Skip to contentSkip to conversation

Enable USB host controller on Odroid-C2

U-Boot New Beniamino Galvani 2 participants 11 messages Aug 18, 2019 – May 11, 2020

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

Hi,

these two patches enable the USB host controller on Odroid-C2. The first patch adds a PHY driver; the second one enables the necessary configuration options and updates the device tree.

Note that the DWC2 driver currently does not support enabling PHYs from the device tree and so the following series (still on review) is needed as runtime requirement for the second patch:

[PATCH 0/5] usb: host: dwc2: use driver model for PHY and CLOCK

Thanks,
Beniamino

Beniamino Galvani (2):
phy: meson: add GXBB PHY driver
odroid-c2: enable USB host controller

 arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi |   8 +
 configs/odroid-c2_defconfig                  |   7 +
 drivers/phy/Kconfig                          |   8 +
 drivers/phy/Makefile                         |   1 +
 drivers/phy/meson-gxbb-usb2.c                | 235 +++++++++++++++++++
 include/configs/meson64.h                    |   5 +
 6 files changed, 264 insertions(+)
 create mode 100644 drivers/phy/meson-gxbb-usb2.c
Signature · 1 line
2.21.0
#1 lore raw

PATCH 1/2 phy: meson: add GXBB PHY driver

This adds support for the USB PHY found on Amlogic GXBB SoCs.

---
 drivers/phy/Kconfig           |   8 ++
 drivers/phy/Makefile          |   1 +
 drivers/phy/meson-gxbb-usb2.c | 235 ++++++++++++++++++++++++++++++++++
 3 files changed, 244 insertions(+)
 create mode 100644 drivers/phy/meson-gxbb-usb2.c
drivers/phy/Kconfig +8 -0
index 3942f035eb..2190f6f970 100644
@@ -154,6 +154,14 @@ config PHY_STM32_USBPHYC
 	  between an HS USB OTG controller and an HS USB Host controller,
 	  selected by an USB switch.
 
+config MESON_GXBB_USB_PHY
+	bool "Amlogic Meson GXBB USB PHY"
+	depends on PHY && ARCH_MESON && MESON_GXBB
+	imply REGMAP
+	help
+	  This is the generic phy driver for the Amlogic Meson GXBB
+	  USB2 PHY.
+
 config MESON_GXL_USB_PHY
 	bool "Amlogic Meson GXL USB PHYs"
 	depends on PHY && ARCH_MESON && (MESON_GXL || MESON_GXM)
drivers/phy/Makefile +1 -0
index 3157f1b7ee..dde3b0ecef 100644
@@ -16,6 +16,7 @@ obj-$(CONFIG_STI_USB_PHY) += sti_usb_phy.o
 obj-$(CONFIG_PHY_RCAR_GEN2) += phy-rcar-gen2.o
 obj-$(CONFIG_PHY_RCAR_GEN3) += phy-rcar-gen3.o
 obj-$(CONFIG_PHY_STM32_USBPHYC) += phy-stm32-usbphyc.o
+obj-$(CONFIG_MESON_GXBB_USB_PHY) += meson-gxbb-usb2.o
 obj-$(CONFIG_MESON_GXL_USB_PHY) += meson-gxl-usb2.o meson-gxl-usb3.o
 obj-$(CONFIG_MESON_G12A_USB_PHY) += meson-g12a-usb2.o meson-g12a-usb3-pcie.o
 obj-$(CONFIG_MSM8916_USB_PHY) += msm8916-usbh-phy.o
drivers/phy/meson-gxbb-usb2.c new file +235 -0

235 lines not on this page · raw message

Signature · 1 line
2.21.0
#2 lore raw

PATCH 1/2 phy: meson: add GXBB PHY driver

Quoted 273 lines · Beniamino Galvani

This adds support for the USB PHY found on Amlogic GXBB SoCs.

---
 drivers/phy/Kconfig           |   8 ++
 drivers/phy/Makefile          |   1 +
 drivers/phy/meson-gxbb-usb2.c | 235 ++++++++++++++++++++++++++++++++++
 3 files changed, 244 insertions(+)
 create mode 100644 drivers/phy/meson-gxbb-usb2.c
drivers/phy/Kconfig +8 -0
index 3942f035eb..2190f6f970 100644
@@ -154,6 +154,14 @@ config PHY_STM32_USBPHYC
 	  between an HS USB OTG controller and an HS USB Host controller,
 	  selected by an USB switch.
 
