]; +if (!evsel) + goto out_unknown; +if (evsel->name)return evsel->name;
@@ -620,7 +623,10 @@ const char *perf_evsel__name(struct perf_evsel *evsel) evsel->name =strdup (bf); -return evsel->name ?:"unknown" ; +if (evsel->name) +return evsel->name; +out_unknown: +return "unknown" ; }const char *perf_evsel__group_name (struct perf_evsel *evsel)
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 107/371 vhost_net: disable zerocopy by default
In reply to Greg Kroah-Hartman[ Upstream commit 098eadce3c622c07b328d0a43dda379b38cf7c5e ]
Vhost_net was known to suffer from HOL[1] issues which is not easy to fix. Several downstream disable the feature by default. What's more, the datapath was split and datacopy path got the support of batching and XDP support recently which makes it faster than zerocopy part for small packets transmission.
It looks to me that disable zerocopy by default is more appropriate. It cold be enabled by default again in the future if we fix the above issues.
[1] https://patchwork.kernel.org/patch/3787671/
--- drivers/vhost/net.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/vhost/net.c +1 -1
@@ -36,7 +36,7 @@#include "vhost.h" -static int experimental_zcopytx =1 ; +static int experimental_zcopytx =0 ;module_param (experimental_zcopytx, int,0444 );MODULE_PARM_DESC (experimental_zcopytx,"Enable Zero Copy TX;" " 1 -Enable; 0 - Disable" );
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 108/371 iavf: allow null RX descriptors
In reply to Greg Kroah-Hartman[ Upstream commit efa14c3985828da3163f5372137cb64d992b0f79 ]
In some circumstances, the hardware can hand us a null receive descriptor, with no data attached but otherwise valid. Unfortunately, the driver was ill-equipped to handle such an event, and would stop processing packets at that point.
To fix this, use the Descriptor Done bit instead of the size to determine whether or not a descriptor is ready to be processed. Add some checks to allow for unused buffers.
--- drivers/net/ethernet/intel/iavf/iavf_txrx.c | 21 ++++++++++++++++++--- 1 file changed, 18 insertions(+), 3 deletions(-)
drivers/net/ethernet/intel/iavf/iavf_txrx.c +18 -3
@@ -1236,6 +1236,9 @@ static void iavf_add_rx_frag(struct iavf_ring *rx_ring,unsigned int truesize =SKB_DATA_ALIGN (size +iavf_rx_offset (rx_ring));#endif +if (!size) +return ; +skb_add_rx_frag (skb,skb_shinfo (skb)->nr_frags, rx_buffer->page, rx_buffer->page_offset, size, truesize);
@@ -1260,6 +1263,9 @@ static struct iavf_rx_buffer *iavf_get_rx_buffer(struct iavf_ring *rx_ring, {struct iavf_rx_buffer *rx_buffer; +if (!size) +return NULL ; + rx_buffer = &rx_ring->rx_bi[rx_ring->next_to_clean];prefetchw (rx_buffer->page);
@@ -1299,6 +1305,8 @@ static struct sk_buff *iavf_construct_skb(struct iavf_ring *rx_ring,unsigned int headlen;struct sk_buff *skb; +if (!rx_buffer) +return NULL ;/* prefetch first cache line of first page */ prefetch (va);#if L1_CACHE_BYTES <128
@@ -1363,6 +1371,8 @@ static struct sk_buff *iavf_build_skb(struct iavf_ring *rx_ring,#endif struct sk_buff *skb; +if (!rx_buffer) +return NULL ;/* prefetch first cache line of first page */ prefetch (va);#if L1_CACHE_BYTES <128
@@ -1398,6 +1408,9 @@ static struct sk_buff *iavf_build_skb(struct iavf_ring *rx_ring,static void iavf_put_rx_buffer (struct iavf_ring *rx_ring,struct iavf_rx_buffer *rx_buffer) { +if (!rx_buffer) +return ; +if (iavf_can_reuse_rx_page (rx_buffer)) {/* hand second half of page back to the ring */ iavf_reuse_rx_page (rx_ring, rx_buffer);
@@ -1496,11 +1509,12 @@ static int iavf_clean_rx_irq(struct iavf_ring *rx_ring, int budget)* verified the descriptor has been written back. */ dma_rmb (); +#define IAVF_RXD_DD BIT(IAVF_RX_DESC_STATUS_DD_SHIFT) +if (!iavf_test_staterr (rx_desc,IAVF_RXD_DD )) +break ; size = (qword &IAVF_RXD_QW1_LENGTH_PBUF_MASK ) >>IAVF_RXD_QW1_LENGTH_PBUF_SHIFT ; -if (!size) -break ;iavf_trace (clean_rx_irq, rx_ring, rx_desc, skb); rx_buffer =iavf_get_rx_buffer (rx_ring, size);
@@ -1516,7 +1530,8 @@ static int iavf_clean_rx_irq(struct iavf_ring *rx_ring, int budget)/* exit if we failed to retrieve a buffer */ if (!skb) { rx_ring->rx_stats.alloc_buff_failed++; - rx_buffer->pagecnt_bias++; +if (rx_buffer) + rx_buffer->pagecnt_bias++;break ; }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 109/371 ipoib: correcly show a VF hardware address
In reply to Greg Kroah-Hartman[ Upstream commit 64d701c608fea362881e823b666327f5d28d7ffd ]
in the case of IPoIB with SRIOV enabled hardware
ip link show command incorrecly prints
0 instead of a VF hardware address.
Before:
11: ib1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2044 qdisc pfifo_fast state UP mode DEFAULT group default qlen 256
link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
vf 0 MAC 00:00:00:00:00:00, spoof checking off, link-state disable,
trust off, query_rss off
...
After:
11: ib1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2044 qdisc pfifo_fast state UP mode DEFAULT group default qlen 256
link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
vf 0 link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff, spoof checking off, link-state disable, trust off, query_rss off
v1->v2: just copy an address without modifing ifla_vf_mac v2->v3: update the changelog
--- drivers/infiniband/ulp/ipoib/ipoib_main.c | 1 + 1 file changed, 1 insertion(+)
drivers/infiniband/ulp/ipoib/ipoib_main.c +1 -0
@@ -1998,6 +1998,7 @@ static int ipoib_get_vf_config(struct net_device *dev, int vf,return err; ivf->vf = vf; +memcpy (ivf->mac, dev->dev_addr, dev->addr_len);return 0 ; }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 110/371 ASoC: rsnd: fixup mod ID calculation in rsnd_ctu_probe_
In reply to Greg Kroah-Hartman[ Upstream commit ac28ec07ae1c5c1e18ed6855eb105a328418da88 ]
commit c16015f36cc1 ("ASoC: rsnd: add .get_id/.get_id_sub") introduces rsnd_ctu_id which calcualates and gives the main Device id of the CTU by dividing the id by 4. rsnd_mod_id uses this interface to get the CTU main Device id. But this commit forgets to revert the main Device id calcution previously done in rsnd_ctu_probe_ which also divides the id by 4. This path corrects the same to get the correct main Device id.
The issue is observered when rsnd_ctu_probe_ is done for CTU1
--- sound/soc/sh/rcar/ctu.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
sound/soc/sh/rcar/ctu.c +1 -1
@@ -108,7 +108,7 @@ static int rsnd_ctu_probe_(struct rsnd_mod *mod,struct rsnd_dai_stream *io, struct rsnd_priv *priv) { - return rsnd_cmd_attach(io, rsnd_mod_id(mod) / 4); + return rsnd_cmd_attach(io, rsnd_mod_id(mod)); } static void rsnd_ctu_value_init(struct rsnd_dai_stream *io,
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 111/371 bpf: fix callees pruning callers
In reply to Greg Kroah-Hartman[ Upstream commit eea1c227b9e9bad295e8ef984004a9acf12bb68c ]
The commit 7640ead93924 partially resolved the issue of callees incorrectly pruning the callers.
With introduction of bounded loops and jmps_processed heuristic single verifier state may contain multiple branches and calls.
It's possible that new verifier state (for future pruning) will be allocated inside callee. Then callee will exit (still within the same verifier state). It will go back to the caller and there R6-R9 registers will be read and will trigger mark_reg_read. But the reg->live for all frames but the top frame is not set to LIVE_NONE. Hence mark_reg_read will fail to propagate liveness into parent and future walking will incorrectly conclude that the states are equivalent because LIVE_READ is not set. In other words the rule for parent/live should be:
whenever register parentage chain is set the reg->live should be set to LIVE_NONE. is_state_visited logic already follows this rule for spilled registers.
--- kernel/bpf/verifier.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-)
kernel/bpf/verifier.c +6 -5
@@ -6197,17 +6197,18 @@ static int is_state_visited(struct bpf_verifier_env *env, int insn_idx)* the state of the call instruction (with WRITTEN set), and r0 comes * from callee with its full parentage chain, anyway. */ -for (j =0 ; j <= cur->curframe; j++) -for (i = j < cur->curframe ?BPF_REG_6 :0 ; i <BPF_REG_FP ; i++) - cur->frame[j]->regs[i].parent = &new->frame[j]->regs[i];/* clear write marks in current state: the writes we did are not writes * our child did, so they don't screen off its reads from us. * (There are no read marks in current state, because reads always mark * their parent and current state never has children yet. Only * explored_states can get read marks.) */ -for (i =0 ; i <BPF_REG_FP ; i++) - cur->frame[cur->curframe]->regs[i].live =REG_LIVE_NONE ; +for (j =0 ; j <= cur->curframe; j++) { +for (i = j < cur->curframe ?BPF_REG_6 :0 ; i <BPF_REG_FP ; i++) + cur->frame[j]->regs[i].parent = &new->frame[j]->regs[i]; +for (i =0 ; i <BPF_REG_FP ; i++) + cur->frame[j]->regs[i].live =REG_LIVE_NONE ; + }/* all stack frames are accessible from callee, clear them all */ for (j =0 ; j <= cur->curframe; j++) {
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 112/371 PCI: Add missing link delays required by the PCIe spec
In reply to Greg Kroah-Hartman[ Upstream commit c2bf1fc212f7e6f25ace1af8f0b3ac061ea48ba5 ]
Currently Linux does not follow PCIe spec regarding the required delays after reset. A concrete example is a Thunderbolt add-in-card that consists of a PCIe switch and two PCIe endpoints:
+-1b.0-[01-6b]----00.0-[02-6b]--+-00.0-[03]----00.0 TBT controller
+-01.0-[04-36]-- DS hotplug port
+-02.0-[37]----00.0 xHCI controller
\-04.0-[38-6b]-- DS hotplug portThe root port (1b.0) and the PCIe switch downstream ports are all PCIe gen3 so they support 8GT/s link speeds.
We wait for the PCIe hierarchy to enter D3cold (runtime):
pcieport 0000:00:1b.0: power state changed by ACPI to D3cold
When it wakes up from D3cold, according to the PCIe 4.0 section 5.8 the PCIe switch is put to reset and its power is re-applied. This means that we must follow the rules in PCIe 4.0 section 6.6.1.
For the PCIe gen3 ports we are dealing with here, the following applies:
With a Downstream Port that supports Link speeds greater than 5.0 GT/s, software must wait a minimum of 100 ms after Link training completes before sending a Configuration Request to the device immediately below that Port. Software can determine when Link training completes by polling the Data Link Layer Link Active bit or by setting up an associated interrupt (see Section 6.7.3.3).
Translating this into the above topology we would need to do this (DLLLA stands for Data Link Layer Link Active):
pcieport 0000:00:1b.0: wait for 100ms after DLLLA is set before access to 0000:01:00.0 pcieport 0000:02:00.0: wait for 100ms after DLLLA is set before access to 0000:03:00.0 pcieport 0000:02:02.0: wait for 100ms after DLLLA is set before access to 0000:37:00.0
I've instrumented the kernel with additional logging so we can see the actual delays the kernel performs:
pcieport 0000:00:1b.0: power state changed by ACPI to D0
pcieport 0000:00:1b.0: waiting for D3cold delay of 100 ms
pcieport 0000:00:1b.0: waking up bus
pcieport 0000:00:1b.0: waiting for D3hot delay of 10 ms
pcieport 0000:00:1b.0: restoring config space at offset 0x2c (was 0x60, writing 0x60)
...
pcieport 0000:00:1b.0: PME# disabled
pcieport 0000:01:00.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:01:00.0: PME# disabled
pcieport 0000:02:00.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:02:00.0: PME# disabled
pcieport 0000:02:01.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:02:01.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407) pcieport 0000:02:01.0: PME# disabled
pcieport 0000:02:02.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:02:02.0: PME# disabled
pcieport 0000:02:04.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:02:04.0: PME# disabled
pcieport 0000:02:01.0: PME# enabled
pcieport 0000:02:01.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:04.0: PME# enabled
pcieport 0000:02:04.0: waiting for D3hot delay of 10 ms
thunderbolt 0000:03:00.0: restoring config space at offset 0x14 (was 0x0, writing 0x8a040000)
...
thunderbolt 0000:03:00.0: PME# disabled
xhci_hcd 0000:37:00.0: restoring config space at offset 0x10 (was 0x0, writing 0x73f00000)
...
xhci_hcd 0000:37:00.0: PME# disabled
For the switch upstream port (01:00.0) we wait for 100ms but not taking into account the DLLLA requirement. We then wait 10ms for D3hot -> D0 transition of the root port and the two downstream hotplug ports. This means that we deviate from what the spec requires.
