Skip to contentSkip to conversation

dt-bindings: pinctrl: qcom: Add SC7180 pinctrl binding

PATCH In review Rajendra Nayak 2 participants 4 messages Aug 6, 2019 – Aug 7, 2019

Subsystems (6)
lore
Share & tools
lore
#0 lore raw

PATCH v3 1/2 dt-bindings: pinctrl: qcom: Add SC7180 pinctrl binding

From: Jitendra Sharma <[email protected]>

Add the binding for the TLMM pinctrl block found in the SC7180 platform

[rnayak: Fix some copy-paste issues, sort and fix functions]

---
v3: Minor typo fixes as pointed out by Vinod on v2.
Added Vinods Reviewed-by:

 .../bindings/pinctrl/qcom,sc7180-pinctrl.txt  | 186 ++++++++++++++++++
 1 file changed, 186 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,sc7180-pinctrl.txt
Documentation/devicetree/bindings/pinctrl/qcom,sc7180-pinctrl.txt new file +186 -0
new file mode 100644
index 000000000000..b5767ee82ee6
@@ -0,0 +1,186 @@
+Qualcomm Technologies, Inc. SC7180 TLMM block
+
+This binding describes the Top Level Mode Multiplexer block found in the
+SC7180 platform.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be "qcom,sc7180-pinctrl"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: the base address and size of the north, south and west
+		    TLMM tiles
+
+- reg-names:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: names for the cells of reg, must contain "north", "south"
+		    and "west".
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: should specify the TLMM summary IRQ.
+
+- interrupt-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as an interrupt controller
+
+- #interrupt-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/interrupt-controller/irq.h>
+
+- gpio-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as a gpio controller
+
+- #gpio-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/gpio/gpio.h>
+
+- gpio-ranges:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition:  see ../gpio/gpio.txt
+
+- gpio-reserved-ranges:
+	Usage: optional
+	Value type: <prop-encoded-array>
+	Definition: see ../gpio/gpio.txt
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+	Usage: required
+	Value type: <string-array>
+	Definition: List of gpio pins affected by the properties specified in
+		    this subnode.
+
+		    Valid pins are:
+		      gpio0-gpio118
+		        Supports mux, bias and drive-strength
+
+		      sdc1_clk, sdc1_cmd, sdc1_data sdc2_clk, sdc2_cmd,
+		      sdc2_data sdc1_rclk
+		        Supports bias and drive-strength
+
+		      ufs_reset
+			Supports bias and drive-strength
+
+- function:
+	Usage: required
+	Value type: <string>
+	Definition: Specify the alternative function to be configured for the
+		    specified pins. Functions are only valid for gpio pins.
+		    Valid values are:
+
+		    adsp_ext, agera_pll, aoss_cti, atest_char, atest_char0,
+		    atest_char1, atest_char2, atest_char3, atest_tsens,
+		    atest_tsens2, atest_usb1, atest_usb10, atest_usb11,
+		    atest_usb12, atest_usb13, atest_usb2, atest_usb20,
+		    atest_usb21, atest_usb22, atest_usb23, audio_ref,
+		    btfm_slimbus, cam_mclk, cci_async, cci_i2c, cci_timer0,
+		    cci_timer1, cci_timer2, cci_timer3, cci_timer4,
+		    cri_trng, dbg_out, ddr_bist, ddr_pxi0, ddr_pxi1,
+		    ddr_pxi2, ddr_pxi3, dp_hot, edp_lcd, gcc_gp1, gcc_gp2,
+		    gcc_gp3, gpio, gp_pdm0, gp_pdm1, gp_pdm2, gps_tx,
+		    jitter_bist, ldo_en, ldo_update, lpass_ext, mdp_vsync,
+		    mdp_vsync0, mdp_vsync1, mdp_vsync2, mdp_vsync3, mi2s_0,
+		    mi2s_1, mi2s_2, mss_lte, m_voc, pa_indicator, phase_flag,
+		    PLL_BIST, pll_bypassnl, pll_reset, prng_rosc, qdss,
+		    qdss_cti, qlink_enable, qlink_request, qspi_clk, qspi_cs,
+		    qspi_data, qup00, qup01, qup02, qup03, qup04, qup05,
+		    qup10, qup11, qup12, qup13, qup14, qup15, sdc1_tb,
+		    sdc2_tb, sd_write, sp_cmu, tgu_ch0, tgu_ch1, tgu_ch2,
+		    tgu_ch3, tsense_pwm1, tsense_pwm2, uim1, uim2, uim_batt,
+		    usb_phy, vfr_1, _V_GPIO, _V_PPS_IN, _V_PPS_OUT,
+		    vsense_trigger, wlan1_adc0, wlan1_adc1, wlan2_adc0,
+		    wlan2_adc1,
+
+- bias-disable:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configured as no pull.
+
+- bias-pull-down:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configured as pull down.
+
+- bias-pull-up:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configured as pull up.
+
+- output-high:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    high.
+		    Not valid for sdc pins.
+
+- output-low:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    low.
+		    Not valid for sdc pins.
+
+- drive-strength:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the drive strength for the specified pins, in mA.
+		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
+
+Example:
+
+	tlmm: pinctrl@3500000 {
+		compatible = "qcom,sc7180-pinctrl";
+		reg = <0x3500000 0x300000>,
+		      <0x3900000 0x300000>,
+		      <0x3D00000 0x300000>;
+		reg-names = "west", "north", "south";
+		interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-ranges = <&tlmm 0 0 119>;
+		gpio-reserved-ranges = <0 4>, <106 4>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#1 lore raw