+config MESON_GXBB_USB_PHY
+	bool "Amlogic Meson GXBB USB PHY"
+	depends on PHY && ARCH_MESON && MESON_GXBB
+	imply REGMAP
+	help
+	  This is the generic phy driver for the Amlogic Meson GXBB
+	  USB2 PHY.
+
 config MESON_GXL_USB_PHY
 	bool "Amlogic Meson GXL USB PHYs"
 	depends on PHY && ARCH_MESON && (MESON_GXL || MESON_GXM)
drivers/phy/Makefile +1 -0
index 3157f1b7ee..dde3b0ecef 100644
@@ -16,6 +16,7 @@ obj-$(CONFIG_STI_USB_PHY) += sti_usb_phy.o
 obj-$(CONFIG_PHY_RCAR_GEN2) += phy-rcar-gen2.o
 obj-$(CONFIG_PHY_RCAR_GEN3) += phy-rcar-gen3.o
 obj-$(CONFIG_PHY_STM32_USBPHYC) += phy-stm32-usbphyc.o
+obj-$(CONFIG_MESON_GXBB_USB_PHY) += meson-gxbb-usb2.o
 obj-$(CONFIG_MESON_GXL_USB_PHY) += meson-gxl-usb2.o meson-gxl-usb3.o
 obj-$(CONFIG_MESON_G12A_USB_PHY) += meson-g12a-usb2.o meson-g12a-usb3-pcie.o
 obj-$(CONFIG_MSM8916_USB_PHY) += msm8916-usbh-phy.o
drivers/phy/meson-gxbb-usb2.c new file +225 -0
new file mode 100644
index 0000000000..88c2ec69b2
@@ -0,0 +1,235 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Meson8, Meson8b and GXBB USB2 PHY driver
+ *
+ * Copyright (C) 2016 Martin Blumenstingl <[email protected]>
+ * Copyright (C) 2018 BayLibre, SAS
+ *
+ * Author: Beniamino Galvani <[email protected]>
+ */
+
+#include <common.h>
+#include <clk.h>
+#include <dm.h>
+#include <generic-phy.h>
+#include <power/regulator.h>
+#include <regmap.h>
+#include <reset.h>
+
+#define REG_CONFIG					0x00
+	#define REG_CONFIG_CLK_EN			BIT(0)
+	#define REG_CONFIG_CLK_SEL_MASK			GENMASK(3, 1)
+	#define REG_CONFIG_CLK_DIV_MASK			GENMASK(10, 4)
+	#define REG_CONFIG_CLK_32k_ALTSEL		BIT(15)
+	#define REG_CONFIG_TEST_TRIG			BIT(31)
+
+#define REG_CTRL					0x04
+	#define REG_CTRL_SOFT_PRST			BIT(0)
+	#define REG_CTRL_SOFT_HRESET			BIT(1)
+	#define REG_CTRL_SS_SCALEDOWN_MODE_MASK		GENMASK(3, 2)
+	#define REG_CTRL_CLK_DET_RST			BIT(4)
+	#define REG_CTRL_INTR_SEL			BIT(5)
+	#define REG_CTRL_CLK_DETECTED			BIT(8)
+	#define REG_CTRL_SOF_SENT_RCVD_TGL		BIT(9)
+	#define REG_CTRL_SOF_TOGGLE_OUT			BIT(10)
+	#define REG_CTRL_POWER_ON_RESET			BIT(15)
+	#define REG_CTRL_SLEEPM				BIT(16)
+	#define REG_CTRL_TX_BITSTUFF_ENN_H		BIT(17)
+	#define REG_CTRL_TX_BITSTUFF_ENN		BIT(18)
+	#define REG_CTRL_COMMON_ON			BIT(19)
+	#define REG_CTRL_REF_CLK_SEL_MASK		GENMASK(21, 20)
+	#define REG_CTRL_REF_CLK_SEL_SHIFT		20
+	#define REG_CTRL_FSEL_MASK			GENMASK(24, 22)
+	#define REG_CTRL_FSEL_SHIFT			22
+	#define REG_CTRL_PORT_RESET			BIT(25)
+	#define REG_CTRL_THREAD_ID_MASK			GENMASK(31, 26)
+
+/* bits [31:26], [24:21] and [15:3] seem to be read-only */
+#define REG_ADP_BC					0x0c
+	#define REG_ADP_BC_VBUS_VLD_EXT_SEL		BIT(0)
+	#define REG_ADP_BC_VBUS_VLD_EXT			BIT(1)
+	#define REG_ADP_BC_OTG_DISABLE			BIT(2)
+	#define REG_ADP_BC_ID_PULLUP			BIT(3)
+	#define REG_ADP_BC_DRV_VBUS			BIT(4)
+	#define REG_ADP_BC_ADP_PRB_EN			BIT(5)
+	#define REG_ADP_BC_ADP_DISCHARGE		BIT(6)
+	#define REG_ADP_BC_ADP_CHARGE			BIT(7)
+	#define REG_ADP_BC_SESS_END			BIT(8)
+	#define REG_ADP_BC_DEVICE_SESS_VLD		BIT(9)
+	#define REG_ADP_BC_B_VALID			BIT(10)
+	#define REG_ADP_BC_A_VALID			BIT(11)
+	#define REG_ADP_BC_ID_DIG			BIT(12)
+	#define REG_ADP_BC_VBUS_VALID			BIT(13)
+	#define REG_ADP_BC_ADP_PROBE			BIT(14)
+	#define REG_ADP_BC_ADP_SENSE			BIT(15)
+	#define REG_ADP_BC_ACA_ENABLE			BIT(16)
+	#define REG_ADP_BC_DCD_ENABLE			BIT(17)
+	#define REG_ADP_BC_VDAT_DET_EN_B		BIT(18)
+	#define REG_ADP_BC_VDAT_SRC_EN_B		BIT(19)
+	#define REG_ADP_BC_CHARGE_SEL			BIT(20)
+	#define REG_ADP_BC_CHARGE_DETECT		BIT(21)
+	#define REG_ADP_BC_ACA_PIN_RANGE_C		BIT(22)
+	#define REG_ADP_BC_ACA_PIN_RANGE_B		BIT(23)
+	#define REG_ADP_BC_ACA_PIN_RANGE_A		BIT(24)
+	#define REG_ADP_BC_ACA_PIN_GND			BIT(25)
+	#define REG_ADP_BC_ACA_PIN_FLOAT		BIT(26)
+
+#define RESET_COMPLETE_TIME				500
+#define ACA_ENABLE_COMPLETE_TIME			50
+
+struct phy_meson_gxbb_usb2_priv {
+	struct regmap *regmap;
+	struct reset_ctl_bulk resets;
+#if CONFIG_IS_ENABLED(DM_REGULATOR)
+	struct udevice *phy_supply;
+#endif
+};
+
+static int phy_meson_gxbb_usb2_power_on(struct phy *phy)
+{
+	struct udevice *dev = phy->dev;
+	struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev);
+	uint val;
+
+#if CONFIG_IS_ENABLED(DM_REGULATOR)
+	if (priv->phy_supply) {
+		int ret = regulator_set_enable(priv->phy_supply, true);
+
+		if (ret)
+			return ret;
+	}
+#endif
+
+	regmap_update_bits(priv->regmap, REG_CONFIG,
+			   REG_CONFIG_CLK_32k_ALTSEL,
+			   REG_CONFIG_CLK_32k_ALTSEL);
+	regmap_update_bits(priv->regmap, REG_CTRL,
+			   REG_CTRL_REF_CLK_SEL_MASK,
+			   0x2 << REG_CTRL_REF_CLK_SEL_SHIFT);
+	regmap_update_bits(priv->regmap, REG_CTRL,
+			   REG_CTRL_FSEL_MASK,
+			   0x5 << REG_CTRL_FSEL_SHIFT);
+
+	/* reset the PHY */
+	regmap_update_bits(priv->regmap, REG_CTRL,
+			   REG_CTRL_POWER_ON_RESET,
+			   REG_CTRL_POWER_ON_RESET);
+	udelay(RESET_COMPLETE_TIME);
+	regmap_update_bits(priv->regmap, REG_CTRL,
+			   REG_CTRL_POWER_ON_RESET,
+			   0);
+	udelay(RESET_COMPLETE_TIME);
+
+	regmap_update_bits(priv->regmap, REG_CTRL,
+			   REG_CTRL_SOF_TOGGLE_OUT,
+			   REG_CTRL_SOF_TOGGLE_OUT);
+
+	/* Set host mode */
+	regmap_update_bits(priv->regmap, REG_ADP_BC,
+			   REG_ADP_BC_ACA_ENABLE,
+			   REG_ADP_BC_ACA_ENABLE);
+	udelay(ACA_ENABLE_COMPLETE_TIME);
+
+	regmap_read(priv->regmap, REG_ADP_BC, &val);
+	if (val & REG_ADP_BC_ACA_PIN_FLOAT) {
+		pr_err("Error powering on GXBB USB PHY\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int phy_meson_gxbb_usb2_power_off(struct phy *phy)
+{
+#if CONFIG_IS_ENABLED(DM_REGULATOR)
+	struct udevice *dev = phy->dev;
+	struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev);
+
+	if (priv->phy_supply) {
+		int ret = regulator_set_enable(priv->phy_supply, false);
+
+		if (ret)
+			return ret;
+	}
+#endif
+
+	return 0;
+}
+
+static struct phy_ops meson_gxbb_usb2_phy_ops = {
+	.power_on = phy_meson_gxbb_usb2_power_on,
+	.power_off = phy_meson_gxbb_usb2_power_off,
+};
+
+static int meson_gxbb_usb2_phy_probe(struct udevice *dev)
+{
+	struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev);
+	struct clk clk_usb_general, clk_usb;
+	int ret;
+
+	ret = regmap_init_mem(dev_ofnode(dev), &priv->regmap);
+	if (ret)
+		return ret;
+
+	ret = clk_get_by_name(dev, "usb_general", &clk_usb_general);
+	if (ret)
+		return ret;
+
+	ret = clk_enable(&clk_usb_general);
+	if (ret && ret != -ENOSYS && ret != -ENOTSUPP) {
+		pr_err("Failed to enable PHY general clock\n");
+		return ret;
+	}
+
+	ret = clk_get_by_name(dev, "usb", &clk_usb);
+	if (ret)
+		return ret;
+
+	ret = clk_enable(&clk_usb);
+	if (ret && ret != -ENOSYS && ret != -ENOTSUPP) {
+		pr_err("Failed to enable PHY clock\n");
+		return ret;
+	}
+
+#if CONFIG_IS_ENABLED(DM_REGULATOR)
+	ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply);
+	if (ret && ret != -ENOENT) {
+		pr_err("Failed to get PHY regulator\n");
+		return ret;
+	}
+#endif
+	ret = reset_get_bulk(dev, &priv->resets);
+	if (!ret) {
+		ret = reset_deassert_bulk(&priv->resets);
+		if (ret) {
+			pr_err("Failed to deassert reset\n");
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int meson_gxbb_usb2_phy_remove(struct udevice *dev)
+{
+	struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev);
+
+	return reset_release_bulk(&priv->resets);
+}
+
+static const struct udevice_id meson_gxbb_usb2_phy_ids[] = {
+	{ .compatible = "amlogic,meson8-usb2-phy" },
+	{ .compatible = "amlogic,meson8b-usb2-phy" },
+	{ .compatible = "amlogic,meson-gxbb-usb2-phy" },
+	{ }
+};