Performing the same check for system sleep (s2idle) transitions we can see following when resuming from s2idle:
pcieport 0000:00:1b.0: power state changed by ACPI to D0
pcieport 0000:00:1b.0: restoring config space at offset 0x2c (was 0x60, writing 0x60)
...
pcieport 0000:01:00.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:02:02.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff) pcieport 0000:02:02.0: restoring config space at offset 0x2c (was 0x0, writing 0x0) pcieport 0000:02:01.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff) pcieport 0000:02:04.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff) pcieport 0000:02:02.0: restoring config space at offset 0x28 (was 0x0, writing 0x0) pcieport 0000:02:00.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff) pcieport 0000:02:02.0: restoring config space at offset 0x24 (was 0x10001, writing 0x1fff1) pcieport 0000:02:01.0: restoring config space at offset 0x2c (was 0x0, writing 0x60) pcieport 0000:02:02.0: restoring config space at offset 0x20 (was 0x0, writing 0x73f073f0) pcieport 0000:02:04.0: restoring config space at offset 0x2c (was 0x0, writing 0x60) pcieport 0000:02:01.0: restoring config space at offset 0x28 (was 0x0, writing 0x60) pcieport 0000:02:00.0: restoring config space at offset 0x2c (was 0x0, writing 0x0) pcieport 0000:02:02.0: restoring config space at offset 0x1c (was 0x101, writing 0x1f1) pcieport 0000:02:04.0: restoring config space at offset 0x28 (was 0x0, writing 0x60) pcieport 0000:02:01.0: restoring config space at offset 0x24 (was 0x10001, writing 0x1ff10001) pcieport 0000:02:00.0: restoring config space at offset 0x28 (was 0x0, writing 0x0) pcieport 0000:02:02.0: restoring config space at offset 0x18 (was 0x0, writing 0x373702) pcieport 0000:02:04.0: restoring config space at offset 0x24 (was 0x10001, writing 0x49f12001) pcieport 0000:02:01.0: restoring config space at offset 0x20 (was 0x0, writing 0x73e05c00) pcieport 0000:02:00.0: restoring config space at offset 0x24 (was 0x10001, writing 0x1fff1) pcieport 0000:02:04.0: restoring config space at offset 0x20 (was 0x0, writing 0x89f07400) pcieport 0000:02:01.0: restoring config space at offset 0x1c (was 0x101, writing 0x5151) pcieport 0000:02:00.0: restoring config space at offset 0x20 (was 0x0, writing 0x8a008a00) pcieport 0000:02:02.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020) pcieport 0000:02:04.0: restoring config space at offset 0x1c (was 0x101, writing 0x6161) pcieport 0000:02:01.0: restoring config space at offset 0x18 (was 0x0, writing 0x360402) pcieport 0000:02:00.0: restoring config space at offset 0x1c (was 0x101, writing 0x1f1) pcieport 0000:02:04.0: restoring config space at offset 0x18 (was 0x0, writing 0x6b3802) pcieport 0000:02:02.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407) pcieport 0000:02:00.0: restoring config space at offset 0x18 (was 0x0, writing 0x30302) pcieport 0000:02:01.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020) pcieport 0000:02:04.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020) pcieport 0000:02:00.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020) pcieport 0000:02:01.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407) pcieport 0000:02:04.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407) pcieport 0000:02:00.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407) xhci_hcd 0000:37:00.0: restoring config space at offset 0x10 (was 0x0, writing 0x73f00000)
...
thunderbolt 0000:03:00.0: restoring config space at offset 0x14 (was 0x0, writing 0x8a040000)
This is even worse. None of the mandatory delays are performed. If this would be S3 instead of s2idle then according to PCI FW spec 3.2 section 4.6.8. there is a specific _DSM that allows the OS to skip the delays but this platform does not provide the _DSM and does not go to S3 anyway so no firmware is involved that could already handle these delays.
In this particular Intel Coffee Lake platform these delays are not actually needed because there is an additional delay as part of the ACPI power resource that is used to turn on power to the hierarchy but since that additional delay is not required by any of standards (PCIe, ACPI) it is not present in the Intel Ice Lake, for example where missing the mandatory delays causes pciehp to start tearing down the stack too early (links are not yet trained).
For this reason, change the PCIe portdrv PM resume hooks so that they perform the mandatory delays before the downstream component gets resumed. We perform the delays before port services are resumed because otherwise pciehp might find that the link is not up (even if it is just training) and tears-down the hierarchy.
--- drivers/pci/pci.c | 29 ++++++++++----- drivers/pci/pci.h | 1 + drivers/pci/pcie/portdrv_core.c | 66 +++++++++++++++++++++++++++++++++ 3 files changed, 86 insertions(+), 10 deletions(-)
drivers/pci/pci.c +19 -10
@@ -999,15 +999,10 @@ static void __pci_start_power_transition(struct pci_dev *dev, pci_power_t state)if (state ==PCI_D0 ) {pci_platform_power_transition (dev,PCI_D0 );/* -* Mandatory power management transition delays, see -* PCI Express Base Specification Revision 2.0 Section -* 6.6.1: Conventional Reset. Do not delay for -* devices powered on/off by corresponding bridge, -* because have already delayed for the bridge. +* Mandatory power management transition delays are +* handled in the PCIe portdrv resume hooks. */ if (dev->runtime_d3cold) { -if (dev->d3cold_delay && !dev->imm_ready) -msleep (dev->d3cold_delay);/* * When powering on a bridge from D3cold, the * whole hierarchy may be powered on into
@@ -4581,14 +4576,16 @@ static int pci_pm_reset(struct pci_dev *dev, int probe)return pci_dev_wait (dev,"PM D3->D0" ,PCIE_RESET_READY_POLL_MS ); } +/** -* pcie_wait_for_link - Wait until link is active or inactive +* pcie_wait_for_link_delay - Wait until link is active or inactive * @pdev: Bridge device * @active: waiting for active or inactive? +* @delay: Delay to wait after link has become active (in ms) * * Use this to wait till link becomes active or inactive. */ -bool pcie_wait_for_link (struct pci_dev *pdev,bool active) +bool pcie_wait_for_link_delay (struct pci_dev *pdev,bool active,int delay) {int timeout =1000 ;bool ret;
@@ -4625,13 +4622,25 @@ bool pcie_wait_for_link(struct pci_dev *pdev, bool active) timeout -=10 ; }if (active && ret) -msleep (100 ); +msleep (delay);else if (ret != active)pci_info (pdev,"Data Link Layer Link Active not %s in 1000 msec\n" , active ?"set" :"cleared" );return ret == active; } +/** +* pcie_wait_for_link - Wait until link is active or inactive +* @pdev: Bridge device +* @active: waiting for active or inactive? +* +* Use this to wait till link becomes active or inactive. +*/ +bool pcie_wait_for_link (struct pci_dev *pdev,bool active) +{ +return pcie_wait_for_link_delay (pdev, active,100 ); +} +void pci_reset_secondary_bus (struct pci_dev *dev) {u16 ctrl;
drivers/pci/pci.h +1 -0
@@ -493,6 +493,7 @@ static inline int pci_dev_specific_disable_acs_redir(struct pci_dev *dev)void pcie_do_recovery (struct pci_dev *dev,enum pci_channel_state state,u32 service); +bool pcie_wait_for_link_delay (struct pci_dev *pdev,bool active,int delay);bool pcie_wait_for_link (struct pci_dev *pdev,bool active);#ifdef CONFIG_PCIEASPM void pcie_aspm_init_link_state (struct pci_dev *pdev);
drivers/pci/pcie/portdrv_core.c +66 -0
90 lines not on this page · raw message
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 113/371 net: netsec: initialize tx ring on ndo_open
In reply to Greg Kroah-Hartman[ Upstream commit 39e3622edeffa63c2871153d8743c5825b139968 ]
Since we changed the Tx ring handling and now depends on bit31 to figure out the owner of the descriptor, we should initialize this every time the device goes down-up instead of doing it once on driver init. If the value is not correctly initialized the device won't have any available descriptors
Changes since v1:
- Typo fixes
--- drivers/net/ethernet/socionext/netsec.c | 32 ++++++++++++++----------- 1 file changed, 18 insertions(+), 14 deletions(-)
drivers/net/ethernet/socionext/netsec.c +18 -14
@@ -1029,7 +1029,6 @@ static void netsec_free_dring(struct netsec_priv *priv, int id)static int netsec_alloc_dring (struct netsec_priv *priv,enum ring_id id) {struct netsec_desc_ring *dring = &priv->desc_ring[id]; -int i; dring->vaddr =dma_alloc_coherent (priv->dev,DESC_SZ *DESC_NUM , &dring->desc_dma,GFP_KERNEL );
@@ -1040,19 +1039,6 @@ static int netsec_alloc_dring(struct netsec_priv *priv, enum ring_id id)if (!dring->desc) goto err; -if (id ==NETSEC_RING_TX ) { -for (i =0 ; i <DESC_NUM ; i++) { -struct netsec_de *de; - - de = dring->vaddr + (DESC_SZ * i); -/* de->attr is not going to be accessed by the NIC -* until netsec_set_tx_de() is called. -* No need for a dma_wmb() here -*/ - de->attr =1U <<NETSEC_TX_SHIFT_OWN_FIELD ; - } - } -return 0 ; err:netsec_free_dring (priv, id);
@@ -1060,6 +1046,23 @@ static int netsec_alloc_dring(struct netsec_priv *priv, enum ring_id id)return -ENOMEM ; } +static void netsec_setup_tx_dring (struct netsec_priv *priv) +{ +struct netsec_desc_ring *dring = &priv->desc_ring[NETSEC_RING_TX ]; +int i; + +for (i =0 ; i <DESC_NUM ; i++) { +struct netsec_de *de; + + de = dring->vaddr + (DESC_SZ * i); +/* de->attr is not going to be accessed by the NIC +* until netsec_set_tx_de() is called. +* No need for a dma_wmb() here +*/ + de->attr =1U <<NETSEC_TX_SHIFT_OWN_FIELD ; + } +} +static int netsec_setup_rx_dring (struct netsec_priv *priv) {struct netsec_desc_ring *dring = &priv->desc_ring[NETSEC_RING_RX ];
@@ -1361,6 +1364,7 @@ static int netsec_netdev_open(struct net_device *ndev)pm_runtime_get_sync (priv->dev); +netsec_setup_tx_dring (priv); ret =netsec_setup_rx_dring (priv);if (ret) { netif_err(priv, probe, priv->ndev,
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 114/371 x86/cacheinfo: Fix a -Wtype-limits warning
In reply to Greg Kroah-Hartman[ Upstream commit 1b7aebf0487613033aff26420e32fa2076d52846 ]
cpuinfo_x86.x86_model is an unsigned type, so comparing against zero will generate a compilation warning:
arch/x86/kernel/cpu/cacheinfo.c: In function 'cacheinfo_amd_init_llc_id':
arch/x86/kernel/cpu/cacheinfo.c:662:19: warning: comparison is always true \
due to limited range of data type [-Wtype-limits]
Remove the unnecessary lower bound check.
[ bp: Massage. ]
--- arch/x86/kernel/cpu/cacheinfo.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)
arch/x86/kernel/cpu/cacheinfo.c +1 -2
@@ -658,8 +658,7 @@ void cacheinfo_amd_init_llc_id(struct cpuinfo_x86 *c, int cpu, u8 node_id)if (c->x86 <0x17 ) {/* LLC is at the node level. */ per_cpu (cpu_llc_id, cpu) = node_id; - }else if (c->x86 ==0x17 && - c->x86_model >=0 && c->x86_model <=0x1F ) { + }else if (c->x86 ==0x17 && c->x86_model <=0x1F ) {/* * LLC is at the core complex level. * Core complex ID is ApicId[3] for these processors.
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 115/371 blk-iolatency: only account submitted bios
In reply to Greg Kroah-Hartman[ Upstream commit a3fb01ba5af066521f3f3421839e501bb2c71805 ]
As is, iolatency recognizes done_bio and cleanup as ending paths. If a request is marked REQ_NOWAIT and fails to get a request, the bio is cleaned up via rq_qos_cleanup() and ended in bio_wouldblock_error(). This results in underflowing the inflight counter. Fix this by only accounting bios that were actually submitted.
--- block/blk-iolatency.c | 4 ++++ 1 file changed, 4 insertions(+)
block/blk-iolatency.c +4 -0
@@ -599,6 +599,10 @@ static void blkcg_iolatency_done_bio(struct rq_qos *rqos, struct bio *bio)if (!blkg || !bio_flagged (bio,BIO_TRACKED ))return ; +/* We didn't actually submit this bio, don't account it. */ +if (bio->bi_status ==BLK_STS_AGAIN ) +return ; + iolat =blkg_to_lat (bio->bi_blkg);if (!iolat)return ;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 116/371 ACPICA: Clear status of GPEs on first direct enable
In reply to Greg Kroah-Hartman[ Upstream commit 44758bafa53602f2581a6857bb20b55d4d8ad5b2 ]
ACPI GPEs (other than the EC one) can be enabled in two situations. First, the GPEs with existing _Lxx and _Exx methods are enabled implicitly by ACPICA during system initialization. Second, the GPEs without these methods (like GPEs listed by _PRW objects for wakeup devices) need to be enabled directly by the code that is going to use them (e.g. ACPI power management or device drivers).
In the former case, if the status of a given GPE is set to start with, its handler method (either _Lxx or _Exx) needs to be invoked to take care of the events (possibly) signaled before the GPE was enabled. In the latter case, however, the first caller of acpi_enable_gpe() for a given GPE should not be expected to care about any events that might be signaled through it earlier. In that case, it is better to clear the status of the GPE before enabling it, to prevent stale events from triggering unwanted actions (like spurious system resume, for example).
For this reason, modify acpi_ev_add_gpe_reference() to take an additional boolean argument indicating whether or not the GPE status needs to be cleared when its reference counter changes from zero to one and make acpi_enable_gpe() pass TRUE to it through that new argument.
--- drivers/acpi/acpica/acevents.h | 3 ++- drivers/acpi/acpica/evgpe.c | 8 +++++++- drivers/acpi/acpica/evgpeblk.c | 2 +- drivers/acpi/acpica/evxface.c | 2 +- drivers/acpi/acpica/evxfgpe.c | 2 +- 5 files changed, 12 insertions(+), 5 deletions(-)
drivers/acpi/acpica/acevents.h +2 -1
@@ -69,7 +69,8 @@ acpi_status acpi_ev_mask_gpe(struct acpi_gpe_event_info *gpe_event_info, u8 is_masked);acpi_status -acpi_ev_add_gpe_reference (struct acpi_gpe_event_info *gpe_event_info); +acpi_ev_add_gpe_reference (struct acpi_gpe_event_info *gpe_event_info, +u8 clear_on_enable);acpi_status acpi_ev_remove_gpe_reference (struct acpi_gpe_event_info *gpe_event_info);
drivers/acpi/acpica/evgpe.c +7 -1
@@ -146,6 +146,7 @@ acpi_ev_mask_gpe(struct acpi_gpe_event_info *gpe_event_info, u8 is_masked)* FUNCTION: acpi_ev_add_gpe_reference * * PARAMETERS: gpe_event_info - Add a reference to this GPE +* clear_on_enable - Clear GPE status before enabling it * * RETURN: Status *
@@ -155,7 +156,8 @@ acpi_ev_mask_gpe(struct acpi_gpe_event_info *gpe_event_info, u8 is_masked)******************************************************************************/ acpi_status -acpi_ev_add_gpe_reference (struct acpi_gpe_event_info *gpe_event_info) +acpi_ev_add_gpe_reference (struct acpi_gpe_event_info *gpe_event_info, +u8 clear_on_enable) {acpi_status status =AE_OK ;
@@ -170,6 +172,10 @@ acpi_ev_add_gpe_reference(struct acpi_gpe_event_info *gpe_event_info)/* Enable on first reference */ +if (clear_on_enable) { + (void )acpi_hw_clear_gpe (gpe_event_info); + } + status =acpi_ev_update_gpe_enable_mask (gpe_event_info);if (ACPI_SUCCESS (status)) { status =acpi_ev_enable_gpe (gpe_event_info);
drivers/acpi/acpica/evgpeblk.c +1 -1
@@ -453,7 +453,7 @@ acpi_ev_initialize_gpe_block(struct acpi_gpe_xrupt_info *gpe_xrupt_info,continue ; } - status =acpi_ev_add_gpe_reference (gpe_event_info); + status =acpi_ev_add_gpe_reference (gpe_event_info, FALSE);if (ACPI_FAILURE (status)) { ACPI_EXCEPTION((AE_INFO, status, "Could not enable GPE 0x%02X",
drivers/acpi/acpica/evxface.c +1 -1
@@ -971,7 +971,7 @@ acpi_remove_gpe_handler(acpi_handle gpe_device, ACPI_GPE_DISPATCH_METHOD) || (ACPI_GPE_DISPATCH_TYPE(handler->original_flags) == ACPI_GPE_DISPATCH_NOTIFY)) && handler->originally_enabled) { - (void )acpi_ev_add_gpe_reference (gpe_event_info); + (void )acpi_ev_add_gpe_reference (gpe_event_info, FALSE);if (ACPI_GPE_IS_POLLING_NEEDED (gpe_event_info)) {/* Poll edge triggered GPEs to handle existing events */
drivers/acpi/acpica/evxfgpe.c +1 -1
@@ -108,7 +108,7 @@ acpi_status acpi_enable_gpe(acpi_handle gpe_device, u32 gpe_number)if (gpe_event_info) {if (ACPI_GPE_DISPATCH_TYPE (gpe_event_info->flags) !=ACPI_GPE_DISPATCH_NONE ) { - status =acpi_ev_add_gpe_reference (gpe_event_info); + status =acpi_ev_add_gpe_reference (gpe_event_info, TRUE);if (ACPI_SUCCESS (status) &&ACPI_GPE_IS_POLLING_NEEDED (gpe_event_info)) {
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 117/371 spi: fix ctrl->num_chipselect constraint
In reply to Greg Kroah-Hartman[ Upstream commit f9481b08220d7dc1ff21e296a330ee8b721b44e4 ]
at91sam9g25ek showed the following error at probe:atmel_spi f0000000.spi: Using dma0chan2 (tx) and dma0chan3 (rx) for DMA transfersatmel_spi: probe of f0000000.spi failed with error -22
Commit 0a919ae49223 ("spi: Don't call spi_get_gpio_descs() before device name is set") moved the calling of spi_get_gpio_descs() after ctrl->dev is set,
but didn't move the !ctrl->num_chipselect check. When there are
chip selects in the device tree, the spi-atmel driver lets the
SPI core discover them when registering the SPI master.
