Makefile: Add target to generate hex output for combined spl and dtb
PATCH RESEND v3 1/2 Makefile: Add target to generate hex output for combined spl and dtb
From: Dalon Westergreen <[email protected]>
Stratix10 requires a hex image of the spl plus spl devicetree offset to the Stratix10 onchip memory located at SPL_TEXT_BASE. This patch adds a target to generate a hex file from the u-boot-spl binary including the dtb offset at SPL_TEST_BASE.
Objcopy is used to convert the $(SPL_BIN).bin, which includes the spl dtb, to a hex file. the --change-address option is used to offset the hex to SPL_TEXT_BASE as objcopy on the spl binary will not result in a hex file appropriately offset at SPL_TEXT_BASE.
---
Changes in v3:
-> Cleanup commit message and better describe the problem being
resolved
-> Remove extraneous hunk
-> use SPL_BIN instead of u-boot-spl
Changes in v2:
-> Move spl hex file generation to SPL Makefile
-> Create hexfile from $(SPL_BIN).bin which will include the dtb
ifneq(build_dtb,)
--- Makefile | 8 +++----- scripts/Makefile.spl | 7 +++++++ 2 files changed, 10 insertions(+), 5 deletions(-)
Makefile +3 -5
@@ -1129,11 +1129,6 @@ OBJCOPYFLAGS_u-boot-nodtb.bin := -O binary \ $(if $(CONFIG_X86_16BIT_INIT),-R .start16 -R .resetvec) \ $(if $(CONFIG_MPC85XX_HAVE_RESET_VECTOR),-R .bootpg -R .resetvec) -OBJCOPYFLAGS_u-boot-spl.hex = $(OBJCOPYFLAGS_u-boot.hex) - -spl/u-boot-spl.hex: spl/u-boot-spl FORCE - $(call if_changed,objcopy) - binary_size_check: u-boot-nodtb.bin FORCE @file_size=$(shell wc -c u-boot-nodtb.bin | awk '{print $$1}') ; \ map_size=$(shell cat u-boot.map | \
@@ -1715,6 +1710,9 @@ spl/u-boot-spl.bin: spl/u-boot-spl @: $(SPL_SIZE_CHECK) +spl/u-boot-spl.hex: spl/u-boot-spl + @: + spl/u-boot-spl: tools prepare \ $(if $(CONFIG_OF_SEPARATE)$(CONFIG_OF_EMBED)$(CONFIG_SPL_OF_PLATDATA),dts/dt.dtb) \ $(if $(CONFIG_OF_SEPARATE)$(CONFIG_OF_EMBED)$(CONFIG_TPL_OF_PLATDATA),dts/dt.dtb)
scripts/Makefile.spl +7 -0
@@ -216,6 +216,8 @@ ifneq ($(CONFIG_TARGET_SOCFPGA_GEN5)$(CONFIG_TARGET_SOCFPGA_ARRIA10),) ALL-y += $(obj)/$(SPL_BIN).sfp endif +ALL-$(CONFIG_TARGET_SOCFPGA_STRATIX10) += $(obj)/$(SPL_BIN).hex + ifdef CONFIG_ARCH_SUNXI ALL-y += $(obj)/sunxi-spl.bin
@@ -363,6 +365,11 @@ endif $(obj)/$(SPL_BIN).sfp: $(obj)/$(SPL_BIN).bin FORCE $(call if_changed,mkimage) +OBJCOPYFLAGS_$(SPL_BIN).hex := -I binary -O ihex --change-address=$(CONFIG_SPL_TEXT_BASE) + +$(obj)/$(SPL_BIN).hex: $(obj)/$(SPL_BIN).bin FORCE + $(call if_changed,objcopy) + quiet_cmd_mksunxiboot = MKSUNXI $@ cmd_mksunxiboot = $(objtree)/tools/mksunxiboot \ --default-dt $(CONFIG_DEFAULT_DEVICE_TREE) $< $@
Signature · 1 line
2.21.0
PATCH RESEND v3 2/2 ARM: socfpga: stratix10: Remove CONFIG_OF_EMBED
From: Dalon Westergreen <[email protected]>
CONFIG_OF_EMBED was primarily enabled to support the stratix10 spl hex file requirements. Since this option now produces a warning during build, and the spl hex can be created using alternate methods, CONFIG_OF_EMBED is no longer needed.
---
Changes in v3:
-> Revert to u-boot.img for SPL payload name
Changes in v2:
-> Change CONFIG_SPL_TARGET back to u-boot-spl.hex
--- configs/socfpga_stratix10_defconfig | 1 - 1 file changed, 1 deletion(-)
configs/socfpga_stratix10_defconfig +0 -1
@@ -26,7 +26,6 @@ CONFIG_CMD_CACHE=y CONFIG_CMD_EXT4=y CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y -CONFIG_OF_EMBED=y CONFIG_DEFAULT_DEVICE_TREE="socfpga_stratix10_socdk" CONFIG_ENV_IS_IN_MMC=y CONFIG_NET_RANDOM_ETHADDR=y
Signature · 1 line
2.21.0