drivers/phy/meson-gxbb-usb2.c line 235

Quoted 10 lines
drivers/phy/meson-gxbb-usb2.c new file +10 -0
+
+U_BOOT_DRIVER(meson_gxbb_usb2_phy) = {
+	.name = "meson_gxbb_usb2_phy",
+	.id = UCLASS_PHY,
+	.of_match = meson_gxbb_usb2_phy_ids,
+	.probe = meson_gxbb_usb2_phy_probe,
+	.remove = meson_gxbb_usb2_phy_remove,
+	.ops = &meson_gxbb_usb2_phy_ops,
+	.priv_auto_alloc_size = sizeof(struct phy_meson_gxbb_usb2_priv),
+};
#3 lore raw

PATCH 1/2 phy: meson: add GXBB PHY driver

In reply to Beniamino Galvani
Quoted 273 lines · Beniamino Galvani

This adds support for the USB PHY found on Amlogic GXBB SoCs.

---
 drivers/phy/Kconfig           |   8 ++
 drivers/phy/Makefile          |   1 +
 drivers/phy/meson-gxbb-usb2.c | 235 ++++++++++++++++++++++++++++++++++
 3 files changed, 244 insertions(+)
 create mode 100644 drivers/phy/meson-gxbb-usb2.c
drivers/phy/Kconfig +8 -0
index 3942f035eb..2190f6f970 100644
@@ -154,6 +154,14 @@ config PHY_STM32_USBPHYC
 	  between an HS USB OTG controller and an HS USB Host controller,
 	  selected by an USB switch.
 