The ctrl->num_chipselect is thus expected to be set by spi_get_gpio_descs().
Move the !ctlr->num_chipselect after spi_get_gpio_descs() as it was before the aforementioned commit. While touching this block, get rid of the explicit comparison with 0 and update the commenting style.
--- drivers/spi/spi.c | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-)
drivers/spi/spi.c +7 -5
@@ -2281,11 +2281,6 @@ int spi_register_controller(struct spi_controller *ctlr)if (status)return status; -/* even if it's just one always-selected device, there must -* be at least one chipselect -*/ -if (ctlr->num_chipselect ==0 ) -return -EINVAL ;if (ctlr->bus_num >=0 ) {/* devices with a fixed bus num must check-in with the num */ mutex_lock (&board_lock);
@@ -2356,6 +2351,13 @@ int spi_register_controller(struct spi_controller *ctlr) } } +/* +* Even if it's just one always-selected device, there must +* be at least one chipselect. +*/ +if (!ctlr->num_chipselect) +return -EINVAL ; + status =device_add (&ctlr->dev);if (status <0 ) {/* free bus id */
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 118/371 EDAC/sysfs: Drop device references properly
In reply to Greg Kroah-Hartman[ Upstream commit 7adc05d2dc3af95e4e1534841d58f736262142cd ]
Do put_device() if device_add() fails.
[ bp: do device_del() for the successfully created devices in
edac_create_csrow_objects(), on the unwind path. ]
--- drivers/edac/edac_mc_sysfs.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-)
drivers/edac/edac_mc_sysfs.c +7 -3
@@ -443,7 +443,8 @@ static int edac_create_csrow_objects(struct mem_ctl_info *mci) csrow = mci->csrows[i];if (!nr_pages_per_csrow (csrow))continue ; -put_device (&mci->csrows[i]->dev); + +device_del (&mci->csrows[i]->dev); }return err;
@@ -645,9 +646,11 @@ static int edac_create_dimm_object(struct mem_ctl_info *mci,dev_set_drvdata (&dimm->dev, dimm);pm_runtime_forbid (&mci->dev); - err =device_add (&dimm->dev); + err =device_add (&dimm->dev); +if (err) +put_device (&dimm->dev); -edac_dbg (0 ,"creating rank/dimm device %s\n" ,dev_name (&dimm->dev)); +edac_dbg (0 ,"created rank/dimm device %s\n" ,dev_name (&dimm->dev));return err; }
@@ -928,6 +931,7 @@ int edac_create_sysfs_mci_device(struct mem_ctl_info *mci, err =device_add (&mci->dev);if (err <0 ) {edac_dbg (1 ,"failure: create device %s\n" ,dev_name (&mci->dev)); +put_device (&mci->dev); goto out; }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 119/371 EDAC/sysfs: Fix memory leak when creating a csrow object
In reply to Greg Kroah-Hartman[ Upstream commit 585fb3d93d32dbe89e718b85009f9c322cc554cd ]
In edac_create_csrow_object(), the reference to the object is not released when adding the device to the device hierarchy fails (device_add()). This may result in a memory leak.
--- drivers/edac/edac_mc_sysfs.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-)
drivers/edac/edac_mc_sysfs.c +7 -1
@@ -404,6 +404,8 @@ static inline int nr_pages_per_csrow(struct csrow_info *csrow)static int edac_create_csrow_object (struct mem_ctl_info *mci,struct csrow_info *csrow,int index) { +int err; + csrow->dev.type = &csrow_attr_type; csrow->dev.groups = csrow_dev_groups;device_initialize (&csrow->dev);
@@ -415,7 +417,11 @@ static int edac_create_csrow_object(struct mem_ctl_info *mci,edac_dbg (0 ,"creating (virtual) csrow node %s\n" ,dev_name (&csrow->dev)); -return device_add (&csrow->dev); + err =device_add (&csrow->dev); +if (err) +put_device (&csrow->dev); + +return err; }/* Create a CSROW object under specifed edac_mc_device */
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 120/371 nvme: fix possible io failures when removing multipathed ns
In reply to Greg Kroah-Hartman[ Upstream commit 2181e455612a8db2761eabbf126640552a451e96 ]
When a shared namespace is removed, we call blk_cleanup_queue() when the device can still be accessed as the current path and this can result in submission to a dying queue. Hence, direct_make_request() called by our mpath device may fail (propagating the failure to userspace). Instead, we want to failover this I/O to a different path if one exists. Thus, before we cleanup the request queue, we make sure that the device is cleared from the current path nor it can be selected again as such.
Fix this by:
- clear the ns from the head->list and synchronize rcu to make sure there is no concurrent path search that restores it as the current path
- clear the mpath current path in order to trigger a subsequent path search and sync srcu to wait for any ongoing request submissions
- safely continue to namespace removal and blk_cleanup_queue
--- drivers/nvme/host/core.c | 14 ++++++++------ 1 file changed, 8 insertions(+), 6 deletions(-)
drivers/nvme/host/core.c +8 -6
@@ -3341,6 +3341,14 @@ static void nvme_ns_remove(struct nvme_ns *ns)return ;nvme_fault_inject_fini (ns); + +mutex_lock (&ns->ctrl->subsys->lock); +list_del_rcu (&ns->siblings); +mutex_unlock (&ns->ctrl->subsys->lock); +synchronize_rcu ();/* guarantee not available in head->list */ +nvme_mpath_clear_current_path (ns); +synchronize_srcu (&ns->head->srcu);/* wait for concurrent submissions */ +if (ns->disk && ns->disk->flags &GENHD_FL_UP ) {del_gendisk (ns->disk);blk_cleanup_queue (ns->queue);
@@ -3348,16 +3356,10 @@ static void nvme_ns_remove(struct nvme_ns *ns)blk_integrity_unregister (ns->disk); } -mutex_lock (&ns->ctrl->subsys->lock); -list_del_rcu (&ns->siblings); -nvme_mpath_clear_current_path (ns); -mutex_unlock (&ns->ctrl->subsys->lock); -down_write (&ns->ctrl->namespaces_rwsem);list_del_init (&ns->list);up_write (&ns->ctrl->namespaces_rwsem); -synchronize_srcu (&ns->head->srcu);nvme_mpath_check_last_path (ns);nvme_put_ns (ns); }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 121/371 nvme-pci: properly report state change failure in nvme_reset_work
In reply to Greg Kroah-Hartman[ Upstream commit cee6c269b016ba89c62e34d6bccb103ee2c7de4f ]
If the state change to NVME_CTRL_CONNECTING fails, the dmesg is going to be like:
[ 293.689160] nvme nvme0: failed to mark controller CONNECTING [ 293.689160] nvme nvme0: Removing after probe failure status: 0
Even it prints the first line to indicate the situation, the second line is not proper because the status is 0 which means normally success of the previous operation.
This patch makes it indicate the proper error value when it fails.
[ 25.932367] nvme nvme0: failed to mark controller CONNECTING [ 25.932369] nvme nvme0: Removing after probe failure status: -16
This situation is able to be easily reproduced by:
root@target:~# rmmod nvme && modprobe nvme && rmmod nvme
--- drivers/nvme/host/pci.c | 1 + 1 file changed, 1 insertion(+)
drivers/nvme/host/pci.c +1 -0
@@ -2545,6 +2545,7 @@ static void nvme_reset_work(struct work_struct *work)if (!nvme_change_ctrl_state (&dev->ctrl,NVME_CTRL_CONNECTING )) {dev_warn (dev->ctrl.device,"failed to mark controller CONNECTING\n" ); + result = -EBUSY ; goto out; }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 122/371 nvme-pci: set the errno on ctrl state change error
In reply to Greg Kroah-Hartman[ Upstream commit e71afda49335620e3d9adf56015676db33a3bd86 ]
This patch removes the confusing assignment of the variable result at the time of declaration and sets the value in error cases next to the places where the actual error is happening.
Here we also set the result value to -ENODEV when we fail at the final ctrl state transition in nvme_reset_work(). Without this assignment result will hold 0 from nvme_setup_io_queue() and on failure 0 will be passed to he nvme_remove_dead_ctrl() from final state transition.
--- drivers/nvme/host/pci.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/nvme/host/pci.c +5 -2
@@ -2504,11 +2504,13 @@ static void nvme_reset_work(struct work_struct *work)struct nvme_dev *dev = container_of(work, struct nvme_dev, ctrl.reset_work);bool was_suspend = !!(dev->ctrl.ctrl_config &NVME_CC_SHN_NORMAL ); -int result = -ENODEV ; +int result;enum nvme_ctrl_state new_state =NVME_CTRL_LIVE ; -if (WARN_ON (dev->ctrl.state !=NVME_CTRL_RESETTING )) +if (WARN_ON (dev->ctrl.state !=NVME_CTRL_RESETTING )) { + result = -ENODEV ; goto out; + }/* * If we're called to reset a live controller first shut it down before
@@ -2606,6 +2608,7 @@ static void nvme_reset_work(struct work_struct *work)if (!nvme_change_ctrl_state (&dev->ctrl, new_state)) {dev_warn (dev->ctrl.device,"failed to mark controller state %d\n" , new_state); + result = -ENODEV ; goto out; }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 123/371 lightnvm: pblk: fix freeing of merged pages
In reply to Greg Kroah-Hartman[ Upstream commit 510fd8ea98fcb586c01aef93d87c060a159ac30a ]
bio_add_pc_page() may merge pages when a bio is padded due to a flush. Fix iteration over the bio to free the correct pages in case of a merge.
--- drivers/lightnvm/pblk-core.c | 18 ++++++++++-------- 1 file changed, 10 insertions(+), 8 deletions(-)
drivers/lightnvm/pblk-core.c +10 -8
@@ -323,14 +323,16 @@ void pblk_free_rqd(struct pblk *pblk, struct nvm_rq *rqd, int type)void pblk_bio_free_pages (struct pblk *pblk,struct bio *bio,int off,int nr_pages) { -struct bio_vec bv; -int i; - -WARN_ON (off + nr_pages != bio->bi_vcnt); - -for (i = off; i < nr_pages + off; i++) { - bv = bio->bi_io_vec[i]; -mempool_free (bv.bv_page, &pblk->page_bio_pool); +struct bio_vec *bv; +struct page *page; +int i, e, nbv =0 ; + +for (i =0 ; i < bio->bi_vcnt; i++) { + bv = &bio->bi_io_vec[i]; + page = bv->bv_page; +for (e =0 ; e < bv->bv_len; e +=PBLK_EXPOSED_PAGE_SIZE , nbv++) +if (nbv >= off) +mempool_free (page++, &pblk->page_bio_pool); } }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 124/371 nvme-pci: adjust irq max_vector using num_possible_cpus()
In reply to Greg Kroah-Hartman[ Upstream commit dad77d63903e91a2e97a0c984cabe5d36e91ba60 ]
If the "irq_queues" are greater than num_possible_cpus(), nvme_calc_irq_sets() can have irq set_size for HCTX_TYPE_DEFAULT greater than it can be afforded.
2039 affd->set_size[HCTX_TYPE_DEFAULT] = nrirqs - nr_read_queues;
It might cause a WARN() from the irq_build_affinity_masks() like [1]:
220 if (nr_present < numvecs)
221 WARN_ON(nr_present + nr_others < numvecs);
This patch prevents it from the WARN() by adjusting the max_vector value from the nvme_setup_irqs().
