Skip to contentSkip to conversation

net: stmmac: Make MDIO bus reset optional

PATCH Applied Thierry Reding 2 participants 4 messages Jul 26, 2019 – Jul 27, 2019

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 net: stmmac: Make MDIO bus reset optional

From: Thierry Reding <[email protected]>

The Tegra EQOS driver already resets the MDIO bus at probe time via the reset GPIO specified in the phy-reset-gpios device tree property. There is no need to reset the bus again later on.

This avoids the need to query the device tree for the snps,reset GPIO, which is not part of the Tegra EQOS device tree bindings. This quiesces an error message from the generic bus reset code if it doesn't find the snps,reset related delays.

---
 drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c | 3 +++
 drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c       | 4 +++-
 drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c        | 1 +
 drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c   | 8 +++++++-
 include/linux/stmmac.h                                  | 1 +
 5 files changed, 15 insertions(+), 2 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c +3 -0
index 3a14cdd01f5f..66933332c68e 100644
@@ -333,6 +333,9 @@ static void *tegra_eqos_probe(struct platform_device *pdev,
 	usleep_range(2000, 4000);
 	gpiod_set_value(eqos->reset, 0);
 
+	/* MDIO bus was already reset just above */
+	data->mdio_bus_data->needs_reset = false;
+
 	eqos->rst = devm_reset_control_get(&pdev->dev, "eqos");
 	if (IS_ERR(eqos->rst)) {
 		err = PTR_ERR(eqos->rst);
drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c +3 -1
index 4304c1abc5d1..40c42637ad75 100644
@@ -348,7 +348,9 @@ int stmmac_mdio_register(struct net_device *ndev)
 		max_addr = PHY_MAX_ADDR;
 	}
 
-	new_bus->reset = &stmmac_mdio_reset;
+	if (mdio_bus_data->needs_reset)
+		new_bus->reset = &stmmac_mdio_reset;
+
 	snprintf(new_bus->id, MII_BUS_ID_SIZE, "%s-%x",
 		 new_bus->name, priv->plat->bus_id);
 	new_bus->priv = ndev;
drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c +1 -0
index 86f9c07a38cf..d5d08e11c353 100644
@@ -63,6 +63,7 @@ static void common_default_data(struct plat_stmmacenet_data *plat)
 	plat->has_gmac = 1;
 	plat->force_sf_dma_mode = 1;
 
+	plat->mdio_bus_data->needs_reset = true;
 	plat->mdio_bus_data->phy_mask = 0;
 
 	/* Set default value for multicast hash bins */
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c +7 -1
index 73fc2524372e..333b09564b88 100644
@@ -342,10 +342,16 @@ static int stmmac_dt_phy(struct plat_stmmacenet_data *plat,
 		mdio = true;
 	}
 
-	if (mdio)
+	if (mdio) {
 		plat->mdio_bus_data =
 			devm_kzalloc(dev, sizeof(struct stmmac_mdio_bus_data),
 				     GFP_KERNEL);
+		if (!plat->mdio_bus_data)
+			return -ENOMEM;
+
+		plat->mdio_bus_data->needs_reset = true;
+	}
+
 	return 0;
 }
 
include/linux/stmmac.h +1 -0
index 7d06241582dd..7b3e354bcd3c 100644
@@ -81,6 +81,7 @@ struct stmmac_mdio_bus_data {
 	unsigned int phy_mask;
 	int *irqs;
 	int probed_phy_irq;
+	bool needs_reset;
 };
 
 struct stmmac_dma_cfg {
Signature · 1 line
2.22.0
#1 lore raw

PATCH 2/2 net: stmmac: Do not request stmmaceth clock

From: Thierry Reding <[email protected]>

The stmmaceth clock is specified by the slave_bus and apb_pclk clocks in the device tree bindings for snps,dwc-qos-ethernet-4.10 compatible nodes of this IP.

The subdrivers for these bindings will be requesting the stmmac clock correctly at a later point, so there is no need to request it here and cause an error message to be printed to the kernel log.

---
 .../net/ethernet/stmicro/stmmac/stmmac_platform.c  | 14 ++++++++------
 1 file changed, 8 insertions(+), 6 deletions(-)
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c +8 -6
index 333b09564b88..7ad2bb90ceb1 100644
@@ -521,13 +521,15 @@ stmmac_probe_config_dt(struct platform_device *pdev, const char **mac)
 	}
 
 	/* clock setup */
-	plat->stmmac_clk = devm_clk_get(&pdev->dev,
-					STMMAC_RESOURCE_NAME);
-	if (IS_ERR(plat->stmmac_clk)) {
-		dev_warn(&pdev->dev, "Cannot get CSR clock\n");
-		plat->stmmac_clk = NULL;
+	if (!of_device_is_compatible(np, "snps,dwc-qos-ethernet-4.10")) {
+		plat->stmmac_clk = devm_clk_get(&pdev->dev,
+						STMMAC_RESOURCE_NAME);
+		if (IS_ERR(plat->stmmac_clk)) {
+			dev_warn(&pdev->dev, "Cannot get CSR clock\n");
+			plat->stmmac_clk = NULL;
+		}
+		clk_prepare_enable(plat->stmmac_clk);
 	}
-	clk_prepare_enable(plat->stmmac_clk);
 
 	plat->pclk = devm_clk_get(&pdev->dev, "pclk");
 	if (IS_ERR(plat->pclk)) {
Signature · 1 line
2.22.0
maintainer Applied
#2 lore raw

Re: [PATCH net-next 2/2] net: stmmac: Do not request stmmaceth clock

From: Thierry Reding <[email protected]>
Date: Fri, 26 Jul 2019 12:27:41 +0200

Quoted 11 lines

From: Thierry Reding <[email protected]>

The stmmaceth clock is specified by the slave_bus and apb_pclk clocks in the device tree bindings for snps,dwc-qos-ethernet-4.10 compatible nodes of this IP.

The subdrivers for these bindings will be requesting the stmmac clock correctly at a later point, so there is no need to request it here and cause an error message to be printed to the kernel log.

Applied.

maintainer Applied
#3 lore raw
In reply to Thierry Reding

From: Thierry Reding <[email protected]>
Date: Fri, 26 Jul 2019 12:27:40 +0200

Quoted 6 lines

From: Thierry Reding <[email protected]>

The Tegra EQOS driver already resets the MDIO bus at probe time via the reset GPIO specified in the phy-reset-gpios device tree property. There is no need to reset the bus again later on.

Quoted 6 lines

This avoids the need to query the device tree for the snps,reset GPIO, which is not part of the Tegra EQOS device tree bindings. This quiesces an error message from the generic bus reset code if it doesn't find the snps,reset related delays.

Applied.