+config MESON_GXBB_USB_PHY
+	bool "Amlogic Meson GXBB USB PHY"
+	depends on PHY && ARCH_MESON && MESON_GXBB
+	imply REGMAP
+	help
+	  This is the generic phy driver for the Amlogic Meson GXBB
+	  USB2 PHY.
+
 config MESON_GXL_USB_PHY
 	bool "Amlogic Meson GXL USB PHYs"
 	depends on PHY && ARCH_MESON && (MESON_GXL || MESON_GXM)
drivers/phy/Makefile +1 -0
index 3157f1b7ee..dde3b0ecef 100644
@@ -16,6 +16,7 @@ obj-$(CONFIG_STI_USB_PHY) += sti_usb_phy.o
 obj-$(CONFIG_PHY_RCAR_GEN2) += phy-rcar-gen2.o
 obj-$(CONFIG_PHY_RCAR_GEN3) += phy-rcar-gen3.o
 obj-$(CONFIG_PHY_STM32_USBPHYC) += phy-stm32-usbphyc.o
+obj-$(CONFIG_MESON_GXBB_USB_PHY) += meson-gxbb-usb2.o
 obj-$(CONFIG_MESON_GXL_USB_PHY) += meson-gxl-usb2.o meson-gxl-usb3.o
 obj-$(CONFIG_MESON_G12A_USB_PHY) += meson-g12a-usb2.o meson-g12a-usb3-pcie.o
 obj-$(CONFIG_MSM8916_USB_PHY) += msm8916-usbh-phy.o
drivers/phy/meson-gxbb-usb2.c new file +225 -0
new file mode 100644
index 0000000000..88c2ec69b2
@@ -0,0 +1,235 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Meson8, Meson8b and GXBB USB2 PHY driver
+ *
+ * Copyright (C) 2016 Martin Blumenstingl <[email protected]>
+ * Copyright (C) 2018 BayLibre, SAS
+ *
+ * Author: Beniamino Galvani <[email protected]>
+ */
+
+#include <common.h>
+#include <clk.h>
+#include <dm.h>
+#include <generic-phy.h>
+#include <power/regulator.h>
+#include <regmap.h>
+#include <reset.h>
+
+#define REG_CONFIG					0x00
+	#define REG_CONFIG_CLK_EN			BIT(0)
+	#define REG_CONFIG_CLK_SEL_MASK			GENMASK(3, 1)
+	#define REG_CONFIG_CLK_DIV_MASK			GENMASK(10, 4)
+	#define REG_CONFIG_CLK_32k_ALTSEL		BIT(15)
+	#define REG_CONFIG_TEST_TRIG			BIT(31)
+
+#define REG_CTRL					0x04
+	#define REG_CTRL_SOFT_PRST			BIT(0)
+	#define REG_CTRL_SOFT_HRESET			BIT(1)
+	#define REG_CTRL_SS_SCALEDOWN_MODE_MASK		GENMASK(3, 2)
+	#define REG_CTRL_CLK_DET_RST			BIT(4)
+	#define REG_CTRL_INTR_SEL			BIT(5)
+	#define REG_CTRL_CLK_DETECTED			BIT(8)
+	#define REG_CTRL_SOF_SENT_RCVD_TGL		BIT(9)
+	#define REG_CTRL_SOF_TOGGLE_OUT			BIT(10)
+	#define REG_CTRL_POWER_ON_RESET			BIT(15)
+	#define REG_CTRL_SLEEPM				BIT(16)
+	#define REG_CTRL_TX_BITSTUFF_ENN_H		BIT(17)
+	#define REG_CTRL_TX_BITSTUFF_ENN		BIT(18)
+	#define REG_CTRL_COMMON_ON			BIT(19)
+	#define REG_CTRL_REF_CLK_SEL_MASK		GENMASK(21, 20)
+	#define REG_CTRL_REF_CLK_SEL_SHIFT		20
+	#define REG_CTRL_FSEL_MASK			GENMASK(24, 22)
+	#define REG_CTRL_FSEL_SHIFT			22
+	#define REG_CTRL_PORT_RESET			BIT(25)
+	#define REG_CTRL_THREAD_ID_MASK			GENMASK(31, 26)
+
+/* bits [31:26], [24:21] and [15:3] seem to be read-only */
+#define REG_ADP_BC					0x0c
+	#define REG_ADP_BC_VBUS_VLD_EXT_SEL		BIT(0)
+	#define REG_ADP_BC_VBUS_VLD_EXT			BIT(1)
+	#define REG_ADP_BC_OTG_DISABLE			BIT(2)
+	#define REG_ADP_BC_ID_PULLUP			BIT(3)
+	#define REG_ADP_BC_DRV_VBUS			BIT(4)
+	#define REG_ADP_BC_ADP_PRB_EN			BIT(5)
+	#define REG_ADP_BC_ADP_DISCHARGE		BIT(6)
+	#define REG_ADP_BC_ADP_CHARGE			BIT(7)
+	#define REG_ADP_BC_SESS_END			BIT(8)
+	#define REG_ADP_BC_DEVICE_SESS_VLD		BIT(9)
+	#define REG_ADP_BC_B_VALID			BIT(10)
+	#define REG_ADP_BC_A_VALID			BIT(11)
+	#define REG_ADP_BC_ID_DIG			BIT(12)
+	#define REG_ADP_BC_VBUS_VALID			BIT(13)
+	#define REG_ADP_BC_ADP_PROBE			BIT(14)
+	#define REG_ADP_BC_ADP_SENSE			BIT(15)
+	#define REG_ADP_BC_ACA_ENABLE			BIT(16)
+	#define REG_ADP_BC_DCD_ENABLE			BIT(17)
+	#define REG_ADP_BC_VDAT_DET_EN_B		BIT(18)
+	#define REG_ADP_BC_VDAT_SRC_EN_B		BIT(19)
+	#define REG_ADP_BC_CHARGE_SEL			BIT(20)
+	#define REG_ADP_BC_CHARGE_DETECT		BIT(21)
+	#define REG_ADP_BC_ACA_PIN_RANGE_C		BIT(22)
+	#define REG_ADP_BC_ACA_PIN_RANGE_B		BIT(23)
+	#define REG_ADP_BC_ACA_PIN_RANGE_A		BIT(24)
+	#define REG_ADP_BC_ACA_PIN_GND			BIT(25)
+	#define REG_ADP_BC_ACA_PIN_FLOAT		BIT(26)