[1] WARN messages when modprobe nvme write_queues=32 poll_queues=0:
root@target:~/nvme# nproc 8 root@target:~/nvme# modprobe nvme write_queues=32 poll_queues=0 [ 17.925326] nvme nvme0: pci function 0000:00:04.0 [ 17.940601] WARNING: CPU: 3 PID: 1030 at kernel/irq/affinity.c:221 irq_create_affinity_masks+0x222/0x330 [ 17.940602] Modules linked in: nvme nvme_core [last unloaded: nvme] [ 17.940605] CPU: 3 PID: 1030 Comm: kworker/u17:4 Tainted: G W 5.1.0+ #156 [ 17.940605] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 [ 17.940608] Workqueue: nvme-reset-wq nvme_reset_work [nvme] [ 17.940609] RIP: 0010:irq_create_affinity_masks+0x222/0x330 [ 17.940611] Code: 4c 8d 4c 24 28 4c 8d 44 24 30 e8 c9 fa ff ff 89 44 24 18 e8 c0 38 fa ff 8b 44 24 18 44 8b 54 24 1c 5a 44 01 d0 41 39 c4 76 02 <0f> 0b 48 89 df 44 01 e5 e8 f1 ce 10 00 48 8b 34 24 44 89 f0 44 01 [ 17.940611] RSP: 0018:ffffc90002277c50 EFLAGS: 00010216 [ 17.940612] RAX: 0000000000000008 RBX: ffff88807ca48860 RCX: 0000000000000000 [ 17.940612] RDX: ffff88807bc03800 RSI: 0000000000000020 RDI: 0000000000000000 [ 17.940613] RBP: 0000000000000001 R08: ffffc90002277c78 R09: ffffc90002277c70 [ 17.940613] R10: 0000000000000008 R11: 0000000000000001 R12: 0000000000000020 [ 17.940614] R13: 0000000000025d08 R14: 0000000000000001 R15: ffff88807bc03800 [ 17.940614] FS: 0000000000000000(0000) GS:ffff88807db80000(0000) knlGS:0000000000000000 [ 17.940616] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 17.940617] CR2: 00005635e583f790 CR3: 000000000240a000 CR4: 00000000000006e0 [ 17.940617] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 17.940618] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 17.940618] Call Trace: [ 17.940622] __pci_enable_msix_range+0x215/0x540 [ 17.940623] ? kernfs_put+0x117/0x160 [ 17.940625] pci_alloc_irq_vectors_affinity+0x74/0x110 [ 17.940626] nvme_reset_work+0xc30/0x1397 [nvme] [ 17.940628] ? __switch_to_asm+0x34/0x70 [ 17.940628] ? __switch_to_asm+0x40/0x70 [ 17.940629] ? __switch_to_asm+0x34/0x70 [ 17.940630] ? __switch_to_asm+0x40/0x70 [ 17.940630] ? __switch_to_asm+0x34/0x70 [ 17.940631] ? __switch_to_asm+0x40/0x70 [ 17.940632] ? nvme_irq_check+0x30/0x30 [nvme] [ 17.940633] process_one_work+0x20b/0x3e0 [ 17.940634] worker_thread+0x1f9/0x3d0 [ 17.940635] ? cancel_delayed_work+0xa0/0xa0 [ 17.940636] kthread+0x117/0x120 [ 17.940637] ? kthread_stop+0xf0/0xf0 [ 17.940638] ret_from_fork+0x3a/0x50 [ 17.940639] ---[ end trace aca8a131361cd42a ]--- [ 17.942124] nvme nvme0: 7/1/0 default/read/poll queues
--- drivers/nvme/host/pci.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/nvme/host/pci.c +5 -1
@@ -2085,6 +2085,7 @@ static int nvme_setup_irqs(struct nvme_dev *dev, unsigned int nr_io_queues) .priv = dev, };unsigned int irq_queues, this_p_queues; +unsigned int nr_cpus =num_possible_cpus ();/* * Poll queues don't need interrupts, but we need at least one IO
@@ -2095,7 +2096,10 @@ static int nvme_setup_irqs(struct nvme_dev *dev, unsigned int nr_io_queues) this_p_queues = nr_io_queues -1 ; irq_queues =1 ; }else { - irq_queues = nr_io_queues - this_p_queues +1 ; +if (nr_cpus < nr_io_queues - this_p_queues) + irq_queues = nr_cpus +1 ; +else + irq_queues = nr_io_queues - this_p_queues +1 ; } dev->io_queues[HCTX_TYPE_POLL ] = this_p_queues;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 125/371 arm64: Do not enable IRQs for ct_user_exit
In reply to Greg Kroah-Hartman[ Upstream commit 9034f6251572a4744597c51dea5ab73a55f2b938 ]
For el0_dbg and el0_error, DAIF bits get explicitly cleared before calling ct_user_exit.
When context tracking is disabled, DAIF gets set (almost) immediately after. When context tracking is enabled, among the first things done is disabling IRQs.
What is actually needed is:
- PSR.D = 0 so the system can be debugged (should be already the case)
- PSR.A = 0 so async error can be handled during context tracking
Do not clear PSR.I in those two locations.
--- arch/arm64/kernel/entry.S | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm64/kernel/entry.S +2 -2
@@ -855,7 +855,7 @@ el0_dbg: mov x1, x25 mov x2, sp bl do_debug_exception - enable_daif + enable_da_f ct_user_exit b ret_to_user el0_inv:
@@ -907,7 +907,7 @@ el0_error_naked: enable_dbg mov x0, sp bl do_serror - enable_daif + enable_da_f ct_user_exit b ret_to_user ENDPROC(el0_error)
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 126/371 ipsec: select crypto ciphers for xfrm_algo
In reply to Greg Kroah-Hartman[ Upstream commit 597179b0ba550bd83fab1a9d57c42a9343c58514 ]
kernelci.org reports failed builds on arc because of what looks like an old missed 'select' statement:
net/xfrm/xfrm_algo.o: In function `xfrm_probe_algs':
xfrm_algo.c:(.text+0x1e8): undefined reference to `crypto_has_ahash'
I don't see this in randconfig builds on other architectures, but it's fairly clear we want to select the hash code for it, like we do for all its other users. As Herbert points out, CRYPTO_BLKCIPHER is also required even though it has not popped up in build tests.
--- net/xfrm/Kconfig | 2 ++ 1 file changed, 2 insertions(+)
net/xfrm/Kconfig +2 -0
@@ -14,6 +14,8 @@ config XFRM_ALGO tristate select XFRM select CRYPTO + select CRYPTO_HASH + select CRYPTO_BLKCIPHER config XFRM_USER tristate "Transformation user configuration interface"
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 127/371 ipvs: defer hook registration to avoid leaks
In reply to Greg Kroah-Hartman[ Upstream commit cf47a0b882a4e5f6b34c7949d7b293e9287f1972 ]
syzkaller reports for memory leak when registering hooks [1]
As we moved the nf_unregister_net_hooks() call into __ip_vs_dev_cleanup(), defer the nf_register_net_hooks() call, so that hooks are allocated and freed from same pernet_operations (ipvs_core_dev_ops).
[1]
BUG: memory leak
unreferenced object 0xffff88810acd8a80 (size 96):
comm "syz-executor073", pid 7254, jiffies 4294950560 (age 22.250s) hex dump (first 32 bytes):
02 00 00 00 00 00 00 00 50 8b bb 82 ff ff ff ff ........P....... 00 00 00 00 00 00 00 00 00 77 bb 82 ff ff ff ff .........w......
backtrace:
[<0000000013db61f1>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline] [<0000000013db61f1>] slab_post_alloc_hook mm/slab.h:439 [inline] [<0000000013db61f1>] slab_alloc_node mm/slab.c:3269 [inline] [<0000000013db61f1>] kmem_cache_alloc_node_trace+0x15b/0x2a0 mm/slab.c:3597 [<000000001a27307d>] __do_kmalloc_node mm/slab.c:3619 [inline] [<000000001a27307d>] __kmalloc_node+0x38/0x50 mm/slab.c:3627 [<0000000025054add>] kmalloc_node include/linux/slab.h:590 [inline] [<0000000025054add>] kvmalloc_node+0x4a/0xd0 mm/util.c:431 [<0000000050d1bc00>] kvmalloc include/linux/mm.h:637 [inline] [<0000000050d1bc00>] kvzalloc include/linux/mm.h:645 [inline] [<0000000050d1bc00>] allocate_hook_entries_size+0x3b/0x60 net/netfilter/core.c:61 [<00000000e8abe142>] nf_hook_entries_grow+0xae/0x270 net/netfilter/core.c:128 [<000000004b94797c>] __nf_register_net_hook+0x9a/0x170 net/netfilter/core.c:337 [<00000000d1545cbc>] nf_register_net_hook+0x34/0xc0 net/netfilter/core.c:464 [<00000000876c9b55>] nf_register_net_hooks+0x53/0xc0 net/netfilter/core.c:480 [<000000002ea868e0>] __ip_vs_init+0xe8/0x170 net/netfilter/ipvs/ip_vs_core.c:2280 [<000000002eb2d451>] ops_init+0x4c/0x140 net/core/net_namespace.c:130 [<000000000284ec48>] setup_net+0xde/0x230 net/core/net_namespace.c:316 [<00000000a70600fa>] copy_net_ns+0xf0/0x1e0 net/core/net_namespace.c:439 [<00000000ff26c15e>] create_new_namespaces+0x141/0x2a0 kernel/nsproxy.c:107 [<00000000b103dc79>] copy_namespaces+0xa1/0xe0 kernel/nsproxy.c:165 [<000000007cc008a2>] copy_process.part.0+0x11fd/0x2150 kernel/fork.c:2035 [<00000000c344af7c>] copy_process kernel/fork.c:1800 [inline] [<00000000c344af7c>] _do_fork+0x121/0x4f0 kernel/fork.c:2369
--- net/netfilter/ipvs/ip_vs_core.c | 21 ++++++++++++++------- 1 file changed, 14 insertions(+), 7 deletions(-)
net/netfilter/ipvs/ip_vs_core.c +14 -7
@@ -2250,7 +2250,6 @@ static const struct nf_hook_ops ip_vs_ops[] = {static int __net_init __ip_vs_init (struct net *net) {struct netns_ipvs *ipvs; -int ret; ipvs =net_generic (net, ip_vs_net_id);if (ipvs ==NULL )
@@ -2282,17 +2281,11 @@ static int __net_init __ip_vs_init(struct net *net)if (ip_vs_sync_net_init (ipvs) <0 ) goto sync_fail; - ret =nf_register_net_hooks (net, ip_vs_ops,ARRAY_SIZE (ip_vs_ops)); -if (ret <0 ) - goto hook_fail; -return 0 ;/* * Error handling */ -hook_fail: -ip_vs_sync_net_cleanup (ipvs); sync_fail:ip_vs_conn_net_cleanup (ipvs); conn_fail:
@@ -2322,6 +2315,19 @@ static void __net_exit __ip_vs_cleanup(struct net *net) net->ipvs =NULL ; } +static int __net_init __ip_vs_dev_init (struct net *net) +{ +int ret; + + ret =nf_register_net_hooks (net, ip_vs_ops,ARRAY_SIZE (ip_vs_ops)); +if (ret <0 ) + goto hook_fail; +return 0 ; + +hook_fail: +return ret; +} + static void __net_exit __ip_vs_dev_cleanup(struct net *net) {struct netns_ipvs *ipvs =net_ipvs (net);
@@ -2341,6 +2347,7 @@ static struct pernet_operations ipvs_core_ops = { };static struct pernet_operations ipvs_core_dev_ops = { + .init = __ip_vs_dev_init, .exit = __ip_vs_dev_cleanup, };
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 128/371 media: s5p-mfc: Make additional clocks optional
In reply to Greg Kroah-Hartman[ Upstream commit e08efef8fe7db87206314c19b341612c719f891a ]
Since the beginning the second clock ('special', 'sclk') was optional and it is not available on some variants of Exynos SoCs (i.e. Exynos5420 with v7 of MFC hardware).
However commit 1bce6fb3edf1 ("[media] s5p-mfc: Rework clock handling") made handling of all specified clocks mandatory. This patch restores original behavior of the driver and fixes its operation on Exynos5420 SoCs.
--- drivers/media/platform/s5p-mfc/s5p_mfc_pm.c | 5 +++++ 1 file changed, 5 insertions(+)
drivers/media/platform/s5p-mfc/s5p_mfc_pm.c +5 -0
@@ -38,6 +38,11 @@ int s5p_mfc_init_pm(struct s5p_mfc_dev *dev)for (i =0 ; i < pm->num_clocks; i++) { pm->clocks[i] =devm_clk_get (pm->device, pm->clk_names[i]);if (IS_ERR (pm->clocks[i])) { +/* additional clocks are optional */ +if (i &&PTR_ERR (pm->clocks[i]) == -ENOENT ) { + pm->clocks[i] =NULL ; +continue ; + }mfc_err ("Failed to get clock: %s\n" , pm->clk_names[i]);return PTR_ERR (pm->clocks[i]);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 129/371 media: i2c: fix warning same module names
In reply to Greg Kroah-Hartman[ Upstream commit b2ce5617dad254230551feda3599f2cc68e53ad8 ]
When building with CONFIG_VIDEO_ADV7511 and CONFIG_DRM_I2C_ADV7511 enabled as loadable modules, we see the following warning:
drivers/gpu/drm/bridge/adv7511/adv7511.ko
drivers/media/i2c/adv7511.ko
Rework so that the file is named adv7511-v4l2.c.
---
drivers/media/i2c/Makefile | 2 +-
drivers/media/i2c/{adv7511.c => adv7511-v4l2.c} | 5 +++++
2 files changed, 6 insertions(+), 1 deletion(-)
rename drivers/media/i2c/{adv7511.c => adv7511-v4l2.c} (99%)drivers/media/i2c/Makefile +1 -1
@@ -35,7 +35,7 @@ obj-$(CONFIG_VIDEO_ADV748X) += adv748x/ obj-$(CONFIG_VIDEO_ADV7604) += adv7604.o obj-$(CONFIG_VIDEO_ADV7842) += adv7842.o obj-$(CONFIG_VIDEO_AD9389B) += ad9389b.o -obj-$(CONFIG_VIDEO_ADV7511) += adv7511.o +obj-$(CONFIG_VIDEO_ADV7511) += adv7511-v4l2.o obj-$(CONFIG_VIDEO_VPX3220) += vpx3220.o obj-$(CONFIG_VIDEO_VS6624) += vs6624.o obj-$(CONFIG_VIDEO_BT819) += bt819.o
drivers/media/i2c/adv7511-v4l2.c renamed from drivers/media/i2c/adv7511.c +5 -0
@@ -5,6 +5,11 @@* Copyright 2013 Cisco Systems, Inc. and/or its affiliates. All rights reserved. */ +/* +* This file is named adv7511-v4l2.c so it doesn't conflict with the Analog +* Device ADV7511 (config fragment CONFIG_DRM_I2C_ADV7511). +*/ +#include <linux/kernel.h> #include <linux/module.h>
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 130/371 ntp: Limit TAI-UTC offset
In reply to Greg Kroah-Hartman[ Upstream commit d897a4ab11dc8a9fda50d2eccc081a96a6385998 ]
Don't allow the TAI-UTC offset of the system clock to be set by adjtimex() to a value larger than 100000 seconds.
This prevents an overflow in the conversion to int, prevents the CLOCK_TAI clock from getting too far ahead of the CLOCK_REALTIME clock, and it is still large enough to allow leap seconds to be inserted at the maximum rate currently supported by the kernel (once per day) for the next ~270 years, however unlikely it is that someone can survive a catastrophic event which slowed down the rotation of the Earth so much.
--- kernel/time/ntp.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
kernel/time/ntp.c +3 -1
@@ -42,6 +42,7 @@ static u64 tick_length_base;#define MAX_TICKADJ 500LL/* usecs */ #define MAX_TICKADJ_SCALED \ (((MAX_TICKADJ * NSEC_PER_USEC) << NTP_SCALE_SHIFT) / NTP_INTERVAL_FREQ) +#define MAX_TAI_OFFSET 100000/* * phase-lock loop variables
@@ -690,7 +691,8 @@ static inline void process_adjtimex_modes(const struct __kernel_timex *txc, time_constant =max (time_constant,0l ); } -if (txc->modes &ADJ_TAI && txc->constant >=0 ) +if (txc->modes &ADJ_TAI && + txc->constant >=0 && txc->constant <=MAX_TAI_OFFSET ) *time_tai = txc->constant;if (txc->modes &ADJ_OFFSET )
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 131/371 timer_list: Guard procfs specific code
In reply to Greg Kroah-Hartman[ Upstream commit a9314773a91a1d3b36270085246a6715a326ff00 ]
With CONFIG_PROC_FS=n the following warning is emitted:
kernel/time/timer_list.c:361:36: warning: unused variable 'timer_list_sops' [-Wunused-const-variable]
static const struct seq_operations timer_list_sops = {
Add #ifdef guard around procfs specific code.