PATCH v3 2/2 pinctrl: qcom: Add SC7180 pinctrl driver

From: Jitendra Sharma <[email protected]>

Add initial pinctrl driver to support pin configuration with pinctrl framework for SC7180

[rnayak: modify to use upstream tile support
sort and squash some functions]

---
v3: No change since v2 except for adding Vinods Reviewed-by:

 drivers/pinctrl/qcom/Kconfig          |    9 +
 drivers/pinctrl/qcom/Makefile         |    1 +
 drivers/pinctrl/qcom/pinctrl-sc7180.c | 1146 +++++++++++++++++++++++++
 3 files changed, 1156 insertions(+)
 create mode 100644 drivers/pinctrl/qcom/pinctrl-sc7180.c
drivers/pinctrl/qcom/Kconfig +9 -0
index 8e14a5f2e970..af44dafc35e7 100644
@@ -158,6 +158,15 @@ config PINCTRL_QCOM_SSBI_PMIC
          which are using SSBI for communication with SoC. Example PMIC's
          devices are pm8058 and pm8921.
 
+config PINCTRL_SC7180
+	tristate "Qualcomm Technologies Inc SC7180 pin controller driver"
+	depends on GPIOLIB && OF
+	select PINCTRL_MSM
+	help
+	  This is the pinctrl, pinmux, pinconf and gpiolib driver for the
+	  Qualcomm Technologies Inc TLMM block found on the Qualcomm
+	  Technologies Inc SC7180 platform.
+
 config PINCTRL_SDM660
        tristate "Qualcomm Technologies Inc SDM660 pin controller driver"
        depends on GPIOLIB && OF
drivers/pinctrl/qcom/Makefile +1 -0
index ebe906872272..f8bb0c265381 100644
@@ -20,6 +20,7 @@ obj-$(CONFIG_PINCTRL_QCOM_SPMI_PMIC) += pinctrl-spmi-gpio.o
 obj-$(CONFIG_PINCTRL_QCOM_SPMI_PMIC) += pinctrl-spmi-mpp.o
 obj-$(CONFIG_PINCTRL_QCOM_SSBI_PMIC) += pinctrl-ssbi-gpio.o
 obj-$(CONFIG_PINCTRL_QCOM_SSBI_PMIC) += pinctrl-ssbi-mpp.o
+obj-$(CONFIG_PINCTRL_SC7180)	+= pinctrl-sc7180.o
 obj-$(CONFIG_PINCTRL_SDM660)   += pinctrl-sdm660.o
 obj-$(CONFIG_PINCTRL_SDM845) += pinctrl-sdm845.o
 obj-$(CONFIG_PINCTRL_SM8150) += pinctrl-sm8150.o
drivers/pinctrl/qcom/pinctrl-sc7180.c new file +1146 -0

1,146 lines not on this page · raw message

Signature · 2 lines
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
#2 lore raw

Re: [PATCH v3 2/2] pinctrl: qcom: Add SC7180 pinctrl driver

Quoted 5 lines · Rajendra Nayak

From: Jitendra Sharma <[email protected]>

Add initial pinctrl driver to support pin configuration with pinctrl framework for SC7180

Quoted 7 lines

[rnayak: modify to use upstream tile support
sort and squash some functions]

Patch applied!

Yours,
Linus Walleij

#3 lore raw
In reply to Rajendra Nayak
Quoted 10 lines · Rajendra Nayak

From: Jitendra Sharma <[email protected]>

Add the binding for the TLMM pinctrl block found in the SC7180 platform

[rnayak: Fix some copy-paste issues, sort and fix functions]

Patch applied.

Yours,
Linus Walleij