+
+#define RESET_COMPLETE_TIME				500
+#define ACA_ENABLE_COMPLETE_TIME			50
+
+struct phy_meson_gxbb_usb2_priv {
+	struct regmap *regmap;
+	struct reset_ctl_bulk resets;
+#if CONFIG_IS_ENABLED(DM_REGULATOR)
+	struct udevice *phy_supply;
+#endif
+};
+
+static int phy_meson_gxbb_usb2_power_on(struct phy *phy)
+{
+	struct udevice *dev = phy->dev;
+	struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev);
+	uint val;
+
+#if CONFIG_IS_ENABLED(DM_REGULATOR)
+	if (priv->phy_supply) {
+		int ret = regulator_set_enable(priv->phy_supply, true);
+
+		if (ret)
+			return ret;
+	}
+#endif
+
+	regmap_update_bits(priv->regmap, REG_CONFIG,
+			   REG_CONFIG_CLK_32k_ALTSEL,
+			   REG_CONFIG_CLK_32k_ALTSEL);
+	regmap_update_bits(priv->regmap, REG_CTRL,
+			   REG_CTRL_REF_CLK_SEL_MASK,
+			   0x2 << REG_CTRL_REF_CLK_SEL_SHIFT);
+	regmap_update_bits(priv->regmap, REG_CTRL,
+			   REG_CTRL_FSEL_MASK,
+			   0x5 << REG_CTRL_FSEL_SHIFT);
+
+	/* reset the PHY */
+	regmap_update_bits(priv->regmap, REG_CTRL,
+			   REG_CTRL_POWER_ON_RESET,
+			   REG_CTRL_POWER_ON_RESET);
+	udelay(RESET_COMPLETE_TIME);
+	regmap_update_bits(priv->regmap, REG_CTRL,
+			   REG_CTRL_POWER_ON_RESET,
+			   0);
+	udelay(RESET_COMPLETE_TIME);
+
+	regmap_update_bits(priv->regmap, REG_CTRL,
+			   REG_CTRL_SOF_TOGGLE_OUT,
+			   REG_CTRL_SOF_TOGGLE_OUT);
+
+	/* Set host mode */
+	regmap_update_bits(priv->regmap, REG_ADP_BC,
+			   REG_ADP_BC_ACA_ENABLE,
+			   REG_ADP_BC_ACA_ENABLE);
+	udelay(ACA_ENABLE_COMPLETE_TIME);
+
+	regmap_read(priv->regmap, REG_ADP_BC, &val);
+	if (val & REG_ADP_BC_ACA_PIN_FLOAT) {
+		pr_err("Error powering on GXBB USB PHY\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int phy_meson_gxbb_usb2_power_off(struct phy *phy)
+{
+#if CONFIG_IS_ENABLED(DM_REGULATOR)
+	struct udevice *dev = phy->dev;
+	struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev);
+
+	if (priv->phy_supply) {
+		int ret = regulator_set_enable(priv->phy_supply, false);
+
+		if (ret)
+			return ret;
+	}
+#endif
+
+	return 0;
+}
+
+static struct phy_ops meson_gxbb_usb2_phy_ops = {
+	.power_on = phy_meson_gxbb_usb2_power_on,
+	.power_off = phy_meson_gxbb_usb2_power_off,
+};
+
+static int meson_gxbb_usb2_phy_probe(struct udevice *dev)
+{
+	struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev);
+	struct clk clk_usb_general, clk_usb;
+	int ret;
+
+	ret = regmap_init_mem(dev_ofnode(dev), &priv->regmap);
+	if (ret)
+		return ret;
+
+	ret = clk_get_by_name(dev, "usb_general", &clk_usb_general);
+	if (ret)
+		return ret;
+
+	ret = clk_enable(&clk_usb_general);
+	if (ret && ret != -ENOSYS && ret != -ENOTSUPP) {
+		pr_err("Failed to enable PHY general clock\n");
+		return ret;
+	}
+
+	ret = clk_get_by_name(dev, "usb", &clk_usb);
+	if (ret)
+		return ret;
+
+	ret = clk_enable(&clk_usb);
+	if (ret && ret != -ENOSYS && ret != -ENOTSUPP) {
+		pr_err("Failed to enable PHY clock\n");
+		return ret;
+	}
+
+#if CONFIG_IS_ENABLED(DM_REGULATOR)
+	ret = device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply);
+	if (ret && ret != -ENOENT) {
+		pr_err("Failed to get PHY regulator\n");
+		return ret;
+	}
+#endif
+	ret = reset_get_bulk(dev, &priv->resets);
+	if (!ret) {
+		ret = reset_deassert_bulk(&priv->resets);
+		if (ret) {
+			pr_err("Failed to deassert reset\n");
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int meson_gxbb_usb2_phy_remove(struct udevice *dev)
+{
+	struct phy_meson_gxbb_usb2_priv *priv = dev_get_priv(dev);
+
+	return reset_release_bulk(&priv->resets);
+}
+
+static const struct udevice_id meson_gxbb_usb2_phy_ids[] = {
+	{ .compatible = "amlogic,meson8-usb2-phy" },
+	{ .compatible = "amlogic,meson8b-usb2-phy" },
+	{ .compatible = "amlogic,meson-gxbb-usb2-phy" },
+	{ }
+};