--- kernel/time/timer_list.c | 36 +++++++++++++++++++----------------- 1 file changed, 19 insertions(+), 17 deletions(-)
kernel/time/timer_list.c +19 -17
@@ -282,23 +282,6 @@ static inline void timer_list_header(struct seq_file *m, u64 now)SEQ_printf (m,"\n" ); } -static int timer_list_show (struct seq_file *m,void *v) -{ -struct timer_list_iter *iter = v; - -if (iter->cpu ==-1 && !iter->second_pass) -timer_list_header (m, iter->now); -else if (!iter->second_pass) -print_cpu (m, iter->cpu, iter->now); -#ifdef CONFIG_GENERIC_CLOCKEVENTS - else if (iter->cpu == -1 && iter->second_pass) - timer_list_show_tickdevices_header(m); - else - print_tickdevice(m, tick_get_device(iter->cpu), iter->cpu); -#endif -return 0 ; -} -void sysrq_timer_list_show (void ) {u64 now =ktime_to_ns (ktime_get ());
@@ -317,6 +300,24 @@ void sysrq_timer_list_show(void)return ; } +#ifdef CONFIG_PROC_FS +static int timer_list_show (struct seq_file *m,void *v) +{ +struct timer_list_iter *iter = v; + +if (iter->cpu ==-1 && !iter->second_pass) +timer_list_header (m, iter->now); +else if (!iter->second_pass) +print_cpu (m, iter->cpu, iter->now); +#ifdef CONFIG_GENERIC_CLOCKEVENTS + else if (iter->cpu == -1 && iter->second_pass) + timer_list_show_tickdevices_header(m); + else + print_tickdevice(m, tick_get_device(iter->cpu), iter->cpu); +#endif +return 0 ; +} +static void *move_iter (struct timer_list_iter *iter,loff_t offset) {for (; offset; offset--) {
@@ -376,3 +377,4 @@ static int __init init_timer_list_procfs(void) return 0; }__initcall (init_timer_list_procfs); +#endif
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 132/371 media: mt9m111: fix fw-node refactoring
In reply to Greg Kroah-Hartman[ Upstream commit 8d4e29a51a954b43e06d916772fa4f50b7e5bbd6 ]
In the patch refactoring the fw-node, the mt9m111 was broken for all platform_data based platforms, which were the first aim of this driver. Only the devicetree platform are still functional, probably because the testing was done on these.
The result is that -EINVAL is systematically return for such platforms, what this patch fixes.
[Sakari Ailus: Rework this to resolve a merge conflict and use dev_fwnode]
--- drivers/media/i2c/mt9m111.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-)
drivers/media/i2c/mt9m111.c +5 -3
@@ -1248,9 +1248,11 @@ static int mt9m111_probe(struct i2c_client *client,if (!mt9m111)return -ENOMEM ; - ret =mt9m111_probe_fw (client, mt9m111); -if (ret) -return ret; +if (dev_fwnode (&client->dev)) { + ret =mt9m111_probe_fw (client, mt9m111); +if (ret) +return ret; + } mt9m111->clk =v4l2_clk_get (&client->dev,"mclk" );if (IS_ERR (mt9m111->clk))
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 133/371 ASoC: soc-core: call snd_soc_unbind_card() under mutex_lock;
In reply to Greg Kroah-Hartman[ Upstream commit b545542a0b866f7975254e41c595836e9bc0ff2f ]
commit 34ac3c3eb8f0c07 ("ASoC: core: lock client_mutex while removing link components") added mutex_lock() at soc_remove_link_components().
Is is called from snd_soc_unbind_card()
snd_soc_unbind_card()
=> soc_remove_link_components()
soc_cleanup_card_resources()
soc_remove_dai_links()
=> soc_remove_link_components()
And, there are 2 way to call it.
(1)
snd_soc_unregister_component()
** mutex_lock()
snd_soc_component_del_unlocked()
=> snd_soc_unbind_card()
** mutex_unlock()
(2)
snd_soc_unregister_card()
=> snd_soc_unbind_card()
(1) case is already using mutex_lock() when it calles snd_soc_unbind_card(), thus, we will get lockdep warning.
commit 495f926c68ddb90 ("ASoC: core: Fix deadlock in snd_soc_instantiate_card()") tried to fixup it, but still not enough. We still have lockdep warning when we try unbind/bind.
We need mutex_lock() under snd_soc_unregister_card() instead of snd_remove_link_components()/snd_soc_unbind_card().
--- sound/soc/soc-core.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
sound/soc/soc-core.c +2 -2
@@ -2834,14 +2834,12 @@ static void snd_soc_unbind_card(struct snd_soc_card *card, bool unregister)snd_soc_dapm_shutdown (card);snd_soc_flush_all_delayed_work (card); -mutex_lock (&client_mutex);/* remove all components used by DAI links on this card */ for_each_comp_order (order) {for_each_card_rtds (card, rtd) {soc_remove_link_components (card, rtd, order); } } -mutex_unlock (&client_mutex);soc_cleanup_card_resources (card);if (!unregister)
@@ -2860,7 +2858,9 @@ static void snd_soc_unbind_card(struct snd_soc_card *card, bool unregister)*/ int snd_soc_unregister_card (struct snd_soc_card *card) { +mutex_lock (&client_mutex);snd_soc_unbind_card (card, true); +mutex_unlock (&client_mutex);dev_dbg (card->dev,"ASoC: Unregistered card '%s'\n" , card->name);return 0 ;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 134/371 acpi/arm64: ignore 5.1 FADTs that are reported as 5.0
In reply to Greg Kroah-Hartman[ Upstream commit 2af22f3ec3ca452f1e79b967f634708ff01ced8a ]
Some Qualcomm Snapdragon based laptops built to run Microsoft Windows are clearly ACPI 5.1 based, given that that is the first ACPI revision that supports ARM, and introduced the FADT 'arm_boot_flags' field, which has a non-zero field on those systems.
So in these cases, infer from the ARM boot flags that the FADT must be 5.1 or later, and treat it as 5.1.
--- arch/arm64/kernel/acpi.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-)
arch/arm64/kernel/acpi.c +7 -3
@@ -155,10 +155,14 @@ static int __init acpi_fadt_sanity_check(void)*/ if (table->revision <5 || (table->revision ==5 && fadt->minor_revision <1 )) { -pr_err ("Unsupported FADT revision %d.%d, should be 5.1+\n" , +pr_err (FW_BUG "Unsupported FADT revision %d.%d, should be 5.1+\n" , table->revision, fadt->minor_revision); - ret = -EINVAL ; - goto out; + +if (!fadt->arm_boot_flags) { + ret = -EINVAL ; + goto out; + } +pr_err ("FADT has ARM boot flags set, assuming 5.1\n" ); }if (!(fadt->flags &ACPI_FADT_HW_REDUCED )) {
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 135/371 media: coda: fix mpeg2 sequence number handling
In reply to Greg Kroah-Hartman[ Upstream commit 56d159a4ec6d8da7313aac6fcbb95d8fffe689ba ]
Sequence number handling assumed that the BIT processor frame number starts counting at 1, but this is not true for the MPEG-2 decoder, which starts at 0. Fix the sequence counter offset detection to handle this.
--- drivers/media/platform/coda/coda-bit.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/media/platform/coda/coda-bit.c +4 -1
@@ -1743,6 +1743,7 @@ static int __coda_start_decoding(struct coda_ctx *ctx)v4l2_err (&dev->v4l2_dev,"CODA_COMMAND_SEQ_INIT timeout\n" );return ret; } + ctx->sequence_offset = ~0U ; ctx->initialized =1 ;/* Update kfifo out pointer from coda bitstream read pointer */
@@ -2155,7 +2156,9 @@ static void coda_finish_decode(struct coda_ctx *ctx)v4l2_err (&dev->v4l2_dev,"decoded frame index out of range: %d\n" , decoded_idx); }else { - val =coda_read (dev,CODA_RET_DEC_PIC_FRAME_NUM ) -1 ; + val =coda_read (dev,CODA_RET_DEC_PIC_FRAME_NUM ); +if (ctx->sequence_offset ==-1 ) + ctx->sequence_offset = val; val -= ctx->sequence_offset;spin_lock (&ctx->buffer_meta_lock);if (!list_empty (&ctx->buffer_meta_list)) {
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 136/371 media: coda: fix last buffer handling in V4L2_ENC_CMD_STOP
In reply to Greg Kroah-Hartman[ Upstream commit f3775f89852d167990b0d718587774cf00d22ac2 ]
coda_encoder_cmd() is racy, as the last scheduled picture run worker can still be in-flight while the ENC_CMD_STOP command is issued. Depending on the exact timing the sequence numbers might already be changed, but the last buffer might not have been put on the destination queue yet.
In this case the current implementation would prematurely wake the destination queue with last_buffer_dequeued=true, causing userspace to call streamoff before the last buffer is handled.
Close this race window by synchronizing with the pic_run_worker before doing the sequence check.
--- drivers/media/platform/coda/coda-common.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/media/platform/coda/coda-common.c +2 -0
@@ -1007,6 +1007,8 @@ static int coda_encoder_cmd(struct file *file, void *fh,/* Set the stream-end flag on this context */ ctx->bit_stream_param |=CODA_BIT_STREAM_END_FLAG ; +flush_work (&ctx->pic_run_work); +/* If there is no buffer in flight, wake up */ if (!ctx->streamon_out || ctx->qsequence == ctx->osequence) { dst_vq = v4l2_m2m_get_vq(ctx->fh.m2m_ctx,
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 137/371 media: coda: increment sequence offset for the last returned frame
In reply to Greg Kroah-Hartman[ Upstream commit b3b7d96817cdb8b6fc353867705275dce8f41ccc ]
If no more frames are decoded in bitstream end mode, and a previously decoded frame has been returned, the firmware still increments the frame number. To avoid a sequence number mismatch after decoder restart, increment the sequence_offset correction parameter.
--- drivers/media/platform/coda/coda-bit.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/media/platform/coda/coda-bit.c +3 -0
@@ -2151,6 +2151,9 @@ static void coda_finish_decode(struct coda_ctx *ctx)else if (ctx->display_idx <0 ) ctx->hold = true; }else if (decoded_idx ==-2 ) { +if (ctx->display_idx >=0 && + ctx->display_idx < ctx->num_internal_frames) + ctx->sequence_offset++;/* no frame was decoded, we still return remaining buffers */ }else if (decoded_idx <0 || decoded_idx >= ctx->num_internal_frames) { v4l2_err(&dev->v4l2_dev,
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 138/371 media: vimc: cap: check v4l2_fill_pixfmt return value
In reply to Greg Kroah-Hartman[ Upstream commit 77ae46e11df5c96bb4582633851f838f5d954df4 ]
v4l2_fill_pixfmt() returns -EINVAL if the pixelformat used as parameter is invalid or if the user is trying to use a multiplanar format with the singleplanar API. Currently, the vimc_cap_try_fmt_vid_cap() returns such value, but vimc_cap_s_fmt_vid_cap() is ignoring it. Fix that and returns an error value if vimc_cap_try_fmt_vid_cap() has failed.
--- drivers/media/platform/vimc/vimc-capture.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/media/platform/vimc/vimc-capture.c +4 -1
@@ -130,12 +130,15 @@ static int vimc_cap_s_fmt_vid_cap(struct file *file, void *priv, struct v4l2_format *f) {struct vimc_cap_device *vcap =video_drvdata (file); +int ret;/* Do not change the format while stream is on */ if (vb2_is_busy (&vcap->queue))return -EBUSY ; -vimc_cap_try_fmt_vid_cap (file, priv, f); + ret =vimc_cap_try_fmt_vid_cap (file, priv, f); +if (ret) +return ret;dev_dbg (vcap->dev,"%s: format update: " "old:%dx%d (0x%x, %d, %d, %d, %d) "
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 139/371 media: hdpvr: fix locking and a missing msleep
In reply to Greg Kroah-Hartman[ Upstream commit 6bc5a4a1927556ff9adce1aa95ea408c95453225 ]
This driver has three locking issues:
- The wait_event_interruptible() condition calls hdpvr_get_next_buffer(dev) which uses a mutex, which is not allowed. Rewrite with list_empty_careful() that doesn't need locking.
- In hdpvr_read() the call to hdpvr_stop_streaming() didn't lock io_mutex, but it should have since stop_streaming expects that.
- In hdpvr_device_release() io_mutex was locked when calling flush_work(), but there it shouldn't take that mutex since the work done by flush_work() also wants to lock that mutex.
There are also two other changes (suggested by Keith):
- msecs_to_jiffies(4000); (a NOP) should have been msleep(4000).
- Change v4l2_dbg to v4l2_info to always log if streaming had to be restarted.
--- drivers/media/usb/hdpvr/hdpvr-video.c | 17 +++++++++++------ 1 file changed, 11 insertions(+), 6 deletions(-)
drivers/media/usb/hdpvr/hdpvr-video.c +11 -6
@@ -439,7 +439,7 @@ static ssize_t hdpvr_read(struct file *file, char __user *buffer, size_t count,/* wait for the first buffer */ if (!(file->f_flags &O_NONBLOCK )) {if (wait_event_interruptible (dev->wait_data, -hdpvr_get_next_buffer (dev))) + !list_empty_careful (&dev->rec_buff_list)))return -ERESTARTSYS ; }
@@ -465,10 +465,17 @@ static ssize_t hdpvr_read(struct file *file, char __user *buffer, size_t count, goto err; }if (!err) { -v4l2_dbg (MSG_INFO , hdpvr_debug, &dev->v4l2_dev, -"timeout: restart streaming\n" ); +v4l2_info (&dev->v4l2_dev, +"timeout: restart streaming\n" ); +mutex_lock (&dev->io_mutex);hdpvr_stop_streaming (dev); -msecs_to_jiffies (4000 ); +mutex_unlock (&dev->io_mutex); +/* +* The FW needs about 4 seconds after streaming +* stopped before it is ready to restart +* streaming. +*/ +msleep (4000 ); err =hdpvr_start_streaming (dev);if (err) { ret = err;
@@ -1133,9 +1140,7 @@ static void hdpvr_device_release(struct video_device *vdev)struct hdpvr_device *dev =video_get_drvdata (vdev);hdpvr_delete (dev); -mutex_lock (&dev->io_mutex);flush_work (&dev->worker); -mutex_unlock (&dev->io_mutex);v4l2_device_unregister (&dev->v4l2_dev);v4l2_ctrl_handler_free (&dev->hdl);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 140/371 net: stmmac: sun8i: force select external PHY when no internal one
In reply to Greg Kroah-Hartman[ Upstream commit 0fec7e72ae1391bb2d7527efb54fe6ae88acabce ]
The PHY selection bit also exists on SoCs without an internal PHY; if it's set to 1 (internal PHY, default value) then the MAC will not make use of any PHY on such SoCs.
