arm: dts: sync dts for Allwinner H6
Subsystems (2)
PATCH 1/1 arm: dts: sync dts for Allwinner H6
Sync Kernel DTS for Allwinner H6 boards.
commit <d45331b00ddb> Linux 5.3-rc4
Signed-off-by Clément Péron <[email protected]>
--- arch/arm/dts/sun50i-h6-beelink-gs1.dts | 76 ++++++++++++++++++++++++++ arch/arm/dts/sun50i-h6-pine-h64.dts | 12 ++++ arch/arm/dts/sun50i-h6.dtsi | 43 ++++++++++++++- 3 files changed, 128 insertions(+), 3 deletions(-)
arch/arm/dts/sun50i-h6-beelink-gs1.dts +76 -0
@@ -14,6 +14,7 @@ compatible = "azw,beelink-gs1", "allwinner,sun50i-h6"; aliases { + ethernet0 = &emac; serial0 = &uart0; };
@@ -21,6 +22,17 @@ stdout-path = "serial0:115200n8"; }; + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + leds { compatible = "gpio-leds";
@@ -41,6 +53,40 @@ }; }; +&de { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&ext_rgmii_pins>; + phy-mode = "rgmii"; + phy-handle = <&ext_rgmii_phy>; + phy-supply = <®_aldo2>; + status = "okay"; +}; + +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + +&mdio { + ext_rgmii_phy: ethernet-phy at 1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &mmc0 { vmmc-supply = <®_cldo1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
@@ -57,6 +103,15 @@ status = "okay"; }; +&ohci0 { + status = "okay"; +}; + +&pio { + vcc-pd-supply = <®_cldo1>; + vcc-pg-supply = <®_aldo1>; +}; + &r_i2c { status = "okay";
@@ -177,8 +232,29 @@ }; }; +&r_pio { + /* + * PL0 and PL1 are used for PMIC I2C + * don't enable the pl-supply else + * it will fail at boot + * + * vcc-pl-supply = <®_aldo1>; + */ + vcc-pm-supply = <®_aldo1>; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_ph_pins>; status = "okay"; }; + +&usb2otg { + dr_mode = "host"; + status = "okay"; +}; + +&usb2phy { + usb0_vbus-supply = <®_vcc5v>; + status = "okay"; +};
arch/arm/dts/sun50i-h6-pine-h64.dts +12 -0
@@ -127,6 +127,12 @@ status = "okay"; }; +&pio { + vcc-pc-supply = <®_bldo2>; + vcc-pd-supply = <®_cldo1>; + vcc-pg-supply = <®_aldo1>; +}; + &r_i2c { status = "okay";
@@ -243,10 +249,16 @@ pcf8563: rtc at 51 { compatible = "nxp,pcf8563"; reg = <0x51>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; #clock-cells = <0>; }; }; +&r_pio { + vcc-pm-supply = <®_aldo1>; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_ph_pins>;
arch/arm/dts/sun50i-h6.dtsi +40 -3
90 lines not on this page · raw message
Signature · 1 line
2.20.1
PATCH 1/1 arm: dts: sync dts for Allwinner H6
Hi
Quoted 210 lines · Clément Péron
Sync Kernel DTS for Allwinner H6 boards.