drivers/phy/meson-gxbb-usb2.c line 235

Quoted 10 lines
drivers/phy/meson-gxbb-usb2.c new file +10 -0
+
+U_BOOT_DRIVER(meson_gxbb_usb2_phy) = {
+	.name = "meson_gxbb_usb2_phy",
+	.id = UCLASS_PHY,
+	.of_match = meson_gxbb_usb2_phy_ids,
+	.probe = meson_gxbb_usb2_phy_probe,
+	.remove = meson_gxbb_usb2_phy_remove,
+	.ops = &meson_gxbb_usb2_phy_ops,
+	.priv_auto_alloc_size = sizeof(struct phy_meson_gxbb_usb2_priv),
+};

Applied to u-boot-amlogic

Next one will wait until Patrick's v6 is applied.

Neil

#4 lore raw

PATCH 2/2 odroid-c2: enable USB host controller

In reply to Beniamino Galvani

Enable the second USB controller, which is connected to a hub with 4 ports. The first controller is for the OTG port and is currently not supported.

---
 arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi | 8 ++++++++
 configs/odroid-c2_defconfig                  | 7 +++++++
 include/configs/meson64.h                    | 5 +++++
 3 files changed, 20 insertions(+)
arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi +8 -0
index c35158d7e9..484b40504d 100644
@@ -5,3 +5,11 @@
  */
 
 #include "meson-gx-u-boot.dtsi"
+
+&usb0 {
+	status = "disabled";
+};
+
+&usb1 {
+	hnp-srp-disable;
+};
configs/odroid-c2_defconfig +7 -0
index 8849058d33..366ea125af 100644
@@ -16,6 +16,7 @@ CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
 # CONFIG_CMD_LOADS is not set
 CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_REGULATOR=y
 CONFIG_OF_CONTROL=y
@@ -29,13 +30,19 @@ CONFIG_MMC_MESON_GX=y
 CONFIG_PHY_REALTEK=y
 CONFIG_DM_ETH=y
 CONFIG_ETH_DESIGNWARE=y
+CONFIG_PHY=y
+CONFIG_MESON_GXBB_USB_PHY=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_MESON_GXBB=y
 CONFIG_DM_REGULATOR=y
 CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
 CONFIG_DM_RESET=y
 CONFIG_DEBUG_UART_MESON=y
 CONFIG_DEBUG_UART_ANNOUNCE=y
 CONFIG_DEBUG_UART_SKIP_INIT=y
 CONFIG_MESON_SERIAL=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_DWC2=y
 CONFIG_OF_LIBFDT_OVERLAY=y
include/configs/meson64.h +5 -0
index f8d3eee292..483a8f567c 100644
@@ -16,6 +16,11 @@
 #define GICC_BASE			0xc4302000
 #endif
 
+/* USB */
+#if defined(CONFIG_MESON_GXBB)
+#define CONFIG_DWC2_UTMI_WIDTH		16
+#endif
+
 /* For splashscreen */
 #ifdef CONFIG_DM_VIDEO
 #define CONFIG_VIDEO_BMP_RLE8
Signature · 1 line
2.21.0
#5 lore raw

PATCH 2/2 odroid-c2: enable USB host controller

Quoted 64 lines · Beniamino Galvani

Enable the second USB controller, which is connected to a hub with 4 ports. The first controller is for the OTG port and is currently not supported.