This problem appears when adapting for H6, which has no real internal PHY (the "internal PHY" on H6 is not on-die, but on a co-packaged AC200 chip, connected via RMII interface at GPIO bank A).
Force the PHY selection bit to 0 when the SOC doesn't have an internal PHY, to address the problem of a wrong default value.
--- drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 5 +++++ 1 file changed, 5 insertions(+)
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +5 -0
@@ -893,6 +893,11 @@ static int sun8i_dwmac_set_syscon(struct stmmac_priv *priv)* address. No need to mask it again. */ reg |=1 <<H3_EPHY_ADDR_SHIFT ; + }else { +/* For SoCs without internal PHY the PHY selection bit should be +* set to 0 (external PHY). +*/ + reg &= ~H3_EPHY_SELECT ; }if (!of_property_read_u32 (node,"allwinner,tx-delay-ps" , &val)) {
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 141/371 rtlwifi: rtl8192cu: fix error handle when usb probe failed
In reply to Greg Kroah-Hartman[ Upstream commit 6c0ed66f1a5b84e2a812c7c2d6571a5621bf3396 ]
rtl_usb_probe() must do error handle rtl_deinit_core() only if rtl_init_core() is done, otherwise goto error_out2.
| usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 | rtl_usb: reg 0xf0, usbctrl_vendorreq TimeOut! status:0xffffffb9 value=0x0 | rtl8192cu: Chip version 0x10 | rtl_usb: reg 0xa, usbctrl_vendorreq TimeOut! status:0xffffffb9 value=0x0 | rtl_usb: Too few input end points found | INFO: trying to register non-static key. | the code is fine but needs lockdep annotation. | turning off the locking correctness validator. | CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.1.0-rc4-319354-g9a33b36 #3 | Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS | Google 01/01/2011 | Workqueue: usb_hub_wq hub_event | Call Trace: | __dump_stack lib/dump_stack.c:77 [inline] | dump_stack+0xe8/0x16e lib/dump_stack.c:113 | assign_lock_key kernel/locking/lockdep.c:786 [inline] | register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095 | __lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582 | lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211 | __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline] | _raw_spin_lock_irqsave+0x44/0x60 kernel/locking/spinlock.c:152 | rtl_c2hcmd_launcher+0xd1/0x390 | drivers/net/wireless/realtek/rtlwifi/base.c:2344 | rtl_deinit_core+0x25/0x2d0 drivers/net/wireless/realtek/rtlwifi/base.c:574 | rtl_usb_probe.cold+0x861/0xa70 | drivers/net/wireless/realtek/rtlwifi/usb.c:1093 | usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361 | really_probe+0x2da/0xb10 drivers/base/dd.c:509 | driver_probe_device+0x21d/0x350 drivers/base/dd.c:671 | __device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778 | bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454 | __device_attach+0x223/0x3a0 drivers/base/dd.c:844 | bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514 | device_add+0xad2/0x16e0 drivers/base/core.c:2106 | usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021 | generic_probe+0xa2/0xda drivers/usb/core/generic.c:210 | usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266 | really_probe+0x2da/0xb10 drivers/base/dd.c:509 | driver_probe_device+0x21d/0x350 drivers/base/dd.c:671 | __device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778 | bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454 | __device_attach+0x223/0x3a0 drivers/base/dd.c:844 | bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514 | device_add+0xad2/0x16e0 drivers/base/core.c:2106 | usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534 | hub_port_connect drivers/usb/core/hub.c:5089 [inline] | hub_port_connect_change drivers/usb/core/hub.c:5204 [inline] | port_event drivers/usb/core/hub.c:5350 [inline] | hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432 | process_one_work+0x90f/0x1580 kernel/workqueue.c:2269 | worker_thread+0x9b/0xe20 kernel/workqueue.c:2415 | kthread+0x313/0x420 kernel/kthread.c:253 | ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
--- drivers/net/wireless/realtek/rtlwifi/usb.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/net/wireless/realtek/rtlwifi/usb.c +3 -2
@@ -1064,13 +1064,13 @@ int rtl_usb_probe(struct usb_interface *intf, rtlpriv->cfg->ops->read_eeprom_info (hw); err =_rtl_usb_init (hw);if (err) - goto error_out; + goto error_out2;rtl_usb_init_sw (hw);/* Init mac80211 sw */ err =rtl_init_core (hw);if (err) {pr_err ("Can't allocate sw for mac80211\n" ); - goto error_out; + goto error_out2; }if (rtlpriv->cfg->ops->init_sw_vars (hw)) {pr_err ("Can't init_sw_vars\n" );
@@ -1091,6 +1091,7 @@ int rtl_usb_probe(struct usb_interface *intf, error_out:rtl_deinit_core (hw); +error_out2:_rtl_usb_io_handler_release (hw);usb_put_dev (udev);complete (&rtlpriv->firmware_loading_complete);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 142/371 mt7601u: do not schedule rx_tasklet when the device has been disconnected
In reply to Greg Kroah-Hartman[ Upstream commit 4079e8ccabc3b6d1b503f2376123cb515d14921f ]
Do not schedule rx_tasklet when the usb dongle is disconnected. Moreover do not grub rx_lock in mt7601u_kill_rx since usb_poison_urb can run concurrently with urb completion and we can unlink urbs from rx ring in any order.
This patch fixes the common kernel warning reported when
the device is removed.
[ 24.921354] usb 3-14: USB disconnect, device number 7 [ 24.921593] ------------[ cut here ]------------ [ 24.921594] RX urb mismatch [ 24.921675] WARNING: CPU: 4 PID: 163 at drivers/net/wireless/mediatek/mt7601u/dma.c:200 mt7601u_complete_rx+0xcb/0xd0 [mt7601u] [ 24.921769] CPU: 4 PID: 163 Comm: kworker/4:2 Tainted: G OE 4.19.31-041931-generic #201903231635 [ 24.921770] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./Z97 Extreme4, BIOS P1.30 05/23/2014 [ 24.921782] Workqueue: usb_hub_wq hub_event [ 24.921797] RIP: 0010:mt7601u_complete_rx+0xcb/0xd0 [mt7601u] [ 24.921800] RSP: 0018:ffff9bd9cfd03d08 EFLAGS: 00010086 [ 24.921802] RAX: 0000000000000000 RBX: ffff9bd9bf043540 RCX: 0000000000000006 [ 24.921803] RDX: 0000000000000007 RSI: 0000000000000096 RDI: ffff9bd9cfd16420 [ 24.921804] RBP: ffff9bd9cfd03d28 R08: 0000000000000002 R09: 00000000000003a8 [ 24.921805] R10: 0000002f485fca34 R11: 0000000000000000 R12: ffff9bd9bf043c1c [ 24.921806] R13: ffff9bd9c62fa3c0 R14: 0000000000000082 R15: 0000000000000000 [ 24.921807] FS: 0000000000000000(0000) GS:ffff9bd9cfd00000(0000) knlGS:0000000000000000 [ 24.921808] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 24.921808] CR2: 00007fb2648b0000 CR3: 0000000142c0a004 CR4: 00000000001606e0 [ 24.921809] Call Trace: [ 24.921812] <IRQ> [ 24.921819] __usb_hcd_giveback_urb+0x8b/0x140 [ 24.921821] usb_hcd_giveback_urb+0xca/0xe0 [ 24.921828] xhci_giveback_urb_in_irq.isra.42+0x82/0xf0 [ 24.921834] handle_cmd_completion+0xe02/0x10d0 [ 24.921837] xhci_irq+0x274/0x4a0 [ 24.921838] xhci_msi_irq+0x11/0x20 [ 24.921851] __handle_irq_event_percpu+0x44/0x190 [ 24.921856] handle_irq_event_percpu+0x32/0x80 [ 24.921861] handle_irq_event+0x3b/0x5a [ 24.921867] handle_edge_irq+0x80/0x190 [ 24.921874] handle_irq+0x20/0x30 [ 24.921889] do_IRQ+0x4e/0xe0 [ 24.921891] common_interrupt+0xf/0xf [ 24.921892] </IRQ> [ 24.921900] RIP: 0010:usb_hcd_flush_endpoint+0x78/0x180 [ 24.921354] usb 3-14: USB disconnect, device number 7
--- drivers/net/wireless/mediatek/mt7601u/dma.c | 33 +++++++++++---------- 1 file changed, 18 insertions(+), 15 deletions(-)
drivers/net/wireless/mediatek/mt7601u/dma.c +18 -15
@@ -193,10 +193,23 @@ static void mt7601u_complete_rx(struct urb *urb)struct mt7601u_rx_queue *q = &dev->rx_q;unsigned long flags; -spin_lock_irqsave (&dev->rx_lock, flags); +/* do no schedule rx tasklet if urb has been unlinked +* or the device has been removed +*/ +switch (urb->status) { +case -ECONNRESET : +case -ESHUTDOWN : +case -ENOENT : +return ; +default : +dev_err_ratelimited (dev->dev,"rx urb failed: %d\n" , + urb->status); +/* fall through */ +case 0 : +break ; + } -if (mt7601u_urb_has_error (urb)) -dev_err (dev->dev,"Error: RX urb failed:%d\n" , urb->status); +spin_lock_irqsave (&dev->rx_lock, flags);if (WARN_ONCE (q->e[q->end].urb != urb,"RX urb mismatch" )) goto out;
@@ -363,19 +376,9 @@ int mt7601u_dma_enqueue_tx(struct mt7601u_dev *dev, struct sk_buff *skb,static void mt7601u_kill_rx (struct mt7601u_dev *dev) {int i; -unsigned long flags; -spin_lock_irqsave (&dev->rx_lock, flags); - -for (i =0 ; i < dev->rx_q.entries; i++) { -int next = dev->rx_q.end; - -spin_unlock_irqrestore (&dev->rx_lock, flags); -usb_poison_urb (dev->rx_q.e[next].urb); -spin_lock_irqsave (&dev->rx_lock, flags); - } - -spin_unlock_irqrestore (&dev->rx_lock, flags); +for (i =0 ; i < dev->rx_q.entries; i++) +usb_poison_urb (dev->rx_q.e[i].urb); } static int mt7601u_submit_rx_buf(struct mt7601u_dev *dev,
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 143/371 x86/build: Add set -e to mkcapflags.sh to delete broken capflags.c
In reply to Greg Kroah-Hartman[ Upstream commit bc53d3d777f81385c1bb08b07bd1c06450ecc2c1 ]
Without 'set -e', shell scripts continue running even after any error occurs. The missed 'set -e' is a typical bug in shell scripting.
For example, when a disk space shortage occurs while this script is running, it actually ends up with generating a truncated capflags.c.
Yet, mkcapflags.sh continues running and exits with 0. So, the build system assumes it has succeeded.
It will not be re-generated in the next invocation of Make since its timestamp is newer than that of any of the source files.
Add 'set -e' so that any error in this script is caught and propagated to the build system.
Since 9c2af1c7377a ("kbuild: add .DELETE_ON_ERROR special target"), make automatically deletes the target on any failure. So, the broken capflags.c will be deleted automatically.
--- arch/x86/kernel/cpu/mkcapflags.sh | 2 ++ 1 file changed, 2 insertions(+)
arch/x86/kernel/cpu/mkcapflags.sh +2 -0
@@ -4,6 +4,8 @@ # Generate the x86_cap/bug_flags[] arrays from include/asm/cpufeatures.h # +set -e + IN=$1 OUT=$2
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 144/371 mt7601u: fix possible memory leak when the device is disconnected
In reply to Greg Kroah-Hartman[ Upstream commit 23377c200b2eb48a60d0f228b2a2e75ed6ee6060 ]
When the device is disconnected while passing traffic it is possible to receive out of order urbs causing a memory leak since the skb linked to the current tx urb is not removed. Fix the issue deallocating the skb cleaning up the tx ring. Moreover this patch fixes the following kernel warning
[ 57.480771] usb 1-1: USB disconnect, device number 2 [ 57.483451] ------------[ cut here ]------------ [ 57.483462] TX urb mismatch [ 57.483481] WARNING: CPU: 1 PID: 32 at drivers/net/wireless/mediatek/mt7601u/dma.c:245 mt7601u_complete_tx+0x165/00 [ 57.483483] Modules linked in: [ 57.483496] CPU: 1 PID: 32 Comm: kworker/1:1 Not tainted 5.2.0-rc1+ #72 [ 57.483498] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.12.0-2.fc30 04/01/2014 [ 57.483502] Workqueue: usb_hub_wq hub_event [ 57.483507] RIP: 0010:mt7601u_complete_tx+0x165/0x1e0 [ 57.483510] Code: 8b b5 10 04 00 00 8b 8d 14 04 00 00 eb 8b 80 3d b1 cb e1 00 00 75 9e 48 c7 c7 a4 ea 05 82 c6 05 f [ 57.483513] RSP: 0000:ffffc900000a0d28 EFLAGS: 00010092 [ 57.483516] RAX: 000000000000000f RBX: ffff88802c0a62c0 RCX: ffffc900000a0c2c [ 57.483518] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff810a8371 [ 57.483520] RBP: ffff88803ced6858 R08: 0000000000000000 R09: 0000000000000001 [ 57.483540] R10: 0000000000000002 R11: 0000000000000000 R12: 0000000000000046 [ 57.483542] R13: ffff88802c0a6c88 R14: ffff88803baab540 R15: ffff88803a0cc078 [ 57.483548] FS: 0000000000000000(0000) GS:ffff88803eb00000(0000) knlGS:0000000000000000 [ 57.483550] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 57.483552] CR2: 000055e7f6780100 CR3: 0000000028c86000 CR4: 00000000000006a0 [ 57.483554] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 57.483556] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 57.483559] Call Trace: [ 57.483561] <IRQ> [ 57.483565] __usb_hcd_giveback_urb+0x77/0xe0 [ 57.483570] xhci_giveback_urb_in_irq.isra.0+0x8b/0x140 [ 57.483574] handle_cmd_completion+0xf5b/0x12c0 [ 57.483577] xhci_irq+0x1f6/0x1810 [ 57.483581] ? lockdep_hardirqs_on+0x9e/0x180 [ 57.483584] ? _raw_spin_unlock_irq+0x24/0x30 [ 57.483588] __handle_irq_event_percpu+0x3a/0x260 [ 57.483592] handle_irq_event_percpu+0x1c/0x60 [ 57.483595] handle_irq_event+0x2f/0x4c [ 57.483599] handle_edge_irq+0x7e/0x1a0 [ 57.483603] handle_irq+0x17/0x20 [ 57.483607] do_IRQ+0x54/0x110 [ 57.483610] common_interrupt+0xf/0xf [ 57.483612] </IRQ>
--- drivers/net/wireless/mediatek/mt7601u/dma.c | 21 ++++++++++++++++----- drivers/net/wireless/mediatek/mt7601u/tx.c | 4 ++-- 2 files changed, 18 insertions(+), 7 deletions(-)
drivers/net/wireless/mediatek/mt7601u/dma.c +16 -5
@@ -241,14 +241,25 @@ static void mt7601u_complete_tx(struct urb *urb)struct sk_buff *skb;unsigned long flags; -spin_lock_irqsave (&dev->tx_lock, flags); +switch (urb->status) { +case -ECONNRESET : +case -ESHUTDOWN : +case -ENOENT : +return ; +default : +dev_err_ratelimited (dev->dev,"tx urb failed: %d\n" , + urb->status); +/* fall through */ +case 0 : +break ; + } -if (mt7601u_urb_has_error (urb)) -dev_err (dev->dev,"Error: TX urb failed:%d\n" , urb->status); +spin_lock_irqsave (&dev->tx_lock, flags);if (WARN_ONCE (q->e[q->start].urb != urb,"TX urb mismatch" )) goto out; skb = q->e[q->start].skb; + q->e[q->start].skb =NULL ;trace_mt_tx_dma_done (dev, skb);__skb_queue_tail (&dev->tx_skb_done, skb);
@@ -448,10 +459,10 @@ static void mt7601u_free_tx_queue(struct mt7601u_tx_queue *q) {int i; -WARN_ON (q->used); -for (i =0 ; i < q->entries; i++) {usb_poison_urb (q->e[i].urb); +if (q->e[i].skb) +mt7601u_tx_status (q->dev, q->e[i].skb);usb_free_urb (q->e[i].urb); } }
drivers/net/wireless/mediatek/mt7601u/tx.c +2 -2
@@ -117,9 +117,9 @@ void mt7601u_tx_status(struct mt7601u_dev *dev, struct sk_buff *skb) info->status.rates[0 ].idx =-1 ; info->flags |=IEEE80211_TX_STAT_ACK ; -spin_lock (&dev->mac_lock); +spin_lock_bh (&dev->mac_lock);ieee80211_tx_status (dev->hw, skb); -spin_unlock (&dev->mac_lock); +spin_unlock_bh (&dev->mac_lock); }static int mt7601u_skb_rooms (struct mt7601u_dev *dev,struct sk_buff *skb)
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 145/371 ipvs: fix tinfo memory leak in start_sync_thread
In reply to Greg Kroah-Hartman[ Upstream commit 5db7c8b9f9fc2aeec671ae3ca6375752c162e0e7 ]
syzkaller reports for memory leak in start_sync_thread [1]
As Eric points out, kthread may start and stop before the threadfn function is called, so there is no chance the data (tinfo in our case) to be released in thread.