commit <
d45331b00ddb> Linux 5.3-rc4Signed-off-by Clément Péron <[email protected]>--- arch/arm/dts/sun50i-h6-beelink-gs1.dts | 76 ++++++++++++++++++++++++++ arch/arm/dts/sun50i-h6-pine-h64.dts | 12 ++++ arch/arm/dts/sun50i-h6.dtsi | 43 ++++++++++++++- 3 files changed, 128 insertions(+), 3 deletions(-)arch/arm/dts/sun50i-h6-beelink-gs1.dts +76
-0@@ -14,6 +14,7 @@ compatible = "azw,beelink-gs1", "allwinner,sun50i-h6"; aliases { + ethernet0 = &emac; serial0 = &uart0; };@@ -21,6 +22,17 @@ stdout-path = "serial0:115200n8"; }; + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + leds { compatible = "gpio-leds";@@ -41,6 +53,40 @@ }; }; +&de { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&ext_rgmii_pins>; + phy-mode = "rgmii"; + phy-handle = <&ext_rgmii_phy>; + phy-supply = <®_aldo2>; + status = "okay"; +}; + +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + +&mdio { + ext_rgmii_phy: ethernet-phy at 1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &mmc0 { vmmc-supply = <®_cldo1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;@@ -57,6 +103,15 @@ status = "okay"; }; +&ohci0 { + status = "okay"; +}; + +&pio { + vcc-pd-supply = <®_cldo1>; + vcc-pg-supply = <®_aldo1>; +}; + &r_i2c { status = "okay";@@ -177,8 +232,29 @@ }; }; +&r_pio { + /* + * PL0 and PL1 are used for PMIC I2C + * don't enable the pl-supply else + * it will fail at boot + * + * vcc-pl-supply = <®_aldo1>; + */ + vcc-pm-supply = <®_aldo1>; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_ph_pins>; status = "okay"; }; + +&usb2otg { + dr_mode = "host"; + status = "okay"; +}; + +&usb2phy { + usb0_vbus-supply = <®_vcc5v>; + status = "okay"; +};arch/arm/dts/sun50i-h6-pine-h64.dts +12
-0@@ -127,6 +127,12 @@ status = "okay"; }; +&pio { + vcc-pc-supply = <®_bldo2>; + vcc-pd-supply = <®_cldo1>; + vcc-pg-supply = <®_aldo1>; +}; + &r_i2c { status = "okay";@@ -243,10 +249,16 @@ pcf8563: rtc at 51 { compatible = "nxp,pcf8563"; reg = <0x51>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; #clock-cells = <0>; }; }; +&r_pio { + vcc-pm-supply = <®_aldo1>; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_ph_pins>;arch/arm/dts/sun50i-h6.dtsi +22
-1@@ -101,7 +101,7 @@ #size-cells = <1>; ranges; - display-engine at 1000000 { + bus at 1000000 { compatible = "allwinner,sun50i-h6-de3", "allwinner,sun50i-a64-de2"; reg = <0x1000000 0x400000>;@@ -203,11 +203,32 @@ #reset-cells = <1>; }; + dma: dma-controller at 3002000 { + compatible = "allwinner,sun50i-h6-dma"; + reg = <0x03002000 0x1000>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>; + clock-names = "bus", "mbus"; + dma-channels = <16>; + dma-requests = <46>; + resets = <&ccu RST_BUS_DMA>; + #dma-cells = <1>; + }; + sid: sid at 3006000 { compatible = "allwinner,sun50i-h6-sid"; reg = <0x03006000 0x400>; }; + watchdog: watchdog at 30090a0 { + compatible = "allwinner,sun50i-h6-wdt", + "allwinner,sun6i-a31-wdt"; + reg = <0x030090a0 0x20>; + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; + /* Broken on some H6 boards */ + status = "disabled"; + }; + pio: pinctrl at 300b000 { compatible = "allwinner,sun50i-h6-pinctrl"; reg = <0x0300b000 0x400>;
arch/arm/dts/sun50i-h6.dtsi line 267
Quoted 4 lines
arch/arm/dts/sun50i-h6.dtsi +1
-0@@ -243,6 +264,15 @@ bias-pull-up; }; + /omit-if-no-ref/
Avoid this patch the /omit-if-no-ref/ can't be interpreted on U-boot.
Regards,
Clément
Quoted 53 lines
arch/arm/dts/sun50i-h6.dtsi +17
-3+ mmc1_pins: mmc1-pins { + pins = "PG0", "PG1", "PG2", "PG3", + "PG4", "PG5"; + function = "mmc1"; + drive-strength = <30>; + bias-pull-up; + }; + mmc2_pins: mmc2-pins { pins = "PC1", "PC4", "PC5", "PC6", "PC7", "PC8", "PC9", "PC10",@@ -294,6 +324,8 @@ resets = <&ccu RST_BUS_MMC1>; reset-names = "ahb"; interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; status = "disabled"; #address-cells = <1>; #size-cells = <0>;@@ -445,7 +477,6 @@ resets = <&ccu RST_BUS_OHCI3>, <&ccu RST_BUS_EHCI3>; phys = <&usb2phy 3>; - phy-names = "usb"; status = "disabled"; };@@ -457,7 +488,6 @@ <&ccu CLK_USB_OHCI3>; resets = <&ccu RST_BUS_OHCI3>; phys = <&usb2phy 3>; - phy-names = "usb"; status = "disabled"; };@@ -613,6 +643,13 @@ #reset-cells = <1>; }; + r_watchdog: watchdog at 7020400 { + compatible = "allwinner,sun50i-h6-wdt", + "allwinner,sun6i-a31-wdt"; + reg = <0x07020400 0x20>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + }; + r_intc: interrupt-controller at 7021000 { compatible = "allwinner,sun50i-h6-r-intc", "allwinner,sun6i-a31-r-intc"; --2.20.1