---
 arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi | 8 ++++++++
 configs/odroid-c2_defconfig                  | 7 +++++++
 include/configs/meson64.h                    | 5 +++++
 3 files changed, 20 insertions(+)
arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi +8 -0
index c35158d7e9..484b40504d 100644
@@ -5,3 +5,11 @@
  */
 
 #include "meson-gx-u-boot.dtsi"
+
+&usb0 {
+	status = "disabled";
+};
+
+&usb1 {
+	hnp-srp-disable;
+};
configs/odroid-c2_defconfig +7 -0
index 8849058d33..366ea125af 100644
@@ -16,6 +16,7 @@ CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
 # CONFIG_CMD_LOADS is not set
 CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_REGULATOR=y
 CONFIG_OF_CONTROL=y
@@ -29,13 +30,19 @@ CONFIG_MMC_MESON_GX=y
 CONFIG_PHY_REALTEK=y
 CONFIG_DM_ETH=y
 CONFIG_ETH_DESIGNWARE=y
+CONFIG_PHY=y
+CONFIG_MESON_GXBB_USB_PHY=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_MESON_GXBB=y
 CONFIG_DM_REGULATOR=y
 CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
 CONFIG_DM_RESET=y
 CONFIG_DEBUG_UART_MESON=y
 CONFIG_DEBUG_UART_ANNOUNCE=y
 CONFIG_DEBUG_UART_SKIP_INIT=y
 CONFIG_MESON_SERIAL=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_DWC2=y
 CONFIG_OF_LIBFDT_OVERLAY=y
include/configs/meson64.h +0 -0
index f8d3eee292..483a8f567c 100644

include/configs/meson64.h line 22

Quoted 7 lines
include/configs/meson64.h +4 -0
@@ -16,6 +16,11 @@
 #define GICC_BASE			0xc4302000
 #endif
 
+/* USB */
+#if defined(CONFIG_MESON_GXBB)
+#define CONFIG_DWC2_UTMI_WIDTH		16
+#endif

Hi Neil,

I noticed this change to the bus width configuration isn't actually needed. The USB port works with or without it. The kernel driver doesn't set 16bit mode, so can you please remove these 4 lines from the commit before sending the pull request?

Thanks,
Beniamino

#6 lore raw

PATCH 2/2 odroid-c2: enable USB host controller

Hi,

Quoted 75 lines · Beniamino Galvani
Quoted 64 lines · Beniamino Galvani

Enable the second USB controller, which is connected to a hub with 4 ports. The first controller is for the OTG port and is currently not supported.

---
 arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi | 8 ++++++++
 configs/odroid-c2_defconfig                  | 7 +++++++
 include/configs/meson64.h                    | 5 +++++
 3 files changed, 20 insertions(+)
arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi +8 -0
index c35158d7e9..484b40504d 100644
@@ -5,3 +5,11 @@
  */
 
 #include "meson-gx-u-boot.dtsi"
+
+&usb0 {
+	status = "disabled";
+};
+
+&usb1 {
+	hnp-srp-disable;
+};
configs/odroid-c2_defconfig +7 -0
index 8849058d33..366ea125af 100644
@@ -16,6 +16,7 @@ CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
 # CONFIG_CMD_LOADS is not set
 CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_REGULATOR=y
 CONFIG_OF_CONTROL=y
@@ -29,13 +30,19 @@ CONFIG_MMC_MESON_GX=y
 CONFIG_PHY_REALTEK=y
 CONFIG_DM_ETH=y
 CONFIG_ETH_DESIGNWARE=y
+CONFIG_PHY=y
+CONFIG_MESON_GXBB_USB_PHY=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_MESON_GXBB=y
 CONFIG_DM_REGULATOR=y
 CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
 CONFIG_DM_RESET=y
 CONFIG_DEBUG_UART_MESON=y
 CONFIG_DEBUG_UART_ANNOUNCE=y
 CONFIG_DEBUG_UART_SKIP_INIT=y
 CONFIG_MESON_SERIAL=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_DWC2=y
 CONFIG_OF_LIBFDT_OVERLAY=y
include/configs/meson64.h +0 -0
index f8d3eee292..483a8f567c 100644

include/configs/meson64.h line 22

Quoted 7 lines
include/configs/meson64.h +4 -0
@@ -16,6 +16,11 @@
 #define GICC_BASE			0xc4302000
 #endif
 
+/* USB */
+#if defined(CONFIG_MESON_GXBB)
+#define CONFIG_DWC2_UTMI_WIDTH		16
+#endif

Hi Neil,

Quoted 8 lines

I noticed this change to the bus width configuration isn't actually needed. The USB port works with or without it. The kernel driver doesn't set 16bit mode, so can you please remove these 4 lines from the commit before sending the pull request?