Fix this by releasing tinfo in the controlling code instead.
[1]
BUG: memory leak
unreferenced object 0xffff8881206bf700 (size 32):
comm "syz-executor761", pid 7268, jiffies 4294943441 (age 20.470s) hex dump (first 32 bytes):
00 40 7c 09 81 88 ff ff 80 45 b8 21 81 88 ff ff .@|......E.!.... 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<0000000057619e23>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline] [<0000000057619e23>] slab_post_alloc_hook mm/slab.h:439 [inline] [<0000000057619e23>] slab_alloc mm/slab.c:3326 [inline] [<0000000057619e23>] kmem_cache_alloc_trace+0x13d/0x280 mm/slab.c:3553 [<0000000086ce5479>] kmalloc include/linux/slab.h:547 [inline] [<0000000086ce5479>] start_sync_thread+0x5d2/0xe10 net/netfilter/ipvs/ip_vs_sync.c:1862 [<000000001a9229cc>] do_ip_vs_set_ctl+0x4c5/0x780 net/netfilter/ipvs/ip_vs_ctl.c:2402 [<00000000ece457c8>] nf_sockopt net/netfilter/nf_sockopt.c:106 [inline] [<00000000ece457c8>] nf_setsockopt+0x4c/0x80 net/netfilter/nf_sockopt.c:115 [<00000000942f62d4>] ip_setsockopt net/ipv4/ip_sockglue.c:1258 [inline] [<00000000942f62d4>] ip_setsockopt+0x9b/0xb0 net/ipv4/ip_sockglue.c:1238 [<00000000a56a8ffd>] udp_setsockopt+0x4e/0x90 net/ipv4/udp.c:2616 [<00000000fa895401>] sock_common_setsockopt+0x38/0x50 net/core/sock.c:3130 [<0000000095eef4cf>] __sys_setsockopt+0x98/0x120 net/socket.c:2078 [<000000009747cf88>] __do_sys_setsockopt net/socket.c:2089 [inline] [<000000009747cf88>] __se_sys_setsockopt net/socket.c:2086 [inline] [<000000009747cf88>] __x64_sys_setsockopt+0x26/0x30 net/socket.c:2086 [<00000000ded8ba80>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:301 [<00000000893b4ac8>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
--- include/net/ip_vs.h | 6 +- net/netfilter/ipvs/ip_vs_ctl.c | 4 - net/netfilter/ipvs/ip_vs_sync.c | 134 +++++++++++++++++--------------- 3 files changed, 76 insertions(+), 68 deletions(-)
include/net/ip_vs.h +4 -2
@@ -803,11 +803,12 @@ struct ipvs_master_sync_state {struct ip_vs_sync_buff *sync_buff;unsigned long sync_queue_len;unsigned int sync_queue_delay; -struct task_struct *master_thread;struct delayed_work master_wakeup_work;struct netns_ipvs *ipvs; }; +struct ip_vs_sync_thread_data ; +/* How much time to keep dests in trash */ #define IP_VS_DEST_TRASH_PERIOD (120 * HZ)
@@ -938,7 +939,8 @@ struct netns_ipvs {spinlock_t sync_lock;struct ipvs_master_sync_state *ms;spinlock_t sync_buff_lock; -struct task_struct **backup_threads; +struct ip_vs_sync_thread_data *master_tinfo; +struct ip_vs_sync_thread_data *backup_tinfo;int threads_mask;volatile int sync_state;struct mutex sync_mutex;
net/netfilter/ipvs/ip_vs_ctl.c +0 -4
@@ -2382,9 +2382,7 @@ do_ip_vs_set_ctl(struct sock *sk, int cmd, void __user *user, unsigned int len) cfg.syncid = dm->syncid; ret =start_sync_thread (ipvs, &cfg, dm->state); }else { -mutex_lock (&ipvs->sync_mutex); ret =stop_sync_thread (ipvs, dm->state); -mutex_unlock (&ipvs->sync_mutex); } goto out_dec; }
@@ -3490,10 +3488,8 @@ static int ip_vs_genl_del_daemon(struct netns_ipvs *ipvs, struct nlattr **attrs)if (!attrs[IPVS_DAEMON_ATTR_STATE ])return -EINVAL ; -mutex_lock (&ipvs->sync_mutex); ret =stop_sync_thread (ipvs,nla_get_u32 (attrs[IPVS_DAEMON_ATTR_STATE ])); -mutex_unlock (&ipvs->sync_mutex);return ret; }
net/netfilter/ipvs/ip_vs_sync.c +72 -62
269 lines not on this page · raw message
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 146/371 ath10k: add missing error handling
In reply to Greg Kroah-Hartman[ Upstream commit 4b553f3ca4cbde67399aa3a756c37eb92145b8a1 ]
In function ath10k_sdio_mbox_rx_alloc() [sdio.c], ath10k_sdio_mbox_alloc_rx_pkt() is called without handling the error cases. This will make the driver think the allocation for skb is successful and try to access the skb. If we enable failslab, system will easily crash with NULL pointer dereferencing.
Call trace of CONFIG_FAILSLAB:
ath10k_sdio_irq_handler+0x570/0xa88 [ath10k_sdio] process_sdio_pending_irqs+0x4c/0x174 sdio_run_irqs+0x3c/0x64 sdio_irq_work+0x1c/0x28
--- drivers/net/wireless/ath/ath10k/sdio.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/net/wireless/ath/ath10k/sdio.c +4 -0
@@ -602,6 +602,10 @@ static int ath10k_sdio_mbox_rx_alloc(struct ath10k *ar, full_len, last_in_bundle, last_in_bundle); +if (ret) { +ath10k_warn (ar,"alloc_rx_pkt error %d\n" , ret); + goto err; + } } ar_sdio->n_rx_pkts = i;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 147/371 ath10k: fix fw crash by moving chip reset after napi disabled
In reply to Greg Kroah-Hartman[ Upstream commit 08d80e4cd27ba19f9bee9e5f788f9a9fc440a22f ]
On SMP platform, when continuously running wifi up/down, the napi poll can be scheduled during chip reset, which will call ath10k_pci_has_fw_crashed() to check the fw status. But in the reset period, the value from FW_INDICATOR_ADDRESS register will return 0xdeadbeef, which also be treated as fw crash. Fix the issue by moving chip reset after napi disabled.
ath10k_pci 0000:01:00.0: firmware crashed! (guid 73b30611-5b1e-4bdd-90b4-64c81eb947b6) ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1 ath10k_pci 0000:01:00.0: failed to get memcpy hi address for firmware address 4: -16 ath10k_pci 0000:01:00.0: failed to read firmware dump area: -16ath10k_pci 0000:01:00.0: Copy Engine register dump:
ath10k_pci 0000:01:00.0: [00]: 0x0004a000 0 0 0 0 ath10k_pci 0000:01:00.0: [01]: 0x0004a400 0 0 0 0 ath10k_pci 0000:01:00.0: [02]: 0x0004a800 0 0 0 0 ath10k_pci 0000:01:00.0: [03]: 0x0004ac00 0 0 0 0 ath10k_pci 0000:01:00.0: [04]: 0x0004b000 0 0 0 0 ath10k_pci 0000:01:00.0: [05]: 0x0004b400 0 0 0 0 ath10k_pci 0000:01:00.0: [06]: 0x0004b800 0 0 0 0 ath10k_pci 0000:01:00.0: [07]: 0x0004bc00 1 0 1 0 ath10k_pci 0000:01:00.0: [08]: 0x0004c000 0 0 0 0 ath10k_pci 0000:01:00.0: [09]: 0x0004c400 0 0 0 0 ath10k_pci 0000:01:00.0: [10]: 0x0004c800 0 0 0 0 ath10k_pci 0000:01:00.0: [11]: 0x0004cc00 0 0 0 0
Tested HW: QCA9984,QCA9887,WCN3990
--- drivers/net/wireless/ath/ath10k/pci.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-)
drivers/net/wireless/ath/ath10k/pci.c +5 -4
@@ -2059,6 +2059,11 @@ static void ath10k_pci_hif_stop(struct ath10k *ar)ath10k_dbg (ar,ATH10K_DBG_BOOT ,"boot hif stop\n" ); +ath10k_pci_irq_disable (ar); +ath10k_pci_irq_sync (ar); +napi_synchronize (&ar->napi); +napi_disable (&ar->napi); +/* Most likely the device has HTT Rx ring configured. The only way to * prevent the device from accessing (and possible corrupting) host * memory is to reset the chip now.
@@ -2072,10 +2077,6 @@ static void ath10k_pci_hif_stop(struct ath10k *ar)*/ ath10k_pci_safe_chip_reset (ar); -ath10k_pci_irq_disable (ar); -ath10k_pci_irq_sync (ar); -napi_synchronize (&ar->napi); -napi_disable (&ar->napi);ath10k_pci_flush (ar);spin_lock_irqsave (&ar_pci->ps_lock, flags);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 148/371 ath10k: fix PCIE device wake up failed
In reply to Greg Kroah-Hartman[ Upstream commit 011d4111c8c602ea829fa4917af1818eb0500a90 ]
Observed PCIE device wake up failed after ~120 iterations of soft-reboot test. The error message is
"ath10k_pci 0000:01:00.0: failed to wake up device : -110"
The call trace as below:ath10k_pci_probe -> ath10k_pci_force_wake -> ath10k_pci_wake_wait -> ath10k_pci_is_awake
Once trigger the device to wake up, we will continuously check the RTC state until it returns RTC_STATE_V_ON or timeout.
But for QCA99x0 chips, we use wrong value for RTC_STATE_V_ON. Occasionally, we get 0x7 on the fist read, we thought as a failure case, but actually is the right value, also verified with the spec. So fix the issue by changing RTC_STATE_V_ON from 0x5 to 0x7, passed ~2000 iterations.
Tested HW: QCA9984
--- drivers/net/wireless/ath/ath10k/hw.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/wireless/ath/ath10k/hw.c +1 -1
@@ -158,7 +158,7 @@ const struct ath10k_hw_values qca6174_values = { };const struct ath10k_hw_values qca99x0_values = { - .rtc_state_val_on =5 , + .rtc_state_val_on =7 , .ce_count =12 , .msi_assign_ce_max =12 , .num_target_ce_config_wlan =10 ,
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 149/371 perf tools: Increase MAX_NR_CPUS and MAX_CACHES
In reply to Greg Kroah-Hartman[ Upstream commit 9f94c7f947e919c343b30f080285af53d0fa9902 ]
Attempting to profile 1024 or more CPUs with perf causes two errors:
perf record -a
[ perf record: Woken up X times to write data ]
way too many cpu caches..
[ perf record: Captured and wrote X MB perf.data (X samples) ]
perf report -C 1024
Error: failed to set cpu bitmap
Requested CPU 1024 too large. Consider raising MAX_NR_CPUS
Increasing MAX_NR_CPUS from 1024 to 2048 and redefining MAX_CACHES as MAX_NR_CPUS * 4 returns normal functionality to perf:
perf record -a
[ perf record: Woken up X times to write data ]
[ perf record: Captured and wrote X MB perf.data (X samples) ]
perf report -C 1024
...
--- tools/perf/perf.h | 2 +- tools/perf/util/header.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
tools/perf/perf.h +1 -1
@@ -26,7 +26,7 @@ static inline unsigned long long rdclock(void) }#ifndef MAX_NR_CPUS -#define MAX_NR_CPUS 1024 +#define MAX_NR_CPUS 2048#endif extern const char *input_name;
tools/perf/util/header.c +1 -1
@@ -1100,7 +1100,7 @@ static int build_caches(struct cpu_cache_level caches[], u32 size, u32 *cntp)return 0 ; } -#define MAX_CACHES 2000 +#define MAX_CACHES (MAX_NR_CPUS * 4)static int write_cache (struct feat_fd *ff,struct perf_evlist *evlist__maybe_unused )
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 150/371 ASoC: Intel: hdac_hdmi: Set ops to NULL on remove
In reply to Greg Kroah-Hartman[ Upstream commit 0f6ff78540bd1b4df1e0f17806b0ce2e1dff0d78 ]
When we unload Skylake driver we may end up calling hdac_component_master_unbind(), it uses acomp->audio_ops, which we set in hdmi_codec_probe(), so we need to set it to NULL in hdmi_codec_remove(), otherwise we will dereference no longer existing pointer.
--- sound/soc/codecs/hdac_hdmi.c | 6 ++++++ 1 file changed, 6 insertions(+)
sound/soc/codecs/hdac_hdmi.c +6 -0
@@ -1880,6 +1880,12 @@ static void hdmi_codec_remove(struct snd_soc_component *component) {struct hdac_hdmi_priv *hdmi =snd_soc_component_get_drvdata (component);struct hdac_device *hdev = hdmi->hdev; +int ret; + + ret =snd_hdac_acomp_register_notifier (hdev->bus,NULL ); +if (ret <0 ) +dev_err (&hdev->dev,"notifier unregister failed: err: %d\n" , + ret);pm_runtime_disable (&hdev->dev); }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 151/371 clocksource/drivers/tegra: Release all IRQs on request_irq() error
In reply to Greg Kroah-Hartman[ Upstream commit 7a3916706e858ad0bc3b5629c68168e1449de26a ]
Release all requested IRQ's on the request error to properly clean up allocated resources.
--- drivers/clocksource/timer-tegra20.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/clocksource/timer-tegra20.c +3 -2
@@ -310,7 +310,7 @@ static int __init tegra_init_timer(struct device_node *np)pr_err ("%s: can't map IRQ for CPU%d\n" , __func__, cpu); ret = -EINVAL ; - goto out; + goto out_irq; }irq_set_status_flags (cpu_to->clkevt.irq,IRQ_NOAUTOEN );
@@ -320,7 +320,8 @@ static int __init tegra_init_timer(struct device_node *np)if (ret) {pr_err ("%s: cannot setup irq %d for CPU%d\n" , __func__, cpu_to->clkevt.irq, cpu); - ret = -EINVAL ; +irq_dispose_mapping (cpu_to->clkevt.irq); + cpu_to->clkevt.irq =0 ; goto out_irq; } }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 152/371 libata: dont request sense data on !ZAC ATA devices
In reply to Greg Kroah-Hartman[ Upstream commit ca156e006add67e4beea7896be395160735e09b0 ]
ZAC support added sense data requesting on error for both ZAC and ATA devices. This seems to cause erratic error handling behaviors on some SSDs where the device reports sense data availability and then delivers the wrong content making EH take the wrong actions. The failure mode was sporadic on a LITE-ON ssd and couldn't be reliably reproduced.
There is no value in requesting sense data from non-ZAC ATA devices while there's a significant risk of introducing EH misbehaviors which are difficult to reproduce and fix. Let's do the sense data dancing only for ZAC devices.
--- drivers/ata/libata-eh.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-)
drivers/ata/libata-eh.c +5 -3
@@ -1486,7 +1486,7 @@ static int ata_eh_read_log_10h(struct ata_device *dev, tf->hob_lbah = buf[10 ]; tf->nsect = buf[12 ]; tf->hob_nsect = buf[13 ]; -if (ata_id_has_ncq_autosense (dev->id)) +if (dev->class ==ATA_DEV_ZAC &&ata_id_has_ncq_autosense (dev->id)) tf->auxiliary = buf[14 ] <<16 | buf[15 ] <<8 | buf[16 ];return 0 ;
@@ -1733,7 +1733,8 @@ void ata_eh_analyze_ncq_error(struct ata_link *link)memcpy (&qc->result_tf, &tf,sizeof (tf)); qc->result_tf.flags =ATA_TFLAG_ISADDR |ATA_TFLAG_LBA |ATA_TFLAG_LBA48 ; qc->err_mask |=AC_ERR_DEV |AC_ERR_NCQ ; -if ((qc->result_tf.command &ATA_SENSE ) || qc->result_tf.auxiliary) { +if (dev->class ==ATA_DEV_ZAC && + ((qc->result_tf.command &ATA_SENSE ) || qc->result_tf.auxiliary)) {char sense_key, asc, ascq; sense_key = (qc->result_tf.auxiliary >>16 ) &0xff ;
@@ -1787,10 +1788,11 @@ static unsigned int ata_eh_analyze_tf(struct ata_queued_cmd *qc, }switch (qc->dev->class) { -case ATA_DEV_ATA :case ATA_DEV_ZAC :if (stat &ATA_SENSE )ata_eh_request_sense (qc, qc->scsicmd); +/* fall through */ +case ATA_DEV_ATA :if (err &ATA_ICRC ) qc->err_mask |=AC_ERR_ATA_BUS ;if (err & (ATA_UNC |ATA_AMNF ))
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 153/371 clocksource/drivers/tegra: Restore base address before cleanup
In reply to Greg Kroah-Hartman[ Upstream commit fc9babc2574691d3bbf0428f007b22261fed55c6 ]
We're adjusting the timer's base for each per-CPU timer to point to the actual start of the timer since device-tree defines a compound registers range that includes all of the timers. In this case the original base need to be restore before calling iounmap to unmap the proper address.
--- drivers/clocksource/timer-tegra20.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/clocksource/timer-tegra20.c +2 -0
@@ -341,6 +341,8 @@ static int __init tegra_init_timer(struct device_node *np)irq_dispose_mapping (cpu_to->clkevt.irq); } } + + to->of_base.base = timer_reg_base; out:timer_of_cleanup (to);return ret;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 154/371 clocksource/drivers/exynos_mct: Increase priority over ARM arch timer
In reply to Greg Kroah-Hartman[ Upstream commit 6282edb72bed5324352522d732080d4c1b9dfed6 ]
Exynos SoCs based on CA7/CA15 have 2 timer interfaces: custom Exynos MCT (Multi Core Timer) and standard ARM Architected Timers.
There are use cases, where both timer interfaces are used simultanously. One of such examples is using Exynos MCT for the main system timer and ARM Architected Timers for the KVM and virtualized guests (KVM requires arch timers).
Exynos Multi-Core Timer driver (exynos_mct) must be however started before ARM Architected Timers (arch_timer), because they both share some common hardware blocks (global system counter) and turning on MCT is needed to get ARM Architected Timer working properly.
To ensure selecting Exynos MCT as the main system timer, increase MCT timer rating. To ensure proper starting order of both timers during suspend/resume cycle, increase MCT hotplug priority over ARM Archictected Timers.
--- drivers/clocksource/exynos_mct.c | 4 ++-- include/linux/cpuhotplug.h | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-)
drivers/clocksource/exynos_mct.c +2 -2
@@ -209,7 +209,7 @@ static void exynos4_frc_resume(struct clocksource *cs)static struct clocksource mct_frc = { .name ="mct-frc" , - .rating =400 , + .rating =450 ,/* use value higher than ARM arch timer */ .read = exynos4_frc_read, .mask =CLOCKSOURCE_MASK (32 ), .flags =CLOCK_SOURCE_IS_CONTINUOUS ,
@@ -464,7 +464,7 @@ static int exynos4_mct_starting_cpu(unsigned int cpu) evt->set_state_oneshot_stopped = set_state_shutdown; evt->tick_resume = set_state_shutdown; evt->features =CLOCK_EVT_FEAT_PERIODIC |CLOCK_EVT_FEAT_ONESHOT ; - evt->rating =450 ; + evt->rating =500 ;/* use value higher than ARM arch timer */ exynos4_mct_write (TICK_BASE_CNT , mevt->base +MCT_L_TCNTB_OFFSET );
include/linux/cpuhotplug.h +1 -1
@@ -116,10 +116,10 @@ enum cpuhp_state {CPUHP_AP_PERF_ARM_ACPI_STARTING ,CPUHP_AP_PERF_ARM_STARTING ,CPUHP_AP_ARM_L2X0_STARTING , +CPUHP_AP_EXYNOS4_MCT_TIMER_STARTING ,CPUHP_AP_ARM_ARCH_TIMER_STARTING ,CPUHP_AP_ARM_GLOBAL_TIMER_STARTING ,CPUHP_AP_JCORE_TIMER_STARTING , -CPUHP_AP_EXYNOS4_MCT_TIMER_STARTING ,CPUHP_AP_ARM_TWD_STARTING ,CPUHP_AP_QCOM_TIMER_STARTING , CPUHP_AP_TEGRA_TIMER_STARTING,
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 155/371 netfilter: ctnetlink: Fix regression in conntrack entry deletion
In reply to Greg Kroah-Hartman[ Upstream commit e7600865db32b69deb0109b8254244dca592adcf ]
Commit f8e608982022 ("netfilter: ctnetlink: Resolve conntrack L3-protocol flush regression") introduced a regression in which deletion of conntrack entries would fail because the L3 protocol information is replaced by AF_UNSPEC. As a result the search for the entry to be deleted would turn up empty due to the tuple used to perform the search is now different from the tuple used to initially set up the entry.
For flushing the conntrack table we do however want to keep the option for nfgenmsg->version to have a non-zero value to allow for newer user-space tools to request treatment under the new behavior. With that it is possible to independently flush tables for a defined L3 protocol. This was introduced with the enhancements in in commit 59c08c69c278 ("netfilter: ctnetlink: Support L3 protocol-filter on flush").
Older user-space tools will retain the behavior of flushing all tables regardless of defined L3 protocol.
--- net/netfilter/nf_conntrack_netlink.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
net/netfilter/nf_conntrack_netlink.c +4 -3
@@ -1254,7 +1254,6 @@ static int ctnetlink_del_conntrack(struct net *net, struct sock *ctnl,struct nf_conntrack_tuple tuple;struct nf_conn *ct;struct nfgenmsg *nfmsg =nlmsg_data (nlh); -u_int8_t u3 = nfmsg->version ? nfmsg->nfgen_family :AF_UNSPEC ;struct nf_conntrack_zone zone;int err;
@@ -1264,11 +1263,13 @@ static int ctnetlink_del_conntrack(struct net *net, struct sock *ctnl,if (cda[CTA_TUPLE_ORIG ]) err =ctnetlink_parse_tuple (cda, &tuple,CTA_TUPLE_ORIG , - u3, &zone); + nfmsg->nfgen_family, &zone);else if (cda[CTA_TUPLE_REPLY ]) err =ctnetlink_parse_tuple (cda, &tuple,CTA_TUPLE_REPLY , - u3, &zone); + nfmsg->nfgen_family, &zone);else { +u_int8_t u3 = nfmsg->version ? nfmsg->nfgen_family :AF_UNSPEC ; +return ctnetlink_flush_conntrack (net, cda,NETLINK_CB (skb).portid,nlmsg_report (nlh), u3);
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 156/371 xsk: Properly terminate assignment in xskq_produce_flush_desc
In reply to Greg Kroah-Hartman[ Upstream commit f7019b7b0ad14bde732b8953161994edfc384953 ]
Clang warns:
In file included from net/xdp/xsk_queue.c:10:net/xdp/xsk_queue.h:292:2: warning: expression result unused [-Wunused-value]
WRITE_ONCE(q->ring->producer, q->prod_tail);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/compiler.h:284:6: note: expanded from macro 'WRITE_ONCE'
__u.__val; \
~~~ ^~~~~1 warning generated.
The q->prod_tail assignment has a comma at the end, not a semi-colon. Fix that so clang no longer warns and everything works as expected.
--- net/xdp/xsk_queue.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
net/xdp/xsk_queue.h +1 -1
@@ -240,7 +240,7 @@ static inline void xskq_produce_flush_desc(struct xsk_queue *q)/* Order producer and data */ smp_wmb (); - q->prod_tail = q->prod_head, + q->prod_tail = q->prod_head;WRITE_ONCE (q->ring->producer, q->prod_tail); }
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 157/371 rslib: Fix decoding of shortened codes
In reply to Greg Kroah-Hartman[ Upstream commit 2034a42d1747fc1e1eeef2c6f1789c4d0762cb9c ]
The decoding of shortenend codes is broken. It only works as expected if there are no erasures.
When decoding with erasures, Lambda (the error and erasure locator polynomial) is initialized from the given erasure positions. The pad parameter is not accounted for by the initialisation code, and hence Lambda is initialized from incorrect erasure positions.
The fix is to adjust the erasure positions by the supplied pad.
--- lib/reed_solomon/decode_rs.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
lib/reed_solomon/decode_rs.c +2 -2
@@ -99,9 +99,9 @@if (no_eras >0 ) {/* Init lambda to be the erasure locator polynomial */ lambda[1 ] = alpha_to[rs_modnn (rs, - prim * (nn -1 - eras_pos[0 ]))]; + prim * (nn -1 - (eras_pos[0 ] + pad)))];for (i =1 ; i < no_eras; i++) { - u =rs_modnn (rs, prim * (nn -1 - eras_pos[i])); + u =rs_modnn (rs, prim * (nn -1 - (eras_pos[i] + pad)));for (j = i +1 ; j >0 ; j--) { tmp = index_of[lambda[j -1 ]];if (tmp != nn) {
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 158/371 bpf: fix BPF_ALU32 | BPF_ARSH on BE arches
In reply to Greg Kroah-Hartman[ Upstream commit 75672dda27bd00109a84cd975c17949ad9c45663 ]
Yauheni reported the following code do not work correctly on BE arches:
ALU_ARSH_X:
DST = (u64) (u32) ((*(s32 *) &DST) >> SRC);
CONT;
ALU_ARSH_K:
DST = (u64) (u32) ((*(s32 *) &DST) >> IMM);
CONT;and are causing failure of test_verifier test 'arsh32 on imm 2' on BE arches.
The code is taking address and interpreting memory directly, so is not endianness neutral. We should instead perform standard C type casting on the variable. A u64 to s32 conversion will drop the high 32-bit and reserve the low 32-bit as signed integer, this is all we want.
--- kernel/bpf/core.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
kernel/bpf/core.c +2 -2
@@ -1367,10 +1367,10 @@ static u64 ___bpf_prog_run(u64 *regs, const struct bpf_insn *insn, u64 *stack) insn++;CONT ; ALU_ARSH_X: -DST = (u64) (u32) ((*(s32 *) &DST ) >>SRC ); +DST = (u64) (u32) (((s32 )DST ) >>SRC );CONT ; ALU_ARSH_K: -DST = (u64) (u32) ((*(s32 *) &DST ) >>IMM ); +DST = (u64) (u32) (((s32 )DST ) >>IMM );CONT ; ALU64_ARSH_X: (*(s64 *) &DST ) >>=SRC ;
Signature · 1 line
2.20.1
Greg Kroah-Hartman
maintainerPATCH 159/371 rslib: Fix handling of of caller provided syndrome
In reply to Greg Kroah-Hartman[ Upstream commit ef4d6a8556b637ad27c8c2a2cff1dda3da38e9a9 ]
Check if the syndrome provided by the caller is zero, and act accordingly.
--- lib/reed_solomon/decode_rs.c | 14 ++++++++++++-- 1 file changed, 12 insertions(+), 2 deletions(-)
lib/reed_solomon/decode_rs.c +12 -2
@@ -42,8 +42,18 @@BUG_ON (pad <0 || pad >= nn);/* Does the caller provide the syndrome ? */ -if (s !=NULL ) - goto decode; +if (s !=NULL ) { +for (i =0 ; i < nroots; i++) { +/* The syndrome is in index form, +* so nn represents zero +*/ +if (s[i] != nn) + goto decode; + } + +/* syndrome is zero, no errors to correct */ +return 0 ; + }/* form the syndromes; i.e., evaluate data(x) at roots of * g(x) */
Signature · 1 line
2.20.1