Thanks,
Beniamino

Thanks,

I altered the commit removing this.

Neil

#7 lore raw
In reply to Beniamino Galvani
Quoted 11 lines · Beniamino Galvani

Hi,

these two patches enable the USB host controller on Odroid-C2. The first patch adds a PHY driver; the second one enables the necessary configuration options and updates the device tree.

Note that the DWC2 driver currently does not support enabling PHYs from the device tree and so the following series (still on review) is needed as runtime requirement for the second patch:

[PATCH 0/5] usb: host: dwc2: use driver model for PHY and CLOCK

Pushed to my u-boot-amlogic-next test tree until this dependency is applied.

Thanks,
Neil

Quoted 17 lines

Thanks,
Beniamino

Beniamino Galvani (2):
phy: meson: add GXBB PHY driver
odroid-c2: enable USB host controller

 arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi |   8 +
 configs/odroid-c2_defconfig                  |   7 +
 drivers/phy/Kconfig                          |   8 +
 drivers/phy/Makefile                         |   1 +
 drivers/phy/meson-gxbb-usb2.c                | 235 +++++++++++++++++++
 include/configs/meson64.h                    |   5 +
 6 files changed, 264 insertions(+)
 create mode 100644 drivers/phy/meson-gxbb-usb2.c
#8 lore raw
Quoted 7 lines · Neil Armstrong
Quoted 6 lines · Beniamino Galvani

Hi,

these two patches enable the USB host controller on Odroid-C2. The first patch adds a PHY driver; the second one enables the necessary configuration options and updates the device tree.

Quoted 8 lines
Quoted 5 lines

Note that the DWC2 driver currently does not support enabling PHYs from the device tree and so the following series (still on review) is needed as runtime requirement for the second patch:

[PATCH 0/5] usb: host: dwc2: use driver model for PHY and CLOCK

Pushed to my u-boot-amlogic-next test tree until this dependency is applied.

The resend version had some comments, could you resent when Patrick sends an updated version ?

Neil

Quoted 22 lines

Thanks,
Neil

Quoted 17 lines

Thanks,
Beniamino

Beniamino Galvani (2):
phy: meson: add GXBB PHY driver
odroid-c2: enable USB host controller

 arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi |   8 +
 configs/odroid-c2_defconfig                  |   7 +
 drivers/phy/Kconfig                          |   8 +
 drivers/phy/Makefile                         |   1 +
 drivers/phy/meson-gxbb-usb2.c                | 235 +++++++++++++++++++
 include/configs/meson64.h                    |   5 +
 6 files changed, 264 insertions(+)
 create mode 100644 drivers/phy/meson-gxbb-usb2.c
#9 lore raw
In reply to Beniamino Galvani

Hi,

Quoted 19 lines · Beniamino Galvani

Hi,

these two patches enable the USB host controller on Odroid-C2. The first patch adds a PHY driver; the second one enables the necessary configuration options and updates the device tree.

Note that the DWC2 driver currently does not support enabling PHYs from the device tree and so the following series (still on review) is needed as runtime requirement for the second patch:

[PATCH 0/5] usb: host: dwc2: use driver model for PHY and CLOCK

Thanks,
Beniamino

Beniamino Galvani (2):
phy: meson: add GXBB PHY driver
odroid-c2: enable USB host controller

Quoted 9 lines
 arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi |   8 +
 configs/odroid-c2_defconfig                  |   7 +
 drivers/phy/Kconfig                          |   8 +
 drivers/phy/Makefile                         |   1 +
 drivers/phy/meson-gxbb-usb2.c                | 235 +++++++++++++++++++
 include/configs/meson64.h                    |   5 +
 6 files changed, 264 insertions(+)
 create mode 100644 drivers/phy/meson-gxbb-usb2.c

Could you re-test with v6 of DWC2 patchset at http://patchwork.ozlabs.org/project/uboot/list/?series=163388 ?

Neil

#10 lore raw
Quoted 32 lines · Neil Armstrong

Hi,

Quoted 19 lines · Beniamino Galvani

Hi,

these two patches enable the USB host controller on Odroid-C2. The first patch adds a PHY driver; the second one enables the necessary configuration options and updates the device tree.

Note that the DWC2 driver currently does not support enabling PHYs from the device tree and so the following series (still on review) is needed as runtime requirement for the second patch:

[PATCH 0/5] usb: host: dwc2: use driver model for PHY and CLOCK

Thanks,
Beniamino

Beniamino Galvani (2):
phy: meson: add GXBB PHY driver
odroid-c2: enable USB host controller

Quoted 9 lines
 arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi |   8 +
 configs/odroid-c2_defconfig                  |   7 +
 drivers/phy/Kconfig                          |   8 +
 drivers/phy/Makefile                         |   1 +
 drivers/phy/meson-gxbb-usb2.c                | 235 +++++++++++++++++++
 include/configs/meson64.h                    |   5 +
 6 files changed, 264 insertions(+)
 create mode 100644 drivers/phy/meson-gxbb-usb2.c
Quoted 1 line

Could you re-test with v6 of DWC2 patchset at http://patchwork.ozlabs.org/project/uboot/list/?series=163388 ?

Hi,

I tested my two patches on top of Patrick's v6 and they still work as expected.

Thanks,
Beniamino